summaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
authorPriyanka Jain <Priyanka.Jain@freescale.com>2013-10-18 17:19:06 +0530
committerYork Sun <yorksun@freescale.com>2013-11-13 12:41:28 -0800
commit062ef1a662ee5b3292805d8fe458f1baead21281 (patch)
treef2bbbc881d2758f57b29c7c800da8b1959664de5 /board
parent2967af6816a2b5b549a3377edf41781a51d00003 (diff)
downloadu-boot-imx-062ef1a662ee5b3292805d8fe458f1baead21281.zip
u-boot-imx-062ef1a662ee5b3292805d8fe458f1baead21281.tar.gz
u-boot-imx-062ef1a662ee5b3292805d8fe458f1baead21281.tar.bz2
powerpc/t104xrdb: Add T1040RDB board support
T1040RDB is Freescale Reference Design Board supporting the T1040 QorIQ Power Architecture™ processor. T1040RDB board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Integrated 8-port Gigabit Ethernet switch - Four 1 Gbps Ethernet controllers - SERDES Connections, 8 lanes supporting: - PCI - SGMII - QSGMII - SATA 2.0 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 1GB 8-bit NAND flash - NOR: 128MB 16-bit NOR Flash - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - CPLD - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Power Supplies - USB - Supports two USB 2.0 ports with integrated PHYs - Two type A ports with 5V@1.5A per port. - SDHC - SDHC/SDXC connector - SPI - On-board 64MB SPI flash - I2C - Devices connected: EEPROM, thermal monitor, VID controller - Other IO - Two Serial ports - ProfiBus port Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> [York Sun: fixed Makefile] Acked-by: York Sun <yorksun@freescale.com>
Diffstat (limited to 'board')
-rw-r--r--board/freescale/t104xrdb/Makefile12
-rw-r--r--board/freescale/t104xrdb/README162
-rw-r--r--board/freescale/t104xrdb/ddr.c132
-rw-r--r--board/freescale/t104xrdb/ddr.h76
-rw-r--r--board/freescale/t104xrdb/law.c32
-rw-r--r--board/freescale/t104xrdb/pci.c23
-rw-r--r--board/freescale/t104xrdb/t104xrdb.c93
-rw-r--r--board/freescale/t104xrdb/t104xrdb.h13
-rw-r--r--board/freescale/t104xrdb/tlb.c107
9 files changed, 650 insertions, 0 deletions
diff --git a/board/freescale/t104xrdb/Makefile b/board/freescale/t104xrdb/Makefile
new file mode 100644
index 0000000..76c0c94
--- /dev/null
+++ b/board/freescale/t104xrdb/Makefile
@@ -0,0 +1,12 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+
+obj-y += t104xrdb.o
+obj-y += ddr.o
+obj-$(CONFIG_PCI) += pci.o
+obj-y += law.o
+obj-y += tlb.o
diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README
new file mode 100644
index 0000000..e8848ee
--- /dev/null
+++ b/board/freescale/t104xrdb/README
@@ -0,0 +1,162 @@
+Overview
+--------
+The T1040RDB is a Freescale reference board that hosts the T1040 SoC
+(and variants). Variants inclued T1042 presonality of T1040, in which
+case T1040RDB can also be called T1042RDB.
+
+T1040 SoC Overview
+------------------
+The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
+processor cores with high-performance data path acceleration architecture
+and network peripheral interfaces required for networking & telecommunications.
+
+The T1040/T1042 SoC includes the following function and features:
+
+ - Four e5500 cores, each with a private 256 KB L2 cache
+ - 256 KB shared L3 CoreNet platform cache (CPC)
+ - Interconnect CoreNet platform
+ - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
+ support
+ - Data Path Acceleration Architecture (DPAA) incorporating acceleration
+ for the following functions:
+ - Packet parsing, classification, and distribution
+ - Queue management for scheduling, packet sequencing, and congestion
+ management
+ - Cryptography Acceleration (SEC 5.0)
+ - RegEx Pattern Matching Acceleration (PME 2.2)
+ - IEEE Std 1588 support
+ - Hardware buffer management for buffer allocation and deallocation
+ - Ethernet interfaces
+ - Integrated 8-port Gigabit Ethernet switch (T1040 only)
+ - Four 1 Gbps Ethernet controllers
+ - Two RGMII interfaces or one RGMII and one MII interfaces
+ - High speed peripheral interfaces
+ - Four PCI Express 2.0 controllers running at up to 5 GHz
+ - Two SATA controllers supporting 1.5 and 3.0 Gb/s operation
+ - Upto two QSGMII interface
+ - Upto six SGMII interface supporting 1000 Mbps
+ - One SGMII interface supporting upto 2500 Mbps
+ - Additional peripheral interfaces
+ - Two USB 2.0 controllers with integrated PHY
+ - SD/eSDHC/eMMC
+ - eSPI controller
+ - Four I2C controllers
+ - Four UARTs
+ - Four GPIO controllers
+ - Integrated flash controller (IFC)
+ - LCD and HDMI interface (DIU) with 12 bit dual data rate
+ - TDM interface
+ - Multicore programmable interrupt controller (PIC)
+ - Two 8-channel DMA engines
+ - Single source clocking implementation
+ - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
+
+T1040 SoC Personalities
+-------------------------
+
+T1022 Personality:
+T1022 is a reduced personality of T1040 with less core/clusters.
+
+T1042 Personality:
+T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit
+Ethernet switch. Rest of the blocks are same as T1040
+
+
+T1040RDB board Overview
+-------------------------
+ - SERDES Connections, 8 lanes information:
+ 1: None
+ 2: SGMII
+ 3: QSGMII
+ 4: QSGMII
+ 5: PCIe1 x1 slot
+ 6: mini PCIe connector
+ 7: mini PCIe connector
+ 8: SATA connector
+ - DDR Controller
+ - Supports rates of up to 1600 MHz data-rate
+ - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types.
+ - IFC/Local Bus
+ - NAND flash: 1GB 8-bit NAND flash
+ - NOR: 128MB 16-bit NOR Flash
+ - Ethernet
+ - Two on-board RGMII 10/100/1G ethernet ports.
+ - CPLD
+ - Clocks
+ - System and DDR clock (SYSCLK, “DDRCLK”)
+ - SERDES clocks
+ - Power Supplies
+ - USB
+ - Supports two USB 2.0 ports with integrated PHYs
+ - Two type A ports with 5V@1.5A per port.
+ - SDHC
+ - SDHC/SDXC connector
+ - SPI
+ - On-board 64MB SPI flash
+ - Other IO
+ - Two Serial ports
+ - Four I2C ports
+
+Memory map
+-----------
+The addresses in brackets are physical addresses.
+
+Start Address End Address Description Size
+0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB
+0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
+0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
+0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB
+0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
+0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
+0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
+0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
+0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
+0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
+0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
+0xC_3000_0000 0xC_3FFF_FFFF PCI Express 4 Mem Space 256MB
+0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB
+0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB
+0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB
+0x0_0000_0000 0x0_ffff_ffff DDR 2GB
+
+
+NOR Flash memory Map
+---------------------
+ Start End Definition Size
+0xEFF80000 0xEFFFFFFF u-boot (current bank) 512KB
+0xEFF60000 0xEFF7FFFF u-boot env (current bank) 128KB
+0xEFF40000 0xEFF5FFFF FMAN Ucode (current bank) 128KB
+0xED300000 0xEFF3FFFF rootfs (alt bank) 44MB + 256KB
+0xEC800000 0xEC8FFFF Hardware device tree (alt bank) 1MB
+0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
+0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
+0xEBF80000 0xEBFFFFFF u-boot (alt bank) 512KB
+0xEBF60000 0xEBF7FFFF u-boot env (alt bank) 128KB
+0xEBF40000 0xEBF5FFFF FMAN ucode (alt bank) 128KB
+0xE9300000 0xEBF3FFFF rootfs (current bank) 44MB + 256KB
+0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB
+0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
+0xE8000000 0xE801FFFF RCW (current bank) 128KB
+
+
+Various Software configurations/environment variables/commands
+--------------------------------------------------------------
+The below commands apply to the board
+
+1. U-boot environment variable hwconfig
+ The default hwconfig is:
+ hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1:
+ dr_mode=host,phy_type=utmi
+ Note: For USB gadget set "dr_mode=peripheral"
+
+2. FMAN Ucode versions
+ fsl_fman_ucode_t1040.bin
+
+3. Switching to alternate bank
+ Commands for switching to alternate bank.
+
+ 1. To change from vbank0 to vbank4
+ => qixis_reset altbank (it will boot using vbank4)
+
+ 2.To change from vbank4 to vbank0
+ => qixis reset (it will boot using vbank0)
diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c
new file mode 100644
index 0000000..8f58dd6
--- /dev/null
+++ b/board/freescale/t104xrdb/ddr.c
@@ -0,0 +1,132 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+ unsigned int controller_number,
+ unsigned int dimm_number)
+{
+ const char dimm_model[] = "RAW timing DDR";
+
+ if ((controller_number == 0) && (dimm_number == 0)) {
+ memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+ memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+ memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+ }
+
+ return 0;
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ pbsp = udimms[0];
+
+ /* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks &&
+ (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay =
+ pbsp->write_data_delay;
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ popts->twot_en = pbsp->force_2t;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found\n");
+ printf("for data rate %lu MT/s\n", ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->cpo_override = pbsp_highest->cpo;
+ popts->write_data_delay = pbsp_highest->write_data_delay;
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ popts->twot_en = pbsp_highest->force_2t;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+ "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
+ "wrlvl_ctrl_3 0x%x\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+ pbsp->wrlvl_ctl_3);
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * rtt and rtt_wr override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ puts(" DDR: ");
+ return dram_size;
+}
diff --git a/board/freescale/t104xrdb/ddr.h b/board/freescale/t104xrdb/ddr.h
new file mode 100644
index 0000000..9276b59
--- /dev/null
+++ b/board/freescale/t104xrdb/ddr.h
@@ -0,0 +1,76 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+
+dimm_params_t ddr_raw_timing = {
+ .n_ranks = 2,
+ .rank_density = 2147483648u,
+ .capacity = 4294967296u,
+ .primary_sdram_width = 64,
+ .ec_sdram_width = 8,
+ .registered_dimm = 0,
+ .mirrored_dimm = 1,
+ .n_row_addr = 15,
+ .n_col_addr = 10,
+ .n_banks_per_sdram_device = 8,
+ .edc_config = 2, /* ECC */
+ .burst_lengths_bitmask = 0x0c,
+
+ .tckmin_x_ps = 1071,
+ .caslat_x = 0x2fe << 4, /* 5,6,7,8,9,10,11,13 */
+ .taa_ps = 13910,
+ .twr_ps = 15000,
+ .trcd_ps = 13910,
+ .trrd_ps = 6000,
+ .trp_ps = 13910,
+ .tras_ps = 34000,
+ .trc_ps = 48910,
+ .trfc_ps = 260000,
+ .twtr_ps = 7500,
+ .trtp_ps = 7500,
+ .refresh_rate_ps = 7800000,
+ .tfaw_ps = 35000,
+};
+
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2t;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+ {2, 1066, 4, 8, 4, 0x05070609, 0x08090a08, 0xff, 2, 0},
+ {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
+ {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0},
+ {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0},
+ {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0},
+ {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+#endif
diff --git a/board/freescale/t104xrdb/law.c b/board/freescale/t104xrdb/law.c
new file mode 100644
index 0000000..2362d43
--- /dev/null
+++ b/board/freescale/t104xrdb/law.c
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifndef CONFIG_SYS_NO_FLASH
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE_PHYS
+ SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t104xrdb/pci.c b/board/freescale/t104xrdb/pci.c
new file mode 100644
index 0000000..c53e3b7
--- /dev/null
+++ b/board/freescale/t104xrdb/pci.c
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c
new file mode 100644
index 0000000..6e29d64
--- /dev/null
+++ b/board/freescale/t104xrdb/t104xrdb.c
@@ -0,0 +1,93 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "t104xrdb.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ struct cpu_type *cpu = gd->arch.cpu;
+
+ printf("Board: %sRDB\n", cpu->name);
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+#ifdef CONFIG_SYS_FLASH_BASE
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+#endif
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+#endif
+}
diff --git a/board/freescale/t104xrdb/t104xrdb.h b/board/freescale/t104xrdb/t104xrdb.h
new file mode 100644
index 0000000..e7cc0c7
--- /dev/null
+++ b/board/freescale/t104xrdb/t104xrdb.h
@@ -0,0 +1,13 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __T104x_RDB_H__
+#define __T104x_RDB_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
diff --git a/board/freescale/t104xrdb/tlb.c b/board/freescale/t104xrdb/tlb.c
new file mode 100644
index 0000000..84f97a4
--- /dev/null
+++ b/board/freescale/t104xrdb/tlb.c
@@ -0,0 +1,107 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /*
+ * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
+ * SRAM is at 0xfffc0000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_256K, 1),
+#else
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 5, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 7, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 8, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 9, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+ /*
+ * *I*G - NAND
+ * entry 14 and 15 has been used hard coded, they will be disabled
+ * in cpu_init_f, so we use entry 16 for nand.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE
+ SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 11, BOOKE_PAGESZ_256K, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);