Merge with /home/wd/git/u-boot/master

2 files changed, 167 insertions, 1 deletions

diff --git a/board/mbx8xx/Makefile b/board/mbx8xx/Makefile
index 3e8376c..e4d1099 100644
--- a/board/mbx8xx/Makefile
+++ b/board/mbx8xx/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o vpd.o
+OBJS	= $(BOARD).o flash.o vpd.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
diff --git a/board/mbx8xx/pcmcia.c b/board/mbx8xx/pcmcia.c
new file mode 100644
index 0000000..132a688
--- /dev/null
+++ b/board/mbx8xx/pcmcia.c
@@ -0,0 +1,166 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#include "csr.h"
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+/* A lot of this has been taken from the RPX code in this file it works from me.
+   I have added the voltage selection for the MBX board. */
+
+/* MBX voltage bit in control register #2 */
+#define CR2_VPP12       ((uchar)0x10)
+#define CR2_VPPVDD      ((uchar)0x20)
+#define CR2_VDD5        ((uchar)0x40)
+#define CR2_VDD3        ((uchar)0x80)
+
+#define PCMCIA_BOARD_MSG "MBX860"
+
+int pcmcia_voltage_set (int slot, int vcc, int vpp)
+{
+	uchar reg = 0;
+
+	debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	       'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
+
+	switch (vcc) {
+		case 0:
+			break;
+		case 33:
+			reg |= CR2_VDD3;
+			break;
+		case 50:
+			reg |= CR2_VDD5;
+			break;
+		default:
+			return 1;
+	}
+
+	switch (vpp) {
+		case 0:
+			break;
+		case 33:
+		case 50:
+			if (vcc == vpp) {
+				reg |= CR2_VPPVDD;
+			} else {
+				return 1;
+			}
+			break;
+		case 120:
+			reg |= CR2_VPP12;
+			break;
+		default:
+			return 1;
+	}
+
+	/* first, turn off all power */
+	MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
+
+	/* enable new powersettings */
+	MBX_CSR2 |= reg;
+	debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
+
+	return (0);
+}
+
+int pcmcia_hardware_enable (int slot)
+{
+	volatile immap_t *immap;
+	volatile cpm8xx_t *cp;
+	volatile pcmconf8xx_t *pcmp;
+	volatile sysconf8xx_t *sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
+	       'A' + slot);
+
+	udelay (10000);
+
+	immap = (immap_t *) CFG_IMMR;
+	sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
+	pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
+	cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;	/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+	udelay (500);
+
+	/* remove all power */
+	pcmcia_voltage_set (slot, 0, 0);
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+#ifndef CONFIG_HMI10
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+#else
+	if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
+#endif	/* CONFIG_HMI10 */
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
+	reg = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
+	       (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
+	       (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
+
+	if ((reg & mask) == mask) {
+		pcmcia_voltage_set (_slot_, 50, 0);
+		printf (" 5.0V card found: ");
+	} else {
+		pcmcia_voltage_set (_slot_, 33, 0);
+		printf (" 3.3V card found: ");
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg = PCMCIA_PGCRX (_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;	/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+
+	udelay (250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+	}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable (int slot)
+{
+	return 0;	/* No hardware to disable */
+}
+#endif /* CFG_CMD_PCMCIA */
+
+#endif	/* CONFIG_PCMCIA */