arm: armada-xp: Add basic support for the maxBCM board

The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.

Signed-off-by: Stefan Roese <sr@denx.de>

5 files changed, 121 insertions, 0 deletions

diff --git a/board/maxbcm/Kconfig b/board/maxbcm/Kconfig
new file mode 100644
index 0000000..d34e2ab
--- /dev/null
+++ b/board/maxbcm/Kconfig
@@ -0,0 +1,19 @@
+if TARGET_MAXBCM
+
+config SYS_CPU
+	string
+	default "armv7"
+
+config SYS_BOARD
+	string
+	default "maxbcm"
+
+config SYS_SOC
+	string
+	default "armada-xp"
+
+config SYS_CONFIG_NAME
+	string
+	default "maxbcm"
+
+endif
diff --git a/board/maxbcm/MAINTAINERS b/board/maxbcm/MAINTAINERS
new file mode 100644
index 0000000..3c8af21
--- /dev/null
+++ b/board/maxbcm/MAINTAINERS
@@ -0,0 +1,6 @@
+MAXBCM BOARD
+M:	Stefan Roese <sr@denx.de>
+S:	Maintained
+F:	board/maxbcm/
+F:	include/configs/maxbcm.h
+F:	configs/maxbcm_defconfig
diff --git a/board/maxbcm/Makefile b/board/maxbcm/Makefile
new file mode 100644
index 0000000..37c17d6
--- /dev/null
+++ b/board/maxbcm/Makefile
@@ -0,0 +1,7 @@
+#
+# Copyright (C) 2014 Stefan Roese <sr@denx.de>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= maxbcm.o
diff --git a/board/maxbcm/kwbimage.cfg b/board/maxbcm/kwbimage.cfg
new file mode 100644
index 0000000..5a3bc67
--- /dev/null
+++ b/board/maxbcm/kwbimage.cfg
@@ -0,0 +1,12 @@
+#
+# Copyright (C) 2014 Stefan Roese <sr@denx.de>
+#
+
+# Armada XP uses version 1 image format
+VERSION		1
+
+# Boot Media configurations
+BOOT_FROM	spi
+
+# Binary Header (bin_hdr) with DDR3 training code
+BINARY board/maxbcm/binary.0 0000005b 00000068
diff --git a/board/maxbcm/maxbcm.c b/board/maxbcm/maxbcm.c
new file mode 100644
index 0000000..7fc83ee
--- /dev/null
+++ b/board/maxbcm/maxbcm.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <linux/mbus.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Base addresses for the external device chip selects */
+#define DEV_CS0_BASE		0xe0000000
+#define DEV_CS1_BASE		0xe1000000
+#define DEV_CS2_BASE		0xe2000000
+#define DEV_CS3_BASE		0xe3000000
+
+/* Needed for dynamic (board-specific) mbus configuration */
+extern struct mvebu_mbus_state mbus_state;
+
+int board_early_init_f(void)
+{
+	/*
+	 * Don't configure MPP (pin multiplexing) and GPIO here,
+	 * its already done in bin_hdr
+	 */
+
+	/*
+	 * Setup some board specific mbus address windows
+	 */
+	mbus_dt_setup_win(&mbus_state, DEV_CS0_BASE, 16 << 20,
+			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS0);
+	mbus_dt_setup_win(&mbus_state, DEV_CS1_BASE, 16 << 20,
+			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS1);
+	mbus_dt_setup_win(&mbus_state, DEV_CS2_BASE, 16 << 20,
+			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS2);
+	mbus_dt_setup_win(&mbus_state, DEV_CS3_BASE, 16 << 20,
+			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS3);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: maxBCM\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E6185 switch */
+void reset_phy(void)
+{
+	u16 devadr = CONFIG_PHY_BASE_ADDR;
+	char *name = "neta0";
+	u16 reg;
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/* todo: fill this with the real setup / config code */
+
+	printf("88E6185 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */