mpc85xx: Add gdsys ControlCenter Digital board

The gdsys ControlCenter Digital board is based on a Freescale P1022 QorIQ SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2x GbE
- Lattice ECP3 FPGA connected via PCIe
- mSATA RAID1
- USB host
- DisplayPort video output
- Atmel TPM

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>

1 files changed, 71 insertions, 0 deletions

diff --git a/board/gdsys/p1022/ddr.c b/board/gdsys/p1022/ddr.c
new file mode 100644
index 0000000..4a652de
--- /dev/null
+++ b/board/gdsys/p1022/ddr.c
@@ -0,0 +1,71 @@
+/*
+ * Copyright 2010 Freescale Semiconductor, Inc.
+ * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
+ *          Timur Tabi <timur@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm,
+			   unsigned int ctrl_num)
+{
+	unsigned int i;
+
+	if (ctrl_num) {
+		printf("Wrong parameter for controller number %d", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	/* set odt_rd_cfg and odt_wr_cfg. */
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		popts->cs_local_opts[i].odt_rd_cfg = 0;
+		popts->cs_local_opts[i].odt_wr_cfg = 1;
+	}
+
+	popts->clk_adjust = 5;
+	popts->cpo_override = 0x1f;
+	popts->write_data_delay = 2;
+	popts->half_strength_driver_enable = 1;
+
+	/* Per AN4039, enable ZQ calibration. */
+	popts->zq_en = 1;
+}
+
+#ifdef CONFIG_SPD_EEPROM
+/*
+ * we only have a "fake" SPD-EEPROM here, which has 16 bit addresses
+ */
+void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address)
+{
+	int ret = i2c_read(i2c_address, 0, 2, (uchar *)spd,
+				sizeof(generic_spd_eeprom_t));
+
+	if (ret) {
+		if (i2c_address ==
+#ifdef SPD_EEPROM_ADDRESS
+				SPD_EEPROM_ADDRESS
+#elif defined(SPD_EEPROM_ADDRESS1)
+				SPD_EEPROM_ADDRESS1
+#endif
+				) {
+			printf("DDR: failed to read SPD from address %u\n",
+			       i2c_address);
+		} else {
+			debug("DDR: failed to read SPD from address %u\n",
+			      i2c_address);
+		}
+		memset(spd, 0, sizeof(generic_spd_eeprom_t));
+	}
+}
+#endif