* Patches by David Müller, 12 Jun 2003:

  - rewrite of the S3C24X0 register definitions stuff
  - "driver" for the built-in S3C24X0 RTC

* Patches by Yuli Barcohen, 12 Jun 2003:
  - Add MII support and Ethernet PHY initialization for MPC8260ADS board
  - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset
    configuration word supplied by FPGA on some MPC8260ADS boards

* Patch by Pantelis Antoniou, 10 Jun 2003:
  Unify status LED interface

2 files changed, 101 insertions, 76 deletions

diff --git a/board/trab/trab.c b/board/trab/trab.c
index 6c9971f..dd4105d 100644
--- a/board/trab/trab.c
+++ b/board/trab/trab.c
@@ -71,37 +71,39 @@ int board_init ()
 	extern int vfd_init_clocks(void);
 #endif
 	DECLARE_GLOBAL_DATA_PTR;
+	S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER();
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
 
 	/* memory and cpu-speed are setup before relocation */
 #ifdef CONFIG_TRAB_50MHZ
 	/* change the clock to be 50 MHz 1:1:1 */
 	/* MDIV:0x5c PDIV:4 SDIV:2 */
-	rMPLLCON = 0x5c042;
-	rCLKDIVN = 0;
+	clk_power->MPLLCON = 0x5c042;
+	clk_power->CLKDIVN = 0;
 #else
 	/* change the clock to be 133 MHz 1:2:4 */
 	/* MDIV:0x7d PDIV:4 SDIV:1 */
-	rMPLLCON = 0x7d041;
-	rCLKDIVN = 3;
+	clk_power->MPLLCON = 0x7d041;
+	clk_power->CLKDIVN = 3;
 #endif
 
 	/* set up the I/O ports */
-	rPACON = 0x3ffff;
-	rPBCON = 0xaaaaaaaa;
-	rPBUP  = 0xffff;
+	gpio->PACON = 0x3ffff;
+	gpio->PBCON = 0xaaaaaaaa;
+	gpio->PBUP  = 0xffff;
 	/* INPUT nCTS0 nRTS0 TXD[1] TXD[0] RXD[1] RXD[0]	*/
 	/*  00,    10,      10,      10,      10,      10,      10 	*/
-	rPFCON = (2<<0) | (2<<2) | (2<<4) | (2<<6) | (2<<8) | (2<<10);
+	gpio->PFCON = (2<<0) | (2<<2) | (2<<4) | (2<<6) | (2<<8) | (2<<10);
 #ifdef CONFIG_HWFLOW
 	/* do not pull up RXD0, RXD1, TXD0, TXD1, CTS0, RTS0 */
-	rPFUP  = (1<<0) | (1<<1) | (1<<2) | (1<<3) | (1<<4) | (1<<5);
+	gpio->PFUP  = (1<<0) | (1<<1) | (1<<2) | (1<<3) | (1<<4) | (1<<5);
 #else
 	/* do not pull up RXD0, RXD1, TXD0, TXD1 */
-	rPFUP  = (1<<0) | (1<<1) | (1<<2) | (1<<3);
+	gpio->PFUP  = (1<<0) | (1<<1) | (1<<2) | (1<<3);
 #endif
-	rPGCON = 0x0;
-	rPGUP  = 0x0;
-	rOPENCR= 0x0;
+	gpio->PGCON = 0x0;
+	gpio->PGUP  = 0x0;
+	gpio->OPENCR= 0x0;
 
 	/* arch number of SAMSUNG-Board */
 	/* MACH_TYPE_SMDK2400 */
@@ -112,8 +114,8 @@ int board_init ()
 	gd->bd->bi_boot_params = 0x0c000100;
 
 	/* Make sure both buzzers are turned off */
-	rPDCON |= 0x5400;
-	rPDDAT &= ~0xE0;
+	gpio->PDCON |= 0x5400;
+	gpio->PDDAT &= ~0xE0;
 
 #ifdef CONFIG_VFD
 	vfd_init_clocks();
@@ -305,57 +307,73 @@ static int key_pressed(void)
 
 #ifdef CFG_BRIGHTNESS
 
-#define SET_CS_TOUCH        (rPDDAT &= 0x5FF)
-#define CLR_CS_TOUCH        (rPDDAT |= 0x200)
+static inline void SET_CS_TOUCH(void)
+{
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+	gpio->PDDAT &= 0x5FF;
+}
+
+static inline void CLR_CS_TOUCH(void)
+{
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+	gpio->PDDAT |= 0x200;
+}
 
 static void spi_init(void)
 {
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+	S3C24X0_SPI * const spi = S3C24X0_GetBase_SPI();
 	int i;
 
 	/* Configure I/O ports. */
- 	rPDCON = (rPDCON & 0xF3FFFF) | 0x040000;
-	rPGCON = (rPGCON & 0x0F3FFF) | 0x008000;
-	rPGCON = (rPGCON & 0x0CFFFF) | 0x020000;
-	rPGCON = (rPGCON & 0x03FFFF) | 0x080000;
+ 	gpio->PDCON = (gpio->PDCON & 0xF3FFFF) | 0x040000;
+	gpio->PGCON = (gpio->PGCON & 0x0F3FFF) | 0x008000;
+	gpio->PGCON = (gpio->PGCON & 0x0CFFFF) | 0x020000;
+	gpio->PGCON = (gpio->PGCON & 0x03FFFF) | 0x080000;
 
-	CLR_CS_TOUCH;
+	CLR_CS_TOUCH();
 
-	rSPPRE = 0x1F; /* Baudrate ca. 514kHz */
-	rSPPIN = 0x01;  /* SPI-MOSI holds Level after last bit */
-	rSPCON = 0x1A;  /* Polling, Prescaler, Master, CPOL=0, CPHA=1 */
+	spi->ch[0].SPPRE = 0x1F; /* Baudrate ca. 514kHz */
+	spi->ch[0].SPPIN = 0x01;  /* SPI-MOSI holds Level after last bit */
+	spi->ch[0].SPCON = 0x1A;  /* Polling, Prescaler, Master, CPOL=0, CPHA=1 */
 
 	/* Dummy byte ensures clock to be low. */
 	for (i = 0; i < 10; i++) {
-		rSPTDAT = 0xFF;
+		spi->ch[0].SPTDAT = 0xFF;
 	}
 	wait_transmit_done();
 }
 
 static void wait_transmit_done(void)
 {
-	while (!(rSPSTA & 0x01)); /* wait until transfer is done */
+	S3C24X0_SPI * const spi = S3C24X0_GetBase_SPI();
+
+	while (!(spi->ch[0].SPSTA & 0x01)); /* wait until transfer is done */
 }
 
 static void tsc2000_write(unsigned int page, unsigned int reg,
 						  unsigned int data)
 {
+	S3C24X0_SPI * const spi = S3C24X0_GetBase_SPI();
 	unsigned int command;
 
-	SET_CS_TOUCH;
+	SET_CS_TOUCH();
 	command = 0x0000;
 	command |= (page << 11);
 	command |= (reg << 5);
 
-	rSPTDAT = (command & 0xFF00) >> 8;
+	spi->ch[0].SPTDAT = (command & 0xFF00) >> 8;
 	wait_transmit_done();
-	rSPTDAT = (command & 0x00FF);
+	spi->ch[0].SPTDAT = (command & 0x00FF);
 	wait_transmit_done();
-	rSPTDAT = (data & 0xFF00) >> 8;
+	spi->ch[0].SPTDAT = (data & 0xFF00) >> 8;
 	wait_transmit_done();
-	rSPTDAT = (data & 0x00FF);
+	spi->ch[0].SPTDAT = (data & 0x00FF);
 	wait_transmit_done();
 
-	CLR_CS_TOUCH;
+	CLR_CS_TOUCH();
 }
 
 static void tsc2000_set_brightness(void)
diff --git a/board/trab/vfd.c b/board/trab/vfd.c
index e00294f..1abc2ad 100644
--- a/board/trab/vfd.c
+++ b/board/trab/vfd.c
@@ -359,14 +359,17 @@ void transfer_pic(int display, unsigned char *adr, int height, int width)
  */
 int vfd_init_clocks (void)
 {
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+	S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS();
+	S3C24X0_LCD * const lcd = S3C24X0_GetBase_LCD();
 
 	/* try to determine display type from the value
 	 * defined by pull-ups
 	 */
-	rPCUP = (rPCUP & 0xFFF0);	/* activate  GPC0...GPC3 pullups */
-	rPCCON = (rPCCON & 0xFFFFFF00);	/* configure GPC0...GPC3 as inputs */
+	gpio->PCUP = (gpio->PCUP & 0xFFF0);	/* activate  GPC0...GPC3 pullups */
+	gpio->PCCON = (gpio->PCCON & 0xFFFFFF00);	/* configure GPC0...GPC3 as inputs */
 	udelay (10);				/* allow signals to settle */
-	vfd_board_id = (~rPCDAT) & 0x000F;	/* read GPC0...GPC3 port pins */
+	vfd_board_id = (~gpio->PCDAT) & 0x000F;	/* read GPC0...GPC3 port pins */
 
 	VFD_DISABLE;				/* activate blank for the vfd */
 
@@ -377,39 +380,39 @@ int vfd_init_clocks (void)
 		/* If new board revision, then use PWM 3 as cpld-clock */
 		/* Enable 500 Hz timer for fill level sensor to operate properly */
 		/* Configure TOUT3 as functional pin, disable pull-up */
-		rPDCON &= ~0x30000;
-		rPDCON |= 0x20000;
-		rPDUP |= (1 << 8);
+		gpio->PDCON &= ~0x30000;
+		gpio->PDCON |= 0x20000;
+		gpio->PDUP |= (1 << 8);
 
 		/* Configure the prescaler */
-		rTCFG0 &= ~0xff00;
-		rTCFG0 |= 0x0f00;
+		timers->TCFG0 &= ~0xff00;
+		timers->TCFG0 |= 0x0f00;
 
 		/* Select MUX input (divider) for timer3 (1/16) */
-		rTCFG1 &= ~0xf000;
-		rTCFG1 |= 0x3000;
+		timers->TCFG1 &= ~0xf000;
+		timers->TCFG1 |= 0x3000;
 
 		/* Enable autoreload and set the counter and compare
 		 * registers to values for the 500 Hz clock
 		 * (for a given  prescaler (15) and divider (16)):
 		 * counter = (66000000 / 500) >> 9;
 		 */
-		rTCNTB3 = 0x101;
-		rTCMPB3 = 0x101 / 2;
+		timers->ch[3].TCNTB = 0x101;
+		timers->ch[3].TCMPB = 0x101 / 2;
 
 		/* Start timer */
-		rTCON = (rTCON | UPDATE3 | RELOAD3) & ~INVERT3;
-		rTCON = (rTCON | START3) & ~UPDATE3;
+		timers->TCON = (timers->TCON | UPDATE3 | RELOAD3) & ~INVERT3;
+		timers->TCON = (timers->TCON | START3) & ~UPDATE3;
 	}
 #endif
 	/* If old board revision, then use vm-signal as cpld-clock */
-	rLCDCON2 = 0x00FFC000;
-	rLCDCON3 = 0x0007FF00;
-	rLCDCON4 = 0x00000000;
-	rLCDCON5 = 0x00000400;
-	rLCDCON1 = 0x00000B75;
+	lcd->LCDCON2 = 0x00FFC000;
+	lcd->LCDCON3 = 0x0007FF00;
+	lcd->LCDCON4 = 0x00000000;
+	lcd->LCDCON5 = 0x00000400;
+	lcd->LCDCON1 = 0x00000B75;
 	/* VM (GPD1) is used as clock for the CPLD */
-	rPDCON = (rPDCON & 0xFFFFFFF3) | 0x00000008;
+	gpio->PDCON = (gpio->PDCON & 0xFFFFFFF3) | 0x00000008;
 
 	return 0;
 }
@@ -425,6 +428,8 @@ int vfd_init_clocks (void)
  */
 int drv_vfd_init(void)
 {
+	S3C24X0_LCD * const lcd = S3C24X0_GetBase_LCD();
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
 	char *tmp;
 	ulong palette;
 	static int vfd_init_done = 0;
@@ -481,40 +486,40 @@ int drv_vfd_init(void)
 	 * see manual S3C2400
 	 */
 	/* Stopp LCD-Controller */
-	rLCDCON1 = 0x00000000;
+	lcd->LCDCON1 = 0x00000000;
 	/* frame buffer startadr */
-	rLCDSADDR1 = gd->fb_base >> 1;
+	lcd->LCDSADDR1 = gd->fb_base >> 1;
  	/* frame buffer endadr */
-	rLCDSADDR2 = (gd->fb_base + FRAME_BUF_SIZE) >> 1;
-	rLCDSADDR3 = ((256/4));
-rLCDCON2 = 0x000DC000;
+	lcd->LCDSADDR2 = (gd->fb_base + FRAME_BUF_SIZE) >> 1;
+	lcd->LCDSADDR3 = ((256/4));
+	lcd->LCDCON2 = 0x000DC000;
 	if(gd->vfd_type == VFD_TYPE_MN11236)
-		rLCDCON2 = 37 << 14;	/* MN11236: 38 lines */
+		lcd->LCDCON2 = 37 << 14;	/* MN11236: 38 lines */
 	else
-		rLCDCON2 = 55 << 14;	/* T119C:   56 lines */
-	rLCDCON3 = 0x0051000A;
-	rLCDCON4 = 0x00000001;
+		lcd->LCDCON2 = 55 << 14;	/* T119C:   56 lines */
+	lcd->LCDCON3 = 0x0051000A;
+	lcd->LCDCON4 = 0x00000001;
 	if (gd->vfd_type && vfd_inv_data)
-		rLCDCON5 = 0x000004C0;
+		lcd->LCDCON5 = 0x000004C0;
 	else
-		rLCDCON5 = 0x00000440;
+		lcd->LCDCON5 = 0x00000440;
 
 	/* Port pins as LCD output */
-	rPCCON =   (rPCCON & 0xFFFFFF00)| 0x000000AA;
-	rPDCON =   (rPDCON & 0xFFFFFF03)| 0x000000A8;
+	gpio->PCCON =   (gpio->PCCON & 0xFFFFFF00)| 0x000000AA;
+	gpio->PDCON =   (gpio->PDCON & 0xFFFFFF03)| 0x000000A8;
 
 	/* Synchronize VFD enable with LCD controller to avoid flicker	*/
-	rLCDCON1 = 0x00000B75;			/* Start LCD-Controller	*/
-	while((rLCDCON5 & 0x180000)!=0x100000);	/* Wait for end of VSYNC */
-	while((rLCDCON5 & 0x060000)!=0x040000);	/* Wait for next HSYNC	*/
-	while((rLCDCON5 & 0x060000)==0x040000);
-	while((rLCDCON5 & 0x060000)!=0x000000);
+	lcd->LCDCON1 = 0x00000B75;			/* Start LCD-Controller	*/
+	while((lcd->LCDCON5 & 0x180000)!=0x100000);	/* Wait for end of VSYNC */
+	while((lcd->LCDCON5 & 0x060000)!=0x040000);	/* Wait for next HSYNC	*/
+	while((lcd->LCDCON5 & 0x060000)==0x040000);
+	while((lcd->LCDCON5 & 0x060000)!=0x000000);
 	if(gd->vfd_type)
 		VFD_ENABLE;
 
-	debug ("LCDSADDR1: %lX\n", rLCDSADDR1);
-	debug ("LCDSADDR2: %lX\n", rLCDSADDR2);
-	debug ("LCDSADDR3: %lX\n", rLCDSADDR3);
+	debug ("LCDSADDR1: %lX\n", lcd->LCDSADDR1);
+	debug ("LCDSADDR2: %lX\n", lcd->LCDSADDR2);
+	debug ("LCDSADDR3: %lX\n", lcd->LCDSADDR3);
 
 	return 0;
 }
@@ -525,9 +530,11 @@ rLCDCON2 = 0x000DC000;
  */
 void disable_vfd (void)
 {
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
 	VFD_DISABLE;
-	rPDCON &= ~0xC;
-	rPDUP  &= ~0x2;
+	gpio->PDCON &= ~0xC;
+	gpio->PDUP  &= ~0x2;
 }
 
 /************************************************************************/