hmi1001, mucmc52, uc100, uc101: move boards to vendor directory

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Roderik Wildenburg <roderik.wildenburg@manroland.com>

1 files changed, 0 insertions, 198 deletions

diff --git a/board/uc100/pcmcia.c b/board/uc100/pcmcia.c
deleted file mode 100644
index ad25678..0000000
--- a/board/uc100/pcmcia.c
+++ /dev/null
@@ -1,198 +0,0 @@
-#include <common.h>
-#include <mpc8xx.h>
-#include <pcmcia.h>
-
-#undef	CONFIG_PCMCIA
-
-#if defined(CONFIG_CMD_PCMCIA)
-#define	CONFIG_PCMCIA
-#endif
-
-#if (defined(CONFIG_CMD_IDE)) && defined(CONFIG_IDE_8xx_PCCARD)
-#define	CONFIG_PCMCIA
-#endif
-
-#ifdef	CONFIG_PCMCIA
-
-#define PCMCIA_BOARD_MSG "UC100"
-
-/*
- * Remark: don't turn off OE "__MY_PCMCIA_GCRX_CXOE" on UC100 board.
- *         This leads to board-hangup! (sr, 8 Dez. 2004)
- */
-static void cfg_ports (void)
-{
-	volatile immap_t	*immap;
-
-	immap = (immap_t *)CONFIG_SYS_IMMR;
-
-	/*
-	* Configure Port A for MAX1602 PC-Card Power-Interface Switch
-	*/
-	immap->im_ioport.iop_padat &= ~0x8000;	/* set port x output to low */
-	immap->im_ioport.iop_padir |= 0x8000;	/* enable port x as output */
-
-	debug ("Set Port A: PAR: %08x DIR: %08x DAT: %08x\n",
-	       immap->im_ioport.iop_papar, immap->im_ioport.iop_padir,
-	       immap->im_ioport.iop_padat);
-}
-
-int pcmcia_hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, mask;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	immap = (immap_t *)CONFIG_SYS_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-	cp    = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
-
-	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
-	cfg_ports ();
-
-	/*
-	* Configure SIUMCR to enable PCMCIA port B
-	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-	*/
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
-	/*
-	* Disable interrupts, DMA, and PCMCIA buffers
-	* (isolate the interface) and assert RESET signal
-	*/
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	* Make sure there is a card in the slot, then configure the interface.
-	*/
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-	       __LINE__,__FUNCTION__,
-	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	* Power On.
-	*/
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	reg  = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-	       reg,
-	       (reg&PCMCIA_VS1(slot))?"n":"ff",
-	       (reg&PCMCIA_VS2(slot))?"n":"ff");
-	if ((reg & mask) == mask) {
-		puts (" 5.0V card found: ");
-	} else {
-		puts (" 3.3V card found: ");
-	}
-
-	/*  switch VCC on */
-	immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */
-
-	udelay(10000);
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile cpm8xx_t	*cp;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CONFIG_SYS_IMMR;
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-
-	/* switch VCC off */
-	immap->im_ioport.iop_padat &= ~0x8000; /* power disable 3.3V */
-
-	/* Configure PCMCIA General Control Register */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(10000);
-
-	return (0);
-}
-#endif
-
-
-int pcmcia_voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("voltage_set: "
-			PCMCIA_BOARD_MSG
-			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	immap = (immap_t *)CONFIG_SYS_IMMR;
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-	/*
-	* Disable PCMCIA buffers (isolate the interface)
-	* and assert RESET signal
-	*/
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(_slot_);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	* Configure Port C pins for
-	* 5 Volts Enable and 3 Volts enable,
-	* Turn all power pins to Hi-Z
-	*/
-	debug ("PCMCIA power OFF\n");
-	cfg_ports ();	/* Enables switch, but all in Hi-Z */
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-	       slot+'A');
-	return (0);
-}
-
-#endif	/* CONFIG_PCMCIA */