omap730p2: Remove board

Signed-off-by: Tom Rini <trini@ti.com>

6 files changed, 0 insertions, 1222 deletions

diff --git a/board/ti/omap730p2/Makefile b/board/ti/omap730p2/Makefile
deleted file mode 100644
index 8242f3d..0000000
--- a/board/ti/omap730p2/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= omap730p2.o flash.o
-obj-y	+= lowlevel_init.o
diff --git a/board/ti/omap730p2/README.omap730p2 b/board/ti/omap730p2/README.omap730p2
deleted file mode 100644
index 7c70916..0000000
--- a/board/ti/omap730p2/README.omap730p2
+++ /dev/null
@@ -1,91 +0,0 @@
-
-		     u-boot for the TI OMAP730 Perseus2
-
-		      Dave Peverley, MPC-Data Limited
-			 http://www.mpc-data.co.uk
-
-
-Overview :
-
- As the OMAP730 is similar to the OMAP1610 in many ways, this port was based
-on the u-boot port to the OMAP1610 Innovator. Supported features are :
-
-  - Serial terminal support
-  - Onboard NOR Flash
-  - Ethernet via the seperate debug board
-  - Tested on Rev4 and Rev5 boards
-
- It has also been tested to work correctly when built with a 'standard' GCC
-3.2.1 cross-compiler as well as Montavista Linux CEE 3.1's toolchain.
-
-
-Hardware Configuration :
-
- The main dips on the P2 board should be set to 2,3,7 and 9 on with all
-others off. On the debug board, dips 1 and 7 should be on with the rest off.
-The serial console has been set up to run from the DB9 connector on the
-P2 board at 115200 baud, 8 data bits, no stop bits, 1 parity bit.
-
- It should be noted that the P2 board has NOR flash that is addressable via
-either CS0 or CS3. This mode can be changed via DIP9 on the P2 board.
-
-
-Installing u-boot for the P2 :
-
- You can simply build u-boot for the Perseus by following the instructions
-in the main readme file. The target configuration is "omap730p2_config".
-Once u-boot has been built, you should strip the executable so it can be
-loaded via CCS (which cant cope with the symbols in the ELF binary) :
-  $ cp u-boot u-boot.out
-  $ arm-linux-strip u-boot.out
-
- The method we've used for installing u-boot the first time on a P2 is
-as follows :
-
-1) Configure TI Code Composer Studio to connect to the P2 board via JTAG
-   as described in the Users Guide.
-
-2) Set up the P2 to boot from CS3, and connect with CCS. Reset the CPU
-   and run the "init_mmu" GEL script.
-
-3) Use the "Load Program" option to send the u-boot.out file to the P2 and
-   run.
-
- At this point, u-boot should run and you will see the boot menu on your
-serial terminal. You can then load the u-boot image to memory :
-
-  # loadb 0x10000000
-
- Send the "u-boot.bin" binary via the serial using Kermit. Once loaded
-you can self-flash u-boot :
-
-  # protect off 1:0
-  # erase 1:0
-  # cp.b 0x10000000 0x0 0x20000
-
- You should now be able to reset the board and run u-boot from flash.
-
-
-Alternative flash option :
-
- Sometimes, if you've been silly, you can get the board into a state where
-whats in flash has upset the board so much that you can no longer connect
-to the P2 via JTAG. However, you can set DIP9 to off to swap the boot mode
-of the P2 so that you boot from RAM instead of NOR flash. This moves NOR
-flash up to 0x0C000000. You can build a special version of u-boot to
-utilise this by the following config :
-
-  $ make omap730p2_cs0boot_config
-
- If you load this up via CCS it will detect flash at its alternate location
-and allow you to programme your u-boot image (which, remember must be built
-for CS3 boot!) Once you do this, you can revert to CS3 boot and it will work
-fine again.
-
-
-Errata :
-
-1) It's been observed that sometimes the tftp transfer of kernels to the
-   board can have checksum errors or stall. This appears to be an issue
-   with the lan91c96.c driver, and can normally be worked around by
-   resetting the board and trying again.
diff --git a/board/ti/omap730p2/config.mk b/board/ti/omap730p2/config.mk
deleted file mode 100644
index 8618820..0000000
--- a/board/ti/omap730p2/config.mk
+++ /dev/null
@@ -1,25 +0,0 @@
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# TI Perseus 2 board with OMAP720 (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# Innovator has 1 bank of 256 MB SDRAM
-# Physical Address:
-# 1000'0000 to 2000'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
-# (mem base + reserved)
-#
-# we load ourself to 1108'0000
-#
-#
-
-CONFIG_SYS_TEXT_BASE = 0x11080000
diff --git a/board/ti/omap730p2/flash.c b/board/ti/omap730p2/flash.c
deleted file mode 100644
index 56f981c..0000000
--- a/board/ti/omap730p2/flash.c
+++ /dev/null
@@ -1,463 +0,0 @@
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-
-#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 256 KB sectors (x2) */
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];	/* info for FLASH chips    */
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH		ushort
-#define FLASH_PORT_WIDTHV		vu_short
-#define SWAP(x)			__swab16(x)
-#else
-#define FLASH_PORT_WIDTH		ulong
-#define FLASH_PORT_WIDTHV		vu_long
-#define SWAP(x)			__swab32(x)
-#endif
-
-#define FPW	FLASH_PORT_WIDTH
-#define FPWV	FLASH_PORT_WIDTHV
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-
-/* Flash Organization Structure */
-typedef struct OrgDef {
-	unsigned int sector_number;
-	unsigned int sector_size;
-} OrgDef;
-
-
-/* Flash Organizations */
-OrgDef OrgIntel_28F256L18T[] = {
-	{4, 32 * 1024},				/* 4 * 32kBytes sectors */
-	{255, 128 * 1024},			/* 255 * 128kBytes sectors */
-};
-
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-unsigned long flash_init (void);
-static ulong flash_get_size (FPW * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-void inline spin_wheel (void);
-void flash_print_info (flash_info_t * info);
-void flash_unprotect_sectors (FPWV * addr);
-int flash_erase (flash_info_t * info, int s_first, int s_last);
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	int i;
-	ulong size = 0;
-	for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
-		switch (i) {
-		case 0:
-			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
-			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
-			break;
-		default:
-			panic ("configured too many flash banks!\n");
-			break;
-		}
-		size += flash_info[i].size;
-	}
-
-	/* Protect monitor and environment sectors
-	 */
-	flash_protect (FLAG_PROTECT_SET,
-			CONFIG_SYS_FLASH_BASE,
-			CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
-
-	flash_protect (FLAG_PROTECT_SET,
-			CONFIG_ENV_ADDR,
-			CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-
-	return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return;
-	}
-
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
-		for (i = 0; i < info->sector_count; i++) {
-			if (i > 255) {
-				info->start[i] = base + (i * 0x8000);
-				info->protect[i] = 0;
-			} else {
-				info->start[i] = base +
-						(i * PHYS_FLASH_SECT_SIZE);
-				info->protect[i] = 0;
-			}
-		}
-	}
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_INTEL:
-		printf ("INTEL ");
-		break;
-	default:
-		printf ("Unknown Vendor ");
-		break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_28F256L18T:
-		printf ("FLASH 28F256L18T\n");
-		break;
-	default:
-		printf ("Unknown Chip Type\n");
-		break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-			info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i = 0; i < info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i], info->protect[i] ? " (RO)" : "     ");
-	}
-	printf ("\n");
-	return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info)
-{
-	volatile FPW value;
-
-	/* Write auto select command: read Manufacturer ID */
-	addr[0x5555] = (FPW) 0x00AA00AA;
-	addr[0x2AAA] = (FPW) 0x00550055;
-	addr[0x5555] = (FPW) 0x00900090;
-
-	mb ();
-	value = addr[0];
-
-	switch (value) {
-
-	case (FPW) INTEL_MANUFACT:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
-		return (0);		/* no or unknown flash  */
-	}
-
-	mb ();
-	value = addr[1];	/* device ID        */
-	switch (value) {
-
-	case (FPW) (INTEL_ID_28F256L18T):
-		info->flash_id += FLASH_28F256L18T;
-		info->sector_count = 259;
-		info->size = 0x02000000;
-		break;			/* => 32 MB     */
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		break;
-	}
-
-	if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
-		printf ("** ERROR: sector count %d > max (%d) **\n",
-				info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
-		info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
-	}
-
-	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
-
-	return (info->size);
-}
-
-
-/* unprotects a sector for write and erase
- * on some intel parts, this unprotects the entire chip, but it
- * wont hurt to call this additional times per sector...
- */
-void flash_unprotect_sectors (FPWV * addr)
-{
-#define PD_FINTEL_WSMS_READY_MASK    0x0080
-
-	*addr = (FPW) 0x00500050;	/* clear status register */
-
-	/* this sends the clear lock bit command */
-	*addr = (FPW) 0x00600060;
-	*addr = (FPW) 0x00D000D0;
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
-	int flag, prot, sect;
-	ulong type, start;
-	int rcode = 0;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	type = (info->flash_id & FLASH_VENDMASK);
-	if ((type != FLASH_MAN_INTEL)) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-				info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect = s_first; sect <= s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-				prot);
-	} else {
-		printf ("\n");
-	}
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect <= s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			FPWV *addr = (FPWV *) (info->start[sect]);
-			FPW status;
-
-			printf ("Erasing sector %2d ... ", sect);
-
-			flash_unprotect_sectors (addr);
-
-			/* arm simple, non interrupt dependent timer */
-			start = get_timer(0);
-
-			*addr = (FPW) 0x00500050;/* clear status register */
-			*addr = (FPW) 0x00200020;/* erase setup */
-			*addr = (FPW) 0x00D000D0;/* erase confirm */
-
-			while (((status =
-				*addr) & (FPW) 0x00800080) !=
-				(FPW) 0x00800080) {
-					if (get_timer(start) >
-					CONFIG_SYS_FLASH_ERASE_TOUT) {
-					printf ("Timeout\n");
-					/* suspend erase     */
-					*addr = (FPW) 0x00B000B0;
-					/* reset to read mode */
-					*addr = (FPW) 0x00FF00FF;
-					rcode = 1;
-					break;
-				}
-			}
-
-			/* clear status register cmd.   */
-			*addr = (FPW) 0x00500050;
-			*addr = (FPW) 0x00FF00FF;/* resest to read mode */
-			printf (" done\n");
-		}
-	}
-
-	if (flag)
-		enable_interrupts();
-
-	return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
-	ulong cp, wp;
-	FPW data;
-	int count, i, l, rc, port_width;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return 4;
-	}
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
-	wp = (addr & ~1);
-	port_width = 2;
-#else
-	wp = (addr & ~3);
-	port_width = 4;
-#endif
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i = 0, cp = wp; i < l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-		for (; i < port_width && cnt > 0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt == 0 && i < port_width; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-
-		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	count = 0;
-	while (cnt >= port_width) {
-		data = 0;
-		for (i = 0; i < port_width; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-		cnt -= port_width;
-		if (count++ > 0x800) {
-			spin_wheel ();
-			count = 0;
-		}
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i < port_width; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *) cp);
-	}
-
-	return (write_data (info, wp, SWAP (data)));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
-	FPWV *addr = (FPWV *) dest;
-	ulong status;
-	int flag, rc = 0;
-	ulong start;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*addr & data) != data) {
-		printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
-		return (2);
-	}
-	flash_unprotect_sectors (addr);
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-	*addr = (FPW) 0x00400040;	/* write setup */
-	*addr = data;
-
-	/* arm simple, non interrupt dependent timer */
-	start = get_timer(0);
-
-	/* wait while polling the status register */
-	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
-		if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-			rc = 1;
-			goto done;
-		}
-	}
-done:
-	*addr = (FPW)0x00FF00FF;	/* restore read mode */
-	if (flag)
-		enable_interrupts();
-	return rc;
-}
-
-void inline spin_wheel (void)
-{
-	static int p = 0;
-	static char w[] = "\\/-";
-
-	printf ("\010%c", w[p]);
-	(++p == 3) ? (p = 0) : 0;
-}
diff --git a/board/ti/omap730p2/lowlevel_init.S b/board/ti/omap730p2/lowlevel_init.S
deleted file mode 100644
index 795c495..0000000
--- a/board/ti/omap730p2/lowlevel_init.S
+++ /dev/null
@@ -1,379 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003-2004
- *
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * Modified for OMAP730 P2 Board by Dave Peverley, MPC-Data Limited
- * (http://www.mpc-data.co.uk)
- *
- * TODO : Tidy up and change to use system register defines
- *        from omap730.h where possible.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP730)
-#include <./configs/omap730.h>
-#endif
-
-_TEXT_BASE:
-	.word	CONFIG_SYS_TEXT_BASE	/* sdram load addr from config.mk */
-
-.globl lowlevel_init
-lowlevel_init:
-	/* Save callers address in r11 - r11 must never be modified */
-	mov r11, lr
-
-	/*------------------------------------------------------*
-	 *mask all IRQs by setting all bits in the INTMR default*
-	 *------------------------------------------------------*/
-	mov	r1,	#0xffffffff
-	ldr	r0,	=REG_IHL1_MIR
-	str	r1,	[r0]
-	ldr	r0,	=REG_IHL2_MIR
-	str	r1,	[r0]
-
-	/*------------------------------------------------------*
-	 * Set up ARM CLM registers (IDLECT1)                   *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_ARM_IDLECT1
-	ldr	r1,	VAL_ARM_IDLECT1
-	str	r1,	[r0]
-
-	/*------------------------------------------------------*
-	 * Set up ARM CLM registers (IDLECT2)		        *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_ARM_IDLECT2
-	ldr	r1,	VAL_ARM_IDLECT2
-	str	r1,	[r0]
-
-	/*------------------------------------------------------*
-	 * Set up ARM CLM registers (IDLECT3)		        *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_ARM_IDLECT3
-	ldr	r1,	VAL_ARM_IDLECT3
-	str	r1,	[r0]
-
-
-	mov	r1,	#0x01		/* PER_EN bit */
-	ldr	r0,	REG_ARM_RSTCT2
-	strh	r1,	[r0]		/* CLKM; Peripheral reset. */
-
-	/* Set CLKM to Sync-Scalable	*/
-	/* I supposedly need to enable the dsp clock before switching */
-	mov	r1,	#0x1000
-	ldr	r0,	REG_ARM_SYSST
-	strh	r1,	[r0]
-	mov	r0,	#0x400
-1:
-	subs	r0,	r0,	#0x1	/* wait for any bubbles to finish */
-	bne	1b
-	ldr	r1,	VAL_ARM_CKCTL
-	ldr	r0,	REG_ARM_CKCTL
-	strh	r1,	[r0]
-
-	/* a few nops to let settle */
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-
-	/* setup DPLL 1 */
-	/* Ramp up the clock to 96Mhz */
-	ldr	r1,	VAL_DPLL1_CTL
-	ldr	r0,	REG_DPLL1_CTL
-	strh	r1,	[r0]
-	ands	r1,	r1,	#0x10	/* Check if PLL is enabled. */
-	beq	lock_end	/* Do not look for lock if BYPASS selected */
-2:
-	ldrh	r1,	[r0]
-	ands	r1,	r1,	#0x01	/*	Check the LOCK bit.*/
-	beq 2b			/*	loop until bit goes hi. */
-lock_end:
-
-	/*------------------------------------------------------*
-	 * Turn off the watchdog during init...			*
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_WATCHDOG
-	ldr	r1,	WATCHDOG_VAL1
-	str	r1,	[r0]
-	ldr	r1,	WATCHDOG_VAL2
-	str	r1,	[r0]
-	ldr	r0,	REG_WSPRDOG
-	ldr	r1,	WSPRDOG_VAL1
-	str	r1,	[r0]
-	ldr	r0,	REG_WWPSDOG
-
-watch1Wait:
-	ldr	r1,	[r0]
-	tst	r1,	#0x10
-	bne	watch1Wait
-
-	ldr	r0,	REG_WSPRDOG
-	ldr	r1,	WSPRDOG_VAL2
-	str	r1,	[r0]
-	ldr	r0,	REG_WWPSDOG
-watch2Wait:
-	ldr	r1,	[r0]
-	tst	r1,	#0x10
-	bne	watch2Wait
-
-	/* Set memory timings corresponding to the new clock speed */
-
-	/* Check execution location to determine current execution location
-	 * and branch to appropriate initialization code.
-	 */
-	/* Compare physical SDRAM base & current execution location. */
-	and     r0, pc, #0xF0000000
-	/* Compare. */
-	cmp     r0, #0
-	/* Skip over EMIF-fast initialization if running from SDRAM. */
-	bne	skip_sdram
-
-	/*
-	* Delay for SDRAM initialization.
-	*/
-	mov	r3,	#0x1800		/* value should be checked */
-3:
-	subs	r3,	r3,	#0x1	/* Decrement count */
-	bne	3b
-
-	ldr	r0,	REG_SDRAM_CONFIG
-	ldr	r1,	SDRAM_CONFIG_VAL
-	str	r1,	[r0]
-
-	ldr	r0,	REG_SDRAM_MRS_LEGACY
-	ldr	r1,	SDRAM_MRS_VAL
-	str	r1,	[r0]
-
-skip_sdram:
-
-common_tc:
-	/* slow interface */
-	ldr	r1,	VAL_TC_EMIFS_CS0_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS0_CONFIG
-	str	r1,	[r0] /* Chip Select 0 */
-
-	ldr	r1,	VAL_TC_EMIFS_CS1_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS1_CONFIG
-	str	r1,	[r0] /* Chip Select 1 */
-	ldr	r1,	VAL_TC_EMIFS_CS2_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS2_CONFIG
-	str	r1,	[r0] /* Chip Select 2 */
-	ldr	r1,	VAL_TC_EMIFS_CS3_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS3_CONFIG
-	str	r1,	[r0] /* Chip Select 3 */
-
-	/* 48MHz clock request for UART1 */
-	ldr	r1,	PERSEUS2_CONFIG_BASE
-	ldrh	r0,	[r1, #CONFIG_PCC_CONF]
-	orr	r0,	r0, #CONF_MOD_UART1_CLK_MODE_R
-	strh	r0,	[r1, #CONFIG_PCC_CONF]
-
-	/* Initialize public and private rheas
-	 *  - set access factor 2 on both rhea / strobe
-	 *  - disable write buffer on strb0, enable write buffer on strb1
-	 */
-
-	ldr	R0,	REG_RHEA_PUB_CTL
-	ldr	R1,	REG_RHEA_PRIV_CTL
-	ldr	R2,	VAL_RHEA_CTL
-	strh	R2,	[R0]
-	strh	R2,	[R1]
-	mov	R3,	#2          /* disable write buffer on strb0, enable write buffer on strb1 */
-	strh	R3,	[R0, #0x08]	/* arm rhea control reg */
-	strh	R3,	[R1, #0x08]
-
-	/* enable IRQ and FIQ */
-
-	mrs	r4,	CPSR
-	bic	r4,	r4, #IRQ_MASK
-	bic	r4,	r4, #FIQ_MASK
-	msr	CPSR,	r4
-
-	/* set TAP CONF to TRI EMULATION */
-
-	ldr	r1,	[r0, #CONFIG_MODE2]
-	bic	r1,	r1, #0x18
-	orr	r1,	r1, #0x10
-	str	r1,	[r0, #CONFIG_MODE2]
-
-	/* set tdbgen to 1 */
-
-	ldr	r0,	PERSEUS2_CONFIG_BASE
-	ldr	r1,	[r0, #CONFIG_MODE1]
-	mov	r2,	#0x10000
-	orr	r1,	r1, r2
-	str	r1,	[r0, #CONFIG_MODE1]
-
-#ifdef CONFIG_P2_OMAP1610
-	/* inserting additional 2 clock cycle hold time for LAN */
-	ldr     r0,     REG_TC_EMIFS_CS1_ADVANCED
-	ldr	r1,     VAL_TC_EMIFS_CS1_ADVANCED
-	str     r1,     [r0]
-#endif
-	/* Start MPU Timer 1 */
-	ldr	r0,	REG_MPU_LOAD_TIMER
-	ldr	r1,	VAL_MPU_LOAD_TIMER
-	str	r1,	[r0]
-
-	ldr	r0,	REG_MPU_CNTL_TIMER
-	ldr	r1,	VAL_MPU_CNTL_TIMER
-	str	r1,	[r0]
-
-	/* back to arch calling code */
-	mov	pc,	r11
-
-	/* the literal pools origin */
-	.ltorg
-
-REG_TC_EMIFS_CONFIG:		/* 32 bits */
-	.word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG:	/* 32 bits */
-	.word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG:	/* 32 bits */
-	.word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG:	/* 32 bits */
-	.word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG:	/* 32 bits */
-	.word 0xfffecc1c
-
-#ifdef CONFIG_P2_OMAP730
-REG_TC_EMIFS_CS1_ADVANCED:	/* 32 bits */
-	.word 0xfffecc54
-#endif
-
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL:			/* 16 bits */
-	.word 0xfffece00
-
-REG_ARM_IDLECT3:		/* 16 bits */
-	.word 0xfffece24
-REG_ARM_IDLECT2:		/* 16 bits */
-	.word 0xfffece08
-REG_ARM_IDLECT1:		/* 16 bits */
-	.word 0xfffece04
-
-REG_ARM_RSTCT2:			/* 16 bits */
-	.word 0xfffece14
-REG_ARM_SYSST:			/* 16 bits */
-	.word 0xfffece18
-/* DPLL control registers */
-REG_DPLL1_CTL:			/* 16 bits */
-	.word 0xfffecf00
-
-/* Watch Dog register */
-/* secure watchdog stop */
-REG_WSPRDOG:
-	.word 0xfffeb048
-/* watchdog write pending */
-REG_WWPSDOG:
-	.word 0xfffeb034
-
-WSPRDOG_VAL1:
-	.word 0x0000aaaa
-WSPRDOG_VAL2:
-	.word 0x00005555
-
-/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
- counter @8192 rows, 10 ns, 8 burst */
-REG_SDRAM_CONFIG:
-	.word 0xfffecc20
-
-REG_SDRAM_MRS_LEGACY:
-	.word 0xfffecc24
-
-REG_WATCHDOG:
-	.word 0xfffec808
-
-REG_MPU_LOAD_TIMER:
-	.word 0xfffec504
-REG_MPU_CNTL_TIMER:
-	.word 0xfffec500
-
-/* Public and private rhea bridge registers definition */
-
-REG_RHEA_PUB_CTL:
-	.word 0xFFFECA00
-
-REG_RHEA_PRIV_CTL:
-	.word 0xFFFED300
-
-/* EMIFF SDRAM Configuration register
-   - self refresh disable
-   - auto refresh enabled
-   - SDRAM type 64 Mb, 16 bits bus 4 banks
-   - power down enabled
-   - SDRAM clock disabled
- */
-SDRAM_CONFIG_VAL:
-	.word 0x0C017DF4
-
-/* Burst full page length ; cas latency = 3 */
-SDRAM_MRS_VAL:
-	.word 0x00000037
-
-VAL_ARM_CKCTL:
-	.word 0x6505
-VAL_DPLL1_CTL:
-	.word 0x3412
-
-#ifdef CONFIG_P2_OMAP730
-VAL_TC_EMIFS_CS0_CONFIG:
-	.word 0x0000FFF3
-VAL_TC_EMIFS_CS1_CONFIG:
-	.word 0x00004278
-VAL_TC_EMIFS_CS2_CONFIG:
-	.word 0x00004278
-VAL_TC_EMIFS_CS3_CONFIG:
-	.word 0x00004278
-VAL_TC_EMIFS_CS1_ADVANCED:
-	.word 0x00000022
-#endif
-
-VAL_ARM_IDLECT1:
-	.word 0x00000400
-VAL_ARM_IDLECT2:
-	.word 0x00000886
-VAL_ARM_IDLECT3:
-	.word 0x00000015
-
-WATCHDOG_VAL1:
-	.word 0x000000f5
-WATCHDOG_VAL2:
-	.word 0x000000a0
-
-VAL_MPU_LOAD_TIMER:
-	.word 0xffffffff
-VAL_MPU_CNTL_TIMER:
-	.word 0xffffffa1
-
-VAL_RHEA_CTL:
-	.word			0xFF22
-
-/* Config Register vals */
-PERSEUS2_CONFIG_BASE:
-	.word			0xFFFE1000
-
-.equ	CONFIG_PCC_CONF,	0xB4
-.equ	CONFIG_MODE1,		0x10
-.equ	CONFIG_MODE2,		0x14
-.equ	CONF_MOD_UART1_CLK_MODE_R,	0x0A
-
-/* misc values */
-.equ	IRQ_MASK,		0x80           /* IRQ mask value */
-.equ	FIQ_MASK,		0x40           /* FIQ mask value */
diff --git a/board/ti/omap730p2/omap730p2.c b/board/ti/omap730p2/omap730p2.c
deleted file mode 100644
index 554019c..0000000
--- a/board/ti/omap730p2/omap730p2.c
+++ /dev/null
@@ -1,255 +0,0 @@
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#if defined(CONFIG_OMAP730)
-#include <./configs/omap730.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int test_boot_mode(void);
-void spin_up_leds(void);
-void flash__init (void);
-void ether__init (void);
-void set_muxconf_regs (void);
-void peripheral_power_enable (void);
-
-#define FLASH_ON_CS0	1
-#define FLASH_ON_CS3	0
-
-static inline void delay (unsigned long loops)
-{
-	__asm__ volatile ("1:\n"
-			  "subs %0, %1, #1\n"
-			  "bne 1b":"=r" (loops):"0" (loops));
-}
-
-int test_boot_mode(void)
-{
-	/* Check for CS0 and CS3 address decode swapping */
-	if (*((volatile int *)EMIFS_CONFIG) & 0x00000002)
-		return(FLASH_ON_CS3);
-	else
-		return(FLASH_ON_CS0);
-}
-
-/* Toggle backup LED indication */
-void toggle_backup_led(void)
-{
-	static int  backupLEDState = 0;	 /* Init variable so that the LED will be ON the first time */
-	volatile unsigned int *IOConfReg;
-
-
-	IOConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DATA_OUTPUT);
-
-	if (backupLEDState != 0) {
-		*IOConfReg &= (0xFFFFEFFF);
-		backupLEDState = 0;
-	} else {
-		*IOConfReg |= (0x00001000);
-		backupLEDState = 1;
-	}
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
-	/* arch number of OMAP 730 P2 Board - Same as the Innovator! */
-	gd->bd->bi_arch_number = MACH_TYPE_OMAP_PERSEUS2;
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x10000100;
-
-	/* Configure MUX settings */
-	set_muxconf_regs ();
-
-	peripheral_power_enable ();
-
-	/* Backup LED indication via GPIO_140 -> Red led if MUX correctly setup */
-	toggle_backup_led();
-
-	/* Hold GSM in reset until needed */
-	*((volatile unsigned short *)M_CTL) &= ~1;
-
-	/*
-	 *  CSx timings, GPIO Mux ... setup
-	 */
-
-	/* Flash: CS0 timings setup */
-	*((volatile unsigned int *) FLASH_CFG_0) = 0x0000fff3;
-	*((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000088;
-
-	/* Ethernet support trough the debug board */
-	/* CS1 timings setup */
-	*((volatile unsigned int *) FLASH_CFG_1) = 0x0000fff3;
-	*((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000000;
-
-	/* this speeds up your boot a quite a bit.  However to make it
-	 *  work, you need make sure your kernel startup flush bug is fixed.
-	 *  ... rkw ...
-	 */
-	icache_enable ();
-
-	flash__init ();
-	ether__init ();
-
-	return 0;
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-void flash__init (void)
-{
-	unsigned int regval;
-
-	regval = *((volatile unsigned int *) EMIFS_CONFIG);
-	/* Turn off write protection for flash devices. */
-	regval = regval | 0x0001;
-	*((volatile unsigned int *) EMIFS_CONFIG) = regval;
-}
-
-/*************************************************************
- Routine:ether__init
- Description: take the Ethernet controller out of reset and wait
-			   for the EEPROM load to complete.
-*************************************************************/
-void ether__init (void)
-{
-#define LAN_RESET_REGISTER 0x0400001c
-
-	*((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
-	do {
-		*((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001;
-		udelay (100);
-	} while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001);
-
-	do {
-		*((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
-		udelay (100);
-	} while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000);
-
-#define ETH_CONTROL_REG 0x0400030b
-
-	*((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
-	udelay (100);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-int dram_init (void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
-}
-
-/******************************************************
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers
-			  specific to the hardware
-*******************************************************/
-void set_muxconf_regs (void)
-{
-	volatile unsigned int *MuxConfReg;
-	/* set each registers to its reset value; */
-
-	/*
-	 *  Backup LED Indication
-	 */
-
-	/* Configure MUXed pin. Mode 6: GPIO_140 */
-	MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF10);
-	*MuxConfReg &= (0xFFFFFF1F);	     /* Clear D_MPU_LPG1 */
-	*MuxConfReg |= 0x000000C0;	     /* Set D_MPU_LPG1 to 0x6 */
-
-	/* Configure GPIO_140 as output */
-	MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DIRECTION_CONTROL);
-	*MuxConfReg &= (0xFFFFEFFF);	     /* Clear direction (output) for GPIO 140 */
-
-	/*
-	 * Configure GPIOs for battery charge & feedback
-	 */
-
-	/* Configure MUXed pin. Mode 6: GPIO_35 */
-	MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3);
-	*MuxConfReg &= 0xFFFFFFF1;	     /* Clear M_CLK_OUT */
-	*MuxConfReg |= 0x0000000C;	     /* Set M_CLK_OUT = 0x6 (GPIOs) */
-
-	/* Configure MUXed pin. Mode 6: GPIO_72,73,74 */
-	MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF5);
-	*MuxConfReg &= 0xFFFF1FFF;	     /* Clear D_DDR */
-	*MuxConfReg |= 0x0000C000;	     /* Set D_DDR = 0x6 (GPIOs) */
-
-	MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DIRECTION_CONTROL);
-	*MuxConfReg |= 0x00000100;	     /* Configure GPIO_72 as input */
-	*MuxConfReg &= 0xFFFFFDFF;	     /* Configure GPIO_73 as output	*/
-
-	/*
-	 * Allow battery charge
-	 */
-
-	MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DATA_OUTPUT);
-	*MuxConfReg &= (0xFFFFFDFF);	     /* Clear GPIO_73 pin */
-
-	/*
-	 * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
-	 * It is used as the Ethernet controller interrupt
-	 */
-	MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF9);
-	*MuxConfReg &= 0x1FFFFFFF;
-}
-
-/******************************************************
- Routine: peripheral_power_enable
- Description: Enable the power for UART1
-*******************************************************/
-void peripheral_power_enable (void)
-{
-	volatile unsigned int *MuxConfReg;
-
-
-	/* Set up pins used by UART */
-
-	/* Start UART clock (48MHz) */
-	MuxConfReg = (volatile unsigned int *) (PERSEUS_PCC_CONF_REG);
-	*MuxConfReg &= (0xFFFFFFF7);
-	*MuxConfReg |= (0x00000008);
-
-	/* Get the UART pin in mode0  */
-	MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3);
-	*MuxConfReg &= (0xFF1FFFFF);
-	*MuxConfReg &= (0xF1FFFFFF);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_LAN91C96
-	rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
-#endif
-	return rc;
-}
-#endif