powerpc/85xx: Add T4240RDB board support

T4240RDB board Specification
----------------------------
Memory subsystem:
   6GB DDR3
   128MB NOR flash
   2GB NAND flash

Ethernet:
   Eight 1G SGMII ports
   Four 10Gbps SFP+ ports

PCIe:
   Two PCIe slots

USB:
   Two USB2.0 Type A ports

SDHC:
   One SD-card port

SATA:
   One SATA port

UART:
   Dual RJ45 ports

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]

1 files changed, 118 insertions, 0 deletions

diff --git a/board/freescale/t4rdb/ddr.c b/board/freescale/t4rdb/ddr.c
new file mode 100644
index 0000000..5a43c1b
--- /dev/null
+++ b/board/freescale/t4rdb/ddr.c
@@ -0,0 +1,118 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num > 2) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	/*
+	 * we use identical timing for all slots. If needed, change the code
+	 * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
+	 */
+	if (popts->registered_dimm_en)
+		pbsp = rdimms[0];
+	else
+		pbsp = udimms[0];
+
+
+	/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks &&
+		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found for data\n"
+			"rate %lu MT/s\n"
+			"Trying to use the highest speed (%u) parameters\n",
+			ddr_freq, pbsp_highest->datarate_mhz_high);
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+found:
+	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+		"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x,\n"
+		"wrlvl_ctrl_3 0x%x\n",
+		pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+		pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+		pbsp->wrlvl_ctl_3);
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	/* DHC_EN =1, ODT = 75 Ohm */
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+	puts("Initializing....using SPD\n");
+
+	dram_size = fsl_ddr_sdram();
+
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
+
+	puts("    DDR: ");
+	return dram_size;
+}