Merge git://git.denx.de/u-boot

40 files changed, 2090 insertions, 92 deletions

diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 54cb098..36f7c4f 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -53,6 +53,7 @@ COBJS-$(CONFIG_P2020DS)		+= ics307_clk.o
 COBJS-$(CONFIG_P3041DS)		+= ics307_clk.o
 COBJS-$(CONFIG_P4080DS)		+= ics307_clk.o
 COBJS-$(CONFIG_P5020DS)		+= ics307_clk.o
+COBJS-$(CONFIG_VSC_CROSSBAR)    += vsc3316_3308.o
 
 # deal with common files for P-series corenet based devices
 SUBLIB-$(CONFIG_P2041RDB)	+= p_corenet/libp_corenet.o
diff --git a/board/freescale/common/ngpixis.c b/board/freescale/common/ngpixis.c
index 276ae3c..3c75028 100644
--- a/board/freescale/common/ngpixis.c
+++ b/board/freescale/common/ngpixis.c
@@ -237,13 +237,17 @@ int pixis_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 	return 0;
 }
 
-U_BOOT_CMD(
-	pixis_reset, CONFIG_SYS_MAXARGS, 1, pixis_reset_cmd,
-	"Reset the board using the FPGA sequencer",
+#ifdef CONFIG_SYS_LONGHELP
+static char pixis_help_text[] =
 	"- hard reset to default bank\n"
 	"pixis_reset altbank - reset to alternate bank\n"
 #ifdef DEBUG
 	"pixis_reset dump - display the PIXIS registers\n"
 #endif
-	"pixis_reset sysclk <SYSCLK_freq> - reset with SYSCLK frequency(KHz)\n"
+	"pixis_reset sysclk <SYSCLK_freq> - reset with SYSCLK frequency(KHz)\n";
+#endif
+
+U_BOOT_CMD(
+	pixis_reset, CONFIG_SYS_MAXARGS, 1, pixis_reset_cmd,
+	"Reset the board using the FPGA sequencer", pixis_help_text
 	);
diff --git a/board/freescale/common/qixis.c b/board/freescale/common/qixis.c
index 6cd7e51..c92902a 100644
--- a/board/freescale/common/qixis.c
+++ b/board/freescale/common/qixis.c
@@ -32,22 +32,22 @@ void qixis_write(unsigned int reg, u8 value)
 
 void qixis_reset(void)
 {
-	QIXIS_WRITE(rst_ctl, 0x83);
+	QIXIS_WRITE(rst_ctl, QIXIS_RST_CTL_RESET);
 }
 
 void qixis_bank_reset(void)
 {
-	QIXIS_WRITE(rcfg_ctl, 0x20);
-	QIXIS_WRITE(rcfg_ctl, 0x21);
+	QIXIS_WRITE(rcfg_ctl, QIXIS_RCFG_CTL_RECONFIG_IDLE);
+	QIXIS_WRITE(rcfg_ctl, QIXIS_RCFG_CTL_RECONFIG_START);
 }
 
-/* Set the boot bank to the power-on default bank0 */
+/* Set the boot bank to the power-on default bank */
 void clear_altbank(void)
 {
 	u8 reg;
 
 	reg = QIXIS_READ(brdcfg[0]);
-	reg = reg & ~QIXIS_LBMAP_MASK;
+	reg = (reg & ~QIXIS_LBMAP_MASK) | QIXIS_LBMAP_DFLTBANK;
 	QIXIS_WRITE(brdcfg[0], reg);
 }
 
@@ -85,11 +85,11 @@ static void qixis_dump_regs(void)
 	printf("ctl_sys	= %02x\n", QIXIS_READ(ctl_sys));
 	printf("rcw_ctl = %02x\n", QIXIS_READ(rcw_ctl));
 	printf("present = %02x\n", QIXIS_READ(present));
+	printf("present2 = %02x\n", QIXIS_READ(present2));
 	printf("clk_spd = %02x\n", QIXIS_READ(clk_spd));
 	printf("stat_dut = %02x\n", QIXIS_READ(stat_dut));
 	printf("stat_sys = %02x\n", QIXIS_READ(stat_sys));
 	printf("stat_alrm = %02x\n", QIXIS_READ(stat_alrm));
-	printf("ctl_sys2 = %02x\n", QIXIS_READ(ctl_sys2));
 }
 #endif
 
@@ -115,7 +115,8 @@ int qixis_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 		for (i = 0; i < ARRAY_SIZE(period); i++) {
 			if (strcmp(argv[2], period[i]) == 0) {
 				/* disable watchdog */
-				QIXIS_WRITE(rcfg_ctl, rcfg & ~0x08);
+				QIXIS_WRITE(rcfg_ctl,
+					rcfg & ~QIXIS_RCFG_CTL_WATCHDOG_ENBLE);
 				QIXIS_WRITE(watch, ((i<<2) - 1));
 				QIXIS_WRITE(rcfg_ctl, rcfg);
 				return 0;
diff --git a/board/freescale/common/qixis.h b/board/freescale/common/qixis.h
index 7a0268a..b98b180 100644
--- a/board/freescale/common/qixis.h
+++ b/board/freescale/common/qixis.h
@@ -26,7 +26,7 @@ struct qixis {
 	u8 stat_sys;
 	u8 stat_alrm;
 	u8 present;
-	u8 ctl_sys2;
+	u8 present2;    /* Presence Status Register 2,0x0c */
 	u8 rcw_ctl;
 	u8 ctl_led;
 	u8 i2cblk;
@@ -86,12 +86,6 @@ struct qixis {
 	u8 res15[16];
 };
 
-#define QIXIS_BASE		0xffdf0000
-#define QIXIS_LBMAP_SWITCH	7
-#define QIXIS_LBMAP_MASK	0x0f
-#define QIXIS_LBMAP_SHIFT	0
-#define QIXIS_LBMAP_ALTBANK	0x04
-
 u8 qixis_read(unsigned int reg);
 void qixis_write(unsigned int reg, u8 value);
 
diff --git a/board/freescale/common/vsc3316_3308.c b/board/freescale/common/vsc3316_3308.c
new file mode 100644
index 0000000..7868565
--- /dev/null
+++ b/board/freescale/common/vsc3316_3308.c
@@ -0,0 +1,184 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include "vsc3316_3308.h"
+
+#define REVISION_ID_REG		0x7E
+#define INTERFACE_MODE_REG		0x79
+#define CURRENT_PAGE_REGISTER		0x7F
+#define CONNECTION_CONFIG_PAGE		0x00
+#define INPUT_STATE_REG		0x13
+#define GLOBAL_INPUT_ISE1		0x51
+#define GLOBAL_INPUT_ISE2		0x52
+#define GLOBAL_INPUT_LOS		0x55
+#define GLOBAL_CORE_CNTRL		0x5D
+#define OUTPUT_MODE_PAGE		0x23
+#define CORE_CONTROL_PAGE		0x25
+#define CORE_CONFIG_REG		0x75
+
+int vsc_if_enable(unsigned int vsc_addr)
+{
+	u8 data;
+
+	debug("VSC:Configuring VSC at I2C address 0x%2x"
+			" for 2-wire interface\n", vsc_addr);
+
+	/* enable 2-wire Serial InterFace (I2C) */
+	data = 0x02;
+	return i2c_write(vsc_addr, INTERFACE_MODE_REG, 1, &data, 1);
+}
+
+int vsc3316_config(unsigned int vsc_addr, const int8_t con_arr[][2],
+		unsigned int num_con)
+{
+	unsigned int i;
+	u8 rev_id = 0;
+	int ret;
+
+	debug("VSC:Initializing VSC3316 at I2C address 0x%2x"
+		" for Tx\n", vsc_addr);
+
+	ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1);
+	if (ret < 0) {
+		printf("VSC:0x%x could not read REV_ID from device.\n",
+			vsc_addr);
+		return ret;
+	}
+
+	if (rev_id != 0xab) {
+		printf("VSC: device at address 0x%x is not VSC3316/3308.\n",
+			vsc_addr);
+		return -ENODEV;
+	}
+
+	ret = vsc_if_enable(vsc_addr);
+	if (ret) {
+		printf("VSC:0x%x could not configured for 2-wire I/F.\n",
+			vsc_addr);
+		return ret;
+	}
+
+	/* config connections - page 0x00 */
+	i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE);
+
+	/* Making crosspoint connections, by connecting required
+	 * input to output */
+	for (i = 0; i < num_con ; i++)
+		i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]);
+
+	/* input state - page 0x13 */
+	i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG);
+	/* Configuring the required input of the switch */
+	for (i = 0; i < num_con ; i++)
+		i2c_reg_write(vsc_addr, con_arr[i][0], 0x80);
+
+	/* Setting Global Input LOS threshold value */
+	i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0x60);
+
+	/* config output mode - page 0x23 */
+	i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE);
+	/* Turn ON the Output driver correspond to required output*/
+	for (i = 0; i < num_con ; i++)
+		i2c_reg_write(vsc_addr,  con_arr[i][1], 0);
+
+	/* configure global core control register, Turn on Global core power */
+	i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0);
+
+	vsc_wp_config(vsc_addr);
+
+	return 0;
+}
+
+int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2],
+		unsigned int num_con)
+{
+	unsigned int i;
+	u8 rev_id = 0;
+	int ret;
+
+	debug("VSC:Initializing VSC3308 at I2C address 0x%x"
+		" for Tx\n", vsc_addr);
+
+	ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1);
+	if (ret < 0) {
+		printf("VSC:0x%x could not read REV_ID from device.\n",
+			vsc_addr);
+		return ret;
+	}
+
+	if (rev_id != 0xab) {
+		printf("VSC: device at address 0x%x is not VSC3316/3308.\n",
+			vsc_addr);
+		return -ENODEV;
+	}
+
+	ret = vsc_if_enable(vsc_addr);
+	if (ret) {
+		printf("VSC:0x%x could not configured for 2-wire I/F.\n",
+			vsc_addr);
+		return ret;
+	}
+
+	/* config connections - page 0x00 */
+	i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE);
+
+	/* Making crosspoint connections, by connecting required
+	 * input to output */
+	for (i = 0; i < num_con ; i++)
+		i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]);
+
+	/*Configure Global Input ISE and gain */
+	i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE1, 0x12);
+	i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE2, 0x12);
+
+	/* input state - page 0x13 */
+	i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG);
+	/* Turning ON the required input of the switch */
+	for (i = 0; i < num_con ; i++)
+		i2c_reg_write(vsc_addr, con_arr[i][0], 0);
+
+	/* Setting Global Input LOS threshold value */
+	i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0x60);
+
+	/* config output mode - page 0x23 */
+	i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE);
+	/* Turn ON the Output driver correspond to required output*/
+	for (i = 0; i < num_con ; i++)
+		i2c_reg_write(vsc_addr,  con_arr[i][1], 0);
+
+	/* configure global core control register, Turn on Global core power */
+	i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0);
+
+	vsc_wp_config(vsc_addr);
+
+	return 0;
+}
+
+void vsc_wp_config(unsigned int vsc_addr)
+{
+	debug("VSC:Configuring VSC at address:0x%x for WP\n", vsc_addr);
+
+	/* For new crosspoint configuration to occur, WP bit of
+	 * CORE_CONFIG_REG should be set 1 and then reset to 0 */
+	i2c_reg_write(vsc_addr, CORE_CONFIG_REG, 0x01);
+	i2c_reg_write(vsc_addr, CORE_CONFIG_REG, 0x0);
+}
diff --git a/board/freescale/common/vsc3316_3308.h b/board/freescale/common/vsc3316_3308.h
new file mode 100644
index 0000000..effd66d
--- /dev/null
+++ b/board/freescale/common/vsc3316_3308.h
@@ -0,0 +1,34 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __VSC_CROSSBAR_H_
+#define __VSC_CROSSBAR_H	1_
+
+#include <common.h>
+#include <i2c.h>
+#include <errno.h>
+
+int vsc_if_enable(unsigned int vsc_addr);
+int vsc3316_config(unsigned int vsc_addr, const int8_t con_arr[][2],
+		unsigned int num_con);
+int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2],
+		unsigned int num_con);
+void vsc_wp_config(unsigned int vsc_addr);
+
+#endif	/* __VSC_CROSSBAR_H_ */
diff --git a/board/freescale/m5208evbe/u-boot.lds b/board/freescale/m5208evbe/u-boot.lds
index 6e39be1..2c151f2 100644
--- a/board/freescale/m5208evbe/u-boot.lds
+++ b/board/freescale/m5208evbe/u-boot.lds
@@ -69,9 +69,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m52277evb/u-boot.lds b/board/freescale/m52277evb/u-boot.lds
index 3e9f4c3..dbd6f6a 100644
--- a/board/freescale/m52277evb/u-boot.lds
+++ b/board/freescale/m52277evb/u-boot.lds
@@ -68,9 +68,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5235evb/u-boot.lds b/board/freescale/m5235evb/u-boot.lds
index d39e734..00932ae 100644
--- a/board/freescale/m5235evb/u-boot.lds
+++ b/board/freescale/m5235evb/u-boot.lds
@@ -68,9 +68,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5249evb/u-boot.lds b/board/freescale/m5249evb/u-boot.lds
index c4039ed..d054f20 100644
--- a/board/freescale/m5249evb/u-boot.lds
+++ b/board/freescale/m5249evb/u-boot.lds
@@ -68,9 +68,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5253demo/u-boot.lds b/board/freescale/m5253demo/u-boot.lds
index cbd2831..f8116f6 100644
--- a/board/freescale/m5253demo/u-boot.lds
+++ b/board/freescale/m5253demo/u-boot.lds
@@ -69,9 +69,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5253evbe/u-boot.lds b/board/freescale/m5253evbe/u-boot.lds
index c4039ed..d054f20 100644
--- a/board/freescale/m5253evbe/u-boot.lds
+++ b/board/freescale/m5253evbe/u-boot.lds
@@ -68,9 +68,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5271evb/u-boot.lds b/board/freescale/m5271evb/u-boot.lds
index 4717036..133ec01 100644
--- a/board/freescale/m5271evb/u-boot.lds
+++ b/board/freescale/m5271evb/u-boot.lds
@@ -68,9 +68,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5272c3/u-boot.lds b/board/freescale/m5272c3/u-boot.lds
index c4039ed..d054f20 100644
--- a/board/freescale/m5272c3/u-boot.lds
+++ b/board/freescale/m5272c3/u-boot.lds
@@ -68,9 +68,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5275evb/u-boot.lds b/board/freescale/m5275evb/u-boot.lds
index 6c2dfe8..fc68de1 100644
--- a/board/freescale/m5275evb/u-boot.lds
+++ b/board/freescale/m5275evb/u-boot.lds
@@ -68,9 +68,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5282evb/u-boot.lds b/board/freescale/m5282evb/u-boot.lds
index 4ba1964..ad49874 100644
--- a/board/freescale/m5282evb/u-boot.lds
+++ b/board/freescale/m5282evb/u-boot.lds
@@ -29,6 +29,9 @@ SECTIONS
   {
     arch/m68k/cpu/mcf52x2/start.o	(.text*)
 
+    . = DEFINED(env_offset) ? env_offset : .;
+    common/env_embedded.o      (.text*)
+
     *(.text*)
   }
   _etext = .;
@@ -65,9 +68,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m53017evb/u-boot.lds b/board/freescale/m53017evb/u-boot.lds
index 80935f2..d25a36f 100644
--- a/board/freescale/m53017evb/u-boot.lds
+++ b/board/freescale/m53017evb/u-boot.lds
@@ -71,9 +71,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5329evb/u-boot.lds b/board/freescale/m5329evb/u-boot.lds
index 40af8bc..6616594 100644
--- a/board/freescale/m5329evb/u-boot.lds
+++ b/board/freescale/m5329evb/u-boot.lds
@@ -69,9 +69,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m5373evb/u-boot.lds b/board/freescale/m5373evb/u-boot.lds
index 19342ac..bc40fd6 100644
--- a/board/freescale/m5373evb/u-boot.lds
+++ b/board/freescale/m5373evb/u-boot.lds
@@ -69,9 +69,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m54418twr/Makefile b/board/freescale/m54418twr/Makefile
new file mode 100644
index 0000000..1e53f48
--- /dev/null
+++ b/board/freescale/m54418twr/Makefile
@@ -0,0 +1,43 @@
+# Copyright 2010-2012 Freescale Semiconductor, Inc.
+# TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	= $(BOARD).o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/m54418twr/config.mk b/board/freescale/m54418twr/config.mk
new file mode 100644
index 0000000..a592335
--- /dev/null
+++ b/board/freescale/m54418twr/config.mk
@@ -0,0 +1,25 @@
+# Copyright 2010-2012 Freescale Semiconductor, Inc.
+# TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(CONFIG_SYS_TEXT_BASE)
diff --git a/board/freescale/m54418twr/m54418twr.c b/board/freescale/m54418twr/m54418twr.c
new file mode 100644
index 0000000..6e57bef
--- /dev/null
+++ b/board/freescale/m54418twr/m54418twr.c
@@ -0,0 +1,129 @@
+/*
+ * Copyright 2010-2012 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <spi.h>
+#include <asm/io.h>
+#include <asm/immap.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	/*
+	 * need to to:
+	 * Check serial flash size. if 2mb evb, else 8mb demo
+	 */
+	puts("Board: ");
+	puts("Freescale MCF54418 Tower System\n");
+	return 0;
+};
+
+phys_size_t initdram(int board_type)
+{
+	u32 dramsize;
+
+#if defined(CONFIG_SERIAL_BOOT)
+	/*
+	 * Serial Boot: The dram is already initialized in start.S
+	 * only require to return DRAM size
+	 */
+	dramsize = CONFIG_SYS_SDRAM_SIZE * 0x100000;
+#else
+	sdramc_t *sdram = (sdramc_t *)(MMAP_SDRAM);
+	ccm_t *ccm = (ccm_t *)MMAP_CCM;
+	gpio_t *gpio = (gpio_t *) MMAP_GPIO;
+	pm_t *pm = (pm_t *) MMAP_PM;
+	u32 i;
+
+	dramsize = CONFIG_SYS_SDRAM_SIZE * 0x100000;
+
+	for (i = 0x13; i < 0x20; i++) {
+		if (dramsize == (1 << i))
+			break;
+	}
+
+	out_8(&pm->pmcr0, 0x2E);
+	out_8(&gpio->mscr_sdram, 1);
+
+	clrbits_be16(&ccm->misccr2, CCM_MISCCR2_FBHALF);
+	setbits_be16(&ccm->misccr2, CCM_MISCCR2_DDR2CLK);
+
+	out_be32(&sdram->rcrcr, 0x40000000);
+	out_be32(&sdram->padcr, 0x01030203);
+
+	out_be32(&sdram->cr00, 0x01010101);
+	out_be32(&sdram->cr01, 0x00000101);
+	out_be32(&sdram->cr02, 0x01010100);
+	out_be32(&sdram->cr03, 0x01010000);
+	out_be32(&sdram->cr04, 0x00010101);
+	out_be32(&sdram->cr06, 0x00010100);
+	out_be32(&sdram->cr07, 0x00000001);
+	out_be32(&sdram->cr08, 0x01000001);
+	out_be32(&sdram->cr09, 0x00000100);
+	out_be32(&sdram->cr10, 0x00010001);
+	out_be32(&sdram->cr11, 0x00000200);
+	out_be32(&sdram->cr12, 0x01000002);
+	out_be32(&sdram->cr13, 0x00000000);
+	out_be32(&sdram->cr14, 0x00000100);
+	out_be32(&sdram->cr15, 0x02000100);
+	out_be32(&sdram->cr16, 0x02000407);
+	out_be32(&sdram->cr17, 0x02030007);
+	out_be32(&sdram->cr18, 0x02000100);
+	out_be32(&sdram->cr19, 0x0A030203);
+	out_be32(&sdram->cr20, 0x00020708);
+	out_be32(&sdram->cr21, 0x00050008);
+	out_be32(&sdram->cr22, 0x04030002);
+	out_be32(&sdram->cr23, 0x00000004);
+	out_be32(&sdram->cr24, 0x020A0000);
+	out_be32(&sdram->cr25, 0x0C00000E);
+	out_be32(&sdram->cr26, 0x00002004);
+	out_be32(&sdram->cr28, 0x00100010);
+	out_be32(&sdram->cr29, 0x00100010);
+	out_be32(&sdram->cr31, 0x07990000);
+	out_be32(&sdram->cr40, 0x00000000);
+	out_be32(&sdram->cr41, 0x00C80064);
+	out_be32(&sdram->cr42, 0x44520002);
+	out_be32(&sdram->cr43, 0x00C80023);
+	out_be32(&sdram->cr45, 0x0000C350);
+	out_be32(&sdram->cr56, 0x04000000);
+	out_be32(&sdram->cr57, 0x03000304);
+	out_be32(&sdram->cr58, 0x40040000);
+	out_be32(&sdram->cr59, 0xC0004004);
+	out_be32(&sdram->cr60, 0x0642C000);
+	out_be32(&sdram->cr61, 0x00000642);
+	asm("tpf");
+
+	out_be32(&sdram->cr09, 0x01000100);
+
+	udelay(100);
+#endif
+	return dramsize;
+};
+
+int testdram(void)
+{
+	return 0;
+}
diff --git a/board/freescale/m54418twr/u-boot.lds b/board/freescale/m54418twr/u-boot.lds
new file mode 100644
index 0000000..36a4c26
--- /dev/null
+++ b/board/freescale/m54418twr/u-boot.lds
@@ -0,0 +1,99 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(m68k)
+
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  .text      :
+  {
+    arch/m68k/cpu/mcf5445x/start.o		(.text*)
+
+    *(.text*)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
+  }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+
+  .reloc   :
+  {
+    __got_start = .;
+    KEEP(*(.got))
+    __got_end = .;
+    _GOT2_TABLE_ = .;
+    KEEP(*(.got2))
+    _FIXUP_TABLE_ = .;
+    KEEP(*(.fixup))
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data*)
+    *(.sdata*)
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss  (NOLOAD)     :
+  {
+   _sbss = .;
+   *(.bss*)
+   *(.sbss*)
+   *(COMMON)
+   . = ALIGN(4);
+   _ebss = .;
+  }
+  __bss_end__ = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/freescale/m54451evb/u-boot.lds b/board/freescale/m54451evb/u-boot.lds
index 45924b7..91328a4 100644
--- a/board/freescale/m54451evb/u-boot.lds
+++ b/board/freescale/m54451evb/u-boot.lds
@@ -66,9 +66,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m54455evb/u-boot.lds b/board/freescale/m54455evb/u-boot.lds
index f341449..36a4c26 100644
--- a/board/freescale/m54455evb/u-boot.lds
+++ b/board/freescale/m54455evb/u-boot.lds
@@ -66,9 +66,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m547xevb/u-boot.lds b/board/freescale/m547xevb/u-boot.lds
index 5472689..de4d0eb 100644
--- a/board/freescale/m547xevb/u-boot.lds
+++ b/board/freescale/m547xevb/u-boot.lds
@@ -66,9 +66,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/m548xevb/u-boot.lds b/board/freescale/m548xevb/u-boot.lds
index cf3f38c..fbbe0c5 100644
--- a/board/freescale/m548xevb/u-boot.lds
+++ b/board/freescale/m548xevb/u-boot.lds
@@ -66,9 +66,11 @@ SECTIONS
   PROVIDE (edata = .);
 
   . = .;
-  __u_boot_cmd_start = .;
-  .u_boot_cmd : { *(.u_boot_cmd) }
-  __u_boot_cmd_end = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	#include <u-boot.lst>
+  }
 
   . = .;
   __start___ex_table = .;
diff --git a/board/freescale/mpc8313erdb/mpc8313erdb.c b/board/freescale/mpc8313erdb/mpc8313erdb.c
index 730ec4e..1071803 100644
--- a/board/freescale/mpc8313erdb/mpc8313erdb.c
+++ b/board/freescale/mpc8313erdb/mpc8313erdb.c
@@ -70,22 +70,22 @@ int checkboard(void)
 #ifndef CONFIG_NAND_SPL
 static struct pci_region pci_regions[] = {
 	{
-		bus_start: CONFIG_SYS_PCI1_MEM_BASE,
-		phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
-		size: CONFIG_SYS_PCI1_MEM_SIZE,
-		flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+		.bus_start = CONFIG_SYS_PCI1_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCI1_MEM_PHYS,
+		.size = CONFIG_SYS_PCI1_MEM_SIZE,
+		.flags = PCI_REGION_MEM | PCI_REGION_PREFETCH
 	},
 	{
-		bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
-		phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
-		size: CONFIG_SYS_PCI1_MMIO_SIZE,
-		flags: PCI_REGION_MEM
+		.bus_start = CONFIG_SYS_PCI1_MMIO_BASE,
+		.phys_start = CONFIG_SYS_PCI1_MMIO_PHYS,
+		.size = CONFIG_SYS_PCI1_MMIO_SIZE,
+		.flags = PCI_REGION_MEM
 	},
 	{
-		bus_start: CONFIG_SYS_PCI1_IO_BASE,
-		phys_start: CONFIG_SYS_PCI1_IO_PHYS,
-		size: CONFIG_SYS_PCI1_IO_SIZE,
-		flags: PCI_REGION_IO
+		.bus_start = CONFIG_SYS_PCI1_IO_BASE,
+		.phys_start = CONFIG_SYS_PCI1_IO_PHYS,
+		.size = CONFIG_SYS_PCI1_IO_SIZE,
+		.flags = PCI_REGION_IO
 	}
 };
 
diff --git a/board/freescale/mpc8568mds/bcsr.c b/board/freescale/mpc8568mds/bcsr.c
index 30676e1..2a172cc 100644
--- a/board/freescale/mpc8568mds/bcsr.c
+++ b/board/freescale/mpc8568mds/bcsr.c
@@ -25,7 +25,7 @@
 
 #include "bcsr.h"
 
-void enable_8568mds_duart()
+void enable_8568mds_duart(void)
 {
 	volatile uint* duart_mux	= (uint *)(CONFIG_SYS_CCSRBAR + 0xe0060);
 	volatile uint* devices		= (uint *)(CONFIG_SYS_CCSRBAR + 0xe0070);
@@ -36,21 +36,21 @@ void enable_8568mds_duart()
 	bcsr[5] |= 0x01;		/* Enable Duart in BCSR*/
 }
 
-void enable_8568mds_flash_write()
+void enable_8568mds_flash_write(void)
 {
 	volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
 
 	bcsr[9] |= 0x01;
 }
 
-void disable_8568mds_flash_write()
+void disable_8568mds_flash_write(void)
 {
 	volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
 
 	bcsr[9] &= ~(0x01);
 }
 
-void enable_8568mds_qe_mdio()
+void enable_8568mds_qe_mdio(void)
 {
 	u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
 
diff --git a/board/freescale/mpc8569mds/bcsr.c b/board/freescale/mpc8569mds/bcsr.c
index b688e5c..37d0c5f 100644
--- a/board/freescale/mpc8569mds/bcsr.c
+++ b/board/freescale/mpc8569mds/bcsr.c
@@ -25,17 +25,17 @@
 
 #include "bcsr.h"
 
-void enable_8569mds_flash_write()
+void enable_8569mds_flash_write(void)
 {
 	setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 17), BCSR17_FLASH_nWP);
 }
 
-void disable_8569mds_flash_write()
+void disable_8569mds_flash_write(void)
 {
 	clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 17), BCSR17_FLASH_nWP);
 }
 
-void enable_8569mds_qe_uec()
+void enable_8569mds_qe_uec(void)
 {
 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 	setbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 7),
@@ -60,7 +60,7 @@ void enable_8569mds_qe_uec()
 #endif
 }
 
-void disable_8569mds_brd_eeprom_write_protect()
+void disable_8569mds_brd_eeprom_write_protect(void)
 {
 	clrbits_8((u8 *)(CONFIG_SYS_BCSR_BASE + 7), BCSR7_BRD_WRT_PROTECT);
 }
diff --git a/board/freescale/mx31ads/u-boot.lds b/board/freescale/mx31ads/u-boot.lds
index 91ffdbe..5267729 100644
--- a/board/freescale/mx31ads/u-boot.lds
+++ b/board/freescale/mx31ads/u-boot.lds
@@ -57,9 +57,11 @@ SECTIONS
 	}
 
 	. = ALIGN(4);
-	__u_boot_cmd_start = .;
-	.u_boot_cmd : { *(.u_boot_cmd) }
-	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	.u_boot_list : {
+	#include <u-boot.lst>
+	}
 
 	. = ALIGN(4);
 
diff --git a/board/freescale/t4qds/Makefile b/board/freescale/t4qds/Makefile
new file mode 100644
index 0000000..ff09ffa
--- /dev/null
+++ b/board/freescale/t4qds/Makefile
@@ -0,0 +1,54 @@
+#
+# Copyright 2012 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
+COBJS-$(CONFIG_T4240QDS)+= eth.o
+COBJS-$(CONFIG_PCI)	+= pci.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/t4qds/ddr.c b/board/freescale/t4qds/ddr.c
new file mode 100644
index 0000000..692616a
--- /dev/null
+++ b/board/freescale/t4qds/ddr.c
@@ -0,0 +1,186 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 or later as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct board_specific_parameters {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 clk_adjust;
+	u32 wrlvl_start;
+	u32 wrlvl_ctl_2;
+	u32 wrlvl_ctl_3;
+	u32 cpo;
+	u32 write_data_delay;
+	u32 force_2T;
+};
+
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_parameters udimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
+	 * ranks| mhz|adjst| start |   ctl2    |  ctl3  |      |delay |
+	 */
+	{2,  1350,    5,     7, 0x0809090b, 0x0c0c0d09,   0xff,    2,  0},
+	{2,  1666,    5,     8, 0x080a0a0c, 0x0c0d0e0a,   0xff,    2,  0},
+	{2,  2140,    5,     8, 0x090a0b0c, 0x0e0f100b,   0xff,    2,  0},
+	{1,  1350,    5,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
+	{1,  1700,    5,     8, 0x080a0a0c, 0x0c0d0e0a,   0xff,    2,  0},
+	{1,  1900,    4,     8, 0x080a0a0c, 0x0e0e0f0a,   0xff,    2,  0},
+	{1,  2140,    4,     8, 0x090a0b0c, 0x0e0f100b,   0xff,    2,  0},
+	{}
+};
+
+/*
+ * The three slots have slightly different timing. The center values are good
+ * for all slots. We use identical speed tables for them. In future use, if
+ * DIMMs require separated tables, make more entries as needed.
+ */
+static const struct board_specific_parameters *udimms[] = {
+	udimm0,
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
+	 * ranks| mhz|adjst| start |   ctl2    |  ctl3  |      |delay |
+	 */
+	{4,  1350,    5,     9, 0x08070605, 0x07080805,   0xff,    2,  0},
+	{4,  1666,    5,     8, 0x08070605, 0x07080805,   0xff,    2,  0},
+	{4,  2140,    5,     8, 0x08070605, 0x07081805,   0xff,    2,  0},
+	{2,  1350,    5,     7, 0x0809090b, 0x0c0c0d09,   0xff,    2,  0},
+	{2,  1666,    5,     8, 0x080a0a0c, 0x0c0d0e0a,   0xff,    2,  0},
+	{2,  2140,    5,     8, 0x090a0b0c, 0x0e0f100b,   0xff,    2,  0},
+	{1,  1350,    5,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
+	{1,  1700,    5,     8, 0x080a0a0c, 0x0c0d0e0a,   0xff,    2,  0},
+	{1,  1900,    4,     8, 0x080a0a0c, 0x0e0e0f0a,   0xff,    2,  0},
+	{1,  2140,    4,     8, 0x090a0b0c, 0x0e0f100b,   0xff,    2,  0},
+	{}
+};
+
+/*
+ * The three slots have slightly different timing. See comments above.
+ */
+static const struct board_specific_parameters *rdimms[] = {
+	rdimm0,
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num > 2) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	/*
+	 * we use identical timing for all slots. If needed, change the code
+	 * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
+	 */
+	if (popts->registered_dimm_en)
+		pbsp = rdimms[0];
+	else
+		pbsp = udimms[0];
+
+
+	/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->cpo_override = pbsp->cpo;
+				popts->write_data_delay =
+					pbsp->write_data_delay;
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+				popts->twoT_en = pbsp->force_2T;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found "
+			"for data rate %lu MT/s\n"
+			"Trying to use the highest speed (%u) parameters\n",
+			ddr_freq, pbsp_highest->datarate_mhz_high);
+		popts->cpo_override = pbsp_highest->cpo;
+		popts->write_data_delay = pbsp_highest->write_data_delay;
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+		popts->twoT_en = pbsp_highest->force_2T;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+found:
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	/* DHC_EN =1, ODT = 75 Ohm */
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+	puts("Initializing....using SPD\n");
+
+	dram_size = fsl_ddr_sdram();
+
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
+
+	puts("    DDR: ");
+	return dram_size;
+}
diff --git a/board/freescale/t4qds/eth.c b/board/freescale/t4qds/eth.c
new file mode 100644
index 0000000..a49c7d4
--- /dev/null
+++ b/board/freescale/t4qds/eth.c
@@ -0,0 +1,495 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+#include <asm/fsl_serdes.h>
+#include "../common/qixis.h"
+#include "../common/fman.h"
+
+#include "t4240qds_qixis.h"
+
+#define EMI_NONE	0xFFFFFFFF
+#define EMI1_RGMII	0
+#define EMI1_SLOT1	1
+#define EMI1_SLOT2	2
+#define EMI1_SLOT3	3
+#define EMI1_SLOT4	4
+#define EMI1_SLOT5	5
+#define EMI1_SLOT7	7
+#define EMI2		8 /* tmp, FIXME */
+/* Slot6 and Slot8 do not have EMI connections */
+
+static int mdio_mux[NUM_FM_PORTS];
+
+static const char *mdio_names[] = {
+	"T4240QDS_MDIO0",
+	"T4240QDS_MDIO1",
+	"T4240QDS_MDIO2",
+	"T4240QDS_MDIO3",
+	"T4240QDS_MDIO4",
+	"T4240QDS_MDIO5",
+	"NULL",
+	"T4240QDS_MDIO7",
+	"T4240QDS_10GC",
+};
+
+static u8 lane_to_slot_fsm1[] = {1, 1, 1, 1, 2, 2, 2, 2};
+static u8 lane_to_slot_fsm2[] = {3, 3, 3, 3, 4, 4, 4, 4};
+
+static const char *t4240qds_mdio_name_for_muxval(u8 muxval)
+{
+	return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u8 muxval)
+{
+	struct mii_dev *bus;
+	const char *name = t4240qds_mdio_name_for_muxval(muxval);
+
+	if (!name) {
+		printf("No bus for muxval %x\n", muxval);
+		return NULL;
+	}
+
+	bus = miiphy_get_dev_by_name(name);
+
+	if (!bus) {
+		printf("No bus by name %s\n", name);
+		return NULL;
+	}
+
+	return bus;
+}
+
+struct t4240qds_mdio {
+	u8 muxval;
+	struct mii_dev *realbus;
+};
+
+static void t4240qds_mux_mdio(u8 muxval)
+{
+	u8 brdcfg4;
+	if ((muxval < 6) || (muxval == 7)) {
+		brdcfg4 = QIXIS_READ(brdcfg[4]);
+		brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+		brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
+		QIXIS_WRITE(brdcfg[4], brdcfg4);
+	}
+}
+
+static int t4240qds_mdio_read(struct mii_dev *bus, int addr, int devad,
+				int regnum)
+{
+	struct t4240qds_mdio *priv = bus->priv;
+
+	t4240qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int t4240qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+				int regnum, u16 value)
+{
+	struct t4240qds_mdio *priv = bus->priv;
+
+	t4240qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int t4240qds_mdio_reset(struct mii_dev *bus)
+{
+	struct t4240qds_mdio *priv = bus->priv;
+
+	return priv->realbus->reset(priv->realbus);
+}
+
+static int t4240qds_mdio_init(char *realbusname, u8 muxval)
+{
+	struct t4240qds_mdio *pmdio;
+	struct mii_dev *bus = mdio_alloc();
+
+	if (!bus) {
+		printf("Failed to allocate T4240QDS MDIO bus\n");
+		return -1;
+	}
+
+	pmdio = malloc(sizeof(*pmdio));
+	if (!pmdio) {
+		printf("Failed to allocate T4240QDS private data\n");
+		free(bus);
+		return -1;
+	}
+
+	bus->read = t4240qds_mdio_read;
+	bus->write = t4240qds_mdio_write;
+	bus->reset = t4240qds_mdio_reset;
+	sprintf(bus->name, t4240qds_mdio_name_for_muxval(muxval));
+
+	pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+	if (!pmdio->realbus) {
+		printf("No bus with name %s\n", realbusname);
+		free(bus);
+		free(pmdio);
+		return -1;
+	}
+
+	pmdio->muxval = muxval;
+	bus->priv = pmdio;
+
+	return mdio_register(bus);
+}
+
+void board_ft_fman_fixup_port(void *blob, char * prop, phys_addr_t pa,
+				enum fm_port port, int offset)
+{
+	if (mdio_mux[port] == EMI1_RGMII)
+		fdt_set_phy_handle(blob, prop, pa, "phy_rgmii");
+
+	/* TODO: will do with dts */
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+	/* TODO: will do with dts */
+}
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FMAN_ENET)
+	int i;
+	struct memac_mdio_info dtsec_mdio_info;
+	struct memac_mdio_info tgec_mdio_info;
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 srds_prtcl_s1, srds_prtcl_s2;
+
+	srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
+					FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+	srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+	srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
+					FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+	srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+
+	/* Initialize the mdio_mux array so we can recognize empty elements */
+	for (i = 0; i < NUM_FM_PORTS; i++)
+		mdio_mux[i] = EMI_NONE;
+
+	dtsec_mdio_info.regs =
+		(struct memac_mdio_controller *)CONFIG_SYS_FM2_DTSEC_MDIO_ADDR;
+
+	dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+	/* Register the 1G MDIO bus */
+	fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+	tgec_mdio_info.regs =
+		(struct memac_mdio_controller *)CONFIG_SYS_FM2_TGEC_MDIO_ADDR;
+	tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+	/* Register the 10G MDIO bus */
+	fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+	/* Register the muxing front-ends to the MDIO buses */
+	t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII);
+	t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
+	t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
+	t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
+	t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
+	t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5);
+	t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT7);
+	t4240qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2);
+
+
+	switch (srds_prtcl_s1) {
+	case 1:
+	case 2:
+	case 4:
+		/* XAUI/HiGig in Slot1 and Slot2 */
+		fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_10GEC2, FM1_10GEC2_PHY_ADDR);
+		break;
+	case 28:
+	case 36:
+		/* SGMII in Slot1 and Slot2 */
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+		if ((srds_prtcl_s2 != 56) && (srds_prtcl_s2 != 57)) {
+			fm_info_set_phy_address(FM1_DTSEC9,
+						SGMII_CARD_PORT4_PHY_ADDR);
+			fm_info_set_phy_address(FM1_DTSEC10,
+						SGMII_CARD_PORT3_PHY_ADDR);
+		}
+		break;
+	case 38:
+		fm_info_set_phy_address(FM1_DTSEC5, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC6, QSGMII_CARD_PHY_ADDR);
+		if ((srds_prtcl_s2 != 56) && (srds_prtcl_s2 != 57)) {
+			fm_info_set_phy_address(FM1_DTSEC9,
+						QSGMII_CARD_PHY_ADDR);
+			fm_info_set_phy_address(FM1_DTSEC10,
+						QSGMII_CARD_PHY_ADDR);
+		}
+		break;
+	case 40:
+	case 46:
+	case 48:
+		fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+		if ((srds_prtcl_s2 != 56) && (srds_prtcl_s2 != 57)) {
+			fm_info_set_phy_address(FM1_DTSEC10,
+						SGMII_CARD_PORT3_PHY_ADDR);
+			fm_info_set_phy_address(FM1_DTSEC9,
+						SGMII_CARD_PORT4_PHY_ADDR);
+		}
+		fm_info_set_phy_address(FM1_DTSEC1, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC2, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC4, QSGMII_CARD_PHY_ADDR);
+		break;
+	default:
+		puts("Invalid SerDes1 protocol for T4240QDS\n");
+		break;
+	}
+
+	for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+		int idx = i - FM1_DTSEC1, lane, slot;
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_SGMII:
+			lane = serdes_get_first_lane(FSL_SRDS_1,
+						SGMII_FM1_DTSEC1 + idx);
+			if (lane < 0)
+				break;
+			slot = lane_to_slot_fsm1[lane];
+			debug("FM1@DTSEC%u expects SGMII in slot %u\n",
+				idx + 1, slot);
+			if (QIXIS_READ(present2) & (1 << (slot - 1)))
+				fm_disable_port(i);
+			switch (slot) {
+			case 1:
+				mdio_mux[i] = EMI1_SLOT1;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			case 2:
+				mdio_mux[i] = EMI1_SLOT2;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			};
+			break;
+		case PHY_INTERFACE_MODE_RGMII:
+			/* FM1 DTSEC5 routes to RGMII with EC2 */
+			debug("FM1@DTSEC%u is RGMII at address %u\n",
+				idx + 1, 2);
+			if (i == FM1_DTSEC5)
+				fm_info_set_phy_address(i, 2);
+			mdio_mux[i] = EMI1_RGMII;
+			fm_info_set_mdio(i,
+				mii_dev_for_muxval(mdio_mux[i]));
+			break;
+		default:
+			break;
+		}
+	}
+
+	for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_XGMII:
+			mdio_mux[i] = EMI2;
+			fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+			break;
+		default:
+			break;
+		}
+	}
+
+
+#if (CONFIG_SYS_NUM_FMAN == 2)
+	switch (srds_prtcl_s2) {
+	case 1:
+	case 2:
+	case 4:
+		/* XAUI/HiGig in Slot3 and Slot4 */
+		fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC1_PHY_ADDR);
+		fm_info_set_phy_address(FM2_10GEC2, FM2_10GEC2_PHY_ADDR);
+		break;
+	case 7:
+	case 13:
+	case 14:
+	case 16:
+	case 22:
+	case 23:
+	case 25:
+	case 26:
+		/* XAUI/HiGig in Slot3, SGMII in Slot4 */
+		fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC1_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR);
+		break;
+	case 28:
+	case 36:
+		/* SGMII in Slot3 and Slot4 */
+		fm_info_set_phy_address(FM2_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC5, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC9, SGMII_CARD_PORT4_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC10, SGMII_CARD_PORT3_PHY_ADDR);
+		break;
+	case 38:
+		/* QSGMII in Slot3 and Slot4 */
+		fm_info_set_phy_address(FM2_DTSEC1, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC2, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC3, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC4, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC5, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC6, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC9, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC10, QSGMII_CARD_PHY_ADDR);
+		break;
+	case 40:
+	case 46:
+	case 48:
+		/* SGMII in Slot3 */
+		fm_info_set_phy_address(FM2_DTSEC5, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC9, SGMII_CARD_PORT4_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC10, SGMII_CARD_PORT3_PHY_ADDR);
+		/* QSGMII in Slot4 */
+		fm_info_set_phy_address(FM2_DTSEC1, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC2, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC3, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC4, QSGMII_CARD_PHY_ADDR);
+		break;
+	case 50:
+	case 52:
+	case 54:
+		fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC1_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC1, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC2, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC3, QSGMII_CARD_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC4, QSGMII_CARD_PHY_ADDR);
+		break;
+	case 56:
+	case 57:
+		/* XFI in Slot3, SGMII in Slot4 */
+		fm_info_set_phy_address(FM1_10GEC1, XFI_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_10GEC2, XFI_CARD_PORT2_PHY_ADDR);
+		fm_info_set_phy_address(FM2_10GEC2, XFI_CARD_PORT3_PHY_ADDR);
+		fm_info_set_phy_address(FM2_10GEC1, XFI_CARD_PORT4_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR);
+		break;
+	default:
+		puts("Invalid SerDes2 protocol for T4240QDS\n");
+		break;
+	}
+
+	for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
+		int idx = i - FM2_DTSEC1, lane, slot;
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_SGMII:
+			lane = serdes_get_first_lane(FSL_SRDS_2,
+						SGMII_FM2_DTSEC1 + idx);
+			if (lane < 0)
+				break;
+			slot = lane_to_slot_fsm2[lane];
+			debug("FM2@DTSEC%u expects SGMII in slot %u\n",
+				idx + 1, slot);
+			if (QIXIS_READ(present2) & (1 << (slot - 1)))
+				fm_disable_port(i);
+			switch (slot) {
+			case 3:
+				mdio_mux[i] = EMI1_SLOT3;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			case 4:
+				mdio_mux[i] = EMI1_SLOT4;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			};
+			break;
+		case PHY_INTERFACE_MODE_RGMII:
+			/*
+			 * If DTSEC5 is RGMII, then it's routed via via EC1 to
+			 * the first on-board RGMII port.  If DTSEC6 is RGMII,
+			 * then it's routed via via EC2 to the second on-board
+			 * RGMII port.
+			 */
+			debug("FM2@DTSEC%u is RGMII at address %u\n",
+				idx + 1, i == FM2_DTSEC5 ? 1 : 2);
+			fm_info_set_phy_address(i, i == FM2_DTSEC5 ? 1 : 2);
+			mdio_mux[i] = EMI1_RGMII;
+			fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+			break;
+		default:
+			break;
+		}
+	}
+
+	for (i = FM2_10GEC1; i < FM2_10GEC1 + CONFIG_SYS_NUM_FM2_10GEC; i++) {
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_XGMII:
+			mdio_mux[i] = EMI2;
+			fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+			break;
+		default:
+			break;
+		}
+	}
+#endif /* CONFIG_SYS_NUM_FMAN */
+
+	cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+	return pci_eth_init(bis);
+}
diff --git a/board/freescale/t4qds/law.c b/board/freescale/t4qds/law.c
new file mode 100644
index 0000000..5debcf6
--- /dev/null
+++ b/board/freescale/t4qds/law.c
@@ -0,0 +1,47 @@
+/*
+ * Copyright 2008-2012 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+	SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t4qds/pci.c b/board/freescale/t4qds/pci.c
new file mode 100644
index 0000000..fc00b4a
--- /dev/null
+++ b/board/freescale/t4qds/pci.c
@@ -0,0 +1,39 @@
+/*
+ * Copyright 2007-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+	FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t4qds/t4240qds_qixis.h b/board/freescale/t4qds/t4240qds_qixis.h
new file mode 100644
index 0000000..efb718d
--- /dev/null
+++ b/board/freescale/t4qds/t4240qds_qixis.h
@@ -0,0 +1,56 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __T4020QDS_QIXIS_H__
+#define __T4020QDS_QIXIS_H__
+
+/* Definitions of QIXIS Registers for T4020QDS */
+
+/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
+#define BRDCFG4_EMISEL_MASK		0xE0
+#define BRDCFG4_EMISEL_SHIFT		5
+
+/* SYSCLK */
+#define QIXIS_SYSCLK_66			0x0
+#define QIXIS_SYSCLK_83			0x1
+#define QIXIS_SYSCLK_100		0x2
+#define QIXIS_SYSCLK_125		0x3
+#define QIXIS_SYSCLK_133		0x4
+#define QIXIS_SYSCLK_150		0x5
+#define QIXIS_SYSCLK_160		0x6
+#define QIXIS_SYSCLK_166		0x7
+
+/* DDRCLK */
+#define QIXIS_DDRCLK_66			0x0
+#define QIXIS_DDRCLK_100		0x1
+#define QIXIS_DDRCLK_125		0x2
+#define QIXIS_DDRCLK_133		0x3
+
+#define BRDCFG5_RESET			0x00
+
+#define BRDCFG12_SD3EN_MASK		0x20
+#define BRDCFG12_SD3MX_MASK		0x08
+#define BRDCFG12_SD3MX_SLOT5		0x08
+#define BRDCFG12_SD3MX_SLOT6		0x00
+#define BRDCFG12_SD4EN_MASK		0x04
+#define BRDCFG12_SD4MX_MASK		0x03
+#define BRDCFG12_SD4MX_SLOT7		0x02
+#define BRDCFG12_SD4MX_SLOT8		0x01
+#define BRDCFG12_SD4MX_AURO_SATA	0x00
+#endif
diff --git a/board/freescale/t4qds/t4qds.c b/board/freescale/t4qds/t4qds.c
new file mode 100644
index 0000000..88b8ced
--- /dev/null
+++ b/board/freescale/t4qds/t4qds.c
@@ -0,0 +1,395 @@
+/*
+ * Copyright 2009-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "../common/qixis.h"
+#include "../common/vsc3316_3308.h"
+#include "t4qds.h"
+#include "t4240qds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	u8 sw;
+	struct cpu_type *cpu = gd->cpu;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+	unsigned int i;
+
+	printf("Board: %sQDS, ", cpu->name);
+	printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
+		QIXIS_READ(id), QIXIS_READ(arch), QIXIS_READ(scver));
+
+	sw = QIXIS_READ(brdcfg[0]);
+	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+	if (sw < 0x8)
+		printf("vBank: %d\n", sw);
+	else if (sw == 0x8)
+		puts("Promjet\n");
+	else if (sw == 0x9)
+		puts("NAND\n");
+	else
+		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+
+	/* Display the RCW, so that no one gets confused as to what RCW
+	 * we're actually using for this boot.
+	 */
+	puts("Reset Configuration Word (RCW):");
+	for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
+		u32 rcw = in_be32(&gur->rcwsr[i]);
+
+		if ((i % 4) == 0)
+			printf("\n       %08x:", i * 4);
+		printf(" %08x", rcw);
+	}
+	puts("\n");
+
+	/*
+	 * Display the actual SERDES reference clocks as configured by the
+	 * dip switches on the board.  Note that the SWx registers could
+	 * technically be set to force the reference clocks to match the
+	 * values that the SERDES expects (or vice versa).  For now, however,
+	 * we just display both values and hope the user notices when they
+	 * don't match.
+	 */
+	puts("SERDES Reference Clocks: ");
+	sw = QIXIS_READ(brdcfg[2]);
+	for (i = 0; i < MAX_SERDES; i++) {
+		static const char *freq[] = {
+			"100", "125", "156.25", "161.1328125"};
+		unsigned int clock = (sw >> (2 * i)) & 3;
+
+		printf("SERDES%u=%sMHz ", i+1, freq[clock]);
+	}
+	puts("\n");
+
+	return 0;
+}
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+	int ret;
+
+	ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+	if (ret) {
+		puts("PCA: failed to select proper channel\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/* Configure Crossbar switches for Front-Side SerDes Ports */
+int config_frontside_crossbar_vsc3316(void)
+{
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 srds_prtcl_s1, srds_prtcl_s2;
+	int ret;
+
+	ret = select_i2c_ch_pca9547(I2C_MUX_CH_VSC3316_FS);
+	if (ret)
+		return ret;
+
+	srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
+			FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+	srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+	if (srds_prtcl_s1) {
+		ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm1_tx, 8);
+		if (ret)
+			return ret;
+		ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm1_rx, 8);
+		if (ret)
+			return ret;
+	}
+
+	srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
+				FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+	srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+	if (srds_prtcl_s2) {
+		ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm2_tx, 8);
+		if (ret)
+			return ret;
+		ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm2_rx, 8);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+int config_backside_crossbar_mux(void)
+{
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 srds_prtcl_s3, srds_prtcl_s4;
+	u8 brdcfg;
+
+	srds_prtcl_s3 = in_be32(&gur->rcwsr[4]) &
+			FSL_CORENET2_RCWSR4_SRDS3_PRTCL;
+	srds_prtcl_s3 >>= FSL_CORENET2_RCWSR4_SRDS3_PRTCL_SHIFT;
+	switch (srds_prtcl_s3) {
+	case 0:
+		/* SerDes3 is not enabled */
+		break;
+	case 2:
+	case 9:
+	case 10:
+		/* SD3(0:7) => SLOT5(0:7) */
+		brdcfg = QIXIS_READ(brdcfg[12]);
+		brdcfg &= ~BRDCFG12_SD3MX_MASK;
+		brdcfg |= BRDCFG12_SD3MX_SLOT5;
+		QIXIS_WRITE(brdcfg[12], brdcfg);
+		break;
+	case 4:
+	case 6:
+	case 8:
+	case 12:
+	case 14:
+	case 16:
+	case 17:
+	case 19:
+	case 20:
+		/* SD3(4:7) => SLOT6(0:3) */
+		brdcfg = QIXIS_READ(brdcfg[12]);
+		brdcfg &= ~BRDCFG12_SD3MX_MASK;
+		brdcfg |= BRDCFG12_SD3MX_SLOT6;
+		QIXIS_WRITE(brdcfg[12], brdcfg);
+		break;
+	default:
+		printf("WARNING: unsupported for SerDes3 Protocol %d\n",
+				srds_prtcl_s3);
+		return -1;
+	}
+
+	srds_prtcl_s4 = in_be32(&gur->rcwsr[4]) &
+			FSL_CORENET2_RCWSR4_SRDS4_PRTCL;
+	srds_prtcl_s4 >>= FSL_CORENET2_RCWSR4_SRDS4_PRTCL_SHIFT;
+	switch (srds_prtcl_s4) {
+	case 0:
+		/* SerDes4 is not enabled */
+		break;
+	case 2:
+		/* 10b, SD4(0:7) => SLOT7(0:7) */
+		brdcfg = QIXIS_READ(brdcfg[12]);
+		brdcfg &= ~BRDCFG12_SD4MX_MASK;
+		brdcfg |= BRDCFG12_SD4MX_SLOT7;
+		QIXIS_WRITE(brdcfg[12], brdcfg);
+		break;
+	case 4:
+	case 6:
+	case 8:
+		/* x1b, SD4(4:7) => SLOT8(0:3) */
+		brdcfg = QIXIS_READ(brdcfg[12]);
+		brdcfg &= ~BRDCFG12_SD4MX_MASK;
+		brdcfg |= BRDCFG12_SD4MX_SLOT8;
+		QIXIS_WRITE(brdcfg[12], brdcfg);
+		break;
+	case 10:
+	case 12:
+	case 14:
+	case 16:
+	case 18:
+		/* 00b, SD4(4:5) => AURORA, SD4(6:7) => SATA */
+		brdcfg = QIXIS_READ(brdcfg[12]);
+		brdcfg &= ~BRDCFG12_SD4MX_MASK;
+		brdcfg |= BRDCFG12_SD4MX_AURO_SATA;
+		QIXIS_WRITE(brdcfg[12], brdcfg);
+		break;
+	default:
+		printf("WARNING: unsupported for SerDes4 Protocol %d\n",
+				srds_prtcl_s4);
+		return -1;
+	}
+
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash + PROMJET region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash + promjet */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+	set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+	setup_portals();
+#endif
+
+	/* Disable remote I2C connectoin */
+	QIXIS_WRITE(brdcfg[5], BRDCFG5_RESET);
+
+	/* Configure board SERDES ports crossbar */
+	config_frontside_crossbar_vsc3316();
+	config_backside_crossbar_mux();
+	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+
+	return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch (sysclk_conf & 0x0F) {
+	case QIXIS_SYSCLK_83:
+		return 83333333;
+	case QIXIS_SYSCLK_100:
+		return 100000000;
+	case QIXIS_SYSCLK_125:
+		return 125000000;
+	case QIXIS_SYSCLK_133:
+		return 133333333;
+	case QIXIS_SYSCLK_150:
+		return 150000000;
+	case QIXIS_SYSCLK_160:
+		return 160000000;
+	case QIXIS_SYSCLK_166:
+		return 166666666;
+	}
+	return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch ((ddrclk_conf & 0x30) >> 4) {
+	case QIXIS_DDRCLK_100:
+		return 100000000;
+	case QIXIS_DDRCLK_125:
+		return 125000000;
+	case QIXIS_DDRCLK_133:
+		return 133333333;
+	}
+	return 66666666;
+}
+
+static const char *serdes_clock_to_string(u32 clock)
+{
+	switch (clock) {
+	case SRDS_PLLCR0_RFCK_SEL_100:
+		return "100";
+	case SRDS_PLLCR0_RFCK_SEL_125:
+		return "125";
+	case SRDS_PLLCR0_RFCK_SEL_156_25:
+		return "156.25";
+	case SRDS_PLLCR0_RFCK_SEL_161_13:
+		return "161.1328125";
+	default:
+		return "???";
+	}
+}
+
+int misc_init_r(void)
+{
+	u8 sw;
+	serdes_corenet_t *srds_regs =
+		(void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+	u32 actual[MAX_SERDES];
+	unsigned int i;
+
+	sw = QIXIS_READ(brdcfg[2]);
+	for (i = 0; i < MAX_SERDES; i++) {
+		unsigned int clock = (sw >> (2 * i)) & 3;
+		switch (clock) {
+		case 0:
+			actual[i] = SRDS_PLLCR0_RFCK_SEL_100;
+			break;
+		case 1:
+			actual[i] = SRDS_PLLCR0_RFCK_SEL_125;
+			break;
+		case 2:
+			actual[i] = SRDS_PLLCR0_RFCK_SEL_156_25;
+			break;
+		case 3:
+			actual[i] = SRDS_PLLCR0_RFCK_SEL_161_13;
+			break;
+		}
+	}
+
+	for (i = 0; i < MAX_SERDES; i++) {
+		u32 pllcr0 = srds_regs->bank[i].pllcr0;
+		u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK;
+		if (expected != actual[i]) {
+			printf("Warning: SERDES%u expects reference clock"
+			       " %sMHz, but actual is %sMHz\n", i + 1,
+			       serdes_clock_to_string(expected),
+			       serdes_clock_to_string(actual[i]));
+		}
+	}
+
+	return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+	pci_of_setup(blob, bd);
+#endif
+
+	fdt_fixup_liodn(blob);
+	fdt_fixup_dr_usb(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+	fdt_fixup_fman_ethernet(blob);
+	fdt_fixup_board_enet(blob);
+#endif
+}
diff --git a/board/freescale/t4qds/t4qds.h b/board/freescale/t4qds/t4qds.h
new file mode 100644
index 0000000..c6a3492
--- /dev/null
+++ b/board/freescale/t4qds/t4qds.h
@@ -0,0 +1,37 @@
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CORENET_DS_H__
+#define __CORENET_DS_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+static const int8_t vsc3316_fsm1_tx[8][2] = { {0, 0}, {1, 1}, {6, 6}, {7, 7},
+				{8, 8}, {9, 9}, {14, 14}, {15, 15} };
+
+static const int8_t vsc3316_fsm2_tx[8][2] = { {2, 2}, {3, 3}, {4, 4}, {5, 5},
+				{10, 10}, {11, 11}, {12, 12}, {13, 13} };
+
+static const int8_t vsc3316_fsm1_rx[8][2] = { {2, 12}, {3, 13}, {4, 5}, {5, 4},
+				{10, 11}, {11, 10}, {12, 2}, {13, 3} };
+
+static const int8_t vsc3316_fsm2_rx[8][2] = { {0, 15}, {1, 14}, {6, 7}, {7, 6},
+				{8, 9}, {9, 8}, {14, 1}, {15, 0} };
+#endif
diff --git a/board/freescale/t4qds/tlb.c b/board/freescale/t4qds/tlb.c
new file mode 100644
index 0000000..078a6e4
--- /dev/null
+++ b/board/freescale/t4qds/tlb.c
@@ -0,0 +1,136 @@
+/*
+ * Copyright 2008-2012 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+	/*
+	 * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
+	 * SRAM is at 0xfff00000, it covered the 0xfffff000.
+	 */
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 0, BOOKE_PAGESZ_1M, 1),
+#else
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_16M, 1),
+
+	/* *I*G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000,
+		      CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_256M, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000,
+		      CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 5, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 6, BOOKE_PAGESZ_256K, 1),
+
+	/* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 9, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 10, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 11, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 12, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 13, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+	/*
+	 * *I*G - NAND
+	 * entry 14 and 15 has been used hard coded, they will be disabled
+	 * in cpu_init_f, so we use entry 16 for nand.
+	 */
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 16, BOOKE_PAGESZ_1M, 1),
+#endif
+	SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 17, BOOKE_PAGESZ_4K, 1),
+
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);