Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  davinci: Remove unwanted memsize.c from hawkboard's nand spl build
  devkit8000: Move CONFIG_SYS_TEXT_BASE out of bss
  da850evm: pass board revision info to kernel
  arch/arm/include/asm/arch-omap5/clocks.h: Fix GCC 4.2 warnings
  arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix GCC 4.6 warnings
  arch/arm/cpu/armv7/omap-common/spl.c: Fix GCC 4.2 warnings
  MX35: flea3: changes due to hardware revision B
  MX: serial_mxc: cleanup removing nasty #ifdef
  M28: Fix OB1 bug in GPIO driver
  MXS: Add static annotations to dma driver
  apbh_dma: return error value on timeout
  Efika: Configure additional regulators for HDMI output
  mx5: Correct a warning in clock.c
  MC13892: Add REGMODE0 bits definitions
  mx51evk: Configure the pins as GPIOs prior to using gpio_get_value
  mx53smd: Configure the pins as GPIOs prior to using gpio_get_value
  mx53evk: Configure the pins as GPIOs prior to using gpio_get_value
  mx53ard: Configure the pins as GPIOs prior to using gpio_get_value
  mx53loco: Configure the pins as GPIOs prior to using gpio_get_value
  OMAP3: Add SPL_BOARD_INIT hook
  AM3517 CraneBoard: Add SPL support
  AM3517: Add SPL support
  OMAP3: Add SPL support to omap3_evm
  OMAP3: Add SPL support to Beagleboard
  OMAP3 SPL: Add identify_nand_chip function
  OMAP3 SPL: Rework memory initalization and devkit8000 support
  OMAP3: Suffix all Micron memory timing parts with their speed
  OMAP3: Add optimal SDRC autorefresh control values
  omap3: mem: Add MCFG helper macro
  OMAP3: Remove get_mem_type prototype
  OMAP3: Change mem_ok to clear again after reading back
  OMAP3: Add a helper function to set timings in SDRC
  OMAP3: Update SDRC dram_init to always call make_cs1_contiguous()
  omap3: mem: Comment enable_gpmc_cs_config more
  ARM: davici_emac: Fix condition for number of phy detects
  arm: printf() is not available in some SPL configurations
  arm, davinci: add support for am1808 based enbw_cmc board
  arm, davinci: move misc function in arch tree
  arm, board/davinci/common/misc.c: Codingstyle cleanup
  arm, davinci, da850: add uart1 tx rx pinmux config
  arm, davinci: move davinci_rtc struct to hardware.h
  arm, davinci: Remove duplication of pinmux configuration code
  arm, hawkboard: Use the pinmux configurations defined in the arch tree
  arm, da850evm: Use the pinmux configurations defined in the arch tree
  arm, da850: Add pinmux configurations to the arch tree
  arm, da850evm: Do pinmux configuration for EMAC together with other pinmuxes
  arm, hawkboard: Remove obsolete struct pinmux_config i2c_pins
  arm, davinci: Move pinmux functions from board to arch tree
  arm, arm926ejs: always do cpu critical inits
  omap_gpmc: use SOFTECC in SPL if it's enabled
  nand_spl_simple: add support for software ECC
  AM3517: move AM3517 specific mux defines to generic header
  AM35xx: add EMAC support
  davinci_emac: hardcode 100Mbps for AM35xx and RMII
  davinci_emac: fix for running with dcache enabled
  arm926ejs: add noop implementation for dcache ops
  davinci_emac: conditionally compile specific PHY support
  davinci_emac: use internal addresses in buffer descriptors
  davinci_emac: move arch-independent defines to separate header
  BeagleBoard: config: Really switch to ttyO2
  ARM: davinci_dm6467Tevm: Fix build breakage
  ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused
  ARM: OMAP3: Remove unused define SDRC_R_C_B
  ARM: OMAP3: Remove unused define CONFIG_OMAP3430
  omap4: fix IO setting
  omap4+: streamline CONFIG_SYS_TEXT_BASE and other SDRAM addresses
  omap4460: add ES1.1 identification
  omap4: emif: fix error in driver
  omap: remove I2C from SPL
  omap4460: fix TPS initialization
  omap: fix cache line size for omap3/omap4 boards
  omap4: ttyO2 instead of ttyS2 in default bootargs
  omap: Improve PLL parameter calculation tool
  start.S: remove omap3 specific code from start.S
  armv7: setup vector
  armv7: include armv7/cpu.c in SPL build
  armv7: disable L2 cache in cleanup_before_linux()
  arm, arm926ejs: Fix clear bss loop for zero length bss
  PXA: Move colibri_pxa270 to board/toradex/
  PXA: Flip colibri_pxa27x to pxa-common.h
  PXA: Introduce common configuration header for PXA
  PXA: Rename pxa_dram_init to pxa2xx_dram_init
  PXA: Squash extern pxa_dram_init()
  PXA: Export cpu_is_ and pxa_dram_init functions
  PXA: Cleanup Colibri PXA270
  PXA: Replace timer driver
  PXA: Add cpuinfo display for PXA2xx
  PXA: Separate PXA2xx CPU init
  PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]X
  PXA: Unify vpac270 environment size
  PXA: Enable command line editing for vpac270
  PXA: Adapt Voipac PXA270 to OneNAND SPL
  PXA: Drop Voipac PXA270 OneNAND IPL
  PXA: Fixup PXA25x boards after start.S update
  PXA: Re-add the Dcache locking as RAM for pxa250
  PXA: Rework start.S to be closer to other ARMs
  PXA: Drop XM250 board
  PXA: Drop PLEB2 board
  PXA: Drop CRADLE board
  PXA: Drop CERF250 board
  Fix regression in SMDK6400
  nand: Add common functions to linux/mtd/nand.h
  Ethernut 5 board support
  net: Armada100: Fix compilation warnings
  ARM: remove duplicated code for LaCie boards
  ARM: add support for LaCie 2Big Network v2
  mvsata: fix ide_preinit for missing disks
  netspace_v2: Read Ethernet MAC address from EEPROM
  omap3evm: Add support for EFI partitions
  part_efi: Fix compile errors

1 files changed, 0 insertions, 535 deletions

diff --git a/board/xm250/flash.c b/board/xm250/flash.c
deleted file mode 100644
index e825aba..0000000
--- a/board/xm250/flash.c
+++ /dev/null
@@ -1,535 +0,0 @@
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2001-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];	/* info for FLASH chips    */
-
-/* Board support for 1 or 2 flash devices */
-#define FLASH_PORT_WIDTH32
-#undef FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH		ushort
-#define FLASH_PORT_WIDTHV		vu_short
-#define SWAP(x)               __swab16(x)
-#else
-#define FLASH_PORT_WIDTH		ulong
-#define FLASH_PORT_WIDTHV		vu_long
-#define SWAP(x)               __swab32(x)
-#endif
-
-/* Intel-compatible flash ID */
-#define INTEL_COMPAT  0x00890089
-#define INTEL_ALT     0x00B000B0
-
-/* Intel-compatible flash commands */
-#define INTEL_PROGRAM 0x00100010
-#define INTEL_ERASE   0x00200020
-#define INTEL_CLEAR   0x00500050
-#define INTEL_LOCKBIT 0x00600060
-#define INTEL_PROTECT 0x00010001
-#define INTEL_STATUS  0x00700070
-#define INTEL_READID  0x00900090
-#define INTEL_CONFIRM 0x00D000D0
-#define INTEL_RESET   0xFFFFFFFF
-
-/* Intel-compatible flash status bits */
-#define INTEL_FINISHED 0x00800080
-#define INTEL_OK       0x00800080
-
-#define FPW	   FLASH_PORT_WIDTH
-#define FPWV   FLASH_PORT_WIDTHV
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (FPW *addr, flash_info_t *info);
-static int write_data (flash_info_t *info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t *info);
-void inline spin_wheel (void);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	int i;
-	ulong size = 0;
-
-	for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
-		switch (i) {
-		case 0:
-			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
-			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
-			break;
-		case 1:
-			flash_get_size ((FPW *) PHYS_FLASH_2, &flash_info[i]);
-			flash_get_offsets (PHYS_FLASH_2, &flash_info[i]);
-			break;
-		default:
-			panic ("configured to many flash banks!\n");
-			break;
-		}
-		size += flash_info[i].size;
-	}
-
-	/* Protect monitor and environment sectors
-	 */
-	flash_protect ( FLAG_PROTECT_SET,
-			CONFIG_SYS_FLASH_BASE,
-			CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1,
-			&flash_info[0] );
-
-	flash_protect ( FLAG_PROTECT_SET,
-			CONFIG_ENV_ADDR,
-			CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0] );
-
-	return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return;
-	}
-
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
-		for (i = 0; i < info->sector_count; i++) {
-			info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
-			info->protect[i] = 0;
-		}
-	}
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_INTEL:
-		printf ("INTEL ");
-		break;
-	default:
-		printf ("Unknown Vendor ");
-		break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_28F128J3A:
-		printf ("28F128J3A\n");
-		break;
-
-	case FLASH_28F640J3A:
-		printf ("28F640J3A\n");
-		break;
-	default:
-		printf ("Unknown Chip Type\n");
-		break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-			info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i = 0; i < info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     ");
-	}
-	printf ("\n");
-	return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (FPW *addr, flash_info_t *info)
-{
-	volatile FPW value;
-
-	/* Write auto select command: read Manufacturer ID */
-	addr[0x5555] = (FPW) 0x00AA00AA;
-	addr[0x2AAA] = (FPW) 0x00550055;
-	addr[0x5555] = (FPW) 0x00900090;
-
-	mb ();
-	value = addr[0];
-
-	switch (value) {
-
-	case (FPW) INTEL_MANUFACT:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
-		return (0);			/* no or unknown flash  */
-	}
-
-	mb ();
-	value = addr[1];			/* device ID        */
-
-	switch (value) {
-
-	case (FPW) INTEL_ID_28F128J3A:
-		info->flash_id += FLASH_28F128J3A;
-		info->sector_count = 128;
-		info->size = 0x02000000;
-		break;				/* => 32 MB     */
-
-	case (FPW) INTEL_ID_28F640J3A:
-		info->flash_id += FLASH_28F640J3A;
-		info->sector_count = 64;
-		info->size = 0x01000000;
-		break;				/* => 16 MB     */
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		break;
-	}
-
-	if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
-		printf ("** ERROR: sector count %d > max (%d) **\n",
-			info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
-		info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
-	}
-
-	addr[0] = (FPW) 0x00FF00FF;		/* restore read mode */
-
-	return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	int flag, prot, sect;
-	ulong type, start;
-	int rcode = 0;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	type = (info->flash_id & FLASH_VENDMASK);
-	if ((type != FLASH_MAN_INTEL)) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect = s_first; sect <= s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect <= s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			FPWV *addr = (FPWV *) (info->start[sect]);
-			FPW status;
-
-			printf ("Erasing sector %2d ... ", sect);
-
-			/* arm simple, non interrupt dependent timer */
-			start = get_timer(0);
-
-			*addr = (FPW) 0x00500050;	/* clear status register */
-			*addr = (FPW) 0x00200020;	/* erase setup */
-			*addr = (FPW) 0x00D000D0;	/* erase confirm */
-
-			while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
-				if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT) {
-					printf ("Timeout\n");
-					*addr = (FPW) 0x00B000B0;	/* suspend erase     */
-					*addr = (FPW) 0x00FF00FF;	/* reset to read mode */
-					rcode = 1;
-					break;
-				}
-			}
-
-			*addr = 0x00500050;	/* clear status register cmd.   */
-			*addr = 0x00FF00FF;	/* resest to read mode          */
-
-			printf (" done\n");
-		}
-	}
-	return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong cp, wp;
-	FPW data;
-	int count, i, l, rc, port_width;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return 4;
-	}
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
-	wp = (addr & ~1);
-	port_width = 2;
-#else
-	wp = (addr & ~3);
-	port_width = 4;
-#endif
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i = 0, cp = wp; i < l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-		for (; i < port_width && cnt > 0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt == 0 && i < port_width; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-
-		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	count = 0;
-	while (cnt >= port_width) {
-		data = 0;
-		for (i = 0; i < port_width; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-		cnt -= port_width;
-		if (count++ > 0x800) {
-			spin_wheel ();
-			count = 0;
-		}
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i < port_width; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *) cp);
-	}
-
-	return (write_data (info, wp, SWAP (data)));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t *info, ulong dest, FPW data)
-{
-	FPWV *addr = (FPWV *) dest;
-	ulong status;
-	int flag;
-	ulong start;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*addr & data) != data) {
-		printf ("not erased at %08lx (%lx)\n", (ulong) addr, *addr);
-		return (2);
-	}
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-
-	*addr = (FPW) 0x00400040;	/* write setup */
-	*addr = data;
-
-	/* arm simple, non interrupt dependent timer */
-	start = get_timer(0);
-
-	/* wait while polling the status register */
-	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
-		if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
-			return (1);
-		}
-	}
-
-	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
-
-	return (0);
-}
-
-void inline spin_wheel (void)
-{
-	static int p = 0;
-	static char w[] = "\\/-";
-
-	printf ("\010%c", w[p]);
-	(++p == 3) ? (p = 0) : 0;
-}
-
-/*-----------------------------------------------------------------------
- * Set/Clear sector's lock bit, returns:
- * 0 - OK
- * 1 - Error (timeout, voltage problems, etc.)
- */
-int flash_real_protect(flash_info_t *info, long sector, int prot)
-{
-	int i;
-	int rc = 0;
-	vu_long *addr = (vu_long *)(info->start[sector]);
-	int flag = disable_interrupts();
-	ulong start;
-
-	*addr = INTEL_CLEAR;	/* Clear status register */
-	if (prot) {			/* Set sector lock bit */
-		*addr = INTEL_LOCKBIT;	/* Sector lock bit */
-		*addr = INTEL_PROTECT;	/* set */
-	}
-	else {				/* Clear sector lock bit */
-		*addr = INTEL_LOCKBIT;	/* All sectors lock bits */
-		*addr = INTEL_CONFIRM;	/* clear */
-	}
-
-	start = get_timer(0);
-
-	while ((*addr & INTEL_FINISHED) != INTEL_FINISHED) {
-		if (get_timer(start) > CONFIG_SYS_FLASH_UNLOCK_TOUT) {
-			printf("Flash lock bit operation timed out\n");
-			rc = 1;
-			break;
-		}
-	}
-
-	if (*addr != INTEL_OK) {
-		printf("Flash lock bit operation failed at %08X, CSR=%08X\n",
-		       (uint)addr, (uint)*addr);
-		rc = 1;
-	}
-
-	if (!rc)
-		info->protect[sector] = prot;
-
-	/*
-	 * Clear lock bit command clears all sectors lock bits, so
-	 * we have to restore lock bits of protected sectors.
-	 */
-	if (!prot)
-	{
-		for (i = 0; i < info->sector_count; i++)
-		{
-			if (info->protect[i])
-			{
-				start = get_timer(0);
-				addr = (vu_long *)(info->start[i]);
-				*addr = INTEL_LOCKBIT;	/* Sector lock bit */
-				*addr = INTEL_PROTECT;	/* set */
-				while ((*addr & INTEL_FINISHED) != INTEL_FINISHED)
-				{
-					if (get_timer(start) > CONFIG_SYS_FLASH_UNLOCK_TOUT)
-					{
-						printf("Flash lock bit operation timed out\n");
-						rc = 1;
-						break;
-					}
-				}
-			}
-		}
-	}
-
-	if (flag)
-		enable_interrupts();
-
-	*addr = INTEL_RESET;		/* Reset to read array mode */
-
-	return rc;
-}