dm: exynos: Make sure that GPIOs are requested

With driver model GPIOs must be requested before use. Make sure this is
done correctly.

(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)

Signed-off-by: Simon Glass <sjg@chromium.org>

8 files changed, 53 insertions, 8 deletions

diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c
index e39795d..881d080 100644
--- a/board/samsung/arndale/arndale.c
+++ b/board/samsung/arndale/arndale.c
@@ -19,6 +19,8 @@ int board_usb_init(int index, enum usb_init_type init)
 	/* Configure gpios for usb 3503 hub:
 	 * disconnect, toggle reset and connect
 	 */
+	gpio_request(EXYNOS5_GPIO_D17, "usb_connect");
+	gpio_request(EXYNOS5_GPIO_X35, "usb_reset");
 	gpio_direction_output(EXYNOS5_GPIO_D17, 0);
 	gpio_direction_output(EXYNOS5_GPIO_X35, 0);
 
diff --git a/board/samsung/common/misc.c b/board/samsung/common/misc.c
index b935922..4538ac7 100644
--- a/board/samsung/common/misc.c
+++ b/board/samsung/common/misc.c
@@ -411,6 +411,8 @@ void check_boot_mode(void)
 void keys_init(void)
 {
 	/* Set direction to input */
+	gpio_request(KEY_VOL_UP_GPIO, "volume-up");
+	gpio_request(KEY_VOL_DOWN_GPIO, "volume-down");
 	gpio_direction_input(KEY_VOL_UP_GPIO);
 	gpio_direction_input(KEY_VOL_DOWN_GPIO);
 }
diff --git a/board/samsung/goni/goni.c b/board/samsung/goni/goni.c
index 4cee78b..58cf96e 100644
--- a/board/samsung/goni/goni.c
+++ b/board/samsung/goni/goni.c
@@ -90,6 +90,7 @@ int board_mmc_init(bd_t *bis)
 	int i, ret, ret_sd = 0;
 
 	/* MASSMEMORY_EN: XMSMDATA7: GPJ2[7] output high */
+	gpio_request(S5PC110_GPIO_J27, "massmemory_en");
 	gpio_direction_output(S5PC110_GPIO_J27, 1);
 
 	/*
@@ -118,6 +119,7 @@ int board_mmc_init(bd_t *bis)
 	 * SD card (T_FLASH) detect and init
 	 * T_FLASH_DETECT: EINT28: GPH3[4] input mode
 	 */
+	gpio_request(S5PC110_GPIO_H34, "t_flash_detect");
 	gpio_cfg_pin(S5PC110_GPIO_H34, S5P_GPIO_INPUT);
 	gpio_set_pull(S5PC110_GPIO_H34, S5P_GPIO_PULL_UP);
 
diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
index d6ce133..53ff706 100644
--- a/board/samsung/smdk5250/exynos5-dt.c
+++ b/board/samsung/smdk5250/exynos5-dt.c
@@ -29,6 +29,7 @@ DECLARE_GLOBAL_DATA_PTR;
 static void board_enable_audio_codec(void)
 {
 	/* Enable MAX98095 Codec */
+	gpio_request(EXYNOS5_GPIO_X17, "max98095_enable");
 	gpio_direction_output(EXYNOS5_GPIO_X17, 1);
 	gpio_set_pull(EXYNOS5_GPIO_X17, S5P_GPIO_PULL_NONE);
 }
@@ -199,16 +200,19 @@ static int board_dp_bridge_setup(void)
 	/* Setup the GPIOs */
 
 	/* PD is ACTIVE_LOW, and initially de-asserted */
+	gpio_request(EXYNOS5_GPIO_Y25, "dp_bridge_pd");
 	gpio_set_pull(EXYNOS5_GPIO_Y25, S5P_GPIO_PULL_NONE);
 	gpio_direction_output(EXYNOS5_GPIO_Y25, 1);
 
 	/* Reset is ACTIVE_LOW */
+	gpio_request(EXYNOS5_GPIO_X15, "dp_bridge_reset");
 	gpio_set_pull(EXYNOS5_GPIO_X15, S5P_GPIO_PULL_NONE);
 	gpio_direction_output(EXYNOS5_GPIO_X15, 0);
 
 	udelay(10);
 	gpio_set_value(EXYNOS5_GPIO_X15, 1);
 
+	gpio_request(EXYNOS5_GPIO_X07, "dp_bridge_hpd");
 	gpio_direction_input(EXYNOS5_GPIO_X07);
 
 	/*
@@ -236,10 +240,12 @@ static int board_dp_bridge_setup(void)
 void exynos_cfg_lcd_gpio(void)
 {
 	/* For Backlight */
+	gpio_request(EXYNOS5_GPIO_B20, "lcd_backlight");
 	gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT);
 	gpio_set_value(EXYNOS5_GPIO_B20, 1);
 
 	/* LCD power on */
+	gpio_request(EXYNOS5_GPIO_X15, "lcd_power");
 	gpio_cfg_pin(EXYNOS5_GPIO_X15, S5P_GPIO_OUTPUT);
 	gpio_set_value(EXYNOS5_GPIO_X15, 1);
 
@@ -276,6 +282,7 @@ void exynos_backlight_on(unsigned int on)
 	mdelay(10);
 
 	/* board_dp_backlight_en */
+	gpio_request(EXYNOS5_GPIO_X30, "board_dp_backlight_en");
 	gpio_direction_output(EXYNOS5_GPIO_X30, 1);
 #endif
 }
diff --git a/board/samsung/smdk5420/smdk5420.c b/board/samsung/smdk5420/smdk5420.c
index 47998ab..a691222 100644
--- a/board/samsung/smdk5420/smdk5420.c
+++ b/board/samsung/smdk5420/smdk5420.c
@@ -74,9 +74,12 @@ void exynos_lcd_power_on(void)
 	mdelay(5);
 
 	/* TODO(ajaykumar.rs@samsung.com): Use device tree */
+	gpio_request(EXYNOS5420_GPIO_X35, "edp_slp#");
 	gpio_direction_output(EXYNOS5420_GPIO_X35, 1);	/* EDP_SLP# */
 	mdelay(10);
+	gpio_request(EXYNOS5420_GPIO_Y77, "edp_rst#");
 	gpio_direction_output(EXYNOS5420_GPIO_Y77, 1);	/* EDP_RST# */
+	gpio_request(EXYNOS5420_GPIO_X26, "edp_hpd");
 	gpio_direction_input(EXYNOS5420_GPIO_X26);	/* EDP_HPD */
 	gpio_set_pull(EXYNOS5420_GPIO_X26, S5P_GPIO_PULL_NONE);
 
@@ -88,6 +91,7 @@ void exynos_lcd_power_on(void)
 void exynos_backlight_on(unsigned int onoff)
 {
 	/* For PWM */
+	gpio_request(EXYNOS5420_GPIO_B20, "backlight_on");
 	gpio_cfg_pin(EXYNOS5420_GPIO_B20, S5P_GPIO_FUNC(0x1));
 	gpio_set_value(EXYNOS5420_GPIO_B20, 1);
 
diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
index 9e76b5d..e163e45 100644
--- a/board/samsung/trats/trats.c
+++ b/board/samsung/trats/trats.c
@@ -63,6 +63,8 @@ void i2c_init_board(void)
 	}
 
 	/* I2C_8 -> FG */
+	gpio_request(EXYNOS4_GPIO_Y40, "i2c_clk");
+	gpio_request(EXYNOS4_GPIO_Y41, "i2c_data");
 	gpio_direction_output(EXYNOS4_GPIO_Y40, 1);
 	gpio_direction_output(EXYNOS4_GPIO_Y41, 1);
 }
@@ -346,12 +348,17 @@ int exynos_power_init(void)
 static unsigned int get_hw_revision(void)
 {
 	int hwrev = 0;
+	char str[10];
 	int i;
 
 	/* hw_rev[3:0] == GPE1[3:0] */
-	for (i = EXYNOS4_GPIO_E10; i < EXYNOS4_GPIO_E14; i++) {
-		gpio_cfg_pin(i, S5P_GPIO_INPUT);
-		gpio_set_pull(i, S5P_GPIO_PULL_NONE);
+	for (i = 0; i < 4; i++) {
+		int pin = i + EXYNOS4_GPIO_E10;
+
+		sprintf(str, "hw_rev%d", i);
+		gpio_request(pin, str);
+		gpio_cfg_pin(pin, S5P_GPIO_INPUT);
+		gpio_set_pull(pin, S5P_GPIO_PULL_NONE);
 	}
 
 	udelay(1);
@@ -517,6 +524,7 @@ static void board_power_init(void)
 static void exynos_uart_init(void)
 {
 	/* UART_SEL GPY4[7] (part2) at EXYNOS4 */
+	gpio_request(EXYNOS4_GPIO_Y47, "uart_sel");
 	gpio_set_pull(EXYNOS4_GPIO_Y47, S5P_GPIO_PULL_UP);
 	gpio_direction_output(EXYNOS4_GPIO_Y47, 1);
 }
@@ -534,6 +542,7 @@ int exynos_early_init_f(void)
 
 void exynos_reset_lcd(void)
 {
+	gpio_request(EXYNOS4_GPIO_Y45, "lcd_reset");
 	gpio_direction_output(EXYNOS4_GPIO_Y45, 1);
 	udelay(10000);
 	gpio_direction_output(EXYNOS4_GPIO_Y45, 0);
diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c
index 2924ee6..a737749 100644
--- a/board/samsung/trats2/trats2.c
+++ b/board/samsung/trats2/trats2.c
@@ -33,6 +33,7 @@ static inline u32 get_model_rev(void);
 static void check_hw_revision(void)
 {
 	int modelrev = 0;
+	char str[12];
 	int i;
 
 	/*
@@ -41,13 +42,22 @@ static void check_hw_revision(void)
 	 * TRM say that it may cause unexcepted state and leakage current.
 	 * and pull-none is only for output function.
 	 */
-	for (i = EXYNOS4X12_GPIO_M10; i < EXYNOS4X12_GPIO_M12; i++)
-		gpio_cfg_pin(i, S5P_GPIO_INPUT);
+	for (i = 0; i < 2; i++) {
+		int pin = i + EXYNOS4X12_GPIO_M10;
+
+		sprintf(str, "model_rev%d", i);
+		gpio_request(pin, str);
+		gpio_cfg_pin(pin, S5P_GPIO_INPUT);
+	}
 
 	/* GPM1[5:2]: HW_REV[3:0] */
-	for (i = EXYNOS4X12_GPIO_M12; i < EXYNOS4X12_GPIO_M16; i++) {
-		gpio_cfg_pin(i, S5P_GPIO_INPUT);
-		gpio_set_pull(i, S5P_GPIO_PULL_NONE);
+	for (i = 0; i < 4; i++) {
+		int pin = i + EXYNOS4X12_GPIO_M12;
+
+		sprintf(str, "hw_rev%d", i);
+		gpio_request(pin, str);
+		gpio_cfg_pin(pin, S5P_GPIO_INPUT);
+		gpio_set_pull(pin, S5P_GPIO_PULL_NONE);
 	}
 
 	/* GPM1[1:0]: MODEL_REV[1:0] */
@@ -103,10 +113,14 @@ static void board_init_i2c(void)
 	}
 
 	/* I2C_8 */
+	gpio_request(EXYNOS4X12_GPIO_F14, "i2c8_clk");
+	gpio_request(EXYNOS4X12_GPIO_F15, "i2c8_data");
 	gpio_direction_output(EXYNOS4X12_GPIO_F14, 1);
 	gpio_direction_output(EXYNOS4X12_GPIO_F15, 1);
 
 	/* I2C_9 */
+	gpio_request(EXYNOS4X12_GPIO_M21, "i2c9_clk");
+	gpio_request(EXYNOS4X12_GPIO_M20, "i2c9_data");
 	gpio_direction_output(EXYNOS4X12_GPIO_M21, 1);
 	gpio_direction_output(EXYNOS4X12_GPIO_M20, 1);
 }
@@ -388,6 +402,7 @@ void exynos_lcd_power_on(void)
 	struct pmic *p = pmic_get("MAX77686_PMIC");
 
 	/* LCD_2.2V_EN: GPC0[1] */
+	gpio_request(EXYNOS4X12_GPIO_C01, "lcd_2v2_en");
 	gpio_set_pull(EXYNOS4X12_GPIO_C01, S5P_GPIO_PULL_UP);
 	gpio_direction_output(EXYNOS4X12_GPIO_C01, 1);
 
@@ -400,6 +415,7 @@ void exynos_lcd_power_on(void)
 void exynos_reset_lcd(void)
 {
 	/* reset lcd */
+	gpio_request(EXYNOS4X12_GPIO_F21, "lcd_reset");
 	gpio_direction_output(EXYNOS4X12_GPIO_F21, 0);
 	udelay(10);
 	gpio_set_value(EXYNOS4X12_GPIO_F21, 1);
diff --git a/board/samsung/universal_c210/universal.c b/board/samsung/universal_c210/universal.c
index f9d3325..c04f48c 100644
--- a/board/samsung/universal_c210/universal.c
+++ b/board/samsung/universal_c210/universal.c
@@ -330,6 +330,7 @@ void exynos_cfg_lcd_gpio(void)
 	}
 
 	/* gpio pad configuration for LCD reset. */
+	gpio_request(EXYNOS4_GPIO_Y45, "lcd_reset");
 	gpio_cfg_pin(EXYNOS4_GPIO_Y45, S5P_GPIO_OUTPUT);
 
 	spi_init();
@@ -386,6 +387,7 @@ int exynos_init(void)
 		 * you should set it HIGH since it removes the inverter
 		 */
 		/* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */
+		gpio_request(EXYNOS4_GPIO_E36, "ldo_en");
 		gpio_direction_output(EXYNOS4_GPIO_E36, 0);
 		break;
 	default:
@@ -394,6 +396,7 @@ int exynos_init(void)
 		 * But set it as HIGH to ensure
 		 */
 		/* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */
+		gpio_request(EXYNOS4_GPIO_E13, "massmemory_en");
 		gpio_direction_output(EXYNOS4_GPIO_E13, 1);
 		break;
 	}