Merge branch 'master' of git://git.denx.de/u-boot-arm

5 files changed, 42 insertions, 91 deletions

diff --git a/board/freescale/mx28evk/iomux.c b/board/freescale/mx28evk/iomux.c
index 16a6d8a..ae6eda3 100644
--- a/board/freescale/mx28evk/iomux.c
+++ b/board/freescale/mx28evk/iomux.c
@@ -173,7 +173,7 @@ const iomux_cfg_t iomux_setup[] = {
 #define HW_DRAM_CTL29_CONFIG	(CS_MAP << 24 | COLUMN_SIZE << 16 | \
 					ADDR_PINS << 8 | APREBIT)
 
-void mx28_adjust_memory_params(uint32_t *dram_vals)
+void mxs_adjust_memory_params(uint32_t *dram_vals)
 {
 	dram_vals[HW_DRAM_CTL29] = HW_DRAM_CTL29_CONFIG;
 }
diff --git a/board/freescale/mx28evk/mx28evk.c b/board/freescale/mx28evk/mx28evk.c
index 867d3c8..d782aea 100644
--- a/board/freescale/mx28evk/mx28evk.c
+++ b/board/freescale/mx28evk/mx28evk.c
@@ -49,8 +49,8 @@ int board_early_init_f(void)
 
 	/* SSP0 clock at 96MHz */
 	mx28_set_sspclk(MXC_SSPCLK0, 96000, 0);
-	/* SSP2 clock at 96MHz */
-	mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
+	/* SSP2 clock at 160MHz */
+	mx28_set_sspclk(MXC_SSPCLK2, 160000, 0);
 
 #ifdef	CONFIG_CMD_USB
 	mxs_iomux_setup_pad(MX28_PAD_SSP2_SS1__USB1_OVERCURRENT);
diff --git a/board/freescale/mx35pdk/README b/board/freescale/mx35pdk/README
index 3d69ed5..7232b53 100644
--- a/board/freescale/mx35pdk/README
+++ b/board/freescale/mx35pdk/README
@@ -71,91 +71,17 @@ exec -c "noinitrd console=ttymxc0,115200 root=/dev/nfsroot rootfstype=nfsroot nf
 Flashing U-Boot
 --------------------------------
 
-There are two options: the original bootloader in NAND can be replaced with
-u-boot, or u-boot can be stored on the NOR flash without erasing
-the delivered bootloader.
+U-boot should be stored on the NOR flash.
+
 The boot storage can be select using the switches on the personality board
 (SW1-SW2) and on the DEBUG board (SW4-SW10).
 
-The second option is to be preferred if you have not a JTAG debugger.
 If something goes wrong flashing the bootloader, it is always possible to
 recover the board booting from the other device.
 
-Replacing the bootloader on the NAND
---------------------------------------
-To replace RedBoot with U-Boot, the easy way is to do this in linux.
-Start the kernel with the suggested options. Make sure to have set the
-mtdparts exactly as described, because this matches the layout on the
-mx35pdk.
-
-You should see in your boot log the following entries for the NAND
-flash:
-
-5 cmdlinepart partitions found on MTD device mxc_nand
-Creating 5 MTD partitions on "mxc_nand":
-0x000000000000-0x000000100000 : "boot"
-0x000000100000-0x000000600000 : "linux"
-0x000000600000-0x000006600000 : "root"
-0x000006600000-0x000006e00000 : "cfg"
-0x000006e00000-0x000080000000 : "user"
-
-You can use the utilities flash_eraseall and nandwrite to put
-u-boot on the NAND. The bootloader is marked as "boot", and 1MB is
-reserved. If everything is correct, this partition is accessed as
-/dev/mtd4. However, check if it is correct with "cat /proc/mtd" and
-get the device node from the partition name:
-
-$ cat /proc/mtd | grep boot
-
-I suggest you try the utilities on a different partition to be sure
-if everything works correctly. If not, and you remove RedBoot, you have to
-reinstall it using the ATK tool as suggested by Freescale, or using a
-JTAG debugger.
-
-I report the versions of the utilities I used (they are provided with ELDK):
-
--bash-3.2# nandwrite --version
-nandwrite $Revision: 1.32 $
-
-flash_eraseall --version
-flash_eraseall $Revision: 1.22 $
-
-nandwrite reports a warning if the file to be saved is not sector aligned.
-This should have no consequences, but I preferred to pad u-boot.bin
-to get no problem at all.
-$ dd if=/dev/zero of=zeros bs=1 count=74800
-$ cat u-boot.bin zeros > u-boot-padded.bin
-
-To erase the partition:
-$ flash_eraseall /dev/mtd4
-
-Writing u-boot:
-
-$ nandwrite /dev/mtd4 u-boot-padded.bin
-
-Now U-Boot is stored on the booting partition.
-
-To boot from NAND, you have to select the switches as follows:
-
-Personality board
-	SW2	1, 4, 5 on
-		2, 3, 6, 7, 8 off
-	SW1	all off
-
-Debug Board:
-	SW5	0
-	SW6	0
-	SW7	0
-	SW8	1
-	SW9	1
-	SW10	0
-
-
 Saving U-Boot in the NOR flash
 ---------------------------------
 
-The procedure to save in the NOR flash is quite the same as to write into the NAND.
-
 Check the partition for boot in the NOR flash. Setting the mtdparts as reported,
 the boot partition should be /dev/mtd0.
 
diff --git a/board/freescale/mx35pdk/mx35pdk.c b/board/freescale/mx35pdk/mx35pdk.c
index 787c923..7cb6b30 100644
--- a/board/freescale/mx35pdk/mx35pdk.c
+++ b/board/freescale/mx35pdk/mx35pdk.c
@@ -32,6 +32,8 @@
 #include <i2c.h>
 #include <pmic.h>
 #include <fsl_pmic.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
 #include <mc9sdz60.h>
 #include <mc13892.h>
 #include <linux/types.h>
@@ -275,3 +277,26 @@ int board_eth_init(bd_t *bis)
 
 	return rc;
 }
+
+#if defined(CONFIG_FSL_ESDHC)
+
+struct fsl_esdhc_cfg esdhc_cfg = {MMC_SDHC1_BASE_ADDR};
+
+int board_mmc_init(bd_t *bis)
+{
+	/* configure pins for SDHC1 only */
+	mxc_request_iomux(MX35_PIN_SD1_CMD, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_SD1_CLK, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_SD1_DATA0, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_SD1_DATA1, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_SD1_DATA2, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_SD1_DATA3, MUX_CONFIG_FUNC);
+
+	return fsl_esdhc_initialize(bis, &esdhc_cfg);
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	return !(mc9sdz60_reg_read(MC9SDZ60_REG_DES_FLAG) & 0x4);
+}
+#endif
diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
index 909ccca..4b4e89b 100644
--- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
+++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
@@ -197,18 +197,18 @@ static iomux_v3_cfg_t button_pads[] = {
 
 static void setup_iomux_enet(void)
 {
-	gpio_direction_output(87, 0);  /* GPIO 3-23 */
-	gpio_direction_output(190, 1); /* GPIO 6-30 */
-	gpio_direction_output(185, 1); /* GPIO 6-25 */
-	gpio_direction_output(187, 1); /* GPIO 6-27 */
-	gpio_direction_output(188, 1); /* GPIO 6-28*/
-	gpio_direction_output(189, 1); /* GPIO 6-29 */
+	gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
+	gpio_direction_output(IMX_GPIO_NR(6, 30), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 25), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
 	imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
-	gpio_direction_output(184, 1); /* GPIO 6-24 */
+	gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
 
 	/* Need delay 10ms according to KSZ9021 spec */
 	udelay(1000 * 10);
-	gpio_set_value(87, 1);  /* GPIO 3-23 */
+	gpio_set_value(IMX_GPIO_NR(3, 23), 1);
 
 	imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
 }
@@ -249,11 +249,11 @@ int board_mmc_getcd(struct mmc *mmc)
        int ret;
 
        if (cfg->esdhc_base == USDHC3_BASE_ADDR) {
-	       gpio_direction_input(192); /*GPIO7_0*/
-	       ret = !gpio_get_value(192);
+		gpio_direction_input(IMX_GPIO_NR(7, 0));
+		ret = !gpio_get_value(IMX_GPIO_NR(7, 0));
        } else {
-	       gpio_direction_input(38); /*GPIO2_6*/
-	       ret = !gpio_get_value(38);
+		gpio_direction_input(IMX_GPIO_NR(2, 6));
+		ret = !gpio_get_value(IMX_GPIO_NR(2, 6));
        }
 
        return ret;