Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

15 files changed, 1415 insertions, 13 deletions

diff --git a/board/BuR/common/bur_common.h b/board/BuR/common/bur_common.h
new file mode 100644
index 0000000..15225b0
--- /dev/null
+++ b/board/BuR/common/bur_common.h
@@ -0,0 +1,22 @@
+/*
+ * bur_comon.h
+ *
+ * common board information header for B&R boards
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _BUR_COMMON_H_
+#define _BUR_COMMON_H_
+
+void blink(u32 blinks, u32 intervall, u32 pin);
+void pmicsetup(u32 mpupll);
+void enable_uart0_pin_mux(void);
+void enable_i2c0_pin_mux(void);
+void enable_board_pin_mux(void);
+int board_eth_init(bd_t *bis);
+
+#endif
diff --git a/board/BuR/common/common.c b/board/BuR/common/common.c
new file mode 100644
index 0000000..6d187ea
--- /dev/null
+++ b/board/BuR/common/common.c
@@ -0,0 +1,216 @@
+/*
+ * common.c
+ *
+ * common board functions for B&R boards
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include <power/tps65217.h>
+#include "bur_common.h"
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+/* --------------------------------------------------------------------------*/
+void blink(u32 blinks, u32 intervall, u32 pin)
+{
+	gpio_direction_output(pin, 0);
+	int val = 0;
+
+	do {
+		val ^= 0x01;
+		gpio_set_value(pin, val);
+		mdelay(intervall);
+	} while (blinks--);
+
+	gpio_set_value(pin, 0);
+}
+#ifdef CONFIG_SPL_BUILD
+void pmicsetup(u32 mpupll)
+{
+	int mpu_vdd;
+	int usb_cur_lim;
+
+	/* setup I2C */
+	enable_i2c0_pin_mux();
+	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+	if (i2c_probe(TPS65217_CHIP_PM)) {
+		puts("PMIC (0x24) not found! skip further initalization.\n");
+		return;
+	}
+
+	/* Get the frequency which is defined by device fuses */
+	dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+	printf("detected max. frequency: %d - ", dpll_mpu_opp100.m);
+
+	if (0 != mpupll) {
+		dpll_mpu_opp100.m = MPUPLL_M_1000;
+		printf("retuning MPU-PLL to: %d MHz.\n", dpll_mpu_opp100.m);
+	} else {
+		puts("ok.\n");
+	}
+	/*
+	 * Increase USB current limit to 1300mA or 1800mA and set
+	 * the MPU voltage controller as needed.
+	 */
+	if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
+		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
+		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
+	} else {
+		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
+		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
+	}
+
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
+			       usb_cur_lim, TPS65217_USB_INPUT_CUR_LIMIT_MASK))
+		puts("tps65217_reg_write failure\n");
+
+	/* Set DCDC3 (CORE) voltage to 1.125V */
+	if (tps65217_voltage_update(TPS65217_DEFDCDC3,
+				    TPS65217_DCDC_VOLT_SEL_1125MV)) {
+		puts("tps65217_voltage_update failure\n");
+		return;
+	}
+
+	/* Set CORE Frequencies to OPP100 */
+	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+	/* Set DCDC2 (MPU) voltage */
+	if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
+		puts("tps65217_voltage_update failure\n");
+		return;
+	}
+
+	/* Set LDO3 to 1.8V */
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+			       TPS65217_DEFLS1,
+			       TPS65217_LDO_VOLTAGE_OUT_1_8,
+			       TPS65217_LDO_MASK))
+		puts("tps65217_reg_write failure\n");
+	/* Set LDO4 to 3.3V */
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+			       TPS65217_DEFLS2,
+			       TPS65217_LDO_VOLTAGE_OUT_3_3,
+			       TPS65217_LDO_MASK))
+		puts("tps65217_reg_write failure\n");
+
+	/* Set MPU Frequency to what we detected now that voltages are set */
+	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+void set_uart_mux_conf(void)
+{
+	enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+	enable_board_pin_mux();
+}
+
+#endif /* CONFIG_SPL_BUILD */
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+	return;
+}
+
+/* describing port offsets of TI's CPSW block */
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_id		= 0,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_id		= 1,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+#endif /* CONFIG_DRIVER_TI_CPSW, ... */
+
+#if defined(CONFIG_DRIVER_TI_CPSW)
+
+int board_eth_init(bd_t *bis)
+{
+	int rv = 0;
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	/* try reading mac address from efuse */
+	mac_lo = readl(&cdev->macid0l);
+	mac_hi = readl(&cdev->macid0h);
+	mac_addr[0] = mac_hi & 0xFF;
+	mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+	mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+	mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+	mac_addr[4] = mac_lo & 0xFF;
+	mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+	if (!getenv("ethaddr")) {
+		printf("<ethaddr> not set. Validating first E-fuse MAC ... ");
+
+		if (is_valid_ether_addr(mac_addr)) {
+			printf("using: %02X:%02X:%02X:%02X:%02X:%02X.\n",
+			       mac_addr[0], mac_addr[1], mac_addr[2],
+			       mac_addr[3], mac_addr[4], mac_addr[5]
+				);
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+		}
+	}
+	writel(MII_MODE_ENABLE, &cdev->miisel);
+	cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
+	cpsw_slaves[1].phy_if =	PHY_INTERFACE_MODE_MII;
+
+	rv = cpsw_register(&cpsw_data);
+	if (rv < 0) {
+		printf("Error %d registering CPSW switch\n", rv);
+		return 0;
+	}
+#endif /* CONFIG_DRIVER_TI_CPSW, ... */
+	return rv;
+}
+#endif /* CONFIG_DRIVER_TI_CPSW */
diff --git a/board/BuR/kwb/Makefile b/board/BuR/kwb/Makefile
new file mode 100644
index 0000000..7b04b26
--- /dev/null
+++ b/board/BuR/kwb/Makefile
@@ -0,0 +1,12 @@
+#
+# Makefile
+#
+# Copyright (C) 2014 Hannes Petermaier <oe5hpm@oevsv.at> -
+# Bernecker & Rainer Industrielektronik GmbH - http://www.br-automation.com/
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-$(CONFIG_SPL_BUILD) += mux.o
+obj-y	+= ../common/common.o
+obj-y	+= board.o
diff --git a/board/BuR/kwb/board.c b/board/BuR/kwb/board.c
new file mode 100644
index 0000000..8aa16bc
--- /dev/null
+++ b/board/BuR/kwb/board.c
@@ -0,0 +1,240 @@
+/*
+ * board.c
+ *
+ * Board functions for B&R KWB Board
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ */
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <power/tps65217.h>
+#include "../common/bur_common.h"
+
+/* -------------------------------------------------------------------------*/
+/* -- defines for used GPIO Hardware -- */
+#define KEY						(0+4)
+#define LCD_PWR						(0+5)
+#define PUSH_KEY					(0+31)
+#define USB2SD_NRST					(32+29)
+#define USB2SD_PWR					(96+13)
+/* -------------------------------------------------------------------------*/
+/* -- PSOC Resetcontroller Register defines -- */
+
+/* I2C Address of controller */
+#define	RSTCTRL_ADDR				0x75
+/* Register for CTRL-word */
+#define RSTCTRL_CTRLREG				0x01
+/* Register for giving some information to VxWorks OS */
+#define RSTCTRL_SCRATCHREG			0x04
+
+/* -- defines for RSTCTRL_CTRLREG  -- */
+#define	RSTCTRL_FORCE_PWR_NEN			0x0404
+
+#if defined(CONFIG_SPL_BUILD)
+/* TODO: check ram-timing ! */
+static const struct ddr_data ddr3_data = {
+	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
+	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+	.cmd0csratio = MT41K256M16HA125E_RATIO,
+	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd1csratio = MT41K256M16HA125E_RATIO,
+	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd2csratio = MT41K256M16HA125E_RATIO,
+	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+	.zq_config = MT41K256M16HA125E_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+static const struct ctrl_ioregs ddr3_ioregs = {
+	.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+#define OSC	(V_OSCK/1000000)
+const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+	unsigned int oldspeed;
+	unsigned short buf;
+
+	struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER;
+	struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP;
+	/*
+	 * enable additional clocks of modules which are accessed later from
+	 * VxWorks OS
+	 */
+	u32 *const clk_domains[] = { 0 };
+
+	u32 *const clk_modules_kwbspecific[] = {
+		&cmwkup->wkup_adctscctrl,
+		&cmper->spi1clkctrl,
+		&cmper->dcan0clkctrl,
+		&cmper->dcan1clkctrl,
+		&cmper->epwmss0clkctrl,
+		&cmper->epwmss1clkctrl,
+		&cmper->epwmss2clkctrl,
+		0
+	};
+	do_enable_clocks(clk_domains, clk_modules_kwbspecific, 1);
+
+	/* power-OFF LCD-Display */
+	gpio_direction_output(LCD_PWR, 0);
+
+	/* setup I2C */
+	enable_i2c0_pin_mux();
+	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+	/* power-ON  3V3 via Resetcontroller */
+	oldspeed = i2c_get_bus_speed();
+	if (0 != i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC)) {
+		buf = RSTCTRL_FORCE_PWR_NEN;
+		i2c_write(RSTCTRL_ADDR, RSTCTRL_CTRLREG, 1,
+			  (uint8_t *)&buf, sizeof(buf));
+		i2c_set_bus_speed(oldspeed);
+	} else {
+		puts("ERROR: i2c_set_bus_speed failed! (turn on PWR_nEN)\n");
+	}
+
+#if defined(CONFIG_AM335X_USB0)
+	/* power on USB2SD Controller */
+	gpio_direction_output(USB2SD_PWR, 1);
+	mdelay(1);
+	/* give a reset Pulse to USB2SD Controller */
+	gpio_direction_output(USB2SD_NRST, 0);
+	mdelay(1);
+	gpio_set_value(USB2SD_NRST, 1);
+#endif
+	pmicsetup(0);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	return &dpll_ddr3;
+}
+
+void sdram_init(void)
+{
+	config_ddr(400, &ddr3_ioregs,
+		   &ddr3_data,
+		   &ddr3_cmd_ctrl_data,
+		   &ddr3_emif_reg_data, 0);
+}
+#endif /* CONFIG_SPL_BUILD */
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+	gpmc_init();
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+	const unsigned int ton  = 250;
+	const unsigned int toff = 1000;
+	unsigned int cnt  = 3;
+	unsigned short buf = 0xAAAA;
+	unsigned int oldspeed;
+
+	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+			   TPS65217_WLEDCTRL2, 0x32, 0xFF); /* 50% dimlevel */
+
+	if (gpio_get_value(KEY)) {
+		do {
+			/* turn on light */
+			tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+					   TPS65217_WLEDCTRL1, 0x09, 0xFF);
+			mdelay(ton);
+			/* turn off light */
+			tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+					   TPS65217_WLEDCTRL1, 0x01, 0xFF);
+			mdelay(toff);
+			cnt--;
+			if (!gpio_get_value(KEY) &&
+			    gpio_get_value(PUSH_KEY) && 1 == cnt) {
+				puts("updating from USB ...\n");
+				setenv("bootcmd", "run usbupdate");
+				break;
+			} else if (!gpio_get_value(KEY)) {
+				break;
+			}
+		} while (cnt);
+	}
+
+	switch (cnt) {
+	case 0:
+		puts("3 blinks ... entering BOOT mode.\n");
+		buf = 0x0000;
+		break;
+	case 1:
+		puts("2 blinks ... entering DIAGNOSE mode.\n");
+		buf = 0x0F0F;
+		break;
+	case 2:
+		puts("1 blinks ... entering SERVICE mode.\n");
+		buf = 0xB4B4;
+		break;
+	case 3:
+		puts("0 blinks ... entering RUN mode.\n");
+		buf = 0x0404;
+		break;
+	}
+	mdelay(ton);
+	/* turn on light */
+	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+			   TPS65217_WLEDCTRL1, 0x09, 0xFF);
+	/* write bootinfo into scratchregister of resetcontroller */
+	oldspeed = i2c_get_bus_speed();
+	if (0 != i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC)) {
+		i2c_write(RSTCTRL_ADDR, RSTCTRL_SCRATCHREG, 1,
+			  (uint8_t *)&buf, sizeof(buf));
+		i2c_set_bus_speed(oldspeed);
+	} else {
+		puts("ERROR: i2c_set_bus_speed failed! (scratchregister)\n");
+	}
+	/*
+	 * reset VBAR registers to its reset location, VxWorks 6.9.3.2 does
+	 * expect that vectors are there, original u-boot moves them to _start
+	 */
+	__asm__("ldr r0,=0x20000");
+	__asm__("mcr p15, 0, r0, c12, c0, 0"); /* Set VBAR */
+
+	return 0;
+}
+#endif /* CONFIG_BOARD_LATE_INIT */
diff --git a/board/BuR/kwb/mux.c b/board/BuR/kwb/mux.c
new file mode 100644
index 0000000..1a5ffd5
--- /dev/null
+++ b/board/BuR/kwb/mux.c
@@ -0,0 +1,195 @@
+/*
+ * mux.c
+ *
+ * Pinmux Setting for B&R LEIT Board(s)
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+
+static struct module_pin_mux usb0_pin_mux[] = {
+	{OFFSET(usb0_id), (MODE(0) | RXACTIVE)},
+	/* USB0 DrvBus Receiver disable (from romcode 0x20) */
+	{OFFSET(usb0_drvvbus), (MODE(0))},
+	/* USB1 DrvBus as GPIO due to HW-Workaround */
+	{OFFSET(usb1_drvvbus), (MODE(7))},
+	{-1},
+};
+static struct module_pin_mux spi1_pin_mux[] = {
+	/* SPI1_SCLK */
+	{OFFSET(mcasp0_aclkx), MODE(3) | PULLUDEN |             RXACTIVE},
+	/* SPI1_D0 */
+	{OFFSET(mcasp0_fsx),   MODE(3) | PULLUDEN |		RXACTIVE},
+	/* SPI1_D1 */
+	{OFFSET(mcasp0_axr0),  MODE(3) | PULLUDEN |             RXACTIVE},
+	/* SPI1_CS0 */
+	{OFFSET(mcasp0_ahclkr), MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE},
+	{-1},
+};
+
+static struct module_pin_mux dcan0_pin_mux[] = {
+	/* DCAN0 TX */
+	{OFFSET(uart1_ctsn),   MODE(2) | PULLUDEN | PULLUP_EN},
+	/* DCAN0 RX */
+	{OFFSET(uart1_rtsn),   MODE(2) | RXACTIVE},
+	{-1},
+};
+
+static struct module_pin_mux dcan1_pin_mux[] = {
+	/* DCAN1 TX */
+	{OFFSET(uart1_rxd),   MODE(2) | PULLUDEN | PULLUP_EN},
+	/* DCAN1 RX */
+	{OFFSET(uart1_txd),   MODE(2) | RXACTIVE},
+	{-1},
+};
+
+static struct module_pin_mux gpios[] = {
+	/* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
+	{OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS)},
+	/* GPIO0_4  (SPI D1) - TA602 */
+	{OFFSET(spi0_d1), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO0_5  (SPI CS0) - DISPLAY_ON_OFF */
+	{OFFSET(spi0_cs0), (MODE(7) | PULLUDDIS)},
+	/* GPIO0_7  (PWW0 OUT) - CAN TERM */
+	{OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO0_19 (DMA_INTR0) - CLKOUT SYS */
+	{OFFSET(xdma_event_intr0), (MODE(7) | RXACTIVE)},
+	/* GPIO0_20 (DMA_INTR1) - SPI1 nCS1 */
+	{OFFSET(xdma_event_intr1), (MODE(7) | PULLUDEN | PULLUP_EN)},
+	/* GPIO0_30 (GPMC_WAIT0) - TA601 */
+	{OFFSET(gpmc_wait0), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO0_31 (GPMC_nWP) - SW601 PushButton */
+	{OFFSET(gpmc_wpn), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO1_28 (GPMC_nWE) - FRAM_nWP */
+	{OFFSET(gpmc_be1n), (MODE(7) | PULLUDDIS)},
+	/* GPIO2_0  (GPMC_nCS3)	- VBAT_OK */
+	{OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) },
+	/* GPIO2_2  (GPMC_nADV_ALE) - DCOK */
+	{OFFSET(gpmc_advn_ale), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO2_4  (GPMC_nWE) - TST_BAST */
+	{OFFSET(gpmc_wen), (MODE(7) | PULLUDDIS)},
+	/* GPIO3_18 (MCASP0_ACLKR) - SW601 CNTup, mapped to Counter eQEB0A_in */
+	{OFFSET(mcasp0_aclkr), (MODE(1) | PULLUDDIS | RXACTIVE)},
+	/* GPIO3_19 (MCASP0_FSR) - SW601 CNTdown, mapped to Counter eQEB0B_in */
+	{OFFSET(mcasp0_fsr), (MODE(1) | PULLUDDIS | RXACTIVE)},
+	/* GPIO3_20 (MCASP0_AXR1) - SW601 CNTdown, map to Counter eQEB0_index */
+	{OFFSET(mcasp0_axr1), (MODE(1) | PULLUDDIS | RXACTIVE)},
+	{-1},
+};
+
+static struct module_pin_mux uart0_pin_mux[] = {
+	/* UART0_CTS */
+	{OFFSET(uart0_ctsn), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* UART0_RXD */
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* UART0_TXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
+	{-1},
+};
+
+static struct module_pin_mux i2c0_pin_mux[] = {
+	/* I2C_DATA */
+	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+	/* I2C_SCLK */
+	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+	{-1},
+};
+
+static struct module_pin_mux mii1_pin_mux[] = {
+	{OFFSET(mii1_rxerr), MODE(0) | RXACTIVE},	/* MII1_RXERR */
+	{OFFSET(mii1_txen), MODE(0)},			/* MII1_TXEN */
+	{OFFSET(mii1_rxdv), MODE(0) | RXACTIVE},	/* MII1_RXDV */
+	{OFFSET(mii1_txd3), MODE(0)},			/* MII1_TXD3 */
+	{OFFSET(mii1_txd2), MODE(0)},			/* MII1_TXD2 */
+	{OFFSET(mii1_txd1), MODE(0)},			/* MII1_TXD1 */
+	{OFFSET(mii1_txd0), MODE(0)},			/* MII1_TXD0 */
+	{OFFSET(mii1_txclk), MODE(0) | RXACTIVE},	/* MII1_TXCLK */
+	{OFFSET(mii1_rxclk), MODE(0) | RXACTIVE},	/* MII1_RXCLK */
+	{OFFSET(mii1_rxd3), MODE(0) | RXACTIVE},	/* MII1_RXD3 */
+	{OFFSET(mii1_rxd2), MODE(0) | RXACTIVE},	/* MII1_RXD2 */
+	{OFFSET(mii1_rxd1), MODE(0) | RXACTIVE},	/* MII1_RXD1 */
+	{OFFSET(mii1_rxd0), MODE(0) | RXACTIVE},	/* MII1_RXD0 */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+static struct module_pin_mux mmc1_pin_mux[] = {
+	{OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT3 */
+	{OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT2 */
+	{OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT1 */
+	{OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT0 */
+	{OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CLK */
+	{OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CMD */
+	{OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)},	/* MMC1_WP */
+	{OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
+
+	{-1},
+};
+
+static struct module_pin_mux lcd_pin_mux[] = {
+	{OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)},	/* LCD-Data(0) */
+	{OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)},	/* LCD-Data(1) */
+	{OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)},	/* LCD-Data(2) */
+	{OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)},	/* LCD-Data(3) */
+	{OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)},	/* LCD-Data(4) */
+	{OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)},	/* LCD-Data(5) */
+	{OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)},	/* LCD-Data(6) */
+	{OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)},	/* LCD-Data(7) */
+	{OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)},	/* LCD-Data(8) */
+	{OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)},	/* LCD-Data(9) */
+	{OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)},	/* LCD-Data(10) */
+	{OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)},	/* LCD-Data(11) */
+	{OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)},	/* LCD-Data(12) */
+	{OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)},	/* LCD-Data(13) */
+	{OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)},	/* LCD-Data(14) */
+	{OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)},	/* LCD-Data(15) */
+
+	{OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)},	/* LCD-Data(16) */
+	{OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)},	/* LCD-Data(17) */
+	{OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)},	/* LCD-Data(18) */
+	{OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)},	/* LCD-Data(19) */
+	{OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)},	/* LCD-Data(20) */
+	{OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)},	/* LCD-Data(21) */
+	{OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)},	/* LCD-Data(22) */
+	{OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)},	/* LCD-Data(23) */
+
+	{OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)},	/* LCD-VSync */
+	{OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)},	/* LCD-HSync */
+	{OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */
+	{OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)},	/* LCD-CLK */
+
+	{-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_board_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+	configure_module_pin_mux(mii1_pin_mux);
+	configure_module_pin_mux(usb0_pin_mux);
+	configure_module_pin_mux(spi1_pin_mux);
+	configure_module_pin_mux(dcan0_pin_mux);
+	configure_module_pin_mux(dcan1_pin_mux);
+	configure_module_pin_mux(mmc1_pin_mux);
+	configure_module_pin_mux(lcd_pin_mux);
+	configure_module_pin_mux(gpios);
+}
diff --git a/board/BuR/tseries/Makefile b/board/BuR/tseries/Makefile
new file mode 100644
index 0000000..ec0d27a
--- /dev/null
+++ b/board/BuR/tseries/Makefile
@@ -0,0 +1,14 @@
+#
+# Makefile
+#
+# Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+# Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifeq ($(CONFIG_SPL_BUILD),y)
+obj-y	:= mux.o
+endif
+obj-y	+= ../common/common.o
+obj-y	+= board.o
diff --git a/board/BuR/tseries/board.c b/board/BuR/tseries/board.c
new file mode 100644
index 0000000..f0510e5
--- /dev/null
+++ b/board/BuR/tseries/board.c
@@ -0,0 +1,147 @@
+/*
+ * board.c
+ *
+ * Board functions for B&R LEIT Board
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <power/tps65217.h>
+#include "../common/bur_common.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* --------------------------------------------------------------------------*/
+/* -- defines for GPIO -- */
+#define	ETHLED_ORANGE	(96+16)	/* GPIO3_16 */
+#define	REPSWITCH	(0+20)	/* GPIO0_20 */
+
+
+#if defined(CONFIG_SPL_BUILD)
+/* TODO: check ram-timing ! */
+static const struct ddr_data ddr3_data = {
+	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
+	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+	.cmd0csratio = MT41K256M16HA125E_RATIO,
+	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd1csratio = MT41K256M16HA125E_RATIO,
+	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd2csratio = MT41K256M16HA125E_RATIO,
+	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+	.zq_config = MT41K256M16HA125E_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+static const struct ctrl_ioregs ddr3_ioregs = {
+	.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+/*
+ * called from spl_nand.c
+ * return 0 for loading linux, return 1 for loading u-boot
+ */
+int spl_start_uboot(void)
+{
+	if (0 == gpio_get_value(REPSWITCH)) {
+		blink(5, 125, ETHLED_ORANGE);
+		mdelay(1000);
+		printf("SPL: entering u-boot instead kernel image.\n");
+		return 1;
+	}
+	return 0;
+}
+#endif /* CONFIG_SPL_OS_BOOT */
+
+#define OSC	(V_OSCK/1000000)
+static const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+	pmicsetup(1000);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	return &dpll_ddr3;
+}
+
+void sdram_init(void)
+{
+	config_ddr(400, &ddr3_ioregs,
+		   &ddr3_data,
+		   &ddr3_cmd_ctrl_data,
+		   &ddr3_emif_reg_data, 0);
+}
+#endif /* CONFIG_SPL_BUILD */
+
+/* Basic board specific setup.  Pinmux has been handled already. */
+int board_init(void)
+{
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+	gpmc_init();
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+	gpio_direction_output(ETHLED_ORANGE, 0);
+
+	if (0 == gpio_get_value(REPSWITCH)) {
+		printf("\n\n\n"
+		"!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n"
+		"!!!!!!! recovery switch activated !!!!!!!\n"
+		"!!!!!!!     running usbupdate     !!!!!!!\n"
+		"!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n\n\n");
+		setenv("bootcmd", "sleep 2; run netupdate;");
+	}
+
+	printf("turning on display power+backlight ... ");
+	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL1,
+			   0x09, TPS65217_MASK_ALL_BITS);	/* 200 Hz, ON */
+	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL2,
+			   0x62, TPS65217_MASK_ALL_BITS);	/* 100% */
+	printf("ok.\n");
+
+	return 0;
+}
+#endif /* CONFIG_BOARD_LATE_INIT */
diff --git a/board/BuR/tseries/mux.c b/board/BuR/tseries/mux.c
new file mode 100644
index 0000000..3c76e96
--- /dev/null
+++ b/board/BuR/tseries/mux.c
@@ -0,0 +1,225 @@
+/*
+ * mux.c
+ *
+ * Pinmux Setting for B&R LEIT Board(s)
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+
+static struct module_pin_mux uart0_pin_mux[] = {
+	/* UART0_CTS */
+	{OFFSET(uart0_ctsn), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* UART0_RXD */
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* UART0_TXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
+	{-1},
+};
+#ifdef CONFIG_MMC
+static struct module_pin_mux mmc1_pin_mux[] = {
+	{OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT3 */
+	{OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT2 */
+	{OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT1 */
+	{OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT0 */
+	{OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CLK */
+	{OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CMD */
+	{OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)},	/* MMC1_WP */
+	{OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
+	{-1},
+};
+#endif
+static struct module_pin_mux i2c0_pin_mux[] = {
+	/* I2C_DATA */
+	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+	/* I2C_SCLK */
+	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+	{-1},
+};
+
+static struct module_pin_mux spi0_pin_mux[] = {
+	/* SPI0_SCLK */
+	{OFFSET(spi0_sclk), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+	/* SPI0_D0 */
+	{OFFSET(spi0_d0), (MODE(0) | RXACTIVE |	PULLUDEN | PULLUP_EN)},
+	/* SPI0_D1 */
+	{OFFSET(spi0_d1), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+	/* SPI0_CS0 */
+	{OFFSET(spi0_cs0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+	{-1},
+};
+
+static struct module_pin_mux mii1_pin_mux[] = {
+	{OFFSET(mii1_rxerr), MODE(0) | RXACTIVE},	/* MII1_RXERR */
+	{OFFSET(mii1_txen), MODE(0)},			/* MII1_TXEN */
+	{OFFSET(mii1_rxdv), MODE(0) | RXACTIVE},	/* MII1_RXDV */
+	{OFFSET(mii1_txd3), MODE(0)},			/* MII1_TXD3 */
+	{OFFSET(mii1_txd2), MODE(0)},			/* MII1_TXD2 */
+	{OFFSET(mii1_txd1), MODE(0)},			/* MII1_TXD1 */
+	{OFFSET(mii1_txd0), MODE(0)},			/* MII1_TXD0 */
+	{OFFSET(mii1_txclk), MODE(0) | RXACTIVE},	/* MII1_TXCLK */
+	{OFFSET(mii1_rxclk), MODE(0) | RXACTIVE},	/* MII1_RXCLK */
+	{OFFSET(mii1_rxd3), MODE(0) | RXACTIVE},	/* MII1_RXD3 */
+	{OFFSET(mii1_rxd2), MODE(0) | RXACTIVE},	/* MII1_RXD2 */
+	{OFFSET(mii1_rxd1), MODE(0) | RXACTIVE},	/* MII1_RXD1 */
+	{OFFSET(mii1_rxd0), MODE(0) | RXACTIVE},	/* MII1_RXD0 */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+static struct module_pin_mux mii2_pin_mux[] = {
+	{OFFSET(gpmc_a0), MODE(1)},		/* MII2_TXEN */
+	{OFFSET(gpmc_a1), MODE(1) | RXACTIVE},	/* MII2_RXDV */
+	{OFFSET(gpmc_a2), MODE(1)},		/* MII2_TXD3 */
+	{OFFSET(gpmc_a3), MODE(1)},		/* MII2_TXD2 */
+	{OFFSET(gpmc_a4), MODE(1)},		/* MII2_TXD1 */
+	{OFFSET(gpmc_a5), MODE(1)},		/* MII2_TXD0 */
+	{OFFSET(gpmc_a6), MODE(1) | RXACTIVE},	/* MII2_TXCLK */
+	{OFFSET(gpmc_a7), MODE(1) | RXACTIVE},	/* MII2_RXCLK */
+	{OFFSET(gpmc_a8), MODE(1) | RXACTIVE},	/* MII2_RXD3 */
+	{OFFSET(gpmc_a9), MODE(1) | RXACTIVE},	/* MII2_RXD2 */
+	{OFFSET(gpmc_a10), MODE(1) | RXACTIVE},	/* MII2_RXD1 */
+	{OFFSET(gpmc_a11), MODE(1) | RXACTIVE},	/* MII2_RXD0 */
+	{OFFSET(gpmc_wpn), (MODE(1) | RXACTIVE)},/* MII2_RXERR */
+						/*
+						 * MII2_CRS is shared with
+						 * NAND_WAIT0
+						 */
+	{OFFSET(gpmc_be1n), (MODE(1) | RXACTIVE)},/* MII1_COL */
+	{-1},
+};
+#ifdef CONFIG_NAND
+static struct module_pin_mux nand_pin_mux[] = {
+	{OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD0 */
+	{OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD1 */
+	{OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD2 */
+	{OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD3 */
+	{OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD4 */
+	{OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD5 */
+	{OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD6 */
+	{OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD7 */
+	{OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* NAND WAIT */
+	{OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)},	/* NAND_WPN */
+	{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)},	/* NAND_CS0 */
+	{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)},	/* NAND_ADV_ALE */
+	{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)},	/* NAND_OE */
+	{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)},	/* NAND_WEN */
+	{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)},	/* NAND_BE_CLE */
+	{-1},
+};
+#endif
+static struct module_pin_mux gpIOs[] = {
+	/* GPIO0_6  (SPI0_CS1) - 3v3_PWR_nEN (Display Power Supply) */
+	{OFFSET(spi0_cs1),  (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* TIMER5   (MMC0_DAT3) - TIMER5 (Buzzer) */
+	{OFFSET(mmc0_dat3), (MODE(3) | PULLUDEN | RXACTIVE)},
+	/* TIMER6   (MMC0_DAT2) - PWM_BACK_3V3, later used as MODE3 for PWM */
+	{OFFSET(mmc0_dat2), (MODE(7) | PULLUDEN | RXACTIVE)},
+	/* GPIO2_28 (MMC0_DAT1)	 - MII_nNAND */
+	{OFFSET(mmc0_dat1), (MODE(7) | PULLUDEN | RXACTIVE)},
+	/* GPIO2_29 (MMC0_DAT0)	 - NAND_1n0 */
+	{OFFSET(mmc0_dat0), (MODE(7) | PULLUDEN | RXACTIVE)},
+	/* GPIO2_30 (MMC0_CLK) - nRESET (PHY) */
+	{OFFSET(mmc0_clk), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO3_18 (MCASP0_ACLKR) - CPLD JTAG TDI */
+	{OFFSET(mcasp0_aclkr), (MODE(7) | PULLUDEN | PULLUP_EN  | RXACTIVE)},
+	/* GPIO3_19 (MCASP0_FSR) - CPLD JTAG TMS */
+	{OFFSET(mcasp0_fsr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO3_20 (MCASP0_AXR1) - CPLD JTAG TCK */
+	{OFFSET(mcasp0_axr1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO3_21 (MCASP0_AHCLKX) - CPLD JTAG TDO */
+	{OFFSET(mcasp0_ahclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO2_0  (GPMC_nCS3) - DCOK */
+	{OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) },
+	/* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
+	{OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS | RXACTIVE) },
+	/*
+	 * GPIO0_7 (PWW0 OUT)
+	 * DISPLAY_ONOFF (Backlight Enable at LVDS Versions)
+	 */
+	{OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN | RXACTIVE)},
+	/* GPIO0_19 (DMA_INTR0) - ISPLAY_MODE (CPLD) */
+	{OFFSET(xdma_event_intr0), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO0_20 (DMA_INTR1) - REP-Switch */
+	{OFFSET(xdma_event_intr1), (MODE(7) | PULLUP_EN | RXACTIVE)},
+	/* GPIO3_14 (MCASP0_ACLKX) - frei / PP709 */
+	{OFFSET(mcasp0_aclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
+	/* GPIO3_15 (MCASP0_FSX) - PMIC_nRESET */
+	{OFFSET(mcasp0_fsx),   (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
+	/* GPIO3_16 (MCASP0_AXR0) - ETH1_LEDY */
+	{OFFSET(mcasp0_axr0),  (MODE(7) | PULLUDDIS) },
+	/* GPIO3_17 (MCASP0_AHCLKR) - ETH2_LEDY */
+	{OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS) },
+
+	{-1},
+};
+
+static struct module_pin_mux lcd_pin_mux[] = {
+	{OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)},	/* LCD-Data(0) */
+	{OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)},	/* LCD-Data(1) */
+	{OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)},	/* LCD-Data(2) */
+	{OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)},	/* LCD-Data(3) */
+	{OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)},	/* LCD-Data(4) */
+	{OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)},	/* LCD-Data(5) */
+	{OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)},	/* LCD-Data(6) */
+	{OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)},	/* LCD-Data(7) */
+	{OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)},	/* LCD-Data(8) */
+	{OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)},	/* LCD-Data(9) */
+	{OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)},	/* LCD-Data(10) */
+	{OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)},	/* LCD-Data(11) */
+	{OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)},	/* LCD-Data(12) */
+	{OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)},	/* LCD-Data(13) */
+	{OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)},	/* LCD-Data(14) */
+	{OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)},	/* LCD-Data(15) */
+
+	{OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)},	/* LCD-Data(16) */
+	{OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)},	/* LCD-Data(17) */
+	{OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)},	/* LCD-Data(18) */
+	{OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)},	/* LCD-Data(19) */
+	{OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)},	/* LCD-Data(20) */
+	{OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)},	/* LCD-Data(21) */
+	{OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)},	/* LCD-Data(22) */
+	{OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)},	/* LCD-Data(23) */
+
+	{OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)},	/* LCD-VSync */
+	{OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)},	/* LCD-HSync */
+	{OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */
+	{OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)},	/* LCD-CLK */
+
+	{-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_board_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+	configure_module_pin_mux(mii1_pin_mux);
+	configure_module_pin_mux(mii2_pin_mux);
+#ifdef CONFIG_NAND
+	configure_module_pin_mux(nand_pin_mux);
+#elif defined(CONFIG_MMC)
+	configure_module_pin_mux(mmc1_pin_mux);
+#endif
+	configure_module_pin_mux(spi0_pin_mux);
+	configure_module_pin_mux(lcd_pin_mux);
+	configure_module_pin_mux(gpIOs);
+}
diff --git a/board/htkw/mcx/mcx.h b/board/htkw/mcx/mcx.h
index 703dbec..17c122c 100644
--- a/board/htkw/mcx/mcx.h
+++ b/board/htkw/mcx/mcx.h
@@ -325,8 +325,6 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | EN  | M4)) \
 	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)) \
 	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTD | EN  | M4)) \
-	MUX_VAL(CP(SYS_NRESWARM),	(IEN | PTU | DIS | M4)) \
-					/* SYS_nRESWARM */\
 	MUX_VAL(CP(SYS_BOOT0),		(IEN  | PTD | DIS | M4)) \
 	MUX_VAL(CP(SYS_BOOT1),		(IEN  | PTD | DIS | M4)) \
 	MUX_VAL(CP(SYS_BOOT2),		(IEN  | PTD | DIS | M4)) \
diff --git a/board/silica/pengwyn/Makefile b/board/silica/pengwyn/Makefile
new file mode 100644
index 0000000..c8b4f9a
--- /dev/null
+++ b/board/silica/pengwyn/Makefile
@@ -0,0 +1,13 @@
+#
+# Makefile
+#
+# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_NOR_BOOT),y)
+obj-y	:= mux.o
+endif
+
+obj-y	+= board.o
diff --git a/board/silica/pengwyn/board.c b/board/silica/pengwyn/board.c
new file mode 100644
index 0000000..a553129
--- /dev/null
+++ b/board/silica/pengwyn/board.c
@@ -0,0 +1,207 @@
+/*
+ * board.c
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+#include <phy.h>
+#include <cpsw.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+#if defined(CONFIG_SPL_BUILD)
+
+/* DDR3 RAM timings */
+static const struct ddr_data ddr3_data = {
+	.datardsratio0 = MT41K128MJT187E_RD_DQS,
+	.datawdsratio0 = MT41K128MJT187E_WR_DQS,
+	.datafwsratio0 = MT41K128MJT187E_PHY_FIFO_WE,
+	.datawrsratio0 = MT41K128MJT187E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+	.cmd0csratio = MT41K128MJT187E_RATIO,
+	.cmd0iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+	.cmd1csratio = MT41K128MJT187E_RATIO,
+	.cmd1iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+	.cmd2csratio = MT41K128MJT187E_RATIO,
+	.cmd2iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = MT41K128MJT187E_EMIF_SDCFG,
+	.ref_ctrl = MT41K128MJT187E_EMIF_SDREF,
+	.sdram_tim1 = MT41K128MJT187E_EMIF_TIM1,
+	.sdram_tim2 = MT41K128MJT187E_EMIF_TIM2,
+	.sdram_tim3 = MT41K128MJT187E_EMIF_TIM3,
+	.zq_config = MT41K128MJT187E_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41K128MJT187E_EMIF_READ_LATENCY |
+				PHY_EN_DYN_PWRDN,
+};
+
+const struct ctrl_ioregs ddr3_ioregs = {
+	.cm0ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+	.cm1ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+	.cm2ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+	.dt0ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+	.dt1ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+	/* break into full u-boot on 'c' */
+	return serial_tstc() && serial_getc() == 'c';
+}
+#endif
+
+#define OSC	(V_OSCK/1000000)
+const struct dpll_params dpll_ddr_266 = {
+		266, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_303 = {
+		303, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_400 = {
+		400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+	/*
+	 * The pengwyn board uses the TPS650250 PMIC  without I2C
+	 * interface and will output the following fixed voltages:
+	 * DCDC1=3V3 (IO) DCDC2=1V5 (DDR) DCDC3=1V26 (Vmpu)
+	 * VLDO1=1V8 (IO) VLDO2=1V8(IO)
+	 * Vcore=1V1 is fixed, generated by TPS62231
+	 */
+
+	/* Get the frequency */
+	dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+
+	/* Set CORE Frequencies to OPP100 */
+	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+	/* 720MHz cpu, this might change on newer board revisions */
+	dpll_mpu_opp100.m = MPUPLL_M_720;
+	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	/* future configs can return other clock settings */
+	return &dpll_ddr_303;
+}
+
+void set_uart_mux_conf(void)
+{
+	enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+	enable_board_pin_mux();
+}
+
+void sdram_init(void)
+{
+	config_ddr(303, &ddr3_ioregs, &ddr3_data,
+		   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
+}
+#endif /* if CONFIG_SPL_BUILD */
+
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+	gpmc_init();
+	return 0;
+}
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_id		= 0,
+		.phy_if		= PHY_INTERFACE_MODE_MII,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_id		= 1,
+		.phy_if		= PHY_INTERFACE_MODE_MII,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+	int rv, n = 0;
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+		printf("<ethaddr> not set. Reading from E-fuse\n");
+		/* try reading mac address from efuse */
+		mac_lo = readl(&cdev->macid0l);
+		mac_hi = readl(&cdev->macid0h);
+		mac_addr[0] = mac_hi & 0xFF;
+		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+		mac_addr[4] = mac_lo & 0xFF;
+		mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+		else
+			return n;
+	}
+
+	writel(MII_MODE_ENABLE, &cdev->miisel);
+
+	rv = cpsw_register(&cpsw_data);
+	if (rv < 0)
+		printf("Error %d registering CPSW switch\n", rv);
+	else
+		n += rv;
+	return n;
+}
+#endif /* if CONFIG_DRIVER_TI_CPSW */
diff --git a/board/silica/pengwyn/board.h b/board/silica/pengwyn/board.h
new file mode 100644
index 0000000..05addf6
--- /dev/null
+++ b/board/silica/pengwyn/board.h
@@ -0,0 +1,15 @@
+/*
+ * board.h
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+void enable_uart0_pin_mux(void);
+void enable_board_pin_mux(void);
+
+#endif
diff --git a/board/silica/pengwyn/mux.c b/board/silica/pengwyn/mux.c
new file mode 100644
index 0000000..c8be440
--- /dev/null
+++ b/board/silica/pengwyn/mux.c
@@ -0,0 +1,98 @@
+/*
+ * mux.c
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include "board.h"
+
+/* UART0 pins E15(rx),E16(tx) [E17(rts),E18(cts)] */
+static struct module_pin_mux uart0_pin_mux[] = {
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* UART0_RXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},		/* UART0_TXD */
+	{-1},
+};
+
+/* unused: UART1 pins D15(tx),D16(rx),D17(cts),D18(rts) */
+
+/* I2C pins C16(scl)/C17(sda) */
+static struct module_pin_mux i2c0_pin_mux[] = {
+	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
+					PULLUDEN | SLEWCTRL)}, /* I2C0_DATA */
+	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
+					PULLUDEN | SLEWCTRL)}, /* I2C0_SCLK */
+	{-1},
+};
+
+/* MMC0 pins */
+static struct module_pin_mux mmc0_pin_mux[] = {
+	{OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */
+	{OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */
+	{OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */
+	{OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */
+	{OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_CLK */
+	{OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_CMD */
+	{OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)},  /* MMC0_CD */
+	{-1},
+};
+
+/* MII pins */
+static struct module_pin_mux mii1_pin_mux[] = {
+	{OFFSET(mii1_rxerr), MODE(0) | RXACTIVE},	/* MII1_RXERR */
+	{OFFSET(mii1_txen), MODE(0)},			/* MII1_TXEN */
+	{OFFSET(mii1_rxdv), MODE(0) | RXACTIVE},	/* MII1_RXDV */
+	{OFFSET(mii1_txd3), MODE(0)},			/* MII1_TXD3 */
+	{OFFSET(mii1_txd2), MODE(0)},			/* MII1_TXD2 */
+	{OFFSET(mii1_txd1), MODE(0)},			/* MII1_TXD1 */
+	{OFFSET(mii1_txd0), MODE(0)},			/* MII1_TXD0 */
+	{OFFSET(mii1_txclk), MODE(0) | RXACTIVE},	/* MII1_TXCLK */
+	{OFFSET(mii1_rxclk), MODE(0) | RXACTIVE},	/* MII1_RXCLK */
+	{OFFSET(mii1_rxd3), MODE(0) | RXACTIVE},	/* MII1_RXD3 */
+	{OFFSET(mii1_rxd2), MODE(0) | RXACTIVE},	/* MII1_RXD2 */
+	{OFFSET(mii1_rxd1), MODE(0) | RXACTIVE},	/* MII1_RXD1 */
+	{OFFSET(mii1_rxd0), MODE(0) | RXACTIVE},	/* MII1_RXD0 */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+/* NAND pins */
+static struct module_pin_mux nand_pin_mux[] = {
+	{OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD0 */
+	{OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD1 */
+	{OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD2 */
+	{OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD3 */
+	{OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD4 */
+	{OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD5 */
+	{OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD6 */
+	{OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD7 */
+	{OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+	{OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)},	/* NAND_WPN */
+	{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)},	/* NAND_CS0 */
+	{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+	{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)},	/* NAND_OE */
+	{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)},	/* NAND_WEN */
+	{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)},	/* NAND_BE_CLE */
+	{-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_board_pin_mux()
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+	configure_module_pin_mux(uart0_pin_mux);
+	configure_module_pin_mux(mii1_pin_mux);
+	configure_module_pin_mux(mmc0_pin_mux);
+	configure_module_pin_mux(nand_pin_mux);
+}
diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c
index 4e6846a..95fd137 100644
--- a/board/ti/am43xx/board.c
+++ b/board/ti/am43xx/board.c
@@ -346,14 +346,14 @@ static void enable_vtt_regulator(void)
 	u32 temp;
 
 	/* enable module */
-	writel(GPIO_CTRL_ENABLEMODULE, AM33XX_GPIO0_BASE + OMAP_GPIO_CTRL);
-
-	/* enable output for GPIO0_22 */
-	writel(GPIO_SETDATAOUT(GPIO_22),
-	       AM33XX_GPIO0_BASE + OMAP_GPIO_SETDATAOUT);
-	temp = readl(AM33XX_GPIO0_BASE + OMAP_GPIO_OE);
-	temp = temp & ~(GPIO_OE_ENABLE(GPIO_22));
-	writel(temp, AM33XX_GPIO0_BASE + OMAP_GPIO_OE);
+	writel(GPIO_CTRL_ENABLEMODULE, AM33XX_GPIO5_BASE + OMAP_GPIO_CTRL);
+
+	/* enable output for GPIO5_7 */
+	writel(GPIO_SETDATAOUT(7),
+	       AM33XX_GPIO5_BASE + OMAP_GPIO_SETDATAOUT);
+	temp = readl(AM33XX_GPIO5_BASE + OMAP_GPIO_OE);
+	temp = temp & ~(GPIO_OE_ENABLE(7));
+	writel(temp, AM33XX_GPIO5_BASE + OMAP_GPIO_OE);
 }
 
 void sdram_init(void)
diff --git a/board/ti/am43xx/mux.c b/board/ti/am43xx/mux.c
index 810b194..51f7fd6 100644
--- a/board/ti/am43xx/mux.c
+++ b/board/ti/am43xx/mux.c
@@ -33,8 +33,8 @@ static struct module_pin_mux i2c0_pin_mux[] = {
 	{-1},
 };
 
-static struct module_pin_mux gpio0_22_pin_mux[] = {
-	{OFFSET(ddr_ba2), (MODE(9) | PULLUP_EN)},	/* GPIO0_22 */
+static struct module_pin_mux gpio5_7_pin_mux[] = {
+	{OFFSET(spi0_cs0), (MODE(7) | PULLUP_EN)},	/* GPIO5_7 */
 	{-1},
 };
 
@@ -49,7 +49,7 @@ void enable_board_pin_mux(void)
 	configure_module_pin_mux(i2c0_pin_mux);
 
 	if (board_is_gpevm())
-		configure_module_pin_mux(gpio0_22_pin_mux);
+		configure_module_pin_mux(gpio5_7_pin_mux);
 }
 
 void enable_i2c0_pin_mux(void)