summaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
authorWolfgang Denk <wd@denx.de>2010-09-08 00:42:00 +0200
committerWolfgang Denk <wd@denx.de>2010-09-08 00:42:00 +0200
commitcf64fda38e3d71e9077e11c673bd9be449c680da (patch)
treea847fb6cd48330482642ff92e34a7329b339acd2 /board
parent09b4a9cf4003599f2cd609587dfa5f0b754640ed (diff)
parent5c3dab97c751e43103813472283305cbfe70d3f0 (diff)
downloadu-boot-imx-cf64fda38e3d71e9077e11c673bd9be449c680da.zip
u-boot-imx-cf64fda38e3d71e9077e11c673bd9be449c680da.tar.gz
u-boot-imx-cf64fda38e3d71e9077e11c673bd9be449c680da.tar.bz2
Merge branch 'at91' of git://git.denx.de/u-boot-atmel
Diffstat (limited to 'board')
-rw-r--r--board/esd/meesc/meesc.c116
-rw-r--r--board/eukrea/cpuat91/cpuat91.c53
2 files changed, 84 insertions, 85 deletions
diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c
index 694bd74..41fa3e1 100644
--- a/board/esd/meesc/meesc.c
+++ b/board/esd/meesc/meesc.c
@@ -3,7 +3,7 @@
* Stelian Pop <stelian.pop@leadtechdesign.com>
* Lead Tech Design <www.leadtechdesign.com>
*
- * (C) Copyright 2009
+ * (C) Copyright 2009-2010
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
@@ -28,13 +28,13 @@
#include <common.h>
#include <asm/arch/at91sam9263.h>
-#include <asm/arch/at91sam9_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
+#include <asm/arch/at91_matrix.h>
+#include <asm/arch/at91_pio.h>
#include <asm/arch/clk.h>
-#include <asm/arch/gpio.h>
#include <asm/arch/hardware.h>
#include <asm/arch/io.h>
#include <netdev.h>
@@ -52,10 +52,10 @@ int get_hw_rev(void)
if (hw_rev >= 0)
return hw_rev;
- hw_rev = at91_get_gpio_value(AT91_PIN_PB19);
- hw_rev |= at91_get_gpio_value(AT91_PIN_PB20) << 1;
- hw_rev |= at91_get_gpio_value(AT91_PIN_PB21) << 2;
- hw_rev |= at91_get_gpio_value(AT91_PIN_PB22) << 3;
+ hw_rev = at91_get_pio_value(AT91_PIO_PORTB, 19);
+ hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 20) << 1;
+ hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 21) << 2;
+ hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 22) << 3;
if (hw_rev == 15)
hw_rev = 0;
@@ -67,44 +67,44 @@ int get_hw_rev(void)
static void meesc_nand_hw_init(void)
{
unsigned long csa;
+ at91_smc_t *smc = (at91_smc_t *) AT91_SMC0_BASE;
+ at91_matrix_t *matrix = (at91_matrix_t *) AT91_MATRIX_BASE;
/* Enable CS3 */
- csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
- at91_sys_write(AT91_MATRIX_EBI0CSA,
- csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
+ csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
+ writel(csa, &matrix->csa[0]);
/* Configure SMC CS3 for NAND/SmartMedia */
- at91_sys_write(AT91_SMC_SETUP(3),
- AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC_PULSE(3),
- AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
- AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
- at91_sys_write(AT91_SMC_CYCLE(3),
- AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
- at91_sys_write(AT91_SMC_MODE(3),
- AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
- AT91_SMC_EXNWMODE_DISABLE |
-#ifdef CONFIG_SYS_NAND_DBW_16
- AT91_SMC_DBW_16 |
-#else /* CONFIG_SYS_NAND_DBW_8 */
- AT91_SMC_DBW_8 |
-#endif
- AT91_SMC_TDF_(2));
+ writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[3].setup);
+
+ writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
+ AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
+ &smc->cs[3].pulse);
+
+ writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+ &smc->cs[3].cycle);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+ AT91_SMC_MODE_DBW_8 |
+ AT91_SMC_MODE_TDF_CYCLE(2),
+ &smc->cs[3].mode);
/* Configure RDY/BSY */
- at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+ at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
- at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+ at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
#endif /* CONFIG_CMD_NAND */
#ifdef CONFIG_MACB
static void meesc_macb_hw_init(void)
{
+ at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
/* Enable clock */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_EMAC);
+ writel(1 << AT91SAM9263_ID_EMAC, &pmc->pcer);
at91_macb_hw_init();
}
#endif
@@ -117,26 +117,27 @@ static void meesc_macb_hw_init(void)
*/
static void meesc_ethercat_hw_init(void)
{
+ at91_smc_t *smc1 = (at91_smc_t *) AT91_SMC1_BASE;
+
/* Configure SMC EBI1_CS0 for EtherCAT */
- at91_sys_write(AT91_SMC1_SETUP(0),
- AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC1_PULSE(0),
- AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(9) |
- AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(9));
- at91_sys_write(AT91_SMC1_CYCLE(0),
- AT91_SMC_NWECYCLE_(10) | AT91_SMC_NRDCYCLE_(5));
+ writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(0) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc1->cs[0].setup);
+ writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(9) |
+ AT91_SMC_PULSE_NRD(5) | AT91_SMC_PULSE_NCS_RD(9),
+ &smc1->cs[0].pulse);
+ writel(AT91_SMC_CYCLE_NWE(10) | AT91_SMC_CYCLE_NRD(6),
+ &smc1->cs[0].cycle);
/*
* Configure behavior at external wait signal, byte-select mode, 16 bit
* data bus width, none data float wait states and TDF optimization
*/
- at91_sys_write(AT91_SMC1_MODE(0),
- AT91_SMC_READMODE | AT91_SMC_EXNWMODE_READY |
- AT91_SMC_BAT_SELECT | AT91_SMC_DBW_16 | AT91_SMC_TDF_(0) |
- AT91_SMC_TDFMODE);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_EXNW_READY |
+ AT91_SMC_MODE_DBW_16 | AT91_SMC_MODE_TDF_CYCLE(0) |
+ AT91_SMC_MODE_TDF, &smc1->cs[0].mode);
/* Configure RDY/BSY */
- at91_set_B_periph(AT91_PIN_PE20, 0); /* EBI1_NWAIT */
+ at91_set_b_periph(AT91_PIO_PORTE, 20, 0); /* EBI1_NWAIT */
}
int dram_init(void)
@@ -150,7 +151,7 @@ int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)AT91SAM9263_BASE_EMAC, 0x00);
+ rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x00);
#endif
return rc;
}
@@ -175,7 +176,7 @@ int checkboard(void)
gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
puts("Board: EtherCAN/2 Gateway");
/* switch on LED1D */
- at91_set_gpio_output(AT91_PIN_PB12, 1);
+ at91_set_pio_output(AT91_PIO_PORTB, 12, 1);
break;
default:
/* assume, no ET1100 present, arch number of EtherCAN/2-Board */
@@ -222,8 +223,9 @@ u32 get_board_rev(void)
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
- char *str;
- char buf[32];
+ char *str;
+ char buf[32];
+ at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
/*
* Normally the processor clock has a divisor of 2.
@@ -231,10 +233,9 @@ int misc_init_r(void)
* Check the user has set environment mdiv to 4 to change the divisor.
*/
if ((str = getenv("mdiv")) && (strcmp(str, "4") == 0)) {
- at91_sys_write(AT91_PMC_MCKR,
- (at91_sys_read(AT91_PMC_MCKR) & ~AT91_PMC_MDIV) |
- AT91SAM9_PMC_MDIV_4);
- at91_clock_init(0);
+ writel((readl(&pmc->mckr) & ~AT91_PMC_MDIV) |
+ AT91SAM9_PMC_MDIV_4, &pmc->mckr);
+ at91_clock_init(CONFIG_SYS_AT91_MAIN_CLOCK);
serial_setbrg();
/* Notify the user that the clock is not default */
printf("Setting master clock to %s MHz\n",
@@ -247,10 +248,14 @@ int misc_init_r(void)
int board_init(void)
{
+ at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
+
/* Peripheral Clock Enable Register */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_PIOA |
- 1 << AT91SAM9263_ID_PIOB |
- 1 << AT91SAM9263_ID_PIOCDE);
+ writel(1 << AT91SAM9263_ID_PIOA |
+ 1 << AT91SAM9263_ID_PIOB |
+ 1 << AT91SAM9263_ID_PIOCDE |
+ 1 << AT91SAM9263_ID_UHP,
+ &pmc->pcer);
/* initialize ET1100 Controller */
meesc_ethercat_hw_init();
@@ -271,5 +276,8 @@ int board_init(void)
#ifdef CONFIG_AT91_CAN
at91_can_hw_init();
#endif
+#ifdef CONFIG_USB_OHCI_NEW
+ at91_uhp_hw_init();
+#endif
return 0;
}
diff --git a/board/eukrea/cpuat91/cpuat91.c b/board/eukrea/cpuat91/cpuat91.c
index 0017962..cd4d42c 100644
--- a/board/eukrea/cpuat91/cpuat91.c
+++ b/board/eukrea/cpuat91/cpuat91.c
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2006 Eukrea Electromatique <www.eukrea.com>
+ * (C) Copyright 2006-2010 Eukrea Electromatique <www.eukrea.com>
* Eric Benard <eric@eukrea.com>
* based on at91rm9200dk.c which is :
* (C) Copyright 2002
@@ -27,13 +27,11 @@
#include <common.h>
#include <netdev.h>
-#include <asm/arch/AT91RM9200.h>
-#include <asm/io.h>
-#if defined(CONFIG_DRIVER_ETHER)
-#include <at91rm9200_net.h>
-#include <ks8721.h>
-#endif
+#include <asm/io.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/at91_pio.h>
+#include <asm/arch/at91_pmc.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -61,31 +59,7 @@ int dram_init(void)
return 0;
}
-#if defined(CONFIG_DRIVER_ETHER)
-#if defined(CONFIG_CMD_NET)
-
-/*
- * Name:
- * at91rm9200_GetPhyInterface
- * Description:
- * Initialise the interface functions to the PHY
- * Arguments:
- * None
- * Return value:
- * None
- */
-void at91rm9200_GetPhyInterface(AT91PS_PhyOps p_phyops)
-{
- p_phyops->Init = ks8721_initphy;
- p_phyops->IsPhyConnected = ks8721_isphyconnected;
- p_phyops->GetLinkSpeed = ks8721_getlinkspeed;
- p_phyops->AutoNegotiate = ks8721_autonegotiate;
-}
-
-#endif /* CONFIG_CMD_NET */
-#endif /* CONFIG_DRIVER_ETHER */
#ifdef CONFIG_DRIVER_AT91EMAC
-
int board_eth_init(bd_t *bis)
{
int rc = 0;
@@ -93,3 +67,20 @@ int board_eth_init(bd_t *bis)
return rc;
}
#endif
+
+#ifdef CONFIG_SOFT_I2C
+void i2c_init_board(void)
+{
+ u32 pin;
+ at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
+ at91_pio_t *pio = (at91_pio_t *) AT91_PIO_BASE;
+
+ writel(1 << AT91_ID_PIOA, &pmc->pcer);
+ pin = AT91_PMX_AA_TWD | AT91_PMX_AA_TWCK;
+ writel(pin, &pio->pioa.idr);
+ writel(pin, &pio->pioa.pudr);
+ writel(pin, &pio->pioa.per);
+ writel(pin, &pio->pioa.oer);
+ writel(pin, &pio->pioa.sodr);
+}
+#endif