Merge branch 'master' of git://88.191.163.10/u-boot-arm

Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.

Conflicts:
	arch/arm/include/asm/arch-am33xx/hardware.h

Signed-off-by: Tom Rini <trini@ti.com>

40 files changed, 2106 insertions, 1226 deletions

diff --git a/board/Barix/ipam390/Makefile b/board/Barix/ipam390/Makefile
new file mode 100644
index 0000000..c84ee05
--- /dev/null
+++ b/board/Barix/ipam390/Makefile
@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	+= ipam390.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+# This is for $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Barix/ipam390/README.ipam390 b/board/Barix/ipam390/README.ipam390
new file mode 100644
index 0000000..2d155a3
--- /dev/null
+++ b/board/Barix/ipam390/README.ipam390
@@ -0,0 +1,229 @@
+Summary
+=======
+The README is for the boot procedure on the ipam390 board
+
+In the context of U-Boot, the board is booted in three stages. The initial
+bootloader which executes upon reset is the ROM Boot Loader (RBL) and sits
+in the internal ROM. The RBL initializes the internal memory and then
+depending on the exact board and pin configurations will initialize another
+controller (such as NAND) to continue the boot process by loading
+the secondary program loader (SPL). The SPL will initialize the system
+further (some clocks, SDRAM). As on this board is used the falcon boot
+mode, now 2 ways are possible depending on the GPIO 7_14 input pin,
+connected with the "soft reset switch"
+
+If this pin is logical 1 (high level):
+spl code starts the kernel image without delay
+
+If this pin is logical 0 (low level):
+spl code starts the u-boot image
+
+AIS is an image format defined by TI for the images that are to be loaded
+to memory by the RBL. The image is divided into a series of sections and
+the image's entry point is specified. Each section comes with meta data
+like the target address the section is to be copied to and the size of the
+section, which is used by the RBL to load the image. At the end of the
+image the RBL jumps to the image entry point.  The AIS format allows for
+other things such as programming the clocks and SDRAM if the header is
+programmed for it.  We do not take advantage of this and instead use SPL as
+it allows for additional flexibility (run-time detect of board revision,
+loading the next image from a different media, etc).
+
+Compilation
+===========
+run "./MAKEALL ipam390" in the u-boot source tree.
+Once this build completes you will have a u-boot.ais file that needs to
+be written to the nand flash.
+
+Flashing the images to NAND
+==========================
+The AIS image can be written to NAND flash using the following commands.
+Assuming that the network is configured and enabled and the u-boot.ais file
+is tftp'able.
+
+U-Boot > print upd_uboot
+upd_uboot=tftp c0000000 ${u-boot};nand erase.part u-boot;nand write c0000000 20000 ${filesize}
+U-Boot >
+U-Boot > run upd_uboot
+Using DaVinci-EMAC device
+TFTP from server 192.168.1.1; our IP address is 192.168.20.71
+Filename '/tftpboot/ipam390/u-boot.ais'.
+Load address: 0xc0000000
+Loading: ##################################
+         1.5 MiB/s
+done
+Bytes transferred = 493716 (78894 hex)
+
+NAND erase.part: device 0 offset 0x20000, size 0x160000
+Erasing at 0x160000 -- 100% complete.
+OK
+
+NAND write: device 0 offset 0x20000, size 0x78894
+ 493716 bytes written: OK
+U-Boot >
+
+Recovery
+========
+
+In the case of a "bricked" board, you need to use the TI tools found
+here[1] to create an uboot-uart-ais.bin file
+
+- cd to the u-boot source tree
+
+- compile the u-boot for the ipam390 board:
+$ ./MAKEALL ipam390
+
+  -> Now we shall have u-boot.bin
+
+- Create u-boot-uart-ais.bin
+$ mono HexAIS_OMAP-L138.exe -entrypoint 0xC1080000 -ini
+ipam390-ais-uart.cfg -o ./uboot-uart-ais.bin ./u-boot.bin@0xC1080000;
+
+Note: The ipam390-ais-uart.cfg is found in the board directory
+for the ipam390 board, u-boot:/board/Barix/ipam390/ipam390-ais-uart.cfg
+
+- We can now run bootloader on IPAM390 via UART using the command below:
+
+$ mono ./slh_OMAP-L138.exe -waitForDevice -v -p /dev/tty.UC-232AC uboot-uart-ais.bin
+NOTE: Do not cancel the command execution! The command takes 20+ seconds
+to upload u-boot over serial and run it!
+Outcome:
+Waiting for the OMAP-L138...
+(AIS Parse): Read magic word 0x41504954.
+(AIS Parse): Waiting for BOOTME... (power on or reset target now)
+(AIS Parse): BOOTME received!
+(AIS Parse): Performing Start-Word Sync...
+(AIS Parse): Performing Ping Opcode Sync...
+(AIS Parse): Processing command 0: 0x5853590D.
+(AIS Parse): Performing Opcode Sync...
+(AIS Parse): Executing function...
+(AIS Parse): Processing command 1: 0x5853590D.
+(AIS Parse): Performing Opcode Sync...
+(AIS Parse): Executing function...
+(AIS Parse): Processing command 2: 0x5853590D.
+(AIS Parse): Performing Opcode Sync...
+(AIS Parse): Executing function...
+(AIS Parse): Processing command 3: 0x5853590D.
+(AIS Parse): Performing Opcode Sync...
+(AIS Parse): Executing function...
+(AIS Parse): Processing command 4: 0x5853590D.
+(AIS Parse): Performing Opcode Sync...
+(AIS Parse): Executing function...
+(AIS Parse): Processing command 5: 0x58535901.
+(AIS Parse): Performing Opcode Sync...
+(AIS Parse): Loading section...
+(AIS Parse): Loaded 326516-Byte section to address 0xC1080000.
+(AIS Parse): Processing command 6: 0x58535906.
+(AIS Parse): Performing Opcode Sync...
+(AIS Parse): Performing jump and close...
+(AIS Parse): AIS complete. Jump to address 0xC1080000.
+(AIS Parse): Waiting for DONE...
+(AIS Parse): Boot completed successfully.
+
+Operation completed successfully.
+
+Falcon Bootmode (boot linux without booting U-Boot)
+===================================================
+
+The Falcon Mode extends this way allowing to start the Linux kernel directly
+from SPL. A new command is added to U-Boot to prepare the parameters that SPL
+must pass to the kernel, using ATAGS or Device Tree.
+
+In normal mode, these parameters are generated each time before
+loading the kernel, passing to Linux the address in memory where
+the parameters can be read.
+With Falcon Mode, this snapshot can be saved into persistent storage and SPL is
+informed to load it before running the kernel.
+
+To boot the kernel, these steps under a Falcon-aware U-Boot are required:
+
+1. Boot the board into U-Boot.
+Use the "spl export" command to generate the kernel parameters area or the DT.
+U-Boot runs as when it boots the kernel, but stops before passing the control
+to the kernel.
+
+Here the command sequence for the ipam390 board:
+- load the linux kernel image into ram:
+
+U-Boot > nand read c0100000 2 200000 400000
+
+NAND read: device 0 offset 0x200000, size 0x400000
+ 4194304 bytes read: OK
+
+- generate the bootparms image:
+
+U-Boot > spl export atags c0100000
+## Booting kernel from Legacy Image at c0100000 ...
+   Image Name:   Linux-3.5.1
+   Image Type:   ARM Linux Kernel Image (uncompressed)
+   Data Size:    2504280 Bytes = 2.4 MiB
+   Load Address: c0008000
+   Entry Point:  c0008000
+   Verifying Checksum ... OK
+   Loading Kernel Image ... OK
+subcommand not supported
+subcommand not supported
+Argument image is now in RAM at: 0xc0000100
+
+- copy the bootparms image into nand:
+
+U-Boot > mtdparts
+
+device nand0 <davinci_nand.0>, # parts = 6
+ #: name		size		offset		mask_flags
+ 0: u-boot-env          0x00020000	0x00000000	0
+ 1: u-boot              0x00160000	0x00020000	0
+ 2: bootparms           0x00020000	0x00180000	0
+ 3: factory-info        0x00060000	0x001a0000	0
+ 4: kernel              0x00400000	0x00200000	0
+ 5: rootfs              0x07a00000	0x00600000	0
+
+active partition: nand0,0 - (u-boot-env) 0x00020000 @ 0x00000000
+
+defaults:
+mtdids  : nand0=davinci_nand.0
+mtdparts: mtdparts=davinci_nand.0:128k(u-boot-env),1408k(u-boot),128k(bootparms),384k(factory-info),4M(kernel),-(rootfs)
+U-Boot > nand erase.part bootparms
+
+NAND erase.part: device 0 offset 0x180000, size 0x20000
+Erasing at 0x180000 -- 100% complete.
+OK
+U-Boot > nand write c0000100 180000 20000
+
+NAND write: device 0 offset 0x180000, size 0x20000
+ 131072 bytes written: OK
+U-Boot >
+
+You can use also the predefined U-Boot Environment variable "setbootparms",
+which will do all the above steps in one command:
+
+U-Boot > print setbootparms
+setbootparms=nand read c0100000 200000 400000;spl export atags c0100000;nand erase.part bootparms;nand write c0000100 180000 20000
+U-Boot > run setbootparms
+
+NAND read: device 0 offset 0x200000, size 0x400000
+ 4194304 bytes read: OK
+## Booting kernel from Legacy Image at c0100000 ...
+   Image Name:   Linux-3.5.1
+   Image Type:   ARM Linux Kernel Image (uncompressed)
+   Data Size:    2504280 Bytes = 2.4 MiB
+   Load Address: c0008000
+   Entry Point:  c0008000
+   Verifying Checksum ... OK
+   Loading Kernel Image ... OK
+subcommand not supported
+subcommand not supported
+Argument image is now in RAM at: 0xc0000100
+
+NAND erase.part: device 0 offset 0x180000, size 0x20000
+Erasing at 0x180000 -- 100% complete.
+OK
+
+NAND write: device 0 offset 0x180000, size 0x20000
+ 131072 bytes written: OK
+U-Boot >
+
+Links
+=====
+[1]
+ http://sourceforge.net/projects/dvflashutils/files/OMAP-L138/
diff --git a/board/Barix/ipam390/ipam390-ais-uart.cfg b/board/Barix/ipam390/ipam390-ais-uart.cfg
new file mode 100644
index 0000000..e1a99f2
--- /dev/null
+++ b/board/Barix/ipam390/ipam390-ais-uart.cfg
@@ -0,0 +1,202 @@
+; General settings that can be overwritten in the host code
+; that calls the AISGen library.
+[General]
+
+; Can be 8 or 16 - used in emifa
+busWidth=8
+
+; SPIMASTER,I2CMASTER,EMIFA,NAND,EMAC,UART,PCI,HPI,USB,MMC_SD,VLYNQ,RAW
+BootMode=UART
+
+; 8,16,24 - used for SPI,I2C
+;AddrWidth=8
+
+; NO_CRC,SECTION_CRC,SINGLE_CRC
+crcCheckType=NO_CRC
+
+; This section allows setting the PLL0 system clock with a
+; specified multiplier and divider as shown. The clock source
+; can also be chosen for internal or external.
+;           |------24|------16|-------8|-------0|
+; PLL0CFG0: | CLKMODE| PLLM   | PREDIV | POSTDIV|
+; PLL0CFG1: | RSVD   | PLLDIV1| PLLDIV3| PLLDIV7|
+;[PLL0CONFIG]
+;PLL0CFG0 = 0x00180001
+;PLL0CFG1 = 0x00000205
+
+[PLLANDCLOCKCONFIG]
+PLL0CFG0 = 0x00180001
+PLL0CFG1 = 0x00000205
+PERIPHCLKCFG = 0x00000051
+
+; This section allows setting up the PLL1. Usually this will
+; take place as part of the EMIF3a DDR setup. The format of
+; the input args is as follows:
+;           |------24|------16|-------8|-------0|
+; PLL1CFG0: |    PLLM| POSTDIV| PLLDIV1| PLLDIV2|
+; PLL1CFG1: |           RSVD           | PLLDIV3|
+[PLL1CONFIG]
+PLL1CFG0 = 0x18010001
+PLL1CFG1 = 0x00000002
+
+; This section lets us configure the peripheral interface
+; of the current booting peripheral (I2C, SPI, or UART).
+; Use with caution. The format of the PERIPHCLKCFG field
+; is as follows:
+; SPI:        |------24|------16|-------8|-------0|
+;             |           RSVD           |PRESCALE|
+;
+; I2C:        |------24|------16|-------8|-------0|
+;             |  RSVD  |PRESCALE|  CLKL  |  CLKH  |
+;
+; UART:       |------24|------16|-------8|-------0|
+;             | RSVD   |  OSR   |  DLH   |  DLL   |
+[PERIPHCLKCFG]
+PERIPHCLKCFG = 0x00000051
+
+; This section can be used to configure the PLL1 and the EMIF3a registers
+; for starting the DDR2 interface.
+; See PLL1CONFIG section for the format of the PLL1CFG fields.
+;            |------24|------16|-------8|-------0|
+; PLL1CFG0:  |              PLL1CFG              |
+; PLL1CFG1:  |              PLL1CFG              |
+; DDRPHYC1R: |             DDRPHYC1R             |
+; SDCR:      |              SDCR                 |
+; SDTIMR:    |              SDTIMR               |
+; SDTIMR2:   |              SDTIMR2              |
+; SDRCR:     |              SDRCR                |
+; CLK2XSRC:  |             CLK2XSRC              |
+[EMIF3DDR]
+PLL1CFG0 = 0x18010001
+PLL1CFG1 = 0x00000002
+DDRPHYC1R = 0x000000C2
+SDCR = 0x0017C432
+SDTIMR = 0x26922A09
+SDTIMR2 = 0x4414C722
+SDRCR = 0x00000498
+CLK2XSRC = 0x00000000
+
+; This section can be used to configure the EMIFA to use
+; CS0 as an SDRAM interface.  The fields required to do this
+; are given below.
+;                     |------24|------16|-------8|-------0|
+; SDBCR:              |               SDBCR               |
+; SDTIMR:             |               SDTIMR              |
+; SDRSRPDEXIT:        |             SDRSRPDEXIT           |
+; SDRCR:              |               SDRCR               |
+; DIV4p5_CLK_ENABLE:  |         DIV4p5_CLK_ENABLE         |
+;[EMIF25SDRAM]
+;SDBCR = 0x00004421
+;SDTIMR = 0x42215810
+;SDRSRPDEXIT = 0x00000009
+;SDRCR = 0x00000410
+;DIV4p5_CLK_ENABLE = 0x00000001
+
+; This section can be used to configure the async chip selects
+; of the EMIFA (CS2-CS5).  The fields required to do this
+; are given below.
+;           |------24|------16|-------8|-------0|
+; A1CR:     |                A1CR               |
+; A2CR:     |                A2CR               |
+; A3CR:     |                A3CR               |
+; A4CR:     |                A4CR               |
+; NANDFCR:  |              NANDFCR              |
+;[EMIF25ASYNC]
+;A1CR = 0x00000000
+;A2CR = 0x00000000
+;A3CR = 0x00000000
+;A4CR = 0x00000000
+;NANDFCR = 0x00000000
+[EMIF25ASYNC]
+A1CR = 0x00000000
+A2CR = 0x3FFFFFFE
+A3CR = 0x00000000
+A4CR = 0x00000000
+NANDFCR = 0x00000012
+
+; This section should be used in place of PLL0CONFIG when
+; the I2C, SPI, or UART modes are being used.  This ensures that
+; the system PLL and the peripheral's clocks are changed together.
+; See PLL0CONFIG section for the format of the PLL0CFG fields.
+; See PERIPHCLKCFG section for the format of the CLKCFG field.
+;               |------24|------16|-------8|-------0|
+; PLL0CFG0:     |              PLL0CFG              |
+; PLL0CFG1:     |              PLL0CFG              |
+; PERIPHCLKCFG: |              CLKCFG               |
+;[PLLANDCLOCKCONFIG]
+;PLL0CFG0 = 0x00180001
+;PLL0CFG1 = 0x00000205
+;PERIPHCLKCFG = 0x00010032
+
+; This section should be used to setup the power state of modules
+; of the two PSCs.  This section can be included multiple times to
+; allow the configuration of any or all of the device modules.
+;           |------24|------16|-------8|-------0|
+; LPSCCFG:  | PSCNUM | MODULE |   PD   | STATE  |
+;[PSCCONFIG]
+;LPSCCFG=
+
+; This section allows setting of a single PINMUX register.
+; This section can be included multiple times to allow setting
+; as many PINMUX registers as needed.
+;         |------24|------16|-------8|-------0|
+; REGNUM: |              regNum               |
+; MASK:   |               mask                |
+; VALUE:  |              value                |
+;[PINMUX]
+;REGNUM = 5
+;MASK = 0x00FF0000
+;VALUE = 0x00880000
+
+; No Params required - simply include this section for the fast boot
+; function to be called
+;[FASTBOOT]
+
+; This section allows setting up the PLL1. Usually this will
+; take place as part of the EMIF3a DDR setup. The format of
+; the input args is as follows:
+;           |------24|------16|-------8|-------0|
+; PLL1CFG0: |    PLLM| POSTDIV| PLLDIV1| PLLDIV2|
+; PLL1CFG1: |           RSVD           | PLLDIV3|
+;[PLL1CONFIG]
+;PLL1CFG0 = 0x15010001
+;PLL1CFG1 = 0x00000002
+
+; This section can be used to configure the PLL1 and the EMIF3a registers
+; for starting the DDR2 interface on ARM-boot D800K002 devices.
+;            |------24|------16|-------8|-------0|
+; DDRPHYC1R: |             DDRPHYC1R             |
+; SDCR:      |              SDCR                 |
+; SDTIMR:    |              SDTIMR               |
+; SDTIMR2:   |              SDTIMR2              |
+; SDRCR:     |              SDRCR                |
+; CLK2XSRC:  |             CLK2XSRC              |
+;[ARM_EMIF3DDR_PATCHFXN]
+;DDRPHYC1R = 0x000000C2
+;SDCR = 0x0017C432
+;SDTIMR = 0x26922A09
+;SDTIMR2 = 0x4414C722
+;SDRCR = 0x00000498
+;CLK2XSRC = 0x00000000
+
+; This section can be used to configure the PLL1 and the EMIF3a registers
+; for starting the DDR2 interface on DSP-boot D800K002 devices.
+;            |------24|------16|-------8|-------0|
+; DDRPHYC1R: |             DDRPHYC1R             |
+; SDCR:      |              SDCR                 |
+; SDTIMR:    |              SDTIMR               |
+; SDTIMR2:   |              SDTIMR2              |
+; SDRCR:     |              SDRCR                |
+; CLK2XSRC:  |             CLK2XSRC              |
+;[DSP_EMIF3DDR_PATCHFXN]
+;DDRPHYC1R = 0x000000C4
+;SDCR = 0x08134632
+;SDTIMR = 0x26922A09
+;SDTIMR2 = 0x0014C722
+;SDRCR = 0x00000492
+;CLK2XSRC = 0x00000000
+
+;[INPUTFILE]
+;FILENAME=u-boot.bin
+;LOADADDRESS=0xC1080000
+;ENTRYPOINTADDRESS=0xC1080000
diff --git a/board/Barix/ipam390/ipam390.c b/board/Barix/ipam390/ipam390.c
new file mode 100644
index 0000000..f3f276e
--- /dev/null
+++ b/board/Barix/ipam390/ipam390.c
@@ -0,0 +1,348 @@
+/*
+ * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ * Based on:
+ * U-Boot:board/davinci/da8xxevm/da850evm.c
+ *
+ * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Based on da830evm.c. Original Copyrights follow:
+ *
+ * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <net.h>
+#include <netdev.h>
+#include <spi.h>
+#include <spi_flash.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/emif_defs.h>
+#include <asm/arch/emac_defs.h>
+#include <asm/arch/pinmux_defs.h>
+#include <asm/io.h>
+#include <asm/arch/davinci_misc.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <hwconfig.h>
+#include <bootstage.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
+#define HAS_RMII 1
+#else
+#define HAS_RMII 0
+#endif
+#endif /* CONFIG_DRIVER_TI_EMAC */
+
+void dsp_lpsc_on(unsigned domain, unsigned int id)
+{
+	dv_reg_p mdstat, mdctl, ptstat, ptcmd;
+	struct davinci_psc_regs *psc_regs;
+
+	psc_regs = davinci_psc0_regs;
+	mdstat = &psc_regs->psc0.mdstat[id];
+	mdctl = &psc_regs->psc0.mdctl[id];
+	ptstat = &psc_regs->ptstat;
+	ptcmd = &psc_regs->ptcmd;
+
+	while (*ptstat & (0x1 << domain))
+		;
+
+	if ((*mdstat & 0x1f) == 0x03)
+		return;                 /* Already on and enabled */
+
+	*mdctl |= 0x03;
+
+	*ptcmd = 0x1 << domain;
+
+	while (*ptstat & (0x1 << domain))
+		;
+	while ((*mdstat & 0x1f) != 0x03)
+		;		/* Probably an overkill... */
+}
+
+static void dspwake(void)
+{
+	unsigned *resetvect = (unsigned *)DAVINCI_L3CBARAM_BASE;
+	u32 val;
+
+	/* if the device is ARM only, return */
+	if ((readl(CHIP_REV_ID_REG) & 0x3f) == 0x10)
+		return;
+
+	if (hwconfig_subarg_cmp_f("dsp", "wake", "no", NULL))
+		return;
+
+	*resetvect++ = 0x1E000; /* DSP Idle */
+	/* clear out the next 10 words as NOP */
+	memset(resetvect, 0, sizeof(unsigned) * 10);
+
+	/* setup the DSP reset vector */
+	writel(DAVINCI_L3CBARAM_BASE, HOST1CFG);
+
+	dsp_lpsc_on(1, DAVINCI_LPSC_GEM);
+	val = readl(PSC0_MDCTL + (15 * 4));
+	val |= 0x100;
+	writel(val, (PSC0_MDCTL + (15 * 4)));
+}
+
+int misc_init_r(void)
+{
+	dspwake();
+	return 0;
+}
+
+static const struct pinmux_config gpio_pins[] = {
+	/* GP7[14] selects bootmode*/
+	{ pinmux(16), 8, 3 },	/* GP7[14] */
+};
+
+const struct pinmux_resource pinmuxes[] = {
+#ifdef CONFIG_DRIVER_TI_EMAC
+	PINMUX_ITEM(emac_pins_mdio),
+#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
+	PINMUX_ITEM(emac_pins_rmii),
+#else
+	PINMUX_ITEM(emac_pins_mii),
+#endif
+#endif
+	PINMUX_ITEM(uart2_pins_txrx),
+	PINMUX_ITEM(uart2_pins_rtscts),
+	PINMUX_ITEM(uart0_pins_txrx),
+	PINMUX_ITEM(uart0_pins_rtscts),
+#ifdef CONFIG_NAND_DAVINCI
+	PINMUX_ITEM(emifa_pins_cs3),
+	PINMUX_ITEM(emifa_pins_nand),
+#endif
+	PINMUX_ITEM(gpio_pins),
+};
+
+const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
+
+const struct lpsc_resource lpsc[] = {
+	{ DAVINCI_LPSC_AEMIF },	/* NAND, NOR */
+	{ DAVINCI_LPSC_EMAC },	/* image download */
+	{ DAVINCI_LPSC_UART2 },	/* console */
+	{ DAVINCI_LPSC_UART0 },	/* console */
+	{ DAVINCI_LPSC_GPIO },
+};
+
+const int lpsc_size = ARRAY_SIZE(lpsc);
+
+#ifndef CONFIG_DA850_EVM_MAX_CPU_CLK
+#define CONFIG_DA850_EVM_MAX_CPU_CLK	300000000
+#endif
+
+#define REV_AM18X_EVM		0x100
+
+/*
+ * get_board_rev() - setup to pass kernel board revision information
+ * Returns:
+ * bit[0-3]	Maximum cpu clock rate supported by onboard SoC
+ *		0000b - 300 MHz
+ *		0001b - 372 MHz
+ *		0010b - 408 MHz
+ *		0011b - 456 MHz
+ */
+u32 get_board_rev(void)
+{
+	char *s;
+	u32 maxcpuclk = CONFIG_DA850_EVM_MAX_CPU_CLK;
+	u32 rev = 0;
+
+	s = getenv("maxcpuclk");
+	if (s)
+		maxcpuclk = simple_strtoul(s, NULL, 10);
+
+	if (maxcpuclk >= 456000000)
+		rev = 3;
+	else if (maxcpuclk >= 408000000)
+		rev = 2;
+	else if (maxcpuclk >= 372000000)
+		rev = 1;
+#ifdef CONFIG_DA850_AM18X_EVM
+	rev |= REV_AM18X_EVM;
+#endif
+	return rev;
+}
+
+int board_early_init_f(void)
+{
+	/*
+	 * Power on required peripherals
+	 * ARM does not have access by default to PSC0 and PSC1
+	 * assuming here that the DSP bootloader has set the IOPU
+	 * such that PSC access is available to ARM
+	 */
+	if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
+		return 1;
+
+	return 0;
+}
+
+int board_init(void)
+{
+#ifndef CONFIG_USE_IRQ
+	irq_init();
+#endif
+
+	/* arch number of the board */
+	gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
+
+	/* setup the SUSPSRC for ARM to control emulation suspend */
+	writel(readl(&davinci_syscfg_regs->suspsrc) &
+	       ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
+		 DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
+		 DAVINCI_SYSCFG_SUSPSRC_UART0),
+	       &davinci_syscfg_regs->suspsrc);
+
+	/* configure pinmux settings */
+	if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
+		return 1;
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+	davinci_emac_mii_mode_sel(HAS_RMII);
+#endif /* CONFIG_DRIVER_TI_EMAC */
+
+	/* enable the console UART */
+	writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
+		DAVINCI_UART_PWREMU_MGMT_UTRST),
+#if (CONFIG_SYS_NS16550_COM1 == DAVINCI_UART0_BASE)
+	       &davinci_uart0_ctrl_regs->pwremu_mgmt);
+#else
+	       &davinci_uart2_ctrl_regs->pwremu_mgmt);
+#endif
+	return 0;
+}
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+/*
+ * Initializes on-board ethernet controllers.
+ */
+int board_eth_init(bd_t *bis)
+{
+	if (!davinci_emac_initialize()) {
+		printf("Error: Ethernet init failed!\n");
+		return -1;
+	}
+
+	return 0;
+}
+#endif /* CONFIG_DRIVER_TI_EMAC */
+
+static int init_led(int gpio, char *name, int val)
+{
+	int ret;
+
+	ret = gpio_request(gpio, name);
+	if (ret)
+		return -1;
+	ret = gpio_direction_output(gpio, val);
+	if (ret)
+		return -1;
+
+	return gpio;
+}
+
+#define LED_ON	0
+#define LED_OFF	1
+
+#if !defined(CONFIG_SPL_BUILD)
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void show_boot_progress(int status)
+{
+	static int red;
+	static int green;
+
+	if (red == 0)
+		red = init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF);
+	if (red != CONFIG_IPAM390_GPIO_LED_RED)
+		return;
+	if (green == 0)
+		green = init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green",
+				 LED_OFF);
+	if (green != CONFIG_IPAM390_GPIO_LED_GREEN)
+		return;
+
+	switch (status) {
+	case BOOTSTAGE_ID_RUN_OS:
+		/*
+		 * set normal state
+		 * LED Red  : off
+		 * LED green: off
+		 */
+		gpio_set_value(red, LED_OFF);
+		gpio_set_value(green, LED_OFF);
+		break;
+	case BOOTSTAGE_ID_MAIN_LOOP:
+		/*
+		 * U-Boot operation
+		 * LED Red  : on
+		 * LED green: on
+		 */
+		gpio_set_value(red, LED_ON);
+		gpio_set_value(green, LED_ON);
+		break;
+	}
+}
+#endif
+#endif
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+	int ret;
+	int bootmode = 0;
+
+	/*
+	 * GP7[14] selects bootmode:
+	 * 1: boot linux
+	 * 0: boot u-boot
+	 * if error accessing gpio boot U-Boot
+	 *
+	 * SPL bootmode
+	 * 0: boot linux
+	 * 1: boot u-boot
+	 */
+	ret = gpio_request(CONFIG_IPAM390_GPIO_BOOTMODE , "bootmode");
+	if (ret)
+		bootmode = 1;
+	if (!bootmode) {
+		ret = gpio_direction_input(CONFIG_IPAM390_GPIO_BOOTMODE);
+		if (ret)
+			bootmode = 1;
+	}
+	if (!bootmode)
+		ret = gpio_get_value(CONFIG_IPAM390_GPIO_BOOTMODE);
+	if (!bootmode)
+		if (ret == 0)
+			bootmode = 1;
+	if (bootmode) {
+		/*
+		 * Booting U-Boot
+		 * LED Red  : on
+		 * LED green: off
+		 */
+		init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
+		init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
+	} else {
+		/*
+		 * Booting Linux
+		 * LED Red  : off
+		 * LED green: off
+		 */
+		init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF);
+		init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
+	}
+	return bootmode;
+}
+#endif
diff --git a/board/Barix/ipam390/u-boot-spl-ipam390.lds b/board/Barix/ipam390/u-boot-spl-ipam390.lds
new file mode 100644
index 0000000..5480d1f
--- /dev/null
+++ b/board/Barix/ipam390/u-boot-spl-ipam390.lds
@@ -0,0 +1,53 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * (C) Copyright 2008
+ * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE,\
+		LENGTH = CONFIG_SPL_MAX_FOOTPRINT }
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	__start = .;
+	  arch/arm/cpu/arm926ejs/start.o	(.text*)
+	  *(.text*)
+	} >.sram
+
+	. = ALIGN(4);
+	.rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram
+
+	. = ALIGN(4);
+	.data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
+
+	. = ALIGN(4);
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	} >.sram
+
+	.bss :
+	{
+		. = ALIGN(4);
+		__bss_start = .;
+		*(.bss*)
+		. = ALIGN(4);
+		__bss_end = .;
+	} >.sram
+
+	__image_copy_end = .;
+	_end = .;
+}
diff --git a/board/altera/socfpga_cyclone5/Makefile b/board/altera/socfpga/Makefile
index 101fc7c..101fc7c 100644
--- a/board/altera/socfpga_cyclone5/Makefile
+++ b/board/altera/socfpga/Makefile
diff --git a/board/altera/socfpga_cyclone5/socfpga_cyclone5.c b/board/altera/socfpga/socfpga_cyclone5.c
index 576066b..576066b 100644
--- a/board/altera/socfpga_cyclone5/socfpga_cyclone5.c
+++ b/board/altera/socfpga/socfpga_cyclone5.c
diff --git a/board/freescale/mx6qsabrelite/README b/board/boundary/nitrogen6x/README.mx6qsabrelite
index 12a9c85..12a9c85 100644
--- a/board/freescale/mx6qsabrelite/README
+++ b/board/boundary/nitrogen6x/README.mx6qsabrelite
diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c
index 1a29b6f..79ab449 100644
--- a/board/boundary/nitrogen6x/nitrogen6x.c
+++ b/board/boundary/nitrogen6x/nitrogen6x.c
@@ -461,25 +461,12 @@ struct display_info_t {
 static int detect_hdmi(struct display_info_t const *dev)
 {
 	struct hdmi_regs *hdmi	= (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-	return readb(&hdmi->phy_stat0) & HDMI_PHY_HPD;
+	return readb(&hdmi->phy_stat0) & HDMI_DVI_STAT;
 }
 
-static void enable_hdmi(struct display_info_t const *dev)
+static void do_enable_hdmi(struct display_info_t const *dev)
 {
-	struct hdmi_regs *hdmi	= (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-	u8 reg;
-	printf("%s: setup HDMI monitor\n", __func__);
-	reg = readb(&hdmi->phy_conf0);
-	reg |= HDMI_PHY_CONF0_PDZ_MASK;
-	writeb(reg, &hdmi->phy_conf0);
-
-	udelay(3000);
-	reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
-	writeb(reg, &hdmi->phy_conf0);
-	udelay(3000);
-	reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
-	writeb(reg, &hdmi->phy_conf0);
-	writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
+	imx_enable_hdmi_phy();
 }
 
 static int detect_i2c(struct display_info_t const *dev)
@@ -512,7 +499,7 @@ static struct display_info_t const displays[] = {{
 	.addr	= 0,
 	.pixfmt	= IPU_PIX_FMT_RGB24,
 	.detect	= detect_hdmi,
-	.enable	= enable_hdmi,
+	.enable	= do_enable_hdmi,
 	.mode	= {
 		.name           = "HDMI",
 		.refresh        = 60,
@@ -637,25 +624,15 @@ static void setup_display(void)
 	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 	struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
 	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
-	struct hdmi_regs *hdmi	= (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-
 	int reg;
 
+	enable_ipu_clock();
+	imx_setup_hdmi();
 	/* Turn on LDB0,IPU,IPU DI0 clocks */
 	reg = __raw_readl(&mxc_ccm->CCGR3);
-	reg |=   MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET
-		|MXC_CCM_CCGR3_LDB_DI0_MASK;
+	reg |=  MXC_CCM_CCGR3_LDB_DI0_MASK;
 	writel(reg, &mxc_ccm->CCGR3);
 
-	/* Turn on HDMI PHY clock */
-	reg = __raw_readl(&mxc_ccm->CCGR2);
-	reg |=  MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK
-	       |MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
-	writel(reg, &mxc_ccm->CCGR2);
-
-	/* clear HDMI PHY reset */
-	writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
-
 	/* set PFD1_FRAC to 0x13 == 455 MHz (480*18)/0x13 */
 	writel(ANATOP_PFD_480_PFD1_FRAC_MASK, &anatop->pfd_480_clr);
 	writel(0x13<<ANATOP_PFD_480_PFD1_FRAC_SHIFT, &anatop->pfd_480_set);
@@ -673,15 +650,8 @@ static void setup_display(void)
 	writel(reg, &mxc_ccm->cscmr2);
 
 	reg = readl(&mxc_ccm->chsccdr);
-	reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK
-		|MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK
-		|MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
 	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
-		<<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)
-	      |(CHSCCDR_PODF_DIVIDE_BY_3
-		<<MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
-	      |(CHSCCDR_IPU_PRE_CLK_540M_PFD
-		<<MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+		<<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
 	writel(reg, &mxc_ccm->chsccdr);
 
 	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
diff --git a/board/davinci/da8xxevm/da850evm.c b/board/davinci/da8xxevm/da850evm.c
index 01745b2..85b4830 100644
--- a/board/davinci/da8xxevm/da850evm.c
+++ b/board/davinci/da8xxevm/da850evm.c
@@ -323,10 +323,6 @@ int board_early_init_f(void)
 
 int board_init(void)
 {
-#if defined(CONFIG_USE_NOR) || defined(CONFIG_DAVINCI_MMC)
-	u32 val;
-#endif
-
 #ifndef CONFIG_USE_IRQ
 	irq_init();
 #endif
@@ -366,12 +362,10 @@ int board_init(void)
 
 #ifdef CONFIG_USE_NOR
 	/* Set the GPIO direction as output */
-	clrbits_be32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));
+	clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));
 
 	/* Set the output as low */
-	val = readl(GPIO_BANK0_REG_SET_ADDR);
-	val |= (0x01 << 11);
-	writel(val, GPIO_BANK0_REG_CLR_ADDR);
+	writel(0x01 << 11, GPIO_BANK0_REG_CLR_ADDR);
 #endif
 
 #ifdef CONFIG_DAVINCI_MMC
@@ -379,9 +373,7 @@ int board_init(void)
 	clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));
 
 	/* Set the output as high */
-	val = readl(GPIO_BANK0_REG_SET_ADDR);
-	val |= (0x01 << 11);
-	writel(val, GPIO_BANK0_REG_SET_ADDR);
+	writel(0x01 << 11, GPIO_BANK0_REG_SET_ADDR);
 #endif
 
 #ifdef CONFIG_DRIVER_TI_EMAC
diff --git a/board/freescale/mx6qsabrelite/Makefile b/board/freescale/mx6qsabrelite/Makefile
deleted file mode 100644
index 141437c..0000000
--- a/board/freescale/mx6qsabrelite/Makefile
+++ /dev/null
@@ -1,28 +0,0 @@
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
-#
-# (C) Copyright 2011 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-include $(TOPDIR)/config.mk
-
-LIB    = $(obj)lib$(BOARD).o
-
-COBJS  := mx6qsabrelite.o
-
-SRCS   := $(COBJS:.o=.c)
-OBJS   := $(addprefix $(obj),$(COBJS))
-
-$(LIB):        $(obj).depend $(OBJS)
-	$(call cmd_link_o_target, $(OBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
deleted file mode 100644
index 78451e6..0000000
--- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
+++ /dev/null
@@ -1,832 +0,0 @@
-/*
- * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+ 
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6q_pins.h>
-#include <asm/errno.h>
-#include <asm/gpio.h>
-#include <asm/imx-common/iomux-v3.h>
-#include <asm/imx-common/mxc_i2c.h>
-#include <asm/imx-common/boot_mode.h>
-#include <mmc.h>
-#include <fsl_esdhc.h>
-#include <malloc.h>
-#include <micrel.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <linux/fb.h>
-#include <ipu_pixfmt.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/mxc_hdmi.h>
-#include <i2c.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
-	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
-	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
-	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED |		\
-	PAD_CTL_DSE_40ohm     | PAD_CTL_SRE_FAST)
-
-#define BUTTON_PAD_CTRL (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define I2C_PAD_CTRL	(PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
-	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
-
-	return 0;
-}
-
-iomux_v3_cfg_t const uart1_pads[] = {
-	MX6_PAD_SD3_DAT6__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_SD3_DAT7__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart2_pads[] = {
-	MX6_PAD_EIM_D26__UART2_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_EIM_D27__UART2_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-/* I2C1, SGTL5000 */
-struct i2c_pads_info i2c_pad_info0 = {
-	.scl = {
-		.i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC,
-		.gpio_mode = MX6_PAD_EIM_D21__GPIO_3_21 | PC,
-		.gp = IMX_GPIO_NR(3, 21)
-	},
-	.sda = {
-		.i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC,
-		.gpio_mode = MX6_PAD_EIM_D28__GPIO_3_28 | PC,
-		.gp = IMX_GPIO_NR(3, 28)
-	}
-};
-
-/* I2C2 Camera, MIPI */
-struct i2c_pads_info i2c_pad_info1 = {
-	.scl = {
-		.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC,
-		.gpio_mode = MX6_PAD_KEY_COL3__GPIO_4_12 | PC,
-		.gp = IMX_GPIO_NR(4, 12)
-	},
-	.sda = {
-		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
-		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO_4_13 | PC,
-		.gp = IMX_GPIO_NR(4, 13)
-	}
-};
-
-/* I2C3, J15 - RGB connector */
-struct i2c_pads_info i2c_pad_info2 = {
-	.scl = {
-		.i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC,
-		.gpio_mode = MX6_PAD_GPIO_5__GPIO_1_5 | PC,
-		.gp = IMX_GPIO_NR(1, 5)
-	},
-	.sda = {
-		.i2c_mode = MX6_PAD_GPIO_16__I2C3_SDA | PC,
-		.gpio_mode = MX6_PAD_GPIO_16__GPIO_7_11 | PC,
-		.gp = IMX_GPIO_NR(7, 11)
-	}
-};
-
-iomux_v3_cfg_t const usdhc3_pads[] = {
-	MX6_PAD_SD3_CLK__USDHC3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_CMD__USDHC3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT5__GPIO_7_0    | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-iomux_v3_cfg_t const usdhc4_pads[] = {
-	MX6_PAD_SD4_CLK__USDHC4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_CMD__USDHC4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT0__USDHC4_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT1__USDHC4_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT2__USDHC4_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT3__USDHC4_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_NANDF_D6__GPIO_2_6    | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-iomux_v3_cfg_t const enet_pads1[] = {
-	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TXC__ENET_RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD0__ENET_RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD1__ENET_RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD2__ENET_RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD3__ENET_RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	/* pin 35 - 1 (PHY_AD2) on reset */
-	MX6_PAD_RGMII_RXC__GPIO_6_30		| MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* pin 32 - 1 - (MODE0) all */
-	MX6_PAD_RGMII_RD0__GPIO_6_25		| MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* pin 31 - 1 - (MODE1) all */
-	MX6_PAD_RGMII_RD1__GPIO_6_27		| MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* pin 28 - 1 - (MODE2) all */
-	MX6_PAD_RGMII_RD2__GPIO_6_28		| MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* pin 27 - 1 - (MODE3) all */
-	MX6_PAD_RGMII_RD3__GPIO_6_29		| MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
-	MX6_PAD_RGMII_RX_CTL__GPIO_6_24	| MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* pin 42 PHY nRST */
-	MX6_PAD_EIM_D23__GPIO_3_23		| MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const enet_pads2[] = {
-	MX6_PAD_RGMII_RXC__ENET_RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD0__ENET_RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD1__ENET_RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD2__ENET_RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD3__ENET_RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-/* Button assignments for J14 */
-static iomux_v3_cfg_t const button_pads[] = {
-	/* Menu */
-	MX6_PAD_NANDF_D1__GPIO_2_1	| MUX_PAD_CTRL(BUTTON_PAD_CTRL),
-	/* Back */
-	MX6_PAD_NANDF_D2__GPIO_2_2	| MUX_PAD_CTRL(BUTTON_PAD_CTRL),
-	/* Labelled Search (mapped to Power under Android) */
-	MX6_PAD_NANDF_D3__GPIO_2_3	| MUX_PAD_CTRL(BUTTON_PAD_CTRL),
-	/* Home */
-	MX6_PAD_NANDF_D4__GPIO_2_4	| MUX_PAD_CTRL(BUTTON_PAD_CTRL),
-	/* Volume Down */
-	MX6_PAD_GPIO_19__GPIO_4_5	| MUX_PAD_CTRL(BUTTON_PAD_CTRL),
-	/* Volume Up */
-	MX6_PAD_GPIO_18__GPIO_7_13	| MUX_PAD_CTRL(BUTTON_PAD_CTRL),
-};
-
-static void setup_iomux_enet(void)
-{
-	gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
-	gpio_direction_output(IMX_GPIO_NR(6, 30), 1);
-	gpio_direction_output(IMX_GPIO_NR(6, 25), 1);
-	gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
-	gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
-	gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
-	imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
-	gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
-
-	/* Need delay 10ms according to KSZ9021 spec */
-	udelay(1000 * 10);
-	gpio_set_value(IMX_GPIO_NR(3, 23), 1);
-
-	imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
-}
-
-iomux_v3_cfg_t const usb_pads[] = {
-	MX6_PAD_GPIO_17__GPIO_7_12 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_iomux_uart(void)
-{
-	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-	imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
-}
-
-#ifdef CONFIG_USB_EHCI_MX6
-int board_ehci_hcd_init(int port)
-{
-	imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads));
-
-	/* Reset USB hub */
-	gpio_direction_output(IMX_GPIO_NR(7, 12), 0);
-	mdelay(2);
-	gpio_set_value(IMX_GPIO_NR(7, 12), 1);
-
-	return 0;
-}
-#endif
-
-#ifdef CONFIG_FSL_ESDHC
-struct fsl_esdhc_cfg usdhc_cfg[2] = {
-	{USDHC3_BASE_ADDR},
-	{USDHC4_BASE_ADDR},
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-	int ret;
-
-	if (cfg->esdhc_base == USDHC3_BASE_ADDR) {
-		gpio_direction_input(IMX_GPIO_NR(7, 0));
-		ret = !gpio_get_value(IMX_GPIO_NR(7, 0));
-	} else {
-		gpio_direction_input(IMX_GPIO_NR(2, 6));
-		ret = !gpio_get_value(IMX_GPIO_NR(2, 6));
-	}
-
-	return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-	s32 status = 0;
-	u32 index = 0;
-
-	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-
-	usdhc_cfg[0].max_bus_width = 4;
-	usdhc_cfg[1].max_bus_width = 4;
-
-	for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
-		switch (index) {
-		case 0:
-			imx_iomux_v3_setup_multiple_pads(
-				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
-			break;
-		case 1:
-			imx_iomux_v3_setup_multiple_pads(
-				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
-		       break;
-	       default:
-			printf("Warning: you configured more USDHC controllers"
-			       "(%d) then supported by the board (%d)\n",
-			       index + 1, CONFIG_SYS_FSL_USDHC_NUM);
-			return status;
-		}
-
-		status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
-	}
-
-	return status;
-}
-#endif
-
-#ifdef CONFIG_MXC_SPI
-iomux_v3_cfg_t const ecspi1_pads[] = {
-	/* SS1 */
-	MX6_PAD_EIM_D19__GPIO_3_19   | MUX_PAD_CTRL(SPI_PAD_CTRL),
-	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
-	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
-	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
-};
-
-void setup_spi(void)
-{
-	imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
-					 ARRAY_SIZE(ecspi1_pads));
-}
-#endif
-
-int board_phy_config(struct phy_device *phydev)
-{
-	/* min rx data delay */
-	ksz9021_phy_extended_write(phydev,
-			MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW, 0x0);
-	/* min tx data delay */
-	ksz9021_phy_extended_write(phydev,
-			MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW, 0x0);
-	/* max rx/tx clock delay, min rx/tx control */
-	ksz9021_phy_extended_write(phydev,
-			MII_KSZ9021_EXT_RGMII_CLOCK_SKEW, 0xf0f0);
-	if (phydev->drv->config)
-		phydev->drv->config(phydev);
-
-	return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
-	uint32_t base = IMX_FEC_BASE;
-	struct mii_dev *bus = NULL;
-	struct phy_device *phydev = NULL;
-	int ret;
-
-	setup_iomux_enet();
-
-#ifdef CONFIG_FEC_MXC
-	bus = fec_get_miibus(base, -1);
-	if (!bus)
-		return 0;
-	/* scan phy 4,5,6,7 */
-	phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII);
-	if (!phydev) {
-		free(bus);
-		return 0;
-	}
-	printf("using phy at %d\n", phydev->addr);
-	ret  = fec_probe(bis, -1, base, bus, phydev);
-	if (ret) {
-		printf("FEC MXC: %s:failed\n", __func__);
-		free(phydev);
-		free(bus);
-	}
-#endif
-	return 0;
-}
-
-static void setup_buttons(void)
-{
-	imx_iomux_v3_setup_multiple_pads(button_pads,
-					 ARRAY_SIZE(button_pads));
-}
-
-#ifdef CONFIG_CMD_SATA
-
-int setup_sata(void)
-{
-	struct iomuxc_base_regs *const iomuxc_regs
-		= (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR;
-	int ret = enable_sata_clock();
-	if (ret)
-		return ret;
-
-	clrsetbits_le32(&iomuxc_regs->gpr[13],
-			IOMUXC_GPR13_SATA_MASK,
-			IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB
-			|IOMUXC_GPR13_SATA_PHY_7_SATA2M
-			|IOMUXC_GPR13_SATA_SPEED_3G
-			|(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT)
-			|IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED
-			|IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16
-			|IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB
-			|IOMUXC_GPR13_SATA_PHY_2_TX_1P104V
-			|IOMUXC_GPR13_SATA_PHY_1_SLOW);
-
-	return 0;
-}
-#endif
-
-#if defined(CONFIG_VIDEO_IPUV3)
-
-static iomux_v3_cfg_t const backlight_pads[] = {
-	/* Backlight on RGB connector: J15 */
-	MX6_PAD_SD1_DAT3__GPIO_1_21 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#define RGB_BACKLIGHT_GP IMX_GPIO_NR(1, 21)
-
-	/* Backlight on LVDS connector: J6 */
-	MX6_PAD_SD1_CMD__GPIO_1_18 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 18)
-};
-
-static iomux_v3_cfg_t const rgb_pads[] = {
-	MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK,
-	MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15,
-	MX6_PAD_DI0_PIN2__IPU1_DI0_PIN2,
-	MX6_PAD_DI0_PIN3__IPU1_DI0_PIN3,
-	MX6_PAD_DI0_PIN4__GPIO_4_20,
-	MX6_PAD_DISP0_DAT0__IPU1_DISP0_DAT_0,
-	MX6_PAD_DISP0_DAT1__IPU1_DISP0_DAT_1,
-	MX6_PAD_DISP0_DAT2__IPU1_DISP0_DAT_2,
-	MX6_PAD_DISP0_DAT3__IPU1_DISP0_DAT_3,
-	MX6_PAD_DISP0_DAT4__IPU1_DISP0_DAT_4,
-	MX6_PAD_DISP0_DAT5__IPU1_DISP0_DAT_5,
-	MX6_PAD_DISP0_DAT6__IPU1_DISP0_DAT_6,
-	MX6_PAD_DISP0_DAT7__IPU1_DISP0_DAT_7,
-	MX6_PAD_DISP0_DAT8__IPU1_DISP0_DAT_8,
-	MX6_PAD_DISP0_DAT9__IPU1_DISP0_DAT_9,
-	MX6_PAD_DISP0_DAT10__IPU1_DISP0_DAT_10,
-	MX6_PAD_DISP0_DAT11__IPU1_DISP0_DAT_11,
-	MX6_PAD_DISP0_DAT12__IPU1_DISP0_DAT_12,
-	MX6_PAD_DISP0_DAT13__IPU1_DISP0_DAT_13,
-	MX6_PAD_DISP0_DAT14__IPU1_DISP0_DAT_14,
-	MX6_PAD_DISP0_DAT15__IPU1_DISP0_DAT_15,
-	MX6_PAD_DISP0_DAT16__IPU1_DISP0_DAT_16,
-	MX6_PAD_DISP0_DAT17__IPU1_DISP0_DAT_17,
-	MX6_PAD_DISP0_DAT18__IPU1_DISP0_DAT_18,
-	MX6_PAD_DISP0_DAT19__IPU1_DISP0_DAT_19,
-	MX6_PAD_DISP0_DAT20__IPU1_DISP0_DAT_20,
-	MX6_PAD_DISP0_DAT21__IPU1_DISP0_DAT_21,
-	MX6_PAD_DISP0_DAT22__IPU1_DISP0_DAT_22,
-	MX6_PAD_DISP0_DAT23__IPU1_DISP0_DAT_23,
-};
-
-struct display_info_t {
-	int	bus;
-	int	addr;
-	int	pixfmt;
-	int	(*detect)(struct display_info_t const *dev);
-	void	(*enable)(struct display_info_t const *dev);
-	struct	fb_videomode mode;
-};
-
-
-static int detect_hdmi(struct display_info_t const *dev)
-{
-	struct hdmi_regs *hdmi	= (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-	return readb(&hdmi->phy_stat0) & HDMI_PHY_HPD;
-}
-
-static void enable_hdmi(struct display_info_t const *dev)
-{
-	struct hdmi_regs *hdmi	= (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-	u8 reg;
-	printf("%s: setup HDMI monitor\n", __func__);
-	reg = readb(&hdmi->phy_conf0);
-	reg |= HDMI_PHY_CONF0_PDZ_MASK;
-	writeb(reg, &hdmi->phy_conf0);
-
-	udelay(3000);
-	reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
-	writeb(reg, &hdmi->phy_conf0);
-	udelay(3000);
-	reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
-	writeb(reg, &hdmi->phy_conf0);
-	writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
-}
-
-static int detect_i2c(struct display_info_t const *dev)
-{
-	return ((0 == i2c_set_bus_num(dev->bus))
-		&&
-		(0 == i2c_probe(dev->addr)));
-}
-
-static void enable_lvds(struct display_info_t const *dev)
-{
-	struct iomuxc *iomux = (struct iomuxc *)
-				IOMUXC_BASE_ADDR;
-	u32 reg = readl(&iomux->gpr[2]);
-	reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT;
-	writel(reg, &iomux->gpr[2]);
-	gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
-}
-
-static void enable_rgb(struct display_info_t const *dev)
-{
-	imx_iomux_v3_setup_multiple_pads(
-		rgb_pads,
-		 ARRAY_SIZE(rgb_pads));
-	gpio_direction_output(RGB_BACKLIGHT_GP, 1);
-}
-
-static struct display_info_t const displays[] = {{
-	.bus	= -1,
-	.addr	= 0,
-	.pixfmt	= IPU_PIX_FMT_RGB24,
-	.detect	= detect_hdmi,
-	.enable	= enable_hdmi,
-	.mode	= {
-		.name           = "HDMI",
-		.refresh        = 60,
-		.xres           = 1024,
-		.yres           = 768,
-		.pixclock       = 15385,
-		.left_margin    = 220,
-		.right_margin   = 40,
-		.upper_margin   = 21,
-		.lower_margin   = 7,
-		.hsync_len      = 60,
-		.vsync_len      = 10,
-		.sync           = FB_SYNC_EXT,
-		.vmode          = FB_VMODE_NONINTERLACED
-} }, {
-	.bus	= 2,
-	.addr	= 0x4,
-	.pixfmt	= IPU_PIX_FMT_LVDS666,
-	.detect	= detect_i2c,
-	.enable	= enable_lvds,
-	.mode	= {
-		.name           = "Hannstar-XGA",
-		.refresh        = 60,
-		.xres           = 1024,
-		.yres           = 768,
-		.pixclock       = 15385,
-		.left_margin    = 220,
-		.right_margin   = 40,
-		.upper_margin   = 21,
-		.lower_margin   = 7,
-		.hsync_len      = 60,
-		.vsync_len      = 10,
-		.sync           = FB_SYNC_EXT,
-		.vmode          = FB_VMODE_NONINTERLACED
-} }, {
-	.bus	= 2,
-	.addr	= 0x38,
-	.pixfmt	= IPU_PIX_FMT_LVDS666,
-	.detect	= detect_i2c,
-	.enable	= enable_lvds,
-	.mode	= {
-		.name           = "wsvga-lvds",
-		.refresh        = 60,
-		.xres           = 1024,
-		.yres           = 600,
-		.pixclock       = 15385,
-		.left_margin    = 220,
-		.right_margin   = 40,
-		.upper_margin   = 21,
-		.lower_margin   = 7,
-		.hsync_len      = 60,
-		.vsync_len      = 10,
-		.sync           = FB_SYNC_EXT,
-		.vmode          = FB_VMODE_NONINTERLACED
-} }, {
-	.bus	= 2,
-	.addr	= 0x48,
-	.pixfmt	= IPU_PIX_FMT_RGB666,
-	.detect	= detect_i2c,
-	.enable	= enable_rgb,
-	.mode	= {
-		.name           = "wvga-rgb",
-		.refresh        = 57,
-		.xres           = 800,
-		.yres           = 480,
-		.pixclock       = 37037,
-		.left_margin    = 40,
-		.right_margin   = 60,
-		.upper_margin   = 10,
-		.lower_margin   = 10,
-		.hsync_len      = 20,
-		.vsync_len      = 10,
-		.sync           = 0,
-		.vmode          = FB_VMODE_NONINTERLACED
-} } };
-
-int board_video_skip(void)
-{
-	int i;
-	int ret;
-	char const *panel = getenv("panel");
-	if (!panel) {
-		for (i = 0; i < ARRAY_SIZE(displays); i++) {
-			struct display_info_t const *dev = displays+i;
-			if (dev->detect(dev)) {
-				panel = dev->mode.name;
-				printf("auto-detected panel %s\n", panel);
-				break;
-			}
-		}
-		if (!panel) {
-			panel = displays[0].mode.name;
-			printf("No panel detected: default to %s\n", panel);
-		}
-	} else {
-		for (i = 0; i < ARRAY_SIZE(displays); i++) {
-			if (!strcmp(panel, displays[i].mode.name))
-				break;
-		}
-	}
-	if (i < ARRAY_SIZE(displays)) {
-		ret = ipuv3_fb_init(&displays[i].mode, 0,
-				    displays[i].pixfmt);
-		if (!ret) {
-			displays[i].enable(displays+i);
-			printf("Display: %s (%ux%u)\n",
-			       displays[i].mode.name,
-			       displays[i].mode.xres,
-			       displays[i].mode.yres);
-		} else
-			printf("LCD %s cannot be configured: %d\n",
-			       displays[i].mode.name, ret);
-	} else {
-		printf("unsupported panel %s\n", panel);
-		ret = -EINVAL;
-	}
-	return (0 != ret);
-}
-
-static void setup_display(void)
-{
-	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-	struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
-	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
-	struct hdmi_regs *hdmi	= (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-
-	int reg;
-
-	/* Turn on LDB0,IPU,IPU DI0 clocks */
-	reg = __raw_readl(&mxc_ccm->CCGR3);
-	reg |=   MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET
-		|MXC_CCM_CCGR3_LDB_DI0_MASK;
-	writel(reg, &mxc_ccm->CCGR3);
-
-	/* Turn on HDMI PHY clock */
-	reg = __raw_readl(&mxc_ccm->CCGR2);
-	reg |=  MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK
-	       |MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
-	writel(reg, &mxc_ccm->CCGR2);
-
-	/* clear HDMI PHY reset */
-	writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
-
-	/* set PFD1_FRAC to 0x13 == 455 MHz (480*18)/0x13 */
-	writel(ANATOP_PFD_480_PFD1_FRAC_MASK, &anatop->pfd_480_clr);
-	writel(0x13<<ANATOP_PFD_480_PFD1_FRAC_SHIFT, &anatop->pfd_480_set);
-
-	/* set LDB0, LDB1 clk select to 011/011 */
-	reg = readl(&mxc_ccm->cs2cdr);
-	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
-		 |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
-	reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
-	      |(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
-	writel(reg, &mxc_ccm->cs2cdr);
-
-	reg = readl(&mxc_ccm->cscmr2);
-	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
-	writel(reg, &mxc_ccm->cscmr2);
-
-	reg = readl(&mxc_ccm->chsccdr);
-	reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK
-		|MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK
-		|MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
-	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
-		<<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)
-	      |(CHSCCDR_PODF_DIVIDE_BY_3
-		<<MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
-	      |(CHSCCDR_IPU_PRE_CLK_540M_PFD
-		<<MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
-	writel(reg, &mxc_ccm->chsccdr);
-
-	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
-	     |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
-	     |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
-	     |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
-	     |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT
-	     |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
-	     |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT
-	     |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
-	     |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
-	writel(reg, &iomux->gpr[2]);
-
-	reg = readl(&iomux->gpr[3]);
-	reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
-	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
-	       <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
-	writel(reg, &iomux->gpr[3]);
-
-	/* backlights off until needed */
-	imx_iomux_v3_setup_multiple_pads(backlight_pads,
-					 ARRAY_SIZE(backlight_pads));
-	gpio_direction_input(LVDS_BACKLIGHT_GP);
-	gpio_direction_input(RGB_BACKLIGHT_GP);
-}
-#endif
-
-int board_early_init_f(void)
-{
-	setup_iomux_uart();
-	setup_buttons();
-
-#if defined(CONFIG_VIDEO_IPUV3)
-	setup_display();
-#endif
-	return 0;
-}
-
-/*
- * Do not overwrite the console
- * Use always serial for U-Boot console
- */
-int overwrite_console(void)
-{
-	return 1;
-}
-
-int board_init(void)
-{
-	/* address of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
-#ifdef CONFIG_MXC_SPI
-	setup_spi();
-#endif
-	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
-	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
-	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
-
-#ifdef CONFIG_CMD_SATA
-	setup_sata();
-#endif
-
-	return 0;
-}
-
-int checkboard(void)
-{
-	puts("Board: MX6Q-Sabre Lite\n");
-
-	return 0;
-}
-
-struct button_key {
-	char const	*name;
-	unsigned	gpnum;
-	char		ident;
-};
-
-static struct button_key const buttons[] = {
-	{"back",	IMX_GPIO_NR(2, 2),	'B'},
-	{"home",	IMX_GPIO_NR(2, 4),	'H'},
-	{"menu",	IMX_GPIO_NR(2, 1),	'M'},
-	{"search",	IMX_GPIO_NR(2, 3),	'S'},
-	{"volup",	IMX_GPIO_NR(7, 13),	'V'},
-	{"voldown",	IMX_GPIO_NR(4, 5),	'v'},
-};
-
-/*
- * generate a null-terminated string containing the buttons pressed
- * returns number of keys pressed
- */
-static int read_keys(char *buf)
-{
-	int i, numpressed = 0;
-	for (i = 0; i < ARRAY_SIZE(buttons); i++) {
-		if (!gpio_get_value(buttons[i].gpnum))
-			buf[numpressed++] = buttons[i].ident;
-	}
-	buf[numpressed] = '\0';
-	return numpressed;
-}
-
-static int do_kbd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	char envvalue[ARRAY_SIZE(buttons)+1];
-	int numpressed = read_keys(envvalue);
-	setenv("keybd", envvalue);
-	return numpressed == 0;
-}
-
-U_BOOT_CMD(
-	kbd, 1, 1, do_kbd,
-	"Tests for keypresses, sets 'keybd' environment variable",
-	"Returns 0 (true) to shell if key is pressed."
-);
-
-#ifdef CONFIG_PREBOOT
-static char const kbd_magic_prefix[] = "key_magic";
-static char const kbd_command_prefix[] = "key_cmd";
-
-static void preboot_keys(void)
-{
-	int numpressed;
-	char keypress[ARRAY_SIZE(buttons)+1];
-	numpressed = read_keys(keypress);
-	if (numpressed) {
-		char *kbd_magic_keys = getenv("magic_keys");
-		char *suffix;
-		/*
-		 * loop over all magic keys
-		 */
-		for (suffix = kbd_magic_keys; *suffix; ++suffix) {
-			char *keys;
-			char magic[sizeof(kbd_magic_prefix) + 1];
-			sprintf(magic, "%s%c", kbd_magic_prefix, *suffix);
-			keys = getenv(magic);
-			if (keys) {
-				if (!strcmp(keys, keypress))
-					break;
-			}
-		}
-		if (*suffix) {
-			char cmd_name[sizeof(kbd_command_prefix) + 1];
-			char *cmd;
-			sprintf(cmd_name, "%s%c", kbd_command_prefix, *suffix);
-			cmd = getenv(cmd_name);
-			if (cmd) {
-				setenv("preboot", cmd);
-				return;
-			}
-		}
-	}
-}
-#endif
-
-#ifdef CONFIG_CMD_BMODE
-static const struct boot_mode board_boot_modes[] = {
-	/* 4 bit bus width */
-	{"mmc0",	MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
-	{"mmc1",	MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
-	{NULL,		0},
-};
-#endif
-
-int misc_init_r(void)
-{
-#ifdef CONFIG_PREBOOT
-	preboot_keys();
-#endif
-
-#ifdef CONFIG_CMD_BMODE
-	add_board_boot_modes(board_boot_modes);
-#endif
-	return 0;
-}
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 936f029..5db516d 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -18,7 +18,12 @@
 #include <fsl_esdhc.h>
 #include <miiphy.h>
 #include <netdev.h>
-
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
 DECLARE_GLOBAL_DATA_PTR;
 
 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
@@ -228,6 +233,60 @@ int board_phy_config(struct phy_device *phydev)
 	return 0;
 }
 
+#if defined(CONFIG_VIDEO_IPUV3)
+static struct fb_videomode const hdmi = {
+	.name           = "HDMI",
+	.refresh        = 60,
+	.xres           = 1024,
+	.yres           = 768,
+	.pixclock       = 15385,
+	.left_margin    = 220,
+	.right_margin   = 40,
+	.upper_margin   = 21,
+	.lower_margin   = 7,
+	.hsync_len      = 60,
+	.vsync_len      = 10,
+	.sync           = FB_SYNC_EXT,
+	.vmode          = FB_VMODE_NONINTERLACED
+};
+
+int board_video_skip(void)
+{
+	int ret;
+
+	ret = ipuv3_fb_init(&hdmi, 0, IPU_PIX_FMT_RGB24);
+
+	if (ret)
+		printf("HDMI cannot be configured: %d\n", ret);
+
+	imx_enable_hdmi_phy();
+	return ret;
+}
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+
+	reg = readl(&mxc_ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->chsccdr);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
 int board_eth_init(bd_t *bis)
 {
 	int ret;
@@ -244,6 +303,9 @@ int board_eth_init(bd_t *bis)
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
+#if defined(CONFIG_VIDEO_IPUV3)
+	setup_display();
+#endif
 
 	return 0;
 }
diff --git a/board/highbank/highbank.c b/board/highbank/highbank.c
index 8cdcea8..4b272c7 100644
--- a/board/highbank/highbank.c
+++ b/board/highbank/highbank.c
@@ -12,13 +12,21 @@
 #include <asm/sizes.h>
 #include <asm/io.h>
 
+#define HB_AHCI_BASE			0xffe08000
+
 #define HB_SREG_A9_PWR_REQ		0xfff3cf00
 #define HB_SREG_A9_BOOT_SRC_STAT	0xfff3cf04
+#define HB_SREG_A9_PWRDOM_STAT		0xfff3cf20
+
 #define HB_PWR_SUSPEND			0
 #define HB_PWR_SOFT_RESET		1
 #define HB_PWR_HARD_RESET		2
 #define HB_PWR_SHUTDOWN			3
 
+#define PWRDOM_STAT_SATA		0x80000000
+#define PWRDOM_STAT_PCI			0x40000000
+#define PWRDOM_STAT_EMMC		0x20000000
+
 DECLARE_GLOBAL_DATA_PTR;
 
 /*
@@ -43,13 +51,17 @@ int board_eth_init(bd_t *bis)
 	return rc;
 }
 
+#ifdef CONFIG_MISC_INIT_R
 int misc_init_r(void)
 {
 	char envbuffer[16];
 	u32 boot_choice;
+	u32 reg = readl(HB_SREG_A9_PWRDOM_STAT);
 
-	ahci_init(0xffe08000);
-	scsi_scan(1);
+	if (reg & PWRDOM_STAT_SATA) {
+		ahci_init(HB_AHCI_BASE);
+		scsi_scan(1);
+	}
 
 	boot_choice = readl(HB_SREG_A9_BOOT_SRC_STAT) & 0xff;
 	sprintf(envbuffer, "bootcmd%d", boot_choice);
@@ -61,6 +73,7 @@ int misc_init_r(void)
 
 	return 0;
 }
+#endif
 
 int dram_init(void)
 {
@@ -74,6 +87,22 @@ void dram_init_banksize(void)
 	gd->bd->bi_dram[0].size =  PHYS_SDRAM_1_SIZE;
 }
 
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *fdt, bd_t *bd)
+{
+	static const char disabled[] = "disabled";
+	u32 reg = readl(HB_SREG_A9_PWRDOM_STAT);
+
+	if (!(reg & PWRDOM_STAT_SATA))
+		do_fixup_by_compat(fdt, "calxeda,hb-ahci", "status",
+			disabled, sizeof(disabled), 1);
+
+	if (!(reg & PWRDOM_STAT_EMMC))
+		do_fixup_by_compat(fdt, "calxeda,hb-sdhci", "status",
+			disabled, sizeof(disabled), 1);
+}
+#endif
+
 void reset_cpu(ulong addr)
 {
 	writel(HB_PWR_HARD_RESET, HB_SREG_A9_PWR_REQ);
diff --git a/board/isee/igep0033/board.c b/board/isee/igep0033/board.c
index c0f0c0d..a24c22b 100644
--- a/board/isee/igep0033/board.c
+++ b/board/isee/igep0033/board.c
@@ -1,5 +1,5 @@
 /*
- * Board functions for IGEP COM AQUILA/CYGNUS based boards
+ * Board functions for IGEP COM AQUILA based boards
  *
  * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
  *
@@ -27,8 +27,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-
 /* MII mode defines */
 #define RMII_MODE_ENABLE	0x4D
 
@@ -66,60 +64,39 @@ static struct emif_regs ddr3_emif_reg_data = {
 	.zq_config = K4B2G1646EBIH9_ZQ_CFG,
 	.emif_ddr_phy_ctlr_1 = K4B2G1646EBIH9_EMIF_READ_LATENCY,
 };
-#endif
 
-/*
- * Early system init of muxing and clocks.
- */
-void s_init(void)
-{
-	/*
-	 * Save the boot parameters passed from romcode.
-	 * We cannot delay the saving further than this,
-	 * to prevent overwrites.
-	 */
-#ifdef CONFIG_SPL_BUILD
-	save_omap_boot_params();
-#endif
-
-	/* WDT1 is already running when the bootloader gets control
-	 * Disable it to avoid "random" resets
-	 */
-	writel(0xAAAA, &wdtimer->wdtwspr);
-	while (readl(&wdtimer->wdtwwps) != 0x0)
-		;
-	writel(0x5555, &wdtimer->wdtwspr);
-	while (readl(&wdtimer->wdtwwps) != 0x0)
-		;
+#define OSC    (V_OSCK/1000000)
+const struct dpll_params dpll_ddr = {
+		303, OSC-1, 1, -1, -1, -1, -1};
 
-#ifdef CONFIG_SPL_BUILD
-	/* Setup the PLLs and the clocks for the peripherals */
-	pll_init();
-
-	/* Enable RTC32K clock */
-	rtc32k_enable();
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	return &dpll_ddr;
+}
 
+void set_uart_mux_conf(void)
+{
 	enable_uart0_pin_mux();
+}
 
-	uart_soft_reset();
-	gd = &gdata;
-
-	preloader_console_init();
-
-	/* Configure board pin mux */
+void set_mux_conf_regs(void)
+{
 	enable_board_pin_mux();
+}
 
+void sdram_init(void)
+{
 	config_ddr(303, K4B2G1646EBIH9_IOCTRL_VALUE, &ddr3_data,
 		   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
-#endif
 }
+#endif
 
 /*
  * Basic board specific setup.  Pinmux has been handled already.
  */
 int board_init(void)
 {
-	gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
 	gpmc_init();
 
diff --git a/board/isee/igep0033/board.h b/board/isee/igep0033/board.h
index a6f17e3..a11d7ab 100644
--- a/board/isee/igep0033/board.h
+++ b/board/isee/igep0033/board.h
@@ -1,5 +1,5 @@
 /*
- * IGEP COM AQUILA/CYGNUS boards information header
+ * IGEP COM AQUILA boards information header
  *
  * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
  *
diff --git a/board/isee/igep00x0/igep00x0.c b/board/isee/igep00x0/igep00x0.c
index 77a9bc6..7a7500b 100644
--- a/board/isee/igep00x0/igep00x0.c
+++ b/board/isee/igep00x0/igep00x0.c
@@ -138,6 +138,18 @@ int board_mmc_init(bd_t *bis)
 }
 #endif
 
+void set_fdt(void)
+{
+	switch (gd->bd->bi_arch_number) {
+	case MACH_TYPE_IGEP0020:
+		setenv("dtbfile", "omap3-igep0020.dtb");
+		break;
+	case MACH_TYPE_IGEP0030:
+		setenv("dtbfile", "omap3-igep0030.dtb");
+		break;
+	}
+}
+
 /*
  * Routine: misc_init_r
  * Description: Configure board specific parts
@@ -150,6 +162,8 @@ int misc_init_r(void)
 
 	dieid_num_r();
 
+	set_fdt();
+
 	return 0;
 }
 
diff --git a/board/overo/overo.c b/board/overo/overo.c
index a6e2e93..aace42a 100644
--- a/board/overo/overo.c
+++ b/board/overo/overo.c
@@ -142,16 +142,22 @@ void get_board_mem_timings(struct board_sdrc_timings *timings)
 		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 		break;
 	case REVISION_1: /* Micron 256MB/512MB, 1/2 banks of 256MB */
-		timings->mcfg = MICRON_V_MCFG_165(256 << 20);
-		timings->ctrla = MICRON_V_ACTIMA_165;
-		timings->ctrlb = MICRON_V_ACTIMB_165;
-		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+		timings->ctrla = MICRON_V_ACTIMA_200;
+		timings->ctrlb = MICRON_V_ACTIMB_200;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
 		break;
 	case REVISION_2: /* Hynix 256MB/512MB, 1/2 banks of 256MB */
-		timings->mcfg = HYNIX_V_MCFG_165(256 << 20);
-		timings->ctrla = HYNIX_V_ACTIMA_165;
-		timings->ctrlb = HYNIX_V_ACTIMB_165;
-		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
+		timings->ctrla = HYNIX_V_ACTIMA_200;
+		timings->ctrlb = HYNIX_V_ACTIMB_200;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+		break;
+	case REVISION_3: /* Micron 512MB/1024MB, 1/2 banks of 512MB */
+		timings->mcfg = MCFG(512 << 20, 15);
+		timings->ctrla = MICRON_V_ACTIMA_200;
+		timings->ctrlb = MICRON_V_ACTIMB_200;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
 		break;
 	default:
 		timings->mcfg = MICRON_V_MCFG_165(128 << 20);
diff --git a/board/overo/overo.h b/board/overo/overo.h
index 88e197d..64604de 100644
--- a/board/overo/overo.h
+++ b/board/overo/overo.h
@@ -21,6 +21,7 @@ const omap3_sysinfo sysinfo = {
 #define REVISION_0	0x0
 #define REVISION_1	0x1
 #define REVISION_2	0x2
+#define REVISION_3	0x3
 
 /*
  * IEN  - Input Enable
diff --git a/board/phytec/pcm051/board.c b/board/phytec/pcm051/board.c
index 6291d03..f53c5bb 100644
--- a/board/phytec/pcm051/board.c
+++ b/board/phytec/pcm051/board.c
@@ -30,8 +30,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-
 /* MII mode defines */
 #define MII_MODE_ENABLE		0x0
 #define RGMII_MODE_ENABLE	0xA
@@ -44,6 +42,15 @@ static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
 /* DDR RAM defines */
 #define DDR_CLK_MHZ		303 /* DDR_DPLL_MULT value */
 
+#define OSC	(V_OSCK/1000000)
+const struct dpll_params dpll_ddr = {
+		DDR_CLK_MHZ, OSC-1, 1, -1, -1, -1, -1};
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	return &dpll_ddr;
+}
+
 static const struct ddr_data ddr3_data = {
 	.datardsratio0 = MT41J256M8HX15E_RD_DQS,
 	.datawdsratio0 = MT41J256M8HX15E_WR_DQS,
@@ -76,57 +83,27 @@ static struct emif_regs ddr3_emif_reg_data = {
 	.emif_ddr_phy_ctlr_1 = MT41J256M8HX15E_EMIF_READ_LATENCY |
 				PHY_EN_DYN_PWRDN,
 };
-#endif
 
-/*
- * early system init of muxing and clocks.
- */
-void s_init(void)
+void set_uart_mux_conf(void)
 {
-	/*
-	 * Save the boot parameters passed from romcode.
-	 * We cannot delay the saving further than this,
-	 * to prevent overwrites.
-	 */
-#ifdef CONFIG_SPL_BUILD
-	save_omap_boot_params();
-#endif
-
-	/*
-	 * WDT1 is already running when the bootloader gets control
-	 * Disable it to avoid "random" resets
-	 */
-	writel(0xAAAA, &wdtimer->wdtwspr);
-	while (readl(&wdtimer->wdtwwps) != 0x0)
-		;
-	writel(0x5555, &wdtimer->wdtwspr);
-	while (readl(&wdtimer->wdtwwps) != 0x0)
-		;
-
-#ifdef CONFIG_SPL_BUILD
-	/* Setup the PLLs and the clocks for the peripherals */
-	pll_init();
-
-	/* Enable RTC32K clock */
-	rtc32k_enable();
-
 	enable_uart0_pin_mux();
-	uart_soft_reset();
-
-	gd = &gdata;
-
-	preloader_console_init();
+}
 
+void set_mux_conf_regs(void)
+{
 	/* Initalize the board header */
 	enable_i2c0_pin_mux();
 	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
 
 	enable_board_pin_mux();
+}
 
+void sdram_init(void)
+{
 	config_ddr(DDR_CLK_MHZ, MT41J256M8HX15E_IOCTRL_VALUE, &ddr3_data,
 			&ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
-#endif
 }
+#endif
 
 /*
  * Basic board specific setup.  Pinmux has been handled already.
@@ -135,7 +112,7 @@ int board_init(void)
 {
 	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
 
-	gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
 	return 0;
 }
diff --git a/board/ti/am335x/Makefile b/board/ti/am335x/Makefile
index cb2b999..3dbeeda 100644
--- a/board/ti/am335x/Makefile
+++ b/board/ti/am335x/Makefile
@@ -10,7 +10,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(BOARD).o
 
-ifdef CONFIG_SPL_BUILD
+ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_NOR_BOOT),y)
 COBJS	:= mux.o
 endif
 
diff --git a/board/ti/am335x/README b/board/ti/am335x/README
new file mode 100644
index 0000000..67b5246
--- /dev/null
+++ b/board/ti/am335x/README
@@ -0,0 +1,160 @@
+Summary
+=======
+
+This document covers various features of the 'am335x_evm' build, and some of
+the related build targets (am335x_evm_uartN, etc).
+
+Hardware
+========
+
+The binary produced by this board supports, based on parsing of the EEPROM
+documented in TI's reference designs:
+- AM335x GP EVM
+- AM335x EVM SK
+- Beaglebone White
+- Beaglebone Black
+'
+NAND
+====
+
+The AM335x GP EVM ships with a 256MiB NAND available in most profiles.  In
+this example to program the NAND we assume that an SD card has been
+inserted with the files to write in the first SD slot and that mtdparts
+have been configured correctly for the board.  As a time saving measure we
+load MLO into memory in one location, copy it into the three locatations
+that the ROM checks for additional valid copies, then load U-Boot into
+memory.  We then write that whole section of memory to NAND.
+
+U-Boot # mmc rescan
+U-Boot # env default -f -a
+U-Boot # nand erase.chip
+U-Boot # saveenv
+U-Boot # load mmc 0 81000000 MLO
+U-Boot # cp.b 81000000 81020000 20000
+U-Boot # cp.b 81000000 81040000 20000
+U-Boot # cp.b 81000000 81060000 20000
+U-Boot # load mmc 0 81080000 u-boot.img
+U-Boot # nand write 81000000 0 260000
+U-Boot # load mmc 0 ${loadaddr} uImage
+U-Boot # nand write ${loadaddr} kernel 500000
+
+NOR
+===
+
+The Beaglebone White can be equiped with a "memory cape" that in turn can
+have a NOR module plugged into it.  In this case it is then possible to
+program and boot from NOR.  Note that due to how U-Boot is architectured we
+must build a specific version of U-Boot that knows we have NOR flash.  This
+build is named 'am335x_evm_nor'.  Further, we have a 'am335x_evm_norboot'
+build that will assume that the environment is on NOR rather than NAND.  In
+the following example we assume that and SD card has been populated with
+MLO and u-boot.img from a 'am335x_evm_nor' build and also contains the
+'u-boot.bin' from a 'am335x_evm_norboot' build.  When booting from NOR, a
+binary must be written to the start of NOR, with no header or similar
+prepended.  In the following example we use a size of 512KiB (0x80000)
+as that is how much space we set aside before the environment, as per
+the config file.
+
+U-Boot # mmc rescan
+U-Boot # load mmc 0 ${loadaddr} u-boot.bin
+U-Boot # protect off 08000000 +80000
+U-Boot # erase 08000000 +80000
+U-Boot # cp.b ${loadaddr} 08000000 ${filesize}
+
+Falcon Mode
+===========
+
+The default build includes "Falcon Mode" (see doc/README.falcon) via NAND,
+eMMC (or raw SD cards) and FAT SD cards.  Our default behavior currently is
+to read a 'c' on the console while in SPL at any point prior to loading the
+OS payload (so as soon as possible) to opt to booting full U-Boot.  Also
+note that while one can program Falcon Mode "in place" great care needs to
+be taken by the user to not 'brick' their setup.  As these are all eval
+boards with multiple boot methods, recovery should not be an issue in this
+worst-case however.
+
+Falcon Mode: eMMC
+=================
+
+The recommended layout in this case is:
+
+MMC BLOCKS      |--------------------------------| LOCATION IN BYTES
+0x0000 - 0x007F : MBR or GPT table               : 0x000000 - 0x020000
+0x0080 - 0x00FF : ARGS or FDT file               : 0x010000 - 0x020000
+0x0100 - 0x01FF : SPL.backup1 (first copy used)  : 0x020000 - 0x040000
+0x0200 - 0x02FF : SPL.backup2 (second copy used) : 0x040000 - 0x060000
+0x0300 - 0x06FF : U-Boot                         : 0x060000 - 0x0e0000
+0x0700 - 0x08FF : U-Boot Env + Redundant         : 0x0e0000 - 0x120000
+0x0900 - 0x28FF : Kernel                         : 0x120000 - 0x520000
+
+Note that when we run 'spl export' it will prepare to boot the kernel.
+This includes relocation of the uImage from where we loaded it to the entry
+point defined in the header.  As these locations overlap by default, it
+would leave us with an image that if written to MMC will not boot, so
+instead of using the loadaddr variable we use 0x81000000 in the following
+example.  In this example we are loading from the network, for simplicity,
+and assume a valid partition table already exists and 'mmc dev' has already
+been run to select the correct device.  Also note that if you previously
+had a FAT partition (such as on a Beaglebone Black) it is not enough to
+write garbage into the area, you must delete it from the partition table
+first.
+
+# Ensure we are able to talk with this mmc device
+U-Boot # mmc rescan
+U-Boot # tftp 81000000 am335x/MLO
+# Write to two of the backup locations ROM uses
+U-Boot # mmc write 81000000 100 100
+U-Boot # mmc write 81000000 200 100
+# Write U-Boot to the location set in the config
+U-Boot # tftp 81000000 am335x/u-boot.img
+U-Boot # mmc write 81000000 300 400
+# Load kernel and device tree into memory, perform export
+U-Boot # tftp 81000000 am335x/uImage
+U-Boot # run findfdt
+U-Boot # tftp ${fdtaddr} am335x/${fdtfile}
+U-Boot # run mmcargs
+U-Boot # spl export fdt 81000000 - ${fdtaddr}
+# Write the updated device tree to MMC
+U-Boot # mmc write ${fdtaddr} 80 80
+# Write the uImage to MMC
+U-Boot # mmc write 81000000 900 2000
+
+Falcon Mode: FAT SD cards
+=========================
+
+In this case the additional file is written to the filesystem.  In this
+example we assume that the uImage and device tree to be used are already on
+the FAT filesystem (only the uImage MUST be for this to function
+afterwards) along with a Falcon Mode aware MLO and the FAT partition has
+already been created and marked bootable:
+
+U-Boot # mmc rescan
+# Load kernel and device tree into memory, perform export
+U-Boot # load mmc 0:1 ${loadaddr} uImage
+U-Boot # run findfdt
+U-Boot # load mmc 0:1 ${fdtaddr} ${fdtfile}
+U-Boot # run mmcargs
+U-Boot # spl export fdt ${loadaddr} - ${fdtaddr}
+
+This will print a number of lines and then end with something like:
+   Using Device Tree in place at 80f80000, end 80f85928
+   Using Device Tree in place at 80f80000, end 80f88928
+So then you:
+
+U-Boot # fatwrite mmc 0:1 0x80f80000 args 8928
+
+Falcon Mode: NAND
+=================
+
+In this case the additional data is written to another partition of the
+NAND.  In this example we assume that the uImage and device tree to be are
+already located on the NAND somewhere (such as fileystem or mtd partition)
+along with a Falcon Mode aware MLO written to the correct locations for
+booting and mtdparts have been configured correctly for the board:
+
+U-Boot # nand read ${loadaddr} kernel
+U-Boot # load nand rootfs ${fdtaddr} /boot/am335x-evm.dtb
+U-Boot # run nandargs
+U-Boot # spl export fdt ${loadaddr} - ${fdtaddr}
+U-Boot # nand erase.part u-boot-spl-os
+U-Boot # nand write ${fdtaddr} u-boot-spl-os
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 7138d73..04c37e2 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -19,6 +19,7 @@
 #include <asm/arch/gpio.h>
 #include <asm/arch/mmc_host_def.h>
 #include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
 #include <asm/io.h>
 #include <asm/emif.h>
 #include <asm/gpio.h>
@@ -29,8 +30,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-
 /* MII mode defines */
 #define MII_MODE_ENABLE		0x0
 #define RGMII_MODE_ENABLE	0x3A
@@ -40,43 +39,10 @@ static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
 
 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
 
-static struct am335x_baseboard_id __attribute__((section (".data"))) header;
-
-static inline int board_is_bone(void)
-{
-	return !strncmp(header.name, "A335BONE", HDR_NAME_LEN);
-}
-
-static inline int board_is_bone_lt(void)
-{
-	return !strncmp(header.name, "A335BNLT", HDR_NAME_LEN);
-}
-
-static inline int board_is_evm_sk(void)
-{
-	return !strncmp("A335X_SK", header.name, HDR_NAME_LEN);
-}
-
-static inline int board_is_idk(void)
-{
-	return !strncmp(header.config, "SKU#02", 6);
-}
-
-static int __maybe_unused board_is_gp_evm(void)
-{
-	return !strncmp("A33515BB", header.name, 8);
-}
-
-int board_is_evm_15_or_later(void)
-{
-	return (!strncmp("A33515BB", header.name, 8) &&
-		strncmp("1.5", header.version, 3) <= 0);
-}
-
 /*
  * Read header information from EEPROM into global structure.
  */
-static int read_eeprom(void)
+static int read_eeprom(struct am335x_baseboard_id *header)
 {
 	/* Check if baseboard eeprom is available */
 	if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) {
@@ -86,28 +52,28 @@ static int read_eeprom(void)
 	}
 
 	/* read the eeprom using i2c */
-	if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)&header,
-							sizeof(header))) {
+	if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header,
+		     sizeof(struct am335x_baseboard_id))) {
 		puts("Could not read the EEPROM; something fundamentally"
 			" wrong on the I2C bus.\n");
 		return -EIO;
 	}
 
-	if (header.magic != 0xEE3355AA) {
+	if (header->magic != 0xEE3355AA) {
 		/*
 		 * read the eeprom using i2c again,
 		 * but use only a 1 byte address
 		 */
-		if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1,
-					(uchar *)&header, sizeof(header))) {
+		if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
+			     sizeof(struct am335x_baseboard_id))) {
 			puts("Could not read the EEPROM; something "
 				"fundamentally wrong on the I2C bus.\n");
 			return -EIO;
 		}
 
-		if (header.magic != 0xEE3355AA) {
+		if (header->magic != 0xEE3355AA) {
 			printf("Incorrect magic number (0x%x) in EEPROM\n",
-					header.magic);
+					header->magic);
 			return -EINVAL;
 		}
 	}
@@ -115,7 +81,7 @@ static int read_eeprom(void)
 	return 0;
 }
 
-#ifdef CONFIG_SPL_BUILD
+#if defined(CONFIG_SPL_BUILD) || defined(CONFIG_NOR_BOOT)
 static const struct ddr_data ddr2_data = {
 	.datardsratio0 = ((MT47H128M16RT25E_RD_DQS<<30) |
 			  (MT47H128M16RT25E_RD_DQS<<20) |
@@ -274,39 +240,35 @@ int spl_start_uboot(void)
 }
 #endif
 
-#endif
+#define OSC	(V_OSCK/1000000)
+const struct dpll_params dpll_ddr = {
+		266, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_evm_sk = {
+		303, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_bone_black = {
+		400, OSC-1, 1, -1, -1, -1, -1};
 
-/*
- * early system init of muxing and clocks.
- */
-void s_init(void)
+const struct dpll_params *get_dpll_ddr_params(void)
 {
-	/*
-	 * Save the boot parameters passed from romcode.
-	 * We cannot delay the saving further than this,
-	 * to prevent overwrites.
-	 */
-#ifdef CONFIG_SPL_BUILD
-	save_omap_boot_params();
-#endif
-
-	/* WDT1 is already running when the bootloader gets control
-	 * Disable it to avoid "random" resets
-	 */
-	writel(0xAAAA, &wdtimer->wdtwspr);
-	while (readl(&wdtimer->wdtwwps) != 0x0)
-		;
-	writel(0x5555, &wdtimer->wdtwspr);
-	while (readl(&wdtimer->wdtwwps) != 0x0)
-		;
+	struct am335x_baseboard_id header;
 
-#ifdef CONFIG_SPL_BUILD
-	/* Setup the PLLs and the clocks for the peripherals */
-	pll_init();
+	enable_i2c0_pin_mux();
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	if (read_eeprom(&header) < 0)
+		puts("Could not get board ID.\n");
 
-	/* Enable RTC32K clock */
-	rtc32k_enable();
+	if (board_is_evm_sk(&header))
+		return &dpll_ddr_evm_sk;
+	else if (board_is_bone_lt(&header))
+		return &dpll_ddr_bone_black;
+	else if (board_is_evm_15_or_later(&header))
+		return &dpll_ddr_evm_sk;
+	else
+		return &dpll_ddr;
+}
 
+void set_uart_mux_conf(void)
+{
 #ifdef CONFIG_SERIAL1
 	enable_uart0_pin_mux();
 #endif /* CONFIG_SERIAL1 */
@@ -325,21 +287,26 @@ void s_init(void)
 #ifdef CONFIG_SERIAL6
 	enable_uart5_pin_mux();
 #endif /* CONFIG_SERIAL6 */
+}
 
-	uart_soft_reset();
+void set_mux_conf_regs(void)
+{
+	__maybe_unused struct am335x_baseboard_id header;
 
-	gd = &gdata;
+	if (read_eeprom(&header) < 0)
+		puts("Could not get board ID.\n");
 
-	preloader_console_init();
+	enable_board_pin_mux(&header);
+}
 
-	/* Initalize the board header */
-	enable_i2c0_pin_mux();
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-	if (read_eeprom() < 0)
+void sdram_init(void)
+{
+	__maybe_unused struct am335x_baseboard_id header;
+
+	if (read_eeprom(&header) < 0)
 		puts("Could not get board ID.\n");
 
-	enable_board_pin_mux(&header);
-	if (board_is_evm_sk()) {
+	if (board_is_evm_sk(&header)) {
 		/*
 		 * EVM SK 1.2A and later use gpio0_7 to enable DDR3.
 		 * This is safe enough to do on older revs.
@@ -348,36 +315,44 @@ void s_init(void)
 		gpio_direction_output(GPIO_DDR_VTT_EN, 1);
 	}
 
-	if (board_is_evm_sk())
+	if (board_is_evm_sk(&header))
 		config_ddr(303, MT41J128MJT125_IOCTRL_VALUE, &ddr3_data,
 			   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
-	else if (board_is_bone_lt())
+	else if (board_is_bone_lt(&header))
 		config_ddr(400, MT41K256M16HA125E_IOCTRL_VALUE,
 			   &ddr3_beagleblack_data,
 			   &ddr3_beagleblack_cmd_ctrl_data,
 			   &ddr3_beagleblack_emif_reg_data, 0);
-	else if (board_is_evm_15_or_later())
+	else if (board_is_evm_15_or_later(&header))
 		config_ddr(303, MT41J512M8RH125_IOCTRL_VALUE, &ddr3_evm_data,
 			   &ddr3_evm_cmd_ctrl_data, &ddr3_evm_emif_reg_data, 0);
 	else
 		config_ddr(266, MT47H128M16RT25E_IOCTRL_VALUE, &ddr2_data,
 			   &ddr2_cmd_ctrl_data, &ddr2_emif_reg_data, 0);
-#endif
 }
+#endif
 
 /*
  * Basic board specific setup.  Pinmux has been handled already.
  */
 int board_init(void)
 {
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-	if (read_eeprom() < 0)
-		puts("Could not get board ID.\n");
+#ifdef CONFIG_NOR
+	const u32 gpmc_nor[GPMC_MAX_REG] = { STNOR_GPMC_CONFIG1,
+		STNOR_GPMC_CONFIG2, STNOR_GPMC_CONFIG3, STNOR_GPMC_CONFIG4,
+		STNOR_GPMC_CONFIG5, STNOR_GPMC_CONFIG6, STNOR_GPMC_CONFIG7 };
+#endif
 
-	gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
 	gpmc_init();
 
+#ifdef CONFIG_NOR
+	/* Reconfigure CS0 for NOR instead of NAND. */
+	enable_gpmc_cs_config(gpmc_nor, &gpmc_cfg->cs[0],
+			      CONFIG_SYS_FLASH_BASE, GPMC_SIZE_16M);
+#endif
+
 	return 0;
 }
 
@@ -386,6 +361,10 @@ int board_late_init(void)
 {
 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 	char safe_string[HDR_NAME_LEN + 1];
+	struct am335x_baseboard_id header;
+
+	if (read_eeprom(&header) < 0)
+		puts("Could not get board ID.\n");
 
 	/* Now set variables based on the header. */
 	strncpy(safe_string, (char *)header.name, sizeof(header.name));
@@ -435,6 +414,7 @@ static struct cpsw_platform_data cpsw_data = {
 	.ale_entries		= 1024,
 	.host_port_reg_ofs	= 0x108,
 	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
 	.mac_control		= (1 << 5),
 	.control		= cpsw_control,
 	.host_port_num		= 0,
@@ -449,6 +429,7 @@ int board_eth_init(bd_t *bis)
 	int rv, n = 0;
 	uint8_t mac_addr[6];
 	uint32_t mac_hi, mac_lo;
+	__maybe_unused struct am335x_baseboard_id header;
 
 	/* try reading mac address from efuse */
 	mac_lo = readl(&cdev->macid0l);
@@ -470,7 +451,11 @@ int board_eth_init(bd_t *bis)
 	}
 
 #ifdef CONFIG_DRIVER_TI_CPSW
-	if (board_is_bone() || board_is_bone_lt() || board_is_idk()) {
+	if (read_eeprom(&header) < 0)
+		puts("Could not get board ID.\n");
+
+	if (board_is_bone(&header) || board_is_bone_lt(&header) ||
+	    board_is_idk(&header)) {
 		writel(MII_MODE_ENABLE, &cdev->miisel);
 		cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
 				PHY_INTERFACE_MODE_MII;
@@ -499,7 +484,7 @@ int board_eth_init(bd_t *bis)
 #define AR8051_DEBUG_RGMII_CLK_DLY_REG	0x5
 #define AR8051_RGMII_TX_CLK_DLY		0x100
 
-	if (board_is_evm_sk() || board_is_gp_evm()) {
+	if (board_is_evm_sk(&header) || board_is_gp_evm(&header)) {
 		const char *devname;
 		devname = miiphy_get_current_dev();
 
diff --git a/board/ti/am335x/board.h b/board/ti/am335x/board.h
index 9fea1f1..bc700d5 100644
--- a/board/ti/am335x/board.h
+++ b/board/ti/am335x/board.h
@@ -29,6 +29,37 @@ struct am335x_baseboard_id {
 	char mac_addr[HDR_NO_OF_MAC_ADDR][HDR_ETH_ALEN];
 };
 
+static inline int board_is_bone(struct am335x_baseboard_id *header)
+{
+	return !strncmp(header->name, "A335BONE", HDR_NAME_LEN);
+}
+
+static inline int board_is_bone_lt(struct am335x_baseboard_id *header)
+{
+	return !strncmp(header->name, "A335BNLT", HDR_NAME_LEN);
+}
+
+static inline int board_is_evm_sk(struct am335x_baseboard_id *header)
+{
+	return !strncmp("A335X_SK", header->name, HDR_NAME_LEN);
+}
+
+static inline int board_is_idk(struct am335x_baseboard_id *header)
+{
+	return !strncmp(header->config, "SKU#02", 6);
+}
+
+static inline int board_is_gp_evm(struct am335x_baseboard_id *header)
+{
+	return !strncmp("A33515BB", header->name, HDR_NAME_LEN);
+}
+
+static inline int board_is_evm_15_or_later(struct am335x_baseboard_id *header)
+{
+	return (board_is_gp_evm(header) &&
+		strncmp("1.5", header->version, 3) <= 0);
+}
+
 /*
  * We have three pin mux functions that must exist.  We must be able to enable
  * uart0, for initial output and i2c0 to read the main EEPROM.  We then have a
diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c
index 0283708..b2bfda5 100644
--- a/board/ti/am335x/mux.c
+++ b/board/ti/am335x/mux.c
@@ -190,6 +190,75 @@ static struct module_pin_mux nand_pin_mux[] = {
 	{-1},
 };
 
+#if defined(CONFIG_NOR) && !defined(CONFIG_NOR_BOOT)
+static struct module_pin_mux bone_norcape_pin_mux[] = {
+	{OFFSET(lcd_data0), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A0 */
+	{OFFSET(lcd_data1), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A1 */
+	{OFFSET(lcd_data2), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A2 */
+	{OFFSET(lcd_data3), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A3 */
+	{OFFSET(lcd_data4), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A4 */
+	{OFFSET(lcd_data5), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A5 */
+	{OFFSET(lcd_data6), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A6 */
+	{OFFSET(lcd_data7), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A7 */
+	{OFFSET(lcd_vsync), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A8 */
+	{OFFSET(lcd_hsync), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A9 */
+	{OFFSET(lcd_pclk), MODE(1)| PULLUDEN | RXACTIVE},       /* NOR_A10 */
+	{OFFSET(lcd_ac_bias_en), MODE(1)| PULLUDEN | RXACTIVE}, /* NOR_A11 */
+	{OFFSET(lcd_data8), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A12 */
+	{OFFSET(lcd_data9), MODE(1) | PULLUDEN | RXACTIVE},     /* NOR_A13 */
+	{OFFSET(lcd_data10), MODE(1) | PULLUDEN | RXACTIVE},    /* NOR_A14 */
+	{OFFSET(lcd_data11), MODE(1) | PULLUDEN | RXACTIVE},    /* NOR_A15 */
+	{OFFSET(lcd_data12), MODE(1) | PULLUDEN | RXACTIVE},    /* NOR_A16 */
+	{OFFSET(lcd_data13), MODE(1) | PULLUDEN | RXACTIVE},    /* NOR_A17 */
+	{OFFSET(lcd_data14), MODE(1) | PULLUDEN | RXACTIVE},    /* NOR_A18 */
+	{OFFSET(lcd_data15), MODE(1) | PULLUDEN | RXACTIVE},    /* NOR_A19 */
+	{OFFSET(gpmc_ad0), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD0 */
+	{OFFSET(gpmc_ad1), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD1 */
+	{OFFSET(gpmc_ad2), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD2 */
+	{OFFSET(gpmc_ad3), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD3 */
+	{OFFSET(gpmc_ad4), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD4 */
+	{OFFSET(gpmc_ad5), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD5 */
+	{OFFSET(gpmc_ad6), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD6 */
+	{OFFSET(gpmc_ad7), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD7 */
+	{OFFSET(gpmc_ad8), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD8 */
+	{OFFSET(gpmc_ad9), MODE(0) | PULLUDEN | RXACTIVE},      /* NOR_AD9 */
+	{OFFSET(gpmc_ad10), MODE(0) | PULLUDEN | RXACTIVE},     /* NOR_AD10 */
+	{OFFSET(gpmc_ad11), MODE(0) | PULLUDEN | RXACTIVE},     /* NOR_AD11 */
+	{OFFSET(gpmc_ad12), MODE(0) | PULLUDEN | RXACTIVE},     /* NOR_AD12 */
+	{OFFSET(gpmc_ad13), MODE(0) | PULLUDEN | RXACTIVE},     /* NOR_AD13 */
+	{OFFSET(gpmc_ad14), MODE(0) | PULLUDEN | RXACTIVE},     /* NOR_AD14 */
+	{OFFSET(gpmc_ad15), MODE(0) | PULLUDEN | RXACTIVE},     /* NOR_AD15 */
+
+	{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN) | RXACTIVE},   /* NOR_CE */
+	{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN) | RXACTIVE}, /* NOR_ADVN_ALE */
+	{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN | RXACTIVE)},/* NOR_OE */
+	{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN | RXACTIVE)},/* NOR_BE0N_CLE */
+	{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN | RXACTIVE)},    /* NOR_WEN */
+	{OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUDEN)}, /* NOR WAIT */
+	{-1},
+};
+#endif
+
+#if defined(CONFIG_NOR_BOOT)
+static struct module_pin_mux norboot_pin_mux[] = {
+	{OFFSET(lcd_data1), MODE(1) | PULLUDDIS},
+	{OFFSET(lcd_data2), MODE(1) | PULLUDDIS},
+	{OFFSET(lcd_data3), MODE(1) | PULLUDDIS},
+	{OFFSET(lcd_data4), MODE(1) | PULLUDDIS},
+	{OFFSET(lcd_data5), MODE(1) | PULLUDDIS},
+	{OFFSET(lcd_data6), MODE(1) | PULLUDDIS},
+	{OFFSET(lcd_data7), MODE(1) | PULLUDDIS},
+	{OFFSET(lcd_data8), MODE(1) | PULLUDDIS},
+	{OFFSET(lcd_data9), MODE(1) | PULLUDDIS},
+	{-1},
+};
+
+void enable_norboot_pin_mux(void)
+{
+	configure_module_pin_mux(norboot_pin_mux);
+}
+#endif
+
 void enable_uart0_pin_mux(void)
 {
 	configure_module_pin_mux(uart0_pin_mux);
@@ -262,13 +331,18 @@ static unsigned short detect_daughter_board_profile(void)
 void enable_board_pin_mux(struct am335x_baseboard_id *header)
 {
 	/* Do board-specific muxes. */
-	if (!strncmp(header->name, "A335BONE", HDR_NAME_LEN)) {
+	if (board_is_bone(header)) {
 		/* Beaglebone pinmux */
 		configure_module_pin_mux(i2c1_pin_mux);
 		configure_module_pin_mux(mii1_pin_mux);
 		configure_module_pin_mux(mmc0_pin_mux);
+#ifndef CONFIG_NOR
 		configure_module_pin_mux(mmc1_pin_mux);
-	} else if (!strncmp(header->config, "SKU#01", 6)) {
+#endif
+#if defined(CONFIG_NOR) && !defined(CONFIG_NOR_BOOT)
+		configure_module_pin_mux(bone_norcape_pin_mux);
+#endif
+	} else if (board_is_gp_evm(header)) {
 		/* General Purpose EVM */
 		unsigned short profile = detect_daughter_board_profile();
 		configure_module_pin_mux(rgmii1_pin_mux);
@@ -283,7 +357,7 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header)
 			configure_module_pin_mux(mmc1_pin_mux);
 			configure_module_pin_mux(spi0_pin_mux);
 		}
-	} else if (!strncmp(header->config, "SKU#02", 6)) {
+	} else if (board_is_idk(header)) {
 		/*
 		 * Industrial Motor Control (IDK)
 		 * note: IDK console is on UART3 by default.
@@ -292,13 +366,13 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header)
 		 */
 		configure_module_pin_mux(mii1_pin_mux);
 		configure_module_pin_mux(mmc0_no_cd_pin_mux);
-	} else if (!strncmp(header->name, "A335X_SK", HDR_NAME_LEN)) {
+	} else if (board_is_evm_sk(header)) {
 		/* Starter Kit EVM */
 		configure_module_pin_mux(i2c1_pin_mux);
 		configure_module_pin_mux(gpio0_7_pin_mux);
 		configure_module_pin_mux(rgmii1_pin_mux);
 		configure_module_pin_mux(mmc0_pin_mux_sk_evm);
-	} else if (!strncmp(header->name, "A335BNLT", HDR_NAME_LEN)) {
+	} else if (board_is_bone_lt(header)) {
 		/* Beaglebone LT pinmux */
 		configure_module_pin_mux(i2c1_pin_mux);
 		configure_module_pin_mux(mii1_pin_mux);
diff --git a/board/ti/am335x/u-boot.lds b/board/ti/am335x/u-boot.lds
new file mode 100644
index 0000000..a173f62
--- /dev/null
+++ b/board/ti/am335x/u-boot.lds
@@ -0,0 +1,117 @@
+/*
+ * Copyright (c) 2004-2008 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text :
+	{
+		*(.__image_copy_start)
+		CPUDIR/start.o (.text*)
+		board/ti/am335x/libam335x.o (.text*)
+		*(.text*)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+	. = ALIGN(4);
+	.data : {
+		*(.data*)
+	}
+
+	. = ALIGN(4);
+
+	. = .;
+
+	. = ALIGN(4);
+	.u_boot_list : {
+		KEEP(*(SORT(.u_boot_list*)));
+	}
+
+	. = ALIGN(4);
+
+	.image_copy_end :
+	{
+		*(.__image_copy_end)
+	}
+
+	.rel_dyn_start :
+	{
+		*(.__rel_dyn_start)
+	}
+
+	.rel.dyn : {
+		*(.rel*)
+	}
+
+	.rel_dyn_end :
+	{
+		*(.__rel_dyn_end)
+	}
+
+	_end = .;
+
+	/*
+	 * Deprecated: this MMU section is used by pxa at present but
+	 * should not be used by new boards/CPUs.
+	 */
+	. = ALIGN(4096);
+	.mmutable : {
+		*(.mmutable)
+	}
+
+/*
+ * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
+ * __bss_base and __bss_limit are for linker only (overlay ordering)
+ */
+
+	.bss_start __rel_dyn_start (OVERLAY) : {
+		KEEP(*(.__bss_start));
+		__bss_base = .;
+	}
+
+	.bss __bss_base (OVERLAY) : {
+		*(.bss*)
+		 . = ALIGN(4);
+		 __bss_limit = .;
+	}
+
+	.bss_end __bss_limit (OVERLAY) : {
+		KEEP(*(.__bss_end));
+	}
+
+	/DISCARD/ : { *(.dynsym) }
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
+}
diff --git a/board/ti/am43xx/Makefile b/board/ti/am43xx/Makefile
new file mode 100644
index 0000000..4a1bb7c
--- /dev/null
+++ b/board/ti/am43xx/Makefile
@@ -0,0 +1,38 @@
+#
+# Makefile
+#
+# Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+ifdef CONFIG_SPL_BUILD
+COBJS	:= mux.o
+endif
+
+COBJS	+= board.o
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c
new file mode 100644
index 0000000..51b2576
--- /dev/null
+++ b/board/ti/am43xx/board.c
@@ -0,0 +1,57 @@
+/*
+ * board.c
+ *
+ * Board functions for TI AM43XX based boards
+ *
+ * Copyright (C) 2013, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mux.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_SPL_BUILD
+
+const struct dpll_params dpll_ddr = {
+		-1, -1, -1, -1, -1, -1, -1};
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	return &dpll_ddr;
+}
+
+void set_uart_mux_conf(void)
+{
+	enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+	enable_board_pin_mux();
+}
+
+void sdram_init(void)
+{
+}
+#endif
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+	return 0;
+}
+#endif
diff --git a/board/ti/am43xx/board.h b/board/ti/am43xx/board.h
new file mode 100644
index 0000000..8ca098b
--- /dev/null
+++ b/board/ti/am43xx/board.h
@@ -0,0 +1,17 @@
+/*
+ * board.h
+ *
+ * TI AM437x boards information header
+ * Derived from AM335x board.
+ *
+ * Copyright (C) 2013, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+void enable_uart0_pin_mux(void);
+void enable_board_pin_mux(void);
+#endif
diff --git a/board/ti/am43xx/mux.c b/board/ti/am43xx/mux.c
new file mode 100644
index 0000000..700e9a7
--- /dev/null
+++ b/board/ti/am43xx/mux.c
@@ -0,0 +1,27 @@
+/*
+ * mux.c
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mux.h>
+#include "board.h"
+
+static struct module_pin_mux uart0_pin_mux[] = {
+	{OFFSET(uart0_rxd), (MODE(0) | RXACTIVE)},	/* UART0_RXD */
+	{OFFSET(uart0_txd), (MODE(0))},			/* UART0_TXD */
+	{-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_board_pin_mux(void)
+{
+}
diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
index 36f7345..62e9bea 100644
--- a/board/ti/beagle/beagle.c
+++ b/board/ti/beagle/beagle.c
@@ -166,8 +166,7 @@ void get_board_mem_timings(struct board_sdrc_timings *timings)
 			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
 			break;
 		}
-	case REVISION_XM_A:
-	case REVISION_XM_B:
+	case REVISION_XM_AB:
 	case REVISION_XM_C:
 		if (pop_mfr == 0) {
 			/* 256MB DDR */
@@ -240,8 +239,7 @@ static void beagle_display_init(void)
 	case REVISION_C4:
 		omap3_dss_panel_config(&dvid_cfg);
 		break;
-	case REVISION_XM_A:
-	case REVISION_XM_B:
+	case REVISION_XM_AB:
 	case REVISION_XM_C:
 	default:
 		omap3_dss_panel_config(&dvid_cfg_xm);
@@ -260,12 +258,11 @@ static void beagle_dvi_pup(void)
 	case REVISION_AXBX:
 	case REVISION_CX:
 	case REVISION_C4:
-	case REVISION_XM_A:
 		gpio_request(170, "");
 		gpio_direction_output(170, 0);
 		gpio_set_value(170, 1);
 		break;
-	case REVISION_XM_B:
+	case REVISION_XM_AB:
 	case REVISION_XM_C:
 	default:
 		#define GPIODATADIR1 (TWL4030_BASEADD_GPIO+3)
@@ -343,19 +340,9 @@ int misc_init_r(void)
 					TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
 					TWL4030_PM_RECEIVER_DEV_GRP_P1);
 		break;
-	case REVISION_XM_A:
-		printf("Beagle xM Rev A\n");
-		setenv("beaglerev", "xMA");
-		MUX_BEAGLE_XM();
-		/* Set VAUX2 to 1.8V for EHCI PHY */
-		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
-					TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
-					TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
-					TWL4030_PM_RECEIVER_DEV_GRP_P1);
-		break;
-	case REVISION_XM_B:
-		printf("Beagle xM Rev B\n");
-		setenv("beaglerev", "xMB");
+	case REVISION_XM_AB:
+		printf("Beagle xM Rev A/B\n");
+		setenv("beaglerev", "xMAB");
 		MUX_BEAGLE_XM();
 		/* Set VAUX2 to 1.8V for EHCI PHY */
 		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
@@ -468,8 +455,7 @@ int misc_init_r(void)
 
 	twl4030_power_init();
 	switch (get_board_revision()) {
-	case REVISION_XM_A:
-	case REVISION_XM_B:
+	case REVISION_XM_AB:
 		twl4030_led_init(TWL4030_LED_LEDEN_LEDBON);
 		break;
 	default:
diff --git a/board/ti/beagle/beagle.h b/board/ti/beagle/beagle.h
index 76be358..6dd2ffe 100644
--- a/board/ti/beagle/beagle.h
+++ b/board/ti/beagle/beagle.h
@@ -23,8 +23,7 @@ const omap3_sysinfo sysinfo = {
 #define REVISION_AXBX	0x7
 #define REVISION_CX	0x6
 #define REVISION_C4	0x5
-#define REVISION_XM_A	0x0
-#define REVISION_XM_B	0x1
+#define REVISION_XM_AB	0x0
 #define REVISION_XM_C	0x2
 
 /*
diff --git a/board/ti/dra7xx/evm.c b/board/ti/dra7xx/evm.c
index 8190e4b..9a114e2 100644
--- a/board/ti/dra7xx/evm.c
+++ b/board/ti/dra7xx/evm.c
@@ -23,12 +23,53 @@
 #include <asm/ehci-omap.h>
 #endif
 
+#ifdef CONFIG_DRIVER_TI_CPSW
+#include <cpsw.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 const struct omap_sysinfo sysinfo = {
 	"Board: DRA7xx\n"
 };
 
+/*
+ * Adjust I/O delays on the Tx control and data lines of each MAC port. This
+ * is a workaround in order to work properly with the DP83865 PHYs on the EVM.
+ * In 3COM RGMII mode this PHY applies it's own internal clock delay, so we
+ * essentially need to counteract the DRA7xx internal delay, and we do this
+ * by delaying the control and data lines. If not using this PHY, you probably
+ * don't need to do this stuff!
+ */
+static void dra7xx_adj_io_delay(const struct io_delay *io_dly)
+{
+	int i = 0;
+	u32 reg_val;
+	u32 delta;
+	u32 coarse;
+	u32 fine;
+
+	writel(CFG_IO_DELAY_UNLOCK_KEY, CFG_IO_DELAY_LOCK);
+
+	while(io_dly[i].addr) {
+		writel(CFG_IO_DELAY_ACCESS_PATTERN & ~CFG_IO_DELAY_LOCK_MASK,
+		       io_dly[i].addr);
+		delta = io_dly[i].dly;
+		reg_val = readl(io_dly[i].addr) & 0x3ff;
+		coarse = ((reg_val >> 5) & 0x1F) + ((delta >> 5) & 0x1F);
+		coarse = (coarse > 0x1F) ? (0x1F) : (coarse);
+		fine = (reg_val & 0x1F) + (delta & 0x1F);
+		fine = (fine > 0x1F) ? (0x1F) : (fine);
+		reg_val = CFG_IO_DELAY_ACCESS_PATTERN |
+				CFG_IO_DELAY_LOCK_MASK |
+				((coarse << 5) | (fine));
+		writel(reg_val, io_dly[i].addr);
+		i++;
+	}
+
+	writel(CFG_IO_DELAY_LOCK_KEY, CFG_IO_DELAY_LOCK);
+}
+
 /**
  * @brief board_init
  *
@@ -42,11 +83,6 @@ int board_init(void)
 	return 0;
 }
 
-int board_eth_init(bd_t *bis)
-{
-	return 0;
-}
-
 /**
  * @brief misc_init_r - Configure EVM board specific configurations
  * such as power configurations, ethernet initialization as phase2 of
@@ -85,3 +121,107 @@ int board_mmc_init(bd_t *bis)
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+
+/* Delay value to add to calibrated value */
+#define RGMII0_TXCTL_DLY_VAL		((0x3 << 5) + 0x8)
+#define RGMII0_TXD0_DLY_VAL		((0x3 << 5) + 0x8)
+#define RGMII0_TXD1_DLY_VAL		((0x3 << 5) + 0x2)
+#define RGMII0_TXD2_DLY_VAL		((0x4 << 5) + 0x0)
+#define RGMII0_TXD3_DLY_VAL		((0x4 << 5) + 0x0)
+#define VIN2A_D13_DLY_VAL		((0x3 << 5) + 0x8)
+#define VIN2A_D17_DLY_VAL		((0x3 << 5) + 0x8)
+#define VIN2A_D16_DLY_VAL		((0x3 << 5) + 0x2)
+#define VIN2A_D15_DLY_VAL		((0x4 << 5) + 0x0)
+#define VIN2A_D14_DLY_VAL		((0x4 << 5) + 0x0)
+
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_id		= 0,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_id		= 1,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+	uint32_t ctrl_val;
+	const struct io_delay io_dly[] = {
+		{CFG_RGMII0_TXCTL, RGMII0_TXCTL_DLY_VAL},
+		{CFG_RGMII0_TXD0, RGMII0_TXD0_DLY_VAL},
+		{CFG_RGMII0_TXD1, RGMII0_TXD1_DLY_VAL},
+		{CFG_RGMII0_TXD2, RGMII0_TXD2_DLY_VAL},
+		{CFG_RGMII0_TXD3, RGMII0_TXD3_DLY_VAL},
+		{CFG_VIN2A_D13, VIN2A_D13_DLY_VAL},
+		{CFG_VIN2A_D17, VIN2A_D17_DLY_VAL},
+		{CFG_VIN2A_D16, VIN2A_D16_DLY_VAL},
+		{CFG_VIN2A_D15, VIN2A_D15_DLY_VAL},
+		{CFG_VIN2A_D14, VIN2A_D14_DLY_VAL},
+		{0}
+	};
+
+	/* Adjust IO delay for RGMII tx path */
+	dra7xx_adj_io_delay(io_dly);
+
+	/* try reading mac address from efuse */
+	mac_lo = readl((*ctrl)->control_core_mac_id_0_lo);
+	mac_hi = readl((*ctrl)->control_core_mac_id_0_hi);
+	mac_addr[0] = mac_hi & 0xFF;
+	mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+	mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+	mac_addr[3] = mac_lo & 0xFF;
+	mac_addr[4] = (mac_lo & 0xFF00) >> 8;
+	mac_addr[5] = (mac_lo & 0xFF0000) >> 16;
+
+	if (!getenv("ethaddr")) {
+		printf("<ethaddr> not set. Validating first E-fuse MAC\n");
+
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+	}
+	ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33);
+	ctrl_val |= 0x22;
+	writel(ctrl_val, (*ctrl)->control_core_control_io1);
+
+	ret = cpsw_register(&cpsw_data);
+	if (ret < 0)
+		printf("Error %d registering CPSW switch\n", ret);
+
+	return ret;
+}
+#endif
diff --git a/board/ti/dra7xx/mux_data.h b/board/ti/dra7xx/mux_data.h
index ec83422..0a86594 100644
--- a/board/ti/dra7xx/mux_data.h
+++ b/board/ti/dra7xx/mux_data.h
@@ -37,5 +37,19 @@ const struct pad_conf_entry core_padconf_array_essential[] = {
 	{UART1_RTSN, (IEN | PTU | PDIS | M3)},	/* UART1_RTSN */
 	{I2C1_SDA, (IEN | PTU | PDIS | M0)},	/* I2C1_SDA */
 	{I2C1_SCL, (IEN | PTU | PDIS | M0)},	/* I2C1_SCL */
+	{MDIO_MCLK, (PTU | PEN | M0)},		/* MDIO_MCLK  */
+	{MDIO_D, (IEN | PTU | PEN | M0)},	/* MDIO_D  */
+	{RGMII0_TXC, (M0) },
+	{RGMII0_TXCTL, (M0) },
+	{RGMII0_TXD3, (M0) },
+	{RGMII0_TXD2, (M0) },
+	{RGMII0_TXD1, (M0) },
+	{RGMII0_TXD0, (M0) },
+	{RGMII0_RXC, (IEN | M0) },
+	{RGMII0_RXCTL, (IEN | M0) },
+	{RGMII0_RXD3, (IEN | M0) },
+	{RGMII0_RXD2, (IEN | M0) },
+	{RGMII0_RXD1, (IEN | M0) },
+	{RGMII0_RXD0, (IEN | M0) },
 };
 #endif /* _MUX_DATA_DRA7XX_H_ */
diff --git a/board/ti/omap5_uevm/evm.c b/board/ti/omap5_uevm/evm.c
index ea83e6c..2c00648 100644
--- a/board/ti/omap5_uevm/evm.c
+++ b/board/ti/omap5_uevm/evm.c
@@ -10,6 +10,7 @@
 #include <palmas.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/arch/mmc_host_def.h>
+#include <tca642x.h>
 
 #include "mux_data.h"
 
@@ -20,6 +21,25 @@ const struct omap_sysinfo sysinfo = {
 };
 
 /**
+ * @brief tca642x_init - uEVM default values for the GPIO expander
+ * input reg, output reg, polarity reg, configuration reg
+ */
+struct tca642x_bank_info tca642x_init[] = {
+	{ .input_reg = 0x00,
+	  .output_reg = 0x04,
+	  .polarity_reg = 0x00,
+	  .configuration_reg = 0x80 },
+	{ .input_reg = 0x00,
+	  .output_reg = 0x00,
+	  .polarity_reg = 0x00,
+	  .configuration_reg = 0xff },
+	{ .input_reg = 0x00,
+	  .output_reg = 0x00,
+	  .polarity_reg = 0x00,
+	  .configuration_reg = 0x40 },
+};
+
+/**
  * @brief board_init
  *
  * @return 0
@@ -30,6 +50,8 @@ int board_init(void)
 	gd->bd->bi_arch_number = MACH_TYPE_OMAP5_SEVM;
 	gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */
 
+	tca642x_set_inital_state(CONFIG_SYS_I2C_TCA642X_ADDR, tca642x_init);
+
 	return 0;
 }
 
diff --git a/board/ti/omap5_uevm/mux_data.h b/board/ti/omap5_uevm/mux_data.h
index 36b723e..612c13e 100644
--- a/board/ti/omap5_uevm/mux_data.h
+++ b/board/ti/omap5_uevm/mux_data.h
@@ -40,6 +40,8 @@ const struct pad_conf_entry core_padconf_array_essential[] = {
 	{USBD0_HS_DP, (IEN | M0)},	/*  USBD0_HS_DP */
 	{USBD0_HS_DM, (IEN | M0)},	/*  USBD0_HS_DM */
 	{USBD0_SS_RX, (IEN | M0)},	/*  USBD0_SS_RX */
+	{I2C5_SCL, (IEN | M0)}, /* I2C5_SCL */
+	{I2C5_SDA, (IEN | M0)}, /* I2C5_SDA */
 
 };
 
diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c
index 17fba5a..e406326 100644
--- a/board/ti/ti814x/evm.c
+++ b/board/ti/ti814x/evm.c
@@ -27,30 +27,10 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef CONFIG_SPL_BUILD
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-#endif
-
 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
 
 /* UART Defines */
 #ifdef CONFIG_SPL_BUILD
-static void uart_enable(void)
-{
-	/* UART softreset */
-	uart_soft_reset();
-}
-
-static void wdt_disable(void)
-{
-	writel(0xAAAA, &wdtimer->wdtwspr);
-	while (readl(&wdtimer->wdtwwps) != 0x0)
-		;
-	writel(0x5555, &wdtimer->wdtwspr);
-	while (readl(&wdtimer->wdtwwps) != 0x0)
-		;
-}
-
 static const struct cmd_control evm_ddr2_cctrl_data = {
 	.cmd0csratio	= 0x80,
 	.cmd0dldiff	= 0x04,
@@ -100,68 +80,39 @@ static const struct ddr_data evm_ddr2_data = {
 	.datauserank0delay	= 1,
 	.datadldiff0		= 0x4,
 };
-#endif
 
-/*
- * early system init of muxing and clocks.
- */
-void s_init(void)
+void set_uart_mux_conf(void)
 {
-#ifdef CONFIG_SPL_BUILD
-	/*
-	 * Save the boot parameters passed from romcode.
-	 * We cannot delay the saving further than this,
-	 * to prevent overwrites.
-	 */
-#ifdef CONFIG_SPL_BUILD
-	save_omap_boot_params();
-#endif
-
-	/* WDT1 is already running when the bootloader gets control
-	 * Disable it to avoid "random" resets
-	 */
-	wdt_disable();
-
-	/* Enable timer */
-	timer_init();
-
-	/* Setup the PLLs and the clocks for the peripherals */
-	pll_init();
-
-	/* Enable RTC32K clock */
-	rtc32k_enable();
-
 	/* Set UART pins */
 	enable_uart0_pin_mux();
+}
 
+void set_mux_conf_regs(void)
+{
 	/* Set MMC pins */
 	enable_mmc1_pin_mux();
 
 	/* Set Ethernet pins */
 	enable_enet_pin_mux();
+}
 
-	/* Enable UART */
-	uart_enable();
-
-	gd = &gdata;
-
-	preloader_console_init();
-
+void sdram_init(void)
+{
 	config_dmm(&evm_lisa_map_regs);
 
 	config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data,
 		   &evm_ddr2_emif0_regs, 0);
 	config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data,
 		   &evm_ddr2_emif1_regs, 1);
-#endif
 }
+#endif
 
 /*
  * Basic board specific setup.  Pinmux has been handled already.
  */
 int board_init(void)
 {
-	gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 	return 0;
 }
 
@@ -207,6 +158,7 @@ static struct cpsw_platform_data cpsw_data = {
 	.ale_entries		= 1024,
 	.host_port_reg_ofs	= 0x28,
 	.hw_stats_reg_ofs	= 0x400,
+	.bd_ram_ofs		= 0x2000,
 	.mac_control		= (1 << 5),
 	.control		= cpsw_control,
 	.host_port_num		= 0,
diff --git a/board/ti/ti816x/Makefile b/board/ti/ti816x/Makefile
new file mode 100644
index 0000000..17ce72a
--- /dev/null
+++ b/board/ti/ti816x/Makefile
@@ -0,0 +1,37 @@
+#
+# Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
+# Antoine Tenart, <atenart@adeneo-embedded.com>
+#
+# Based on TI-PSP-04.00.02.14 :
+#
+# Copyright (C) 2009, Texas Instruments, Incorporated
+#
+# SPDX-License-Identifier:	GPL-2.0
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= evm.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+clean:
+	rm -f $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ti/ti816x/evm.c b/board/ti/ti816x/evm.c
new file mode 100644
index 0000000..74d35e9
--- /dev/null
+++ b/board/ti/ti816x/evm.c
@@ -0,0 +1,229 @@
+/*
+ * evm.c
+ *
+ * Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
+ * Antoine Tenart, <atenart@adeneo-embedded.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/cache.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mux.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+	return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+
+static struct module_pin_mux mmc_pin_mux[] = {
+	{ OFFSET(pincntl157), PULLDOWN_EN | PULLUDDIS | MODE(0x0) },
+	{ OFFSET(pincntl158), PULLDOWN_EN | PULLUDEN | MODE(0x0) },
+	{ OFFSET(pincntl159), PULLUP_EN | PULLUDDIS | MODE(0x0) },
+	{ OFFSET(pincntl160), PULLUP_EN | PULLUDDIS | MODE(0x0) },
+	{ OFFSET(pincntl161), PULLUP_EN | PULLUDDIS | MODE(0x0) },
+	{ OFFSET(pincntl162), PULLUP_EN | PULLUDDIS | MODE(0x0) },
+	{ OFFSET(pincntl163), PULLUP_EN | PULLUDDIS | MODE(0x0) },
+	{ -1 },
+};
+
+const struct dmm_lisa_map_regs evm_lisa_map_regs = {
+	.dmm_lisa_map_0 = 0x00000000,
+	.dmm_lisa_map_1 = 0x00000000,
+	.dmm_lisa_map_2 = 0x80640300,
+	.dmm_lisa_map_3 = 0xC0640320,
+};
+
+/*
+ * DDR2 related definitions
+ */
+#ifdef CONFIG_TI816X_EVM_DDR2
+static struct ddr_data ddr2_data = {
+	.datardsratio0		= ((0x40<<10) | (0x40<<0)),
+	.datawdsratio0		= ((0x4A<<10) | (0x4A<<0)),
+	.datawiratio0		= ((0x0<<10) | (0x0<<0)),
+	.datagiratio0		= ((0x0<<10) | (0x0<<0)),
+	.datafwsratio0		= ((0x13A<<10) | (0x13A<<0)),
+	.datawrsratio0		= ((0x8A<<10) | (0x8A<<0)),
+	.datauserank0delay	= 0x1,
+	.datadldiff0		= 0x0, /* depend on cpu rev, set later */
+};
+
+static struct cmd_control ddr2_ctrl = {
+	.cmd0csratio	= 0x80,
+	.cmd0dldiff	= 0x04, /* reset value is 0x4 */
+	.cmd0iclkout	= 0x00,
+
+	.cmd1csratio	= 0x80,
+	.cmd1dldiff	= 0x04, /* reset value is 0x4 */
+	.cmd1iclkout	= 0x00,
+
+	.cmd2csratio	= 0x80,
+	.cmd2dldiff	= 0x04, /* reset value is 0x4 */
+	.cmd2iclkout	= 0x00,
+
+};
+
+static struct emif_regs ddr2_emif0_regs = {
+	.sdram_config		= 0x43801A3A,
+	.ref_ctrl		= 0x10000C30,
+	.sdram_tim1		= 0x0AAB15E2,
+	.sdram_tim2		= 0x423631D2,
+	.sdram_tim3		= 0x0080032F,
+	.emif_ddr_phy_ctlr_1	= 0x0, /* depend on cpu rev, set later */
+};
+
+static struct emif_regs ddr2_emif1_regs = {
+	.sdram_config		= 0x43801A3A,
+	.ref_ctrl		= 0x10000C30,
+	.sdram_tim1		= 0x0AAB15E2,
+	.sdram_tim2		= 0x423631D2,
+	.sdram_tim3		= 0x0080032F,
+	.emif_ddr_phy_ctlr_1	= 0x0, /* depend on cpu rev, set later */
+};
+#endif
+
+/*
+ * DDR3 related definitions
+ */
+
+#if defined(CONFIG_TI816X_DDR_PLL_400)
+#define RD_DQS		0x03B
+#define WR_DQS		0x0A6
+#define RD_DQS_GATE	0x12A
+#define EMIF_SDCFG	0x62A41032
+#define EMIF_SDREF	0x10000C30
+#define EMIF_TIM1	0x0CCCE524
+#define EMIF_TIM2	0x30308023
+#define EMIF_TIM3	0x009F82CF
+#define EMIF_PHYCFG	0x0000010B
+#elif defined(CONFIG_TI816X_DDR_PLL_531)
+#define RD_DQS		0x039
+#define WR_DQS		0x0B4
+#define RD_DQS_GATE	0x13D
+#define EMIF_SDCFG	0x62A51832
+#define EMIF_SDREF	0x1000102E
+#define EMIF_TIM1	0x0EF136AC
+#define EMIF_TIM2	0x30408063
+#define EMIF_TIM3	0x009F83AF
+#define EMIF_PHYCFG	0x0000010C
+#elif defined(CONFIG_TI816X_DDR_PLL_675)
+#define RD_DQS		0x039
+#define WR_DQS		0x091
+#define RD_DQS_GATE	0x196
+#define EMIF_SDCFG	0x62A63032
+#define EMIF_SDREF	0x10001491
+#define EMIF_TIM1	0x13358875
+#define EMIF_TIM2	0x5051806C
+#define EMIF_TIM3	0x009F84AF
+#define EMIF_PHYCFG	0x0000010F
+#elif defined(CONFIG_TI816X_DDR_PLL_796)
+#define RD_DQS		0x035
+#define WR_DQS		0x093
+#define RD_DQS_GATE	0x1B3
+#define EMIF_SDCFG	0x62A73832
+#define EMIF_SDREF	0x10001841
+#define EMIF_TIM1	0x1779C9FE
+#define EMIF_TIM2	0x50608074
+#define EMIF_TIM3	0x009F857F
+#define EMIF_PHYCFG	0x00000110
+#endif
+
+static struct ddr_data ddr3_data = {
+	.datardsratio0		= ((RD_DQS<<10) | (RD_DQS<<0)),
+	.datawdsratio0		= ((WR_DQS<<10) | (WR_DQS<<0)),
+	.datawiratio0		= ((0x20<<10) | 0x20<<0),
+	.datagiratio0		= ((0x20<<10) | 0x20<<0),
+	.datafwsratio0		= ((RD_DQS_GATE<<10) | (RD_DQS_GATE<<0)),
+	.datawrsratio0		= (((WR_DQS+0x40)<<10) | ((WR_DQS+0x40)<<0)),
+	.datauserank0delay	= 0x1,
+	.datadldiff0		= 0x0, /* depend on cpu rev, set later */
+};
+
+static const struct cmd_control ddr3_ctrl = {
+	.cmd0csratio	= 0x100,
+	.cmd0dldiff	= 0x004, /* reset value is 0x4 */
+	.cmd0iclkout	= 0x001,
+
+	.cmd1csratio	= 0x100,
+	.cmd1dldiff	= 0x004, /* reset value is 0x4 */
+	.cmd1iclkout	= 0x001,
+
+	.cmd2csratio	= 0x100,
+	.cmd2dldiff	= 0x004, /* reset value is 0x4 */
+	.cmd2iclkout	= 0x001,
+};
+
+static const struct emif_regs ddr3_emif0_regs = {
+	.sdram_config		= EMIF_SDCFG,
+	.ref_ctrl		= EMIF_SDREF,
+	.sdram_tim1		= EMIF_TIM1,
+	.sdram_tim2		= EMIF_TIM2,
+	.sdram_tim3		= EMIF_TIM3,
+	.emif_ddr_phy_ctlr_1	= EMIF_PHYCFG,
+};
+
+static const struct emif_regs ddr3_emif1_regs = {
+	.sdram_config		= EMIF_SDCFG,
+	.ref_ctrl		= EMIF_SDREF,
+	.sdram_tim1		= EMIF_TIM1,
+	.sdram_tim2		= EMIF_TIM2,
+	.sdram_tim3		= EMIF_TIM3,
+	.emif_ddr_phy_ctlr_1	= EMIF_PHYCFG,
+};
+
+void set_uart_mux_conf(void) {}
+
+void set_mux_conf_regs(void)
+{
+	configure_module_pin_mux(mmc_pin_mux);
+}
+
+void sdram_init(void)
+{
+	config_dmm(&evm_lisa_map_regs);
+
+#ifdef CONFIG_TI816X_EVM_DDR2
+	ddr2_data.datadldiff0 = (get_cpu_rev() == 0x1 ? 0x0 : 0xF);
+	ddr2_ctrl.cmd0dldiff = (get_cpu_rev() == 0x1 ? 0x0 : 0xF);
+	ddr2_ctrl.cmd1dldiff = (get_cpu_rev() == 0x1 ? 0x0 : 0xF);
+	ddr2_ctrl.cmd2dldiff = (get_cpu_rev() == 0x1 ? 0x0 : 0xF);
+
+	if (CONFIG_TI816X_USE_EMIF0) {
+		ddr2_emif0_regs.emif_ddr_phy_ctlr_1 =
+			(get_cpu_rev() == 0x1 ? 0x0000010B : 0x0000030B);
+		config_ddr(0, 0, &ddr2_data, &ddr2_ctrl, &ddr2_emif0_regs, 0);
+	}
+
+	if (CONFIG_TI816X_USE_EMIF1) {
+		ddr2_emif1_regs.emif_ddr_phy_ctlr_1 =
+			(get_cpu_rev() == 0x1 ? 0x0000010B : 0x0000030B);
+		config_ddr(1, 0, &ddr2_data, &ddr2_ctrl, &ddr2_emif1_regs, 1);
+	}
+#endif
+
+#ifdef CONFIG_TI816X_EVM_DDR3
+	ddr3_data.datadldiff0 = (get_cpu_rev() == 0x1 ? 0x0 : 0xF);
+
+	if (CONFIG_TI816X_USE_EMIF0)
+		config_ddr(0, 0, &ddr3_data, &ddr3_ctrl, &ddr3_emif0_regs, 0);
+
+	if (CONFIG_TI816X_USE_EMIF1)
+		config_ddr(1, 0, &ddr3_data, &ddr3_ctrl, &ddr3_emif1_regs, 1);
+#endif
+}
+#endif /* CONFIG_SPL_BUILD */
diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index 2f7d93b..23a78c1 100644
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -208,23 +208,6 @@ int board_phy_config(struct phy_device *phydev)
 }
 
 #if defined(CONFIG_VIDEO_IPUV3)
-static void enable_hdmi(void)
-{
-	struct hdmi_regs *hdmi	= (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-	u8 reg;
-	reg = readb(&hdmi->phy_conf0);
-	reg |= HDMI_PHY_CONF0_PDZ_MASK;
-	writeb(reg, &hdmi->phy_conf0);
-
-	udelay(3000);
-	reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
-	writeb(reg, &hdmi->phy_conf0);
-	udelay(3000);
-	reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
-	writeb(reg, &hdmi->phy_conf0);
-	writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
-}
-
 static struct fb_videomode const hdmi = {
 	.name           = "HDMI",
 	.refresh        = 60,
@@ -250,7 +233,7 @@ int board_video_skip(void)
 	if (ret)
 		printf("HDMI cannot be configured: %d\n", ret);
 
-	enable_hdmi();
+	imx_enable_hdmi_phy();
 
 	return ret;
 }
@@ -258,33 +241,14 @@ int board_video_skip(void)
 static void setup_display(void)
 {
 	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-	struct hdmi_regs *hdmi	= (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
 	int reg;
 
-	/* Turn on IPU clock */
-	reg = readl(&mxc_ccm->CCGR3);
-	reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET;
-	writel(reg, &mxc_ccm->CCGR3);
-
-	/* Turn on HDMI PHY clock */
-	reg = readl(&mxc_ccm->CCGR2);
-	reg |=  MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK
-		| MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
-	writel(reg, &mxc_ccm->CCGR2);
-
-	/* clear HDMI PHY reset */
-	writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
+	enable_ipu_clock();
+	imx_setup_hdmi();
 
 	reg = readl(&mxc_ccm->chsccdr);
-	reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK
-		| MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK
-		| MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
 	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
-		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)
-	      | (CHSCCDR_PODF_DIVIDE_BY_3
-		<< MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
-	      | (CHSCCDR_IPU_PRE_CLK_540M_PFD
-		<< MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
 	writel(reg, &mxc_ccm->chsccdr);
 }
 #endif /* CONFIG_VIDEO_IPUV3 */