diff options
author | Shengzhou Liu <Shengzhou.Liu@freescale.com> | 2014-11-24 17:11:56 +0800 |
---|---|---|
committer | York Sun <yorksun@freescale.com> | 2014-12-05 08:06:15 -0800 |
commit | 48c6f328f00d245fb92f330ff94b213e8a375621 (patch) | |
tree | 44d288d0bc4e8207da4c8654f01ce2d9e8d0be76 /board/freescale | |
parent | aba800481879e3674b55c95d63bcbd8aff1cb204 (diff) | |
download | u-boot-imx-48c6f328f00d245fb92f330ff94b213e8a375621.zip u-boot-imx-48c6f328f00d245fb92f330ff94b213e8a375621.tar.gz u-boot-imx-48c6f328f00d245fb92f330ff94b213e8a375621.tar.bz2 |
powerpc/t1024rdb: Add T1024 RDB board support
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
Diffstat (limited to 'board/freescale')
-rw-r--r-- | board/freescale/t102xrdb/Kconfig | 12 | ||||
-rw-r--r-- | board/freescale/t102xrdb/MAINTAINERS | 10 | ||||
-rw-r--r-- | board/freescale/t102xrdb/Makefile | 17 | ||||
-rw-r--r-- | board/freescale/t102xrdb/README | 258 | ||||
-rw-r--r-- | board/freescale/t102xrdb/cpld.c | 103 | ||||
-rw-r--r-- | board/freescale/t102xrdb/cpld.h | 45 | ||||
-rw-r--r-- | board/freescale/t102xrdb/ddr.c | 154 | ||||
-rw-r--r-- | board/freescale/t102xrdb/eth_t102xrdb.c | 100 | ||||
-rw-r--r-- | board/freescale/t102xrdb/law.c | 32 | ||||
-rw-r--r-- | board/freescale/t102xrdb/pci.c | 23 | ||||
-rw-r--r-- | board/freescale/t102xrdb/spl.c | 107 | ||||
-rw-r--r-- | board/freescale/t102xrdb/t1024_pbi.cfg | 26 | ||||
-rw-r--r-- | board/freescale/t102xrdb/t1024_rcw.cfg | 8 | ||||
-rw-r--r-- | board/freescale/t102xrdb/t102xrdb.c | 144 | ||||
-rw-r--r-- | board/freescale/t102xrdb/t102xrdb.h | 13 | ||||
-rw-r--r-- | board/freescale/t102xrdb/tlb.c | 117 |
16 files changed, 1169 insertions, 0 deletions
diff --git a/board/freescale/t102xrdb/Kconfig b/board/freescale/t102xrdb/Kconfig new file mode 100644 index 0000000..10d49f5 --- /dev/null +++ b/board/freescale/t102xrdb/Kconfig @@ -0,0 +1,12 @@ +if TARGET_T102XRDB + +config SYS_BOARD + default "t102xrdb" + +config SYS_VENDOR + default "freescale" + +config SYS_CONFIG_NAME + default "T102xRDB" + +endif diff --git a/board/freescale/t102xrdb/MAINTAINERS b/board/freescale/t102xrdb/MAINTAINERS new file mode 100644 index 0000000..dc554d4 --- /dev/null +++ b/board/freescale/t102xrdb/MAINTAINERS @@ -0,0 +1,10 @@ +T102XRDB BOARD +M: Shengzhou Liu <Shengzhou.Liu@freescale.com> +S: Maintained +F: board/freescale/t102xrdb/ +F: include/configs/T102xRDB.h +F: configs/T1024RDB_defconfig +F: configs/T1024RDB_NAND_defconfig +F: configs/T1024RDB_SDCARD_defconfig +F: configs/T1024RDB_SPIFLASH_defconfig +F: configs/T1024RDB_SECURE_BOOT_defconfig diff --git a/board/freescale/t102xrdb/Makefile b/board/freescale/t102xrdb/Makefile new file mode 100644 index 0000000..a0cf8f6 --- /dev/null +++ b/board/freescale/t102xrdb/Makefile @@ -0,0 +1,17 @@ +# +# Copyright 2014 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +else +obj-y += t102xrdb.o +obj-y += cpld.o +obj-y += eth_t102xrdb.o +obj-$(CONFIG_PCI) += pci.o +endif +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README new file mode 100644 index 0000000..2b17f50 --- /dev/null +++ b/board/freescale/t102xrdb/README @@ -0,0 +1,258 @@ +T1024 SoC Overview +------------------ +The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor +combines two or one 64-bit Power Architecture e5500 core respectively with high +performance datapath acceleration logic, and network peripheral bus interfaces +required for networking and telecommunications. This processor can be used in +applications such as enterprise WLAN access points, routers, switches, firewall +and other packet processing intensive small enterprise and branch office appliances, +and general-purpose embedded computing. Its high level of integration offers +significant performance benefits and greatly helps to simplify board design. + + +The T1024 SoC includes the following function and features: +- two e5500 cores, each with a private 256 KB L2 cache + - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant) + - Three levels of instructions: User, supervisor, and hypervisor + - Independent boot and reset + - Secure boot capability +- 256 KB shared L3 CoreNet platform cache (CPC) +- Interconnect CoreNet platform + - CoreNet coherency manager supporting coherent and noncoherent transactions + with prioritization and bandwidth allocation amongst CoreNet endpoints + - 150 Gbps coherent read bandwidth +- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support +- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: + - Packet parsing, classification, and distribution + - Queue management for scheduling, packet sequencing, and congestion management + - Cryptography Acceleration (SEC 5.x) + - IEEE 1588 support + - Hardware buffer management for buffer allocation and deallocation + - MACSEC on DPAA-based Ethernet ports +- Ethernet interfaces + - Four 1 Gbps Ethernet controllers +- Parallel Ethernet interfaces + - Two RGMII interfaces +- High speed peripheral interfaces + - Three PCI Express 2.0 controllers/ports running at up to 5 GHz + - One SATA controller supporting 1.5 and 3.0 Gb/s operation + - One QSGMII interface + - Four SGMII interface supporting 1000 Mbps + - Three SGMII interfaces supporting up to 2500 Mbps + - 10GbE XFI or 10Base-KR interface +- Additional peripheral interfaces + - Two USB 2.0 controllers with integrated PHY + - SD/eSDHC/eMMC + - eSPI controller + - Four I2C controllers + - Four UARTs + - Four GPIO controllers + - Integrated flash controller (IFC) + - LCD interface (DIU) with 12 bit dual data rate +- Multicore programmable interrupt controller (PIC) +- Two 8-channel DMA engines +- Single source clocking implementation +- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) +- QUICC Engine block + - 32-bit RISC controller for flexible support of the communications peripherals + - Serial DMA channel for receive and transmit on all serial channels + - Two universal communication controllers, supporting TDM, HDLC, and UART + +T1023 Personality +------------------ +T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and +unavailable deep sleep. Rest of the blocks are almost same as T1024. +Differences between T1024 and T1023 +Feature T1024 T1023 +QUICC Engine: yes no +DIU: yes no +Deep Sleep: yes no +I2C controller: 4 3 +DDR: 64-bit 32-bit +IFC: 32-bit 28-bit + + +T1024RDB board Overview +----------------------- + - Ethernet + - Two on-board 10M/100M/1G bps RGMII ethernet ports + - One on-board 10G bps Base-T port. + - DDR Memory + - Supports 64-bit 4GB DDR3L DIMM + - PCIe + - One on-board PCIe slot. + - Two on-board PCIe Mini-PCIe connectors. + - IFC/Local Bus + - NOR: 128MB 16-bit NOR Flash + - NAND: 1GB 8-bit NAND flash + - CPLD: for system controlling with programable header on-board + - USB + - Supports two USB 2.0 ports with integrated PHYs + - Two type A ports with 5V@1.5A per port. + - SDHC + - one SD connector supporting 1.8V/3.3V via J53. + - SPI + - On-board 64MB SPI flash + - Other + - Two Serial ports + - Four I2C ports + + +Memory map on T1024RDB +---------------------- +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB +0x0_0000_0000 0x0_ffff_ffff DDR 4GB + + +128MB NOR Flash memory Map +-------------------------- +Start Address End Address Definition Max size +0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB +0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB +0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB +0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB +0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB +0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB +0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB +0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB +0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB +0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + +T1024 Clock frequency +--------------------- +BIN Core DDR Platform FMan +Bin1: 1400MHz 1600MT/s 400MHz 700MHz +Bin2: 1200MHz 1600MT/s 400MHz 600MHz +Bin3: 1000MHz 1600MT/s 400MHz 500MHz + + +Software configurations and board settings +------------------------------------------ +1. NOR boot: + a. build NOR boot image + $ make T1024RDB_defconfig + $ make + b. program u-boot.bin image to NOR flash + => tftp 1000000 u-boot.bin + => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize + set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot + + Switching between default bank0 and alternate bank4 on NOR flash + To change boot source to vbank4: + via software: run command 'cpld reset altbank' in u-boot. + via DIP-switch: set SW3[5:7] = '100' + + To change boot source to vbank0: + via software: run command 'cpld reset' in u-boot. + via DIP-Switch: set SW3[5:7] = '000' + +2. NAND Boot: + a. build PBL image for NAND boot + $ make T1024RDB_NAND_defconfig + $ make + b. program u-boot-with-spl-pbl.bin to NAND flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => nand erase 0 $filesize + => nand write 1000000 0 $filesize + set SW1[1:8] = '10001000', SW2[1] = '1', SW3[4] = '1' for NAND boot + +3. SPI Boot: + a. build PBL image for SPI boot + $ make T1024RDB_SPIFLASH_defconfig + $ make + b. program u-boot-with-spl-pbl.bin to SPI flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => sf probe 0 + => sf erase 0 f0000 + => sf write 1000000 0 $filesize + set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot + +4. SD Boot: + a. build PBL image for SD boot + $ make T1024RDB_SDCARD_defconfig + $ make + b. program u-boot-with-spl-pbl.bin to SD/MMC card + => tftp 1000000 u-boot-with-spl-pbl.bin + => mmc write 1000000 8 0x800 + => tftp 1000000 fsl_fman_ucode_t1024_xx.bin + => mmc write 1000000 0x820 80 + set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot + + +2-stage NAND/SPI/SD boot loader +------------------------------- +PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM. +SPL further initializes DDR using SPD and environment variables +and copy u-boot(768 KB) from NAND/SPI/SD device to DDR. +Finally SPL transers control to u-boot for futher booting. + +SPL has following features: + - Executes within 256K + - No relocation required + +Run time view of SPL framework +------------------------------------------------- +|Area | Address | +------------------------------------------------- +|SecureBoot header | 0xFFFC0000 (32KB) | +------------------------------------------------- +|GD, BD | 0xFFFC8000 (4KB) | +------------------------------------------------- +|ENV | 0xFFFC9000 (8KB) | +------------------------------------------------- +|HEAP | 0xFFFCB000 (30KB) | +------------------------------------------------- +|STACK | 0xFFFD8000 (22KB) | +------------------------------------------------- +|U-boot SPL | 0xFFFD8000 (160KB) | +------------------------------------------------- + +NAND Flash memory Map on T1024RDB +------------------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot 1MB(2 block) +0x100000 0x17FFFF u-boot env 512KB(1 block) +0x180000 0x1FFFFF FMAN Ucode 512KB(1 block) +0x200000 0x27FFFF QE Firmware 512KB(1 block) + + +SD Card memory Map on T1024RDB +---------------------------------------------------- +Block #blocks Definition Size +0x008 2048 u-boot img 1MB +0x800 0016 u-boot env 8KB +0x820 0256 FMAN Ucode 128KB +0x920 0256 QE Firmware 128KB + + +SPI Flash memory Map on T1024RDB +---------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot img 1MB +0x100000 0x101FFF u-boot env 8KB +0x110000 0x12FFFF FMAN Ucode 128KB +0x130000 0x14FFFF QE Firmware 128KB + + +For more details, please refer to T1024RDB Reference Manual and access +website www.freescale.com and Freescale QorIQ SDK Infocenter document. diff --git a/board/freescale/t102xrdb/cpld.c b/board/freescale/t102xrdb/cpld.c new file mode 100644 index 0000000..c03894a --- /dev/null +++ b/board/freescale/t102xrdb/cpld.c @@ -0,0 +1,103 @@ +/** + * Copyright 2014 Freescale Semiconductor + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Freescale T1024RDB board-specific CPLD controlling supports. + * + * The following macros need to be defined: + */ + +#include <common.h> +#include <command.h> +#include <asm/io.h> +#include "cpld.h" + +u8 cpld_read(unsigned int reg) +{ + void *p = (void *)CONFIG_SYS_CPLD_BASE; + + return in_8(p + reg); +} + +void cpld_write(unsigned int reg, u8 value) +{ + void *p = (void *)CONFIG_SYS_CPLD_BASE; + + out_8(p + reg, value); +} + +/** + * Set the boot bank to the alternate bank + */ +void cpld_set_altbank(void) +{ + u8 reg = CPLD_READ(flash_csr); + + reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK; + + CPLD_WRITE(flash_csr, reg); + CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET); +} + +/** + * Set the boot bank to the default bank + */ +void cpld_set_defbank(void) +{ + u8 reg = CPLD_READ(flash_csr); + + reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK; + + CPLD_WRITE(flash_csr, reg); + CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET); +} + +static void cpld_dump_regs(void) +{ + printf("cpld_ver = 0x%02x\n", CPLD_READ(cpld_ver)); + printf("cpld_ver_sub = 0x%02x\n", CPLD_READ(cpld_ver_sub)); + printf("hw_ver = 0x%02x\n", CPLD_READ(hw_ver)); + printf("sw_ver = 0x%02x\n", CPLD_READ(sw_ver)); + printf("reset_ctl1 = 0x%02x\n", CPLD_READ(reset_ctl1)); + printf("reset_ctl2 = 0x%02x\n", CPLD_READ(reset_ctl2)); + printf("int_status = 0x%02x\n", CPLD_READ(int_status)); + printf("flash_csr = 0x%02x\n", CPLD_READ(flash_csr)); + printf("fan_ctl_status = 0x%02x\n", CPLD_READ(fan_ctl_status)); + printf("led_ctl_status = 0x%02x\n", CPLD_READ(led_ctl_status)); + printf("sfp_ctl_status = 0x%02x\n", CPLD_READ(sfp_ctl_status)); + printf("misc_ctl_status = 0x%02x\n", CPLD_READ(misc_ctl_status)); + printf("boot_override = 0x%02x\n", CPLD_READ(boot_override)); + printf("boot_config1 = 0x%02x\n", CPLD_READ(boot_config1)); + printf("boot_config2 = 0x%02x\n", CPLD_READ(boot_config2)); + putc('\n'); +} + +int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int rc = 0; + + if (argc <= 1) + return cmd_usage(cmdtp); + + if (strcmp(argv[1], "reset") == 0) { + if (strcmp(argv[2], "altbank") == 0) + cpld_set_altbank(); + else + cpld_set_defbank(); + } else if (strcmp(argv[1], "dump") == 0) { + cpld_dump_regs(); + } else { + rc = cmd_usage(cmdtp); + } + + return rc; +} + +U_BOOT_CMD( + cpld, CONFIG_SYS_MAXARGS, 1, do_cpld, + "Reset the board or alternate bank", + "reset - hard reset to default bank\n" + "cpld reset altbank - reset to alternate bank\n" + "cpld dump - display the CPLD registers\n" + ); diff --git a/board/freescale/t102xrdb/cpld.h b/board/freescale/t102xrdb/cpld.h new file mode 100644 index 0000000..5a3100f --- /dev/null +++ b/board/freescale/t102xrdb/cpld.h @@ -0,0 +1,45 @@ +/** + * Copyright 2014 Freescale Semiconductor + * + * SPDX-License-Identifier: GPL-2.0+ + * + */ + +struct cpld_data { + u8 cpld_ver; /* 0x00 - CPLD Major Revision Register */ + u8 cpld_ver_sub; /* 0x01 - CPLD Minor Revision Register */ + u8 hw_ver; /* 0x02 - Hardware Revision Register */ + u8 sw_ver; /* 0x03 - Software Revision register */ + u8 res0[12]; /* 0x04 - 0x0F - not used */ + u8 reset_ctl1; /* 0x10 - Reset control Register1 */ + u8 reset_ctl2; /* 0x11 - Reset control Register2 */ + u8 int_status; /* 0x12 - Interrupt status Register */ + u8 flash_csr; /* 0x13 - Flash control and status register */ + u8 fan_ctl_status; /* 0x14 - Fan control and status register */ + u8 led_ctl_status; /* 0x15 - LED control and status register */ + u8 sfp_ctl_status; /* 0x16 - SFP control and status register */ + u8 misc_ctl_status; /* 0x17 - Miscellanies ctrl & status register*/ + u8 boot_override; /* 0x18 - Boot override register */ + u8 boot_config1; /* 0x19 - Boot config override register*/ + u8 boot_config2; /* 0x1A - Boot config override register*/ +} cpld_data_t; + + +/* Pointer to the CPLD register set */ + +u8 cpld_read(unsigned int reg); +void cpld_write(unsigned int reg, u8 value); + +#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg)) +#define CPLD_WRITE(reg, value)\ + cpld_write(offsetof(struct cpld_data, reg), value) + +/* CPLD on IFC */ +#define CPLD_LBMAP_MASK 0x3F +#define CPLD_BANK_SEL_MASK 0x07 +#define CPLD_BANK_OVERRIDE 0x40 +#define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */ +#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK 0 */ +#define CPLD_LBMAP_RESET 0xFF +#define CPLD_LBMAP_SHIFT 0x03 +#define CPLD_BOOT_SEL 0x80 diff --git a/board/freescale/t102xrdb/ddr.c b/board/freescale/t102xrdb/ddr.c new file mode 100644 index 0000000..a20330b --- /dev/null +++ b/board/freescale/t102xrdb/ddr.c @@ -0,0 +1,154 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> +#include <asm/fsl_law.h> + +DECLARE_GLOBAL_DATA_PTR; + +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; +}; + +/* + * datarate_mhz_high values need to be in ascending order + */ +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | + */ + {2, 833, 0, 4, 6, 0x06060607, 0x08080807,}, + {2, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,}, + {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,}, + {1, 833, 0, 4, 6, 0x06060607, 0x08080807,}, + {1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,}, + {1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,}, + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + struct cpu_type *cpu = gd->arch.cpu; + + if (ctrl_num > 1) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + /* Get clk_adjust according to the board ddr freqency and n_banks + * specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks && + (pdimm->rank_density >> 30) >= pbsp->rank_gb) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found\n"); + printf("for data rate %lu MT/s\n", ddr_freq); + printf("Trying to use the highest speed (%u) parameters\n", + pbsp_highest->datarate_mhz_high); + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb); + debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ", + pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2); + debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3); + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * rtt and rtt_wr override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_OFF); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_OFF); + + /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit, + * force DDR bus width to 32bit for T1023 + */ + if (cpu->soc_ver == SVR_T1023) + popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; + +#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32 + /* for DDR bus 32bit test on T1024 */ + popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; +#endif +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + +#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; +#else + /* DDR has been initialised by first stage boot loader */ + dram_size = fsl_ddr_sdram_size(); +#endif + return dram_size; +} diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c new file mode 100644 index 0000000..2e400c4 --- /dev/null +++ b/board/freescale/t102xrdb/eth_t102xrdb.c @@ -0,0 +1,100 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <netdev.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <malloc.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <miiphy.h> +#include <phy.h> +#include <asm/fsl_dtsec.h> +#include <asm/fsl_serdes.h> + +int board_eth_init(bd_t *bis) +{ +#if defined(CONFIG_FMAN_ENET) + int i, interface; + struct memac_mdio_info dtsec_mdio_info; + struct memac_mdio_info tgec_mdio_info; + struct mii_dev *dev; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_s1; + + srds_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + + dtsec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; + + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the 1G MDIO bus */ + fm_memac_mdio_init(bis, &dtsec_mdio_info); + + tgec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; + tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; + + /* Register the 10G MDIO bus */ + fm_memac_mdio_init(bis, &tgec_mdio_info); + + /* Set the two on-board RGMII PHY address */ + fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR); + + switch (srds_s1) { + case 0x95: + /* 10G XFI with Aquantia PHY */ + fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR); + break; + default: + printf("SerDes protocol 0x%x is not supported on T102xRDB\n", + srds_s1); + break; + } + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + interface = fm_info_get_enet_if(i); + switch (interface) { + case PHY_INTERFACE_MODE_RGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } + + for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_XGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } + + cpu_eth_init(bis); +#endif /* CONFIG_FMAN_ENET */ + + return pci_eth_init(bis); +} + +void fdt_fixup_board_enet(void *fdt) +{ +} diff --git a/board/freescale/t102xrdb/law.c b/board/freescale/t102xrdb/law.c new file mode 100644 index 0000000..1c9235f --- /dev/null +++ b/board/freescale/t102xrdb/law.c @@ -0,0 +1,32 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { +#ifndef CONFIG_SYS_NO_FLASH + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif +#ifdef CONFIG_SYS_CPLD_BASE_PHYS + SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t102xrdb/pci.c b/board/freescale/t102xrdb/pci.c new file mode 100644 index 0000000..ba7041a --- /dev/null +++ b/board/freescale/t102xrdb/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2007-2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t102xrdb/spl.c b/board/freescale/t102xrdb/spl.c new file mode 100644 index 0000000..dd2dec4 --- /dev/null +++ b/board/freescale/t102xrdb/spl.c @@ -0,0 +1,107 @@ +/* Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <malloc.h> +#include <ns16550.h> +#include <nand.h> +#include <i2c.h> +#include <mmc.h> +#include <fsl_esdhc.h> +#include <spi_flash.h> + +DECLARE_GLOBAL_DATA_PTR; + +phys_size_t get_effective_memsize(void) +{ + return CONFIG_SYS_L3_SIZE; +} + +unsigned long get_board_sys_clk(void) +{ + return CONFIG_SYS_CLK_FREQ; +} + +unsigned long get_board_ddr_clk(void) +{ + return CONFIG_DDR_CLK_FREQ; +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio, sys_clk, ccb_clk; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */ + memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t)); + + /* Update GD pointer */ + gd = (gd_t *)(CONFIG_SPL_GD_ADDR); + + console_init_f(); + + /* initialize selected port with appropriate baud rate */ + sys_clk = get_board_sys_clk(); + plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f; + ccb_clk = sys_clk * plat_ratio / 2; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + ccb_clk / 16 / CONFIG_BAUDRATE); + +#if defined(CONFIG_SPL_MMC_BOOT) + puts("\nSD boot...\n"); +#elif defined(CONFIG_SPL_SPI_BOOT) + puts("\nSPI boot...\n"); +#elif defined(CONFIG_SPL_NAND_BOOT) + puts("\nNAND boot...\n"); +#endif + + relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + bd_t *bd; + + bd = (bd_t *)(gd + sizeof(gd_t)); + memset(bd, 0, sizeof(bd_t)); + gd->bd = bd; + bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR; + bd->bi_memsize = CONFIG_SYS_L3_SIZE; + + probecpu(); + get_clocks(); + mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, + CONFIG_SPL_RELOC_MALLOC_SIZE); + +#ifdef CONFIG_SPL_NAND_BOOT + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_MMC_BOOT + mmc_initialize(bd); + mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif +#ifdef CONFIG_SPL_SPI_BOOT + spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); +#endif + + gd->env_addr = (ulong)(CONFIG_ENV_ADDR); + gd->env_valid = 1; + + i2c_init_all(); + + gd->ram_size = initdram(0); + +#ifdef CONFIG_SPL_MMC_BOOT + mmc_boot(); +#elif defined(CONFIG_SPL_SPI_BOOT) + spi_boot(); +#elif defined(CONFIG_SPL_NAND_BOOT) + nand_boot(); +#endif +} diff --git a/board/freescale/t102xrdb/t1024_pbi.cfg b/board/freescale/t102xrdb/t1024_pbi.cfg new file mode 100644 index 0000000..7b9e9b0 --- /dev/null +++ b/board/freescale/t102xrdb/t1024_pbi.cfg @@ -0,0 +1,26 @@ +#PBI commands +#Initialize CPC1 +09010000 00200400 +09138000 00000000 +091380c0 00000100 +#Configure CPC1 as 256KB SRAM +09010100 00000000 +09010104 fffc0007 +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000cd0 00000000 +09000cd4 fffc0000 +09000cd8 81000011 +#Configure alternate space +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Configure SPI controller +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +091380c0 000FFFFF diff --git a/board/freescale/t102xrdb/t1024_rcw.cfg b/board/freescale/t102xrdb/t1024_rcw.cfg new file mode 100644 index 0000000..cd6f906 --- /dev/null +++ b/board/freescale/t102xrdb/t1024_rcw.cfg @@ -0,0 +1,8 @@ +#PBL preamble and RCW header for T1024RDB +aa55aa55 010e0100 +#SerDes Protocol: 0x95 +#Core/DDR: 1400Mhz/1600MT/s with single source clock +0810000c 00000000 00000000 00000000 +4a800003 80000012 ec027000 21000000 +00000000 00000000 00000000 00030810 +00000000 0b005a08 00000000 00000006 diff --git a/board/freescale/t102xrdb/t102xrdb.c b/board/freescale/t102xrdb/t102xrdb.c new file mode 100644 index 0000000..f5c438d --- /dev/null +++ b/board/freescale/t102xrdb/t102xrdb.c @@ -0,0 +1,144 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <asm/mpc85xx_gpio.h> +#include <fm_eth.h> +#include "t102xrdb.h" +#include "cpld.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + struct cpu_type *cpu = gd->arch.cpu; + static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"}; + + printf("Board: %sRDB, ", cpu->name); + printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ", + CPLD_READ(hw_ver), CPLD_READ(sw_ver)); + +#ifdef CONFIG_SDCARD + puts("SD/MMC\n"); +#elif CONFIG_SPIFLASH + puts("SPI\n"); +#else + u8 reg; + + reg = CPLD_READ(flash_csr); + + if (reg & CPLD_BOOT_SEL) { + puts("NAND\n"); + } else { + reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT); + printf("NOR vBank%d\n", reg); + } +#endif + + puts("SERDES Reference Clocks:\n"); + printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]); + + return 0; +} + +int board_early_init_r(void) +{ +#ifdef CONFIG_SYS_FLASH_BASE + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + int flash_esel = find_tlb_idx((void *)flashbase, 1); + /* + * Remap Boot flash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + if (flash_esel == -1) { + /* very unlikely unless something is messed up */ + puts("Error: Could not find TLB for FLASH BASE\n"); + flash_esel = 2; /* give our best effort to continue */ + } else { + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + } + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); +#endif + + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + return CONFIG_SYS_CLK_FREQ; +} + +unsigned long get_board_ddr_clk(void) +{ + return CONFIG_DDR_CLK_FREQ; +} + +int misc_init_r(void) +{ + return 0; +} + +int ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + fdt_fixup_dr_usb(blob, bd); + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif + + return 0; +} + +#ifdef CONFIG_DEEP_SLEEP +void board_mem_sleep_setup(void) +{ + /* does not provide HW signals for power management */ + CPLD_WRITE(misc_ctl_status, (CPLD_READ(misc_ctl_status) & ~0x40)); + /* Disable MCKE isolation */ + gpio_set_value(2, 0); + udelay(1); +} +#endif diff --git a/board/freescale/t102xrdb/t102xrdb.h b/board/freescale/t102xrdb/t102xrdb.h new file mode 100644 index 0000000..2f23579 --- /dev/null +++ b/board/freescale/t102xrdb/t102xrdb.h @@ -0,0 +1,13 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T1024_RDB_H__ +#define __T1024_RDB_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/freescale/t102xrdb/tlb.c b/board/freescale/t102xrdb/tlb.c new file mode 100644 index 0000000..8269b3d --- /dev/null +++ b/board/freescale/t102xrdb/tlb.c @@ -0,0 +1,117 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the + * SRAM is at 0xfffc0000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256K, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + +#ifndef CONFIG_SPL_BUILD + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 5, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 7, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_16M, 1), +#endif +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 9, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_64K, 1), +#endif +#ifdef CONFIG_SYS_CPLD_BASE + SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_256K, 1), +#endif + +#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD) + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 12, BOOKE_PAGESZ_1G, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, + CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 13, BOOKE_PAGESZ_1G, 1) +#endif + /* entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so if needed more, will use entry 16 later. + */ +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); |