Merge branch 'master' of git://git.denx.de/u-boot-arm

14 files changed, 610 insertions, 857 deletions

diff --git a/board/atmel/at91sam9x5ek/at91sam9x5ek.c b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
index 06028aa..edb0886 100644
--- a/board/atmel/at91sam9x5ek/at91sam9x5ek.c
+++ b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
@@ -31,6 +31,7 @@
 #include <asm/arch/clk.h>
 #include <lcd.h>
 #include <atmel_hlcdc.h>
+#include <atmel_mci.h>
 #ifdef CONFIG_MACB
 #include <net.h>
 #endif
@@ -258,6 +259,15 @@ void spi_cs_deactivate(struct spi_slave *slave)
 }
 #endif /* CONFIG_ATMEL_SPI */
 
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+int board_mmc_init(bd_t *bd)
+{
+	at91_mci_hw_init();
+
+	return atmel_mci_init((void *)ATMEL_BASE_HSMCI0);
+}
+#endif
+
 int board_early_init_f(void)
 {
 	at91_seriald_hw_init();
diff --git a/board/htkw/mcx/mcx.c b/board/htkw/mcx/mcx.c
index 7c9d34a..9fe6408 100644
--- a/board/htkw/mcx/mcx.c
+++ b/board/htkw/mcx/mcx.c
@@ -27,6 +27,8 @@
 #include <asm/mach-types.h>
 #include <asm/gpio.h>
 #include <asm/omap_gpio.h>
+#include <asm/arch/dss.h>
+#include <asm/arch/clocks.h>
 #include "errno.h"
 #include <i2c.h>
 #ifdef CONFIG_USB_EHCI
@@ -37,12 +39,16 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#define HOT_WATER_BUTTON	38
+#define HOT_WATER_BUTTON	42
+#define LCD_OUTPUT		55
+
+/* Address of the framebuffer in RAM. */
+#define FB_START_ADDRESS 0x88000000
 
 #ifdef CONFIG_USB_EHCI
 static struct omap_usbhs_board_data usbhs_bdata = {
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
 	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
 };
 
@@ -67,6 +73,8 @@ int board_init(void)
 	/* boot param addr */
 	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
 
+	gpio_direction_output(LCD_OUTPUT, 0);
+
 	return 0;
 }
 
@@ -87,6 +95,7 @@ int board_late_init(void)
 		return 0;
 
 	setenv("bootcmd", "run swupdate");
+
 	return 0;
 }
 #endif
@@ -109,15 +118,34 @@ int board_mmc_init(bd_t *bis)
 }
 #endif
 
-#ifdef CONFIG_USB_EHCI_OMAP
-#define USB_HOST_PWR_EN		132
-int board_usb_init(void)
+#if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD)
+
+static struct panel_config lcd_cfg = {
+	.timing_h       = PANEL_TIMING_H(40, 40, 48),
+	.timing_v       = PANEL_TIMING_V(29, 13, 3),
+	.pol_freq       = 0x00003000, /* Pol Freq */
+	.divisor        = 0x0001000E,
+	.panel_type     = 0x01, /* TFT */
+	.data_lines     = 0x03, /* 24 Bit RGB */
+	.load_mode      = 0x02, /* Frame Mode */
+	.panel_color	= 0,
+	.lcd_size	= PANEL_LCD_SIZE(800, 480),
+};
+
+int board_video_init(void)
 {
-	if (gpio_request(USB_HOST_PWR_EN, "USB_HOST_PWR_EN") < 0) {
-		puts("Failed to get USB_HOST_PWR_EN pin\n");
-		return -ENODEV;
-	}
-	gpio_direction_output(USB_HOST_PWR_EN, 1);
+	struct prcm *prcm_base = (struct prcm *)PRCM_BASE;
+	void *fb;
+
+	fb = (void *)FB_START_ADDRESS;
+
+	lcd_cfg.frame_buffer = fb;
+
+	setbits_le32(&prcm_base->fclken_dss, FCK_DSS_ON);
+	setbits_le32(&prcm_base->iclken_dss, ICK_DSS_ON);
+
+	omap3_dss_panel_config(&lcd_cfg);
+	omap3_dss_enable();
 
 	return 0;
 }
diff --git a/board/htkw/mcx/mcx.h b/board/htkw/mcx/mcx.h
index 867cc9e..0d4c642 100644
--- a/board/htkw/mcx/mcx.h
+++ b/board/htkw/mcx/mcx.h
@@ -96,7 +96,7 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(GPMC_A7),		(IEN | PTU | EN  | M4)) \
 	MUX_VAL(CP(GPMC_A8),		(IEN | PTU | EN  | M4)) \
 	MUX_VAL(CP(GPMC_A9),		(IEN | PTU | EN  | M4)) \
-	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | DIS | M4)) \
+	MUX_VAL(CP(GPMC_A10),		(IEN | PTU | EN | M4)) \
 					/* GPIO_43 LCD buffer enable */ \
 	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)) \
 	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)) \
@@ -143,28 +143,28 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0)) \
-	MUX_VAL(CP(DSS_DATA0),		(IEN | PTU | EN  | M4))\
-	MUX_VAL(CP(DSS_DATA1),		(IEN | PTU | EN  | M4)) \
-	MUX_VAL(CP(DSS_DATA2),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA0),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA1),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA2),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA3),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA4),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA5),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0)) \
-	MUX_VAL(CP(DSS_DATA8),		(IEN | PTU | EN  | M4)) \
-	MUX_VAL(CP(DSS_DATA9),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA8),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA9),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0)) \
-	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0))\
-	MUX_VAL(CP(DSS_DATA16),		(IEN | PTU | EN  | M4)) \
-	MUX_VAL(CP(DSS_DATA17),		(IEN | PTU | EN  | M4)) \
-	MUX_VAL(CP(DSS_DATA18),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA16),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA17),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA18),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA19),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA20),		(IDIS | PTD | DIS | M0)) \
-	MUX_VAL(CP(DSS_DATA21),		(IDIS | PTD | DIS | M0))  \
+	MUX_VAL(CP(DSS_DATA21),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA22),		(IDIS | PTD | DIS | M0)) \
 	MUX_VAL(CP(DSS_DATA23),		(IDIS | PTD | DIS | M0)) \
 	/* CAMERA */\
@@ -264,6 +264,8 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)) \
 	MUX_VAL(CP(I2C4_SCL),		(IEN  | PTU | EN  | M0)) \
 	MUX_VAL(CP(I2C4_SDA),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(HDQ_SIO),		(IEN  | PTU | EN  | M4)) \
+					/* GPIO_170 Touchscreen ISR */\
 	/* McSPI */\
 	MUX_VAL(CP(MCSPI1_CLK),		(IEN  | PTD | DIS | M0)) \
 	MUX_VAL(CP(MCSPI1_SIMO),	(IEN  | PTD | DIS | M0)) \
@@ -313,11 +315,11 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(RMII_TXEN),		(PTD | M0)) \
 	MUX_VAL(CP(RMII_50MHZ_CLK),	(IEN  | PTD | EN  | M0)) \
 	/* HECC */\
-	MUX_VAL(CP(HECC1_TXD),		(IEN  | PTD | EN  | M4)) \
-	MUX_VAL(CP(HECC1_RXD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(HECC1_TXD),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(HECC1_RXD),		(IEN  | PTD | EN  | M0)) \
 	/* HSUSB */\
 	MUX_VAL(CP(HSUSB0_CLK),		(IEN  | PTD | DIS | M0)) \
-	MUX_VAL(CP(HSUSB0_STP),		(IDIS | PTU | EN  | M0)) \
+	MUX_VAL(CP(HSUSB0_STP),		(IEN  | PTU | DIS  | M0)) \
 	MUX_VAL(CP(HSUSB0_DIR),		(IEN  | PTD | DIS | M0)) \
 	MUX_VAL(CP(HSUSB0_NXT),		(IEN  | PTD | DIS | M0)) \
 	MUX_VAL(CP(HSUSB0_DATA0),	(IEN  | PTD | DIS | M0)) \
diff --git a/board/samsung/origen/lowlevel_init.S b/board/samsung/origen/lowlevel_init.S
index 9283201..9daa0da 100644
--- a/board/samsung/origen/lowlevel_init.S
+++ b/board/samsung/origen/lowlevel_init.S
@@ -158,7 +158,22 @@ system_clock_init:
 	ldr	r2, =CLK_SRC_PERIL0_OFFSET
 	str	r1, [r0, r2]
 
-	/* FIMD0 */
+	/* CAM , FIMC 0-3 */
+	ldr	r1, =CLK_SRC_CAM_VAL
+	ldr	r2, =CLK_SRC_CAM_OFFSET
+	str	r1, [r0, r2]
+
+	/* MFC */
+	ldr	r1, =CLK_SRC_MFC_VAL
+	ldr	r2, =CLK_SRC_MFC_OFFSET
+	str	r1, [r0, r2]
+
+	/* G3D */
+	ldr	r1, =CLK_SRC_G3D_VAL
+	ldr	r2, =CLK_SRC_G3D_OFFSET
+	str	r1, [r0, r2]
+
+	/* LCD0 */
 	ldr	r1, =CLK_SRC_LCD0_VAL
 	ldr	r2, =CLK_SRC_LCD0_OFFSET
 	str	r1, [r0, r2]
@@ -223,6 +238,26 @@ system_clock_init:
 	ldr	r2, =CLK_DIV_PERIL0_OFFSET
 	str	r1, [r0, r2]
 
+	/* CAM, FIMC 0-3: CAM Clock Divisors */
+	ldr	r1, =CLK_DIV_CAM_VAL
+	ldr	r2, =CLK_DIV_CAM_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_MFC: MFC Clock Divisors */
+	ldr	r1, =CLK_DIV_MFC_VAL
+	ldr	r2, =CLK_DIV_MFC_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_G3D: G3D Clock Divisors */
+	ldr	r1, =CLK_DIV_G3D_VAL
+	ldr	r2, =CLK_DIV_G3D_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_LCD0: LCD0 Clock Divisors */
+	ldr	r1, =CLK_DIV_LCD0_VAL
+	ldr	r2, =CLK_DIV_LCD0_OFFSET
+	str	r1, [r0, r2]
+
 	/* Set PLL locktime */
 	ldr	r1, =PLL_LOCKTIME
 	ldr	r2, =APLL_LOCK_OFFSET
diff --git a/board/samsung/origen/origen_setup.h b/board/samsung/origen/origen_setup.h
index 94cccca..930b948 100644
--- a/board/samsung/origen/origen_setup.h
+++ b/board/samsung/origen/origen_setup.h
@@ -53,7 +53,18 @@
 #define CLK_DIV_FSYS2_OFFSET	0xC548
 #define CLK_DIV_FSYS3_OFFSET	0xC54C
 
+#define CLK_SRC_CAM_OFFSET	0xC220
+#define CLK_SRC_TV_OFFSET	0xC224
+#define CLK_SRC_MFC_OFFSET	0xC228
+#define CLK_SRC_G3D_OFFSET	0xC22C
+#define CLK_SRC_LCD0_OFFSET	0xC234
 #define CLK_SRC_PERIL0_OFFSET	0xC250
+
+#define CLK_DIV_CAM_OFFSET	0xC520
+#define CLK_DIV_TV_OFFSET	0xC524
+#define CLK_DIV_MFC_OFFSET	0xC528
+#define CLK_DIV_G3D_OFFSET	0xC52C
+#define CLK_DIV_LCD0_OFFSET	0xC534
 #define CLK_DIV_PERIL0_OFFSET	0xC550
 
 #define CLK_SRC_LCD0_OFFSET	0xC234
@@ -353,6 +364,65 @@
 				| (UART1_RATIO << 4) \
 				| (UART0_RATIO << 0))
 
+/* Clock Source CAM/FIMC */
+/* CLK_SRC_CAM */
+#define CAM0_SEL_XUSBXTI	1
+#define CAM1_SEL_XUSBXTI	1
+#define CSIS0_SEL_XUSBXTI	1
+#define CSIS1_SEL_XUSBXTI	1
+
+#define FIMC_SEL_SCLKMPLL	6
+#define FIMC0_LCLK_SEL		FIMC_SEL_SCLKMPLL
+#define FIMC1_LCLK_SEL		FIMC_SEL_SCLKMPLL
+#define FIMC2_LCLK_SEL		FIMC_SEL_SCLKMPLL
+#define FIMC3_LCLK_SEL		FIMC_SEL_SCLKMPLL
+
+#define CLK_SRC_CAM_VAL		((CSIS1_SEL_XUSBXTI << 28) \
+				| (CSIS0_SEL_XUSBXTI << 24) \
+				| (CAM1_SEL_XUSBXTI << 20) \
+				| (CAM0_SEL_XUSBXTI << 16) \
+				| (FIMC3_LCLK_SEL << 12) \
+				| (FIMC2_LCLK_SEL << 8) \
+				| (FIMC1_LCLK_SEL << 4) \
+				| (FIMC0_LCLK_SEL << 0))
+
+/* SCLK CAM */
+/* CLK_DIV_CAM */
+#define FIMC0_LCLK_RATIO	4
+#define FIMC1_LCLK_RATIO	4
+#define FIMC2_LCLK_RATIO	4
+#define FIMC3_LCLK_RATIO	4
+#define CLK_DIV_CAM_VAL		((FIMC3_LCLK_RATIO << 12) \
+				| (FIMC2_LCLK_RATIO << 8) \
+				| (FIMC1_LCLK_RATIO << 4) \
+				| (FIMC0_LCLK_RATIO << 0))
+
+/* SCLK MFC */
+/* CLK_SRC_MFC */
+#define MFC_SEL_MPLL		0
+#define MOUTMFC_0		0
+#define MFC_SEL			MOUTMFC_0
+#define MFC_0_SEL		MFC_SEL_MPLL
+#define CLK_SRC_MFC_VAL		((MFC_SEL << 8) | (MFC_0_SEL))
+
+
+/* CLK_DIV_MFC */
+#define MFC_RATIO		3
+#define CLK_DIV_MFC_VAL		(MFC_RATIO)
+
+/* SCLK G3D */
+/* CLK_SRC_G3D */
+#define G3D_SEL_MPLL		0
+#define MOUTG3D_0		0
+#define G3D_SEL			MOUTG3D_0
+#define G3D_0_SEL		G3D_SEL_MPLL
+#define CLK_SRC_G3D_VAL		((G3D_SEL << 8) | (G3D_0_SEL))
+
+/* CLK_DIV_G3D */
+#define G3D_RATIO		1
+#define CLK_DIV_G3D_VAL		(G3D_RATIO)
+
+/* SCLK LCD0 */
 /* CLK_SRC_LCD0 */
 #define FIMD_SEL_SCLKMPLL	6
 #define MDNIE0_SEL_XUSBXTI	1
@@ -363,6 +433,10 @@
 				| (MDNIE0_SEL_XUSBXTI << 4) \
 				| (FIMD_SEL_SCLKMPLL << 0))
 
+/* CLK_DIV_LCD0 */
+#define FIMD0_RATIO		4
+#define CLK_DIV_LCD0_VAL	(FIMD0_RATIO)
+
 /* Required period to generate a stable clock output */
 /* PLL_LOCK_TIME */
 #define PLL_LOCKTIME		0x1C20
diff --git a/board/sx1/Makefile b/board/sx1/Makefile
deleted file mode 100644
index 292459f..0000000
--- a/board/sx1/Makefile
+++ /dev/null
@@ -1,45 +0,0 @@
-#
-# (C) Copyright 2004-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).o
-
-COBJS	:= sx1.o
-SOBJS	:= lowlevel_init.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/sx1/config.mk b/board/sx1/config.mk
deleted file mode 100644
index 441bea2..0000000
--- a/board/sx1/config.mk
+++ /dev/null
@@ -1,19 +0,0 @@
-#
-# (C) Copyright 2004
-# Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
-#
-# SX1 board with OMAP1510 (ARM925T) cpu
-# see http://www.ti.com/ for more information on Texas Insturments
-#
-# SX1 has 1 bank of 256 MB SDRAM
-# Physical Address:
-# 1000'0000 to 2000'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000  (mem base + reserved)
-#
-# we load ourself to 1108'0000
-#
-#
-
-CONFIG_SYS_TEXT_BASE = 0x11080000
diff --git a/board/sx1/lowlevel_init.S b/board/sx1/lowlevel_init.S
deleted file mode 100644
index c1a811a..0000000
--- a/board/sx1/lowlevel_init.S
+++ /dev/null
@@ -1,397 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- *
- * -- Some bits of code used from rrload's head_OMAP1510.s --
- * Copyright (C) 2002 RidgeRun, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP1510)
-#include <./configs/omap1510.h>
-#endif
-
-#define OMAP1510_CLKS ((1<<EN_XORPCK)|(1<<EN_PERCK)|(1<<EN_TIMCK)|(1<<EN_GPIOCK))
-
-
-_TEXT_BASE:
-	.word	CONFIG_SYS_TEXT_BASE	 /* sdram load addr from config.mk */
-
-.globl lowlevel_init
-lowlevel_init:
-
-	/*
-	 * Configure 1510 pins functions to match our board.
-	 */
-	ldr	r0, REG_PULL_DWN_CTRL_0
-	ldr	r1, VAL_PULL_DWN_CTRL_0
-	str	r1, [r0]
-	ldr	r0, REG_PULL_DWN_CTRL_1
-	ldr	r1, VAL_PULL_DWN_CTRL_1
-	str	r1, [r0]
-	ldr	r0, REG_PULL_DWN_CTRL_2
-	ldr	r1, VAL_PULL_DWN_CTRL_2
-	str	r1, [r0]
-	ldr	r0, REG_PULL_DWN_CTRL_3
-	ldr	r1, VAL_PULL_DWN_CTRL_3
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_4
-	ldr	r1, VAL_FUNC_MUX_CTRL_4
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_5
-	ldr	r1, VAL_FUNC_MUX_CTRL_5
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_6
-	ldr	r1, VAL_FUNC_MUX_CTRL_6
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_7
-	ldr	r1, VAL_FUNC_MUX_CTRL_7
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_8
-	ldr	r1, VAL_FUNC_MUX_CTRL_8
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_9
-	ldr	r1, VAL_FUNC_MUX_CTRL_9
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_A
-	ldr	r1, VAL_FUNC_MUX_CTRL_A
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_B
-	ldr	r1, VAL_FUNC_MUX_CTRL_B
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_C
-	ldr	r1, VAL_FUNC_MUX_CTRL_C
-	str	r1, [r0]
-	ldr	r0, REG_FUNC_MUX_CTRL_D
-	ldr	r1, VAL_FUNC_MUX_CTRL_D
-	str	r1, [r0]
-	ldr	r0, REG_VOLTAGE_CTRL_0
-	ldr	r1, VAL_VOLTAGE_CTRL_0
-	str	r1, [r0]
-	ldr	r0, REG_TEST_DBG_CTRL_0
-	ldr	r1, VAL_TEST_DBG_CTRL_0
-	str	r1, [r0]
-	ldr	r0, REG_MOD_CONF_CTRL_0
-	ldr	r1, VAL_MOD_CONF_CTRL_0
-	str	r1, [r0]
-
-	/* Move to 1510 mode */
-	ldr	r0, REG_COMP_MODE_CTRL_0
-	ldr	r1, VAL_COMP_MODE_CTRL_0
-	str	r1, [r0]
-
-	/* Set up Traffic Ctlr*/
-	ldr r0, REG_TC_IMIF_PRIO
-	mov r1, #0x0
-	str r1, [r0]
-	ldr r0, REG_TC_EMIFS_PRIO
-	str r1, [r0]
-	ldr r0, REG_TC_EMIFF_PRIO
-	str r1, [r0]
-
-	ldr r0, REG_TC_EMIFS_CONFIG
-	ldr r1, [r0]
-	bic r1, r1, #0x08   /* clear the global power-down enable PDE bit */
-	bic r1, r1, #0x01   /* write protect flash by clearing the WP bit */
-	str r1, [r0]	    /* EMIFS GlB Configuration. (value 0x12 most likely) */
-
-	ldr r0, _GPIO_PIN_CONTROL_REG
-	mov r1,#0
-	orr r1, r1, #0x0001 /* M_PCM_SYNC */
-	orr r1, r1, #0x4000 /* IPC_ACTIVE */
-	strh r1,[r0]
-
-	ldr r0, _GPIO_DIR_CONTROL_REG
-	mov r1,#0
-	bic r1, r1, #0x0001 /* M_PCM_SYNC */
-	bic r1, r1, #0x4000 /* IPC_ACTIVE */
-	strh r1,[r0]
-
-	ldr r0, _GPIO_DATA_OUTPUT_REG
-	mov r1,#0
-	bic r1, r1, #0x0001 /* M_PCM_SYNC */
-	orr r1, r1, #0x4000 /* IPC_ACTIVE */
-	strh r1,[r0]
-
-	/* Setup some clock domains */
-	ldr r1, =OMAP1510_CLKS
-	ldr r0, REG_ARM_IDLECT2
-	strh r1, [r0]  /* CLKM, Clock domain control. */
-
-	mov r1, #0x01  /* PER_EN bit */
-	ldr r0, REG_ARM_RSTCT2
-	strh r1, [r0]  /* CLKM; Peripheral reset. */
-
-	/* Set CLKM to Sync-Scalable  */
-	/* I supposidly need to enable the dsp clock before switching */
-	mov r1, #0x1000
-	ldr r0, REG_ARM_SYSST
-	strh r1, [r0]
-	mov r0, #0x400
-1:
-	subs r0, r0, #0x1   /* wait for any bubbles to finish */
-	bne 1b
-
-	ldr r1, VAL_ARM_CKCTL  /* use 12Mhz ref, PER must be <= 50Mhz so /2 */
-	ldr r0, REG_ARM_CKCTL
-	strh r1, [r0]
-
-	/* setup DPLL 1 */
-	ldr r1, VAL_DPLL1_CTL
-	ldr r0, REG_DPLL1_CTL
-	strh r1, [r0]
-	ands r1, r1, #0x10  /* Check if PLL is enabled. */
-	beq lock_end	    /* Do not look for lock if BYPASS selected */
-2:
-	ldrh r1, [r0]
-	ands r1, r1, #0x01  /* Check the LOCK bit. */
-	beq 2b		    /* ...loop until bit goes hi. */
-lock_end:
-
-	/* Set memory timings corresponding to the new clock speed */
-
-	/* Check execution location to determine current execution location
-	 * and branch to appropriate initialization code.
-	 */
-	mov r0, #0x10000000		    /* Load physical SDRAM base. */
-	mov r1, pc			    /* Get current execution location. */
-	cmp r1, r0			    /* Compare. */
-	bge skip_sdram			    /* Skip over EMIF-fast initialization if running from SDRAM. */
-
-	/*
-	 * Delay for SDRAM initialization.
-	 */
-	mov r3, #0x1800			       /* value should be checked */
-3:
-	subs r3, r3, #0x1		      /* Decrement count */
-	bne 3b
-
-	/*
-	 * Set SDRAM control values. Disable refresh before MRS command.
-	 */
-	ldr r0, VAL_TC_EMIFF_SDRAM_CONFIG   /* get good value */
-	bic r3, r0, #0xC		    /* (BIT3|BIT2) ulConfig with auto-refresh disabled. */
-	orr r3, r3, #0x8000000		    /* (BIT27) Disable CLK when Power down or Self-Refresh */
-	orr r3, r3, #0x4000000		    /* BIT26 Power Down Enable */
-	ldr r2, REG_TC_EMIFF_SDRAM_CONFIG   /* Point to configuration register. */
-	str r3, [r2]			    /* Store the passed value with AR disabled. */
-
-	ldr r1, VAL_TC_EMIFF_MRS	    /* get MRS value */
-	ldr r2, REG_TC_EMIFF_MRS	    /* Point to MRS register. */
-	str r1, [r2]			    /* Store the passed value.*/
-
-	ldr r2, REG_TC_EMIFF_SDRAM_CONFIG   /* Point to configuration register. */
-	str r0, [r2]			    /* Store the passed value. */
-
-	/*
-	 * Delay for SDRAM initialization.
-	 */
-	mov r3, #0x1800
-4:
-	subs r3, r3, #1			    /* Decrement count. */
-	bne 4b
-
-skip_sdram:
-
-	/* slow interface */
-	ldr r1, VAL_TC_EMIFS_CS0_CONFIG
-	ldr r0, REG_TC_EMIFS_CS0_CONFIG
-	str r1, [r0] /* Chip Select 0 */
-	ldr r1, VAL_TC_EMIFS_CS1_CONFIG
-	ldr r0, REG_TC_EMIFS_CS1_CONFIG
-	str r1, [r0] /* Chip Select 1 */
-	ldr r1, VAL_TC_EMIFS_CS2_CONFIG
-	ldr r0, REG_TC_EMIFS_CS2_CONFIG
-	str r1, [r0] /* Chip Select 2 */
-	ldr r1, VAL_TC_EMIFS_CS3_CONFIG
-	ldr r0, REG_TC_EMIFS_CS3_CONFIG
-	str r1, [r0] /* Chip Select 3 */
-
-	/* back to arch calling code */
-	mov	pc, lr
-
-/* the literal pools origin */
-	.ltorg
-
-/* OMAP configuration registers */
-REG_FUNC_MUX_CTRL_0:		/* 32 bits */
-	.word 0xfffe1000
-REG_FUNC_MUX_CTRL_1:		/* 32 bits */
-	.word 0xfffe1004
-REG_FUNC_MUX_CTRL_2:		/* 32 bits */
-	.word 0xfffe1008
-REG_COMP_MODE_CTRL_0:		/* 32 bits */
-	.word 0xfffe100c
-REG_FUNC_MUX_CTRL_3:		/* 32 bits */
-	.word 0xfffe1010
-REG_FUNC_MUX_CTRL_4:		/* 32 bits */
-	.word 0xfffe1014
-REG_FUNC_MUX_CTRL_5:		/* 32 bits */
-	.word 0xfffe1018
-REG_FUNC_MUX_CTRL_6:		/* 32 bits */
-	.word 0xfffe101c
-REG_FUNC_MUX_CTRL_7:		/* 32 bits */
-	.word 0xfffe1020
-REG_FUNC_MUX_CTRL_8:		/* 32 bits */
-	.word 0xfffe1024
-REG_FUNC_MUX_CTRL_9:		/* 32 bits */
-	.word 0xfffe1028
-REG_FUNC_MUX_CTRL_A:		/* 32 bits */
-	.word 0xfffe102C
-REG_FUNC_MUX_CTRL_B:		/* 32 bits */
-	.word 0xfffe1030
-REG_FUNC_MUX_CTRL_C:		/* 32 bits */
-	.word 0xfffe1034
-REG_FUNC_MUX_CTRL_D:		/* 32 bits */
-	.word 0xfffe1038
-REG_PULL_DWN_CTRL_0:		/* 32 bits */
-	.word 0xfffe1040
-REG_PULL_DWN_CTRL_1:		/* 32 bits */
-	.word 0xfffe1044
-REG_PULL_DWN_CTRL_2:		/* 32 bits */
-	.word 0xfffe1048
-REG_PULL_DWN_CTRL_3:		/* 32 bits */
-	.word 0xfffe104c
-REG_VOLTAGE_CTRL_0:		/* 32 bits */
-	.word 0xfffe1060
-REG_TEST_DBG_CTRL_0:		/* 32 bits */
-	.word 0xfffe1070
-REG_MOD_CONF_CTRL_0:		/* 32 bits */
-	.word 0xfffe1080
-REG_TC_IMIF_PRIO:		/* 32 bits */
-	.word 0xfffecc00
-REG_TC_EMIFS_PRIO:		/* 32 bits */
-	.word 0xfffecc04
-REG_TC_EMIFF_PRIO:		/* 32 bits */
-	.word 0xfffecc08
-REG_TC_EMIFS_CONFIG:		/* 32 bits */
-	.word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG:	/* 32 bits */
-	.word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG:	/* 32 bits */
-	.word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG:	/* 32 bits */
-	.word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG:	/* 32 bits */
-	.word 0xfffecc1c
-REG_TC_EMIFF_SDRAM_CONFIG:	/* 32 bits */
-	.word 0xfffecc20
-REG_TC_EMIFF_MRS:		/* 32 bits */
-	.word 0xfffecc24
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL:			/* 16 bits */
-	.word 0xfffece00
-REG_ARM_IDLECT2:		/* 16 bits */
-	.word 0xfffece08
-REG_ARM_RSTCT2:			/* 16 bits */
-	.word 0xfffece14
-REG_ARM_SYSST:			/* 16 bits */
-	.word 0xfffece18
-/* DPLL control registers */
-REG_DPLL1_CTL:			/* 16 bits */
-	.word 0xfffecf00
-/* identification code register */
-REG_IDCODE:			/* 32 bits */
-	.word 0xfffed404
-
-/* SX1 specific */
-_GPIO_PIN_CONTROL_REG:
-	.word GPIO_PIN_CONTROL_REG
-_GPIO_DIR_CONTROL_REG:
-	.word GPIO_DIR_CONTROL_REG
-_GPIO_DATA_OUTPUT_REG:
-	.word GPIO_DATA_OUTPUT_REG
-
-VAL_COMP_MODE_CTRL_0:
-	.word 0x0000eaef
-VAL_FUNC_MUX_CTRL_4:
-	.word 0x00000000
-VAL_FUNC_MUX_CTRL_5:
-	.word 0x00000000
-VAL_FUNC_MUX_CTRL_6:
-	.word 0x00000001
-VAL_FUNC_MUX_CTRL_7:
-	.word 0x00001000
-VAL_FUNC_MUX_CTRL_8:
-	.word 0x00001240       /*[Knoller]  Value of Symbian Image Wing B2*/
-VAL_FUNC_MUX_CTRL_9:
-	.word 0x00201008
-VAL_FUNC_MUX_CTRL_A:
-	.word 0x00001000
-VAL_FUNC_MUX_CTRL_B:
-	.word 0x00000000
-VAL_FUNC_MUX_CTRL_C:
-	.word 0x09008001       /*[Knoller]  Value of Symbian Image Wing B2*/
-VAL_FUNC_MUX_CTRL_D:
-	.word 0x00000000
-VAL_PULL_DWN_CTRL_0:
-	.word 0xfffeffff
-VAL_PULL_DWN_CTRL_1:
-	.word 0xd1ffffec
-VAL_PULL_DWN_CTRL_2:
-	.word 0xffa80c5b
-VAL_PULL_DWN_CTRL_3:
-	.word 0xffffc0fe
-VAL_VOLTAGE_CTRL_0:
-	.word 0x00000007
-VAL_TEST_DBG_CTRL_0:
-	/* The OMAP5910 TRM says this register must be 0, but HelenConfRegs
-	 * says to write a 7.  Don't know what the right thing is to do, so
-	 * I'm leaving it at 7 since that's what was already here.
-	 */
-	.word 0x00000007
-VAL_MOD_CONF_CTRL_0:
-	.word 0x0da20000       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_ARM_CKCTL:
-	.word 0x010D
-
-VAL_DPLL1_CTL:
-	.word 0x3A33   /*[Hertle] Value of Symbian Image*/
-
-VAL_TC_EMIFS_CS1_CONFIG_PRELIM:
-	.word 0x00001149
-
-VAL_TC_EMIFS_CS2_CONFIG_PRELIM:
-	.word 0x00004158
-
-VAL_TC_EMIFS_CS0_CONFIG:
-	.word 0x00213090       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_TC_EMIFS_CS1_CONFIG:
-	.word 0x00215070       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_TC_EMIFS_CS2_CONFIG:
-	.word 0x00001139       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_TC_EMIFS_CS3_CONFIG:
-	.word 0x00001139       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-VAL_TC_EMIFF_SDRAM_CONFIG:
-	.word 0x0105f0b4       /*[Knoller]  Value of Symbian Image Wing B2*/
-
-
-VAL_TC_EMIFF_MRS:
-	.word 0x00000027       /*[Knoller]  Value of Symbian Image Wing B2*/
diff --git a/board/sx1/sx1.c b/board/sx1/sx1.c
deleted file mode 100644
index aaef76e..0000000
--- a/board/sx1/sx1.c
+++ /dev/null
@@ -1,123 +0,0 @@
-/*
- * (C) Copyright 2004
- * Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static void flash__init (void);
-static void ether__init (void);
-
-static inline void delay (unsigned long loops)
-{
-	__asm__ volatile ("1:\n"
-			  "subs %0, %1, #1\n"
-			  "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
-	/* arch number of SX1 Board */
-	gd->bd->bi_arch_number = MACH_TYPE_SX1;
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x10000100;
-
-/* kk - this speeds up your boot a quite a bit.	 However to make it
- *  work, you need make sure your kernel startup flush bug is fixed.
- *  ... rkw ...
- */
-	icache_enable ();
-
-	flash__init ();
-	ether__init ();
-	return 0;
-}
-
-
-int misc_init_r (void)
-{
-	/* volatile ushort *gdir = (ushort *) (GPIO_DIR_CONTROL_REG); */
-	/* volatile ushort *mdir = (ushort *) (MPUIO_DIR_CONTROL_REG); */
-
-	/* setup gpio direction to match board (no floats!) */
-	/**gdir = 0xCFF9; */
-	/**mdir = 0x103F; */
-
-	return (0);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-static void flash__init (void)
-{
-#define CS0_CHIP_SELECT_REG 0xfffecc10
-#define CS3_CHIP_SELECT_REG 0xfffecc1c
-#define EMIFS_GlB_Config_REG 0xfffecc0c
-
-	unsigned int regval;
-
-	regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
-	regval = regval | 0x0001;	/* Turn off write protection for flash devices. */
-	if (regval & 0x0002) {
-		regval = regval & 0xfffd;	/* Swap CS0 and CS3 so that flash is visible at 0x0 and eeprom at 0x0c000000. */
-		/* If, instead, you want to reference flash at 0x0c000000, then it seemed the following were necessary. */
-		/* *((volatile unsigned int *)CS0_CHIP_SELECT_REG) = 0x202090; / * Overrides head.S setting of 0x212090 */
-		/* *((volatile unsigned int *)CS3_CHIP_SELECT_REG) = 0x202090; / * Let's flash chips be fully functional. */
-	}
-	*((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
-}
-
-
-/******************************
- Routine:
- Description:
-******************************/
-static void ether__init (void)
-{
-#define ETH_CONTROL_REG 0x0800000b
-	/* take the Ethernet controller out of reset and wait
-	 * for the EEPROM load to complete.
-	 */
-	*((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
-	udelay (3);
-}
-
-
-int dram_init (void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
-}
diff --git a/board/teejet/mt_ventoux/mt_ventoux.c b/board/teejet/mt_ventoux/mt_ventoux.c
index ecb9b6c..9622a81 100644
--- a/board/teejet/mt_ventoux/mt_ventoux.c
+++ b/board/teejet/mt_ventoux/mt_ventoux.c
@@ -45,6 +45,8 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define BUZZER		140
 #define SPEAKER		141
+#define USB1_PWR	127
+#define USB2_PWR	149
 
 #ifndef CONFIG_FPGA
 #error "The Teejet mt_ventoux must have CONFIG_FPGA enabled"
@@ -247,6 +249,12 @@ int board_init(void)
 	gpio_direction_output(BUZZER, 0);
 	gpio_direction_output(SPEAKER, 0);
 
+	/* Activate USB power */
+	gpio_request(USB1_PWR, "USB1_PWR");
+	gpio_request(USB2_PWR, "USB2_PWR");
+	gpio_direction_output(USB1_PWR, 1);
+	gpio_direction_output(USB2_PWR, 1);
+
 	return 0;
 }
 
diff --git a/board/ti/am335x/Makefile b/board/ti/am335x/Makefile
index ca50eef..67a87a1 100644
--- a/board/ti/am335x/Makefile
+++ b/board/ti/am335x/Makefile
@@ -22,6 +22,7 @@ ifdef CONFIG_SPL_BUILD
 COBJS	:= mux.o
 endif
 
+COBJS	+= board.o
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
new file mode 100644
index 0000000..5d279ec
--- /dev/null
+++ b/board/ti/am335x/board.c
@@ -0,0 +1,376 @@
+/*
+ * board.c
+ *
+ * Board functions for TI AM335X based boards
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
+#ifdef CONFIG_SPL_BUILD
+static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
+#endif
+
+/* MII mode defines */
+#define MII_MODE_ENABLE		0x0
+#define RGMII_MODE_ENABLE	0xA
+
+/* GPIO that controls power to DDR on EVM-SK */
+#define GPIO_DDR_VTT_EN		7
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+static struct am335x_baseboard_id __attribute__((section (".data"))) header;
+
+static inline int board_is_bone(void)
+{
+	return !strncmp(header.name, "A335BONE", HDR_NAME_LEN);
+}
+
+static inline int board_is_bone_lt(void)
+{
+	return !strncmp(header.name, "A335BNLT", HDR_NAME_LEN);
+}
+
+static inline int board_is_evm_sk(void)
+{
+	return !strncmp("A335X_SK", header.name, HDR_NAME_LEN);
+}
+
+/*
+ * Read header information from EEPROM into global structure.
+ */
+static int read_eeprom(void)
+{
+	/* Check if baseboard eeprom is available */
+	if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) {
+		puts("Could not probe the EEPROM; something fundamentally "
+			"wrong on the I2C bus.\n");
+		return -ENODEV;
+	}
+
+	/* read the eeprom using i2c */
+	if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)&header,
+							sizeof(header))) {
+		puts("Could not read the EEPROM; something fundamentally"
+			" wrong on the I2C bus.\n");
+		return -EIO;
+	}
+
+	if (header.magic != 0xEE3355AA) {
+		/*
+		 * read the eeprom using i2c again,
+		 * but use only a 1 byte address
+		 */
+		if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1,
+					(uchar *)&header, sizeof(header))) {
+			puts("Could not read the EEPROM; something "
+				"fundamentally wrong on the I2C bus.\n");
+			return -EIO;
+		}
+
+		if (header.magic != 0xEE3355AA) {
+			printf("Incorrect magic number (0x%x) in EEPROM\n",
+					header.magic);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+/* UART Defines */
+#ifdef CONFIG_SPL_BUILD
+#define UART_RESET		(0x1 << 1)
+#define UART_CLK_RUNNING_MASK	0x1
+#define UART_SMART_IDLE_EN	(0x1 << 0x3)
+
+static void rtc32k_enable(void)
+{
+	struct rtc_regs *rtc = (struct rtc_regs *)AM335X_RTC_BASE;
+
+	/*
+	 * Unlock the RTC's registers.  For more details please see the
+	 * RTC_SS section of the TRM.  In order to unlock we need to
+	 * write these specific values (keys) in this order.
+	 */
+	writel(0x83e70b13, &rtc->kick0r);
+	writel(0x95a4f1e0, &rtc->kick1r);
+
+	/* Enable the RTC 32K OSC by setting bits 3 and 6. */
+	writel((1 << 3) | (1 << 6), &rtc->osc);
+}
+
+static const struct ddr_data ddr2_data = {
+	.datardsratio0 = ((MT47H128M16RT25E_RD_DQS<<30) |
+			  (MT47H128M16RT25E_RD_DQS<<20) |
+			  (MT47H128M16RT25E_RD_DQS<<10) |
+			  (MT47H128M16RT25E_RD_DQS<<0)),
+	.datawdsratio0 = ((MT47H128M16RT25E_WR_DQS<<30) |
+			  (MT47H128M16RT25E_WR_DQS<<20) |
+			  (MT47H128M16RT25E_WR_DQS<<10) |
+			  (MT47H128M16RT25E_WR_DQS<<0)),
+	.datawiratio0 = ((MT47H128M16RT25E_PHY_WRLVL<<30) |
+			 (MT47H128M16RT25E_PHY_WRLVL<<20) |
+			 (MT47H128M16RT25E_PHY_WRLVL<<10) |
+			 (MT47H128M16RT25E_PHY_WRLVL<<0)),
+	.datagiratio0 = ((MT47H128M16RT25E_PHY_GATELVL<<30) |
+			 (MT47H128M16RT25E_PHY_GATELVL<<20) |
+			 (MT47H128M16RT25E_PHY_GATELVL<<10) |
+			 (MT47H128M16RT25E_PHY_GATELVL<<0)),
+	.datafwsratio0 = ((MT47H128M16RT25E_PHY_FIFO_WE<<30) |
+			  (MT47H128M16RT25E_PHY_FIFO_WE<<20) |
+			  (MT47H128M16RT25E_PHY_FIFO_WE<<10) |
+			  (MT47H128M16RT25E_PHY_FIFO_WE<<0)),
+	.datawrsratio0 = ((MT47H128M16RT25E_PHY_WR_DATA<<30) |
+			  (MT47H128M16RT25E_PHY_WR_DATA<<20) |
+			  (MT47H128M16RT25E_PHY_WR_DATA<<10) |
+			  (MT47H128M16RT25E_PHY_WR_DATA<<0)),
+	.datauserank0delay = MT47H128M16RT25E_PHY_RANK0_DELAY,
+	.datadldiff0 = PHY_DLL_LOCK_DIFF,
+};
+
+static const struct cmd_control ddr2_cmd_ctrl_data = {
+	.cmd0csratio = MT47H128M16RT25E_RATIO,
+	.cmd0dldiff = MT47H128M16RT25E_DLL_LOCK_DIFF,
+	.cmd0iclkout = MT47H128M16RT25E_INVERT_CLKOUT,
+
+	.cmd1csratio = MT47H128M16RT25E_RATIO,
+	.cmd1dldiff = MT47H128M16RT25E_DLL_LOCK_DIFF,
+	.cmd1iclkout = MT47H128M16RT25E_INVERT_CLKOUT,
+
+	.cmd2csratio = MT47H128M16RT25E_RATIO,
+	.cmd2dldiff = MT47H128M16RT25E_DLL_LOCK_DIFF,
+	.cmd2iclkout = MT47H128M16RT25E_INVERT_CLKOUT,
+};
+
+static const struct emif_regs ddr2_emif_reg_data = {
+	.sdram_config = MT47H128M16RT25E_EMIF_SDCFG,
+	.ref_ctrl = MT47H128M16RT25E_EMIF_SDREF,
+	.sdram_tim1 = MT47H128M16RT25E_EMIF_TIM1,
+	.sdram_tim2 = MT47H128M16RT25E_EMIF_TIM2,
+	.sdram_tim3 = MT47H128M16RT25E_EMIF_TIM3,
+	.emif_ddr_phy_ctlr_1 = MT47H128M16RT25E_EMIF_READ_LATENCY,
+};
+
+static const struct ddr_data ddr3_data = {
+	.datardsratio0 = MT41J128MJT125_RD_DQS,
+	.datawdsratio0 = MT41J128MJT125_WR_DQS,
+	.datafwsratio0 = MT41J128MJT125_PHY_FIFO_WE,
+	.datawrsratio0 = MT41J128MJT125_PHY_WR_DATA,
+	.datadldiff0 = PHY_DLL_LOCK_DIFF,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+	.cmd0csratio = MT41J128MJT125_RATIO,
+	.cmd0dldiff = MT41J128MJT125_DLL_LOCK_DIFF,
+	.cmd0iclkout = MT41J128MJT125_INVERT_CLKOUT,
+
+	.cmd1csratio = MT41J128MJT125_RATIO,
+	.cmd1dldiff = MT41J128MJT125_DLL_LOCK_DIFF,
+	.cmd1iclkout = MT41J128MJT125_INVERT_CLKOUT,
+
+	.cmd2csratio = MT41J128MJT125_RATIO,
+	.cmd2dldiff = MT41J128MJT125_DLL_LOCK_DIFF,
+	.cmd2iclkout = MT41J128MJT125_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = MT41J128MJT125_EMIF_SDCFG,
+	.ref_ctrl = MT41J128MJT125_EMIF_SDREF,
+	.sdram_tim1 = MT41J128MJT125_EMIF_TIM1,
+	.sdram_tim2 = MT41J128MJT125_EMIF_TIM2,
+	.sdram_tim3 = MT41J128MJT125_EMIF_TIM3,
+	.zq_config = MT41J128MJT125_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41J128MJT125_EMIF_READ_LATENCY,
+};
+#endif
+
+/*
+ * early system init of muxing and clocks.
+ */
+void s_init(void)
+{
+	/* WDT1 is already running when the bootloader gets control
+	 * Disable it to avoid "random" resets
+	 */
+	writel(0xAAAA, &wdtimer->wdtwspr);
+	while (readl(&wdtimer->wdtwwps) != 0x0)
+		;
+	writel(0x5555, &wdtimer->wdtwspr);
+	while (readl(&wdtimer->wdtwwps) != 0x0)
+		;
+
+#ifdef CONFIG_SPL_BUILD
+	/* Setup the PLLs and the clocks for the peripherals */
+	pll_init();
+
+	/* Enable RTC32K clock */
+	rtc32k_enable();
+
+	/* UART softreset */
+	u32 regVal;
+
+	enable_uart0_pin_mux();
+
+	regVal = readl(&uart_base->uartsyscfg);
+	regVal |= UART_RESET;
+	writel(regVal, &uart_base->uartsyscfg);
+	while ((readl(&uart_base->uartsyssts) &
+		UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK)
+		;
+
+	/* Disable smart idle */
+	regVal = readl(&uart_base->uartsyscfg);
+	regVal |= UART_SMART_IDLE_EN;
+	writel(regVal, &uart_base->uartsyscfg);
+
+	gd = &gdata;
+
+	preloader_console_init();
+
+	/* Initalize the board header */
+	enable_i2c0_pin_mux();
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	if (read_eeprom() < 0)
+		puts("Could not get board ID.\n");
+
+	enable_board_pin_mux(&header);
+	if (board_is_evm_sk()) {
+		/*
+		 * EVM SK 1.2A and later use gpio0_7 to enable DDR3.
+		 * This is safe enough to do on older revs.
+		 */
+		gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
+		gpio_direction_output(GPIO_DDR_VTT_EN, 1);
+	}
+
+	if (board_is_evm_sk() || board_is_bone_lt())
+		config_ddr(303, MT41J128MJT125_IOCTRL_VALUE, &ddr3_data,
+			   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data);
+	else
+		config_ddr(266, MT47H128M16RT25E_IOCTRL_VALUE, &ddr2_data,
+			   &ddr2_cmd_ctrl_data, &ddr2_emif_reg_data);
+#endif
+}
+
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	if (read_eeprom() < 0)
+		puts("Could not get board ID.\n");
+
+	gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_id		= 0,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_id		= 1,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= AM335X_CPSW_MDIO_BASE,
+	.cpsw_base		= AM335X_CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+		debug("<ethaddr> not set. Reading from E-fuse\n");
+		/* try reading mac address from efuse */
+		mac_lo = readl(&cdev->macid0l);
+		mac_hi = readl(&cdev->macid0h);
+		mac_addr[0] = mac_hi & 0xFF;
+		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+		mac_addr[4] = mac_lo & 0xFF;
+		mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+		else
+			return -1;
+	}
+
+	if (board_is_bone() || board_is_bone_lt()) {
+		writel(MII_MODE_ENABLE, &cdev->miisel);
+		cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
+				PHY_INTERFACE_MODE_MII;
+	} else {
+		writel(RGMII_MODE_ENABLE, &cdev->miisel);
+		cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
+				PHY_INTERFACE_MODE_RGMII;
+	}
+
+	return cpsw_register(&cpsw_data);
+}
+#endif
diff --git a/board/ti/am335x/board.h b/board/ti/am335x/board.h
new file mode 100644
index 0000000..7985ab2
--- /dev/null
+++ b/board/ti/am335x/board.h
@@ -0,0 +1,49 @@
+/*
+ * board.h
+ *
+ * TI AM335x boards information header
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * TI AM335x parts define a system EEPROM that defines certain sub-fields.
+ * We use these fields to in turn see what board we are on, and what
+ * that might require us to set or not set.
+ */
+#define HDR_NO_OF_MAC_ADDR	3
+#define HDR_ETH_ALEN		6
+#define HDR_NAME_LEN		8
+
+struct am335x_baseboard_id {
+	unsigned int  magic;
+	char name[HDR_NAME_LEN];
+	char version[4];
+	char serial[12];
+	char config[32];
+	char mac_addr[HDR_NO_OF_MAC_ADDR][HDR_ETH_ALEN];
+};
+
+/*
+ * We have three pin mux functions that must exist.  We must be able to enable
+ * uart0, for initial output and i2c0 to read the main EEPROM.  We then have a
+ * main pinmux function that can be overridden to enable all other pinmux that
+ * is required on the board.
+ */
+void enable_uart0_pin_mux(void);
+void enable_i2c0_pin_mux(void);
+void enable_board_pin_mux(struct am335x_baseboard_id *header);
+#endif
diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c
index 80becd5..2992979 100644
--- a/board/ti/am335x/mux.c
+++ b/board/ti/am335x/mux.c
@@ -16,242 +16,10 @@
 #include <common.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
 #include <asm/io.h>
 #include <i2c.h>
-
-#define MUX_CFG(value, offset)	\
-	__raw_writel(value, (CTRL_BASE + offset));
-
-/* PAD Control Fields */
-#define SLEWCTRL	(0x1 << 6)
-#define RXACTIVE	(0x1 << 5)
-#define PULLUP_EN	(0x1 << 4) /* Pull UP Selection */
-#define PULLUDEN	(0x0 << 3) /* Pull up enabled */
-#define PULLUDDIS	(0x1 << 3) /* Pull up disabled */
-#define MODE(val)	val	/* used for Readability */
-
-/*
- * PAD CONTROL OFFSETS
- * Field names corresponds to the pad signal name
- */
-struct pad_signals {
-	int gpmc_ad0;
-	int gpmc_ad1;
-	int gpmc_ad2;
-	int gpmc_ad3;
-	int gpmc_ad4;
-	int gpmc_ad5;
-	int gpmc_ad6;
-	int gpmc_ad7;
-	int gpmc_ad8;
-	int gpmc_ad9;
-	int gpmc_ad10;
-	int gpmc_ad11;
-	int gpmc_ad12;
-	int gpmc_ad13;
-	int gpmc_ad14;
-	int gpmc_ad15;
-	int gpmc_a0;
-	int gpmc_a1;
-	int gpmc_a2;
-	int gpmc_a3;
-	int gpmc_a4;
-	int gpmc_a5;
-	int gpmc_a6;
-	int gpmc_a7;
-	int gpmc_a8;
-	int gpmc_a9;
-	int gpmc_a10;
-	int gpmc_a11;
-	int gpmc_wait0;
-	int gpmc_wpn;
-	int gpmc_be1n;
-	int gpmc_csn0;
-	int gpmc_csn1;
-	int gpmc_csn2;
-	int gpmc_csn3;
-	int gpmc_clk;
-	int gpmc_advn_ale;
-	int gpmc_oen_ren;
-	int gpmc_wen;
-	int gpmc_be0n_cle;
-	int lcd_data0;
-	int lcd_data1;
-	int lcd_data2;
-	int lcd_data3;
-	int lcd_data4;
-	int lcd_data5;
-	int lcd_data6;
-	int lcd_data7;
-	int lcd_data8;
-	int lcd_data9;
-	int lcd_data10;
-	int lcd_data11;
-	int lcd_data12;
-	int lcd_data13;
-	int lcd_data14;
-	int lcd_data15;
-	int lcd_vsync;
-	int lcd_hsync;
-	int lcd_pclk;
-	int lcd_ac_bias_en;
-	int mmc0_dat3;
-	int mmc0_dat2;
-	int mmc0_dat1;
-	int mmc0_dat0;
-	int mmc0_clk;
-	int mmc0_cmd;
-	int mii1_col;
-	int mii1_crs;
-	int mii1_rxerr;
-	int mii1_txen;
-	int mii1_rxdv;
-	int mii1_txd3;
-	int mii1_txd2;
-	int mii1_txd1;
-	int mii1_txd0;
-	int mii1_txclk;
-	int mii1_rxclk;
-	int mii1_rxd3;
-	int mii1_rxd2;
-	int mii1_rxd1;
-	int mii1_rxd0;
-	int rmii1_refclk;
-	int mdio_data;
-	int mdio_clk;
-	int spi0_sclk;
-	int spi0_d0;
-	int spi0_d1;
-	int spi0_cs0;
-	int spi0_cs1;
-	int ecap0_in_pwm0_out;
-	int uart0_ctsn;
-	int uart0_rtsn;
-	int uart0_rxd;
-	int uart0_txd;
-	int uart1_ctsn;
-	int uart1_rtsn;
-	int uart1_rxd;
-	int uart1_txd;
-	int i2c0_sda;
-	int i2c0_scl;
-	int mcasp0_aclkx;
-	int mcasp0_fsx;
-	int mcasp0_axr0;
-	int mcasp0_ahclkr;
-	int mcasp0_aclkr;
-	int mcasp0_fsr;
-	int mcasp0_axr1;
-	int mcasp0_ahclkx;
-	int xdma_event_intr0;
-	int xdma_event_intr1;
-	int nresetin_out;
-	int porz;
-	int nnmi;
-	int osc0_in;
-	int osc0_out;
-	int rsvd1;
-	int tms;
-	int tdi;
-	int tdo;
-	int tck;
-	int ntrst;
-	int emu0;
-	int emu1;
-	int osc1_in;
-	int osc1_out;
-	int pmic_power_en;
-	int rtc_porz;
-	int rsvd2;
-	int ext_wakeup;
-	int enz_kaldo_1p8v;
-	int usb0_dm;
-	int usb0_dp;
-	int usb0_ce;
-	int usb0_id;
-	int usb0_vbus;
-	int usb0_drvvbus;
-	int usb1_dm;
-	int usb1_dp;
-	int usb1_ce;
-	int usb1_id;
-	int usb1_vbus;
-	int usb1_drvvbus;
-	int ddr_resetn;
-	int ddr_csn0;
-	int ddr_cke;
-	int ddr_ck;
-	int ddr_nck;
-	int ddr_casn;
-	int ddr_rasn;
-	int ddr_wen;
-	int ddr_ba0;
-	int ddr_ba1;
-	int ddr_ba2;
-	int ddr_a0;
-	int ddr_a1;
-	int ddr_a2;
-	int ddr_a3;
-	int ddr_a4;
-	int ddr_a5;
-	int ddr_a6;
-	int ddr_a7;
-	int ddr_a8;
-	int ddr_a9;
-	int ddr_a10;
-	int ddr_a11;
-	int ddr_a12;
-	int ddr_a13;
-	int ddr_a14;
-	int ddr_a15;
-	int ddr_odt;
-	int ddr_d0;
-	int ddr_d1;
-	int ddr_d2;
-	int ddr_d3;
-	int ddr_d4;
-	int ddr_d5;
-	int ddr_d6;
-	int ddr_d7;
-	int ddr_d8;
-	int ddr_d9;
-	int ddr_d10;
-	int ddr_d11;
-	int ddr_d12;
-	int ddr_d13;
-	int ddr_d14;
-	int ddr_d15;
-	int ddr_dqm0;
-	int ddr_dqm1;
-	int ddr_dqs0;
-	int ddr_dqsn0;
-	int ddr_dqs1;
-	int ddr_dqsn1;
-	int ddr_vref;
-	int ddr_vtp;
-	int ddr_strben0;
-	int ddr_strben1;
-	int ain7;
-	int ain6;
-	int ain5;
-	int ain4;
-	int ain3;
-	int ain2;
-	int ain1;
-	int ain0;
-	int vrefp;
-	int vrefn;
-};
-
-struct module_pin_mux {
-	short reg_offset;
-	unsigned char val;
-};
-
-/* Pad control register offset */
-#define PAD_CTRL_BASE	0x800
-#define OFFSET(x)	(unsigned int) (&((struct pad_signals *) \
-				(PAD_CTRL_BASE))->x)
+#include "board.h"
 
 static struct module_pin_mux uart0_pin_mux[] = {
 	{OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* UART0_RXD */
@@ -362,20 +130,6 @@ static struct module_pin_mux mii1_pin_mux[] = {
 	{-1},
 };
 
-/*
- * Configure the pin mux for the module
- */
-static void configure_module_pin_mux(struct module_pin_mux *mod_pin_mux)
-{
-	int i;
-
-	if (!mod_pin_mux)
-		return;
-
-	for (i = 0; mod_pin_mux[i].reg_offset != -1; i++)
-		MUX_CFG(mod_pin_mux[i].val, mod_pin_mux[i].reg_offset);
-}
-
 void enable_uart0_pin_mux(void)
 {
 	configure_module_pin_mux(uart0_pin_mux);