ENGR00333317 imx: mx6sxsabreauto: Add BSP support for AI board

Create mx6sx sabreauto BSP file and configurations. The devices below
have been supported:

1. SD/MMC/eMMC on SDA/SDB (base board) sockets
2. USB OTG port and USB HOST port (base board)
3. NAND flash
4. QuadSPI flash on QSPI1
5. I2C
6. PMIC PFUZE100
7. Onboard ethernet chip on ENET2
8. Splash screen on LVDS

Signed-off-by: Ye.Li <B37916@freescale.com>

4 files changed, 1200 insertions, 0 deletions

diff --git a/board/freescale/mx6sxsabreauto/Makefile b/board/freescale/mx6sxsabreauto/Makefile
new file mode 100644
index 0000000..db01364
--- /dev/null
+++ b/board/freescale/mx6sxsabreauto/Makefile
@@ -0,0 +1,10 @@
+# (C) Copyright 2014 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := mx6sxsabreauto.o
+
+extra-$(CONFIG_USE_PLUGIN) :=  plugin.bin
+$(obj)/plugin.bin: $(obj)/plugin.o
+	$(OBJCOPY) -O binary --gap-fill 0xff $< $@
diff --git a/board/freescale/mx6sxsabreauto/imximage.cfg b/board/freescale/mx6sxsabreauto/imximage.cfg
new file mode 100644
index 0000000..d431a2d
--- /dev/null
+++ b/board/freescale/mx6sxsabreauto/imximage.cfg
@@ -0,0 +1,161 @@
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+#ifdef CONFIG_SYS_BOOT_QSPI
+BOOT_FROM	qspi
+#elif defined(CONFIG_SYS_BOOT_EIMNOR)
+BOOT_FROM	nor
+#else
+BOOT_FROM	sd
+#endif
+
+#ifdef CONFIG_USE_PLUGIN
+/*PLUGIN    plugin-binary-file    IRAM_FREE_START_ADDR*/
+PLUGIN	board/freescale/mx6sxsabreauto/plugin.bin 0x00907000
+#else
+
+#ifdef CONFIG_SECURE_BOOT
+CSF 0x2000
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+/* Enable all clocks */
+DATA 4 0x020c4068 0xffffffff
+DATA 4 0x020c406c 0xffffffff
+DATA 4 0x020c4070 0xffffffff
+DATA 4 0x020c4074 0xffffffff
+DATA 4 0x020c4078 0xffffffff
+DATA 4 0x020c407c 0xffffffff
+DATA 4 0x020c4080 0xffffffff
+DATA 4 0x020c4084 0xffffffff
+
+/* IOMUX */
+/* DDR IO TYPE */
+DATA 4 0x020e0618 0x000c0000
+DATA 4 0x020e05fc 0x00000000
+
+/* CLOCK */
+DATA 4 0x020e032c 0x00000030
+
+/* ADDRESS */
+DATA 4 0x020e0300 0x00000030
+DATA 4 0x020e02fc 0x00000030
+DATA 4 0x020e05f4 0x00000030
+
+/* CONTROL */
+DATA 4 0x020e0340 0x00000030
+
+DATA 4 0x020e0320 0x00000000
+DATA 4 0x020e0310 0x00000030
+DATA 4 0x020e0314 0x00000030
+DATA 4 0x020e0614 0x00000030
+
+/* DATA STROBE */
+DATA 4 0x020e05f8 0x00020000
+DATA 4 0x020e0330 0x00000030
+DATA 4 0x020e0334 0x00000030
+DATA 4 0x020e0338 0x00000030
+DATA 4 0x020e033c 0x00000030
+
+/* DATA */
+DATA 4 0x020e0608 0x00020000
+DATA 4 0x020e060c 0x00000030
+DATA 4 0x020e0610 0x00000030
+DATA 4 0x020e061c 0x00000030
+DATA 4 0x020e0620 0x00000030
+DATA 4 0x020e02ec 0x00000030
+DATA 4 0x020e02f0 0x00000030
+DATA 4 0x020e02f4 0x00000030
+DATA 4 0x020e02f8 0x00000030
+
+/* Calibrations */
+/* ZQ */
+DATA 4 0x021b0800 0xa1390003
+/* write leveling */
+DATA 4 0x021b080c 0x002C003D
+DATA 4 0x021b0810 0x00110046
+
+/* DQS Read Gate */
+DATA 4 0x021b083c 0x4160016C
+DATA 4 0x021b0840 0x013C016C
+
+/* Read/Write Delay */
+DATA 4 0x021b0848 0x46424446
+DATA 4 0x021b0850 0x3A3C3C3A
+
+DATA 4 0x021b08c0 0x2492244A
+
+/* read data bit delay */
+DATA 4 0x021b081c 0x33333333
+DATA 4 0x021b0820 0x33333333
+DATA 4 0x021b0824 0x33333333
+DATA 4 0x021b0828 0x33333333
+
+/* Complete calibration by forced measurment */
+DATA 4 0x021b08b8 0x00000800
+
+/* MMDC init */
+/* in DDR3, 64-bit mode, only MMDC0 is initiated */
+DATA 4 0x021b0004 0x0002002d
+DATA 4 0x021b0008 0x00333030
+DATA 4 0x021b000c 0x676b52f3
+DATA 4 0x021b0010 0xb66d8b63
+DATA 4 0x021b0014 0x01ff00db
+DATA 4 0x021b0018 0x00011740
+DATA 4 0x021b001c 0x00008000
+DATA 4 0x021b002c 0x000026d2
+DATA 4 0x021b0030 0x006b1023
+DATA 4 0x021b0040 0x0000007f
+DATA 4 0x021b0000 0x85190000
+
+/* Initialize CS0: MT41K256M16HA-125 */
+/* MR2 */
+DATA 4 0x021b001c 0x04008032
+/* MR3 */
+DATA 4 0x021b001c 0x00008033
+/* MR1 */
+DATA 4 0x021b001c 0x00068031
+/* MR0 */
+DATA 4 0x021b001c 0x05208030
+/* DDR device ZQ calibration */
+DATA 4 0x021b001c 0x04008040
+
+/* final DDR setup, before operation start */
+DATA 4 0x021b0020 0x00000800
+DATA 4 0x021b0818 0x00022227
+DATA 4 0x021b0004 0x0002556d
+DATA 4 0x021b0404 0x00011006
+DATA 4 0x021b001c 0x00000000
+
+#endif
diff --git a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
new file mode 100644
index 0000000..5785255
--- /dev/null
+++ b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
@@ -0,0 +1,886 @@
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/io.h>
+#include <linux/sizes.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/crm_regs.h>
+#ifdef CONFIG_SYS_I2C_MXC
+#include <i2c.h>
+#include <asm/imx-common/mxc_i2c.h>
+#endif
+#ifdef CONFIG_MXC_RDC
+#include <asm/imx-common/rdc-sema.h>
+#include <asm/arch/imx-rdc.h>
+#endif
+
+#ifdef CONFIG_VIDEO_MXS
+#include <linux/fb.h>
+#include <mxsfb.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_SPEED_HIGH   |                                   \
+	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
+
+#define ENET_CLK_PAD_CTRL  (PAD_CTL_SPEED_MED | \
+	PAD_CTL_DSE_120ohm   | PAD_CTL_SRE_FAST)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
+	PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE |            \
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
+	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |			\
+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define LCD_PAD_CTRL    (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
+	PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm)
+
+#define BUTTON_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE | \
+	PAD_CTL_PUS_22K_UP | PAD_CTL_DSE_40ohm)
+
+#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
+#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
+			PAD_CTL_SRE_FAST)
+#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
+
+
+#ifdef CONFIG_SYS_I2C_MXC
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C2 for PMIC */
+struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6SX_PAD_GPIO1_IO02__I2C2_SCL | PC,
+		.gpio_mode = MX6SX_PAD_GPIO1_IO02__GPIO1_IO_2 | PC,
+		.gp = IMX_GPIO_NR(1, 2),
+	},
+	.sda = {
+		.i2c_mode = MX6SX_PAD_GPIO1_IO03__I2C2_SDA | PC,
+		.gpio_mode = MX6SX_PAD_GPIO1_IO03__GPIO1_IO_3 | PC,
+		.gp = IMX_GPIO_NR(1, 3),
+	},
+};
+
+/* I2C3 */
+struct i2c_pads_info i2c_pad_info3 = {
+	.scl = {
+		.i2c_mode = MX6SX_PAD_KEY_COL4__I2C3_SCL | PC,
+		.gpio_mode = MX6SX_PAD_KEY_COL4__GPIO2_IO_14 | PC,
+		.gp = IMX_GPIO_NR(2, 14),
+	},
+	.sda = {
+		.i2c_mode = MX6SX_PAD_KEY_ROW4__I2C3_SDA | PC,
+		.gpio_mode = MX6SX_PAD_KEY_ROW4__GPIO2_IO_19 | PC,
+		.gp = IMX_GPIO_NR(2, 19),
+	},
+};
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6SX_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6SX_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6SX_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/* CD pin */
+	MX6SX_PAD_USB_H_DATA__GPIO7_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+
+	/* RST_B, used for power reset cycle */
+	MX6SX_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6SX_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/* CD pin */
+	MX6SX_PAD_USB_H_STROBE__GPIO7_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6SX_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const fec2_pads[] = {
+	MX6SX_PAD_ENET1_MDC__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_ENET1_MDIO__ENET2_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec(int fec_id)
+{
+	if (0 == fec_id)
+		imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+	else
+		imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads));
+}
+#endif
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_QSPI
+
+#define QSPI_PAD_CTRL1	\
+		(PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \
+		 PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm)
+
+static iomux_v3_cfg_t const quadspi_pads[] = {
+	MX6SX_PAD_QSPI1A_SS0_B__QSPI1_A_SS0_B   | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1A_SCLK__QSPI1_A_SCLK     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1A_DATA0__QSPI1_A_DATA_0  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1A_DATA1__QSPI1_A_DATA_1	| MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1A_DATA2__QSPI1_A_DATA_2  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1A_DATA3__QSPI1_A_DATA_3  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B   | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1B_SCLK__QSPI1_B_SCLK     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1B_DATA2__QSPI1_B_DATA_2  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+	MX6SX_PAD_QSPI1B_DATA3__QSPI1_B_DATA_3  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
+};
+
+int board_qspi_init(void)
+{
+	/* Set the iomux */
+	imx_iomux_v3_setup_multiple_pads(quadspi_pads, ARRAY_SIZE(quadspi_pads));
+
+	/* Set the clock */
+	enable_qspi_clk(0);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_SYS_USE_NAND
+iomux_v3_cfg_t gpmi_pads[] = {
+	MX6SX_PAD_NAND_CLE__RAWNAND_CLE		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_ALE__RAWNAND_ALE		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_WP_B__RAWNAND_WP_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_READY_B__RAWNAND_READY_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL0),
+	MX6SX_PAD_NAND_CE0_B__RAWNAND_CE0_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_RE_B__RAWNAND_RE_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_WE_B__RAWNAND_WE_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_DATA00__RAWNAND_DATA00	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_DATA01__RAWNAND_DATA01	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_DATA02__RAWNAND_DATA02	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_DATA03__RAWNAND_DATA03	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_DATA04__RAWNAND_DATA04	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_DATA05__RAWNAND_DATA05	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_DATA06__RAWNAND_DATA06	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6SX_PAD_NAND_DATA07__RAWNAND_DATA07	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+};
+
+static void setup_gpmi_nand(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	/* config gpmi nand iomux */
+	imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
+
+	/* config gpmi and bch clock to 100 MHz */
+	clrsetbits_le32(&mxc_ccm->cs2cdr,
+			MXC_CCM_CS2CDR_QSPI2_CLK_PODF_MASK |
+			MXC_CCM_CS2CDR_QSPI2_CLK_PRED_MASK |
+			MXC_CCM_CS2CDR_QSPI2_CLK_SEL_MASK,
+			MXC_CCM_CS2CDR_QSPI2_CLK_PODF(0) |
+			MXC_CCM_CS2CDR_QSPI2_CLK_PRED(3) |
+			MXC_CCM_CS2CDR_QSPI2_CLK_SEL(3));
+
+	/* enable gpmi and bch clock gating */
+	setbits_le32(&mxc_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+	/* enable apbh clock gating */
+	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+#endif
+
+
+#ifdef CONFIG_FSL_ESDHC
+static struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC3_BASE_ADDR},
+	{USDHC4_BASE_ADDR},
+};
+
+#define USDHC3_CD_GPIO	IMX_GPIO_NR(7, 10)
+#define USDHC3_RST_GPIO	IMX_GPIO_NR(2, 11)
+#define USDHC4_CD_GPIO	IMX_GPIO_NR(7, 11)
+
+int mmc_get_env_devno(void)
+{
+	u32 soc_sbmr = readl(SRC_BASE_ADDR + 0x4);
+	int dev_no;
+	u32 bootsel;
+
+	bootsel = (soc_sbmr & 0x000000FF) >> 6 ;
+
+	/* If not boot from sd/mmc, use default value */
+	if (bootsel != 1)
+		return CONFIG_SYS_MMC_ENV_DEV;
+
+	/* BOOT_CFG2[3] and BOOT_CFG2[4] */
+	dev_no = (soc_sbmr & 0x00001800) >> 11;
+
+	/* need ubstract 1 to map to the mmc device id
+	 * see the comments in board_mmc_init function
+	 */
+
+	dev_no -= 2;
+
+	return dev_no;
+}
+
+int mmc_map_to_kernel_blk(int dev_no)
+{
+	return dev_no + 2;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC3_BASE_ADDR:
+		ret = !gpio_get_value(USDHC3_CD_GPIO);
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = !gpio_get_value(USDHC4_CD_GPIO);
+		break;
+	}
+
+	return ret;
+
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-boot device node)    (Physical Port)
+	 * mmc0                    USDHC3
+	 * mmc1                    USDHC4
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			gpio_direction_input(USDHC3_CD_GPIO);
+
+			/* Need to set steer to B0 to A*/
+			gpio_direction_output(USDHC3_RST_GPIO, 1);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+			gpio_direction_input(USDHC4_CD_GPIO);
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return 0;
+			}
+
+			if (fsl_esdhc_initialize(bis, &usdhc_cfg[i]))
+				printf("Warning: failed to initialize mmc dev %d\n", i);
+	}
+
+	return 0;
+}
+
+int check_mmc_autodetect(void)
+{
+	char *autodetect_str = getenv("mmcautodetect");
+
+	if ((autodetect_str != NULL) &&
+		(strcmp(autodetect_str, "yes") == 0)) {
+		return 1;
+	}
+
+	return 0;
+}
+
+void board_late_mmc_init(void)
+{
+	char cmd[32];
+	char mmcblk[32];
+	u32 dev_no = mmc_get_env_devno();
+
+	if (!check_mmc_autodetect())
+		return;
+
+	setenv_ulong("mmcdev", dev_no);
+
+	/* Set mmcblk env */
+	sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw",
+		mmc_map_to_kernel_blk(dev_no));
+	setenv("mmcroot", mmcblk);
+
+	sprintf(cmd, "mmc dev %d", dev_no);
+	run_command(cmd, 0);
+}
+
+#endif
+
+#ifdef CONFIG_VIDEO_MXS
+static iomux_v3_cfg_t const lvds_ctrl_pads[] = {
+	/* Use GPIO for Brightness adjustment, duty cycle = period */
+	MX6SX_PAD_SD1_DATA1__GPIO6_IO_3 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const lcd_pads[] = {
+	MX6SX_PAD_LCD1_CLK__LCDIF1_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17 | MUX_PAD_CTRL(LCD_PAD_CTRL),
+	MX6SX_PAD_LCD1_RESET__GPIO3_IO_27 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+
+struct lcd_panel_info_t {
+	unsigned int lcdif_base_addr;
+	int depth;
+	void	(*enable)(struct lcd_panel_info_t const *dev);
+	struct fb_videomode mode;
+};
+
+void do_enable_lvds(struct lcd_panel_info_t const *dev)
+{
+	enable_lcdif_clock(dev->lcdif_base_addr);
+	enable_lvds(dev->lcdif_base_addr);
+
+	imx_iomux_v3_setup_multiple_pads(lvds_ctrl_pads,
+							ARRAY_SIZE(lvds_ctrl_pads));
+
+	/* Set Brightness to high */
+	gpio_direction_output(IMX_GPIO_NR(6, 3) , 1);
+}
+
+void do_enable_parallel_lcd(struct lcd_panel_info_t const *dev)
+{
+	enable_lcdif_clock(dev->lcdif_base_addr);
+
+	imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+
+	/* Power up the LCD */
+	gpio_direction_output(IMX_GPIO_NR(3, 27) , 1);
+}
+
+static struct lcd_panel_info_t const displays[] = {{
+	.lcdif_base_addr = LCDIF2_BASE_ADDR,
+	.depth = 18,
+	.enable	= do_enable_lvds,
+	.mode	= {
+		.name			= "Hannstar-XGA",
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = 0,
+		.vmode          = FB_VMODE_NONINTERLACED
+} }, {
+	.lcdif_base_addr = LCDIF1_BASE_ADDR,
+	.depth = 18,
+	.enable	= do_enable_parallel_lcd,
+	.mode	= {
+		.name			= "Boundary-LCD",
+		.xres           = 800,
+		.yres           = 480,
+		.pixclock       = 29850,
+		.left_margin    = 89,
+		.right_margin   = 164,
+		.upper_margin   = 23,
+		.lower_margin   = 10,
+		.hsync_len      = 10,
+		.vsync_len      = 10,
+		.sync           = 0,
+		.vmode          = FB_VMODE_NONINTERLACED
+} } };
+
+int board_video_skip(void)
+{
+	int i;
+	int ret;
+	char const *panel = getenv("panel");
+	if (!panel) {
+		panel = displays[0].mode.name;
+		printf("No panel detected: default to %s\n", panel);
+		i = 0;
+	} else {
+		for (i = 0; i < ARRAY_SIZE(displays); i++) {
+			if (!strcmp(panel, displays[i].mode.name))
+				break;
+		}
+	}
+	if (i < ARRAY_SIZE(displays)) {
+		ret = mxs_lcd_panel_setup(displays[i].mode, displays[i].depth,
+				    displays[i].lcdif_base_addr);
+		if (!ret) {
+			if (displays[i].enable)
+				displays[i].enable(displays+i);
+			printf("Display: %s (%ux%u)\n",
+			       displays[i].mode.name,
+			       displays[i].mode.xres,
+			       displays[i].mode.yres);
+		} else
+			printf("LCD %s cannot be configured: %d\n",
+			       displays[i].mode.name, ret);
+	} else {
+		printf("unsupported panel %s\n", panel);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+
+	setup_iomux_fec(CONFIG_FEC_ENET_DEV);
+
+	ret = fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV,
+		CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+	if (ret)
+		printf("FEC%d MXC: %s:failed\n", CONFIG_FEC_ENET_DEV, __func__);
+
+	return 0;
+}
+
+static int setup_fec(int fec_id)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;
+	int ret;
+
+	if (0 == fec_id)
+		/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17]*/
+		clrsetbits_le32(&iomuxc_gpr_regs->gpr[1], IOMUX_GPR1_FEC1_MASK, 0);
+	else
+		/* Use 125M anatop REF_CLK1 for ENET2, clear gpr1[14], gpr1[18]*/
+		clrsetbits_le32(&iomuxc_gpr_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, 0);
+
+	ret = enable_fec_anatop_clock(fec_id, ENET_125MHz);
+	if (ret)
+		return ret;
+
+	enable_enet_clock();
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* Enable 1.8V(SEL_1P5_1P8_POS_REG) on Phy control debug reg 0 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	/* rgmii tx clock delay enable */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_PFUZE100_PMIC_I2C
+#define PFUZE100_DEVICEID	0x0
+#define PFUZE100_REVID		0x3
+#define PFUZE100_FABID		0x4
+
+#define PFUZE100_SW1ABVOL	0x20
+#define PFUZE100_SW1ABSTBY	0x21
+#define PFUZE100_SW1ABCONF	0x24
+#define PFUZE100_SW1CVOL	0x2e
+#define PFUZE100_SW1CSTBY	0x2f
+#define PFUZE100_SW1CCONF	0x32
+#define PFUZE100_SW1ABC_SETP(x)	((x - 3000) / 250)
+#define PFUZE100_VGEN5CTL	0x70
+
+/* set all switches APS in normal and PFM mode in standby */
+static int setup_pmic_mode(int chip)
+{
+	unsigned char offset, i, switch_num, value;
+
+	if (!chip) {
+		/* pfuze100 */
+		switch_num = 6;
+		offset = 0x31;
+	} else {
+		/* pfuze200 */
+		switch_num = 4;
+		offset = 0x38;
+	}
+
+	value = 0xc;
+	if (i2c_write(0x8, 0x23, 1, &value, 1)) {
+		printf("Set SW1AB mode error!\n");
+		return -1;
+	}
+
+	for (i = 0; i < switch_num - 1; i++) {
+		if (i2c_write(0x8, offset + i * 7, 1, &value, 1)) {
+			printf("Set switch%x mode error!\n", offset);
+			return -1;
+		}
+	}
+
+	return 0;
+}
+
+static int setup_pmic_voltages(void)
+{
+	unsigned char value, rev_id = 0;
+
+	i2c_set_bus_num(CONFIG_PMIC_I2C_BUS);
+
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_PMIC_I2C_SLAVE);
+	if (!i2c_probe(CONFIG_PMIC_I2C_SLAVE)) {
+		if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_DEVICEID, 1, &value, 1)) {
+			printf("Read device ID error!\n");
+			return -1;
+		}
+		if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_REVID, 1, &rev_id, 1)) {
+			printf("Read Rev ID error!\n");
+			return -1;
+		}
+		printf("Found PFUZE100! deviceid 0x%x, revid 0x%x\n", value, rev_id);
+
+		if (setup_pmic_mode(value & 0xf)) {
+			printf("setup pmic mode error!\n");
+			return -1;
+		}
+		/* set SW1AB standby volatage 0.975V */
+		if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABSTBY, 1, &value, 1)) {
+			printf("Read SW1ABSTBY error!\n");
+			return -1;
+		}
+		value &= ~0x3f;
+		value |= PFUZE100_SW1ABC_SETP(9750);
+		if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABSTBY, 1, &value, 1)) {
+			printf("Set SW1ABSTBY error!\n");
+			return -1;
+		}
+
+		/* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+		if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABCONF, 1, &value, 1)) {
+			printf("Read SW1ABCONFIG error!\n");
+			return -1;
+		}
+		value &= ~0xc0;
+		value |= 0x40;
+		if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABCONF, 1, &value, 1)) {
+			printf("Set SW1ABCONFIG error!\n");
+			return -1;
+		}
+
+		/* set SW1C standby volatage 0.975V */
+		if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CSTBY, 1, &value, 1)) {
+			printf("Read SW1CSTBY error!\n");
+			return -1;
+		}
+		value &= ~0x3f;
+		value |= PFUZE100_SW1ABC_SETP(9750);
+		if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CSTBY, 1, &value, 1)) {
+			printf("Set SW1CSTBY error!\n");
+			return -1;
+		}
+
+		/* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
+		if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CCONF, 1, &value, 1)) {
+			printf("Read SW1CCONFIG error!\n");
+			return -1;
+		}
+		value &= ~0xc0;
+		value |= 0x40;
+		if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CCONF, 1, &value, 1)) {
+			printf("Set SW1CCONFIG error!\n");
+			return -1;
+		}
+
+		/* Enable power of VGEN5 3V3, needed for SD3 */
+		if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_VGEN5CTL, 1, &value, 1)) {
+			printf("Read VGEN5CTL error!\n");
+			return -1;
+		}
+		value &= ~0x1F;
+		value |= 0x1F;
+		if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_VGEN5CTL, 1, &value, 1)) {
+			printf("Set VGEN5CTL error!\n");
+			return -1;
+		}
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_LDO_BYPASS_CHECK
+void ldo_mode_set(int ldo_bypass)
+{
+	unsigned char value;
+	/* switch to ldo_bypass mode */
+	if (ldo_bypass) {
+		/* decrease VDDARM to 1.15V */
+		if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABVOL, 1, &value, 1)) {
+			printf("Read SW1AB error!\n");
+			return;
+		}
+		value &= ~0x3f;
+		value |= PFUZE100_SW1ABC_SETP(11500);
+		if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1ABVOL, 1, &value, 1)) {
+			printf("Set SW1AB error!\n");
+			return;
+		}
+		/* increase VDDSOC to 1.15V */
+		if (i2c_read(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CVOL, 1, &value, 1)) {
+			printf("Read SW1C error!\n");
+			return;
+		}
+		value &= ~0x3f;
+		value |= PFUZE100_SW1ABC_SETP(11500);
+		if (i2c_write(CONFIG_PMIC_I2C_SLAVE, PFUZE100_SW1CVOL, 1, &value, 1)) {
+			printf("Set SW1C error!\n");
+			return;
+		}
+
+		set_anatop_bypass(1);
+		printf("switch to ldo_bypass mode!\n");
+	}
+
+}
+#endif
+#endif
+
+#ifdef CONFIG_MXC_RDC
+static rdc_peri_cfg_t const shared_resources[] = {
+	(RDC_PER_GPIO1 | RDC_DOMAIN(0) | RDC_DOMAIN(1)),
+};
+#endif
+
+int board_early_init_f(void)
+{
+#ifdef CONFIG_MXC_RDC
+	imx_rdc_setup_peripherals(shared_resources, ARRAY_SIZE(shared_resources));
+#endif
+
+#ifdef CONFIG_SYS_AUXCORE_FASTUP
+	arch_auxiliary_core_up(0, CONFIG_SYS_AUXCORE_BOOTDATA);
+#endif
+
+	setup_iomux_uart();
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_SYS_I2C_MXC
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
+#endif
+
+#ifdef	CONFIG_FEC_MXC
+	setup_fec(CONFIG_FEC_ENET_DEV);
+#endif
+
+#ifdef CONFIG_SYS_USE_NAND
+	setup_gpmi_nand();
+#endif
+
+#ifdef CONFIG_QSPI
+	board_qspi_init();
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	{"sda", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
+	{"sdb", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
+	{"qspi1", MAKE_CFGVAL(0x18, 0x00, 0x00, 0x00)},
+	{"nand", MAKE_CFGVAL(0x18, 0x00, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+#ifdef CONFIG_PFUZE100_PMIC_I2C
+	int ret = 0;
+
+	ret = setup_pmic_voltages();
+	if (ret)
+		return -1;
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+	board_late_mmc_init();
+#endif
+
+	return 0;
+}
+
+u32 get_board_rev(void)
+{
+	return get_cpu_rev();
+}
+
+int checkboard(void)
+{
+	puts("Board: MX6SX SABRE AUTO\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_USB_EHCI_MX6
+iomux_v3_cfg_t const usb_otg1_pads[] = {
+	MX6SX_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL)
+};
+
+iomux_v3_cfg_t const usb_host2_pads[] = {
+	MX6SX_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_ehci_hcd_init(int port)
+{
+	switch (port) {
+	case 0:
+		imx_iomux_v3_setup_multiple_pads(usb_otg1_pads,
+			ARRAY_SIZE(usb_otg1_pads));
+		break;
+	case 1:
+		imx_iomux_v3_setup_multiple_pads(usb_host2_pads,
+			ARRAY_SIZE(usb_host2_pads));
+		break;
+	default:
+		printf("MXC USB port %d not yet supported\n", port);
+		return 1;
+	}
+	return 0;
+}
+#endif
diff --git a/board/freescale/mx6sxsabreauto/plugin.S b/board/freescale/mx6sxsabreauto/plugin.S
new file mode 100644
index 0000000..169a852
--- /dev/null
+++ b/board/freescale/mx6sxsabreauto/plugin.S
@@ -0,0 +1,143 @@
+/*
+ * Copyright (C) 2013-2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+
+/* DDR script */
+.macro imx6sx_sabreauto_ddr_setting
+	ldr r0, =IOMUXC_BASE_ADDR
+	ldr r1, =0x000c0000
+	str r1, [r0, #0x618]
+	ldr r1, =0x00000000
+	str r1, [r0, #0x5fc]
+	ldr r1, =0x00000030
+	str r1, [r0, #0x32c]
+
+	ldr r1, =0x00000030
+	str r1, [r0, #0x300]
+	str r1, [r0, #0x2fc]
+	str r1, [r0, #0x5f4]
+	str r1, [r0, #0x340]
+
+	ldr r1, =0x00000000
+	str r1, [r0, #0x320]
+	ldr r1, =0x00000030
+	str r1, [r0, #0x310]
+	str r1, [r0, #0x314]
+	str r1, [r0, #0x614]
+
+	ldr r1, =0x00020000
+	str r1, [r0, #0x5f8]
+	ldr r1, =0x00000030
+	str r1, [r0, #0x330]
+	str r1, [r0, #0x334]
+	str r1, [r0, #0x338]
+	str r1, [r0, #0x33c]
+	ldr r1, =0x00020000
+	str r1, [r0, #0x608]
+	ldr r1, =0x00000030
+	str r1, [r0, #0x60c]
+	str r1, [r0, #0x610]
+	str r1, [r0, #0x61c]
+	str r1, [r0, #0x620]
+	str r1, [r0, #0x2ec]
+	str r1, [r0, #0x2f0]
+	str r1, [r0, #0x2f4]
+	str r1, [r0, #0x2f8]
+
+	ldr r0, =MMDC_P0_BASE_ADDR
+	ldr r2, =0xa1390003
+	str r2, [r0, #0x800]
+	ldr r2, =0x002C003D
+	str r2, [r0, #0x80c]
+	ldr r2, =0x00110046
+	str r2, [r0, #0x810]
+	ldr r2, =0x4160016C
+	str r2, [r0, #0x83c]
+	ldr r2, =0x013C016C
+	str r2, [r0, #0x840]
+	ldr r2, =0x46424446
+	str r2, [r0, #0x848]
+	ldr r2, =0x3A3C3C3A
+	str r2, [r0, #0x850]
+	ldr r2, =0x2492244A
+	str r2, [r0, #0x8c0]
+
+	ldr r2, =0x33333333
+	str r2, [r0, #0x81c]
+	str r2, [r0, #0x820]
+	str r2, [r0, #0x824]
+	str r2, [r0, #0x828]
+
+	ldr r2, =0x00000800
+	str r2, [r0, #0x8b8]
+	ldr r2, =0x0002002d
+	str r2, [r0, #0x004]
+	ldr r2, =0x00333030
+	str r2, [r0, #0x008]
+	ldr r2, =0x676b52f3
+	str r2, [r0, #0x00c]
+	ldr r2, =0xb66d8b63
+	str r2, [r0, #0x010]
+	ldr r2, =0x01ff00db
+	str r2, [r0, #0x014]
+	ldr r2, =0x00011740
+	str r2, [r0, #0x018]
+	ldr r2, =0x00008000
+	str r2, [r0, #0x01c]
+	ldr r2, =0x000026d2
+	str r2, [r0, #0x02c]
+	ldr r2, =0x006b1023
+	str r2, [r0, #0x030]
+	ldr r2, =0x0000007f
+	str r2, [r0, #0x040]
+	ldr r2, =0x85190000
+	str r2, [r0, #0x000]
+	ldr r2, =0x04008032
+	str r2, [r0, #0x01c]
+	ldr r2, =0x00008033
+	str r2, [r0, #0x01c]
+	ldr r2, =0x00068031
+	str r2, [r0, #0x01c]
+	ldr r2, =0x05208030
+	str r2, [r0, #0x01c]
+	ldr r2, =0x04008040
+	str r2, [r0, #0x01c]
+	ldr r2, =0x00000800
+	str r2, [r0, #0x020]
+	ldr r2, =0x00022227
+	str r2, [r0, #0x818]
+	ldr r2, =0x0002556d
+	str r2, [r0, #0x004]
+	ldr r2, =0x00011006
+	str r2, [r0, #0x404]
+	ldr r2, =0x00000000
+	str r2, [r0, #0x01c]
+
+.endm
+
+.macro imx6_clock_gating
+	ldr r0, =CCM_BASE_ADDR
+	ldr r1, =0xffffffff
+	str r1, [r0, #0x068]
+	str r1, [r0, #0x06c]
+	str r1, [r0, #0x070]
+	str r1, [r0, #0x074]
+	str r1, [r0, #0x078]
+	str r1, [r0, #0x07c]
+	str r1, [r0, #0x080]
+	str r1, [r0, #0x084]
+.endm
+
+.macro imx6_qos_setting
+.endm
+
+.macro imx6_ddr_setting
+	imx6sx_sabreauto_ddr_setting
+.endm
+
+/* include the common plugin code here */
+#include <asm/arch/mx6_plugin.S>