arm: spear: x600: Add support for Micrel KSZ9031 PHY

As the old ethernet PHY is not available any more, the x600 board has
been redesigned with the Micrel KSZ9031 PHY. This patch adds support
to autodetect the PHY and configure the Micrel PHY correctly.

Signed-off-by: Stefan Roese <sr@denx.de>

1 files changed, 59 insertions, 21 deletions

diff --git a/board/spear/x600/x600.c b/board/spear/x600/x600.c
index b8edfcd..f8e9fdd 100644
--- a/board/spear/x600/x600.c
+++ b/board/spear/x600/x600.c
@@ -8,6 +8,7 @@
  */
 
 #include <common.h>
+#include <micrel.h>
 #include <nand.h>
 #include <netdev.h>
 #include <phy.h>
@@ -69,27 +70,64 @@ void board_nand_init(void)
 
 int board_phy_config(struct phy_device *phydev)
 {
-	/* Extended PHY control 1, select GMII */
-	phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020);
-
-	/* Software reset necessary after GMII mode selction */
-	phy_reset(phydev);
-
-	/* Enable extended page register access */
-	phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001);
-
-	/* 17e: Enhanced LED behavior, needs to be written twice */
-	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
-	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
-
-	/* 16e: Enhanced LED method select */
-	phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea);
-
-	/* Disable extended page register access */
-	phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000);
-
-	/* Enable clock output pin */
-	phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049);
+	unsigned short id1, id2;
+
+	/* check whether KSZ9031 or AR8035 has to be configured */
+	id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2);
+	id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3);
+
+	if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) {
+		/* PHY configuration for Micrel KSZ9031 */
+		printf("PHY KSZ9031 detected - ");
+
+		phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, 0x1c00);
+
+		/* control data pad skew - devaddr = 0x02, register = 0x04 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x0000);
+		/* rx data pad skew - devaddr = 0x02, register = 0x05 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x0000);
+		/* tx data pad skew - devaddr = 0x02, register = 0x05 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x0000);
+		/* gtx and rx clock pad skew - devaddr = 0x02, reg = 0x08 */
+		ksz9031_phy_extended_write(phydev, 0x02,
+					   MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
+					   MII_KSZ9031_MOD_DATA_NO_POST_INC,
+					   0x03FF);
+	} else {
+		/* PHY configuration for Vitesse VSC8641 */
+		printf("PHY VSC8641 detected - ");
+
+		/* Extended PHY control 1, select GMII */
+		phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020);
+
+		/* Software reset necessary after GMII mode selction */
+		phy_reset(phydev);
+
+		/* Enable extended page register access */
+		phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001);
+
+		/* 17e: Enhanced LED behavior, needs to be written twice */
+		phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
+		phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
+
+		/* 16e: Enhanced LED method select */
+		phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea);
+
+		/* Disable extended page register access */
+		phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000);
+
+		/* Enable clock output pin */
+		phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049);
+	}
 
 	if (phydev->drv->config)
 		phydev->drv->config(phydev);