Merge remote-tracking branch 'u-boot/master'

Conflicts:
	boards.cfg

Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).

68 files changed, 2008 insertions, 779 deletions

diff --git a/board/amcc/acadia/acadia.c b/board/amcc/acadia/acadia.c
index 9c6deea..2eb18df 100644
--- a/board/amcc/acadia/acadia.c
+++ b/board/amcc/acadia/acadia.c
@@ -39,12 +39,10 @@ int board_early_init_f(void)
 {
 	unsigned int reg;
 
-#if !defined(CONFIG_NAND_U_BOOT)
 	/* don't reinit PLL when booting via I2C bootstrap option */
 	mfsdr(SDR0_PINSTP, reg);
 	if (reg != 0xf0000000)
 		board_pll_init_f();
-#endif
 
 	acadia_gpio_init();
 
diff --git a/board/amcc/acadia/u-boot-nand.lds b/board/amcc/acadia/u-boot-nand.lds
deleted file mode 100644
index 9a331c5..0000000
--- a/board/amcc/acadia/u-boot-nand.lds
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- * (C) Copyright 2007
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .text      :
-  {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
-    arch/powerpc/cpu/ppc4xx/start.o	(.text*)
-
-    /* Align to next NAND block */
-    . = ALIGN(0x4000);
-    common/env_embedded.o  (.ppcenv)
-    /* Keep some space here for redundant env and potential bad env blocks */
-    . = ALIGN(0x10000);
-
-    *(.text*)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    KEEP(*(.got))
-    _GOT2_TABLE_ = .;
-    KEEP(*(.got2))
-    _FIXUP_TABLE_ = .;
-    KEEP(*(.fixup))
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data*)
-    *(.sdata*)
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.bss*)
-   *(.sbss*)
-   *(COMMON)
-   . = ALIGN(4);
-  }
-
-  __bss_end = . ;
-  PROVIDE (end = .);
-}
diff --git a/board/amcc/bamboo/u-boot-nand.lds b/board/amcc/bamboo/u-boot-nand.lds
deleted file mode 100644
index 5e84369..0000000
--- a/board/amcc/bamboo/u-boot-nand.lds
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
- * (C) Copyright 2007
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .text      :
-  {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
-    arch/powerpc/cpu/ppc4xx/start.o	(.text*)
-    board/amcc/bamboo/init.o		(.text*)
-
-    /* Align to next NAND block */
-    . = ALIGN(0x4000);
-    common/env_embedded.o  (.ppcenv)
-    /* Keep some space here for redundant env and potential bad env blocks */
-    . = ALIGN(0x10000);
-
-    *(.text*)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    KEEP(*(.got))
-    _GOT2_TABLE_ = .;
-    KEEP(*(.got2))
-    _FIXUP_TABLE_ = .;
-    KEEP(*(.fixup))
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data*)
-    *(.sdata*)
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.bss*)
-   *(.sbss*)
-   *(COMMON)
-   . = ALIGN(4);
-  }
-
-  __bss_end = . ;
-  PROVIDE (end = .);
-}
diff --git a/board/amcc/canyonlands/u-boot-nand.lds b/board/amcc/canyonlands/u-boot-nand.lds
deleted file mode 100644
index 31a2123..0000000
--- a/board/amcc/canyonlands/u-boot-nand.lds
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
- * (C) Copyright 2008
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .text      :
-  {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
-    arch/powerpc/cpu/ppc4xx/start.o	(.text)
-    board/amcc/canyonlands/init.o	(.text*)
-
-    /* Align to next NAND block */
-    . = ALIGN(0x20000);
-    common/env_embedded.o  (.ppcenv)
-    /* Keep some space here for redundant env and potential bad env blocks */
-    . = ALIGN(0x80000);
-
-    *(.text*)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    KEEP(*(.got))
-    _GOT2_TABLE_ = .;
-    KEEP(*(.got2))
-    _FIXUP_TABLE_ = .;
-    KEEP(*(.fixup))
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data*)
-    *(.sdata*)
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.bss*)
-   *(.sbss*)
-   *(COMMON)
-   . = ALIGN(4);
-  }
-
-  __bss_end = . ;
-  PROVIDE (end = .);
-}
diff --git a/board/amcc/kilauea/u-boot-nand.lds b/board/amcc/kilauea/u-boot-nand.lds
deleted file mode 100644
index 9a331c5..0000000
--- a/board/amcc/kilauea/u-boot-nand.lds
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- * (C) Copyright 2007
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .text      :
-  {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
-    arch/powerpc/cpu/ppc4xx/start.o	(.text*)
-
-    /* Align to next NAND block */
-    . = ALIGN(0x4000);
-    common/env_embedded.o  (.ppcenv)
-    /* Keep some space here for redundant env and potential bad env blocks */
-    . = ALIGN(0x10000);
-
-    *(.text*)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    KEEP(*(.got))
-    _GOT2_TABLE_ = .;
-    KEEP(*(.got2))
-    _FIXUP_TABLE_ = .;
-    KEEP(*(.fixup))
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data*)
-    *(.sdata*)
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.bss*)
-   *(.sbss*)
-   *(COMMON)
-   . = ALIGN(4);
-  }
-
-  __bss_end = . ;
-  PROVIDE (end = .);
-}
diff --git a/board/amcc/sequoia/u-boot-nand.lds b/board/amcc/sequoia/u-boot-nand.lds
deleted file mode 100644
index f4d752c..0000000
--- a/board/amcc/sequoia/u-boot-nand.lds
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
- * (C) Copyright 2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .text      :
-  {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
-    arch/powerpc/cpu/ppc4xx/start.o	(.text)
-    board/amcc/sequoia/init.o	(.text*)
-
-    /* Align to next NAND block */
-    . = ALIGN(0x4000);
-    common/env_embedded.o  (.ppcenv)
-    /* Keep some space here for redundant env and potential bad env blocks */
-    . = ALIGN(0x10000);
-
-    *(.text*)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    KEEP(*(.got))
-    _GOT2_TABLE_ = .;
-    KEEP(*(.got2))
-    _FIXUP_TABLE_ = .;
-    KEEP(*(.fixup))
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data*)
-    *(.sdata*)
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.bss*)
-   *(.sbss*)
-   *(COMMON)
-   . = ALIGN(4);
-  }
-
-  __bss_end = . ;
-  PROVIDE (end = .);
-}
diff --git a/board/armadeus/apf27/fpga.c b/board/armadeus/apf27/fpga.c
index 0c08c06..65a4812 100644
--- a/board/armadeus/apf27/fpga.c
+++ b/board/armadeus/apf27/fpga.c
@@ -26,7 +26,7 @@
  * Spartan2 code is used to download our Spartan 3 :) code is compatible.
  * Just take care about the file size
  */
-Xilinx_Spartan3_Slave_Parallel_fns fpga_fns = {
+xilinx_spartan3_slave_parallel_fns fpga_fns = {
 	fpga_pre_fn,
 	fpga_pgm_fn,
 	fpga_init_fn,
@@ -42,12 +42,13 @@ Xilinx_Spartan3_Slave_Parallel_fns fpga_fns = {
 	fpga_post_fn,
 };
 
-Xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
-	{Xilinx_Spartan3,
+xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
+	{xilinx_spartan3,
 	 slave_parallel,
 	 1196128l/8,
 	 (void *)&fpga_fns,
 	 0,
+	 &spartan3_op,
 	 "3s200aft256"}
 };
 
diff --git a/board/astro/mcf5373l/fpga.c b/board/astro/mcf5373l/fpga.c
index c679ad7..1d044d9 100644
--- a/board/astro/mcf5373l/fpga.c
+++ b/board/astro/mcf5373l/fpga.c
@@ -203,7 +203,7 @@ int astro5373l_altera_load(void)
 }
 
 /* Set the FPGA's PROG_B line to the specified level */
-int xilinx_pgm_fn(int assert, int flush, int cookie)
+int xilinx_pgm_config_fn(int assert, int flush, int cookie)
 {
 	gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
 
@@ -218,7 +218,7 @@ int xilinx_pgm_fn(int assert, int flush, int cookie)
  * Test the state of the active-low FPGA INIT line.  Return 1 on INIT
  * asserted (low).
  */
-int xilinx_init_fn(int cookie)
+int xilinx_init_config_fn(int cookie)
 {
 	gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
 
@@ -226,7 +226,7 @@ int xilinx_init_fn(int cookie)
 }
 
 /* Test the state of the active-high FPGA DONE pin */
-int xilinx_done_fn(int cookie)
+int xilinx_done_config_fn(int cookie)
 {
 	gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
 
@@ -234,7 +234,7 @@ int xilinx_done_fn(int cookie)
 }
 
 /* Abort an FPGA operation */
-int xilinx_abort_fn(int cookie)
+int xilinx_abort_config_fn(int cookie)
 {
 	gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
 	/* ensure all SPI peripherals and FPGAs are deselected */
@@ -300,7 +300,7 @@ int xilinx_post_config_fn(int cookie)
 	return rc;
 }
 
-int xilinx_clk_fn(int assert_clk, int flush, int cookie)
+int xilinx_clk_config_fn(int assert_clk, int flush, int cookie)
 {
 	gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
 
@@ -311,7 +311,7 @@ int xilinx_clk_fn(int assert_clk, int flush, int cookie)
 	return assert_clk;
 }
 
-int xilinx_wr_fn(int assert_write, int flush, int cookie)
+int xilinx_wr_config_fn(int assert_write, int flush, int cookie)
 {
 	gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
 
@@ -322,7 +322,7 @@ int xilinx_wr_fn(int assert_write, int flush, int cookie)
 	return assert_write;
 }
 
-int xilinx_fastwr_fn(void *buf, size_t len, int flush, int cookie)
+int xilinx_fastwr_config_fn(void *buf, size_t len, int flush, int cookie)
 {
 	size_t bytecount = 0;
 	gpio_t *gpiop = (gpio_t *)MMAP_GPIO;
@@ -363,23 +363,24 @@ int xilinx_fastwr_fn(void *buf, size_t len, int flush, int cookie)
  * relocated at runtime.
  * FIXME: relocation not yet working for coldfire, see below!
  */
-Xilinx_Spartan3_Slave_Serial_fns xilinx_fns = {
+xilinx_spartan3_slave_serial_fns xilinx_fns = {
 	xilinx_pre_config_fn,
-	xilinx_pgm_fn,
-	xilinx_clk_fn,
-	xilinx_init_fn,
-	xilinx_done_fn,
-	xilinx_wr_fn,
+	xilinx_pgm_config_fn,
+	xilinx_clk_config_fn,
+	xilinx_init_config_fn,
+	xilinx_done_config_fn,
+	xilinx_wr_config_fn,
 	0,
-	xilinx_fastwr_fn
+	xilinx_fastwr_config_fn
 };
 
-Xilinx_desc xilinx_fpga[CONFIG_FPGA_COUNT] = {
-	{Xilinx_Spartan3,
+xilinx_desc xilinx_fpga[CONFIG_FPGA_COUNT] = {
+	{xilinx_spartan3,
 	 slave_serial,
 	 XILINX_XC3S4000_SIZE,
 	 (void *)&xilinx_fns,
-	 0}
+	 0,
+	 &spartan3_op}
 };
 
 /* Initialize the fpga.  Return 1 on success, 0 on failure. */
@@ -395,12 +396,12 @@ int astro5373l_xilinx_load(void)
 		 * so set stuff here instead of static initialisation:
 		 */
 		xilinx_fns.pre = xilinx_pre_config_fn;
-		xilinx_fns.pgm = xilinx_pgm_fn;
-		xilinx_fns.clk = xilinx_clk_fn;
-		xilinx_fns.init = xilinx_init_fn;
-		xilinx_fns.done = xilinx_done_fn;
-		xilinx_fns.wr = xilinx_wr_fn;
-		xilinx_fns.bwr = xilinx_fastwr_fn;
+		xilinx_fns.pgm = xilinx_pgm_config_fn;
+		xilinx_fns.clk = xilinx_clk_config_fn;
+		xilinx_fns.init = xilinx_init_config_fn;
+		xilinx_fns.done = xilinx_done_config_fn;
+		xilinx_fns.wr = xilinx_wr_config_fn;
+		xilinx_fns.bwr = xilinx_fastwr_config_fn;
 		xilinx_fpga[i].iface_fns = (void *)&xilinx_fns;
 		fpga_add(fpga_xilinx, &xilinx_fpga[i]);
 	}
diff --git a/board/balloon3/balloon3.c b/board/balloon3/balloon3.c
index 04e0574..aa108ca 100644
--- a/board/balloon3/balloon3.c
+++ b/board/balloon3/balloon3.c
@@ -191,7 +191,7 @@ int fpga_cs_fn(int assert_clk, int flush, int cookie)
 	return assert_clk;
 }
 
-Xilinx_Spartan3_Slave_Parallel_fns balloon3_fpga_fns = {
+xilinx_spartan3_slave_parallel_fns balloon3_fpga_fns = {
 	fpga_pre_config_fn,
 	fpga_pgm_fn,
 	fpga_init_fn,
@@ -207,7 +207,7 @@ Xilinx_Spartan3_Slave_Parallel_fns balloon3_fpga_fns = {
 	fpga_post_config_fn,
 };
 
-Xilinx_desc fpga = XILINX_XC3S1000_DESC(slave_parallel,
+xilinx_desc fpga = XILINX_XC3S1000_DESC(slave_parallel,
 			(void *)&balloon3_fpga_fns, 0);
 
 /* Initialize the FPGA */
diff --git a/board/bct-brettl2/bct-brettl2.c b/board/bct-brettl2/bct-brettl2.c
index de5b9ff..6be9b18 100644
--- a/board/bct-brettl2/bct-brettl2.c
+++ b/board/bct-brettl2/bct-brettl2.c
@@ -12,7 +12,6 @@
 #include <asm/blackfin.h>
 #include <asm/portmux.h>
 #include <asm/gpio.h>
-#include <asm/net.h>
 #include <net.h>
 #include <netdev.h>
 #include <miiphy.h>
@@ -33,7 +32,7 @@ int checkboard(void)
 static void board_init_enetaddr(uchar *mac_addr)
 {
 	puts("Warning: Generating 'random' MAC address\n");
-	bfin_gen_rand_mac(mac_addr);
+	eth_random_addr(mac_addr);
 	eth_setenv_enetaddr("ethaddr", mac_addr);
 }
 
diff --git a/board/bf518f-ezbrd/bf518f-ezbrd.c b/board/bf518f-ezbrd/bf518f-ezbrd.c
index 09a2353..3a94a57 100644
--- a/board/bf518f-ezbrd/bf518f-ezbrd.c
+++ b/board/bf518f-ezbrd/bf518f-ezbrd.c
@@ -13,7 +13,6 @@
 #include <netdev.h>
 #include <spi.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 #include <asm/portmux.h>
 #include <asm/mach-common/bits/otp.h>
 #include <asm/sdh.h>
@@ -48,7 +47,7 @@ static void board_init_enetaddr(uchar *mac_addr)
 
 	if (!valid_mac) {
 		puts("Warning: Generating 'random' MAC address\n");
-		bfin_gen_rand_mac(mac_addr);
+		eth_random_addr(mac_addr);
 	}
 
 	eth_setenv_enetaddr("ethaddr", mac_addr);
diff --git a/board/bf526-ezbrd/bf526-ezbrd.c b/board/bf526-ezbrd/bf526-ezbrd.c
index 4695b11..368d6be 100644
--- a/board/bf526-ezbrd/bf526-ezbrd.c
+++ b/board/bf526-ezbrd/bf526-ezbrd.c
@@ -12,7 +12,6 @@
 #include <net.h>
 #include <netdev.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 #include <asm/mach-common/bits/otp.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -45,7 +44,7 @@ static void board_init_enetaddr(uchar *mac_addr)
 
 	if (!valid_mac) {
 		puts("Warning: Generating 'random' MAC address\n");
-		bfin_gen_rand_mac(mac_addr);
+		eth_random_addr(mac_addr);
 	}
 
 	eth_setenv_enetaddr("ethaddr", mac_addr);
diff --git a/board/bf527-ezkit/bf527-ezkit.c b/board/bf527-ezkit/bf527-ezkit.c
index 211cf24..88e1869 100644
--- a/board/bf527-ezkit/bf527-ezkit.c
+++ b/board/bf527-ezkit/bf527-ezkit.c
@@ -13,7 +13,6 @@
 #include <netdev.h>
 #include <asm/blackfin.h>
 #include <asm/gpio.h>
-#include <asm/net.h>
 #include <asm/mach-common/bits/otp.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -47,7 +46,7 @@ static void board_init_enetaddr(uchar *mac_addr)
 
 	if (!valid_mac) {
 		puts("Warning: Generating 'random' MAC address\n");
-		bfin_gen_rand_mac(mac_addr);
+		eth_random_addr(mac_addr);
 	}
 
 	eth_setenv_enetaddr("ethaddr", mac_addr);
diff --git a/board/bf537-minotaur/bf537-minotaur.c b/board/bf537-minotaur/bf537-minotaur.c
index 920429c..ca61ef9 100644
--- a/board/bf537-minotaur/bf537-minotaur.c
+++ b/board/bf537-minotaur/bf537-minotaur.c
@@ -12,7 +12,6 @@
 #include <netdev.h>
 #include <net.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -27,7 +26,7 @@ int checkboard(void)
 static void board_init_enetaddr(uchar *mac_addr)
 {
 	puts("Warning: Generating 'random' MAC address\n");
-	bfin_gen_rand_mac(mac_addr);
+	eth_random_addr(mac_addr);
 	eth_setenv_enetaddr("ethaddr", mac_addr);
 }
 
diff --git a/board/bf537-pnav/bf537-pnav.c b/board/bf537-pnav/bf537-pnav.c
index c512528..df00110 100644
--- a/board/bf537-pnav/bf537-pnav.c
+++ b/board/bf537-pnav/bf537-pnav.c
@@ -12,7 +12,6 @@
 #include <netdev.h>
 #include <net.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -27,7 +26,7 @@ int checkboard(void)
 static void board_init_enetaddr(uchar *mac_addr)
 {
 	puts("Warning: Generating 'random' MAC address\n");
-	bfin_gen_rand_mac(mac_addr);
+	eth_random_addr(mac_addr);
 	eth_setenv_enetaddr("ethaddr", mac_addr);
 }
 
diff --git a/board/bf537-srv1/bf537-srv1.c b/board/bf537-srv1/bf537-srv1.c
index 04d3891..725296a 100644
--- a/board/bf537-srv1/bf537-srv1.c
+++ b/board/bf537-srv1/bf537-srv1.c
@@ -12,7 +12,6 @@
 #include <netdev.h>
 #include <net.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -27,7 +26,7 @@ int checkboard(void)
 static void board_init_enetaddr(uchar *mac_addr)
 {
 	puts("Warning: Generating 'random' MAC address\n");
-	bfin_gen_rand_mac(mac_addr);
+	eth_random_addr(mac_addr);
 	eth_setenv_enetaddr("ethaddr", mac_addr);
 }
 
diff --git a/board/bf537-stamp/bf537-stamp.c b/board/bf537-stamp/bf537-stamp.c
index 5fdf837..32045a9 100644
--- a/board/bf537-stamp/bf537-stamp.c
+++ b/board/bf537-stamp/bf537-stamp.c
@@ -13,7 +13,6 @@
 #include <config.h>
 #include <command.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 #include <net.h>
 #include <asm/mach-common/bits/bootrom.h>
 #include <netdev.h>
@@ -48,7 +47,7 @@ static void board_init_enetaddr(uchar *mac_addr)
 
 	if (!valid_mac) {
 		puts("Warning: Generating 'random' MAC address\n");
-		bfin_gen_rand_mac(mac_addr);
+		eth_random_addr(mac_addr);
 	}
 
 	eth_setenv_enetaddr("ethaddr", mac_addr);
diff --git a/board/buffalo/lsxl/lsxl.c b/board/buffalo/lsxl/lsxl.c
index eca1683..659a124 100644
--- a/board/buffalo/lsxl/lsxl.c
+++ b/board/buffalo/lsxl/lsxl.c
@@ -231,7 +231,7 @@ static void rescue_mode(void)
 	printf("Entering rescue mode..\n");
 #ifdef CONFIG_RANDOM_MACADDR
 	if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
-		eth_random_enetaddr(enetaddr);
+		eth_random_addr(enetaddr);
 		if (eth_setenv_enetaddr("ethaddr", enetaddr)) {
 			printf("Failed to set ethernet address\n");
 				set_led(LED_ALARM_BLINKING);
diff --git a/board/cm-bf527/cm-bf527.c b/board/cm-bf527/cm-bf527.c
index a5f70a4..1533eb9 100644
--- a/board/cm-bf527/cm-bf527.c
+++ b/board/cm-bf527/cm-bf527.c
@@ -11,7 +11,6 @@
 #include <net.h>
 #include <netdev.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 #include <asm/mach-common/bits/otp.h>
 #include "../cm-bf537e/gpio_cfi_flash.h"
 
@@ -46,7 +45,7 @@ static void board_init_enetaddr(uchar *mac_addr)
 
 	if (!valid_mac) {
 		puts("Warning: Generating 'random' MAC address\n");
-		bfin_gen_rand_mac(mac_addr);
+		eth_random_addr(mac_addr);
 	}
 
 	eth_setenv_enetaddr("ethaddr", mac_addr);
diff --git a/board/cm-bf537e/cm-bf537e.c b/board/cm-bf537e/cm-bf537e.c
index 8daf3ad..e79f90f 100644
--- a/board/cm-bf537e/cm-bf537e.c
+++ b/board/cm-bf537e/cm-bf537e.c
@@ -12,7 +12,6 @@
 #include <net.h>
 #include <netdev.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 #include "gpio_cfi_flash.h"
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -32,7 +31,7 @@ static void board_init_enetaddr(char *var)
 		return;
 
 	printf("Warning: %s: generating 'random' MAC address\n", var);
-	bfin_gen_rand_mac(enetaddr);
+	eth_random_addr(enetaddr);
 	eth_setenv_enetaddr(var, enetaddr);
 }
 
diff --git a/board/cm-bf537u/cm-bf537u.c b/board/cm-bf537u/cm-bf537u.c
index 5941b5f..632cbda 100644
--- a/board/cm-bf537u/cm-bf537u.c
+++ b/board/cm-bf537u/cm-bf537u.c
@@ -12,7 +12,6 @@
 #include <net.h>
 #include <netdev.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 #include "../cm-bf537e/gpio_cfi_flash.h"
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -32,7 +31,7 @@ static void board_init_enetaddr(char *var)
 		return;
 
 	printf("Warning: %s: generating 'random' MAC address\n", var);
-	bfin_gen_rand_mac(enetaddr);
+	eth_random_addr(enetaddr);
 	eth_setenv_enetaddr(var, enetaddr);
 }
 
diff --git a/board/dave/PPChameleonEVB/u-boot.lds b/board/dave/PPChameleonEVB/u-boot.lds
index 5af55e9..94b7076 100644
--- a/board/dave/PPChameleonEVB/u-boot.lds
+++ b/board/dave/PPChameleonEVB/u-boot.lds
@@ -4,7 +4,7 @@
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
-#include "config.h"	/* CONFIG_BOARDDIR */
+#include "config.h"
 
 #ifndef RESET_VECTOR_ADDRESS
 #define RESET_VECTOR_ADDRESS	0xfffffffc
diff --git a/board/dnp5370/dnp5370.c b/board/dnp5370/dnp5370.c
index 4b3873b..df721c9 100644
--- a/board/dnp5370/dnp5370.c
+++ b/board/dnp5370/dnp5370.c
@@ -14,7 +14,6 @@
 #include <common.h>
 #include <config.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 #include <net.h>
 #include <netdev.h>
 #include <asm/gpio.h>
@@ -55,7 +54,7 @@ static void board_init_enetaddr(uchar *mac_addr)
 
 	if (!valid_mac) {
 		puts("Warning: Generating 'random' MAC address\n");
-		bfin_gen_rand_mac(mac_addr);
+		eth_random_addr(mac_addr);
 	}
 
 	eth_setenv_enetaddr("ethaddr", mac_addr);
diff --git a/board/esd/pmc440/fpga.c b/board/esd/pmc440/fpga.c
index b7b62dd..f876da8 100644
--- a/board/esd/pmc440/fpga.c
+++ b/board/esd/pmc440/fpga.c
@@ -20,7 +20,7 @@ DECLARE_GLOBAL_DATA_PTR;
 #define USE_SP_CODE
 
 #ifdef USE_SP_CODE
-Xilinx_Spartan3_Slave_Parallel_fns pmc440_fpga_fns = {
+xilinx_spartan3_slave_parallel_fns pmc440_fpga_fns = {
 	fpga_pre_config_fn,
 	fpga_pgm_fn,
 	fpga_init_fn,
@@ -36,7 +36,7 @@ Xilinx_Spartan3_Slave_Parallel_fns pmc440_fpga_fns = {
 	fpga_post_config_fn,
 };
 #else
-Xilinx_Spartan3_Slave_Serial_fns pmc440_fpga_fns = {
+xilinx_spartan3_slave_serial_fns pmc440_fpga_fns = {
 	fpga_pre_config_fn,
 	fpga_pgm_fn,
 	fpga_clk_fn,
@@ -47,7 +47,7 @@ Xilinx_Spartan3_Slave_Serial_fns pmc440_fpga_fns = {
 };
 #endif
 
-Xilinx_Spartan2_Slave_Serial_fns ngcc_fpga_fns = {
+xilinx_spartan2_slave_serial_fns ngcc_fpga_fns = {
 	ngcc_fpga_pre_config_fn,
 	ngcc_fpga_pgm_fn,
 	ngcc_fpga_clk_fn,
@@ -57,7 +57,7 @@ Xilinx_Spartan2_Slave_Serial_fns ngcc_fpga_fns = {
 	ngcc_fpga_post_config_fn
 };
 
-Xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
+xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
 	XILINX_XC3S1200E_DESC(
 #ifdef USE_SP_CODE
 		slave_parallel,
diff --git a/board/esd/pmc440/u-boot-nand.lds b/board/esd/pmc440/u-boot-nand.lds
deleted file mode 100644
index bd801cc..0000000
--- a/board/esd/pmc440/u-boot-nand.lds
+++ /dev/null
@@ -1,118 +0,0 @@
-/*
- * (C) Copyright 2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .interp : { *(.interp) }
-  .hash          : { *(.hash)		}
-  .dynsym        : { *(.dynsym)		}
-  .dynstr        : { *(.dynstr)		}
-  .rel.text      : { *(.rel.text)		}
-  .rela.text     : { *(.rela.text)	}
-  .rel.data      : { *(.rel.data)		}
-  .rela.data     : { *(.rela.data)	}
-  .rel.rodata    : { *(.rel.rodata)	}
-  .rela.rodata   : { *(.rela.rodata)	}
-  .rel.got       : { *(.rel.got)		}
-  .rela.got      : { *(.rela.got)		}
-  .rel.ctors     : { *(.rel.ctors)	}
-  .rela.ctors    : { *(.rela.ctors)	}
-  .rel.dtors     : { *(.rel.dtors)	}
-  .rela.dtors    : { *(.rela.dtors)	}
-  .rel.bss       : { *(.rel.bss)		}
-  .rela.bss      : { *(.rela.bss)		}
-  .rel.plt       : { *(.rel.plt)		}
-  .rela.plt      : { *(.rela.plt)		}
-  .init          : { *(.init)	}
-  .plt : { *(.plt) }
-  .text      :
-  {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
-    arch/powerpc/cpu/ppc4xx/start.o	(.text)
-
-    /* Align to next NAND block */
-    . = ALIGN(0x4000);
-    common/env_embedded.o  (.ppcenv)
-    /* Keep some space here for redundant env and potential bad env blocks */
-    . = ALIGN(0x10000);
-
-    *(.text)
-    *(.got1)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-  .fini      : { *(.fini)    } =0
-  .ctors     : { *(.ctors)   }
-  .dtors     : { *(.dtors)   }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    *(.got)
-    _GOT2_TABLE_ = .;
-    *(.got2)
-    _FIXUP_TABLE_ = .;
-    *(.fixup)
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data)
-    *(.data1)
-    *(.sdata)
-    *(.sdata2)
-    *(.dynamic)
-    CONSTRUCTORS
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  .u_boot_list : {
-		KEEP(*(SORT(.u_boot_list*)));
-  }
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.sbss) *(.scommon)
-   *(.dynbss)
-   *(.bss)
-   *(COMMON)
-   . = ALIGN(4);
-  }
-
-  __bss_end = . ;
-  PROVIDE (end = .);
-}
diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c
index d9c88a0..b2d5378 100644
--- a/board/freescale/b4860qds/b4860qds.c
+++ b/board/freescale/b4860qds/b4860qds.c
@@ -23,6 +23,7 @@
 #include "../common/qixis.h"
 #include "../common/vsc3316_3308.h"
 #include "../common/idt8t49n222a_serdes_clk.h"
+#include "../common/zm7300.h"
 #include "b4860qds.h"
 #include "b4860qds_qixis.h"
 #include "b4860qds_crossbar_con.h"
@@ -94,6 +95,238 @@ int select_i2c_ch_pca(u8 ch)
 	return 0;
 }
 
+/*
+ * read_voltage from sensor on I2C bus
+ * We use average of 4 readings, waiting for 532us befor another reading
+ */
+#define WAIT_FOR_ADC	532	/* wait for 532 microseconds for ADC */
+#define NUM_READINGS	4	/* prefer to be power of 2 for efficiency */
+
+static inline int read_voltage(void)
+{
+	int i, ret, voltage_read = 0;
+	u16 vol_mon;
+
+	for (i = 0; i < NUM_READINGS; i++) {
+		ret = i2c_read(I2C_VOL_MONITOR_ADDR,
+			I2C_VOL_MONITOR_BUS_V_OFFSET, 1, (void *)&vol_mon, 2);
+		if (ret) {
+			printf("VID: failed to read core voltage\n");
+			return ret;
+		}
+		if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) {
+			printf("VID: Core voltage sensor error\n");
+			return -1;
+		}
+		debug("VID: bus voltage reads 0x%04x\n", vol_mon);
+		/* LSB = 4mv */
+		voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4;
+		udelay(WAIT_FOR_ADC);
+	}
+	/* calculate the average */
+	voltage_read /= NUM_READINGS;
+
+	return voltage_read;
+}
+
+static int adjust_vdd(ulong vdd_override)
+{
+	int re_enable = disable_interrupts();
+	ccsr_gur_t __iomem *gur =
+		(void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 fusesr;
+	u8 vid;
+	int vdd_target, vdd_last;
+	int existing_voltage, temp_voltage, voltage; /* all in 1/10 mV */
+	int ret;
+	unsigned int orig_i2c_speed;
+	unsigned long vdd_string_override;
+	char *vdd_string;
+	static const uint16_t vdd[32] = {
+		0,	/* unused */
+		9875,	/* 0.9875V */
+		9750,
+		9625,
+		9500,
+		9375,
+		9250,
+		9125,
+		9000,
+		8875,
+		8750,
+		8625,
+		8500,
+		8375,
+		8250,
+		8125,
+		10000,	/* 1.0000V */
+		10125,
+		10250,
+		10375,
+		10500,
+		10625,
+		10750,
+		10875,
+		11000,
+		0,	/* reserved */
+	};
+	struct vdd_drive {
+		u8 vid;
+		unsigned voltage;
+	};
+
+	ret = select_i2c_ch_pca(I2C_MUX_CH_VOL_MONITOR);
+	if (ret) {
+		printf("VID: I2c failed to switch channel\n");
+		ret = -1;
+		goto exit;
+	}
+
+	/* get the voltage ID from fuse status register */
+	fusesr = in_be32(&gur->dcfg_fusesr);
+	vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) &
+		FSL_CORENET_DCFG_FUSESR_VID_MASK;
+	if (vid == FSL_CORENET_DCFG_FUSESR_VID_MASK) {
+		vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) &
+			FSL_CORENET_DCFG_FUSESR_ALTVID_MASK;
+	}
+	vdd_target = vdd[vid];
+	debug("VID:Reading from from fuse,vid=%x vdd is %dmV\n",
+	      vid, vdd_target/10);
+
+	/* check override variable for overriding VDD */
+	vdd_string = getenv("b4qds_vdd_mv");
+	if (vdd_override == 0 && vdd_string &&
+	    !strict_strtoul(vdd_string, 10, &vdd_string_override))
+		vdd_override = vdd_string_override;
+	if (vdd_override >= 819 && vdd_override <= 1212) {
+		vdd_target = vdd_override * 10; /* convert to 1/10 mV */
+		debug("VDD override is %lu\n", vdd_override);
+	} else if (vdd_override != 0) {
+		printf("Invalid value.\n");
+	}
+
+	if (vdd_target == 0) {
+		printf("VID: VID not used\n");
+		ret = 0;
+		goto exit;
+	}
+
+	/*
+	 * Read voltage monitor to check real voltage.
+	 * Voltage monitor LSB is 4mv.
+	 */
+	vdd_last = read_voltage();
+	if (vdd_last < 0) {
+		printf("VID: abort VID adjustment\n");
+		ret = -1;
+		goto exit;
+	}
+
+	debug("VID: Core voltage is at %d mV\n", vdd_last);
+	ret = select_i2c_ch_pca(I2C_MUX_CH_DPM);
+	if (ret) {
+		printf("VID: I2c failed to switch channel to DPM\n");
+		ret = -1;
+		goto exit;
+	}
+
+	/* Round up to the value of step of Voltage regulator */
+	voltage = roundup(vdd_target, ZM_STEP);
+	debug("VID: rounded up voltage = %d\n", voltage);
+
+	/* lower the speed to 100kHz to access ZM7300 device */
+	debug("VID: Setting bus speed to 100KHz if not already set\n");
+	orig_i2c_speed = i2c_get_bus_speed();
+	if (orig_i2c_speed != 100000)
+		i2c_set_bus_speed(100000);
+
+	/* Read the existing level on board, if equal to requsted one,
+	   no need to re-set */
+	existing_voltage = zm_read_voltage();
+
+	/* allowing the voltage difference of one step 0.0125V acceptable */
+	if ((existing_voltage >= voltage) &&
+	    (existing_voltage < (voltage + ZM_STEP))) {
+		debug("VID: voltage already set as requested,returning\n");
+		ret = existing_voltage;
+		goto out;
+	}
+	debug("VID: Changing voltage for board from %dmV to %dmV\n",
+	      existing_voltage/10, voltage/10);
+
+	if (zm_disable_wp() < 0) {
+		ret = -1;
+		goto out;
+	}
+	/* Change Voltage: the change is done through all the steps in the
+	   way, to avoid reset to the board due to power good signal fail
+	   in big voltage change gap jump.
+	*/
+	if (existing_voltage > voltage) {
+		temp_voltage = existing_voltage - ZM_STEP;
+			while (temp_voltage >= voltage) {
+				ret = zm_write_voltage(temp_voltage);
+				if (ret == temp_voltage) {
+					temp_voltage -= ZM_STEP;
+				} else {
+					/* ZM7300 device failed to set
+					 * the voltage */
+					printf
+					("VID:Stepping down vol failed:%dmV\n",
+					 temp_voltage/10);
+				     ret = -1;
+				     goto out;
+				}
+			}
+	} else {
+		temp_voltage = existing_voltage + ZM_STEP;
+			while (temp_voltage < (voltage + ZM_STEP)) {
+				ret = zm_write_voltage(temp_voltage);
+				if (ret == temp_voltage) {
+					temp_voltage += ZM_STEP;
+				} else {
+					/* ZM7300 device failed to set
+					 * the voltage */
+					printf
+					("VID:Stepping up vol failed:%dmV\n",
+					 temp_voltage/10);
+				     ret = -1;
+				     goto out;
+				}
+			}
+	}
+
+	if (zm_enable_wp() < 0)
+		ret = -1;
+
+	/* restore the speed to 400kHz */
+out:	debug("VID: Restore the I2C bus speed to %dKHz\n",
+				orig_i2c_speed/1000);
+	i2c_set_bus_speed(orig_i2c_speed);
+	if (ret < 0)
+		goto exit;
+
+	ret = select_i2c_ch_pca(I2C_MUX_CH_VOL_MONITOR);
+	if (ret) {
+		printf("VID: I2c failed to switch channel\n");
+		ret = -1;
+		goto exit;
+	}
+	vdd_last = read_voltage();
+	select_i2c_ch_pca(I2C_CH_DEFAULT);
+
+	if (vdd_last > 0)
+		printf("VID: Core voltage %d mV\n", vdd_last);
+	else
+		ret = -1;
+
+exit:
+	if (re_enable)
+		enable_interrupts();
+	return ret;
+}
+
 int configure_vsc3316_3308(void)
 {
 	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
@@ -697,6 +930,13 @@ int board_early_init_r(void)
 #ifdef CONFIG_SYS_DPAA_QBMAN
 	setup_portals();
 #endif
+	/*
+	 * Adjust core voltage according to voltage ID
+	 * This function changes I2C mux to channel 2.
+	 */
+	if (adjust_vdd(0) < 0)
+		printf("Warning: Adjusting core voltage failed\n");
+
 	/* SerDes1 refclks need to be set again, as default clks
 	 * are not suitable for CPRI and onboard SGMIIs to work
 	 * simultaneously.
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index f6a0879..22b57cc 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -48,6 +48,7 @@ obj-$(CONFIG_P5020DS)		+= ics307_clk.o
 obj-$(CONFIG_P5040DS)		+= ics307_clk.o
 obj-$(CONFIG_VSC_CROSSBAR)    += vsc3316_3308.o
 obj-$(CONFIG_IDT8T49N222A)	+= idt8t49n222a_serdes_clk.o
+obj-$(CONFIG_ZM7300)		+= zm7300.o
 
 # deal with common files for P-series corenet based devices
 obj-$(CONFIG_P2041RDB)	+= p_corenet/
diff --git a/board/freescale/common/sys_eeprom.c b/board/freescale/common/sys_eeprom.c
index 9c18dd8..6144c53 100644
--- a/board/freescale/common/sys_eeprom.c
+++ b/board/freescale/common/sys_eeprom.c
@@ -21,7 +21,7 @@
 /* some boards with non-256-bytes EEPROM have special define */
 /* for MAX_NUM_PORTS in board-specific file */
 #ifndef MAX_NUM_PORTS
-#define MAX_NUM_PORTS	23
+#define MAX_NUM_PORTS	16
 #endif
 #define NXID_VERSION	1
 #endif
@@ -58,8 +58,9 @@ static struct __attribute__ ((__packed__)) eeprom {
 	u8 res_1[21];     /* 0x2b - 0x3f Reserved */
 	u8 mac_count;     /* 0x40        Number of MAC addresses */
 	u8 mac_flag;      /* 0x41        MAC table flags */
-	u8 mac[MAX_NUM_PORTS][6];     /* 0x42 - x MAC addresses */
-	u32 crc;          /* x+1         CRC32 checksum */
+	u8 mac[MAX_NUM_PORTS][6];     /* 0x42 - 0xa1 MAC addresses */
+	u8 res_2[90];     /* 0xa2 - 0xfb Reserved */	
+	u32 crc;          /* 0xfc - 0xff CRC32 checksum */
 #endif
 } e;
 
@@ -425,13 +426,13 @@ int mac_read_from_eeprom(void)
 
 	if (read_eeprom()) {
 		printf("Read failed.\n");
-		return -1;
+		return 0;
 	}
 
 	if (!is_valid) {
 		printf("Invalid ID (%02x %02x %02x %02x)\n",
 		       e.id[0], e.id[1], e.id[2], e.id[3]);
-		return -1;
+		return 0;
 	}
 
 #ifdef CONFIG_SYS_I2C_EEPROM_NXID
@@ -447,7 +448,7 @@ int mac_read_from_eeprom(void)
 	crcp = (void *)&e + crc_offset;
 	if (crc != be32_to_cpu(*crcp)) {
 		printf("CRC mismatch (%08x != %08x)\n", crc, be32_to_cpu(e.crc));
-		return -1;
+		return 0;
 	}
 
 #ifdef CONFIG_SYS_I2C_EEPROM_NXID
diff --git a/board/freescale/common/zm7300.c b/board/freescale/common/zm7300.c
new file mode 100644
index 0000000..be5953a
--- /dev/null
+++ b/board/freescale/common/zm7300.c
@@ -0,0 +1,235 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+/* Power-One ZM7300 DPM */
+#include "zm7300.h"
+
+#define DPM_WP 0x96
+#define WRP_OPCODE 0x01
+#define WRM_OPCODE 0x02
+#define RRP_OPCODE 0x11
+
+#define DPM_SUCCESS 0x01
+#define DPM_EXEC_FAIL 0x00
+
+static const uint16_t hex_to_1_10mv[] = {
+	5000,
+	5125,
+	5250,
+	5375,
+	5500,
+	5625,
+	5750,
+	5875,
+	6000,
+	6125,
+	6250,
+	6375,
+	6500,
+	6625,
+	6750,
+	6875,
+	7000,
+	7125,
+	7250,
+	7375,
+	7500,
+	7625,
+	7750,
+	7875,
+	8000,
+	8125,
+	8250,
+	8375,
+	8500,
+	8625,
+	8750,
+	8875,
+	9000,
+	9125,
+	9250,
+	9375,
+	9500,  /* 0.95mV */
+	9625,
+	9750,
+	9875,
+	10000,  /* 1.0V */
+	10125,
+	10250,
+	10375,
+	10500,
+	10625,
+	10750,
+	10875,
+	11000,
+	11125,
+	11250,
+	11375,
+	11500,
+	11625,
+	11750,
+	11875,
+	12000,
+	12125,
+	12250,
+	12375,
+	0,	/* reserved */
+};
+
+
+/* Read Data d from Register r of POL p */
+u8 dpm_rrp(uchar r)
+{
+	u8 ret[5];
+
+	ret[0] = RRP_OPCODE;
+	/* POL is 0 */
+	ret[1] = 0;
+	ret[2] = r;
+	i2c_read(I2C_DPM_ADDR, 0, -3, ret, 2);
+	if (ret[1] == DPM_SUCCESS) { /* the DPM returned success as status */
+		debug("RRP_OPCODE returned success data is %x\n", ret[0]);
+		return ret[0];
+	} else {
+		return -1;
+	}
+}
+
+/* Write Data d into DPM register r (RAM) */
+int dpm_wrm(u8 r, u8 d)
+{
+	u8 ret[5];
+
+	ret[0] = WRM_OPCODE;
+	ret[1] = r;
+	ret[2] = d;
+	i2c_read(I2C_DPM_ADDR, 0, -3, ret, 1);
+	if (ret[0] == DPM_SUCCESS) { /* the DPM returned success as status */
+		debug("WRM_OPCODE returned success data is %x\n", ret[0]);
+		return ret[0];
+	} else {
+		return -1;
+	}
+}
+
+/* Write Data d into Register r of POL(s) a */
+int dpm_wrp(u8 r, u8 d)
+{
+	u8 ret[7];
+
+	ret[0] = WRP_OPCODE;
+	/* only POL0 is present */
+	ret[1] = 0x01;
+	ret[2] = 0x00;
+	ret[3] = 0x00;
+	ret[4] = 0x00;
+	ret[5] = r;
+	ret[6] = d;
+	i2c_read(I2C_DPM_ADDR, 0, -7, ret, 1);
+	if (ret[0] == DPM_SUCCESS) { /* the DPM returned success as status */
+		debug("WRP_OPCODE returned success data is %x\n", ret[0]);
+		return 0;
+	} else {
+		return -1;
+	}
+}
+
+/* Uses the DPM command RRP */
+u8 zm_read(uchar reg)
+{
+	u8 d;
+	d = dpm_rrp(reg);
+	return d;
+}
+
+/* ZM_write --
+	Steps:
+	a. Write data to the register
+	b. Read data from register and compare to written value
+	c. Return return_code & voltage_read
+*/
+u8 zm_write(u8 reg, u8 data)
+{
+	u8 d;
+
+	/* write data to register */
+	dpm_wrp(reg, data);
+
+	/* read register and compare to written value */
+	d = dpm_rrp(reg);
+	if (d != data) {
+		printf("zm_write : Comparison register data failed\n");
+		return -1;
+	}
+
+	return d;
+}
+
+/* zm_write_out_voltage
+ * voltage in 1/10 mV
+ */
+int zm_write_voltage(int voltage)
+{
+	u8 reg = 0x7, vid;
+	uint16_t voltage_read;
+	u8 ret;
+
+	vid =  (voltage - 5000) / ZM_STEP;
+
+	ret = zm_write(reg, vid);
+	if (ret != -1) {
+		voltage_read = hex_to_1_10mv[ret];
+		debug("voltage set to %dmV\n", voltage_read/10);
+		return voltage_read;
+	}
+	return -1;
+}
+
+/* zm_read_out_voltage
+ * voltage in 1/10 mV
+ */
+int zm_read_voltage(void)
+{
+	u8 reg = 0x7;
+	u8 ret;
+	int voltage;
+
+	ret = zm_read(reg);
+	if (ret != -1) {
+		voltage =  hex_to_1_10mv[ret];
+		debug("Voltage read is %dmV\n", voltage/10);
+		return voltage;
+	} else {
+		return -1;
+	}
+}
+
+int zm_disable_wp()
+{
+	u8 new_wp_value;
+
+	/* Disable using Write-Protect register 0x96 */
+	new_wp_value = 0x8;
+	if ((dpm_wrm(DPM_WP, new_wp_value)) < 0) {
+		printf("Disable Write-Protect register failed\n");
+		return -1;
+	}
+	return 0;
+}
+
+int zm_enable_wp()
+{
+	u8 orig_wp_value;
+	orig_wp_value = 0x0;
+
+	/* Enable using Write-Protect register 0x96 */
+	if ((dpm_wrm(DPM_WP, orig_wp_value)) < 0) {
+		printf("Enable Write-Protect register failed\n");
+		return -1;
+	}
+	return 0;
+}
+
diff --git a/board/freescale/common/zm7300.h b/board/freescale/common/zm7300.h
new file mode 100644
index 0000000..6b4d035
--- /dev/null
+++ b/board/freescale/common/zm7300.h
@@ -0,0 +1,22 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#ifndef __ZM7300_H_
+#define __ZM7300_H	1_
+
+#include <common.h>
+#include <i2c.h>
+#include <errno.h>
+#include <asm/io.h>
+
+#define ZM_STEP 125
+int zm7300_set_voltage(int voltage_1_10mv);
+int zm_write_voltage(int voltage);
+int zm_read_voltage(void);
+int zm_disable_wp(void);
+int zm_enable_wp(void);
+
+#endif	/* __ZM7300_H_ */
diff --git a/board/freescale/p1_p2_rdb/Makefile b/board/freescale/p1_p2_rdb/Makefile
index f7b568a..a97bf45 100644
--- a/board/freescale/p1_p2_rdb/Makefile
+++ b/board/freescale/p1_p2_rdb/Makefile
@@ -4,8 +4,27 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+
+obj-y	+= spl_minimal.o tlb.o law.o
+
+else
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
 obj-y	+= p1_p2_rdb.o
+obj-$(CONFIG_PCI)  += pci.o
+endif
 obj-y	+= ddr.o
 obj-y	+= law.o
-obj-$(CONFIG_PCI)  += pci.o
 obj-y	+= tlb.o
+
+endif
diff --git a/board/freescale/p1_p2_rdb/ddr.c b/board/freescale/p1_p2_rdb/ddr.c
index 17d3bea..98ee5f1 100644
--- a/board/freescale/p1_p2_rdb/ddr.c
+++ b/board/freescale/p1_p2_rdb/ddr.c
@@ -180,27 +180,22 @@ fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = {
 
 phys_size_t fixed_sdram (void)
 {
-	char buf[32];
 	fsl_ddr_cfg_regs_t ddr_cfg_regs;
 	size_t ddr_size;
 	struct cpu_type *cpu;
 	ulong ddr_freq, ddr_freq_mhz;
 
 	cpu = gd->arch.cpu;
-	/* P1020 and it's derivatives support max 32bit DDR width */
-	if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) {
-		ddr_size = (CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 / 2);
-	} else {
-		ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-	}
+
+	ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+
 #if defined(CONFIG_SYS_RAMBOOT)
 	return ddr_size;
 #endif
 	ddr_freq = get_ddr_freq(0);
 	ddr_freq_mhz = ddr_freq / 1000000;
 
-	printf("Configuring DDR for %s MT/s data rate\n",
-				strmhz(buf, ddr_freq));
+	printf("Configuring DDR for %ld T/s data rate\n", ddr_freq);
 
 	if(ddr_freq_mhz <= 400)
 		memcpy(&ddr_cfg_regs, &ddr_cfg_regs_400, sizeof(ddr_cfg_regs));
@@ -211,8 +206,7 @@ phys_size_t fixed_sdram (void)
 	else if(ddr_freq_mhz <= 800)
 		memcpy(&ddr_cfg_regs, &ddr_cfg_regs_800, sizeof(ddr_cfg_regs));
 	else
-		panic("Unsupported DDR data rate %s MT/s data rate\n",
-					strmhz(buf, ddr_freq));
+		panic("Unsupported DDR data rate %ld T/s\n", ddr_freq);
 
 	/* P1020 and it's derivatives support max 32bit DDR width */
 	if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) {
diff --git a/board/freescale/p1_p2_rdb/spl.c b/board/freescale/p1_p2_rdb/spl.c
new file mode 100644
index 0000000..f30c5fe
--- /dev/null
+++ b/board/freescale/p1_p2_rdb/spl.c
@@ -0,0 +1,141 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <malloc.h>
+#include <mmc.h>
+#include <nand.h>
+#include <i2c.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define SYSCLK_MASK	0x00200000
+#define BOARDREV_MASK	0x10100000
+
+#define SYSCLK_66	66666666
+#define SYSCLK_100	100000000
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+	u32 val_gpdat, sysclk_gpio;
+
+	val_gpdat = in_be32(&pgpio->gpdat);
+	sysclk_gpio = val_gpdat & SYSCLK_MASK;
+
+	if (sysclk_gpio == 0)
+		return SYSCLK_66;
+	else
+		return SYSCLK_100;
+
+	return 0;
+}
+
+phys_size_t get_effective_memsize(void)
+{
+	return CONFIG_SYS_L2_SIZE;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, bus_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+	console_init_f();
+
+	/* Set pmuxcr to allow both i2c1 and i2c2 */
+	setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000);
+	setbits_be32(&gur->pmuxcr,
+		     in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA);
+
+	/* Read back the register to synchronize the write. */
+	in_be32(&gur->pmuxcr);
+
+#ifdef CONFIG_SPL_SPI_BOOT
+	clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
+#endif
+
+	/* initialize selected port with appropriate baud rate */
+	plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+	plat_ratio >>= 1;
+	bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+	gd->bus_clk = bus_clk;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     bus_clk / 16 / CONFIG_BAUDRATE);
+#ifdef CONFIG_SPL_MMC_BOOT
+	puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	puts("\nSPI Flash boot...\n");
+#endif
+
+	/* copy code to RAM and jump to it - this should not return */
+	/* NOTE - code has to be copied out of NAND buffer before
+	 * other blocks can be read.
+	 */
+	relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	/* Pointer is writable since we allocated a register for it */
+	gd = (gd_t *)CONFIG_SPL_GD_ADDR;
+	bd_t *bd;
+
+	memset(gd, 0, sizeof(gd_t));
+	bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L2_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_initialize(bd);
+#endif
+	/* relocate environment function pointers etc. */
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+	spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
+	gd->env_valid = 1;
+
+	gd->ram_size = initdram(0);
+#ifdef CONFIG_SPL_NAND_BOOT
+	puts("Tertiary program loader running in sram...");
+#else
+	puts("Second program loader running in sram...\n");
+#endif
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	nand_boot();
+#endif
+}
diff --git a/board/freescale/p1_p2_rdb/spl_minimal.c b/board/freescale/p1_p2_rdb/spl_minimal.c
new file mode 100644
index 0000000..96a4d1c
--- /dev/null
+++ b/board/freescale/p1_p2_rdb/spl_minimal.c
@@ -0,0 +1,84 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <linux/compiler.h>
+#include <asm/fsl_law.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/global_data.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+#define SYSCLK_MASK	0x00200000
+#define BOARDREV_MASK	0x10100000
+
+#define SYSCLK_66	66666666
+#define SYSCLK_100	100000000
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+	u32 val_gpdat, sysclk_gpio;
+
+	val_gpdat = in_be32(&pgpio->gpdat);
+	sysclk_gpio = val_gpdat & SYSCLK_MASK;
+
+	if (sysclk_gpio == 0)
+		return SYSCLK_66;
+	else
+		return SYSCLK_100;
+
+	return 0;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM)
+	set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM);
+	set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM);
+#endif
+
+	/* initialize selected port with appropriate baud rate */
+	plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+	plat_ratio >>= 1;
+	gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     gd->bus_clk / 16 / CONFIG_BAUDRATE);
+
+	puts("\nNAND boot... ");
+
+	/* copy code to RAM and jump to it - this should not return */
+	/* NOTE - code has to be copied out of NAND buffer before
+	 * other blocks can be read.
+	 */
+	relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	puts("\nSecond program loader running in sram...");
+	nand_boot();
+}
+
+void putc(char c)
+{
+	if (c == '\n')
+		NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+
+	NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+}
+
+void puts(const char *str)
+{
+	while (*str)
+		putc(*str++);
+}
diff --git a/board/freescale/p1_p2_rdb/tlb.c b/board/freescale/p1_p2_rdb/tlb.c
index bc98972..73f5729 100644
--- a/board/freescale/p1_p2_rdb/tlb.c
+++ b/board/freescale/p1_p2_rdb/tlb.c
@@ -37,6 +37,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 			0, 1, BOOKE_PAGESZ_1M, 1),
 
+#ifndef CONFIG_SPL_BUILD
 	/* W**G* - Flash/promjet, localbus */
 	/* This will be changed to *I*G* after relocation to RAM. */
 	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
@@ -55,6 +56,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			0, 4, BOOKE_PAGESZ_256K, 1),
 
 #endif /* #if defined(CONFIG_PCI) */
+#endif
 	/* *I*G - NAND */
 	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -65,7 +67,21 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 			0, 6, BOOKE_PAGESZ_1M, 1),
 
-#if defined(CONFIG_SYS_RAMBOOT)
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+	/* *I*G - L2SRAM */
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+		      0, 11, BOOKE_PAGESZ_256K, 1),
+#if CONFIG_SYS_L2_SIZE >= (256 << 10)
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
+		      CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 12, BOOKE_PAGESZ_256K, 1),
+#endif
+#endif
+
+#if defined(CONFIG_SYS_RAMBOOT) || \
+	(defined(CONFIG_SPL) && !defined(CONFIG_SPL_COMMON_INIT_DDR))
 	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
 			MAS3_SX|MAS3_SW|MAS3_SR, 0,
 			0, 7, BOOKE_PAGESZ_1G, 1)
diff --git a/board/freescale/qemu-ppce500/qemu-ppce500.c b/board/freescale/qemu-ppce500/qemu-ppce500.c
index 3dbb0cf..230870d 100644
--- a/board/freescale/qemu-ppce500/qemu-ppce500.c
+++ b/board/freescale/qemu-ppce500/qemu-ppce500.c
@@ -346,3 +346,23 @@ ulong get_bus_freq (ulong dummy)
 	get_sys_info(&sys_info);
 	return sys_info.freq_systembus;
 }
+
+/*
+ * Return the number of cores on this SOC.
+ */
+int cpu_numcores(void)
+{
+	/*
+	 * The QEMU u-boot target only needs to drive the first core,
+	 * spinning and device tree nodes get driven by QEMU itself
+	 */
+	return 1;
+}
+
+/*
+ * Return a 32-bit mask indicating which cores are present on this SOC.
+ */
+u32 cpu_mask(void)
+{
+	return (1 << cpu_numcores()) - 1;
+}
diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c
index fb5b849..a5e5fff 100644
--- a/board/freescale/t104xrdb/t104xrdb.c
+++ b/board/freescale/t104xrdb/t104xrdb.c
@@ -109,6 +109,8 @@ void ft_board_setup(void *blob, bd_t *bd)
 #ifdef CONFIG_DEEP_SLEEP
 void board_mem_sleep_setup(void)
 {
+	/* does not provide HW signals for power management */
+	CPLD_WRITE(misc_ctl_status, (CPLD_READ(misc_ctl_status) & ~0x40));
 	/* Disable MCKE isolation */
 	gpio_set_value(2, 0);
 	udelay(1);
diff --git a/board/freescale/t4rdb/Makefile b/board/freescale/t4rdb/Makefile
new file mode 100644
index 0000000..f7f7fc0
--- /dev/null
+++ b/board/freescale/t4rdb/Makefile
@@ -0,0 +1,12 @@
+#
+# Copyright 2014 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_T4240RDB) += t4240rdb.o
+obj-y	+= ddr.o
+obj-y	+= eth.o
+obj-$(CONFIG_PCI)	+= pci.o
+obj-y	+= law.o
+obj-y	+= tlb.o
diff --git a/board/freescale/t4rdb/ddr.c b/board/freescale/t4rdb/ddr.c
new file mode 100644
index 0000000..5a43c1b
--- /dev/null
+++ b/board/freescale/t4rdb/ddr.c
@@ -0,0 +1,118 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num > 2) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	/*
+	 * we use identical timing for all slots. If needed, change the code
+	 * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
+	 */
+	if (popts->registered_dimm_en)
+		pbsp = rdimms[0];
+	else
+		pbsp = udimms[0];
+
+
+	/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks &&
+		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found for data\n"
+			"rate %lu MT/s\n"
+			"Trying to use the highest speed (%u) parameters\n",
+			ddr_freq, pbsp_highest->datarate_mhz_high);
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+found:
+	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+		"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x,\n"
+		"wrlvl_ctrl_3 0x%x\n",
+		pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+		pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+		pbsp->wrlvl_ctl_3);
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	/* DHC_EN =1, ODT = 75 Ohm */
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+	puts("Initializing....using SPD\n");
+
+	dram_size = fsl_ddr_sdram();
+
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
+
+	puts("    DDR: ");
+	return dram_size;
+}
diff --git a/board/freescale/t4rdb/ddr.h b/board/freescale/t4rdb/ddr.h
new file mode 100644
index 0000000..7b85476
--- /dev/null
+++ b/board/freescale/t4rdb/ddr.h
@@ -0,0 +1,78 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+struct board_specific_parameters {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 rank_gb;
+	u32 clk_adjust;
+	u32 wrlvl_start;
+	u32 wrlvl_ctl_2;
+	u32 wrlvl_ctl_3;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_parameters udimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3
+	 */
+	{2,  1350, 4, 4,     8, 0x0809090b, 0x0c0c0d0a},
+	{2,  1350, 0, 5,     7, 0x0709090b, 0x0c0c0d09},
+	{2,  1666, 4, 4,     8, 0x080a0a0d, 0x0d10100b},
+	{2,  1666, 0, 5,     7, 0x080a0a0c, 0x0d0d0e0a},
+	{2,  1900, 0, 4,     8, 0x090a0b0e, 0x0f11120c},
+	{2,  2140, 0, 4,     8, 0x090a0b0e, 0x0f11120c},
+	{1,  1350, 0, 5,     8, 0x0809090b, 0x0c0c0d0a},
+	{1,  1700, 0, 5,     8, 0x080a0a0c, 0x0c0d0e0a},
+	{1,  1900, 0, 4,     8, 0x080a0a0c, 0x0e0e0f0a},
+	{1,  2140, 0, 4,     8, 0x090a0b0c, 0x0e0f100b},
+	{}
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3
+	 */
+	{4,  1350, 0, 5,     9, 0x08070605, 0x06070806},
+	{4,  1666, 0, 5,    11, 0x0a080706, 0x07090906},
+	{4,  2140, 0, 5,    12, 0x0b090807, 0x080a0b07},
+	{2,  1350, 0, 5,     9, 0x08070605, 0x06070806},
+	{2,  1666, 0, 5,    11, 0x0a090806, 0x08090a06},
+	{2,  2140, 0, 5,    12, 0x0b090807, 0x080a0b07},
+	{1,  1350, 0, 5,     9, 0x08070605, 0x06070806},
+	{1,  1666, 0, 5,    11, 0x0a090806, 0x08090a06},
+	{1,  2140, 0, 4,    12, 0x0b090807, 0x080a0b07},
+	{}
+};
+
+/*
+ * The three slots have slightly different timing. The center values are good
+ * for all slots. We use identical speed tables for them. In future use, if
+ * DIMMs require separated tables, make more entries as needed.
+ */
+static const struct board_specific_parameters *udimms[] = {
+	udimm0,
+};
+
+/*
+ * The three slots have slightly different timing. See comments above.
+ */
+static const struct board_specific_parameters *rdimms[] = {
+	rdimm0,
+};
+
+
+#endif
diff --git a/board/freescale/t4rdb/eth.c b/board/freescale/t4rdb/eth.c
new file mode 100644
index 0000000..d220475
--- /dev/null
+++ b/board/freescale/t4rdb/eth.c
@@ -0,0 +1,146 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * Chunhe Lan <Chunhe.Lan@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+#include <asm/fsl_serdes.h>
+#include <hwconfig.h>
+
+#include "../common/fman.h"
+#include "t4rdb.h"
+
+void fdt_fixup_board_enet(void *fdt)
+{
+	return;
+}
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FMAN_ENET)
+	int i, interface;
+	struct memac_mdio_info dtsec_mdio_info;
+	struct memac_mdio_info tgec_mdio_info;
+	struct mii_dev *dev;
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 srds_prtcl_s1, srds_prtcl_s2;
+
+	srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
+				FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+	srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+	srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
+				FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+	srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+
+	dtsec_mdio_info.regs =
+		(struct memac_mdio_controller *)CONFIG_SYS_FM2_DTSEC_MDIO_ADDR;
+
+	dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+	/* Register the 1G MDIO bus */
+	fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+	tgec_mdio_info.regs =
+		(struct memac_mdio_controller *)CONFIG_SYS_FM2_TGEC_MDIO_ADDR;
+	tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+	/* Register the 10G MDIO bus */
+	fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+	if (srds_prtcl_s1 == 28) {
+		/* SGMII */
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_PHY_ADDR1);
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_PHY_ADDR2);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_PHY_ADDR3);
+		fm_info_set_phy_address(FM1_DTSEC4, SGMII_PHY_ADDR4);
+	} else {
+		puts("Invalid SerDes1 protocol for T4240RDB\n");
+	}
+
+	for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+		interface = fm_info_get_enet_if(i);
+		switch (interface) {
+		case PHY_INTERFACE_MODE_SGMII:
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+			fm_info_set_mdio(i, dev);
+			break;
+		default:
+			break;
+		}
+	}
+
+	for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_XGMII:
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+			fm_info_set_mdio(i, dev);
+			break;
+		default:
+			break;
+		}
+	}
+
+#if (CONFIG_SYS_NUM_FMAN == 2)
+	if (srds_prtcl_s2 == 56) {
+		/* SGMII && XFI */
+		fm_info_set_phy_address(FM2_DTSEC1, SGMII_PHY_ADDR5);
+		fm_info_set_phy_address(FM2_DTSEC2, SGMII_PHY_ADDR6);
+		fm_info_set_phy_address(FM2_DTSEC3, SGMII_PHY_ADDR7);
+		fm_info_set_phy_address(FM2_DTSEC4, SGMII_PHY_ADDR8);
+		fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_10GEC2, FM1_10GEC2_PHY_ADDR);
+		fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC2_PHY_ADDR);
+		fm_info_set_phy_address(FM2_10GEC2, FM2_10GEC1_PHY_ADDR);
+	} else {
+		puts("Invalid SerDes2 protocol for T4240RDB\n");
+	}
+
+	for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
+		interface = fm_info_get_enet_if(i);
+		switch (interface) {
+		case PHY_INTERFACE_MODE_SGMII:
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+			fm_info_set_mdio(i, dev);
+			break;
+		default:
+			break;
+		}
+	}
+
+	for (i = FM2_10GEC1; i < FM2_10GEC1 + CONFIG_SYS_NUM_FM2_10GEC; i++) {
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_XGMII:
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+			fm_info_set_mdio(i, dev);
+			break;
+		default:
+			break;
+		}
+	}
+#endif /* CONFIG_SYS_NUM_FMAN */
+
+	cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+	return pci_eth_init(bis);
+}
diff --git a/board/freescale/t4rdb/law.c b/board/freescale/t4rdb/law.c
new file mode 100644
index 0000000..1f58768
--- /dev/null
+++ b/board/freescale/t4rdb/law.c
@@ -0,0 +1,28 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	/* Limit DCSR to 32M to access NPC Trace Buffer */
+	SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t4rdb/pci.c b/board/freescale/t4rdb/pci.c
new file mode 100644
index 0000000..6387a20
--- /dev/null
+++ b/board/freescale/t4rdb/pci.c
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+	FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t4rdb/t4240rdb.c b/board/freescale/t4rdb/t4240rdb.c
new file mode 100644
index 0000000..5448c86
--- /dev/null
+++ b/board/freescale/t4rdb/t4240rdb.c
@@ -0,0 +1,125 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "t4rdb.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	struct cpu_type *cpu = gd->arch.cpu;
+
+	printf("Board: %sRDB, ", cpu->name);
+
+	puts("SERDES Reference Clocks:\n");
+	printf("       SERDES1=100MHz SERDES2=156.25MHz\n"
+	       "       SERDES3=100MHz SERDES4=100MHz\n");
+
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash + PROMJET region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash + promjet */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+	set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+	setup_portals();
+#endif
+
+	return 0;
+}
+
+int misc_init_r(void)
+{
+	return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+	pci_of_setup(blob, bd);
+#endif
+
+	fdt_fixup_liodn(blob);
+	fdt_fixup_dr_usb(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+	fdt_fixup_fman_ethernet(blob);
+	fdt_fixup_board_enet(blob);
+#endif
+}
+
+/*
+ * This function is called by bdinfo to print detail board information.
+ * As an exmaple for future board, we organize the messages into
+ * several sections. If applicable, the message is in the format of
+ * <name>      = <value>
+ * It should aligned with normal output of bdinfo command.
+ *
+ * Voltage: Core, DDR and another configurable voltages
+ * Clock  : Critical clocks which are not printed already
+ * RCW    : RCW source if not printed already
+ * Misc   : Other important information not in above catagories
+ */
+void board_detail(void)
+{
+	int rcwsrc;
+
+	/* RCW section SW3[4] */
+	rcwsrc = 0x0;
+	puts("RCW source  = ");
+	switch (rcwsrc & 0x1) {
+	case 0x1:
+		puts("SDHC/eMMC\n");
+		break;
+	default:
+		puts("I2C normal addressing\n");
+		break;
+	}
+}
diff --git a/board/freescale/t4rdb/t4_pbi.cfg b/board/freescale/t4rdb/t4_pbi.cfg
new file mode 100644
index 0000000..c9f8ced
--- /dev/null
+++ b/board/freescale/t4rdb/t4_pbi.cfg
@@ -0,0 +1,31 @@
+#
+# Copyright 2014 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#512KB SRAM
+09010100 00000000
+09010104 fff80009
+09010f00 08000000
+#enable CPC1
+09010000 80000000
+#Configure LAW for CPC1
+09000d00 00000000
+09000d04 fff80000
+09000d08 81000012
+#slow mdio clock
+095fc030 00008148
+095fd030 00808148
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Flush PBL data
+09138000 00000000
+091380c0 00000000
diff --git a/board/freescale/t4rdb/t4_rcw.cfg b/board/freescale/t4rdb/t4_rcw.cfg
new file mode 100644
index 0000000..13408bd
--- /dev/null
+++ b/board/freescale/t4rdb/t4_rcw.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 010e0100
+#serdes protocol  28_56_2_10
+16070019 18101916 00000000 00000000
+70701050 00448c00 6c020000 f5000000
+00000000 ee0000ee 00000000 000287fc
+00000000 50000000 00000000 00000028
diff --git a/board/freescale/t4rdb/t4rdb.h b/board/freescale/t4rdb/t4rdb.h
new file mode 100644
index 0000000..fb25d43
--- /dev/null
+++ b/board/freescale/t4rdb/t4rdb.h
@@ -0,0 +1,18 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __T4RDB_H__
+#define __T4RDB_H__
+
+#undef CONFIG_SYS_NUM_FM1_DTSEC
+#undef CONFIG_SYS_NUM_FM2_DTSEC
+#define CONFIG_SYS_NUM_FM1_DTSEC	4
+#define CONFIG_SYS_NUM_FM2_DTSEC	4
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
diff --git a/board/freescale/t4rdb/tlb.c b/board/freescale/t4rdb/tlb.c
new file mode 100644
index 0000000..4b50bcd
--- /dev/null
+++ b/board/freescale/t4rdb/tlb.c
@@ -0,0 +1,111 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+	/*
+	 * *I*G - L3SRAM. When L3 is used as 512K SRAM */
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 0, BOOKE_PAGESZ_512K, 1),
+#else
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_16M, 1),
+
+	/* *I*G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000,
+		      CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_256M, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000,
+		      CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 5, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 6, BOOKE_PAGESZ_256K, 1),
+
+	/* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 9, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 10, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 11, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 12, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 13, BOOKE_PAGESZ_32M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+	/*
+	 * *I*G - NAND
+	 * entry 14 and 15 has been used hard coded, they will be disabled
+	 * in cpu_init_f, so we use entry 16 for nand.
+	 */
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 16, BOOKE_PAGESZ_64K, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/gen860t/fpga.c b/board/gen860t/fpga.c
index b7984dd..dd0ef70 100644
--- a/board/gen860t/fpga.c
+++ b/board/gen860t/fpga.c
@@ -40,7 +40,7 @@ DECLARE_GLOBAL_DATA_PTR;
 /* Note that these are pointers to code that is in Flash.  They will be
  * relocated at runtime.
  */
-Xilinx_Virtex2_Slave_SelectMap_fns fpga_fns = {
+xilinx_virtex2_slave_selectmap_fns fpga_fns = {
 	fpga_pre_config_fn,
 	fpga_pgm_fn,
 	fpga_init_fn,
@@ -56,8 +56,8 @@ Xilinx_Virtex2_Slave_SelectMap_fns fpga_fns = {
 	fpga_post_config_fn
 };
 
-Xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
-	{Xilinx_Virtex2,
+xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
+	{xilinx_virtex2,
 	 slave_selectmap,
 	 XILINX_XC2V3000_SIZE,
 	 (void *) &fpga_fns,
diff --git a/board/ip04/ip04.c b/board/ip04/ip04.c
index c8ae512..ae52633 100644
--- a/board/ip04/ip04.c
+++ b/board/ip04/ip04.c
@@ -13,7 +13,6 @@
 #include <common.h>
 #include <net.h>
 #include <netdev.h>
-#include <asm/net.h>
 
 int checkboard(void)
 {
@@ -33,7 +32,7 @@ int misc_init_r(void)
 	uchar enetaddr[6];
 	if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
 		puts("Warning: Generating 'random' MAC address\n");
-		bfin_gen_rand_mac(enetaddr);
+		eth_random_addr(enetaddr);
 		eth_setenv_enetaddr("ethaddr", enetaddr);
 	}
 
diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c
index 95a19cd..6bc8eb8 100644
--- a/board/keymile/kmp204x/kmp204x.c
+++ b/board/keymile/kmp204x/kmp204x.c
@@ -79,7 +79,7 @@ int get_scl(void)
 
 
 #define ZL30158_RST	8
-#define ZL30343_RST	9
+#define BFTIC4_RST	0
 
 int board_early_init_f(void)
 {
@@ -88,13 +88,15 @@ int board_early_init_f(void)
 	/* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */
 	setbits_be32(&gur->ddrclkdr, 0x001f000f);
 
-	/* take the Zarlinks out of reset as soon as possible */
-	qrio_prst(ZL30158_RST, false, false);
-	qrio_prst(ZL30343_RST, false, false);
+	/* set the BFTIC's prstcfg to reset at power-up and unit reset only */
+	qrio_prstcfg(BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST);
+	/* and enable WD on it */
+	qrio_wdmask(BFTIC4_RST, true);
 
-	/* and set their reset to power-up only */
-	qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST);
-	qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST);
+	/* set the ZL30138's prstcfg to reset at power-up and unit reset only */
+	qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_UNIT_RST);
+	/* and take it out of reset as soon as possible (needed for Hooper) */
+	qrio_prst(ZL30158_RST, false, false);
 
 	return 0;
 }
@@ -113,6 +115,12 @@ int board_early_init_r(void)
 	if (ret)
 		printf("error triggering PCIe FPGA config\n");
 
+	/* enable the Unit LED (red) & Boot LED (on) */
+	qrio_set_leds();
+
+	/* enable Application Buffer */
+	qrio_enable_app_buffer();
+
 	return ret;
 }
 
@@ -121,16 +129,37 @@ unsigned long get_board_sys_clk(unsigned long dummy)
 	return 66666666;
 }
 
+#define ETH_FRONT_PHY_RST	15
+#define QSFP2_RST		11
+#define QSFP1_RST		10
+#define ZL30343_RST		9
+
 int misc_init_f(void)
 {
 	/* configure QRIO pis for i2c deblocking */
 	i2c_deblock_gpio_cfg();
 
+	/* configure the front phy's prstcfg and take it out of reset */
+	qrio_prstcfg(ETH_FRONT_PHY_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+	qrio_prst(ETH_FRONT_PHY_RST, false, false);
+
+	/* set the ZL30343 prstcfg to reset at power-up and unit reset only */
+	qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_UNIT_RST);
+	/* and enable the WD on it */
+	qrio_wdmask(ZL30343_RST, true);
+
+	/* set the QSFPs' prstcfg to reset at power-up and unit rst only */
+	qrio_prstcfg(QSFP1_RST, PRSTCFG_POWUP_UNIT_RST);
+	qrio_prstcfg(QSFP2_RST, PRSTCFG_POWUP_UNIT_RST);
+
+	/* and enable the WD on them */
+	qrio_wdmask(QSFP1_RST, true);
+	qrio_wdmask(QSFP2_RST, true);
+
 	return 0;
 }
 
 #define NUM_SRDS_BANKS	2
-#define PHY_RST		15
 
 int misc_init_r(void)
 {
@@ -151,9 +180,6 @@ int misc_init_r(void)
 		}
 	}
 
-	/* take the mgmt eth phy out of reset */
-	qrio_prst(PHY_RST, false, false);
-
 	return 0;
 }
 
@@ -166,9 +192,23 @@ int hush_init_var(void)
 #endif
 
 #if defined(CONFIG_LAST_STAGE_INIT)
+
 int last_stage_init(void)
 {
+#if defined(CONFIG_KMCOGE4)
+	/* on KMCOGE4, the BFTIC4 is on the LBAPP2 */
+	struct bfticu_iomap *bftic4 =
+		(struct bfticu_iomap *)CONFIG_SYS_LBAPP2_BASE;
+	u8 dip_switch = in_8((u8 *)&(bftic4->mswitch)) & BFTICU_DIPSWITCH_MASK;
+
+	if (dip_switch != 0) {
+		/* start bootloader */
+		puts("DIP:   Enabled\n");
+		setenv("actual_bank", "0");
+	}
+#endif
 	set_km_env();
+
 	return 0;
 }
 #endif
@@ -232,3 +272,16 @@ void ft_board_setup(void *blob, bd_t *bd)
 	fdt_fixup_fman_mac_addresses(blob);
 #endif
 }
+
+#if defined(CONFIG_POST)
+
+/* DIC26_SELFTEST GPIO used to start factory test sw */
+#define SELFTEST_PORT	GPIO_A
+#define SELFTEST_PIN	31
+
+int post_hotkeys_pressed(void)
+{
+	qrio_gpio_direction_input(SELFTEST_PORT, SELFTEST_PIN);
+	return qrio_get_gpio(SELFTEST_PORT, SELFTEST_PIN);
+}
+#endif
diff --git a/board/keymile/kmp204x/kmp204x.h b/board/keymile/kmp204x/kmp204x.h
index 0267596..afede99 100644
--- a/board/keymile/kmp204x/kmp204x.h
+++ b/board/keymile/kmp204x/kmp204x.h
@@ -20,6 +20,9 @@ void qrio_gpio_direction_input(u8 port_off, u8 gpio_nr);
 #define PRSTCFG_POWUP_RST		0x3
 
 void qrio_prst(u8 bit, bool en, bool wden);
+void qrio_wdmask(u8 bit, bool wden);
 void qrio_prstcfg(u8 bit, u8 mode);
+void qrio_set_leds(void);
+void qrio_enable_app_buffer(void);
 
 void pci_of_setup(void *blob, bd_t *bd);
diff --git a/board/keymile/kmp204x/pbi.cfg b/board/keymile/kmp204x/pbi.cfg
index 9af8bd5..1e0a171 100644
--- a/board/keymile/kmp204x/pbi.cfg
+++ b/board/keymile/kmp204x/pbi.cfg
@@ -8,16 +8,47 @@
 #
 
 #PBI commands
-#Workaround for A-006559 needed for rev 2.0 of P2041 silicon
-#Freescale's errarta sheet suggests it may be done with PBI
+#Configure ALTCBAR for DCSR -> DCSR@89000000
+091380c0 000009C4
 09000010 00000000
+091380c0 000009C4
 09000014 00000000
+091380c0 000009C4
 09000018 81d00000
-09021008 0000f000
-09021028 0000f000
-09021048 0000f000
-09021068 0000f000
+#Workaround for A-004849
+091380c0 000009C4
+890B0050 00000002
+091380c0 000009C4
+890B0054 00000002
+091380c0 000009C4
+890B0058 00000002
+091380c0 000009C4
+890B005C 00000002
+091380c0 000009C4
+890B0090 00000002
+091380c0 000009C4
+890B0094 00000002
+091380c0 000009C4
+890B0098 00000002
+091380c0 000009C4
+890B009C 00000002
+091380c0 000009C4
+890B0108 00000012
+091380c0 000009C4
+#Workaround for A-006559 needed for rev 2.0 of P2041 silicon
+89021008 0000f000
+091380c0 000009C4
+89021028 0000f000
+091380c0 000009C4
+89021048 0000f000
+091380c0 000009C4
+89021068 0000f000
+091380c0 000009C4
+#Flush PBL data
+09138000 00000000
+#Disable ALTCBAR
 09000018 00000000
+091380c0 000009C4
 #Initialize CPC1 as 1MB SRAM
 09010000 00200400
 09138000 00000000
diff --git a/board/keymile/kmp204x/pci.c b/board/keymile/kmp204x/pci.c
index a484eb5..2b0b054 100644
--- a/board/keymile/kmp204x/pci.c
+++ b/board/keymile/kmp204x/pci.c
@@ -94,20 +94,23 @@ err_out:
 }
 
 #define PCIE_SW_RST	14
-#define PEXHC_SW_RST	13
-#define HOOPER_SW_RST	12
+#define PEXHC_RST	13
+#define HOOPER_RST	12
 
 void pci_init_board(void)
 {
-	/* first wait for the PCIe FPGA to be configured
+	qrio_prstcfg(PCIE_SW_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+	qrio_prstcfg(PEXHC_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+	qrio_prstcfg(HOOPER_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+
+	/* wait for the PCIe FPGA to be configured
 	 * it has been triggered earlier in board_early_init_r */
-	int ret = wait_for_fpga_config();
-	if (ret)
+	if (wait_for_fpga_config())
 		printf("error finishing PCIe FPGA config\n");
 
 	qrio_prst(PCIE_SW_RST, false, false);
-	qrio_prst(PEXHC_SW_RST, false, false);
-	qrio_prst(HOOPER_SW_RST, false, false);
+	qrio_prst(PEXHC_RST, false, false);
+	qrio_prst(HOOPER_RST, false, false);
 	/* Hooper is not direcly PCIe capable */
 	mdelay(50);
 
diff --git a/board/keymile/kmp204x/qrio.c b/board/keymile/kmp204x/qrio.c
index 49f9aa2..b6ba93a 100644
--- a/board/keymile/kmp204x/qrio.c
+++ b/board/keymile/kmp204x/qrio.c
@@ -91,7 +91,7 @@ void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val)
 
 #define WDMASK_OFF	0x16
 
-static void qrio_wdmask(u8 bit, bool wden)
+void qrio_wdmask(u8 bit, bool wden)
 {
 	u16 wdmask;
 	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
@@ -144,3 +144,32 @@ void qrio_prstcfg(u8 bit, u8 mode)
 
 	out_be32(qrio_base + PRSTCFG_OFF, prstcfg);
 }
+
+#define CTRLH_OFF		0x02
+#define CTRLH_WRL_BOOT		0x01
+#define CTRLH_WRL_UNITRUN	0x02
+
+void qrio_set_leds(void)
+{
+	u8 ctrlh;
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	/* set UNIT LED to RED and BOOT LED to ON */
+	ctrlh = in_8(qrio_base + CTRLH_OFF);
+	ctrlh |= (CTRLH_WRL_BOOT | CTRLH_WRL_UNITRUN);
+	out_8(qrio_base + CTRLH_OFF, ctrlh);
+}
+
+#define CTRLL_OFF		0x03
+#define CTRLL_WRB_BUFENA	0x20
+
+void qrio_enable_app_buffer(void)
+{
+	u8 ctrll;
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	/* enable application buffer */
+	ctrll = in_8(qrio_base + CTRLL_OFF);
+	ctrll |= (CTRLL_WRB_BUFENA);
+	out_8(qrio_base + CTRLL_OFF, ctrll);
+}
diff --git a/board/keymile/kmp204x/rcw_kmp204x.cfg b/board/keymile/kmp204x/rcw_kmp204x.cfg
index 2d4c48c..236d513 100644
--- a/board/keymile/kmp204x/rcw_kmp204x.cfg
+++ b/board/keymile/kmp204x/rcw_kmp204x.cfg
@@ -7,5 +7,5 @@ aa55aa55 010e0100
 #64 bytes RCW data
 14600000 00000000 28200000 00000000
 148E70CF CFC02000 58000000 41000000
-00000000 00000000 00000000 F0428002
+00000000 00000000 00000000 F0428816
 00000000 00000000 00000000 00000000
diff --git a/board/matrix_vision/mvsmr/fpga.c b/board/matrix_vision/mvsmr/fpga.c
index 88035a9..5189925 100644
--- a/board/matrix_vision/mvsmr/fpga.c
+++ b/board/matrix_vision/mvsmr/fpga.c
@@ -16,7 +16,7 @@
 #include "fpga.h"
 #include "mvsmr.h"
 
-Xilinx_Spartan3_Slave_Serial_fns fpga_fns = {
+xilinx_spartan3_slave_serial_fns fpga_fns = {
 	fpga_pre_config_fn,
 	fpga_pgm_fn,
 	fpga_clk_fn,
@@ -26,8 +26,8 @@ Xilinx_Spartan3_Slave_Serial_fns fpga_fns = {
 	0
 };
 
-Xilinx_desc spartan3 = {
-	Xilinx_Spartan2,
+xilinx_desc spartan3 = {
+	xilinx_spartan2,
 	slave_serial,
 	XILINX_XC3S200_SIZE,
 	(void *) &fpga_fns,
diff --git a/board/muas3001/muas3001.c b/board/muas3001/muas3001.c
index 42b0a03..08eb5e8 100644
--- a/board/muas3001/muas3001.c
+++ b/board/muas3001/muas3001.c
@@ -286,6 +286,8 @@ int board_early_init_r (void)
 }
 
 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
+DECLARE_GLOBAL_DATA_PTR;
+
 /*
  * update "memory" property in the blob
  */
@@ -314,7 +316,7 @@ void ft_blob_update (void *blob, bd_t *bd)
 	/* baudrate */
 	nodeoffset = fdt_path_offset (blob, "/soc/cpm/serial");
 	if (nodeoffset >= 0) {
-		speed = cpu_to_be32 (bd->bi_baudrate);
+		speed = cpu_to_be32 (gd->baudrate);
 		ret = fdt_setprop (blob, nodeoffset, "current-speed", &speed,
 					sizeof (unsigned long));
 	if (ret < 0)
diff --git a/board/mvblue/mvblue.c b/board/mvblue/mvblue.c
index 69abb06..63503e8 100644
--- a/board/mvblue/mvblue.c
+++ b/board/mvblue/mvblue.c
@@ -58,7 +58,6 @@ int checkboard (void)
 	u32 BoardType = get_BoardType ();
 	char *BoardName[2] = { "mvBlueBOX", "mvBlueLYNX" };
 	char *p;
-	bd_t *bd = gd->bd;
 
 	hw_watchdog_reset ();
 
@@ -71,8 +70,8 @@ int checkboard (void)
 	if ((p = getenv ("console_nr")) != NULL) {
 		unsigned long con_nr = simple_strtoul (p, NULL, 10) & 3;
 
-		bd->bi_baudrate &= ~3;
-		bd->bi_baudrate |= con_nr & 3;
+		gd->baudrate &= ~3;
+		gd->baudrate |= con_nr & 3;
 	}
 	return 0;
 }
diff --git a/board/sandbox/sandbox/Makefile b/board/sandbox/Makefile
index a0b9880..a0b9880 100644
--- a/board/sandbox/sandbox/Makefile
+++ b/board/sandbox/Makefile
diff --git a/board/sandbox/README.sandbox b/board/sandbox/README.sandbox
new file mode 100644
index 0000000..529c447
--- /dev/null
+++ b/board/sandbox/README.sandbox
@@ -0,0 +1,299 @@
+/*
+ * Copyright (c) 2014 The Chromium OS Authors.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+Native Execution of U-Boot
+==========================
+
+The 'sandbox' architecture is designed to allow U-Boot to run under Linux on
+almost any hardware. To achieve this it builds U-Boot (so far as possible)
+as a normal C application with a main() and normal C libraries.
+
+All of U-Boot's architecture-specific code therefore cannot be built as part
+of the sandbox U-Boot. The purpose of running U-Boot under Linux is to test
+all the generic code, not specific to any one architecture. The idea is to
+create unit tests which we can run to test this upper level code.
+
+CONFIG_SANDBOX is defined when building a native board.
+
+The chosen vendor and board names are also 'sandbox', so there is a single
+board in board/sandbox/sandbox.
+
+CONFIG_SANDBOX_BIG_ENDIAN should be defined when running on big-endian
+machines.
+
+Note that standalone/API support is not available at present.
+
+
+Basic Operation
+---------------
+
+To run sandbox U-Boot use something like:
+
+   make sandbox_config all
+   ./u-boot
+
+Note:
+   If you get errors about 'sdl-config: Command not found' you may need to
+   install libsdl1.2-dev or similar to get SDL support. Alternatively you can
+   build sandbox without SDL (i.e. no display/keyboard support) by removing
+   the CONFIG_SANDBOX_SDL line in include/configs/sandbox.h or using:
+
+      make sandbox_config all NO_SDL=1
+      ./u-boot
+
+
+U-Boot will start on your computer, showing a sandbox emulation of the serial
+console:
+
+
+U-Boot 2014.04 (Mar 20 2014 - 19:06:00)
+
+DRAM:  128 MiB
+Using default environment
+
+In:    serial
+Out:   lcd
+Err:   lcd
+=>
+
+You can issue commands as your would normally. If the command you want is
+not supported you can add it to include/configs/sandbox.h.
+
+To exit, type 'reset' or press Ctrl-C.
+
+
+Console / LCD support
+---------------------
+
+Assuming that CONFIG_SANDBOX_SDL is defined when building, you can run the
+sandbox with LCD and keyboard emulation, using something like:
+
+   ./u-boot -d u-boot.dtb -l
+
+This will start U-Boot with a window showing the contents of the LCD. If
+that window has the focus then you will be able to type commands as you
+would on the console. You can adjust the display settings in the device
+tree file - see arch/sandbox/dts/sandbox.dts.
+
+
+Command-line Options
+--------------------
+
+Various options are available, mostly for test purposes. Use -h to see
+available options. Some of these are described below.
+
+The terminal is normally in what is called 'raw-with-sigs' mode. This means
+that you can use arrow keys for command editing and history, but if you
+press Ctrl-C, U-Boot will exit instead of handling this as a keypress.
+
+Other options are 'raw' (so Ctrl-C is handled within U-Boot) and 'cooked'
+(where the terminal is in cooked mode and cursor keys will not work, Ctrl-C
+will exit).
+
+As mentioned above, -l causes the LCD emulation window to be shown.
+
+A device tree binary file can be provided with -d. If you edit the source
+(it is stored at arch/sandbox/dts/sandbox.dts) you must rebuild U-Boot to
+recreate the binary file.
+
+To execute commands directly, use the -c option. You can specify a single
+command, or multiple commands separated by a semicolon, as is normal in
+U-Boot. Be careful with quoting as the shall will normally process and
+swallow quotes. When -c is used, U-Boot exists after the command is complete,
+but you can force it to go to interactive mode instead with -i.
+
+
+Memory Emulation
+----------------
+
+Memory emulation is supported, with the size set by CONFIG_SYS_SDRAM_SIZE.
+The -m option can be used to read memory from a file on start-up and write
+it when shutting down. This allows preserving of memory contents across
+test runs. You can tell U-Boot to remove the memory file after it is read
+(on start-up) with the --rm_memory option.
+
+To access U-Boot's emulated memory within the code, use map_sysmem(). This
+function is used throughout U-Boot to ensure that emulated memory is used
+rather than the U-Boot application memory. This provides memory starting
+at 0 and extending to the size of the emulation.
+
+
+Storing State
+-------------
+
+With sandbox you can write drivers which emulate the operation of drivers on
+real devices. Some of these drivers may want to record state which is
+preserved across U-Boot runs. This is particularly useful for testing. For
+example, the contents of a SPI flash chip should not disappear just because
+U-Boot exits.
+
+State is stored in a device tree file in a simple format which is driver-
+specific. You then use the -s option to specify the state file. Use -r to
+make U-Boot read the state on start-up (otherwise it starts empty) and -w
+to write it on exit (otherwise the stored state is left unchanged and any
+changes U-Boot made will be lost). You can also use -n to tell U-Boot to
+ignore any problems with missing state. This is useful when first running
+since the state file will be empty.
+
+The device tree file has one node for each driver - the driver can store
+whatever properties it likes in there. See 'Writing Sandbox Drivers' below
+for more details on how to get drivers to read and write their state.
+
+
+Running and Booting
+-------------------
+
+Since there is no machine architecture, sandbox U-Boot cannot actually boot
+a kernel, but it does support the bootm command. Filesystems, memory
+commands, hashing, FIT images, verified boot and many other features are
+supported.
+
+When 'bootm' runs a kernel, sandbox will exit, as U-Boot does on a real
+machine. Of course in this case, no kernel is run.
+
+It is also possible to tell U-Boot that it has jumped from a temporary
+previous U-Boot binary, with the -j option. That binary is automatically
+removed by the U-Boot that gets the -j option. This allows you to write
+tests which emulate the action of chain-loading U-Boot, typically used in
+a situation where a second 'updatable' U-Boot is stored on your board. It
+is very risky to overwrite or upgrade the only U-Boot on a board, since a
+power or other failure will brick the board and require return to the
+manufacturer in the case of a consumer device.
+
+
+Supported Drivers
+-----------------
+
+U-Boot sandbox supports these emulations:
+
+- Block devices
+- Chrome OS EC
+- GPIO
+- Host filesystem (access files on the host from within U-Boot)
+- Keyboard (Chrome OS)
+- LCD
+- Serial (for console only)
+- Sound (incomplete - see sandbox_sdl_sound_init() for details)
+- SPI
+- SPI flash
+- TPM (Trusted Platform Module)
+
+Notable omissions are networking and I2C.
+
+A wide range of commands is implemented. Filesystems which use a block
+device are supported.
+
+Also sandbox uses generic board (CONFIG_SYS_GENERIC_BOARD) and supports
+driver model (CONFIG_DM) and associated commands.
+
+
+SPI Emulation
+-------------
+
+Sandbox supports SPI and SPI flash emulation.
+
+This is controlled by the spi_sf argument, the format of which is:
+
+   bus:cs:device:file
+
+   bus    - SPI bus number
+   cs     - SPI chip select number
+   device - SPI device emulation name
+   file   - File on disk containing the data
+
+For example:
+
+ dd if=/dev/zero of=spi.bin bs=1M count=4
+ ./u-boot --spi_sf 0:0:M25P16:spi.bin
+
+With this setup you can issue SPI flash commands as normal:
+
+=>sf probe
+SF: Detected M25P16 with page size 64 KiB, total 2 MiB
+=>sf read 0 0 10000
+SF: 65536 bytes @ 0x0 Read: OK
+=>
+
+Since this is a full SPI emulation (rather than just flash), you can
+also use low-level SPI commands:
+
+=>sspi 0:0 32 9f
+FF202015
+
+This is issuing a READ_ID command and getting back 20 (ST Micro) part
+0x2015 (the M25P16).
+
+Drivers are connected to a particular bus/cs using sandbox's state
+structure (see the 'spi' member). A set of operations must be provided
+for each driver.
+
+
+Configuration settings for the curious are:
+
+CONFIG_SANDBOX_SPI_MAX_BUS
+	The maximum number of SPI buses supported by the driver (default 1).
+
+CONFIG_SANDBOX_SPI_MAX_CS
+	The maximum number of chip selects supported by the driver
+	(default 10).
+
+CONFIG_SPI_IDLE_VAL
+	The idle value on the SPI bus
+
+
+Writing Sandbox Drivers
+-----------------------
+
+Generally you should put your driver in a file containing the word 'sandbox'
+and put it in the same directory as other drivers of its type. You can then
+implement the same hooks as the other drivers.
+
+To access U-Boot's emulated memory, use map_sysmem() as mentioned above.
+
+If your driver needs to store configuration or state (such as SPI flash
+contents or emulated chip registers), you can use the device tree as
+described above. Define handlers for this with the SANDBOX_STATE_IO macro.
+See arch/sandbox/include/asm/state.h for documentation. In short you provide
+a node name, compatible string and functions to read and write the state.
+Since writing the state can expand the device tree, you may need to use
+state_setprop() which does this automatically and avoids running out of
+space. See existing code for examples.
+
+
+Testing
+-------
+
+U-Boot sandbox can be used to run various tests, mostly in the test/
+directory. These include:
+
+  command_ut
+     - Unit tests for command parsing and handling
+  compression
+     - Unit tests for U-Boot's compression algorithms, useful for
+       security checking. It supports gzip, bzip2, lzma and lzo.
+  driver model
+     - test/dm/test-dm.sh to run these.
+  image
+     - Unit tests for images:
+          test/image/test-imagetools.sh - multi-file images
+          test/image/test-fit.py        - FIT images
+  tracing
+     - test/trace/test-trace.sh tests the tracing system (see README.trace)
+  verified boot
+      - See test/vboot/vboot_test.sh for this
+
+If you change or enhance any of the above subsystems, you shold write or
+expand a test and include it with your patch series submission. Test
+coverage in U-Boot is limited, as we need to work to improve it.
+
+Note that many of these tests are implemented as commands which you can
+run natively on your board if desired (and enabled).
+
+It would be useful to have a central script to run all of these.
+
+--
+Simon Glass <sjg@chromium.org>
+Updated 22-Mar-14
diff --git a/board/sandbox/sandbox/sandbox.c b/board/sandbox/sandbox.c
index e4d4e02..e4d4e02 100644
--- a/board/sandbox/sandbox/sandbox.c
+++ b/board/sandbox/sandbox.c
diff --git a/board/sandbox/sandbox/README.sandbox b/board/sandbox/sandbox/README.sandbox
deleted file mode 100644
index 6989557..0000000
--- a/board/sandbox/sandbox/README.sandbox
+++ /dev/null
@@ -1,91 +0,0 @@
-/*
- * Copyright (c) 2011 The Chromium OS Authors.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-Native Execution of U-Boot
-==========================
-
-The 'sandbox' architecture is designed to allow U-Boot to run under Linux on
-almost any hardware. To achieve this it builds U-Boot (so far as possible)
-as a normal C application with a main() and normal C libraries.
-
-All of U-Boot's architecture-specific code therefore cannot be built as part
-of the sandbox U-Boot. The purpose of running U-Boot under Linux is to test
-all the generic code, not specific to any one architecture. The idea is to
-create unit tests which we can run to test this upper level code.
-
-CONFIG_SANDBOX is defined when building a native board.
-
-The chosen vendor and board names are also 'sandbox', so there is a single
-board in board/sandbox/sandbox.
-
-CONFIG_SANDBOX_BIG_ENDIAN should be defined when running on big-endian
-machines.
-
-Note that standalone/API support is not available at present.
-
-The serial driver is a very simple implementation which reads and writes to
-the console. It does not set the terminal into raw mode, so cursor keys and
-history will not work yet.
-
-
-SPI Emulation
--------------
-
-Sandbox supports SPI and SPI flash emulation.
-
-This is controlled by the spi_sf argument, the format of which is:
-
-   bus:cs:device:file
-
-   bus    - SPI bus number
-   cs     - SPI chip select number
-   device - SPI device emulation name
-   file   - File on disk containing the data
-
-For example:
-
- dd if=/dev/zero of=spi.bin bs=1M count=4
- ./u-boot --spi_sf 0:0:M25P16:spi.bin
-
-With this setup you can issue SPI flash commands as normal:
-
-=>sf probe
-SF: Detected M25P16 with page size 64 KiB, total 2 MiB
-=>sf read 0 0 10000
-SF: 65536 bytes @ 0x0 Read: OK
-=>
-
-Since this is a full SPI emulation (rather than just flash), you can
-also use low-level SPI commands:
-
-=>sspi 0:0 32 9f
-FF202015
-
-This is issuing a READ_ID command and getting back 20 (ST Micro) part
-0x2015 (the M25P16).
-
-Drivers are connected to a particular bus/cs using sandbox's state
-structure (see the 'spi' member). A set of operations must be provided
-for each driver.
-
-
-Configuration settings for the curious are:
-
-CONFIG_SANDBOX_SPI_MAX_BUS
-	The maximum number of SPI buses supported by the driver (default 1).
-
-CONFIG_SANDBOX_SPI_MAX_CS
-	The maximum number of chip selects supported by the driver
-	(default 10).
-
-CONFIG_SPI_IDLE_VAL
-	The idle value on the SPI bus
-
-
-Tests
------
-
-So far we have no tests, but when we do these will be documented here.
diff --git a/board/spear/x600/fpga.c b/board/spear/x600/fpga.c
index c06c994..b256222 100644
--- a/board/spear/x600/fpga.c
+++ b/board/spear/x600/fpga.c
@@ -163,7 +163,7 @@ static int fpga_wr_fn(int assert_write, int flush, int cookie)
 	return assert_write;
 }
 
-static Xilinx_Spartan3_Slave_Serial_fns x600_fpga_fns = {
+static xilinx_spartan3_slave_serial_fns x600_fpga_fns = {
 	fpga_pre_config_fn,
 	fpga_pgm_fn,
 	fpga_clk_fn,
@@ -173,7 +173,7 @@ static Xilinx_Spartan3_Slave_Serial_fns x600_fpga_fns = {
 	fpga_post_config_fn,
 };
 
-static Xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
+static xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
 	XILINX_XC3S1200E_DESC(slave_serial, &x600_fpga_fns, 0)
 };
 
diff --git a/board/tcm-bf518/tcm-bf518.c b/board/tcm-bf518/tcm-bf518.c
index 5964059..5d25fcd 100644
--- a/board/tcm-bf518/tcm-bf518.c
+++ b/board/tcm-bf518/tcm-bf518.c
@@ -11,7 +11,6 @@
 #include <net.h>
 #include <netdev.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 #include <asm/mach-common/bits/otp.h>
 #include <asm/sdh.h>
 
@@ -47,7 +46,7 @@ static void board_init_enetaddr(uchar *mac_addr)
 
 	if (!valid_mac) {
 		puts("Warning: Generating 'random' MAC address\n");
-		bfin_gen_rand_mac(mac_addr);
+		eth_random_addr(mac_addr);
 	}
 
 	eth_setenv_enetaddr("ethaddr", mac_addr);
diff --git a/board/tcm-bf537/tcm-bf537.c b/board/tcm-bf537/tcm-bf537.c
index 38aaae6..a4f0f71 100644
--- a/board/tcm-bf537/tcm-bf537.c
+++ b/board/tcm-bf537/tcm-bf537.c
@@ -12,7 +12,6 @@
 #include <net.h>
 #include <netdev.h>
 #include <asm/blackfin.h>
-#include <asm/net.h>
 #include "../cm-bf537e/gpio_cfi_flash.h"
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -32,7 +31,7 @@ static void board_init_enetaddr(char *var)
 		return;
 
 	printf("Warning: %s: generating 'random' MAC address\n", var);
-	bfin_gen_rand_mac(enetaddr);
+	eth_random_addr(enetaddr);
 	eth_setenv_enetaddr(var, enetaddr);
 }
 
diff --git a/board/teejet/mt_ventoux/mt_ventoux.c b/board/teejet/mt_ventoux/mt_ventoux.c
index c32d554..b4a0a72 100644
--- a/board/teejet/mt_ventoux/mt_ventoux.c
+++ b/board/teejet/mt_ventoux/mt_ventoux.c
@@ -190,7 +190,7 @@ int fpga_clk_fn(int assert_clk, int flush, int cookie)
 	return assert_clk;
 }
 
-Xilinx_Spartan3_Slave_Serial_fns mt_ventoux_fpga_fns = {
+xilinx_spartan3_slave_serial_fns mt_ventoux_fpga_fns = {
 	fpga_pre_config_fn,
 	fpga_pgm_fn,
 	fpga_clk_fn,
@@ -200,7 +200,7 @@ Xilinx_Spartan3_Slave_Serial_fns mt_ventoux_fpga_fns = {
 	fpga_post_config_fn,
 };
 
-Xilinx_desc fpga = XILINX_XC6SLX4_DESC(slave_serial,
+xilinx_desc fpga = XILINX_XC6SLX4_DESC(slave_serial,
 			(void *)&mt_ventoux_fpga_fns, 0);
 
 /* Initialize the FPGA */
diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
index 485a5e4..c8cc2bc 100644
--- a/board/xilinx/zynq/board.c
+++ b/board/xilinx/zynq/board.c
@@ -14,15 +14,15 @@
 DECLARE_GLOBAL_DATA_PTR;
 
 #ifdef CONFIG_FPGA
-Xilinx_desc fpga;
+xilinx_desc fpga;
 
 /* It can be done differently */
-Xilinx_desc fpga010 = XILINX_XC7Z010_DESC(0x10);
-Xilinx_desc fpga015 = XILINX_XC7Z015_DESC(0x15);
-Xilinx_desc fpga020 = XILINX_XC7Z020_DESC(0x20);
-Xilinx_desc fpga030 = XILINX_XC7Z030_DESC(0x30);
-Xilinx_desc fpga045 = XILINX_XC7Z045_DESC(0x45);
-Xilinx_desc fpga100 = XILINX_XC7Z100_DESC(0x100);
+xilinx_desc fpga010 = XILINX_XC7Z010_DESC(0x10);
+xilinx_desc fpga015 = XILINX_XC7Z015_DESC(0x15);
+xilinx_desc fpga020 = XILINX_XC7Z020_DESC(0x20);
+xilinx_desc fpga030 = XILINX_XC7Z030_DESC(0x30);
+xilinx_desc fpga045 = XILINX_XC7Z045_DESC(0x45);
+xilinx_desc fpga100 = XILINX_XC7Z100_DESC(0x100);
 #endif
 
 int board_init(void)