summaryrefslogtreecommitdiff
path: root/board/freescale/t102xrdb
diff options
context:
space:
mode:
authorShengzhou Liu <Shengzhou.Liu@freescale.com>2014-11-24 17:11:56 +0800
committerYork Sun <yorksun@freescale.com>2014-12-05 08:06:15 -0800
commit48c6f328f00d245fb92f330ff94b213e8a375621 (patch)
tree44d288d0bc4e8207da4c8654f01ce2d9e8d0be76 /board/freescale/t102xrdb
parentaba800481879e3674b55c95d63bcbd8aff1cb204 (diff)
downloadu-boot-imx-48c6f328f00d245fb92f330ff94b213e8a375621.zip
u-boot-imx-48c6f328f00d245fb92f330ff94b213e8a375621.tar.gz
u-boot-imx-48c6f328f00d245fb92f330ff94b213e8a375621.tar.bz2
powerpc/t1024rdb: Add T1024 RDB board support
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC. T1024RDB board Overview ----------------------- - T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support - Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC - Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - one 10Gbps XFI interface - PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors. - SerDes: 4 lanes up to 10.3125GHz - IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD - eSPI: 64MB N25Q512 SPI flash. - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) - USB: Two Type-A USB2.0 ports with internal PHY - eSDHC: Support SD, SDHC, SDXC and MMC/eMMC - I2C: Four I2C controllers - UART: Two UART serial ports Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT Fix Kconfig by adding SUPPORT_SPL] Reviewed-by: York Sun <yorksun@freescale.com>
Diffstat (limited to 'board/freescale/t102xrdb')
-rw-r--r--board/freescale/t102xrdb/Kconfig12
-rw-r--r--board/freescale/t102xrdb/MAINTAINERS10
-rw-r--r--board/freescale/t102xrdb/Makefile17
-rw-r--r--board/freescale/t102xrdb/README258
-rw-r--r--board/freescale/t102xrdb/cpld.c103
-rw-r--r--board/freescale/t102xrdb/cpld.h45
-rw-r--r--board/freescale/t102xrdb/ddr.c154
-rw-r--r--board/freescale/t102xrdb/eth_t102xrdb.c100
-rw-r--r--board/freescale/t102xrdb/law.c32
-rw-r--r--board/freescale/t102xrdb/pci.c23
-rw-r--r--board/freescale/t102xrdb/spl.c107
-rw-r--r--board/freescale/t102xrdb/t1024_pbi.cfg26
-rw-r--r--board/freescale/t102xrdb/t1024_rcw.cfg8
-rw-r--r--board/freescale/t102xrdb/t102xrdb.c144
-rw-r--r--board/freescale/t102xrdb/t102xrdb.h13
-rw-r--r--board/freescale/t102xrdb/tlb.c117
16 files changed, 1169 insertions, 0 deletions
diff --git a/board/freescale/t102xrdb/Kconfig b/board/freescale/t102xrdb/Kconfig
new file mode 100644
index 0000000..10d49f5
--- /dev/null
+++ b/board/freescale/t102xrdb/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_T102XRDB
+
+config SYS_BOARD
+ default "t102xrdb"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_CONFIG_NAME
+ default "T102xRDB"
+
+endif
diff --git a/board/freescale/t102xrdb/MAINTAINERS b/board/freescale/t102xrdb/MAINTAINERS
new file mode 100644
index 0000000..dc554d4
--- /dev/null
+++ b/board/freescale/t102xrdb/MAINTAINERS
@@ -0,0 +1,10 @@
+T102XRDB BOARD
+M: Shengzhou Liu <Shengzhou.Liu@freescale.com>
+S: Maintained
+F: board/freescale/t102xrdb/
+F: include/configs/T102xRDB.h
+F: configs/T1024RDB_defconfig
+F: configs/T1024RDB_NAND_defconfig
+F: configs/T1024RDB_SDCARD_defconfig
+F: configs/T1024RDB_SPIFLASH_defconfig
+F: configs/T1024RDB_SECURE_BOOT_defconfig
diff --git a/board/freescale/t102xrdb/Makefile b/board/freescale/t102xrdb/Makefile
new file mode 100644
index 0000000..a0cf8f6
--- /dev/null
+++ b/board/freescale/t102xrdb/Makefile
@@ -0,0 +1,17 @@
+#
+# Copyright 2014 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
+obj-y += t102xrdb.o
+obj-y += cpld.o
+obj-y += eth_t102xrdb.o
+obj-$(CONFIG_PCI) += pci.o
+endif
+obj-y += ddr.o
+obj-y += law.o
+obj-y += tlb.o
diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README
new file mode 100644
index 0000000..2b17f50
--- /dev/null
+++ b/board/freescale/t102xrdb/README
@@ -0,0 +1,258 @@
+T1024 SoC Overview
+------------------
+The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor
+combines two or one 64-bit Power Architecture e5500 core respectively with high
+performance datapath acceleration logic, and network peripheral bus interfaces
+required for networking and telecommunications. This processor can be used in
+applications such as enterprise WLAN access points, routers, switches, firewall
+and other packet processing intensive small enterprise and branch office appliances,
+and general-purpose embedded computing. Its high level of integration offers
+significant performance benefits and greatly helps to simplify board design.
+
+
+The T1024 SoC includes the following function and features:
+- two e5500 cores, each with a private 256 KB L2 cache
+ - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant)
+ - Three levels of instructions: User, supervisor, and hypervisor
+ - Independent boot and reset
+ - Secure boot capability
+- 256 KB shared L3 CoreNet platform cache (CPC)
+- Interconnect CoreNet platform
+ - CoreNet coherency manager supporting coherent and noncoherent transactions
+ with prioritization and bandwidth allocation amongst CoreNet endpoints
+ - 150 Gbps coherent read bandwidth
+- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
+- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions:
+ - Packet parsing, classification, and distribution
+ - Queue management for scheduling, packet sequencing, and congestion management
+ - Cryptography Acceleration (SEC 5.x)
+ - IEEE 1588 support
+ - Hardware buffer management for buffer allocation and deallocation
+ - MACSEC on DPAA-based Ethernet ports
+- Ethernet interfaces
+ - Four 1 Gbps Ethernet controllers
+- Parallel Ethernet interfaces
+ - Two RGMII interfaces
+- High speed peripheral interfaces
+ - Three PCI Express 2.0 controllers/ports running at up to 5 GHz
+ - One SATA controller supporting 1.5 and 3.0 Gb/s operation
+ - One QSGMII interface
+ - Four SGMII interface supporting 1000 Mbps
+ - Three SGMII interfaces supporting up to 2500 Mbps
+ - 10GbE XFI or 10Base-KR interface
+- Additional peripheral interfaces
+ - Two USB 2.0 controllers with integrated PHY
+ - SD/eSDHC/eMMC
+ - eSPI controller
+ - Four I2C controllers
+ - Four UARTs
+ - Four GPIO controllers
+ - Integrated flash controller (IFC)
+ - LCD interface (DIU) with 12 bit dual data rate
+- Multicore programmable interrupt controller (PIC)
+- Two 8-channel DMA engines
+- Single source clocking implementation
+- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
+- QUICC Engine block
+ - 32-bit RISC controller for flexible support of the communications peripherals
+ - Serial DMA channel for receive and transmit on all serial channels
+ - Two universal communication controllers, supporting TDM, HDLC, and UART
+
+T1023 Personality
+------------------
+T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and
+unavailable deep sleep. Rest of the blocks are almost same as T1024.
+Differences between T1024 and T1023
+Feature T1024 T1023
+QUICC Engine: yes no
+DIU: yes no
+Deep Sleep: yes no
+I2C controller: 4 3
+DDR: 64-bit 32-bit
+IFC: 32-bit 28-bit
+
+
+T1024RDB board Overview
+-----------------------
+ - Ethernet
+ - Two on-board 10M/100M/1G bps RGMII ethernet ports
+ - One on-board 10G bps Base-T port.
+ - DDR Memory
+ - Supports 64-bit 4GB DDR3L DIMM
+ - PCIe
+ - One on-board PCIe slot.
+ - Two on-board PCIe Mini-PCIe connectors.
+ - IFC/Local Bus
+ - NOR: 128MB 16-bit NOR Flash
+ - NAND: 1GB 8-bit NAND flash
+ - CPLD: for system controlling with programable header on-board
+ - USB
+ - Supports two USB 2.0 ports with integrated PHYs
+ - Two type A ports with 5V@1.5A per port.
+ - SDHC
+ - one SD connector supporting 1.8V/3.3V via J53.
+ - SPI
+ - On-board 64MB SPI flash
+ - Other
+ - Two Serial ports
+ - Four I2C ports
+
+
+Memory map on T1024RDB
+----------------------
+Start Address End Address Description Size
+0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB
+0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
+0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
+0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
+0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
+0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
+0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
+0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
+0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
+0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
+0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB
+0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB
+0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB
+0x0_0000_0000 0x0_ffff_ffff DDR 4GB
+
+
+128MB NOR Flash memory Map
+--------------------------
+Start Address End Address Definition Max size
+0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB
+0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB
+0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
+0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB
+0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
+0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
+0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
+0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
+0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB
+0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB
+0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
+0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB
+0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
+0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
+0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
+0xE8000000 0xE801FFFF RCW (current bank) 128KB
+
+
+T1024 Clock frequency
+---------------------
+BIN Core DDR Platform FMan
+Bin1: 1400MHz 1600MT/s 400MHz 700MHz
+Bin2: 1200MHz 1600MT/s 400MHz 600MHz
+Bin3: 1000MHz 1600MT/s 400MHz 500MHz
+
+
+Software configurations and board settings
+------------------------------------------
+1. NOR boot:
+ a. build NOR boot image
+ $ make T1024RDB_defconfig
+ $ make
+ b. program u-boot.bin image to NOR flash
+ => tftp 1000000 u-boot.bin
+ => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
+ set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
+
+ Switching between default bank0 and alternate bank4 on NOR flash
+ To change boot source to vbank4:
+ via software: run command 'cpld reset altbank' in u-boot.
+ via DIP-switch: set SW3[5:7] = '100'
+
+ To change boot source to vbank0:
+ via software: run command 'cpld reset' in u-boot.
+ via DIP-Switch: set SW3[5:7] = '000'
+
+2. NAND Boot:
+ a. build PBL image for NAND boot
+ $ make T1024RDB_NAND_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to NAND flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => nand erase 0 $filesize
+ => nand write 1000000 0 $filesize
+ set SW1[1:8] = '10001000', SW2[1] = '1', SW3[4] = '1' for NAND boot
+
+3. SPI Boot:
+ a. build PBL image for SPI boot
+ $ make T1024RDB_SPIFLASH_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to SPI flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => sf probe 0
+ => sf erase 0 f0000
+ => sf write 1000000 0 $filesize
+ set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
+
+4. SD Boot:
+ a. build PBL image for SD boot
+ $ make T1024RDB_SDCARD_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to SD/MMC card
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => mmc write 1000000 8 0x800
+ => tftp 1000000 fsl_fman_ucode_t1024_xx.bin
+ => mmc write 1000000 0x820 80
+ set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
+
+
+2-stage NAND/SPI/SD boot loader
+-------------------------------
+PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
+SPL further initializes DDR using SPD and environment variables
+and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+Run time view of SPL framework
+-------------------------------------------------
+|Area | Address |
+-------------------------------------------------
+|SecureBoot header | 0xFFFC0000 (32KB) |
+-------------------------------------------------
+|GD, BD | 0xFFFC8000 (4KB) |
+-------------------------------------------------
+|ENV | 0xFFFC9000 (8KB) |
+-------------------------------------------------
+|HEAP | 0xFFFCB000 (30KB) |
+-------------------------------------------------
+|STACK | 0xFFFD8000 (22KB) |
+-------------------------------------------------
+|U-boot SPL | 0xFFFD8000 (160KB) |
+-------------------------------------------------
+
+NAND Flash memory Map on T1024RDB
+-------------------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot 1MB(2 block)
+0x100000 0x17FFFF u-boot env 512KB(1 block)
+0x180000 0x1FFFFF FMAN Ucode 512KB(1 block)
+0x200000 0x27FFFF QE Firmware 512KB(1 block)
+
+
+SD Card memory Map on T1024RDB
+----------------------------------------------------
+Block #blocks Definition Size
+0x008 2048 u-boot img 1MB
+0x800 0016 u-boot env 8KB
+0x820 0256 FMAN Ucode 128KB
+0x920 0256 QE Firmware 128KB
+
+
+SPI Flash memory Map on T1024RDB
+----------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot img 1MB
+0x100000 0x101FFF u-boot env 8KB
+0x110000 0x12FFFF FMAN Ucode 128KB
+0x130000 0x14FFFF QE Firmware 128KB
+
+
+For more details, please refer to T1024RDB Reference Manual and access
+website www.freescale.com and Freescale QorIQ SDK Infocenter document.
diff --git a/board/freescale/t102xrdb/cpld.c b/board/freescale/t102xrdb/cpld.c
new file mode 100644
index 0000000..c03894a
--- /dev/null
+++ b/board/freescale/t102xrdb/cpld.c
@@ -0,0 +1,103 @@
+/**
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Freescale T1024RDB board-specific CPLD controlling supports.
+ *
+ * The following macros need to be defined:
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+#include "cpld.h"
+
+u8 cpld_read(unsigned int reg)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ return in_8(p + reg);
+}
+
+void cpld_write(unsigned int reg, u8 value)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ out_8(p + reg, value);
+}
+
+/**
+ * Set the boot bank to the alternate bank
+ */
+void cpld_set_altbank(void)
+{
+ u8 reg = CPLD_READ(flash_csr);
+
+ reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK;
+
+ CPLD_WRITE(flash_csr, reg);
+ CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET);
+}
+
+/**
+ * Set the boot bank to the default bank
+ */
+void cpld_set_defbank(void)
+{
+ u8 reg = CPLD_READ(flash_csr);
+
+ reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK;
+
+ CPLD_WRITE(flash_csr, reg);
+ CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET);
+}
+
+static void cpld_dump_regs(void)
+{
+ printf("cpld_ver = 0x%02x\n", CPLD_READ(cpld_ver));
+ printf("cpld_ver_sub = 0x%02x\n", CPLD_READ(cpld_ver_sub));
+ printf("hw_ver = 0x%02x\n", CPLD_READ(hw_ver));
+ printf("sw_ver = 0x%02x\n", CPLD_READ(sw_ver));
+ printf("reset_ctl1 = 0x%02x\n", CPLD_READ(reset_ctl1));
+ printf("reset_ctl2 = 0x%02x\n", CPLD_READ(reset_ctl2));
+ printf("int_status = 0x%02x\n", CPLD_READ(int_status));
+ printf("flash_csr = 0x%02x\n", CPLD_READ(flash_csr));
+ printf("fan_ctl_status = 0x%02x\n", CPLD_READ(fan_ctl_status));
+ printf("led_ctl_status = 0x%02x\n", CPLD_READ(led_ctl_status));
+ printf("sfp_ctl_status = 0x%02x\n", CPLD_READ(sfp_ctl_status));
+ printf("misc_ctl_status = 0x%02x\n", CPLD_READ(misc_ctl_status));
+ printf("boot_override = 0x%02x\n", CPLD_READ(boot_override));
+ printf("boot_config1 = 0x%02x\n", CPLD_READ(boot_config1));
+ printf("boot_config2 = 0x%02x\n", CPLD_READ(boot_config2));
+ putc('\n');
+}
+
+int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int rc = 0;
+
+ if (argc <= 1)
+ return cmd_usage(cmdtp);
+
+ if (strcmp(argv[1], "reset") == 0) {
+ if (strcmp(argv[2], "altbank") == 0)
+ cpld_set_altbank();
+ else
+ cpld_set_defbank();
+ } else if (strcmp(argv[1], "dump") == 0) {
+ cpld_dump_regs();
+ } else {
+ rc = cmd_usage(cmdtp);
+ }
+
+ return rc;
+}
+
+U_BOOT_CMD(
+ cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
+ "Reset the board or alternate bank",
+ "reset - hard reset to default bank\n"
+ "cpld reset altbank - reset to alternate bank\n"
+ "cpld dump - display the CPLD registers\n"
+ );
diff --git a/board/freescale/t102xrdb/cpld.h b/board/freescale/t102xrdb/cpld.h
new file mode 100644
index 0000000..5a3100f
--- /dev/null
+++ b/board/freescale/t102xrdb/cpld.h
@@ -0,0 +1,45 @@
+/**
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+struct cpld_data {
+ u8 cpld_ver; /* 0x00 - CPLD Major Revision Register */
+ u8 cpld_ver_sub; /* 0x01 - CPLD Minor Revision Register */
+ u8 hw_ver; /* 0x02 - Hardware Revision Register */
+ u8 sw_ver; /* 0x03 - Software Revision register */
+ u8 res0[12]; /* 0x04 - 0x0F - not used */
+ u8 reset_ctl1; /* 0x10 - Reset control Register1 */
+ u8 reset_ctl2; /* 0x11 - Reset control Register2 */
+ u8 int_status; /* 0x12 - Interrupt status Register */
+ u8 flash_csr; /* 0x13 - Flash control and status register */
+ u8 fan_ctl_status; /* 0x14 - Fan control and status register */
+ u8 led_ctl_status; /* 0x15 - LED control and status register */
+ u8 sfp_ctl_status; /* 0x16 - SFP control and status register */
+ u8 misc_ctl_status; /* 0x17 - Miscellanies ctrl & status register*/
+ u8 boot_override; /* 0x18 - Boot override register */
+ u8 boot_config1; /* 0x19 - Boot config override register*/
+ u8 boot_config2; /* 0x1A - Boot config override register*/
+} cpld_data_t;
+
+
+/* Pointer to the CPLD register set */
+
+u8 cpld_read(unsigned int reg);
+void cpld_write(unsigned int reg, u8 value);
+
+#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
+#define CPLD_WRITE(reg, value)\
+ cpld_write(offsetof(struct cpld_data, reg), value)
+
+/* CPLD on IFC */
+#define CPLD_LBMAP_MASK 0x3F
+#define CPLD_BANK_SEL_MASK 0x07
+#define CPLD_BANK_OVERRIDE 0x40
+#define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */
+#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK 0 */
+#define CPLD_LBMAP_RESET 0xFF
+#define CPLD_LBMAP_SHIFT 0x03
+#define CPLD_BOOT_SEL 0x80
diff --git a/board/freescale/t102xrdb/ddr.c b/board/freescale/t102xrdb/ddr.c
new file mode 100644
index 0000000..a20330b
--- /dev/null
+++ b/board/freescale/t102xrdb/ddr.c
@@ -0,0 +1,154 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+};
+
+/*
+ * datarate_mhz_high values need to be in ascending order
+ */
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
+ */
+ {2, 833, 0, 4, 6, 0x06060607, 0x08080807,},
+ {2, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,},
+ {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,},
+ {1, 833, 0, 4, 6, 0x06060607, 0x08080807,},
+ {1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,},
+ {1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,},
+ {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+ struct cpu_type *cpu = gd->arch.cpu;
+
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ pbsp = udimms[0];
+
+ /* Get clk_adjust according to the board ddr freqency and n_banks
+ * specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks &&
+ (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found\n");
+ printf("for data rate %lu MT/s\n", ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+ debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ",
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2);
+ debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3);
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * rtt and rtt_wr override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_OFF);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_OFF);
+
+ /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit,
+ * force DDR bus width to 32bit for T1023
+ */
+ if (cpu->soc_ver == SVR_T1023)
+ popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
+
+#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32
+ /* for DDR bus 32bit test on T1024 */
+ popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
+#endif
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
+ puts("Initializing....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+#else
+ /* DDR has been initialised by first stage boot loader */
+ dram_size = fsl_ddr_sdram_size();
+#endif
+ return dram_size;
+}
diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
new file mode 100644
index 0000000..2e400c4
--- /dev/null
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -0,0 +1,100 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+#include <asm/fsl_serdes.h>
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FMAN_ENET)
+ int i, interface;
+ struct memac_mdio_info dtsec_mdio_info;
+ struct memac_mdio_info tgec_mdio_info;
+ struct mii_dev *dev;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1;
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ dtsec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the 1G MDIO bus */
+ fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+ tgec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+ tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+ /* Register the 10G MDIO bus */
+ fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+ /* Set the two on-board RGMII PHY address */
+ fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
+
+ switch (srds_s1) {
+ case 0x95:
+ /* 10G XFI with Aquantia PHY */
+ fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
+ break;
+ default:
+ printf("SerDes protocol 0x%x is not supported on T102xRDB\n",
+ srds_s1);
+ break;
+ }
+
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ interface = fm_info_get_enet_if(i);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+ fm_info_set_mdio(i, dev);
+ break;
+ default:
+ break;
+ }
+ }
+
+ for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_XGMII:
+ dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+ fm_info_set_mdio(i, dev);
+ break;
+ default:
+ break;
+ }
+ }
+
+ cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+ return pci_eth_init(bis);
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+}
diff --git a/board/freescale/t102xrdb/law.c b/board/freescale/t102xrdb/law.c
new file mode 100644
index 0000000..1c9235f
--- /dev/null
+++ b/board/freescale/t102xrdb/law.c
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifndef CONFIG_SYS_NO_FLASH
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE_PHYS
+ SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t102xrdb/pci.c b/board/freescale/t102xrdb/pci.c
new file mode 100644
index 0000000..ba7041a
--- /dev/null
+++ b/board/freescale/t102xrdb/pci.c
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2007-2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t102xrdb/spl.c b/board/freescale/t102xrdb/spl.c
new file mode 100644
index 0000000..dd2dec4
--- /dev/null
+++ b/board/freescale/t102xrdb/spl.c
@@ -0,0 +1,107 @@
+/* Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+ return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ return CONFIG_DDR_CLK_FREQ;
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, sys_clk, ccb_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+ memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+ /* Update GD pointer */
+ gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+ console_init_f();
+
+ /* initialize selected port with appropriate baud rate */
+ sys_clk = get_board_sys_clk();
+ plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+ ccb_clk = sys_clk * plat_ratio / 2;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#if defined(CONFIG_SPL_MMC_BOOT)
+ puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ puts("\nSPI boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ puts("\nNAND boot...\n");
+#endif
+
+ relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ bd_t *bd;
+
+ bd = (bd_t *)(gd + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+ mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+ spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+ gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
+ gd->env_valid = 1;
+
+ i2c_init_all();
+
+ gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ nand_boot();
+#endif
+}
diff --git a/board/freescale/t102xrdb/t1024_pbi.cfg b/board/freescale/t102xrdb/t1024_pbi.cfg
new file mode 100644
index 0000000..7b9e9b0
--- /dev/null
+++ b/board/freescale/t102xrdb/t1024_pbi.cfg
@@ -0,0 +1,26 @@
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#Configure CPC1 as 256KB SRAM
+09010100 00000000
+09010104 fffc0007
+09010f00 08000000
+09010000 80000000
+#Configure LAW for CPC1
+09000cd0 00000000
+09000cd4 fffc0000
+09000cd8 81000011
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Configure SPI controller
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Flush PBL data
+091380c0 000FFFFF
diff --git a/board/freescale/t102xrdb/t1024_rcw.cfg b/board/freescale/t102xrdb/t1024_rcw.cfg
new file mode 100644
index 0000000..cd6f906
--- /dev/null
+++ b/board/freescale/t102xrdb/t1024_rcw.cfg
@@ -0,0 +1,8 @@
+#PBL preamble and RCW header for T1024RDB
+aa55aa55 010e0100
+#SerDes Protocol: 0x95
+#Core/DDR: 1400Mhz/1600MT/s with single source clock
+0810000c 00000000 00000000 00000000
+4a800003 80000012 ec027000 21000000
+00000000 00000000 00000000 00030810
+00000000 0b005a08 00000000 00000006
diff --git a/board/freescale/t102xrdb/t102xrdb.c b/board/freescale/t102xrdb/t102xrdb.c
new file mode 100644
index 0000000..f5c438d
--- /dev/null
+++ b/board/freescale/t102xrdb/t102xrdb.c
@@ -0,0 +1,144 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <asm/mpc85xx_gpio.h>
+#include <fm_eth.h>
+#include "t102xrdb.h"
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ struct cpu_type *cpu = gd->arch.cpu;
+ static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"};
+
+ printf("Board: %sRDB, ", cpu->name);
+ printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ",
+ CPLD_READ(hw_ver), CPLD_READ(sw_ver));
+
+#ifdef CONFIG_SDCARD
+ puts("SD/MMC\n");
+#elif CONFIG_SPIFLASH
+ puts("SPI\n");
+#else
+ u8 reg;
+
+ reg = CPLD_READ(flash_csr);
+
+ if (reg & CPLD_BOOT_SEL) {
+ puts("NAND\n");
+ } else {
+ reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
+ printf("NOR vBank%d\n", reg);
+ }
+#endif
+
+ puts("SERDES Reference Clocks:\n");
+ printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+#ifdef CONFIG_SYS_FLASH_BASE
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ int flash_esel = find_tlb_idx((void *)flashbase, 1);
+ /*
+ * Remap Boot flash region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+ if (flash_esel == -1) {
+ /* very unlikely unless something is messed up */
+ puts("Error: Could not find TLB for FLASH BASE\n");
+ flash_esel = 2; /* give our best effort to continue */
+ } else {
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+ }
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+#endif
+
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ return CONFIG_DDR_CLK_FREQ;
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+ fdt_fixup_dr_usb(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_board_enet(blob);
+#endif
+
+ return 0;
+}
+
+#ifdef CONFIG_DEEP_SLEEP
+void board_mem_sleep_setup(void)
+{
+ /* does not provide HW signals for power management */
+ CPLD_WRITE(misc_ctl_status, (CPLD_READ(misc_ctl_status) & ~0x40));
+ /* Disable MCKE isolation */
+ gpio_set_value(2, 0);
+ udelay(1);
+}
+#endif
diff --git a/board/freescale/t102xrdb/t102xrdb.h b/board/freescale/t102xrdb/t102xrdb.h
new file mode 100644
index 0000000..2f23579
--- /dev/null
+++ b/board/freescale/t102xrdb/t102xrdb.h
@@ -0,0 +1,13 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __T1024_RDB_H__
+#define __T1024_RDB_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
diff --git a/board/freescale/t102xrdb/tlb.c b/board/freescale/t102xrdb/tlb.c
new file mode 100644
index 0000000..8269b3d
--- /dev/null
+++ b/board/freescale/t102xrdb/tlb.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /*
+ * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
+ * SRAM is at 0xfffc0000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_256K, 1),
+#else
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+#ifndef CONFIG_SPL_BUILD
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 5, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 7, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 8, BOOKE_PAGESZ_16M, 1),
+#endif
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 9, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE
+ SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 11, BOOKE_PAGESZ_256K, 1),
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 12, BOOKE_PAGESZ_1G, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 13, BOOKE_PAGESZ_1G, 1)
+#endif
+ /* entry 14 and 15 has been used hard coded, they will be disabled
+ * in cpu_init_f, so if needed more, will use entry 16 later.
+ */
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);