OMAP: Remove omap1610inn-based boards

The CS_AUTOBOOT configurations have been broken for a long time.
Kshitij Gupta is no longer at TI making these broken and orphaned
boards, so remove.

Signed-off-by: Tom Rini <trini@ti.com>

5 files changed, 0 insertions, 1327 deletions

diff --git a/board/ti/omap1610inn/Makefile b/board/ti/omap1610inn/Makefile
deleted file mode 100644
index 2b8641f..0000000
--- a/board/ti/omap1610inn/Makefile
+++ /dev/null
@@ -1,45 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).o
-
-COBJS	:= omap1610innovator.o flash.o
-SOBJS	:= lowlevel_init.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/ti/omap1610inn/config.mk b/board/ti/omap1610inn/config.mk
deleted file mode 100644
index ee0aa0a..0000000
--- a/board/ti/omap1610inn/config.mk
+++ /dev/null
@@ -1,26 +0,0 @@
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# TI Innovator board with OMAP1610 (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# Innovator has 1 bank of 256 MB SDRAM
-# Physical Address:
-# 1000'0000 to 2000'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
-# (mem base + reserved)
-#
-# we load ourself to 1108'0000
-#
-#
-
-
-CONFIG_SYS_TEXT_BASE = 0x11080000
diff --git a/board/ti/omap1610inn/flash.c b/board/ti/omap1610inn/flash.c
deleted file mode 100644
index a99a91c..0000000
--- a/board/ti/omap1610inn/flash.c
+++ /dev/null
@@ -1,495 +0,0 @@
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2001-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-
-#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 256 KB sectors (x2) */
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];	/* info for FLASH chips	   */
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH		ushort
-#define FLASH_PORT_WIDTHV		vu_short
-#define SWAP(x)			__swab16(x)
-#else
-#define FLASH_PORT_WIDTH		ulong
-#define FLASH_PORT_WIDTHV		vu_long
-#define SWAP(x)			__swab32(x)
-#endif
-
-#define FPW	FLASH_PORT_WIDTH
-#define FPWV	FLASH_PORT_WIDTHV
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-
-/* Flash Organization Structure */
-typedef struct OrgDef {
-	unsigned int sector_number;
-	unsigned int sector_size;
-} OrgDef;
-
-
-/* Flash Organizations */
-OrgDef OrgIntel_28F256L18T[] = {
-	{4, 32 * 1024},				/* 4 * 32kBytes sectors */
-	{255, 128 * 1024},			/* 255 * 128kBytes sectors */
-};
-
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-unsigned long flash_init (void);
-static ulong flash_get_size (FPW * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-void inline spin_wheel (void);
-void flash_print_info (flash_info_t * info);
-void flash_unprotect_sectors (FPWV * addr);
-int flash_erase (flash_info_t * info, int s_first, int s_last);
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
-void flash_unlock(flash_info_t * info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	int i;
-	ulong size = 0;
-
-	for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
-		switch (i) {
-		case 0:
-			flash_get_size ((FPW *) CONFIG_SYS_FLASH_BASE, &flash_info[i]);
-			flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[i]);
-			/* to reset the lock bit */
-			flash_unlock(&flash_info[i]);
-			break;
-		default:
-			panic ("configured too many flash banks!\n");
-			break;
-		}
-		size += flash_info[i].size;
-	}
-
-	/* Protect monitor and environment sectors
-	 */
-	flash_protect (FLAG_PROTECT_SET,
-			CONFIG_SYS_FLASH_BASE,
-			CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
-
-	flash_protect (FLAG_PROTECT_SET,
-			CONFIG_ENV_ADDR,
-			CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-
-	return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_unlock(flash_info_t * info)
-{
-	int j;
-	for (j=2;j<CONFIG_SYS_MAX_FLASH_SECT;j++){
-	FPWV *addr = (FPWV *) (info->start[j]);
-	flash_unprotect_sectors (addr);
-	*addr = (FPW) 0x00500050;/* clear status register */
-	*addr = (FPW) 0x00FF00FF;/* resest to read mode */
-	}
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return;
-	}
-
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
-		for (i = 0; i < info->sector_count; i++) {
-			if (i > 255) {
-				info->start[i] = base + (i * 0x8000);
-				info->protect[i] = 0;
-			} else {
-				info->start[i] = base +
-						(i * PHYS_FLASH_SECT_SIZE);
-				info->protect[i] = 0;
-			}
-		}
-	}
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_INTEL:
-		printf ("INTEL ");
-		break;
-	default:
-		printf ("Unknown Vendor ");
-		break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_28F256L18T:
-		printf ("FLASH 28F256L18T\n");
-		break;
-	default:
-		printf ("Unknown Chip Type\n");
-		break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-			info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i = 0; i < info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i], info->protect[i] ? " (RO)" : "	   ");
-	}
-	printf ("\n");
-	return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info)
-{
-	volatile FPW value;
-
-	/* Write auto select command: read Manufacturer ID */
-	addr[0x5555] = (FPW) 0x00AA00AA;
-	addr[0x2AAA] = (FPW) 0x00550055;
-	addr[0x5555] = (FPW) 0x00900090;
-
-	mb ();
-	value = addr[0];
-
-	switch (value) {
-
-	case (FPW) INTEL_MANUFACT:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
-		return (0);		/* no or unknown flash	*/
-	}
-
-	mb ();
-	value = addr[1];	/* device ID	    */
-	switch (value) {
-
-	case (FPW) (INTEL_ID_28F256L18T):
-		info->flash_id += FLASH_28F256L18T;
-		info->sector_count = 259;
-		info->size = 0x02000000;
-		break;			/* => 32 MB	*/
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		break;
-	}
-
-	if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
-		printf ("** ERROR: sector count %d > max (%d) **\n",
-				info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
-		info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
-	}
-
-	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
-
-	return (info->size);
-}
-
-
-/* unprotects a sector for write and erase
- * on some intel parts, this unprotects the entire chip, but it
- * wont hurt to call this additional times per sector...
- */
-void flash_unprotect_sectors (FPWV * addr)
-{
-#define PD_FINTEL_WSMS_READY_MASK    0x0080
-
-	*addr = (FPW) 0x00500050;	/* clear status register */
-
-	/* this sends the clear lock bit command */
-	*addr = (FPW) 0x00600060;
-	*addr = (FPW) 0x00D000D0;
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
-	int flag, prot, sect;
-	ulong type, start;
-	int rcode = 0;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	type = (info->flash_id & FLASH_VENDMASK);
-	if ((type != FLASH_MAN_INTEL)) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-				info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect = s_first; sect <= s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-				prot);
-	} else {
-		printf ("\n");
-	}
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect <= s_last; sect++) {
-		if (info->protect[sect] == 0) { /* not protected */
-			FPWV *addr = (FPWV *) (info->start[sect]);
-			FPW status;
-
-			printf ("Erasing sector %2d ... ", sect);
-
-			flash_unprotect_sectors (addr);
-
-			/* arm simple, non interrupt dependent timer */
-			start = get_timer(0);
-
-			*addr = (FPW) 0x00500050;/* clear status register */
-			*addr = (FPW) 0x00200020;/* erase setup */
-			*addr = (FPW) 0x00D000D0;/* erase confirm */
-
-			while (((status =
-				*addr) & (FPW) 0x00800080) !=
-				(FPW) 0x00800080) {
-					if (get_timer(start) >
-					CONFIG_SYS_FLASH_ERASE_TOUT) {
-					printf ("Timeout\n");
-					/* suspend erase     */
-					*addr = (FPW) 0x00B000B0;
-					/* reset to read mode */
-					*addr = (FPW) 0x00FF00FF;
-					rcode = 1;
-					break;
-				}
-			}
-
-			/* clear status register cmd.	*/
-			*addr = (FPW) 0x00500050;
-			*addr = (FPW) 0x00FF00FF;/* resest to read mode */
-			printf (" done\n");
-		}
-	}
-	if (flag)
-		enable_interrupts();
-
-	return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
-	ulong cp, wp;
-	FPW data;
-	int count, i, l, rc, port_width;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return 4;
-	}
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
-	wp = (addr & ~1);
-	port_width = 2;
-#else
-	wp = (addr & ~3);
-	port_width = 4;
-#endif
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i = 0, cp = wp; i < l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-		for (; i < port_width && cnt > 0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt == 0 && i < port_width; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-
-		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	count = 0;
-	while (cnt >= port_width) {
-		data = 0;
-		for (i = 0; i < port_width; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-		cnt -= port_width;
-		if (count++ > 0x800) {
-			spin_wheel ();
-			count = 0;
-		}
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i < port_width; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *) cp);
-	}
-
-	return (write_data (info, wp, SWAP (data)));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
-	FPWV *addr = (FPWV *) dest;
-	ulong status;
-	int flag, rc = 0;
-	ulong start;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*addr & data) != data) {
-		printf("not erased at %08lx (%x)\n", (ulong) addr, *addr);
-		return 2;
-	}
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-	*addr = (FPW) 0x00400040;	/* write setup */
-	*addr = data;
-
-	/* arm simple, non interrupt dependent timer */
-	start = get_timer(0);
-
-	/* wait while polling the status register */
-	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
-		if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-			rc = 1;
-			goto done;
-		}
-	}
-done:
-	if (flag)
-		enable_interrupts();
-
-	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
-	return rc;
-}
-
-void inline spin_wheel (void)
-{
-	static int p = 0;
-	static char w[] = "\\/-";
-
-	printf ("\010%c", w[p]);
-	(++p == 3) ? (p = 0) : 0;
-}
diff --git a/board/ti/omap1610inn/lowlevel_init.S b/board/ti/omap1610inn/lowlevel_init.S
deleted file mode 100644
index b376ba5..0000000
--- a/board/ti/omap1610inn/lowlevel_init.S
+++ /dev/null
@@ -1,452 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-
-_TEXT_BASE:
-	.word	CONFIG_SYS_TEXT_BASE	/* sdram load addr from config.mk */
-
-.globl lowlevel_init
-lowlevel_init:
-
-
-	/*------------------------------------------------------*
-	 *mask all IRQs by setting all bits in the INTMR default*
-	 *------------------------------------------------------*/
-	mov	r1, #0xffffffff
-	ldr	r0, =REG_IHL1_MIR
-	str	r1, [r0]
-	ldr	r0, =REG_IHL2_MIR
-	str	r1, [r0]
-
-	/*------------------------------------------------------*
-	 * Set up ARM CLM registers (IDLECT1)                   *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_ARM_IDLECT1
-	ldr	r1,	VAL_ARM_IDLECT1
-	str	r1,	[r0]
-
-	/*------------------------------------------------------*
-	 * Set up ARM CLM registers (IDLECT2)		        *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_ARM_IDLECT2
-	ldr	r1,	VAL_ARM_IDLECT2
-	str	r1,	[r0]
-
-	/*------------------------------------------------------*
-	 * Set up ARM CLM registers (IDLECT3)		        *
-	 *------------------------------------------------------*/
-	ldr	r0,	REG_ARM_IDLECT3
-	ldr	r1,	VAL_ARM_IDLECT3
-	str	r1,	[r0]
-
-#ifdef CONFIG_CS_AUTOBOOT		/* do the setup depending on boot mode */
-	ldr	r0, CONF_STATUS
-	ldr	r1, [r0]
-	tst	r1, #0x02
-	beq	disable_wd		/* booting from RAM, skip setup */
-#endif
-
-	mov	r1,	#0x01		/* PER_EN bit */
-	ldr	r0,	REG_ARM_RSTCT2
-	strh	r1,	[r0]		/* CLKM; Peripheral reset. */
-
-	/* Set CLKM to Sync-Scalable	*/
-	/* I supposedly need to enable the dsp clock before switching */
-	mov	r1,	#0x0000
-	ldr	r0,	REG_ARM_SYSST
-	strh	r1,	[r0]
-	mov	r0,	#0x400
-1:
-	subs	r0,	r0,	#0x1	/* wait for any bubbles to finish */
-	bne	1b
-	ldr	r1,	VAL_ARM_CKCTL
-	ldr	r0,	REG_ARM_CKCTL
-	strh	r1,	[r0]
-
-	/* a few nops to let settle */
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-
-	/* setup DPLL 1 */
-	/* Ramp up the clock to 96Mhz */
-	ldr	r1,	VAL_DPLL1_CTL
-	ldr	r0,	REG_DPLL1_CTL
-	strh	r1,	[r0]
-	ands	r1,	r1,	#0x10	/* Check if PLL is enabled. */
-	beq	lock_end	/* Do not look for lock if BYPASS selected */
-2:
-	ldrh	r1,	[r0]
-	ands	r1,	r1,	#0x01	/*	Check the LOCK bit.*/
-	beq 2b			/*	loop until bit goes hi. */
-lock_end:
-
-
-	/*------------------------------------------------------*
-	 * Turn off the watchdog during init...			*
-	 *------------------------------------------------------*/
-disable_wd:
-	ldr	r0,	REG_WATCHDOG
-	ldr	r1,	WATCHDOG_VAL1
-	str	r1,	[r0]
-	ldr	r1,	WATCHDOG_VAL2
-	str	r1,	[r0]
-	ldr	r0,	REG_WSPRDOG
-	ldr	r1,	WSPRDOG_VAL1
-	str	r1,	[r0]
-	ldr	r0,	REG_WWPSDOG
-
-watch1Wait:
-	ldr	r1,	[r0]
-	tst	r1,	#0x10
-	bne	watch1Wait
-
-	ldr	r0,	REG_WSPRDOG
-	ldr	r1,	WSPRDOG_VAL2
-	str	r1,	[r0]
-	ldr	r0,	REG_WWPSDOG
-watch2Wait:
-	ldr	r1,	[r0]
-	tst	r1,	#0x10
-	bne	watch2Wait
-
-
-	/* Set memory timings corresponding to the new clock speed */
-
-	/* Check execution location to determine current execution location
-	 * and branch to appropriate initialization code.
-	 */
-	/* Load physical SDRAM base. */
-	mov	r0,	#0x10000000
-	/* Get current execution location. */
-	mov	r1,	pc
-	/* Compare. */
-	cmp	r1,	r0
-	/* Skip over EMIF-fast initialization if running from SDRAM. */
-	bge	skip_sdram
-
-	/*
-	* Delay for SDRAM initialization.
-	*/
-	mov	r3,	#0x1800		/* value should be checked */
-3:
-	subs	r3,	r3,	#0x1	/* Decrement count */
-	bne	3b
-
-
-	/*
-	 * Set SDRAM control values. Disable refresh before MRS command.
-	 */
-
-	/* mobile ddr operation */
-	ldr	r0,	REG_SDRAM_OPERATION
-	mov	r2,	#07
-	str	r2,	[r0]
-
-	/* config register */
-	ldr	r0,	REG_SDRAM_CONFIG
-	ldr	r1,	SDRAM_CONFIG_VAL
-	str	r1,	[r0]
-
-	/* manual command register */
-	ldr	r0,	REG_SDRAM_MANUAL_CMD
-	/* issue set cke high */
-	mov	r1,	#CMD_SDRAM_CKE_SET_HIGH
-	str	r1,	[r0]
-	/* issue nop */
-	mov	r1,	#CMD_SDRAM_NOP
-	str	r1,	[r0]
-
-	mov	r2,	#0x0100
-waitMDDR1:
-	subs	r2,	r2,	 #1
-	bne	waitMDDR1	/* delay loop */
-
-	/* issue precharge */
-	mov	r1,	#CMD_SDRAM_PRECHARGE
-	str	r1,	[r0]
-
-	/* issue autorefresh x 2 */
-	mov	r1,	#CMD_SDRAM_AUTOREFRESH
-	str	r1,	[r0]
-	str	r1,	[r0]
-
-	/* mrs register ddr mobile */
-	ldr	r0,	REG_SDRAM_MRS
-	mov	r1,	#0x33
-	str	r1,	[r0]
-
-	/* emrs1 low-power register */
-	ldr	r0,	REG_SDRAM_EMRS1
-	/* self refresh on all banks */
-	mov	r1,	#0
-	str	r1,	[r0]
-
-	ldr	r0,	REG_DLL_URD_CONTROL
-	ldr	r1,	DLL_URD_CONTROL_VAL
-	str	r1,	[r0]
-
-	ldr	r0,	REG_DLL_LRD_CONTROL
-	ldr	r1,	DLL_LRD_CONTROL_VAL
-	str	r1,	[r0]
-
-	ldr	r0,	REG_DLL_WRT_CONTROL
-	ldr	r1,	DLL_WRT_CONTROL_VAL
-	str	r1,	[r0]
-
-	/* delay loop */
-	mov	r2,	#0x0100
-waitMDDR2:
-	subs	r2,	r2,	#1
-	bne	waitMDDR2
-
-	/*
-	 * Delay for SDRAM initialization.
-	 */
-	mov	r3,	#0x1800
-4:
-	subs	r3,	r3,	#1	/* Decrement count. */
-	bne	4b
-	b	common_tc
-
-skip_sdram:
-
-	ldr	r0,	REG_SDRAM_CONFIG
-	ldr	r1,	SDRAM_CONFIG_VAL
-	str	r1,	[r0]
-
-common_tc:
-	/* slow interface */
-	ldr	r1,	VAL_TC_EMIFS_CS0_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS0_CONFIG
-	str	r1,	[r0] /* Chip Select 0 */
-
-	ldr	r1,	VAL_TC_EMIFS_CS1_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS1_CONFIG
-	str	r1,	[r0] /* Chip Select 1 */
-	ldr	r1,	VAL_TC_EMIFS_CS3_CONFIG
-	ldr	r0,	REG_TC_EMIFS_CS3_CONFIG
-	str	r1,	[r0] /* Chip Select 3 */
-
-#ifdef CONFIG_H2_OMAP1610
-	/* inserting additional 2 clock cycle hold time for LAN */
-	ldr     r0,     REG_TC_EMIFS_CS1_ADVANCED
-	ldr	r1,     VAL_TC_EMIFS_CS1_ADVANCED
-	str     r1,     [r0]
-#endif
-	/* Start MPU Timer 1 */
-	ldr	r0,	REG_MPU_LOAD_TIMER
-	ldr	r1,	VAL_MPU_LOAD_TIMER
-	str	r1,	[r0]
-
-	ldr	r0,	REG_MPU_CNTL_TIMER
-	ldr	r1,	VAL_MPU_CNTL_TIMER
-	str	r1,	[r0]
-
-	/* back to arch calling code */
-	mov	pc,	lr
-
-	/* the literal pools origin */
-	.ltorg
-
-#ifdef CONFIG_CS_AUTOBOOT
-CONF_STATUS:
-	.word 0xfffe1130	/* 32 bits */
-#endif
-
-REG_TC_EMIFS_CONFIG:		/* 32 bits */
-	.word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG:	/* 32 bits */
-	.word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG:	/* 32 bits */
-	.word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG:	/* 32 bits */
-	.word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG:	/* 32 bits */
-	.word 0xfffecc1c
-
-#ifdef CONFIG_H2_OMAP1610
-REG_TC_EMIFS_CS1_ADVANCED:	/* 32 bits */
-	.word 0xfffecc54
-#endif
-
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL:			/* 16 bits */
-	.word 0xfffece00
-
-REG_ARM_IDLECT3:		/* 16 bits */
-	.word 0xfffece24
-REG_ARM_IDLECT2:		/* 16 bits */
-	.word 0xfffece08
-REG_ARM_IDLECT1:		/* 16 bits */
-	.word 0xfffece04
-
-REG_ARM_RSTCT2:			/* 16 bits */
-	.word 0xfffece14
-REG_ARM_SYSST:			/* 16 bits */
-	.word 0xfffece18
-/* DPLL control registers */
-REG_DPLL1_CTL:			/* 16 bits */
-	.word 0xfffecf00
-
-/* Watch Dog register */
-/* secure watchdog stop */
-REG_WSPRDOG:
-	.word 0xfffeb048
-/* watchdog write pending */
-REG_WWPSDOG:
-	.word 0xfffeb034
-
-WSPRDOG_VAL1:
-	.word 0x0000aaaa
-WSPRDOG_VAL2:
-	.word 0x00005555
-
-/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
- counter @8192 rows, 10 ns, 8 burst */
-REG_SDRAM_CONFIG:
-	.word 0xfffecc20
-
-/* Operation register */
-REG_SDRAM_OPERATION:
-	.word 0xfffecc80
-
-/* Manual command register */
-REG_SDRAM_MANUAL_CMD:
-	.word 0xfffecc84
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_MRS:
-	.word 0xfffecc70
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_EMRS1:
-	.word 0xfffecc78
-
-/* WRT DLL register */
-REG_DLL_WRT_CONTROL:
-	.word 0xfffecc68
-DLL_WRT_CONTROL_VAL:
-	.word 0x03f00002
-
-/* URD DLL register */
-REG_DLL_URD_CONTROL:
-	.word 0xfffeccc0
-DLL_URD_CONTROL_VAL:
-	.word 0x00800002
-
-/* LRD DLL register */
-REG_DLL_LRD_CONTROL:
-	.word 0xfffecccc
-
-REG_WATCHDOG:
-	.word 0xfffec808
-
-REG_MPU_LOAD_TIMER:
-	.word 0xfffec504
-REG_MPU_CNTL_TIMER:
-	.word 0xfffec500
-
-/* 96 MHz Samsung Mobile DDR */
-SDRAM_CONFIG_VAL:
-	.word 0x001200f4
-
-DLL_LRD_CONTROL_VAL:
-	.word 0x00800002
-
-VAL_ARM_CKCTL:
-	.word 0x3000
-VAL_DPLL1_CTL:
-	.word 0x2830
-
-#ifdef CONFIG_INNOVATOROMAP1610
-VAL_TC_EMIFS_CS0_CONFIG:
-	.word 0x002130b0
-VAL_TC_EMIFS_CS1_CONFIG:
-	.word 0x00001131
-VAL_TC_EMIFS_CS2_CONFIG:
-	.word 0x000055f0
-VAL_TC_EMIFS_CS3_CONFIG:
-	.word 0x88011131
-#endif
-
-#ifdef CONFIG_H2_OMAP1610
-VAL_TC_EMIFS_CS0_CONFIG:
-	.word 0x00203331
-VAL_TC_EMIFS_CS1_CONFIG:
-	.word 0x8180fff3
-VAL_TC_EMIFS_CS2_CONFIG:
-	.word 0xf800f22a
-VAL_TC_EMIFS_CS3_CONFIG:
-	.word 0x88011131
-VAL_TC_EMIFS_CS1_ADVANCED:
-	.word 0x00000022
-#endif
-
-VAL_TC_EMIFF_SDRAM_CONFIG:
-	.word 0x010290fc
-VAL_TC_EMIFF_MRS:
-	.word 0x00000027
-
-VAL_ARM_IDLECT1:
-	.word 0x00000400
-
-VAL_ARM_IDLECT2:
-	.word 0x00000886
-VAL_ARM_IDLECT3:
-	.word 0x00000015
-
-WATCHDOG_VAL1:
-	.word 0x000000f5
-WATCHDOG_VAL2:
-	.word 0x000000a0
-
-VAL_MPU_LOAD_TIMER:
-	.word 0xffffffff
-VAL_MPU_CNTL_TIMER:
-	.word 0xffffffa1
-
-/* command values */
-.equ CMD_SDRAM_NOP,		0x00000000
-.equ CMD_SDRAM_PRECHARGE,	0x00000001
-.equ CMD_SDRAM_AUTOREFRESH,	0x00000002
-.equ CMD_SDRAM_CKE_SET_HIGH,	0x00000007
diff --git a/board/ti/omap1610inn/omap1610innovator.c b/board/ti/omap1610inn/omap1610innovator.c
deleted file mode 100644
index 16e8237..0000000
--- a/board/ti/omap1610inn/omap1610innovator.c
+++ /dev/null
@@ -1,309 +0,0 @@
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_CS_AUTOBOOT
-unsigned long omap_flash_base;
-#endif
-
-void flash__init (void);
-void ether__init (void);
-void set_muxconf_regs (void);
-void peripheral_power_enable (void);
-
-#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
-
-static inline void delay (unsigned long loops)
-{
-	__asm__ volatile ("1:\n"
-		"subs %0, %1, #1\n"
-		"bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x10000100;
-
-	/* Configure MUX settings */
-	set_muxconf_regs ();
-	peripheral_power_enable ();
-
-/* this speeds up your boot a quite a bit.  However to make it
- *  work, you need make sure your kernel startup flush bug is fixed.
- *  ... rkw ...
- */
-	icache_enable ();
-
-	flash__init ();
-	ether__init ();
-	return 0;
-}
-
-
-int misc_init_r (void)
-{
-	/* currently empty */
-	return (0);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-void flash__init (void)
-{
-#define EMIFS_GlB_Config_REG 0xfffecc0c
-	unsigned int regval;
-
-#ifdef CONFIG_CS_AUTOBOOT
-	 /* Check swapping of CS0 and CS3, set flash base accordingly */
-	omap_flash_base = ((*((u32 *)OMAP_EMIFS_CONFIG_REG) & 0x02) == 0) ?
-					PHYS_FLASH_1_BM0 : PHYS_FLASH_1_BM1;
-#endif
-	regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
-	/* Turn off write protection for flash devices. */
-	regval = regval | 0x0001;
-	*((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
-}
-/*************************************************************
- Routine:ether__init
- Description: take the Ethernet controller out of reset and wait
-			   for the EEPROM load to complete.
-*************************************************************/
-void ether__init (void)
-{
-#define ETH_CONTROL_REG 0x0400030b
-
-#ifdef CONFIG_H2_OMAP1610
-	#define LAN_RESET_REGISTER 0x0400001c
-
-	/* The debug board on which the lan chip resides may not be powered
-	 * ON at the same time as the OMAP chip. So wait in a loop until the
-	 * lan reset register (on the debug board) is available (powered on)
-	 * and reset the lan chip.
-	 */
-
-	*((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
-	do {
-		*((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001;
-		udelay (3);
-	} while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001);
-
-	do {
-		*((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
-		udelay (3);
-	} while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000);
-#endif
-
-	*((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
-	udelay (3);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-int dram_init (void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
-}
-
-/******************************************************
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers
-			  specific to the hardware
-*******************************************************/
-void set_muxconf_regs (void)
-{
-	volatile unsigned int *MuxConfReg;
-	/* set each registers to its reset value; */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
-	/* setup for UART1 */
-	*MuxConfReg &= ~(0x02000000);	/* bit 25 */
-	/* setup for UART2 */
-	*MuxConfReg &= ~(0x01000000);	/* bit 24 */
-	/* Disable Uwire CS Hi-Z */
-	*MuxConfReg |= 0x08000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6);
-	/*setup mux for UART3 */
-	*MuxConfReg |= 0x00000001;	/* bit3, 1, 0 (mux0 5,5,26) */
-	*MuxConfReg &= ~0x0000003e;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8);
-	/* Disable Uwire CS Hi-Z */
-	*MuxConfReg |= 0x00001200;	/*bit 9 for CS0 12 for CS3 */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9);
-	/*  Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the  */
-	/*  hardware will actually use TX and RTS based on bit 25 in  */
-	/*  FUNC_MUX_CTRL_0.  I told you this thing was screwy!  */
-	*MuxConfReg |= 0x00201000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C);
-	/* setup for UART2 */
-	/*  Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the  */
-	/*  hardware will actually use TX and RTS based on bit 24 in  */
-	/*  FUNC_MUX_CTRL_0. */
-	*MuxConfReg |= 0x09000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1);
-	*MuxConfReg = 0x00000000;
-	/* mux setup for SD/MMC driver */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2);
-	*MuxConfReg &= 0xFFFE0FFF;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
-	/* bit 13 for MMC2 XOR_CLK */
-	*MuxConfReg &= ~(0x00002000);
-	/* bit 29 for UART 1 */
-	*MuxConfReg &= ~(0x00002000);
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
-	/* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */
-	*MuxConfReg |= 0x000C0000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL);
-	*MuxConfReg &= ~(0x00000070);
-	*MuxConfReg &= ~(0x00000008);
-	*MuxConfReg |= 0x00000003;
-	*MuxConfReg |= 0x00000180;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
-	/* bit 17, software controls VBUS */
-	*MuxConfReg &= ~(0x00020000);
-	/* Enable USB 48 and 12M clocks */
-	*MuxConfReg |= 0x00000200;
-	*MuxConfReg &= ~(0x00000180);
-	/*2.75V for MMCSDIO1 */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0);
-	*MuxConfReg = 0x00001FE7;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_0);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_1);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_3);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_4);
-	*MuxConfReg = 0x00000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4);
-	*MuxConfReg = 0x00000000;
-	/* Turn on UART2 48 MHZ clock */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
-	*MuxConfReg |= 0x40000000;
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) USB_OTG_CTRL);
-	/* setup for USB VBus detection OMAP161x */
-	*MuxConfReg |= 0x00040000;	/* bit 18 */
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
-	/* PullUps for SD/MMC driver */
-	*MuxConfReg |= ~(0xFFFE0FFF);
-	MuxConfReg =
-		(volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0);
-	*MuxConfReg = COMP_MODE_ENABLE;
-}
-
-/******************************************************
- Routine: peripheral_power_enable
- Description: Enable the power for UART1
-*******************************************************/
-void peripheral_power_enable (void)
-{
-#define UART1_48MHZ_ENABLE	((unsigned short)0x0200)
-#define SW_CLOCK_REQUEST	((volatile unsigned short *)0xFFFE0834)
-
-	*SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_LAN91C96
-	rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
-#endif
-	return rc;
-}
-#endif