summaryrefslogtreecommitdiff
path: root/board/silica
diff options
context:
space:
mode:
authorLothar Felten <lothar.felten@gmail.com>2014-01-31 17:34:14 +0100
committerTom Rini <trini@ti.com>2014-02-21 13:54:57 -0500
commitda4105dfcd27c20e5cf4eb750f88938f56620d37 (patch)
treec0a412767dbccf65710c09774623c7713bebc28d /board/silica
parent3e11350255d9c5d4bd03c2a65769da84c05d3294 (diff)
downloadu-boot-imx-da4105dfcd27c20e5cf4eb750f88938f56620d37.zip
u-boot-imx-da4105dfcd27c20e5cf4eb750f88938f56620d37.tar.gz
u-boot-imx-da4105dfcd27c20e5cf4eb750f88938f56620d37.tar.bz2
am335x: Initial support for Silica Pengwyn board
This patch add support for the Silica Pengwyn board [1] The board is based on a TI AM3354 CPU [2] All jumpers removed it will boot from the SDcard, the console is on UART1 accessible via the FDTI -> USB. The on board NAND flash is supported and can act as boot medium, depending on jumper settings. USB Host, USB Device and Ethernet are also provided but untested. [1] http://www.silica.com/product/silica-pengwyn-board.html [2] http://www.ti.com/product/am3354 Signed-off-by: Lothar Felten <lothar.felten@gmail.com> [trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused spi0_pin_mux from Pengwyn support] Signed-off-by: Tom Rini <trini@ti.com>
Diffstat (limited to 'board/silica')
-rw-r--r--board/silica/pengwyn/Makefile13
-rw-r--r--board/silica/pengwyn/board.c207
-rw-r--r--board/silica/pengwyn/board.h15
-rw-r--r--board/silica/pengwyn/mux.c98
4 files changed, 333 insertions, 0 deletions
diff --git a/board/silica/pengwyn/Makefile b/board/silica/pengwyn/Makefile
new file mode 100644
index 0000000..c8b4f9a
--- /dev/null
+++ b/board/silica/pengwyn/Makefile
@@ -0,0 +1,13 @@
+#
+# Makefile
+#
+# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_NOR_BOOT),y)
+obj-y := mux.o
+endif
+
+obj-y += board.o
diff --git a/board/silica/pengwyn/board.c b/board/silica/pengwyn/board.c
new file mode 100644
index 0000000..a553129
--- /dev/null
+++ b/board/silica/pengwyn/board.c
@@ -0,0 +1,207 @@
+/*
+ * board.c
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+#include <phy.h>
+#include <cpsw.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+#if defined(CONFIG_SPL_BUILD)
+
+/* DDR3 RAM timings */
+static const struct ddr_data ddr3_data = {
+ .datardsratio0 = MT41K128MJT187E_RD_DQS,
+ .datawdsratio0 = MT41K128MJT187E_WR_DQS,
+ .datafwsratio0 = MT41K128MJT187E_PHY_FIFO_WE,
+ .datawrsratio0 = MT41K128MJT187E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+ .cmd0csratio = MT41K128MJT187E_RATIO,
+ .cmd0iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+ .cmd1csratio = MT41K128MJT187E_RATIO,
+ .cmd1iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+ .cmd2csratio = MT41K128MJT187E_RATIO,
+ .cmd2iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+ .sdram_config = MT41K128MJT187E_EMIF_SDCFG,
+ .ref_ctrl = MT41K128MJT187E_EMIF_SDREF,
+ .sdram_tim1 = MT41K128MJT187E_EMIF_TIM1,
+ .sdram_tim2 = MT41K128MJT187E_EMIF_TIM2,
+ .sdram_tim3 = MT41K128MJT187E_EMIF_TIM3,
+ .zq_config = MT41K128MJT187E_ZQ_CFG,
+ .emif_ddr_phy_ctlr_1 = MT41K128MJT187E_EMIF_READ_LATENCY |
+ PHY_EN_DYN_PWRDN,
+};
+
+const struct ctrl_ioregs ddr3_ioregs = {
+ .cm0ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+ .cm1ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+ .cm2ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+ .dt0ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+ .dt1ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+ /* break into full u-boot on 'c' */
+ return serial_tstc() && serial_getc() == 'c';
+}
+#endif
+
+#define OSC (V_OSCK/1000000)
+const struct dpll_params dpll_ddr_266 = {
+ 266, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_303 = {
+ 303, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_400 = {
+ 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+ /*
+ * The pengwyn board uses the TPS650250 PMIC without I2C
+ * interface and will output the following fixed voltages:
+ * DCDC1=3V3 (IO) DCDC2=1V5 (DDR) DCDC3=1V26 (Vmpu)
+ * VLDO1=1V8 (IO) VLDO2=1V8(IO)
+ * Vcore=1V1 is fixed, generated by TPS62231
+ */
+
+ /* Get the frequency */
+ dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+
+ /* Set CORE Frequencies to OPP100 */
+ do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+ /* 720MHz cpu, this might change on newer board revisions */
+ dpll_mpu_opp100.m = MPUPLL_M_720;
+ do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+ /* future configs can return other clock settings */
+ return &dpll_ddr_303;
+}
+
+void set_uart_mux_conf(void)
+{
+ enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+ enable_board_pin_mux();
+}
+
+void sdram_init(void)
+{
+ config_ddr(303, &ddr3_ioregs, &ddr3_data,
+ &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
+}
+#endif /* if CONFIG_SPL_BUILD */
+
+/*
+ * Basic board specific setup. Pinmux has been handled already.
+ */
+int board_init(void)
+{
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+ gpmc_init();
+ return 0;
+}
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static void cpsw_control(int enabled)
+{
+ /* VTP can be added here */
+ return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+ {
+ .slave_reg_ofs = 0x208,
+ .sliver_reg_ofs = 0xd80,
+ .phy_id = 0,
+ .phy_if = PHY_INTERFACE_MODE_MII,
+ },
+ {
+ .slave_reg_ofs = 0x308,
+ .sliver_reg_ofs = 0xdc0,
+ .phy_id = 1,
+ .phy_if = PHY_INTERFACE_MODE_MII,
+ },
+};
+
+static struct cpsw_platform_data cpsw_data = {
+ .mdio_base = CPSW_MDIO_BASE,
+ .cpsw_base = CPSW_BASE,
+ .mdio_div = 0xff,
+ .channels = 8,
+ .cpdma_reg_ofs = 0x800,
+ .slaves = 1,
+ .slave_data = cpsw_slaves,
+ .ale_reg_ofs = 0xd00,
+ .ale_entries = 1024,
+ .host_port_reg_ofs = 0x108,
+ .hw_stats_reg_ofs = 0x900,
+ .bd_ram_ofs = 0x2000,
+ .mac_control = (1 << 5),
+ .control = cpsw_control,
+ .host_port_num = 0,
+ .version = CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+ int rv, n = 0;
+ uint8_t mac_addr[6];
+ uint32_t mac_hi, mac_lo;
+
+ if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+ printf("<ethaddr> not set. Reading from E-fuse\n");
+ /* try reading mac address from efuse */
+ mac_lo = readl(&cdev->macid0l);
+ mac_hi = readl(&cdev->macid0h);
+ mac_addr[0] = mac_hi & 0xFF;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+ mac_addr[4] = mac_lo & 0xFF;
+ mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+ if (is_valid_ether_addr(mac_addr))
+ eth_setenv_enetaddr("ethaddr", mac_addr);
+ else
+ return n;
+ }
+
+ writel(MII_MODE_ENABLE, &cdev->miisel);
+
+ rv = cpsw_register(&cpsw_data);
+ if (rv < 0)
+ printf("Error %d registering CPSW switch\n", rv);
+ else
+ n += rv;
+ return n;
+}
+#endif /* if CONFIG_DRIVER_TI_CPSW */
diff --git a/board/silica/pengwyn/board.h b/board/silica/pengwyn/board.h
new file mode 100644
index 0000000..05addf6
--- /dev/null
+++ b/board/silica/pengwyn/board.h
@@ -0,0 +1,15 @@
+/*
+ * board.h
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+void enable_uart0_pin_mux(void);
+void enable_board_pin_mux(void);
+
+#endif
diff --git a/board/silica/pengwyn/mux.c b/board/silica/pengwyn/mux.c
new file mode 100644
index 0000000..c8be440
--- /dev/null
+++ b/board/silica/pengwyn/mux.c
@@ -0,0 +1,98 @@
+/*
+ * mux.c
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include "board.h"
+
+/* UART0 pins E15(rx),E16(tx) [E17(rts),E18(cts)] */
+static struct module_pin_mux uart0_pin_mux[] = {
+ {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */
+ {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */
+ {-1},
+};
+
+/* unused: UART1 pins D15(tx),D16(rx),D17(cts),D18(rts) */
+
+/* I2C pins C16(scl)/C17(sda) */
+static struct module_pin_mux i2c0_pin_mux[] = {
+ {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
+ PULLUDEN | SLEWCTRL)}, /* I2C0_DATA */
+ {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
+ PULLUDEN | SLEWCTRL)}, /* I2C0_SCLK */
+ {-1},
+};
+
+/* MMC0 pins */
+static struct module_pin_mux mmc0_pin_mux[] = {
+ {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */
+ {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */
+ {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */
+ {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */
+ {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CLK */
+ {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CMD */
+ {OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)}, /* MMC0_CD */
+ {-1},
+};
+
+/* MII pins */
+static struct module_pin_mux mii1_pin_mux[] = {
+ {OFFSET(mii1_rxerr), MODE(0) | RXACTIVE}, /* MII1_RXERR */
+ {OFFSET(mii1_txen), MODE(0)}, /* MII1_TXEN */
+ {OFFSET(mii1_rxdv), MODE(0) | RXACTIVE}, /* MII1_RXDV */
+ {OFFSET(mii1_txd3), MODE(0)}, /* MII1_TXD3 */
+ {OFFSET(mii1_txd2), MODE(0)}, /* MII1_TXD2 */
+ {OFFSET(mii1_txd1), MODE(0)}, /* MII1_TXD1 */
+ {OFFSET(mii1_txd0), MODE(0)}, /* MII1_TXD0 */
+ {OFFSET(mii1_txclk), MODE(0) | RXACTIVE}, /* MII1_TXCLK */
+ {OFFSET(mii1_rxclk), MODE(0) | RXACTIVE}, /* MII1_RXCLK */
+ {OFFSET(mii1_rxd3), MODE(0) | RXACTIVE}, /* MII1_RXD3 */
+ {OFFSET(mii1_rxd2), MODE(0) | RXACTIVE}, /* MII1_RXD2 */
+ {OFFSET(mii1_rxd1), MODE(0) | RXACTIVE}, /* MII1_RXD1 */
+ {OFFSET(mii1_rxd0), MODE(0) | RXACTIVE}, /* MII1_RXD0 */
+ {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
+ {-1},
+};
+
+/* NAND pins */
+static struct module_pin_mux nand_pin_mux[] = {
+ {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
+ {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
+ {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
+ {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
+ {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
+ {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
+ {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
+ {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
+ {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+ {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
+ {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
+ {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+ {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
+ {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
+ {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
+ {-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+ configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_board_pin_mux()
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+ configure_module_pin_mux(uart0_pin_mux);
+ configure_module_pin_mux(mii1_pin_mux);
+ configure_module_pin_mux(mmc0_pin_mux);
+ configure_module_pin_mux(nand_pin_mux);
+}