Merge branch 'iu-boot/master' into 'u-boot-arm/master'

Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h

27 files changed, 936 insertions, 496 deletions

diff --git a/board/Barix/ipam390/ipam390-ais-uart.cfg b/board/Barix/ipam390/ipam390-ais-uart.cfg
index e1a99f2..709cf23 100644
--- a/board/Barix/ipam390/ipam390-ais-uart.cfg
+++ b/board/Barix/ipam390/ipam390-ais-uart.cfg
@@ -109,7 +109,7 @@ CLK2XSRC = 0x00000000
 ;NANDFCR = 0x00000000
 [EMIF25ASYNC]
 A1CR = 0x00000000
-A2CR = 0x3FFFFFFE
+A2CR = 0x04202110
 A3CR = 0x00000000
 A4CR = 0x00000000
 NANDFCR = 0x00000012
diff --git a/board/Barix/ipam390/ipam390.c b/board/Barix/ipam390/ipam390.c
index f3f276e..ae88b42 100644
--- a/board/Barix/ipam390/ipam390.c
+++ b/board/Barix/ipam390/ipam390.c
@@ -264,7 +264,7 @@ void show_boot_progress(int status)
 	static int green;
 
 	if (red == 0)
-		red = init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF);
+		red = init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
 	if (red != CONFIG_IPAM390_GPIO_LED_RED)
 		return;
 	if (green == 0)
@@ -277,10 +277,10 @@ void show_boot_progress(int status)
 	case BOOTSTAGE_ID_RUN_OS:
 		/*
 		 * set normal state
-		 * LED Red  : off
+		 * LED Red  : on
 		 * LED green: off
 		 */
-		gpio_set_value(red, LED_OFF);
+		gpio_set_value(red, LED_ON);
 		gpio_set_value(green, LED_OFF);
 		break;
 	case BOOTSTAGE_ID_MAIN_LOOP:
@@ -326,23 +326,12 @@ int spl_start_uboot(void)
 	if (!bootmode)
 		if (ret == 0)
 			bootmode = 1;
-	if (bootmode) {
-		/*
-		 * Booting U-Boot
-		 * LED Red  : on
-		 * LED green: off
-		 */
-		init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
-		init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
-	} else {
-		/*
-		 * Booting Linux
-		 * LED Red  : off
-		 * LED green: off
-		 */
-		init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF);
-		init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
-	}
+	/*
+	 * LED red  : on
+	 * LED green: off
+	 */
+	init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
+	init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
 	return bootmode;
 }
 #endif
diff --git a/board/atmel/at91sam9n12ek/at91sam9n12ek.c b/board/atmel/at91sam9n12ek/at91sam9n12ek.c
index 2ec32eb..9adc992 100644
--- a/board/atmel/at91sam9n12ek/at91sam9n12ek.c
+++ b/board/atmel/at91sam9n12ek/at91sam9n12ek.c
@@ -199,6 +199,13 @@ void at91sam9n12ek_ks8851_hw_init(void)
 }
 #endif
 
+#ifdef CONFIG_USB_ATMEL
+void at91sam9n12ek_usb_hw_init(void)
+{
+	at91_set_pio_output(AT91_PIO_PORTB, 7, 0);
+}
+#endif
+
 int board_early_init_f(void)
 {
 	/* Enable clocks for all PIOs */
@@ -230,6 +237,10 @@ int board_init(void)
 	at91sam9n12ek_ks8851_hw_init();
 #endif
 
+#ifdef CONFIG_USB_ATMEL
+	at91sam9n12ek_usb_hw_init();
+#endif
+
 	return 0;
 }
 
diff --git a/board/boundary/nitrogen6x/6x_upgrade.txt b/board/boundary/nitrogen6x/6x_upgrade.txt
index 1f9a889..1a62bbf 100644
--- a/board/boundary/nitrogen6x/6x_upgrade.txt
+++ b/board/boundary/nitrogen6x/6x_upgrade.txt
@@ -17,7 +17,7 @@ if ${fs}load ${dtype} ${disk}:1 12000000 u-boot.imx || ${fs}load ${dtype} ${disk
 			sleep 1 ;
 		   done
 		   echo "erasing" ;
-		   sf erase 0 0x50000 ;
+		   sf erase 0 0xC0000 ;
 		   # two steps to prevent bricking
 		   echo "programming" ;
 		   sf write 0x12000000 $offset $filesize ;
diff --git a/board/compulab/cm_t35/Makefile b/board/compulab/cm_t35/Makefile
index 66b264a..6e2e1cb 100644
--- a/board/compulab/cm_t35/Makefile
+++ b/board/compulab/cm_t35/Makefile
@@ -7,7 +7,4 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
-obj-$(CONFIG_DRIVER_OMAP34XX_I2C) += eeprom.o
-obj-$(CONFIG_LCD) += display.o
-
 obj-y	+= cm_t35.o leds.o
diff --git a/board/compulab/cm_t35/cm_t35.c b/board/compulab/cm_t35/cm_t35.c
index 19945c1..b9a9965 100644
--- a/board/compulab/cm_t35/cm_t35.c
+++ b/board/compulab/cm_t35/cm_t35.c
@@ -33,7 +33,7 @@
 #include <asm/ehci-omap.h>
 #include <asm/gpio.h>
 
-#include "eeprom.h"
+#include "../common/eeprom.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -160,7 +160,7 @@ static u32 cm_t3x_rev;
 u32 get_board_rev(void)
 {
 	if (!cm_t3x_rev)
-		cm_t3x_rev = cm_t3x_eeprom_get_board_rev();
+		cm_t3x_rev = cl_eeprom_get_board_rev();
 
 	return cm_t3x_rev;
 };
@@ -509,7 +509,7 @@ static int handle_mac_address(void)
 	if (rc)
 		return 0;
 
-	rc = cm_t3x_eeprom_read_mac_addr(enetaddr);
+	rc = cl_eeprom_read_mac_addr(enetaddr);
 	if (rc)
 		return rc;
 
@@ -599,5 +599,4 @@ int ehci_hcd_stop(void)
 {
 	return omap_ehci_hcd_stop();
 }
-
 #endif /* CONFIG_USB_EHCI_OMAP */
diff --git a/board/compulab/common/Makefile b/board/compulab/common/Makefile
new file mode 100644
index 0000000..831be2e
--- /dev/null
+++ b/board/compulab/common/Makefile
@@ -0,0 +1,10 @@
+#
+# (C) Copyright 2011 - 2013 CompuLab, Ltd. <www.compulab.co.il>
+#
+# Author: Igor Grinberg <grinberg@compulab.co.il>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-$(CONFIG_DRIVER_OMAP34XX_I2C) += eeprom.o
+obj-$(CONFIG_LCD) += omap3_display.o
diff --git a/board/compulab/cm_t35/eeprom.c b/board/compulab/common/eeprom.c
index df91acd..5aa3dbd 100644
--- a/board/compulab/cm_t35/eeprom.c
+++ b/board/compulab/common/eeprom.c
@@ -22,30 +22,30 @@
 #define LAYOUT_INVALID	0
 #define LAYOUT_LEGACY	0xff
 
-static int eeprom_layout; /* Implicitly LAYOUT_INVALID */
+static int cl_eeprom_layout; /* Implicitly LAYOUT_INVALID */
 
-static int cm_t3x_eeprom_read(uint offset, uchar *buf, int len)
+static int cl_eeprom_read(uint offset, uchar *buf, int len)
 {
 	return i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, offset,
 			CONFIG_SYS_I2C_EEPROM_ADDR_LEN, buf, len);
 }
 
-static int eeprom_setup_layout(void)
+static int cl_eeprom_setup_layout(void)
 {
 	int res;
 
-	if (eeprom_layout != LAYOUT_INVALID)
+	if (cl_eeprom_layout != LAYOUT_INVALID)
 		return 0;
 
-	res = cm_t3x_eeprom_read(EEPROM_LAYOUT_VER_OFFSET,
-						(uchar *)&eeprom_layout, 1);
+	res = cl_eeprom_read(EEPROM_LAYOUT_VER_OFFSET,
+			     (uchar *)&cl_eeprom_layout, 1);
 	if (res) {
-		eeprom_layout = LAYOUT_INVALID;
+		cl_eeprom_layout = LAYOUT_INVALID;
 		return res;
 	}
 
-	if (eeprom_layout == 0 || eeprom_layout >= 0x20)
-		eeprom_layout = LAYOUT_LEGACY;
+	if (cl_eeprom_layout == 0 || cl_eeprom_layout >= 0x20)
+		cl_eeprom_layout = LAYOUT_LEGACY;
 
 	return 0;
 }
@@ -56,12 +56,14 @@ void get_board_serial(struct tag_serialnr *serialnr)
 	uint offset;
 
 	memset(serialnr, 0, sizeof(*serialnr));
-	if (eeprom_setup_layout())
+
+	if (cl_eeprom_setup_layout())
 		return;
 
-	offset = (eeprom_layout != LAYOUT_LEGACY) ?
-			BOARD_SERIAL_OFFSET : BOARD_SERIAL_OFFSET_LEGACY;
-	if (cm_t3x_eeprom_read(offset, (uchar *)serial, 8))
+	offset = (cl_eeprom_layout != LAYOUT_LEGACY) ?
+		BOARD_SERIAL_OFFSET : BOARD_SERIAL_OFFSET_LEGACY;
+
+	if (cl_eeprom_read(offset, (uchar *)serial, 8))
 		return;
 
 	if (serial[0] != 0xffffffff && serial[1] != 0xffffffff) {
@@ -71,45 +73,46 @@ void get_board_serial(struct tag_serialnr *serialnr)
 }
 
 /*
- * Routine: cm_t3x_eeprom_read_mac_addr
+ * Routine: cl_eeprom_read_mac_addr
  * Description: read mac address and store it in buf.
  */
-int cm_t3x_eeprom_read_mac_addr(uchar *buf)
+int cl_eeprom_read_mac_addr(uchar *buf)
 {
 	uint offset;
 
-	if (eeprom_setup_layout())
+	if (cl_eeprom_setup_layout())
 		return 0;
 
-	offset = (eeprom_layout != LAYOUT_LEGACY) ?
+	offset = (cl_eeprom_layout != LAYOUT_LEGACY) ?
 			MAC_ADDR_OFFSET : MAC_ADDR_OFFSET_LEGACY;
-	return cm_t3x_eeprom_read(offset, buf, 6);
+
+	return cl_eeprom_read(offset, buf, 6);
 }
 
 /*
- * Routine: cm_t3x_eeprom_get_board_rev
+ * Routine: cl_eeprom_get_board_rev
  * Description: read system revision from eeprom
  */
-u32 cm_t3x_eeprom_get_board_rev(void)
+u32 cl_eeprom_get_board_rev(void)
 {
 	u32 rev = 0;
 	char str[5]; /* Legacy representation can contain at most 4 digits */
 	uint offset = BOARD_REV_OFFSET_LEGACY;
 
-	if (eeprom_setup_layout())
+	if (cl_eeprom_setup_layout())
 		return 0;
 
-	if (eeprom_layout != LAYOUT_LEGACY)
+	if (cl_eeprom_layout != LAYOUT_LEGACY)
 		offset = BOARD_REV_OFFSET;
 
-	if (cm_t3x_eeprom_read(offset, (uchar *)&rev, BOARD_REV_SIZE))
+	if (cl_eeprom_read(offset, (uchar *)&rev, BOARD_REV_SIZE))
 		return 0;
 
 	/*
 	 * Convert legacy syntactic representation to semantic
 	 * representation. i.e. for rev 1.00: 0x100 --> 0x64
 	 */
-	if (eeprom_layout == LAYOUT_LEGACY) {
+	if (cl_eeprom_layout == LAYOUT_LEGACY) {
 		sprintf(str, "%x", rev);
 		rev = simple_strtoul(str, NULL, 10);
 	}
diff --git a/board/compulab/cm_t35/eeprom.h b/board/compulab/common/eeprom.h
index 02ffbb1..cf8c302 100644
--- a/board/compulab/cm_t35/eeprom.h
+++ b/board/compulab/common/eeprom.h
@@ -11,14 +11,14 @@
 #define _EEPROM_
 
 #ifdef CONFIG_DRIVER_OMAP34XX_I2C
-int cm_t3x_eeprom_read_mac_addr(uchar *buf);
-u32 cm_t3x_eeprom_get_board_rev(void);
+int cl_eeprom_read_mac_addr(uchar *buf);
+u32 cl_eeprom_get_board_rev(void);
 #else
-static inline int cm_t3x_eeprom_read_mac_addr(uchar *buf)
+static inline int cl_eeprom_read_mac_addr(uchar *buf)
 {
 	return 1;
 }
-static inline u32 cm_t3x_eeprom_get_board_rev(void)
+static inline u32 cl_eeprom_get_board_rev(void)
 {
 	return 0;
 }
diff --git a/board/compulab/cm_t35/display.c b/board/compulab/common/omap3_display.c
index fae8d95..ead821e 100644
--- a/board/compulab/cm_t35/display.c
+++ b/board/compulab/common/omap3_display.c
@@ -51,6 +51,7 @@ static const struct panel_config preset_dvi_640X480 = {
 	.lcd_size	= PANEL_LCD_SIZE(640, 480),
 	.timing_h	= DSS_HBP(48) | DSS_HFP(16) | DSS_HSW(96),
 	.timing_v	= DSS_VBP(33) | DSS_VFP(10) | DSS_VSW(2),
+	.pol_freq	= DSS_IHS | DSS_IVS | DSS_IPC,
 	.divisor	= 12 | (1 << 16),
 	.data_lines	= LCD_INTERFACE_24_BIT,
 	.panel_type	= ACTIVE_DISPLAY,
@@ -62,6 +63,7 @@ static const struct panel_config preset_dvi_800X600 = {
 	.lcd_size	= PANEL_LCD_SIZE(800, 600),
 	.timing_h	= DSS_HBP(88) | DSS_HFP(40) | DSS_HSW(128),
 	.timing_v	= DSS_VBP(23) | DSS_VFP(1) | DSS_VSW(4),
+	.pol_freq	= DSS_IHS | DSS_IVS | DSS_IPC,
 	.divisor	= 8 | (1 << 16),
 	.data_lines	= LCD_INTERFACE_24_BIT,
 	.panel_type	= ACTIVE_DISPLAY,
@@ -73,6 +75,7 @@ static const struct panel_config preset_dvi_1024X768 = {
 	.lcd_size	= PANEL_LCD_SIZE(1024, 768),
 	.timing_h	= DSS_HBP(160) | DSS_HFP(24) | DSS_HSW(136),
 	.timing_v	= DSS_VBP(29) | DSS_VFP(3) | DSS_VSW(6),
+	.pol_freq	= DSS_IHS | DSS_IVS | DSS_IPC,
 	.divisor	= 5 | (1 << 16),
 	.data_lines	= LCD_INTERFACE_24_BIT,
 	.panel_type	= ACTIVE_DISPLAY,
@@ -84,7 +87,8 @@ static const struct panel_config preset_dvi_1152X864 = {
 	.lcd_size	= PANEL_LCD_SIZE(1152, 864),
 	.timing_h	= DSS_HBP(256) | DSS_HFP(64) | DSS_HSW(128),
 	.timing_v	= DSS_VBP(32) | DSS_VFP(1) | DSS_VSW(3),
-	.divisor	= 3 | (1 << 16),
+	.pol_freq	= DSS_IHS | DSS_IVS | DSS_IPC,
+	.divisor	= 4 | (1 << 16),
 	.data_lines	= LCD_INTERFACE_24_BIT,
 	.panel_type	= ACTIVE_DISPLAY,
 	.load_mode	= 2,
@@ -95,6 +99,7 @@ static const struct panel_config preset_dvi_1280X960 = {
 	.lcd_size	= PANEL_LCD_SIZE(1280, 960),
 	.timing_h	= DSS_HBP(312) | DSS_HFP(96) | DSS_HSW(112),
 	.timing_v	= DSS_VBP(36) | DSS_VFP(1) | DSS_VSW(3),
+	.pol_freq	= DSS_IHS | DSS_IVS | DSS_IPC,
 	.divisor	= 3 | (1 << 16),
 	.data_lines	= LCD_INTERFACE_24_BIT,
 	.panel_type	= ACTIVE_DISPLAY,
@@ -106,6 +111,7 @@ static const struct panel_config preset_dvi_1280X1024 = {
 	.lcd_size	= PANEL_LCD_SIZE(1280, 1024),
 	.timing_h	= DSS_HBP(248) | DSS_HFP(48) | DSS_HSW(112),
 	.timing_v	= DSS_VBP(38) | DSS_VFP(1) | DSS_VSW(3),
+	.pol_freq	= DSS_IHS | DSS_IVS | DSS_IPC,
 	.divisor	= 3 | (1 << 16),
 	.data_lines	= LCD_INTERFACE_24_BIT,
 	.panel_type	= ACTIVE_DISPLAY,
diff --git a/board/corscience/tricorder/Makefile b/board/corscience/tricorder/Makefile
index d5316f8..266432d 100644
--- a/board/corscience/tricorder/Makefile
+++ b/board/corscience/tricorder/Makefile
@@ -8,4 +8,4 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
-obj-y	:= tricorder.o
+obj-y	:= tricorder.o tricorder-eeprom.o led.o
diff --git a/board/corscience/tricorder/led.c b/board/corscience/tricorder/led.c
new file mode 100644
index 0000000..30f2f50
--- /dev/null
+++ b/board/corscience/tricorder/led.c
@@ -0,0 +1,80 @@
+/*
+ * Copyright (c) 2013 Corscience GmbH & Co.KG
+ * Andreas Bießmann <andreas.biessmann@corscience.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#include <status_led.h>
+#include <twl4030.h>
+#include <asm/arch/cpu.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+
+#define TRICORDER_STATUS_LED_YELLOW 42
+#define TRICORDER_STATUS_LED_GREEN  43
+
+void __led_init(led_id_t mask, int state)
+{
+	__led_set(mask, state);
+}
+
+void __led_toggle(led_id_t mask)
+{
+	int toggle_gpio = 0;
+#ifdef STATUS_LED_BIT
+	if (!toggle_gpio && STATUS_LED_BIT & mask)
+		toggle_gpio = TRICORDER_STATUS_LED_GREEN;
+#endif
+#ifdef STATUS_LED_BIT1
+	if (!toggle_gpio && STATUS_LED_BIT1 & mask)
+		toggle_gpio = TRICORDER_STATUS_LED_YELLOW;
+#endif
+#ifdef STATUS_LED_BIT2
+	if (!toggle_gpio && STATUS_LED_BIT2 & mask) {
+		uint8_t val;
+		twl4030_i2c_read_u8(TWL4030_CHIP_LED, TWL4030_LED_LEDEN,
+				    &val);
+		val ^= (TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDAPWM);
+		twl4030_i2c_write_u8(TWL4030_CHIP_LED, TWL4030_LED_LEDEN,
+				     val);
+	}
+#endif
+	if (toggle_gpio) {
+		int state;
+		gpio_request(toggle_gpio, "");
+		state = gpio_get_value(toggle_gpio);
+		gpio_set_value(toggle_gpio, !state);
+	}
+}
+
+void __led_set(led_id_t mask, int state)
+{
+#ifdef STATUS_LED_BIT
+	if (STATUS_LED_BIT & mask) {
+		gpio_request(TRICORDER_STATUS_LED_GREEN, "");
+		gpio_direction_output(TRICORDER_STATUS_LED_GREEN, 0);
+		gpio_set_value(TRICORDER_STATUS_LED_GREEN, state);
+	}
+#endif
+#ifdef STATUS_LED_BIT1
+	if (STATUS_LED_BIT1 & mask) {
+		gpio_request(TRICORDER_STATUS_LED_YELLOW, "");
+		gpio_direction_output(TRICORDER_STATUS_LED_YELLOW, 0);
+		gpio_set_value(TRICORDER_STATUS_LED_YELLOW, state);
+	}
+#endif
+#ifdef STATUS_LED_BIT2
+	if (STATUS_LED_BIT2 & mask) {
+		if (STATUS_LED_OFF == state)
+			twl4030_i2c_write_u8(TWL4030_CHIP_LED,
+					     TWL4030_LED_LEDEN, 0);
+		else
+			twl4030_i2c_write_u8(TWL4030_CHIP_LED,
+					     TWL4030_LED_LEDEN,
+					     (TWL4030_LED_LEDEN_LEDAON |
+					      TWL4030_LED_LEDEN_LEDAPWM));
+	}
+#endif
+}
diff --git a/board/corscience/tricorder/tricorder-eeprom.c b/board/corscience/tricorder/tricorder-eeprom.c
new file mode 100644
index 0000000..1c74a0f
--- /dev/null
+++ b/board/corscience/tricorder/tricorder-eeprom.c
@@ -0,0 +1,251 @@
+/*
+ * (C) Copyright 2013
+ * Corscience GmbH & Co. KG, <www.corscience.de>
+ * Andreas Bießmann <andreas.biessmann@corscience.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#include <i2c.h>
+
+#include "tricorder-eeprom.h"
+
+static inline void warn_wrong_value(const char *msg, unsigned int a,
+		unsigned int b)
+{
+	printf("Expected EEPROM %s %08x, got %08x\n", msg, a, b);
+}
+
+static int handle_eeprom_v0(struct tricorder_eeprom *eeprom)
+{
+	struct tricorder_eeprom_v0 {
+		uint32_t magic;
+		uint16_t length;
+		uint16_t version;
+		char board_name[TRICORDER_BOARD_NAME_LENGTH];
+		char board_version[TRICORDER_BOARD_VERSION_LENGTH];
+		char board_serial[TRICORDER_BOARD_SERIAL_LENGTH];
+		uint32_t crc32;
+	} __packed eepromv0;
+	uint32_t crc;
+
+	printf("Old EEPROM (v0), consider rewrite!\n");
+
+	if (be16_to_cpu(eeprom->length) != sizeof(eepromv0)) {
+		warn_wrong_value("length", sizeof(eepromv0),
+				 be16_to_cpu(eeprom->length));
+		return 1;
+	}
+
+	memcpy(&eepromv0, eeprom, sizeof(eepromv0));
+
+	crc = crc32(0L, (unsigned char *)&eepromv0,
+		    sizeof(eepromv0) - sizeof(eepromv0.crc32));
+	if (be32_to_cpu(eepromv0.crc32) != crc) {
+		warn_wrong_value("CRC", be32_to_cpu(eepromv0.crc32),
+				 crc);
+		return 1;
+	}
+
+	/* Ok the content is correct, do the conversion */
+	memset(eeprom->interface_version, 0x0,
+	       TRICORDER_INTERFACE_VERSION_LENGTH);
+	crc = crc32(0L, (unsigned char *)eeprom, TRICORDER_EEPROM_CRC_SIZE);
+	eeprom->crc32 = cpu_to_be32(crc);
+
+	return 0;
+}
+
+static int handle_eeprom_v1(struct tricorder_eeprom *eeprom)
+{
+	uint32_t crc;
+
+	if (be16_to_cpu(eeprom->length) != TRICORDER_EEPROM_SIZE) {
+		warn_wrong_value("length", TRICORDER_EEPROM_SIZE,
+				 be16_to_cpu(eeprom->length));
+		return 1;
+	}
+
+	crc = crc32(0L, (unsigned char *)eeprom, TRICORDER_EEPROM_CRC_SIZE);
+	if (be32_to_cpu(eeprom->crc32) != crc) {
+		warn_wrong_value("CRC", be32_to_cpu(eeprom->crc32), crc);
+		return 1;
+	}
+
+	return 0;
+}
+
+int tricorder_get_eeprom(int addr, struct tricorder_eeprom *eeprom)
+{
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	unsigned int bus = i2c_get_bus_num();
+	i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM);
+#endif
+
+	memset(eeprom, 0, TRICORDER_EEPROM_SIZE);
+
+	i2c_read(addr, 0, 2, (unsigned char *)eeprom, TRICORDER_EEPROM_SIZE);
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	i2c_set_bus_num(bus);
+#endif
+
+	if (be32_to_cpu(eeprom->magic) != TRICORDER_EEPROM_MAGIC) {
+		warn_wrong_value("magic", TRICORDER_EEPROM_MAGIC,
+				 be32_to_cpu(eeprom->magic));
+		return 1;
+	}
+
+	switch (be16_to_cpu(eeprom->version)) {
+	case 0:
+		return handle_eeprom_v0(eeprom);
+	case 1:
+		return handle_eeprom_v1(eeprom);
+	default:
+		warn_wrong_value("version", TRICORDER_EEPROM_VERSION,
+				 be16_to_cpu(eeprom->version));
+		return 1;
+	}
+}
+
+#if !defined(CONFIG_SPL)
+int tricorder_eeprom_read(unsigned devaddr)
+{
+	struct tricorder_eeprom eeprom;
+	int ret = tricorder_get_eeprom(devaddr, &eeprom);
+
+	if (ret)
+		return ret;
+
+	printf("Board type:               %.*s\n",
+	       sizeof(eeprom.board_name), eeprom.board_name);
+	printf("Board version:            %.*s\n",
+	       sizeof(eeprom.board_version), eeprom.board_version);
+	printf("Board serial:             %.*s\n",
+	       sizeof(eeprom.board_serial), eeprom.board_serial);
+	printf("Board interface version:  %.*s\n",
+	       sizeof(eeprom.interface_version),
+	       eeprom.interface_version);
+
+	return ret;
+}
+
+int tricorder_eeprom_write(unsigned devaddr, const char *name,
+		const char *version, const char *serial, const char *interface)
+{
+	struct tricorder_eeprom eeprom, eeprom_verify;
+	size_t length;
+	uint32_t crc;
+	int ret;
+	unsigned char *p;
+	int i;
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	unsigned int bus;
+#endif
+
+	memset(eeprom, 0, TRICORDER_EEPROM_SIZE);
+	memset(eeprom_verify, 0, TRICORDER_EEPROM_SIZE);
+
+	eeprom.magic = cpu_to_be32(TRICORDER_EEPROM_MAGIC);
+	eeprom.length = cpu_to_be16(TRICORDER_EEPROM_SIZE);
+	eeprom.version = cpu_to_be16(TRICORDER_EEPROM_VERSION);
+
+	length = min(sizeof(eeprom.board_name), strlen(name));
+	strncpy(eeprom.board_name, name, length);
+
+	length = min(sizeof(eeprom.board_version), strlen(version));
+	strncpy(eeprom.board_version, version, length);
+
+	length = min(sizeof(eeprom.board_serial), strlen(serial));
+	strncpy(eeprom.board_serial, serial, length);
+
+	if (interface) {
+		length = min(sizeof(eeprom.interface_version),
+				strlen(interface));
+		strncpy(eeprom.interface_version, interface, length);
+	}
+
+	crc = crc32(0L, (unsigned char *)&eeprom, TRICORDER_EEPROM_CRC_SIZE);
+	eeprom.crc32 = cpu_to_be32(crc);
+
+#if defined(DEBUG)
+	puts("Tricorder EEPROM content:\n");
+	print_buffer(0, &eeprom, 1, sizeof(eeprom), 16);
+#endif
+
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	bus = i2c_get_bus_num();
+	i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM);
+#endif
+
+	/* do page write to the eeprom */
+	for (i = 0, p = (unsigned char *)&eeprom;
+	     i < sizeof(eeprom);
+	     i += 32, p += 32) {
+		ret = i2c_write(devaddr, i, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
+				p, min(sizeof(eeprom) - i, 32));
+		if (ret)
+			break;
+		udelay(5000); /* 5ms write cycle timing */
+	}
+
+	ret = i2c_read(devaddr, 0, 2, (unsigned char *)&eeprom_verify,
+			TRICORDER_EEPROM_SIZE);
+
+	if (memcmp(&eeprom, &eeprom_verify, sizeof(eeprom)) != 0) {
+		printf("Tricorder: Could not verify EEPROM content!\n");
+		ret = 1;
+	}
+
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	i2c_set_bus_num(bus);
+#endif
+	return ret;
+}
+
+int do_tricorder_eeprom(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	if (argc == 3) {
+		ulong dev_addr = simple_strtoul(argv[2], NULL, 16);
+		eeprom_init();
+		if (strcmp(argv[1], "read") == 0) {
+			int rcode;
+
+			rcode = tricorder_eeprom_read(dev_addr);
+
+			return rcode;
+		}
+	} else if (argc == 6 || argc == 7) {
+		ulong dev_addr = simple_strtoul(argv[2], NULL, 16);
+		char *name = argv[3];
+		char *version = argv[4];
+		char *serial = argv[5];
+		char *interface = NULL;
+		eeprom_init();
+
+		if (argc == 7)
+			interface = argv[6];
+
+		if (strcmp(argv[1], "write") == 0) {
+			int rcode;
+
+			rcode = tricorder_eeprom_write(dev_addr, name, version,
+					serial, interface);
+
+			return rcode;
+		}
+	}
+
+	return CMD_RET_USAGE;
+}
+
+U_BOOT_CMD(
+	tricordereeprom,	7,	1,	do_tricorder_eeprom,
+	"Tricorder EEPROM",
+	"read  devaddr\n"
+	"       - read Tricorder EEPROM at devaddr and print content\n"
+	"tricordereeprom write devaddr name version serial [interface]\n"
+	"       - write Tricorder EEPROM at devaddr with 'name', 'version'"
+	"and 'serial'\n"
+	"         optional add an HW interface parameter"
+);
+#endif /* CONFIG_SPL */
diff --git a/board/corscience/tricorder/tricorder-eeprom.h b/board/corscience/tricorder/tricorder-eeprom.h
new file mode 100644
index 0000000..06ed9a5
--- /dev/null
+++ b/board/corscience/tricorder/tricorder-eeprom.h
@@ -0,0 +1,41 @@
+/*
+ * (C) Copyright 2013
+ * Corscience GmbH & Co. KG, <www.corscience.de>
+ * Andreas Bießmann <andreas.biessmann@corscience.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef TRICORDER_EEPROM_H_
+#define TRICORDER_EEPROM_H_
+
+#include <linux/compiler.h>
+
+#define TRICORDER_EEPROM_MAGIC 0xc2a94f52
+#define TRICORDER_EEPROM_VERSION 1
+
+#define TRICORDER_BOARD_NAME_LENGTH		12
+#define TRICORDER_BOARD_VERSION_LENGTH		4
+#define TRICORDER_BOARD_SERIAL_LENGTH		12
+#define TRICORDER_INTERFACE_VERSION_LENGTH	4
+
+struct tricorder_eeprom {
+	uint32_t magic;
+	uint16_t length;
+	uint16_t version;
+	char board_name[TRICORDER_BOARD_NAME_LENGTH];
+	char board_version[TRICORDER_BOARD_VERSION_LENGTH];
+	char board_serial[TRICORDER_BOARD_SERIAL_LENGTH];
+	char interface_version[TRICORDER_INTERFACE_VERSION_LENGTH];
+	uint32_t crc32;
+} __packed;
+
+#define TRICORDER_EEPROM_SIZE		sizeof(struct tricorder_eeprom)
+#define TRICORDER_EEPROM_CRC_SIZE	(TRICORDER_EEPROM_SIZE - \
+					 sizeof(uint32_t))
+
+/**
+ * @brief read eeprom information from a specific eeprom address
+ */
+int tricorder_get_eeprom(int addr, struct tricorder_eeprom *eeprom);
+
+#endif /* TRICORDER_EEPROM_H_ */
diff --git a/board/corscience/tricorder/tricorder.c b/board/corscience/tricorder/tricorder.c
index c7099e5..2dfcb27 100644
--- a/board/corscience/tricorder/tricorder.c
+++ b/board/corscience/tricorder/tricorder.c
@@ -13,11 +13,13 @@
 #include <common.h>
 #include <twl4030.h>
 #include <asm/io.h>
+#include <asm/gpio.h>
 #include <asm/arch/mmc_host_def.h>
 #include <asm/arch/mux.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/arch/mem.h>
 #include "tricorder.h"
+#include "tricorder-eeprom.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -34,16 +36,91 @@ int board_init(void)
 	return 0;
 }
 
+/**
+ * get_eeprom - read the eeprom
+ *
+ * @eeprom - pointer to a eeprom struct to fill
+ *
+ * This function will panic() on wrong EEPROM content
+ */
+static void get_eeprom(struct tricorder_eeprom *eeprom)
+{
+	int ret;
+
+	if (!eeprom)
+		panic("No eeprom given!\n");
+
+	ret = gpio_request(7, "BMS");
+	if (ret)
+		panic("gpio: requesting BMS pin failed\n");
+
+	ret = gpio_direction_input(7);
+	if (ret)
+		panic("gpio: set BMS as input failed\n");
+
+	ret = gpio_get_value(7);
+	if (ret < 0)
+		panic("gpio: get BMS pin state failed\n");
+
+	gpio_free(7);
+
+	if (ret == 0) {
+		/* BMS is _not_ set, do the EEPROM check */
+		ret = tricorder_get_eeprom(0x51, eeprom);
+		if (!ret) {
+			if (strncmp(eeprom->board_name, "CS10411", 7) != 0)
+				panic("Wrong board name '%.*s'\n",
+				      sizeof(eeprom->board_name),
+						eeprom->board_name);
+			if (eeprom->board_version[0] < 'D')
+				panic("Wrong board version '%.*s'\n",
+				      sizeof(eeprom->board_version),
+						eeprom->board_version);
+		} else {
+			panic("Could not get board revision\n");
+		}
+	}
+}
+
+/**
+ * print_hwversion - print out a HW version string
+ *
+ * @eeprom - pointer to the eeprom
+ */
+static void print_hwversion(struct tricorder_eeprom *eeprom)
+{
+	size_t len;
+	if (!eeprom)
+		panic("No eeprom given!");
+
+	printf("Board %.*s:%.*s serial %.*s",
+	       sizeof(eeprom->board_name), eeprom->board_name,
+	       sizeof(eeprom->board_version), eeprom->board_version,
+	       sizeof(eeprom->board_serial), eeprom->board_serial);
+
+	len = strnlen(eeprom->interface_version,
+		      sizeof(eeprom->interface_version));
+	if (len > 0)
+		printf(" HW interface version %.*s",
+		       sizeof(eeprom->interface_version),
+		       eeprom->interface_version);
+	puts("\n");
+}
+
 /*
  * Routine: misc_init_r
  * Description: Configure board specific parts
  */
 int misc_init_r(void)
 {
+	struct tricorder_eeprom eeprom;
+	get_eeprom(&eeprom);
+	print_hwversion(&eeprom);
+
 	twl4030_power_init();
-#ifdef CONFIG_TWL4030_LED
-	twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
-#endif
+	status_led_set(0, STATUS_LED_ON);
+	status_led_set(1, STATUS_LED_ON);
+	status_led_set(2, STATUS_LED_ON);
 
 	dieid_num_r();
 
@@ -77,12 +154,43 @@ int board_mmc_init(bd_t *bis)
  */
 void get_board_mem_timings(struct board_sdrc_timings *timings)
 {
+	struct tricorder_eeprom eeprom;
+	get_eeprom(&eeprom);
+
 	/* General SDRC config */
-	timings->mcfg = MICRON_V_MCFG_165(128 << 20);
-	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+	if (eeprom.board_version[0] > 'D') {
+		/* use optimized timings for our SDRAM device */
+		timings->mcfg = MCFG((256 << 20), 14);
+#define MT46H64M32_TDAL  6	/* Twr/Tck + Trp/tck		*/
+				/* 15/6 + 18/6 = 5.5 -> 6	*/
+#define MT46H64M32_TDPL  3	/* 15/6 = 2.5 -> 3 (Twr)	*/
+#define MT46H64M32_TRRD  2	/* 12/6 = 2			*/
+#define MT46H64M32_TRCD  3	/* 18/6 = 3			*/
+#define MT46H64M32_TRP   3	/* 18/6 = 3			*/
+#define MT46H64M32_TRAS  7	/* 42/6 = 7			*/
+#define MT46H64M32_TRC  10	/* 60/6 = 10			*/
+#define MT46H64M32_TRFC 12	/* 72/6 = 12			*/
+		timings->ctrla = ACTIM_CTRLA(MT46H64M32_TRFC, MT46H64M32_TRC,
+					     MT46H64M32_TRAS, MT46H64M32_TRP,
+					     MT46H64M32_TRCD, MT46H64M32_TRRD,
+					     MT46H64M32_TDPL,
+					     MT46H64M32_TDAL);
+
+#define MT46H64M32_TWTR 1
+#define MT46H64M32_TCKE 1
+#define MT46H64M32_XSR 19	/* 112.5/6 = 18.75 => ~19	*/
+#define MT46H64M32_TXP 1
+		timings->ctrlb = ACTIM_CTRLB(MT46H64M32_TWTR, MT46H64M32_TCKE,
+					     MT46H64M32_TXP, MT46H64M32_XSR);
 
-	/* AC timings */
-	timings->ctrla = MICRON_V_ACTIMA_165;
-	timings->ctrlb = MICRON_V_ACTIMB_165;
-	timings->mr = MICRON_V_MR_165;
+		timings->mr = MICRON_V_MR_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+	} else {
+		/* use conservative beagleboard timings as default */
+		timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+		timings->ctrla = MICRON_V_ACTIMA_165;
+		timings->ctrlb = MICRON_V_ACTIMB_165;
+		timings->mr = MICRON_V_MR_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+	}
 }
diff --git a/board/corscience/tricorder/tricorder.h b/board/corscience/tricorder/tricorder.h
index 820a50c..67c35c5 100644
--- a/board/corscience/tricorder/tricorder.h
+++ b/board/corscience/tricorder/tricorder.h
@@ -75,8 +75,8 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(GPMC_A6),		(IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
 	MUX_VAL(CP(GPMC_A7),		(IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
 	MUX_VAL(CP(GPMC_A8),		(IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
-	MUX_VAL(CP(GPMC_A9),		(IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
-	MUX_VAL(CP(GPMC_A10),		(IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
+	MUX_VAL(CP(GPMC_A9),		(IDIS | PTU | EN  | M4)) /*GPIO 42*/\
+	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | EN  | M4)) /*GPIO 43*/\
 	MUX_VAL(CP(GPMC_D0),		(IEN  | PTD | DIS | M0)) /*GPMC_D0*/\
 	MUX_VAL(CP(GPMC_D1),		(IEN  | PTD | DIS | M0)) /*GPMC_D1*/\
 	MUX_VAL(CP(GPMC_D2),		(IEN  | PTD | DIS | M0)) /*GPMC_D2*/\
diff --git a/board/enbw/enbw_cmc/enbw_cmc.c b/board/enbw/enbw_cmc/enbw_cmc.c
index c477962..39efe20 100644
--- a/board/enbw/enbw_cmc/enbw_cmc.c
+++ b/board/enbw/enbw_cmc/enbw_cmc.c
@@ -36,6 +36,7 @@
 #include <asm/arch/hardware.h>
 #include <asm/arch/sdmmc_defs.h>
 #include <asm/arch/timer_defs.h>
+#include <asm/davinci_rtc.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
diff --git a/board/prodrive/pdnb3/Makefile b/board/ppcag/bg0900/Makefile
index 06120f3..74c6db5 100644
--- a/board/prodrive/pdnb3/Makefile
+++ b/board/ppcag/bg0900/Makefile
@@ -1,8 +1,12 @@
 #
-# (C) Copyright 2006
+# (C) Copyright 2000-2006
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
-obj-y	:= flash.o pdnb3.o nand.o
+ifndef	CONFIG_SPL_BUILD
+obj-y	:= bg0900.o
+else
+obj-y	:= spl_boot.o
+endif
diff --git a/board/ppcag/bg0900/bg0900.c b/board/ppcag/bg0900/bg0900.c
new file mode 100644
index 0000000..06612fa
--- /dev/null
+++ b/board/ppcag/bg0900/bg0900.c
@@ -0,0 +1,86 @@
+/*
+ * PPC-AG BG0900 board
+ *
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+int board_early_init_f(void)
+{
+	/* IO0 clock at 480MHz */
+	mxs_set_ioclk(MXC_IOCLK0, 480000);
+	/* IO1 clock at 480MHz */
+	mxs_set_ioclk(MXC_IOCLK1, 480000);
+
+	/* SSP2 clock at 160MHz */
+	mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	return mxs_dram_init();
+}
+
+int board_init(void)
+{
+	/* Adress of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+	struct mxs_clkctrl_regs *clkctrl_regs =
+		(struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;
+	struct eth_device *dev;
+	int ret;
+
+	ret = cpu_eth_init(bis);
+
+	/* BG0900 uses ENET_CLK PAD to drive FEC clock */
+	writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
+	       &clkctrl_regs->hw_clkctrl_enet);
+
+	/* Reset FEC PHYs */
+	gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
+	udelay(200);
+	gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
+
+	ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC0\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC0");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC0 device entry\n");
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+#endif
diff --git a/board/ppcag/bg0900/spl_boot.c b/board/ppcag/bg0900/spl_boot.c
new file mode 100644
index 0000000..a04c955
--- /dev/null
+++ b/board/ppcag/bg0900/spl_boot.c
@@ -0,0 +1,153 @@
+/*
+ * PPC-AG BG0900 Boot setup
+ *
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define	MUX_CONFIG_GPMI	(MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_NOPULL)
+#define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+#define	MUX_CONFIG_SSP2	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+
+const iomux_cfg_t iomux_setup[] = {
+	/* DUART */
+	MX28_PAD_PWM0__DUART_RX,
+	MX28_PAD_PWM1__DUART_TX,
+
+	/* GPMI NAND */
+	MX28_PAD_GPMI_D00__GPMI_D0 | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_D01__GPMI_D1 | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_D02__GPMI_D2 | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_D03__GPMI_D3 | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_D04__GPMI_D4 | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_D05__GPMI_D5 | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_D06__GPMI_D6 | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_D07__GPMI_D7 | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_CE0N__GPMI_CE0N | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_RDY0__GPMI_READY0 | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_RDN__GPMI_RDN |
+		(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
+	MX28_PAD_GPMI_WRN__GPMI_WRN | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_ALE__GPMI_ALE | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_CLE__GPMI_CLE | MUX_CONFIG_GPMI,
+	MX28_PAD_GPMI_RESETN__GPMI_RESETN | MUX_CONFIG_GPMI,
+
+	/* FEC0 */
+	MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+
+	/* FEC0 Reset */
+	MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* EMI */
+	MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+	MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+
+	/* SPI2 (for SPI flash) */
+	MX28_PAD_SSP2_SCK__SSP2_SCK | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MOSI__SSP2_CMD | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_MISO__SSP2_D0 | MUX_CONFIG_SSP2,
+	MX28_PAD_SSP2_SS0__SSP2_D3 |
+		(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
+};
+
+void mxs_adjust_memory_params(uint32_t *dram_vals)
+{
+	/*
+	 * DDR Controller Registers
+	 * Manufacturer:	Winbond
+	 * Device Part Number:	W972GG6JB-25I
+	 * Clock Freq.:		200MHz
+	 * Density:		2Gb
+	 * Chip Selects:	1
+	 * Number of Banks:	8
+	 * Row address:		14
+	 * Column address:	10
+	 */
+
+	dram_vals[0x74 / 4] = 0x0102010A;
+	dram_vals[0x98 / 4] = 0x04005003;
+	dram_vals[0x9c / 4] = 0x090000c8;
+
+	dram_vals[0xa8 / 4] = 0x0036b009;
+	dram_vals[0xac / 4] = 0x03270612;
+
+	dram_vals[0xb0 / 4] = 0x02020202;
+	dram_vals[0xb4 / 4] = 0x00c80029;
+
+	dram_vals[0xc0 / 4] = 0x00011900;
+
+	dram_vals[0x12c / 4] = 0x07400300;
+	dram_vals[0x130 / 4] = 0x07400300;
+	dram_vals[0x2c4 / 4] = 0x02030303;
+}
+
+void board_init_ll(const uint32_t arg, const uint32_t *resptr)
+{
+	mxs_common_spl_init(arg, resptr, iomux_setup, ARRAY_SIZE(iomux_setup));
+}
diff --git a/board/prodrive/pdnb3/flash.c b/board/prodrive/pdnb3/flash.c
deleted file mode 100644
index 75b5d05..0000000
--- a/board/prodrive/pdnb3/flash.c
+++ /dev/null
@@ -1,73 +0,0 @@
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/ixp425.h>
-
-#if !defined(CONFIG_FLASH_CFI_DRIVER)
-
-/*
- * include common flash code (for esd boards)
- */
-#include "../common/flash.c"
-
-/*
- * Prototypes
- */
-static ulong flash_get_size (vu_long * addr, flash_info_t * info);
-
-static inline ulong ld(ulong x)
-{
-	ulong k = 0;
-
-	while (x >>= 1)
-		++k;
-
-	return k;
-}
-
-unsigned long flash_init(void)
-{
-	unsigned long size;
-	int i;
-
-	/* Init: no FLASHes known */
-	for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; i++)
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-
-	size = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
-
-	if (flash_info[0].flash_id == FLASH_UNKNOWN)
-		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size, size<<20);
-
-	/* Reconfigure CS0 to actual FLASH size */
-	*IXP425_EXP_CS0 = (*IXP425_EXP_CS0 & ~0x00003C00) | ((ld(size) - 9) << 10);
-
-	/* Monitor protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
-		      &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
-
-	/* Environment protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CONFIG_ENV_ADDR,
-		      CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
-		      &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
-
-	/* Redundant environment protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CONFIG_ENV_ADDR_REDUND,
-		      CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1,
-		      &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
-
-	flash_info[0].size = size;
-
-	return size;
-}
-
-#endif /* CONFIG_FLASH_CFI_DRIVER */
diff --git a/board/prodrive/pdnb3/nand.c b/board/prodrive/pdnb3/nand.c
deleted file mode 100644
index e1d2c63..0000000
--- a/board/prodrive/pdnb3/nand.c
+++ /dev/null
@@ -1,129 +0,0 @@
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <nand.h>
-
-struct pdnb3_ndfc_regs {
-	uchar cmd;
-	uchar wait;
-	uchar addr;
-	uchar term;
-	uchar data;
-};
-
-static u8 hwctl;
-static struct pdnb3_ndfc_regs *pdnb3_ndfc;
-
-#define readb(addr)	*(volatile u_char *)(addr)
-#define readl(addr)	*(volatile u_long *)(addr)
-#define writeb(d,addr)	*(volatile u_char *)(addr) = (d)
-
-/*
- * The PDNB3 has a NAND Flash Controller (NDFC) that handles all accesses to
- * the NAND devices.  The NDFC has command, address and data registers that
- * when accessed will set up the NAND flash pins appropriately.  We'll use the
- * hwcontrol function to save the configuration in a global variable.
- * We can then use this information in the read and write functions to
- * determine which NDFC register to access.
- *
- * There is one NAND devices on the board, a Hynix HY27US08561A (32 MByte).
- */
-static void pdnb3_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
-	struct nand_chip *this = mtd->priv;
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		if ( ctrl & NAND_CLE )
-			hwctl |= 0x1;
-		else
-			hwctl &= ~0x1;
-		if ( ctrl & NAND_ALE )
-			hwctl |= 0x2;
-		else
-			hwctl &= ~0x2;
-		if ( (ctrl & NAND_NCE) != NAND_NCE)
-			writeb(0x00, &(pdnb3_ndfc->term));
-	}
-	if (cmd != NAND_CMD_NONE)
-		writeb(cmd, this->IO_ADDR_W);
-}
-
-
-static u_char pdnb3_nand_read_byte(struct mtd_info *mtd)
-{
-	return readb(&(pdnb3_ndfc->data));
-}
-
-static void pdnb3_nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
-{
-	int i;
-
-	for (i = 0; i < len; i++) {
-		if (hwctl & 0x1)
-			writeb(buf[i], &(pdnb3_ndfc->cmd));
-		else if (hwctl & 0x2)
-			writeb(buf[i], &(pdnb3_ndfc->addr));
-		else
-			writeb(buf[i], &(pdnb3_ndfc->data));
-	}
-}
-
-static void pdnb3_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len)
-{
-	int i;
-
-	for (i = 0; i < len; i++)
-		buf[i] = readb(&(pdnb3_ndfc->data));
-}
-
-static int pdnb3_nand_verify_buf(struct mtd_info *mtd, const u_char *buf, int len)
-{
-	int i;
-
-	for (i = 0; i < len; i++)
-		if (buf[i] != readb(&(pdnb3_ndfc->data)))
-			return i;
-
-	return 0;
-}
-
-static int pdnb3_nand_dev_ready(struct mtd_info *mtd)
-{
-	/*
-	 * Blocking read to wait for NAND to be ready
-	 */
-	readb(&(pdnb3_ndfc->wait));
-
-	/*
-	 * Return always true
-	 */
-	return 1;
-}
-
-int board_nand_init(struct nand_chip *nand)
-{
-	pdnb3_ndfc = (struct pdnb3_ndfc_regs *)CONFIG_SYS_NAND_BASE;
-
-	nand->ecc.mode = NAND_ECC_SOFT;
-
-	/* Set address of NAND IO lines (Using Linear Data Access Region) */
-	nand->IO_ADDR_R = (void __iomem *) ((ulong) pdnb3_ndfc + 0x4);
-	nand->IO_ADDR_W = (void __iomem *) ((ulong) pdnb3_ndfc + 0x4);
-	/* Reference hardware control function */
-	nand->cmd_ctrl   = pdnb3_nand_hwcontrol;
-	nand->read_byte  = pdnb3_nand_read_byte;
-	nand->write_buf  = pdnb3_nand_write_buf;
-	nand->read_buf   = pdnb3_nand_read_buf;
-	nand->verify_buf = pdnb3_nand_verify_buf;
-	nand->dev_ready  = pdnb3_nand_dev_ready;
-	return 0;
-}
-#endif
diff --git a/board/prodrive/pdnb3/pdnb3.c b/board/prodrive/pdnb3/pdnb3.c
deleted file mode 100644
index fa320da..0000000
--- a/board/prodrive/pdnb3/pdnb3.c
+++ /dev/null
@@ -1,220 +0,0 @@
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* predefine these here for FPGA programming (before including fpga.c) */
-#define SET_FPGA(data)	*IXP425_GPIO_GPOUTR = (data)
-#define FPGA_DONE_STATE (*IXP425_GPIO_GPINR & CONFIG_SYS_FPGA_DONE)
-#define FPGA_INIT_STATE (*IXP425_GPIO_GPINR & CONFIG_SYS_FPGA_INIT)
-#define OLD_VAL		old_val
-
-static unsigned long old_val = 0;
-
-/*
- * include common fpga code (for prodrive boards)
- */
-#include "../common/fpga.c"
-
-/*
- * Miscelaneous platform dependent initialisations
- */
-int board_init(void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x00000100;
-
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_FPGA_RESET);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_FPGA_RESET);
-
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_SYS_RUNNING);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_SYS_RUNNING);
-
-	/*
-	 * Setup GPIO's for FPGA programming
-	 */
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PRG);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_CLK);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DATA);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PRG);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_CLK);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DATA);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_INIT);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DONE);
-
-	/*
-	 * Setup GPIO's for interrupts
-	 */
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RESTORE_INT);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RESTORE_INT);
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RESTART_INT);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RESTART_INT);
-
-	/*
-	 * Setup GPIO's for 33MHz clock output
-	 */
-	*IXP425_GPIO_GPCLKR = 0x01FF0000;
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_CLK_33M);
-
-	/*
-	 * Setup other chip select's
-	 */
-	*IXP425_EXP_CS1 = CONFIG_SYS_EXP_CS1;
-
-	return 0;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-
-	puts("Board: PDNB3");
-
-	if (i > 0) {
-		puts(", serial# ");
-		puts(buf);
-	}
-	putc('\n');
-
-	return (0);
-}
-
-int dram_init(void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size  = PHYS_SDRAM_1_SIZE;
-
-	return (0);
-}
-
-int do_fpga_boot(unsigned char *fpgadata)
-{
-	unsigned char *dst;
-	int status;
-	int index;
-	int i;
-	ulong len = CONFIG_SYS_MALLOC_LEN;
-
-	/*
-	 * Setup GPIO's for FPGA programming
-	 */
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PRG);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_CLK);
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DATA);
-
-	/*
-	 * Save value so no readback is required upon programming
-	 */
-	old_val = *IXP425_GPIO_GPOUTR;
-
-	/*
-	 * First try to decompress fpga image (gzip compressed?)
-	 */
-	dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
-	if (gunzip(dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
-		printf("Error: Image has to be gzipp'ed!\n");
-		return -1;
-	}
-
-	status = fpga_boot(dst, len);
-	if (status != 0) {
-		printf("\nFPGA: Booting failed ");
-		switch (status) {
-		case ERROR_FPGA_PRG_INIT_LOW:
-			printf("(Timeout: INIT not low after asserting PROGRAM*)\n ");
-			break;
-		case ERROR_FPGA_PRG_INIT_HIGH:
-			printf("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
-			break;
-		case ERROR_FPGA_PRG_DONE:
-			printf("(Timeout: DONE not high after programming FPGA)\n ");
-			break;
-		}
-
-		/* display infos on fpgaimage */
-		index = 15;
-		for (i=0; i<4; i++) {
-			len = dst[index];
-			printf("FPGA: %s\n", &(dst[index+1]));
-			index += len+3;
-		}
-		putc ('\n');
-		/* delayed reboot */
-		for (i=5; i>0; i--) {
-			printf("Rebooting in %2d seconds \r",i);
-			for (index=0;index<1000;index++)
-				udelay(1000);
-		}
-		putc('\n');
-		do_reset(NULL, 0, 0, NULL);
-	}
-
-	puts("FPGA:  ");
-
-	/* display infos on fpgaimage */
-	index = 15;
-	for (i=0; i<4; i++) {
-		len = dst[index];
-		printf("%s ", &(dst[index+1]));
-		index += len+3;
-	}
-	putc('\n');
-
-	free(dst);
-
-	/*
-	 * Reset FPGA
-	 */
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_FPGA_RESET);
-	udelay(10);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_FPGA_RESET);
-
-	return (0);
-}
-
-int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	ulong addr;
-
-	if (argc < 2)
-		return cmd_usage(cmdtp);
-
-	addr = simple_strtoul(argv[1], NULL, 16);
-
-	return do_fpga_boot((unsigned char *)addr);
-}
-
-U_BOOT_CMD(
-	fpga,     2,     0,      do_fpga,
-	"boot FPGA",
-	"address size\n    - boot FPGA with gzipped image at <address>"
-);
-
-#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
-extern struct pci_controller hose;
-extern void pci_ixp_init(struct pci_controller * hose);
-
-void pci_init_board(void)
-{
-	extern void pci_ixp_init (struct pci_controller *hose);
-
-	pci_ixp_init(&hose);
-}
-#endif
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index c2fc5a6..57fedab 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -28,6 +28,8 @@
 #include <cpsw.h>
 #include <power/tps65217.h>
 #include <power/tps65910.h>
+#include <environment.h>
+#include <watchdog.h>
 #include "board.h"
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -485,6 +487,10 @@ int board_init(void)
 		STNOR_GPMC_CONFIG5, STNOR_GPMC_CONFIG6, STNOR_GPMC_CONFIG7 };
 #endif
 
+#if defined(CONFIG_HW_WATCHDOG)
+	hw_watchdog_init();
+#endif
+
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
 	gpmc_init();
diff --git a/board/udoo/Makefile b/board/udoo/Makefile
new file mode 100644
index 0000000..80efada
--- /dev/null
+++ b/board/udoo/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := udoo.o
diff --git a/board/udoo/udoo.c b/board/udoo/udoo.c
new file mode 100644
index 0000000..e9d6375
--- /dev/null
+++ b/board/udoo/udoo.c
@@ -0,0 +1,110 @@
+/*
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define WDT_EN		IMX_GPIO_NR(5, 4)
+#define WDT_TRG		IMX_GPIO_NR(3, 19)
+
+int dram_init(void)
+{
+	gd->ram_size = (phys_size_t)CONFIG_DDR_MB * 1024 * 1024;
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart2_pads[] = {
+	MX6_PAD_EIM_D26__UART2_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D27__UART2_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__USDHC3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__USDHC3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	MX6_PAD_EIM_A24__GPIO_5_4 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D19__GPIO_3_19,
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+}
+
+static void setup_iomux_wdog(void)
+{
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+	gpio_direction_output(WDT_TRG, 0);
+	gpio_direction_output(WDT_EN, 1);
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg = { USDHC3_BASE_ADDR };
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	return 1; /* Always present */
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+	usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+	usdhc_cfg.max_bus_width = 4;
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg);
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_wdog();
+	setup_iomux_uart();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: Udoo\n");
+
+	return 0;
+}
diff --git a/board/wandboard/README b/board/wandboard/README
index 498db2f..1f678e1 100644
--- a/board/wandboard/README
+++ b/board/wandboard/README
@@ -3,8 +3,8 @@ U-Boot for Wandboard
 
 This file contains information for the port of U-Boot to the Wandboard.
 
-Wandboard is a development board that has two variants: one version based
-on mx6 dual lite and another one based on mx6 solo.
+Wandboard is a development board that has three variants based on the following
+SoCs: mx6 quad, mx6 dual lite and mx6 solo.
 
 For more details about Wandboard, please refer to:
 http://www.wandboard.org/