Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master'

20 files changed, 0 insertions, 1315 deletions

diff --git a/board/actux1/Makefile b/board/actux1/Makefile
deleted file mode 100644
index 05a8669..0000000
--- a/board/actux1/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= actux1.o
diff --git a/board/actux1/actux1.c b/board/actux1/actux1.c
deleted file mode 100644
index 03ccd93..0000000
--- a/board/actux1/actux1.c
+++ /dev/null
@@ -1,148 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#ifdef CONFIG_PCI
-#include <pci.h>
-#include <asm/arch/ixp425pci.h>
-#endif
-
-#include "actux1_hw.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/* CS5: Debug port */
-	writel(0x9d520003, IXP425_EXP_CS5);
-	/* CS6: HwRel */
-	writel(0x81860001, IXP425_EXP_CS6);
-	/* CS7: LEDs */
-	writel(0x80900003, IXP425_EXP_CS7);
-	return 0;
-}
-
-int board_init(void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x00000100;
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
-
-	/* Setup GPIOs for PCI INTA */
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI1_INTA);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI1_INTA);
-
-	/* Setup GPIOs for 33MHz clock output */
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
-	writel(0x011001FF, IXP425_GPIO_GPCLKR);
-
-	udelay(533);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
-
-	ACTUX1_LED1(2);
-	ACTUX1_LED2(2);
-	ACTUX1_LED3(0);
-	ACTUX1_LED4(0);
-	ACTUX1_LED5(0);
-	ACTUX1_LED6(0);
-	ACTUX1_LED7(0);
-
-	ACTUX1_HS(ACTUX1_HS_DCD);
-
-	return 0;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-
-	puts("Board: AcTux-1 rev.");
-	putc(ACTUX1_BOARDREL + 'A' - 1);
-
-	if (i > 0) {
-		puts(", serial# ");
-		puts(buf);
-	}
-	putc('\n');
-
-	return 0;
-}
-
-/*************************************************************************
- * get_board_rev() - setup to pass kernel board revision information
- * 0 = reserved
- * 1 = Rev. A
- * 2 = Rev. B
- *************************************************************************/
-u32 get_board_rev(void)
-{
-	return ACTUX1_BOARDREL;
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
-	return 0;
-}
-
-
-#ifdef CONFIG_PCI
-struct pci_controller hose;
-
-void pci_init_board(void)
-{
-	pci_ixp_init(&hose);
-}
-#endif
-
-void reset_phy(void)
-{
-	u16 id1, id2;
-
-	/* initialize the PHY */
-	miiphy_reset("NPE0", CONFIG_PHY_ADDR);
-
-	miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1);
-	miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2);
-
-	id2 &= 0xFFF0;		/* mask out revision bits */
-
-	if (id1 == 0x13 && id2 == 0x78e0) {
-		/*
-		 * LXT971/LXT972 PHY: set LED outputs:
-		 * LED1(green) = Link/ACT,
-		 * LED2 (unused) = LINK,
-		 * LED3(red) = Coll
-		 */
-		miiphy_write("NPE0", CONFIG_PHY_ADDR, 20, 0xD432);
-	} else if (id1 == 0x143 && id2 == 0xbc30) {
-		/* BCM5241: default values are OK */
-	} else
-		printf("unknown ethernet PHY ID: %x %x\n", id1, id2);
-}
diff --git a/board/actux1/actux1_hw.h b/board/actux1/actux1_hw.h
deleted file mode 100644
index 5627f24..0000000
--- a/board/actux1/actux1_hw.h
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * hardware register definitions for the AcTux-1 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _ACTUX1_HW_H
-#define _ACTUX1_HW_H
-
-/* 0 = LED off,1 = green, 2 = red, 3 = orange */
-#define ACTUX1_LED1(a)	writeb((a),   IXP425_EXP_BUS_CS7_BASE_PHYS + 0)
-#define ACTUX1_LED2(a)	writeb((a),   IXP425_EXP_BUS_CS7_BASE_PHYS + 1)
-#define ACTUX1_LED3(a)	writeb((a),   IXP425_EXP_BUS_CS7_BASE_PHYS + 2)
-#define ACTUX1_LED4(a)	writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 3)
-#define ACTUX1_LED5(a)	writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 4)
-#define ACTUX1_LED6(a)	writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 5)
-#define ACTUX1_LED7(a)	writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 6)
-#define ACTUX1_HS(a)	writeb((a),   IXP425_EXP_BUS_CS7_BASE_PHYS + 7)
-#define ACTUX1_HS_DCD	0x01
-#define ACTUX1_HS_DSR	0x02
-
-#define ACTUX1_DBG_PORT	IXP425_EXP_BUS_CS5_BASE_PHYS
-#define ACTUX1_BOARDREL	(readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F)
-
-/* GPIO settings */
-#define CONFIG_SYS_GPIO_PCI1_INTA		2
-#define CONFIG_SYS_GPIO_PCI2_INTA		3
-#define CONFIG_SYS_GPIO_I2C_SDA		4
-#define CONFIG_SYS_GPIO_I2C_SCL		5
-#define CONFIG_SYS_GPIO_DBGJUMPER		9
-#define CONFIG_SYS_GPIO_BUTTON1		10
-#define CONFIG_SYS_GPIO_DBGSENSE		11
-#define CONFIG_SYS_GPIO_DTR			12
-#define CONFIG_SYS_GPIO_IORST			13	/* Out */
-#define CONFIG_SYS_GPIO_PCI_CLK		14	/* Out */
-#define CONFIG_SYS_GPIO_EXTBUS_CLK		15	/* Out */
-
-#endif
diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds
deleted file mode 100644
index 4716e4f..0000000
--- a/board/actux1/u-boot.lds
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm")
-OUTPUT_ARCH (arm)
-ENTRY (_start)
-SECTIONS
-{
-	. = 0x00000000;
-
-	. = ALIGN (4);
-	.text : {
-		*(.__image_copy_start)
-		arch/arm/cpu/ixp/start.o(.text*)
-		net/built-in.o(.text*)
-		board/actux1/built-in.o(.text*)
-		arch/arm/cpu/ixp/built-in.o(.text*)
-		drivers/input/built-in.o(.text*)
-
-		. = env_offset;
-		common/env_embedded.o(.ppcenv)
-		*(.text*)
-	}
-
-	. = ALIGN(4);
-	.rodata : {
-		*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-	}
-	. = ALIGN(4);
-	.data : {
-		*(.data*)
-	}
-	. = ALIGN(4);
-	.got : {
-		*(.got)
-	}
-	. =.;
-
-	. = ALIGN(4);
-	.u_boot_list : {
-		KEEP(*(SORT(.u_boot_list*)));
-	}
-
-	. = ALIGN (4);
-
-	.image_copy_end :
-	{
-		*(.__image_copy_end)
-	}
-
-	.rel_dyn_start :
-	{
-		*(.__rel_dyn_start)
-	}
-
-	.rel.dyn : {
-		*(.rel*)
-	}
-
-	.rel_dyn_end :
-	{
-		*(.__rel_dyn_end)
-	}
-
-	_end = .;
-
-/*
- * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
- * __bss_base and __bss_limit are for linker only (overlay ordering)
- */
-
-	.bss_start __rel_dyn_start (OVERLAY) : {
-		KEEP(*(.__bss_start));
-		__bss_base = .;
-	}
-
-	.bss __bss_base (OVERLAY) : {
-		*(.bss*)
-		 . = ALIGN(4);
-		 __bss_limit = .;
-	}
-	.bss_end __bss_limit (OVERLAY) : {
-		KEEP(*(.__bss_end));
-	}
-
-	.dynsym _end : { *(.dynsym) }
-	.dynbss : { *(.dynbss) }
-	.dynstr : { *(.dynstr*) }
-	.dynamic : { *(.dynamic*) }
-	.hash : { *(.hash*) }
-	.plt : { *(.plt*) }
-	.interp : { *(.interp*) }
-	.gnu : { *(.gnu*) }
-	.ARM.exidx : { *(.ARM.exidx*) }
-}
diff --git a/board/actux2/Makefile b/board/actux2/Makefile
deleted file mode 100644
index 24cbff1..0000000
--- a/board/actux2/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= actux2.o
diff --git a/board/actux2/actux2.c b/board/actux2/actux2.c
deleted file mode 100644
index e578cd0..0000000
--- a/board/actux2/actux2.c
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-#include <asm/io.h>
-
-#include <miiphy.h>
-
-#include "actux2_hw.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/* CS1: IPAC-X */
-	writel(0x94d10013, IXP425_EXP_CS1);
-	/* CS5: Debug port */
-	writel(0x9d520003, IXP425_EXP_CS5);
-	/* CS6: HW release register */
-	writel(0x81860001, IXP425_EXP_CS6);
-	/* CS7: LEDs */
-	writel(0x80900003, IXP425_EXP_CS7);
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x00000100;
-
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD);
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST);
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD);
-
-	/* Setup GPIOs for Interrupt inputs */
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT);
-
-	/* Setup GPIOs for 33MHz clock output */
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
-	writel(0x011001FF, IXP425_GPIO_GPCLKR);
-
-	udelay(533);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST);
-
-	ACTUX2_LED1(1);
-	ACTUX2_LED2(0);
-	ACTUX2_LED3(0);
-	ACTUX2_LED4(0);
-
-	return 0;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-
-	puts("Board: AcTux-2 rev.");
-	putc(ACTUX2_BOARDREL + 'A' - 1);
-
-	if (i > 0) {
-		puts(", serial# ");
-		puts(buf);
-	}
-	putc('\n');
-
-	return 0;
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
-	return 0;
-}
-
-/*************************************************************************
- * get_board_rev() - setup to pass kernel board revision information
- * 0 = reserved
- * 1 = Rev. A
- * 2 = Rev. B
- *************************************************************************/
-u32 get_board_rev(void)
-{
-	return ACTUX2_BOARDREL;
-}
-
-void reset_phy(void)
-{
-	/* init IcPlus IP175C ethernet switch to native IP175C mode */
-	miiphy_write("NPE0", 29, 31, 0x175C);
-}
diff --git a/board/actux2/actux2_hw.h b/board/actux2/actux2_hw.h
deleted file mode 100644
index 57c6fa7..0000000
--- a/board/actux2/actux2_hw.h
+++ /dev/null
@@ -1,43 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * hardware register definitions for the AcTux-2 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _ACTUX2_HW_H
-#define _ACTUX2_HW_H
-
-/* 0 = LED off,1 = green, 2 = red, 3 = orange */
-#define ACTUX2_LED1(a)	writeb((a ? 2 : 0), IXP425_EXP_BUS_CS7_BASE_PHYS + 0)
-#define ACTUX2_LED2(a)	writeb((a ? 2 : 0), IXP425_EXP_BUS_CS7_BASE_PHYS + 1)
-#define ACTUX2_LED3(a)	writeb((a ? 0 : 2), IXP425_EXP_BUS_CS7_BASE_PHYS + 2)
-#define ACTUX2_LED4(a)	writeb((a ? 0 : 2), IXP425_EXP_BUS_CS7_BASE_PHYS + 3)
-
-#define ACTUX2_DBG_PORT	IXP425_EXP_BUS_CS5_BASE_PHYS
-#define ACTUX2_BOARDREL	(readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F)
-#define ACTUX2_OPTION	(readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0xF0)
-
-/*
- * GPIO settings
- */
-#define CONFIG_SYS_GPIO_DBGINT			0
-#define CONFIG_SYS_GPIO_ETHINT			1
-#define CONFIG_SYS_GPIO_ETHRST			2	/* Out */
-#define CONFIG_SYS_GPIO_LED5_GN		3	/* Out */
-#define CONFIG_SYS_GPIO_UNUSED4		4
-#define CONFIG_SYS_GPIO_UNUSED5		5
-#define CONFIG_SYS_GPIO_DSR			6	/* Out */
-#define CONFIG_SYS_GPIO_DCD			7	/* Out */
-#define CONFIG_SYS_GPIO_IPAC_INT		8
-#define CONFIG_SYS_GPIO_DBGJUMPER		9
-#define CONFIG_SYS_GPIO_BUTTON1		10
-#define CONFIG_SYS_GPIO_DBGSENSE		11
-#define CONFIG_SYS_GPIO_DTR			12
-#define CONFIG_SYS_GPIO_IORST			13	/* Out */
-#define CONFIG_SYS_GPIO_PCI_CLK		14	/* Out */
-#define CONFIG_SYS_GPIO_EXTBUS_CLK		15	/* Out */
-
-#endif
diff --git a/board/actux2/u-boot.lds b/board/actux2/u-boot.lds
deleted file mode 100644
index f00d7c7..0000000
--- a/board/actux2/u-boot.lds
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm")
-OUTPUT_ARCH (arm)
-ENTRY (_start)
-SECTIONS
-{
-	. = 0x00000000;
-
-	. = ALIGN (4);
-	.text : {
-		*(.__image_copy_start)
-		arch/arm/cpu/ixp/start.o(.text*)
-		net/built-in.o(.text*)
-		board/actux2/built-in.o(.text*)
-		arch/arm/cpu/ixp/built-in.o(.text*)
-		drivers/input/built-in.o(.text*)
-
-		. = env_offset;
-		common/env_embedded.o(.ppcenv)
-		*(.text*)
-	}
-
-	. = ALIGN(4);
-	.rodata : {
-		*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-	}
-	. = ALIGN(4);
-	.data : {
-		*(.data*)
-	}
-	. = ALIGN(4);
-	.got : {
-		*(.got)
-	}
-	. =.;
-
-	. = ALIGN(4);
-	.u_boot_list : {
-		KEEP(*(SORT(.u_boot_list*)));
-	}
-
-	. = ALIGN (4);
-
-	.image_copy_end :
-	{
-		*(.__image_copy_end)
-	}
-
-	.rel_dyn_start :
-	{
-		*(.__rel_dyn_start)
-	}
-
-	.rel.dyn : {
-		*(.rel*)
-	}
-
-	.rel_dyn_end :
-	{
-		*(.__rel_dyn_end)
-	}
-
-	_end = .;
-
-/*
- * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
- * __bss_base and __bss_limit are for linker only (overlay ordering)
- */
-
-	.bss_start __rel_dyn_start (OVERLAY) : {
-		KEEP(*(.__bss_start));
-		__bss_base = .;
-	}
-
-	.bss __bss_base (OVERLAY) : {
-		*(.bss*)
-		 . = ALIGN(4);
-		 __bss_limit = .;
-	}
-	.bss_end __bss_limit (OVERLAY) : {
-		KEEP(*(.__bss_end));
-	}
-
-	.dynsym _end : { *(.dynsym) }
-	.dynbss : { *(.dynbss) }
-	.dynstr : { *(.dynstr*) }
-	.dynamic : { *(.dynamic*) }
-	.hash : { *(.hash*) }
-	.plt : { *(.plt*) }
-	.interp : { *(.interp*) }
-	.gnu : { *(.gnu*) }
-	.ARM.exidx : { *(.ARM.exidx*) }
-}
diff --git a/board/actux3/Makefile b/board/actux3/Makefile
deleted file mode 100644
index f628f26..0000000
--- a/board/actux3/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= actux3.o
diff --git a/board/actux3/actux3.c b/board/actux3/actux3.c
deleted file mode 100644
index 09c803c..0000000
--- a/board/actux3/actux3.c
+++ /dev/null
@@ -1,149 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#include "actux3_hw.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/* CS1: IPAC-X */
-	writel(0x94d10013, IXP425_EXP_CS1);
-	/* CS5: Debug port */
-	writel(0x9d520003, IXP425_EXP_CS5);
-	/* CS6: Release/Option register */
-	writel(0x81860001, IXP425_EXP_CS6);
-	/* CS7: LEDs */
-	writel(0x80900003, IXP425_EXP_CS7);
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x00000100;
-
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED5_GN);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_RT);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_GN);
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST);
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD);
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED5_GN);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_RT);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_GN);
-
-	/*
-	 * Setup GPIO's for Interrupt inputs
-	 */
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT);
-
-	/*
-	 * Setup GPIO's for 33MHz clock output
-	 */
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
-	writel(0x011001FF, IXP425_GPIO_GPCLKR);
-
-	/* we need a minimum PCI reset pulse width after enabling the clock */
-	udelay(533);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST);
-
-	ACTUX3_LED1_RT(1);
-	ACTUX3_LED1_GN(0);
-	ACTUX3_LED2_RT(0);
-	ACTUX3_LED2_GN(0);
-	ACTUX3_LED3_RT(0);
-	ACTUX3_LED3_GN(0);
-	ACTUX3_LED4_GN(0);
-	ACTUX3_LED5_RT(0);
-
-	return 0;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-
-	puts("Board: AcTux-3 rev.");
-	putc(ACTUX3_BOARDREL + 'A' - 1);
-
-	if (i > 0) {
-		puts (", serial# ");
-		puts (buf);
-	}
-	putc('\n');
-
-	return 0;
-}
-
-/*************************************************************************
- * get_board_rev() - setup to pass kernel board revision information
- * 0 = reserved
- * 1 = Rev. A
- * 2 = Rev. B
- *************************************************************************/
-u32 get_board_rev(void)
-{
-	return ACTUX3_BOARDREL;
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
-	return 0;
-}
-
-void reset_phy(void)
-{
-	int i;
-
-	/* initialize the PHY */
-	miiphy_reset("NPE0", CONFIG_PHY_ADDR);
-
-	/* all LED outputs = Link/Act */
-	miiphy_write("NPE0", CONFIG_PHY_ADDR, 0x16, 0x0AAA);
-
-	/*
-	 * The Marvell 88E6060 switch comes up with all ports disabled.
-	 * set all ethernet switch ports to forwarding state
-	*/
-	for (i = 1; i <= 5; i++)
-		miiphy_write("NPE0", CONFIG_PHY_ADDR + 8 + i, 0x04, 0x03);
-
-}
diff --git a/board/actux3/actux3_hw.h b/board/actux3/actux3_hw.h
deleted file mode 100644
index f8acb4d..0000000
--- a/board/actux3/actux3_hw.h
+++ /dev/null
@@ -1,44 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * hardware register definitions for the AcTux-3 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _ACTUX3_HW_H
-#define _ACTUX3_HW_H
-
-/* 0 = LED off,1 = ON */
-#define ACTUX3_LED1_RT(a)	writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 0)
-#define ACTUX3_LED1_GN(a)	writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 1)
-#define ACTUX3_LED2_RT(a)	writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 2)
-#define ACTUX3_LED2_GN(a)	writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 3)
-#define ACTUX3_LED3_RT(a)	writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 4)
-#define ACTUX3_LED3_GN(a)	writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 5)
-#define ACTUX3_LED4_GN(a)	writeb((a)^1, IXP425_EXP_BUS_CS7_BASE_PHYS + 6)
-#define ACTUX3_LED5_RT(a)	writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 7)
-
-#define ACTUX3_DBG_PORT		IXP425_EXP_BUS_CS5_BASE_PHYS
-#define ACTUX3_BOARDREL		(readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F)
-#define ACTUX3_OPTION		(readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0xF0)
-
-/* GPIO settings */
-#define CONFIG_SYS_GPIO_DBGINT			0
-#define CONFIG_SYS_GPIO_ETHINT			1
-#define CONFIG_SYS_GPIO_ETHRST			2	/* Out */
-#define CONFIG_SYS_GPIO_LED5_GN		3	/* Out */
-#define CONFIG_SYS_GPIO_LED6_RT		4	/* Out */
-#define CONFIG_SYS_GPIO_LED6_GN		5	/* Out */
-#define CONFIG_SYS_GPIO_DSR			6	/* Out */
-#define CONFIG_SYS_GPIO_DCD			7	/* Out */
-#define CONFIG_SYS_GPIO_DBGJUMPER		9
-#define CONFIG_SYS_GPIO_BUTTON1		10
-#define CONFIG_SYS_GPIO_DBGSENSE		11
-#define CONFIG_SYS_GPIO_DTR			12
-#define CONFIG_SYS_GPIO_IORST			13	/* Out */
-#define CONFIG_SYS_GPIO_PCI_CLK		14	/* Out */
-#define CONFIG_SYS_GPIO_EXTBUS_CLK		15	/* Out */
-
-#endif
diff --git a/board/actux3/u-boot.lds b/board/actux3/u-boot.lds
deleted file mode 100644
index 2de3ca6..0000000
--- a/board/actux3/u-boot.lds
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm")
-OUTPUT_ARCH (arm)
-ENTRY (_start)
-SECTIONS
-{
-	. = 0x00000000;
-
-	. = ALIGN (4);
-	.text : {
-		*(.__image_copy_start)
-		arch/arm/cpu/ixp/start.o(.text*)
-		net/built-in.o(.text*)
-		board/actux3/built-in.o(.text*)
-		arch/arm/cpu/ixp/built-in.o(.text*)
-		drivers/input/built-in.o(.text*)
-
-		. = env_offset;
-		common/env_embedded.o(.ppcenv)
-		*(.text*)
-	}
-
-	. = ALIGN(4);
-	.rodata : {
-		*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-	}
-	. = ALIGN(4);
-	.data : {
-		*(.data*)
-	}
-	. = ALIGN(4);
-	.got : {
-		*(.got)
-	}
-	. =.;
-
-	. = ALIGN(4);
-	.u_boot_list : {
-		KEEP(*(SORT(.u_boot_list*)));
-	}
-
-	. = ALIGN (4);
-
-	.image_copy_end :
-	{
-		*(.__image_copy_end)
-	}
-
-	.rel_dyn_start :
-	{
-		*(.__rel_dyn_start)
-	}
-
-	.rel.dyn : {
-		*(.rel*)
-	}
-
-	.rel_dyn_end :
-	{
-		*(.__rel_dyn_end)
-	}
-
-	_end = .;
-
-/*
- * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
- * __bss_base and __bss_limit are for linker only (overlay ordering)
- */
-
-	.bss_start __rel_dyn_start (OVERLAY) : {
-		KEEP(*(.__bss_start));
-		__bss_base = .;
-	}
-
-	.bss __bss_base (OVERLAY) : {
-		*(.bss*)
-		 . = ALIGN(4);
-		__bss_limit = .;
-	}
-	.bss_end __bss_limit (OVERLAY) : {
-		KEEP(*(.__bss_end));
-	}
-
-	.dynsym _end : { *(.dynsym) }
-	.dynbss : { *(.dynbss) }
-	.dynstr : { *(.dynstr*) }
-	.dynamic : { *(.dynamic*) }
-	.hash : { *(.hash*) }
-	.plt : { *(.plt*) }
-	.interp : { *(.interp*) }
-	.gnu : { *(.gnu*) }
-	.ARM.exidx : { *(.ARM.exidx*) }
-}
diff --git a/board/actux4/Makefile b/board/actux4/Makefile
deleted file mode 100644
index b949b60..0000000
--- a/board/actux4/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= actux4.o
diff --git a/board/actux4/actux4.c b/board/actux4/actux4.c
deleted file mode 100644
index 81c5458..0000000
--- a/board/actux4/actux4.c
+++ /dev/null
@@ -1,129 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#ifdef CONFIG_PCI
-#include <pci.h>
-#include <asm/arch/ixp425pci.h>
-#endif
-
-#include "actux4_hw.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	writel(0xbd113c42, IXP425_EXP_CS1);
-	return 0;
-}
-
-int board_init(void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x00000100;
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_nPWRON);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_nPWRON);
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
-
-	/* led not populated on board*/
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED3);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED3);
-
-	/* middle LED */
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED2);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED2);
-
-	/* right LED */
-	/* weak pulldown = LED weak on */
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_LED1);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED1);
-
-	/* Setup GPIO's for Interrupt inputs */
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTA);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTB);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTC);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RTCINT);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB);
-
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTA);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTB);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTC);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RTCINT);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB);
-
-	/* Setup GPIO's for 33MHz clock output */
-	writel(0x011001FF, IXP425_GPIO_GPCLKR);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
-
-	udelay(10000);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
-	udelay(10000);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
-	udelay(10000);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
-
-	return 0;
-}
-
-/* Check Board Identity */
-int checkboard(void)
-{
-	puts("Board: AcTux-4\n");
-	return 0;
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
-	return 0;
-}
-
-#ifdef CONFIG_PCI
-struct pci_controller hose;
-
-void pci_init_board(void)
-{
-	pci_ixp_init(&hose);
-}
-#endif
-
-/*
- * Hardcoded flash setup:
- * Flash 0 is a non-CFI SST 39VF020 flash, 8 bit flash / 8 bit bus.
- * Flash 1 is an Intel *16 flash using the CFI driver.
- */
-ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
-{
-	if (banknum == 0) {	/* non-CFI boot flash */
-		info->portwidth = 1;
-		info->chipwidth = 1;
-		info->interface = FLASH_CFI_X8;
-		return 1;
-	} else
-		return 0;
-}
diff --git a/board/actux4/actux4_hw.h b/board/actux4/actux4_hw.h
deleted file mode 100644
index b936376..0000000
--- a/board/actux4/actux4_hw.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * hardware register definitions for the AcTux-4 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _ACTUX4_HW_H
-#define _ACTUX4_HW_H
-
-/*
- * GPIO settings
- */
-#define CONFIG_SYS_GPIO_USBINTA		0
-#define CONFIG_SYS_GPIO_USBINTB		1
-#define CONFIG_SYS_GPIO_USBINTC		2
-#define CONFIG_SYS_GPIO_nPWRON			3	/* Out */
-#define CONFIG_SYS_GPIO_I2C_SCL		4
-#define CONFIG_SYS_GPIO_I2C_SDA		5
-#define CONFIG_SYS_GPIO_PCI_INTB		6
-#define CONFIG_SYS_GPIO_BUTTON1		7
-#define CONFIG_SYS_GPIO_LED1			8	/* Out */
-#define CONFIG_SYS_GPIO_RTCINT			9
-#define CONFIG_SYS_GPIO_LED2			10	/* Out */
-#define CONFIG_SYS_GPIO_PCI_INTA		11
-#define CONFIG_SYS_GPIO_IORST			12	/* Out */
-#define CONFIG_SYS_GPIO_LED3			13	/* Out */
-#define CONFIG_SYS_GPIO_PCI_CLK		14	/* Out */
-#define CONFIG_SYS_GPIO_EXTBUS_CLK		15	/* Out */
-
-#endif
diff --git a/board/dvlhost/Makefile b/board/dvlhost/Makefile
deleted file mode 100644
index 8b48936..0000000
--- a/board/dvlhost/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= dvlhost.o watchdog.o
diff --git a/board/dvlhost/dvlhost.c b/board/dvlhost/dvlhost.c
deleted file mode 100644
index 087070f..0000000
--- a/board/dvlhost/dvlhost.c
+++ /dev/null
@@ -1,112 +0,0 @@
-/*
- * (C) Copyright 2009
- * Michael Schwingen, michael@schwingen.org
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <config.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#ifdef CONFIG_PCI
-#include <pci.h>
-#include <asm/arch/ixp425pci.h>
-#endif
-
-#include "dvlhost_hw.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/* CS1: LED Latch */
-	writel(0xBFFF0002, IXP425_EXP_CS1);
-	return 0;
-}
-
-int board_init(void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x00000100;
-
-	/* Setup GPIOs used as output */
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_WDGTRIGGER);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DLAN_PAIRING);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PCIRST);
-
-	/*
-	 * LED latch enable and watchdog enable are tied to the same GPIO,
-	 * so we need to trigger the watchdog if we want to enable the LEDs.
-	*/
-#ifdef CONFIG_HW_WATCHDOG
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_WDG_LED_EN);
-#else
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_WDG_LED_EN);
-#endif
-
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_WDGTRIGGER);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DLAN_PAIRING);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_WDG_LED_EN);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCIRST);
-
-	/* Setup GPIOs for Interrupt inputs */
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_WLAN);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_PAIRING);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_RESET);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_IRQA);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_IRQB);
-
-	/* Setup GPIO's for 33MHz clock output */
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
-	writel(0x01FF01FF, IXP425_GPIO_GPCLKR);
-
-	/* turn off all LEDs */
-	writew(0x0000, DVLHOST_LED_LATCH);
-
-	udelay(533);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_PCIRST);
-
-	return 0;
-}
-
-/* Check Board Identity */
-int checkboard(void)
-{
-	char *s = getenv("serial#");
-
-	puts("Board: dLAN 200AV (dvlhost)");
-
-	if (s != NULL) {
-		puts(", serial# ");
-		puts(s);
-	}
-	putc('\n');
-
-	return 0;
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
-	return 0;
-}
-
-#ifdef CONFIG_PCI
-struct pci_controller hose;
-
-void pci_init_board(void)
-{
-	pci_ixp_init(&hose);
-}
-#endif
-
-void reset_phy(void)
-{
-	/* init IcPlus IP175C ethernet switch to native IP175C mode */
-	miiphy_write("NPE1", 29, 31, 0x175C);
-}
diff --git a/board/dvlhost/dvlhost_hw.h b/board/dvlhost/dvlhost_hw.h
deleted file mode 100644
index 545099e..0000000
--- a/board/dvlhost/dvlhost_hw.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/*
- * (C) Copyright 2009
- * Michael Schwingen, michael@schwingen.org
- *
- * hardware register definitions for the
- * dLAN200 AV Wireless G ("dvlhost") board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _DVLHOST_HW_H
-#define _DVLHOST_HW_H
-
-/*
- * GPIO settings
- */
-#define CONFIG_SYS_GPIO_WDGTRIGGER	0 /* Out */
-#define CONFIG_SYS_GPIO_BTN_WLAN	1
-#define CONFIG_SYS_GPIO_BTN_PAIRING	6
-#define CONFIG_SYS_GPIO_DLAN_PAIRING	7 /* Out */
-#define CONFIG_SYS_GPIO_BTN_RESET	9
-#define CONFIG_SYS_GPIO_IRQB		10
-#define CONFIG_SYS_GPIO_IRQA		11
-#define CONFIG_SYS_GPIO_WDG_LED_EN	12 /* Out */
-#define CONFIG_SYS_GPIO_PCIRST		13 /* Out */
-#define CONFIG_SYS_GPIO_PCI_CLK		14 /* Out */
-#define CONFIG_SYS_GPIO_EXTBUS_CLK	15 /* Out */
-
-#define DVLHOST_LED_LATCH	IXP425_EXP_BUS_CS1_BASE_PHYS
-
-#endif
diff --git a/board/dvlhost/u-boot.lds b/board/dvlhost/u-boot.lds
deleted file mode 100644
index ebcaf44..0000000
--- a/board/dvlhost/u-boot.lds
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm")
-OUTPUT_ARCH (arm)
-ENTRY (_start)
-SECTIONS
-{
-	. = 0x00000000;
-
-	. = ALIGN (4);
-	.text : {
-		*(.__image_copy_start)
-		arch/arm/cpu/ixp/start.o(.text*)
-		net/built-in.o(.text*)
-		board/dvlhost/built-in.o(.text*)
-		arch/arm/cpu/ixp/built-in.o(.text*)
-		drivers/serial/built-in.o(.text*)
-
-		. = env_offset;
-		common/env_embedded.o(.ppcenv)
-		*(.text*)
-	}
-
-	. = ALIGN (4);
-	.rodata : {
-		*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-	}
-	. = ALIGN (4);
-	.data : {
-		*(.data*)
-	}
-	. = ALIGN (4);
-	.got : {
-		*(.got)
-	}
-	. =.;
-
-	. = ALIGN(4);
-	.u_boot_list : {
-		KEEP(*(SORT(.u_boot_list*)));
-	}
-
-	. = ALIGN (4);
-
-	.image_copy_end :
-	{
-		*(.__image_copy_end)
-	}
-
-	.rel_dyn_start :
-	{
-		*(.__rel_dyn_start)
-	}
-
-	.rel.dyn : {
-		*(.rel*)
-	}
-
-	.rel_dyn_end :
-	{
-		*(.__rel_dyn_end)
-	}
-
-	_end = .;
-
-/*
- * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
- * __bss_base and __bss_limit are for linker only (overlay ordering)
- */
-
-	.bss_start __rel_dyn_start (OVERLAY) : {
-		KEEP(*(.__bss_start));
-		__bss_base = .;
-	}
-
-	.bss __bss_base (OVERLAY) : {
-		*(.bss*)
-		 . = ALIGN(4);
-		 __bss_limit = .;
-	}
-	.bss_end __bss_limit (OVERLAY) : {
-		KEEP(*(.__bss_end));
-	}
-
-	.dynsym _end : { *(.dynsym) }
-	.dynbss : { *(.dynbss) }
-	.dynstr : { *(.dynstr*) }
-	.dynamic : { *(.dynamic*) }
-	.hash : { *(.hash*) }
-	.plt : { *(.plt*) }
-	.interp : { *(.interp*) }
-	.gnu : { *(.gnu*) }
-	.ARM.exidx : { *(.ARM.exidx*) }
-}
diff --git a/board/dvlhost/watchdog.c b/board/dvlhost/watchdog.c
deleted file mode 100644
index 02ec35e..0000000
--- a/board/dvlhost/watchdog.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * (C) Copyright 2009
- * Michael Schwingen, michael@schwingen.org
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <config.h>
-#include <asm/io.h>
-#include "dvlhost_hw.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_HW_WATCHDOG
-#include <watchdog.h>
-#include <asm/arch/ixp425.h>
-
-void hw_watchdog_reset(void)
-{
-	unsigned int x;
-	x = readl(IXP425_GPIO_GPOUTR);
-	x ^= (1 << (CONFIG_SYS_GPIO_WDGTRIGGER));
-	writel(x, IXP425_GPIO_GPOUTR);
-}
-
-#endif /* CONFIG_HW_WATCHDOG */