TI:omap3: Drop omap3_zoom2

The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.

Signed-off-by: Tom Rini <trini@ti.com>

1 files changed, 0 insertions, 130 deletions

diff --git a/board/logicpd/zoom2/zoom2_serial.c b/board/logicpd/zoom2/zoom2_serial.c
deleted file mode 100644
index 2959276..0000000
--- a/board/logicpd/zoom2/zoom2_serial.c
+++ /dev/null
@@ -1,130 +0,0 @@
-/*
- * Copyright (c) 2009 Wind River Systems, Inc.
- * Tom Rix <Tom.Rix@windriver.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- *
- * This file was adapted from arch/powerpc/cpu/mpc5xxx/serial.c
- */
-
-#include <common.h>
-#include <serial.h>
-#include <ns16550.h>
-#include <asm/arch/cpu.h>
-#include "zoom2_serial.h"
-
-int quad_init_dev (unsigned long base)
-{
-	/*
-	 * The Quad UART is on the debug board.
-	 * Check if the debug board is attached before using the UART
-	 */
-	if (zoom2_debug_board_connected ()) {
-		NS16550_t com_port = (NS16550_t) base;
-		int baud_divisor = CONFIG_SYS_NS16550_CLK / 16 /
-			CONFIG_BAUDRATE;
-
-		/*
-		 * Zoom2 has a board specific initialization of its UART.
-		 * This generic initialization has been copied from
-		 * drivers/serial/ns16550.c. The macros have been expanded.
-		 *
-		 * Do the following instead of
-		 *
-		 * NS16550_init (com_port, clock_divisor);
-		 */
-		com_port->ier = 0x00;
-
-		/*
-		 * On Zoom2 board Set pre-scalar to 1
-		 * CLKSEL is GND => MCR[7] is 1 => preslr is 4
-		 * So change the prescl to 1
-		 */
-		com_port->lcr = 0xBF;
-		com_port->fcr |= 0x10;
-		com_port->mcr &= 0x7F;
-
-		/* This is generic ns16550.c setup */
-		com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1;
-		com_port->dll = 0;
-		com_port->dlm = 0;
-		com_port->lcr = UART_LCR_8N1;
-		com_port->mcr = UART_MCR_DTR | UART_MCR_RTS;
-		com_port->fcr = UART_FCR_FIFO_EN | UART_FCR_RXSR |
-			UART_FCR_TXSR;
-		com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1;
-		com_port->dll = baud_divisor & 0xff;
-		com_port->dlm = (baud_divisor >> 8) & 0xff;
-		com_port->lcr = UART_LCR_8N1;
-	}
-	/*
-	 * We have to lie here, otherwise the board init code will hang
-	 * on the check
-	 */
-	return 0;
-}
-
-void quad_putc_dev (unsigned long base, const char c)
-{
-	if (zoom2_debug_board_connected ()) {
-
-		if (c == '\n')
-			quad_putc_dev (base, '\r');
-
-		NS16550_putc ((NS16550_t) base, c);
-	} else {
-		usbtty_putc(c);
-	}
-}
-
-void quad_puts_dev (unsigned long base, const char *s)
-{
-	if (zoom2_debug_board_connected ()) {
-		while ((s != NULL) && (*s != '\0'))
-			quad_putc_dev (base, *s++);
-	} else {
-		usbtty_puts(s);
-	}
-}
-
-int quad_getc_dev (unsigned long base)
-{
-	if (zoom2_debug_board_connected ())
-		return NS16550_getc ((NS16550_t) base);
-
-	return usbtty_getc();
-}
-
-int quad_tstc_dev (unsigned long base)
-{
-	if (zoom2_debug_board_connected ())
-		return NS16550_tstc ((NS16550_t) base);
-
-	return usbtty_tstc();
-}
-
-void quad_setbrg_dev (unsigned long base)
-{
-	if (zoom2_debug_board_connected ()) {
-
-		int clock_divisor = CONFIG_SYS_NS16550_CLK / 16 /
-			CONFIG_BAUDRATE;
-
-		NS16550_reinit ((NS16550_t) base, clock_divisor);
-	}
-}
-
-QUAD_INIT (0)
-QUAD_INIT (1)
-QUAD_INIT (2)
-QUAD_INIT (3)
-
-struct serial_device *default_serial_console(void)
-{
-	switch (ZOOM2_DEFAULT_SERIAL_DEVICE) {
-	case 0: return &zoom2_serial_device0;
-	case 1: return &zoom2_serial_device1;
-	case 2: return &zoom2_serial_device2;
-	case 3: return &zoom2_serial_device3;
-	}
-}