ENGR00241595-2 mx6q-arm2:Enable SATA PHY PDDQ default

The SATA PHY PDDQ configuration is depended on the CONFIG_CMD_SATA
defined or not in board config file. If SATA feature is not config,
then the PDDQ will not be set, SATA PHY will not entry in Low Power
Mode, and it will consume some power even there is no sata devices
on board.
This patch:
1 Enable SATA PHY PDDQ default no matter the SATA is enabled or not in
  board config file, SATA module will disable PDDQ first when used phy,
  so default enable PDDQ will not affect SATA feature.
2 It needs a delay to wait for SATA PHY initialize after enable it,
  otherwise write the phy registers will fail.

Signed-off-by: Lin Fuzhen <fuzhen.lin@freescale.com>

1 files changed, 18 insertions, 18 deletions

diff --git a/board/freescale/mx6q_arm2/mx6q_arm2.c b/board/freescale/mx6q_arm2/mx6q_arm2.c
index 45388ee..a68720d 100644
--- a/board/freescale/mx6q_arm2/mx6q_arm2.c
+++ b/board/freescale/mx6q_arm2/mx6q_arm2.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2010-2012 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010-2013 Freescale Semiconductor, Inc.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -236,23 +236,21 @@ void board_mmu_init(void)
 }
 #endif
 
-#ifdef CONFIG_DWC_AHSATA
-
 #define ANATOP_PLL_LOCK                 0x80000000
 #define ANATOP_PLL_ENABLE_MASK          0x00002000
 #define ANATOP_PLL_BYPASS_MASK          0x00010000
-#define ANATOP_PLL_LOCK                 0x80000000
 #define ANATOP_PLL_PWDN_MASK            0x00001000
 #define ANATOP_PLL_HOLD_RING_OFF_MASK   0x00000800
 #define ANATOP_SATA_CLK_ENABLE_MASK     0x00100000
+#define	PORT_PHY_CTL                    0x178
+#define	PORT_PHY_CTL_PDDQ_LOC		    0x100000
 
+#ifdef CONFIG_DWC_AHSATA
 /* Staggered Spin-up */
 #define	HOST_CAP_SSS			(1 << 27)
 /* host version register*/
 #define	HOST_VERSIONR			0xfc
 #define PORT_SATA_SR			0x128
-#define	PORT_PHY_CTL			0x178
-#define	PORT_PHY_CTL_PDDQ_LOC		0x100000
 
 int sata_initialize(void)
 {
@@ -299,8 +297,9 @@ int sata_initialize(void)
 
 	return __sata_initialize();
 }
+#endif
 
-int setup_sata(void)
+static int setup_sata(void)
 {
 	u32 reg = 0;
 	s32 timeout = 100000;
@@ -343,17 +342,19 @@ int setup_sata(void)
 	 * */
 	reg |= 0x59124c6;
 	writel(reg, IOMUXC_BASE_ADDR + 0x34);
-
-	if (sata_curr_device == -1) {
-		/* Enable PDDQ mode in default if there isn't sata boot */
-		reg = readl(SATA_ARB_BASE_ADDR + PORT_PHY_CTL);
-		writel(reg | PORT_PHY_CTL_PDDQ_LOC,
-				SATA_ARB_BASE_ADDR + PORT_PHY_CTL);
-	}
+    /* FIXME */
+    /*
+     * It needs to wait SATA PHY initialize completed, otherwise write the
+     * PORT_PHY_CTL will fail, then can't enable PDDQ which let PHY entry LPM
+     * Currently set it as 1ms.
+     */
+	udelay(1000);
+	/* Enable PDDQ mode in default */
+    writel(readl(SATA_ARB_BASE_ADDR + PORT_PHY_CTL) | PORT_PHY_CTL_PDDQ_LOC,
+			SATA_ARB_BASE_ADDR + PORT_PHY_CTL);
 
 	return 0;
 }
-#endif
 
 int dram_init(void)
 {
@@ -1255,10 +1256,7 @@ int board_init(void)
 	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 
 	setup_uart();
-
-#ifdef CONFIG_DWC_AHSATA
 	setup_sata();
-#endif
 
 #ifdef CONFIG_VIDEO_MX5
 
@@ -1483,6 +1481,8 @@ int checkboard(void)
 	if (check_hab_enable() == 1)
 		get_hab_status();
 #endif
+    printf("SATA PDDQ: %s\n", ((readl(SATA_ARB_BASE_ADDR + PORT_PHY_CTL)
+			& PORT_PHY_CTL_PDDQ_LOC)>>20) ? "enabled" : "disabled");
 
 	return 0;
 }