Merge branch 'master' of git://www.denx.de/git/u-boot-imx

14 files changed, 1339 insertions, 17 deletions

diff --git a/board/aristainetos/aristainetos.c b/board/aristainetos/aristainetos.c
index 3bfcf5b..06922c0 100644
--- a/board/aristainetos/aristainetos.c
+++ b/board/aristainetos/aristainetos.c
@@ -230,6 +230,12 @@ static iomux_v3_cfg_t const backlight_pads[] = {
 	MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
 };
 
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
+		? (IMX_GPIO_NR(3, 20)) : -1;
+}
+
 static void setup_spi(void)
 {
 	int i;
diff --git a/board/bachmann/ot1200/ot1200.c b/board/bachmann/ot1200/ot1200.c
index acf95cb..2ed8cf7 100644
--- a/board/bachmann/ot1200/ot1200.c
+++ b/board/bachmann/ot1200/ot1200.c
@@ -104,10 +104,25 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs)
 	return (bus == 2 && cs == 0) ? (IMX_GPIO_NR(1, 3)) : -1;
 }
 
+static iomux_v3_cfg_t const feature_pads[] = {
+	/* SD card detect */
+	MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(PAD_CTL_PUS_100K_DOWN),
+
+	/* eMMC soldered? */
+	MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(PAD_CTL_PUS_100K_UP),
+};
+
+static void setup_iomux_features(void)
+{
+	imx_iomux_v3_setup_multiple_pads(feature_pads,
+		ARRAY_SIZE(feature_pads));
+}
+
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
 	setup_iomux_spi();
+	setup_iomux_features();
 
 	return 0;
 }
@@ -126,23 +141,68 @@ static iomux_v3_cfg_t const usdhc3_pads[] = {
 	MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 };
 
+iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
 int board_mmc_getcd(struct mmc *mmc)
 {
-	return 1;
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret;
+
+	if (cfg->esdhc_base == USDHC3_BASE_ADDR) {
+		gpio_direction_input(IMX_GPIO_NR(4, 5));
+		ret = gpio_get_value(IMX_GPIO_NR(4, 5));
+	} else {
+		gpio_direction_input(IMX_GPIO_NR(1, 4));
+		ret = !gpio_get_value(IMX_GPIO_NR(1, 4));
+	}
+
+	return ret;
 }
 
-struct fsl_esdhc_cfg usdhc_cfg[] = {
+struct fsl_esdhc_cfg usdhc_cfg[2] = {
 	{USDHC3_BASE_ADDR},
+	{USDHC4_BASE_ADDR},
 };
 
 int board_mmc_init(bd_t *bis)
 {
+	s32 status = 0;
+	u32 index = 0;
+
 	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-	usdhc_cfg[0].max_bus_width = 8;
+	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 
-	imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+	usdhc_cfg[0].max_bus_width = 8;
+	usdhc_cfg[1].max_bus_width = 4;
+
+	for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
+		switch (index) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) then supported by the board (%d)\n",
+				index + 1, CONFIG_SYS_FSL_USDHC_NUM);
+			return status;
+		}
+
+		status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+	}
 
-	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+	return status;
 }
 
 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
index 82681b1..0206ae8 100644
--- a/board/compulab/cm_fx6/cm_fx6.c
+++ b/board/compulab/cm_fx6/cm_fx6.c
@@ -31,12 +31,12 @@ DECLARE_GLOBAL_DATA_PTR;
 #ifdef CONFIG_DWC_AHSATA
 static int cm_fx6_issd_gpios[] = {
 	/* The order of the GPIOs in the array is important! */
+	CM_FX6_SATA_LDO_EN,
 	CM_FX6_SATA_PHY_SLP,
 	CM_FX6_SATA_NRSTDLY,
 	CM_FX6_SATA_PWREN,
 	CM_FX6_SATA_NSTANDBY1,
 	CM_FX6_SATA_NSTANDBY2,
-	CM_FX6_SATA_LDO_EN,
 };
 
 static void cm_fx6_sata_power(int on)
diff --git a/board/compulab/cm_fx6/spl.c b/board/compulab/cm_fx6/spl.c
index 3948ba2..6fe937b 100644
--- a/board/compulab/cm_fx6/spl.c
+++ b/board/compulab/cm_fx6/spl.c
@@ -235,10 +235,11 @@ static int cm_fx6_spl_dram_init(void)
 
 		spl_mx6s_dram_init(DDR_32BIT_1GB, false);
 		bank1_size = get_ram_size((long int *)PHYS_SDRAM_1, 0x80000000);
-		if (bank1_size == 0x40000000)
-			return 0;
-
+		bank2_size = get_ram_size((long int *)PHYS_SDRAM_2, 0x80000000);
 		if (bank1_size == 0x20000000) {
+			if (bank2_size == 0x20000000)
+				return 0;
+
 			spl_mx6s_dram_init(DDR_32BIT_512MB, true);
 			return 0;
 		}
diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index 0dc0160..42ae6fa 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -27,6 +27,7 @@
 #include <asm/arch/mxc_hdmi.h>
 #include <asm/imx-common/video.h>
 #include <asm/arch/crm_regs.h>
+#include <pca953x.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -116,6 +117,44 @@ static iomux_v3_cfg_t const port_exp[] = {
 	MX6_PAD_SD2_DAT0__GPIO1_IO15		| MUX_PAD_CTRL(NO_PAD_CTRL),
 };
 
+/*Define for building port exp gpio, pin starts from 0*/
+#define PORTEXP_IO_NR(chip, pin) \
+	((chip << 5) + pin)
+
+/*Get the chip addr from a ioexp gpio*/
+#define PORTEXP_IO_TO_CHIP(gpio_nr) \
+	(gpio_nr >> 5)
+
+/*Get the pin number from a ioexp gpio*/
+#define PORTEXP_IO_TO_PIN(gpio_nr) \
+	(gpio_nr & 0x1f)
+
+static int port_exp_direction_output(unsigned gpio, int value)
+{
+	int ret;
+
+	i2c_set_bus_num(2);
+	ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
+	if (ret)
+		return ret;
+
+	ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
+		(1 << PORTEXP_IO_TO_PIN(gpio)),
+		(PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));
+
+	if (ret)
+		return ret;
+
+	ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
+		(1 << PORTEXP_IO_TO_PIN(gpio)),
+		(value << PORTEXP_IO_TO_PIN(gpio)));
+
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
 static void setup_iomux_enet(void)
 {
 	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
@@ -361,3 +400,57 @@ int checkboard(void)
 
 	return 0;
 }
+
+#ifdef CONFIG_USB_EHCI_MX6
+#define USB_HOST1_PWR     PORTEXP_IO_NR(0x32, 7)
+#define USB_OTG_PWR       PORTEXP_IO_NR(0x34, 1)
+
+iomux_v3_cfg_t const usb_otg_pads[] = {
+	MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_ehci_hcd_init(int port)
+{
+	switch (port) {
+	case 0:
+		imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
+			ARRAY_SIZE(usb_otg_pads));
+
+		/*
+		  * Set daisy chain for otg_pin_id on 6q.
+		 *  For 6dl, this bit is reserved.
+		 */
+		imx_iomux_set_gpr_register(1, 13, 1, 0);
+		break;
+	case 1:
+		break;
+	default:
+		printf("MXC USB port %d not yet supported\n", port);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+int board_ehci_power(int port, int on)
+{
+	switch (port) {
+	case 0:
+		if (on)
+			port_exp_direction_output(USB_OTG_PWR, 1);
+		else
+			port_exp_direction_output(USB_OTG_PWR, 0);
+		break;
+	case 1:
+		if (on)
+			port_exp_direction_output(USB_HOST1_PWR, 1);
+		else
+			port_exp_direction_output(USB_HOST1_PWR, 0);
+		break;
+	default:
+		printf("MXC USB port %d not yet supported\n", port);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+#endif
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 81dcd6e..3d81fff 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -51,6 +51,8 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
 
+#define DISP0_PWR_EN	IMX_GPIO_NR(1, 21)
+
 int dram_init(void)
 {
 	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
@@ -141,6 +143,45 @@ iomux_v3_cfg_t const ecspi1_pads[] = {
 	MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
 };
 
+static iomux_v3_cfg_t const rgb_pads[] = {
+	MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DI0_PIN4__IPU1_DI0_PIN04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD1_DAT3__GPIO1_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void enable_rgb(struct display_info_t const *dev)
+{
+	imx_iomux_v3_setup_multiple_pads(rgb_pads, ARRAY_SIZE(rgb_pads));
+	gpio_direction_output(DISP0_PWR_EN, 1);
+}
+
 static struct i2c_pads_info i2c_pad_info1 = {
 	.scl = {
 		.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
@@ -357,6 +398,26 @@ struct display_info_t const displays[] = {{
 		.vsync_len      = 10,
 		.sync           = FB_SYNC_EXT,
 		.vmode          = FB_VMODE_NONINTERLACED
+} }, {
+	.bus	= 0,
+	.addr	= 0,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= NULL,
+	.enable	= enable_rgb,
+	.mode	= {
+		.name           = "SEIKO-WVGA",
+		.refresh        = 60,
+		.xres           = 800,
+		.yres           = 480,
+		.pixclock       = 29850,
+		.left_margin    = 89,
+		.right_margin   = 164,
+		.upper_margin   = 23,
+		.lower_margin   = 10,
+		.hsync_len      = 10,
+		.vsync_len      = 10,
+		.sync           = 0,
+		.vmode          = FB_VMODE_NONINTERLACED
 } } };
 size_t display_count = ARRAY_SIZE(displays);
 
diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c
index a500133..e76c343 100644
--- a/board/freescale/mx6slevk/mx6slevk.c
+++ b/board/freescale/mx6slevk/mx6slevk.c
@@ -52,6 +52,23 @@ static iomux_v3_cfg_t const uart1_pads[] = {
 	MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	/* 8 bit SD */
+	MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT0__USDHC1_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT1__USDHC1_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT2__USDHC1_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT3__USDHC1_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT4__USDHC1_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT5__USDHC1_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT6__USDHC1_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DAT7__USDHC1_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/*CD pin*/
+	MX6_PAD_KEY_ROW7__GPIO_4_7 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
 static iomux_v3_cfg_t const usdhc2_pads[] = {
 	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -59,6 +76,21 @@ static iomux_v3_cfg_t const usdhc2_pads[] = {
 	MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/*CD pin*/
+	MX6_PAD_SD2_DAT7__GPIO_5_0 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/*CD pin*/
+	MX6_PAD_REF_CLK_32K__GPIO_3_22 | MUX_PAD_CTRL(NO_PAD_CTRL),
 };
 
 static iomux_v3_cfg_t const fec_pads[] = {
@@ -109,21 +141,82 @@ static void setup_iomux_fec(void)
 	gpio_set_value(ETH_PHY_RESET, 1);
 }
 
-static struct fsl_esdhc_cfg usdhc_cfg[1] = {
-	{USDHC2_BASE_ADDR},
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(4, 7)
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(5, 0)
+#define USDHC3_CD_GPIO	IMX_GPIO_NR(3, 22)
+
+static struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC1_BASE_ADDR},
+	{USDHC2_BASE_ADDR, 0, 4},
+	{USDHC3_BASE_ADDR, 0, 4},
 };
 
 int board_mmc_getcd(struct mmc *mmc)
 {
-	return 1;	/* Assume boot SD always present */
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = !gpio_get_value(USDHC3_CD_GPIO);
+		break;
+	}
+
+	return ret;
 }
 
 int board_mmc_init(bd_t *bis)
 {
-	imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+	int i, ret;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-boot device node)    (Physical Port)
+	 * mmc0                    USDHC1
+	 * mmc1                    USDHC2
+	 * mmc2                    USDHC3
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+			gpio_direction_input(USDHC1_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			gpio_direction_input(USDHC2_CD_GPIO);
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		case 2:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			gpio_direction_input(USDHC3_CD_GPIO);
+			usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return -EINVAL;
+			}
+
+			ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+			if (ret) {
+				printf("Warning: failed to initialize "
+					"mmc dev %d\n", i);
+				return ret;
+			}
+	}
 
-	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+	return 0;
 }
 
 #ifdef CONFIG_FEC_MXC
diff --git a/board/kosagi/novena/Kconfig b/board/kosagi/novena/Kconfig
new file mode 100644
index 0000000..4ba6399
--- /dev/null
+++ b/board/kosagi/novena/Kconfig
@@ -0,0 +1,18 @@
+if TARGET_KOSAGI_NOVENA
+
+config SYS_CPU
+	default "armv7"
+
+config SYS_BOARD
+	default "novena"
+
+config SYS_VENDOR
+	default "kosagi"
+
+config SYS_SOC
+	default "mx6"
+
+config SYS_CONFIG_NAME
+	default "novena"
+
+endif
diff --git a/board/kosagi/novena/Makefile b/board/kosagi/novena/Makefile
new file mode 100644
index 0000000..6fba177
--- /dev/null
+++ b/board/kosagi/novena/Makefile
@@ -0,0 +1,11 @@
+#
+# Copyright (C) 2014 Marek Vasut <marex@denx.de>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y	:= novena_spl.o
+else
+obj-y	:= novena.o
+endif
diff --git a/board/kosagi/novena/novena.c b/board/kosagi/novena/novena.c
new file mode 100644
index 0000000..6add9e5
--- /dev/null
+++ b/board/kosagi/novena/novena.c
@@ -0,0 +1,340 @@
+/*
+ * Novena board support
+ *
+ * Copyright (C) 2014 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/sata.h>
+#include <asm/imx-common/video.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <input.h>
+#include <ipu_pixfmt.h>
+#include <linux/fb.h>
+#include <linux/input.h>
+#include <malloc.h>
+#include <micrel.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include <stdio_dev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define NOVENA_BUTTON_GPIO	IMX_GPIO_NR(4, 14)
+#define NOVENA_SD_WP		IMX_GPIO_NR(1, 2)
+#define NOVENA_SD_CD		IMX_GPIO_NR(1, 4)
+
+/*
+ * GPIO button
+ */
+#ifdef CONFIG_KEYBOARD
+static struct input_config button_input;
+
+static int novena_gpio_button_read_keys(struct input_config *input)
+{
+	int key = KEY_ENTER;
+	if (gpio_get_value(NOVENA_BUTTON_GPIO))
+		return 0;
+	input_send_keycodes(&button_input, &key, 1);
+	return 1;
+}
+
+static int novena_gpio_button_getc(struct stdio_dev *dev)
+{
+	return input_getc(&button_input);
+}
+
+static int novena_gpio_button_tstc(struct stdio_dev *dev)
+{
+	return input_tstc(&button_input);
+}
+
+static int novena_gpio_button_init(struct stdio_dev *dev)
+{
+	gpio_direction_input(NOVENA_BUTTON_GPIO);
+	input_set_delays(&button_input, 250, 250);
+	return 0;
+}
+
+int drv_keyboard_init(void)
+{
+	int error;
+	struct stdio_dev dev = {
+		.name	= "button",
+		.flags	= DEV_FLAGS_INPUT | DEV_FLAGS_SYSTEM,
+		.start	= novena_gpio_button_init,
+		.getc	= novena_gpio_button_getc,
+		.tstc	= novena_gpio_button_tstc,
+	};
+
+	error = input_init(&button_input, 0);
+	if (error) {
+		debug("%s: Cannot set up input\n", __func__);
+		return -1;
+	}
+	button_input.read_keys = novena_gpio_button_read_keys;
+
+	error = input_stdio_register(&dev);
+	if (error)
+		return error;
+
+	return 0;
+}
+#endif
+
+/*
+ * SDHC
+ */
+#ifdef CONFIG_FSL_ESDHC
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{ USDHC3_BASE_ADDR, 0, 4 },	/* Micro SD */
+	{ USDHC2_BASE_ADDR, 0, 4 },	/* Big SD */
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+	/* There is no CD for a microSD card, assume always present. */
+	if (cfg->esdhc_base == USDHC3_BASE_ADDR)
+		return 1;
+	else
+		return !gpio_get_value(NOVENA_SD_CD);
+}
+
+int board_mmc_getwp(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+	/* There is no WP for a microSD card, assume always read-write. */
+	if (cfg->esdhc_base == USDHC3_BASE_ADDR)
+		return 0;
+	else
+		return gpio_get_value(NOVENA_SD_WP);
+}
+
+
+int board_mmc_init(bd_t *bis)
+{
+	s32 status = 0;
+	int index;
+
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+
+	/* Big SD write-protect and card-detect */
+	gpio_direction_input(NOVENA_SD_WP);
+	gpio_direction_input(NOVENA_SD_CD);
+
+	for (index = 0; index < ARRAY_SIZE(usdhc_cfg); index++) {
+		status = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+		if (status)
+			return status;
+	}
+
+	return status;
+}
+#endif
+
+/*
+ * Video over HDMI
+ */
+#if defined(CONFIG_VIDEO_IPUV3)
+static void enable_hdmi(struct display_info_t const *dev)
+{
+	imx_enable_hdmi_phy();
+}
+
+struct display_info_t const displays[] = {
+	{
+		/* HDMI Output */
+		.bus	= -1,
+		.addr	= 0,
+		.pixfmt	= IPU_PIX_FMT_RGB24,
+		.detect	= detect_hdmi,
+		.enable	= enable_hdmi,
+		.mode	= {
+			.name           = "HDMI",
+			.refresh        = 60,
+			.xres           = 1024,
+			.yres           = 768,
+			.pixclock       = 15385,
+			.left_margin    = 220,
+			.right_margin   = 40,
+			.upper_margin   = 21,
+			.lower_margin   = 7,
+			.hsync_len      = 60,
+			.vsync_len      = 10,
+			.sync           = FB_SYNC_EXT,
+			.vmode          = FB_VMODE_NONINTERLACED
+		}
+	}
+};
+
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+
+	/* Turn on LDB0,IPU,IPU DI0 clocks */
+	setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
+
+	/* set LDB0, LDB1 clk select to 011/011 */
+	clrsetbits_le32(&mxc_ccm->cs2cdr,
+			MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK |
+			MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK,
+			(3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) |
+			(3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET));
+
+	setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
+
+	setbits_le32(&mxc_ccm->chsccdr, CHSCCDR_CLK_SEL_LDB_DI0 <<
+		     MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+
+	writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
+	       IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH |
+	       IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
+	       IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
+	       IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT |
+	       IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
+	       IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT |
+	       IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED |
+	       IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
+	       &iomux->gpr[2]);
+
+	clrsetbits_le32(&iomux->gpr[3], IOMUXC_GPR3_LVDS0_MUX_CTL_MASK,
+			IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
+			IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+}
+#endif
+
+int board_early_init_f(void)
+{
+#if defined(CONFIG_VIDEO_IPUV3)
+	setup_display();
+#endif
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_CMD_SATA
+	setup_sata();
+#endif
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: Novena 4x\n");
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+	return 0;
+}
+
+/* setup board specific PMIC */
+int power_init_board(void)
+{
+	struct pmic *p;
+	u32 reg;
+	int ret;
+
+	power_pfuze100_init(1);
+	p = pmic_get("PFUZE100");
+	if (!p)
+		return -EINVAL;
+
+	ret = pmic_probe(p);
+	if (ret)
+		return ret;
+
+	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
+	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
+
+	/* Set SWBST to 5.0V and enable (for USB) */
+	pmic_reg_read(p, PFUZE100_SWBSTCON1, &reg);
+	reg &= ~(SWBST_MODE_MASK | SWBST_VOL_MASK);
+	reg |= (SWBST_5_00V | SWBST_MODE_AUTO);
+	pmic_reg_write(p, PFUZE100_SWBSTCON1, reg);
+
+	return 0;
+}
+
+/* EEPROM configuration data */
+struct novena_eeprom_data {
+	uint8_t		signature[6];
+	uint8_t		version;
+	uint8_t		reserved;
+	uint32_t	serial;
+	uint8_t		mac[6];
+	uint16_t	features;
+};
+
+int misc_init_r(void)
+{
+	struct novena_eeprom_data data;
+	uchar *datap = (uchar *)&data;
+	const char *signature = "Novena";
+	int ret;
+
+	/* If 'ethaddr' is already set, do nothing. */
+	if (getenv("ethaddr"))
+		return 0;
+
+	/* EEPROM is at bus 2. */
+	ret = i2c_set_bus_num(2);
+	if (ret) {
+		puts("Cannot select EEPROM I2C bus.\n");
+		return 0;
+	}
+
+	/* EEPROM is at address 0x56. */
+	ret = eeprom_read(0x56, 0, datap, sizeof(data));
+	if (ret) {
+		puts("Cannot read I2C EEPROM.\n");
+		return 0;
+	}
+
+	/* Check EEPROM signature. */
+	if (memcmp(data.signature, signature, 6)) {
+		puts("Invalid I2C EEPROM signature.\n");
+		return 0;
+	}
+
+	/* Set ethernet address from EEPROM. */
+	eth_setenv_enetaddr("ethaddr", data.mac);
+
+	return ret;
+}
diff --git a/board/kosagi/novena/novena_spl.c b/board/kosagi/novena/novena_spl.c
new file mode 100644
index 0000000..c4155dd
--- /dev/null
+++ b/board/kosagi/novena/novena_spl.c
@@ -0,0 +1,584 @@
+/*
+ * Novena SPL
+ *
+ * Copyright (C) 2014 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spl.h>
+
+#include <asm/arch/mx6-ddr.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL						\
+	(PAD_CTL_PKE | PAD_CTL_PUE |				\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL						\
+	(PAD_CTL_PKE | PAD_CTL_PUE |				\
+	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL						\
+	(PAD_CTL_PKE | PAD_CTL_PUE |				\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED	  |		\
+	PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)
+
+#define ENET_PHY_CFG_PAD_CTRL					\
+	(PAD_CTL_PKE | PAD_CTL_PUE |				\
+	PAD_CTL_PUS_22K_UP | PAD_CTL_HYS)
+
+#define RGMII_PAD_CTRL						\
+	(PAD_CTL_PKE | PAD_CTL_PUE |				\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define SPI_PAD_CTRL						\
+	(PAD_CTL_HYS |						\
+	PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm     | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL						\
+	(PAD_CTL_PKE | PAD_CTL_PUE |				\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_240ohm  | PAD_CTL_HYS |			\
+	PAD_CTL_ODE)
+
+#define BUTTON_PAD_CTRL						\
+	(PAD_CTL_PKE | PAD_CTL_PUE |				\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED   |		\
+	PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+#define NOVENA_AUDIO_PWRON		IMX_GPIO_NR(5, 17)
+#define NOVENA_FPGA_RESET_N_GPIO	IMX_GPIO_NR(5, 7)
+#define NOVENA_HDMI_GHOST_HPD		IMX_GPIO_NR(5, 4)
+#define NOVENA_PCIE_RESET_GPIO		IMX_GPIO_NR(3, 29)
+#define NOVENA_PCIE_POWER_ON_GPIO	IMX_GPIO_NR(7, 12)
+#define NOVENA_PCIE_WAKE_UP_GPIO	IMX_GPIO_NR(3, 22)
+#define NOVENA_PCIE_DISABLE_GPIO	IMX_GPIO_NR(2, 16)
+
+/*
+ * Audio
+ */
+static iomux_v3_cfg_t audio_pads[] = {
+	/* AUD_PWRON */
+	MX6_PAD_DISP0_DAT23__GPIO5_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void novena_spl_setup_iomux_audio(void)
+{
+	imx_iomux_v3_setup_multiple_pads(audio_pads, ARRAY_SIZE(audio_pads));
+	gpio_direction_output(NOVENA_AUDIO_PWRON, 1);
+}
+
+/*
+ * ENET
+ */
+static iomux_v3_cfg_t enet_pads1[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+
+	/* pin 35, PHY_AD2 */
+	MX6_PAD_RGMII_RXC__GPIO6_IO30	| MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
+	/* pin 32, MODE0 */
+	MX6_PAD_RGMII_RD0__GPIO6_IO25	| MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
+	/* pin 31, MODE1 */
+	MX6_PAD_RGMII_RD1__GPIO6_IO27	| MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
+	/* pin 28, MODE2 */
+	MX6_PAD_RGMII_RD2__GPIO6_IO28	| MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
+	/* pin 27, MODE3 */
+	MX6_PAD_RGMII_RD3__GPIO6_IO29	| MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
+	/* pin 33, CLK125_EN */
+	MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(ENET_PHY_CFG_PAD_CTRL),
+
+	/* pin 42 PHY nRST */
+	MX6_PAD_EIM_D23__GPIO3_IO23		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t enet_pads2[] = {
+	MX6_PAD_RGMII_RXC__RGMII_RXC		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3		| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(RGMII_PAD_CTRL),
+};
+
+static void novena_spl_setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
+
+	/* Assert Ethernet PHY nRST */
+	gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
+
+	/*
+	 * Use imx6 internal pull-ups to drive PHY mode pins during PHY reset
+	 * de-assertion. The intention is to use weak signal drivers (pull-ups)
+	 * to prevent the conflict between PHY pins becoming outputs after
+	 * reset and imx6 still driving the pins. The issue is described in PHY
+	 * datasheet, p.14
+	 */
+	gpio_direction_input(IMX_GPIO_NR(6, 30)); /* PHY_AD2 = 1 */
+	gpio_direction_input(IMX_GPIO_NR(6, 25)); /* MODE0 = 1 */
+	gpio_direction_input(IMX_GPIO_NR(6, 27)); /* MODE1 = 1 */
+	gpio_direction_input(IMX_GPIO_NR(6, 28)); /* MODE2 = 1 */
+	gpio_direction_input(IMX_GPIO_NR(6, 29)); /* MODE3 = 1 */
+	gpio_direction_input(IMX_GPIO_NR(6, 24)); /* CLK125_EN = 1 */
+
+	/* Following reset timing (p.53, fig.8 from the PHY datasheet) */
+	mdelay(10);
+
+	/* De-assert Ethernet PHY nRST */
+	gpio_set_value(IMX_GPIO_NR(3, 23), 1);
+
+	/* PHY is now configured, connect FEC to the pads */
+	imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
+
+	/*
+	 * PHY datasheet recommends on p.53 to wait at least 100us after reset
+	 * before using MII, so we enforce the delay here
+	 */
+	udelay(100);
+}
+
+/*
+ * FPGA
+ */
+static iomux_v3_cfg_t fpga_pads[] = {
+	/* FPGA_RESET_N */
+	MX6_PAD_DISP0_DAT13__GPIO5_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void novena_spl_setup_iomux_fpga(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fpga_pads, ARRAY_SIZE(fpga_pads));
+	gpio_direction_output(NOVENA_FPGA_RESET_N_GPIO, 0);
+}
+
+/*
+ * GPIO Button
+ */
+static iomux_v3_cfg_t button_pads[] = {
+	/* Debug */
+	MX6_PAD_KEY_COL4__GPIO4_IO14 | MUX_PAD_CTRL(BUTTON_PAD_CTRL),
+};
+
+static void novena_spl_setup_iomux_buttons(void)
+{
+	imx_iomux_v3_setup_multiple_pads(button_pads, ARRAY_SIZE(button_pads));
+}
+
+/*
+ * I2C
+ */
+/*
+ * I2C1:
+ *  0x1d ... MMA7455L
+ *  0x30 ... SO-DIMM temp sensor
+ *  0x44 ... STMPE610
+ *  0x50 ... SO-DIMM ID
+ */
+struct i2c_pads_info i2c_pad_info0 = {
+	.scl = {
+		.i2c_mode	= MX6_PAD_EIM_D21__I2C1_SCL | PC,
+		.gpio_mode	= MX6_PAD_EIM_D21__GPIO3_IO21 | PC,
+		.gp		= IMX_GPIO_NR(3, 21)
+	},
+	.sda = {
+		.i2c_mode	= MX6_PAD_EIM_D28__I2C1_SDA | PC,
+		.gpio_mode	= MX6_PAD_EIM_D28__GPIO3_IO28 | PC,
+		.gp		= IMX_GPIO_NR(3, 28)
+	}
+};
+
+/*
+ * I2C2:
+ *  0x08 ... PMIC
+ *  0x3a ... HDMI DCC
+ *  0x50 ... HDMI DCC
+ */
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode	= MX6_PAD_EIM_EB2__I2C2_SCL | PC,
+		.gpio_mode	= MX6_PAD_EIM_EB2__GPIO2_IO30 | PC,
+		.gp		= IMX_GPIO_NR(2, 30)
+	},
+	.sda = {
+		.i2c_mode	= MX6_PAD_EIM_D16__I2C2_SDA | PC,
+		.gpio_mode	= MX6_PAD_EIM_D16__GPIO3_IO16 | PC,
+		.gp		= IMX_GPIO_NR(3, 16)
+	}
+};
+
+/*
+ * I2C3:
+ *  0x11 ... ES8283
+ *  0x50 ... LCD EDID
+ *  0x56 ... EEPROM
+ */
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode	= MX6_PAD_EIM_D17__I2C3_SCL | PC,
+		.gpio_mode	= MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
+		.gp		= IMX_GPIO_NR(3, 17)
+	},
+	.sda = {
+		.i2c_mode	= MX6_PAD_EIM_D18__I2C3_SDA | PC,
+		.gpio_mode	= MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
+		.gp		= IMX_GPIO_NR(3, 18)
+	}
+};
+
+static void novena_spl_setup_iomux_i2c(void)
+{
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+}
+
+/*
+ * PCI express
+ */
+#ifdef CONFIG_CMD_PCI
+static iomux_v3_cfg_t pcie_pads[] = {
+	/* "Reset" pin */
+	MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* "Power on" pin */
+	MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* "Wake up" pin (input) */
+	MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* "Disable endpoint" (rfkill) pin */
+	MX6_PAD_EIM_A22__GPIO2_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void novena_spl_setup_iomux_pcie(void)
+{
+	imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
+
+	/* Ensure PCIe is powered down */
+	gpio_direction_output(NOVENA_PCIE_POWER_ON_GPIO, 0);
+
+	/* Put the card into reset */
+	gpio_direction_output(NOVENA_PCIE_RESET_GPIO, 0);
+
+	/* Input signal to wake system from mPCIe card */
+	gpio_direction_input(NOVENA_PCIE_WAKE_UP_GPIO);
+
+	/* Drive RFKILL high, to ensure the radio is turned on */
+	gpio_direction_output(NOVENA_PCIE_DISABLE_GPIO, 1);
+}
+#else
+static inline void novena_spl_setup_iomux_pcie(void) {}
+#endif
+
+/*
+ * SDHC
+ */
+static iomux_v3_cfg_t usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__SD2_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CMD__SD2_CMD    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_GPIO_2__GPIO1_IO02  | MUX_PAD_CTRL(NO_PAD_CTRL), /* WP */
+	MX6_PAD_GPIO_4__GPIO1_IO04  | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+static iomux_v3_cfg_t usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__SD3_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__SD3_CMD    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static void novena_spl_setup_iomux_sdhc(void)
+{
+	imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+	imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+
+	/* Big SD write-protect and card-detect */
+	gpio_direction_input(IMX_GPIO_NR(1, 2));
+	gpio_direction_input(IMX_GPIO_NR(1, 4));
+}
+
+/*
+ * SPI
+ */
+#ifdef CONFIG_MXC_SPI
+static iomux_v3_cfg_t ecspi3_pads[] = {
+	/* SS1 */
+	MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT3__GPIO4_IO24 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT4__GPIO4_IO25 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT5__GPIO4_IO26 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT7__ECSPI3_RDY | MUX_PAD_CTRL(SPI_PAD_CTRL),
+};
+
+static void novena_spl_setup_iomux_spi(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi3_pads, ARRAY_SIZE(ecspi3_pads));
+	/* De-assert the nCS */
+	gpio_direction_output(MX6_PAD_DISP0_DAT3__GPIO4_IO24, 1);
+	gpio_direction_output(MX6_PAD_DISP0_DAT4__GPIO4_IO25, 1);
+	gpio_direction_output(MX6_PAD_DISP0_DAT5__GPIO4_IO26, 1);
+}
+#else
+static void novena_spl_setup_iomux_spi(void) {}
+#endif
+
+/*
+ * UART
+ */
+static iomux_v3_cfg_t const uart2_pads[] = {
+	MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart3_pads[] = {
+	MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT16__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT17__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+
+};
+
+static void novena_spl_setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+	imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
+	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+}
+
+/*
+ * Video
+ */
+#ifdef CONFIG_VIDEO
+static iomux_v3_cfg_t hdmi_pads[] = {
+	/* "Ghost HPD" pin */
+	MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void novena_spl_setup_iomux_video(void)
+{
+	imx_iomux_v3_setup_multiple_pads(hdmi_pads, ARRAY_SIZE(hdmi_pads));
+	gpio_direction_input(NOVENA_HDMI_GHOST_HPD);
+}
+#else
+static inline void novena_spl_setup_iomux_video(void) {}
+#endif
+
+/*
+ * SPL boots from uSDHC card
+ */
+#ifdef CONFIG_FSL_ESDHC
+static struct fsl_esdhc_cfg usdhc_cfg = {
+	USDHC3_BASE_ADDR, 0, 4
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	/* There is no CD for a microSD card, assume always present. */
+	return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+	return fsl_esdhc_initialize(bis, &usdhc_cfg);
+}
+#endif
+
+/* Configure MX6Q/DUAL mmdc DDR io registers */
+static struct mx6dq_iomux_ddr_regs novena_ddr_ioregs = {
+	/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
+	.dram_sdclk_0		= 0x00020038,
+	.dram_sdclk_1		= 0x00020038,
+	.dram_cas		= 0x00000038,
+	.dram_ras		= 0x00000038,
+	.dram_reset		= 0x00000038,
+	/* SDCKE[0:1]: 100k pull-up */
+	.dram_sdcke0		= 0x00003000,
+	.dram_sdcke1		= 0x00003000,
+	/* SDBA2: pull-up disabled */
+	.dram_sdba2		= 0x00000000,
+	/* SDODT[0:1]: 100k pull-up, 40 ohm */
+	.dram_sdodt0		= 0x00000038,
+	.dram_sdodt1		= 0x00000038,
+	/* SDQS[0:7]: Differential input, 40 ohm */
+	.dram_sdqs0		= 0x00000038,
+	.dram_sdqs1		= 0x00000038,
+	.dram_sdqs2		= 0x00000038,
+	.dram_sdqs3		= 0x00000038,
+	.dram_sdqs4		= 0x00000038,
+	.dram_sdqs5		= 0x00000038,
+	.dram_sdqs6		= 0x00000038,
+	.dram_sdqs7		= 0x00000038,
+
+	/* DQM[0:7]: Differential input, 40 ohm */
+	.dram_dqm0		= 0x00000038,
+	.dram_dqm1		= 0x00000038,
+	.dram_dqm2		= 0x00000038,
+	.dram_dqm3		= 0x00000038,
+	.dram_dqm4		= 0x00000038,
+	.dram_dqm5		= 0x00000038,
+	.dram_dqm6		= 0x00000038,
+	.dram_dqm7		= 0x00000038,
+};
+
+/* Configure MX6Q/DUAL mmdc GRP io registers */
+static struct mx6dq_iomux_grp_regs novena_grp_ioregs = {
+	/* DDR3 */
+	.grp_ddr_type		= 0x000c0000,
+	.grp_ddrmode_ctl	= 0x00020000,
+	/* Disable DDR pullups */
+	.grp_ddrpke		= 0x00000000,
+	/* ADDR[00:16], SDBA[0:1]: 40 ohm */
+	.grp_addds		= 0x00000038,
+	/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
+	.grp_ctlds		= 0x00000038,
+	/* DATA[00:63]: Differential input, 40 ohm */
+	.grp_ddrmode		= 0x00020000,
+	.grp_b0ds		= 0x00000038,
+	.grp_b1ds		= 0x00000038,
+	.grp_b2ds		= 0x00000038,
+	.grp_b3ds		= 0x00000038,
+	.grp_b4ds		= 0x00000038,
+	.grp_b5ds		= 0x00000038,
+	.grp_b6ds		= 0x00000038,
+	.grp_b7ds		= 0x00000038,
+};
+
+static struct mx6_mmdc_calibration novena_mmdc_calib = {
+	/* write leveling calibration determine */
+	.p0_mpwldectrl0		= 0x00420048,
+	.p0_mpwldectrl1		= 0x006f0059,
+	.p1_mpwldectrl0		= 0x005a0104,
+	.p1_mpwldectrl1		= 0x01070113,
+	/* Read DQS Gating calibration */
+	.p0_mpdgctrl0		= 0x437c040b,
+	.p0_mpdgctrl1		= 0x0413040e,
+	.p1_mpdgctrl0		= 0x444f0446,
+	.p1_mpdgctrl1		= 0x044d0422,
+	/* Read Calibration: DQS delay relative to DQ read access */
+	.p0_mprddlctl		= 0x4c424249,
+	.p1_mprddlctl		= 0x4e48414f,
+	/* Write Calibration: DQ/DM delay relative to DQS write access */
+	.p0_mpwrdlctl		= 0x42414641,
+	.p1_mpwrdlctl		= 0x46374b43,
+};
+
+static struct mx6_ddr_sysinfo novena_ddr_info = {
+	/* Width of data bus: 0=16, 1=32, 2=64 */
+	.dsize		= 2,
+	/* Config for full 4GB range so that get_mem_size() works */
+	.cs_density	= 32,	/* 32Gb per CS */
+	/* Single chip select */
+	.ncs		= 1,
+	.cs1_mirror	= 0,
+	.rtt_wr		= 1,	/* RTT_Wr = RZQ/4 */
+	.rtt_nom	= 2,	/* RTT_Nom = RZQ/2 */
+	.walat		= 3,	/* Write additional latency */
+	.ralat		= 7,	/* Read additional latency */
+	.mif3_mode	= 3,	/* Command prediction working mode */
+	.bi_on		= 1,	/* Bank interleaving enabled */
+	.sde_to_rst	= 0x10,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke	= 0x23,	/* 33 cycles, 500us (JEDEC default) */
+};
+
+static struct mx6_ddr3_cfg elpida_4gib_1600 = {
+	.mem_speed	= 1600,
+	.density	= 4,
+	.width		= 64,
+	.banks		= 8,
+	.rowaddr	= 16,
+	.coladdr	= 10,
+	.pagesz		= 2,
+	.trcd		= 1300,
+	.trcmin		= 4900,
+	.trasmin	= 3590,
+};
+
+/*
+ * called from C runtime startup code (arch/arm/lib/crt0.S:_main)
+ * - we have a stack and a place to store GD, both in SRAM
+ * - no variable global data is available
+ */
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	/* setup GP timer */
+	timer_init();
+
+#ifdef CONFIG_BOARD_POSTCLK_INIT
+	board_postclk_init();
+#endif
+#ifdef CONFIG_FSL_ESDHC
+	get_clocks();
+#endif
+
+	/* Setup IOMUX and configure basics. */
+	novena_spl_setup_iomux_audio();
+	novena_spl_setup_iomux_buttons();
+	novena_spl_setup_iomux_enet();
+	novena_spl_setup_iomux_fpga();
+	novena_spl_setup_iomux_i2c();
+	novena_spl_setup_iomux_pcie();
+	novena_spl_setup_iomux_sdhc();
+	novena_spl_setup_iomux_spi();
+	novena_spl_setup_iomux_uart();
+	novena_spl_setup_iomux_video();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* Start the DDR DRAM */
+	mx6dq_dram_iocfg(64, &novena_ddr_ioregs, &novena_grp_ioregs);
+	mx6_dram_cfg(&novena_ddr_info, &novena_mmdc_calib, &elpida_4gib_1600);
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
+
+void reset_cpu(ulong addr)
+{
+}
diff --git a/board/kosagi/novena/setup.cfg b/board/kosagi/novena/setup.cfg
new file mode 100644
index 0000000..18d139c
--- /dev/null
+++ b/board/kosagi/novena/setup.cfg
@@ -0,0 +1,47 @@
+/*
+ * Copyright (C) 2014 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+IMAGE_VERSION 2
+
+/* Boot Device : sd */
+BOOT_FROM sd
+
+#define __ASSEMBLY__
+#include <config.h>
+#include "asm/arch/iomux.h"
+#include "asm/arch/crm_regs.h"
+
+/* set the default clock gate to save power */
+DATA 4, CCM_CCGR0, 0x00C03F3F
+DATA 4, CCM_CCGR1, 0x0030FC03
+DATA 4, CCM_CCGR2, 0x0FFFC000
+DATA 4, CCM_CCGR3, 0x3FF00000
+DATA 4, CCM_CCGR4, 0xFFFFF300 /* enable NAND/GPMI/BCH clocks */
+DATA 4, CCM_CCGR5, 0x0F0000C3
+DATA 4, CCM_CCGR6, 0x000003FF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
+DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
+
+/*
+ * Setup CCM_CCOSR register as follows:
+ *
+ * cko1_en  = 1    --> CKO1 enabled
+ * cko1_div = 111  --> divide by 8
+ * cko1_sel = 1011 --> ahb_clk_root
+ *
+ * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz
+ */
+DATA 4, CCM_CCOSR, 0x000000fb
diff --git a/board/tqc/tqma6/tqma6.c b/board/tqc/tqma6/tqma6.c
index b552bb8..fd1bd59 100644
--- a/board/tqc/tqma6/tqma6.c
+++ b/board/tqc/tqma6/tqma6.c
@@ -138,8 +138,10 @@ static iomux_v3_cfg_t const tqma6_ecspi1_pads[] = {
 	NEW_PAD_CTRL(MX6_PAD_EIM_D18__ECSPI1_MOSI, SPI_PAD_CTRL),
 };
 
+#define TQMA6_SF_CS_GPIO IMX_GPIO_NR(3, 19)
+
 static unsigned const tqma6_ecspi1_cs[] = {
-	IMX_GPIO_NR(3, 19),
+	TQMA6_SF_CS_GPIO,
 };
 
 static void tqma6_iomuxc_spi(void)
@@ -152,6 +154,12 @@ static void tqma6_iomuxc_spi(void)
 					 ARRAY_SIZE(tqma6_ecspi1_pads));
 }
 
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return ((bus == CONFIG_SF_DEFAULT_BUS) &&
+		(cs == CONFIG_SF_DEFAULT_CS)) ? TQMA6_SF_CS_GPIO : -1;
+}
+
 static struct i2c_pads_info tqma6_i2c3_pads = {
 	/* I2C3: on board LM75, M24C64,  */
 	.scl = {
diff --git a/board/tqc/tqma6/tqma6_bb.h b/board/tqc/tqma6/tqma6_bb.h
index 9d072d2..fb7b462 100644
--- a/board/tqc/tqma6/tqma6_bb.h
+++ b/board/tqc/tqma6/tqma6_bb.h
@@ -6,7 +6,7 @@
  */
 
 #ifndef __TQMA6_BB__
-#define __TQMA6_BB
+#define __TQMA6_BB__
 
 #include <common.h>