Merge branch 'master' of git://git.denx.de/u-boot into master

Conflicts:
	drivers/power/power_fsl.c
	include/configs/mx35pdk.h
	include/configs/mx53loco.h
	include/configs/woodburn_common.h
	board/woodburn/woodburn.c

These boards still use the old old PMIC framework, so they
do not merge properly after the power framework was merged into
mainline.

Fix all conflicts and update woodburn to use Power Framework.

Signed-off-by: Stefano Babic <sbabic@denx.de>

6 files changed, 172 insertions, 8 deletions

diff --git a/board/freescale/p1_p2_rdb_pc/Makefile b/board/freescale/p1_p2_rdb_pc/Makefile
index 0dcf7d1..5b45d72 100644
--- a/board/freescale/p1_p2_rdb_pc/Makefile
+++ b/board/freescale/p1_p2_rdb_pc/Makefile
@@ -24,11 +24,27 @@ include $(TOPDIR)/config.mk
 
 LIB    = $(obj)lib$(BOARD).o
 
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+
+COBJS-y	+= spl_minimal.o tlb.o law.o
+
+else
+
 COBJS-y        += $(BOARD).o
 COBJS-y        += ddr.o
 COBJS-y        += law.o
 COBJS-y        += tlb.o
 
+endif
+
 SRCS   := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
 OBJS   := $(addprefix $(obj),$(COBJS-y))
 SOBJS  := $(addprefix $(obj),$(SOBJS))
diff --git a/board/freescale/p1_p2_rdb_pc/ddr.c b/board/freescale/p1_p2_rdb_pc/ddr.c
index 88ba56f..9355536 100644
--- a/board/freescale/p1_p2_rdb_pc/ddr.c
+++ b/board/freescale/p1_p2_rdb_pc/ddr.c
@@ -206,6 +206,7 @@ int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
 }
 #endif /* CONFIG_SYS_DDR_RAW_TIMING */
 
+#ifdef CONFIG_SYS_DDR_CS0_BNDS
 /* Fixed sdram init -- doesn't use serial presence detect. */
 phys_size_t fixed_sdram(void)
 {
@@ -260,6 +261,7 @@ phys_size_t fixed_sdram(void)
 
 	return ddr_size;
 }
+#endif
 
 void fsl_ddr_board_options(memctl_options_t *popts,
 				dimm_params_t *pdimm,
diff --git a/board/freescale/p1_p2_rdb_pc/law.c b/board/freescale/p1_p2_rdb_pc/law.c
index 0da8300..cb5e7b7 100644
--- a/board/freescale/p1_p2_rdb_pc/law.c
+++ b/board/freescale/p1_p2_rdb_pc/law.c
@@ -32,7 +32,7 @@ struct law_entry law_table[] = {
 #endif
 	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC),
 #ifdef CONFIG_SYS_NAND_BASE_PHYS
-	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC),
 #endif
 };
 
diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
index aa39260..5b5b86c 100644
--- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
+++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
@@ -177,7 +177,7 @@ void board_gpio_init(void)
 	 */
 
 	setbits_be32(&pgpio->gpdir, 0x02130000);
-#ifndef CONFIG_SYS_RAMBOOT
+#if !defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_SPL)
 	/* init DDR3 reset signal */
 	setbits_be32(&pgpio->gpdir, 0x00200000);
 	setbits_be32(&pgpio->gpodr, 0x00200000);
diff --git a/board/freescale/p1_p2_rdb_pc/spl_minimal.c b/board/freescale/p1_p2_rdb_pc/spl_minimal.c
new file mode 100644
index 0000000..09019e9
--- /dev/null
+++ b/board/freescale/p1_p2_rdb_pc/spl_minimal.c
@@ -0,0 +1,136 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ *
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <linux/compiler.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/global_data.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_SYS_INIT_L2_ADDR
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+static void sdram_init(void)
+{
+	ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+
+	__raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds);
+	__raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config);
+#if CONFIG_CHIP_SELECTS_PER_CTRL > 1
+	__raw_writel(CONFIG_SYS_DDR_CS1_BNDS, &ddr->cs1_bnds);
+	__raw_writel(CONFIG_SYS_DDR_CS1_CONFIG, &ddr->cs1_config);
+#endif
+	__raw_writel(CONFIG_SYS_DDR_TIMING_3, &ddr->timing_cfg_3);
+	__raw_writel(CONFIG_SYS_DDR_TIMING_0, &ddr->timing_cfg_0);
+	__raw_writel(CONFIG_SYS_DDR_TIMING_1, &ddr->timing_cfg_1);
+	__raw_writel(CONFIG_SYS_DDR_TIMING_2, &ddr->timing_cfg_2);
+
+	__raw_writel(CONFIG_SYS_DDR_CONTROL_2, &ddr->sdram_cfg_2);
+	__raw_writel(CONFIG_SYS_DDR_MODE_1, &ddr->sdram_mode);
+	__raw_writel(CONFIG_SYS_DDR_MODE_2, &ddr->sdram_mode_2);
+
+	__raw_writel(CONFIG_SYS_DDR_INTERVAL, &ddr->sdram_interval);
+	__raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init);
+	__raw_writel(CONFIG_SYS_DDR_CLK_CTRL, &ddr->sdram_clk_cntl);
+
+	__raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4);
+	__raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5);
+	__raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl);
+	__raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL, &ddr->ddr_wrlvl_cntl);
+
+	/* Set, but do not enable the memory */
+	__raw_writel(CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN, &ddr->sdram_cfg);
+
+	asm volatile("sync;isync");
+	udelay(500);
+
+	/* Let the controller go */
+	out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN);
+
+	set_next_law(0, CONFIG_SYS_SDRAM_SIZE_LAW, LAW_TRGT_IF_DDR_1);
+}
+#endif
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+#ifndef CONFIG_QE
+	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+#endif
+
+	/* initialize selected port with appropriate baud rate */
+	plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+	plat_ratio >>= 1;
+	gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+			gd->bus_clk / 16 / CONFIG_BAUDRATE);
+
+	puts("\nNAND boot... ");
+
+#ifndef CONFIG_QE
+	/* init DDR3 reset signal */
+	__raw_writel(0x02000000, &pgpio->gpdir);
+	__raw_writel(0x00200000, &pgpio->gpodr);
+	__raw_writel(0x00000000, &pgpio->gpdat);
+	udelay(1000);
+	__raw_writel(0x00200000, &pgpio->gpdat);
+	udelay(1000);
+	__raw_writel(0x00000000, &pgpio->gpdir);
+#endif
+
+#ifndef CONFIG_SYS_INIT_L2_ADDR
+	/* Initialize the DDR3 */
+	sdram_init();
+#endif
+
+	/* copy code to RAM and jump to it - this should not return */
+	/* NOTE - code has to be copied out of NAND buffer before
+	 * other blocks can be read.
+	 */
+	relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	nand_boot();
+}
+
+void putc(char c)
+{
+	if (c == '\n')
+		NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+
+	NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+}
+
+void puts(const char *str)
+{
+	while (*str)
+		putc(*str++);
+}
diff --git a/board/freescale/p1_p2_rdb_pc/tlb.c b/board/freescale/p1_p2_rdb_pc/tlb.c
index 6d22463..3e4dffd 100644
--- a/board/freescale/p1_p2_rdb_pc/tlb.c
+++ b/board/freescale/p1_p2_rdb_pc/tlb.c
@@ -53,7 +53,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 			0, 1, BOOKE_PAGESZ_1M, 1),
 
-#ifndef CONFIG_NAND_SPL
+#ifndef CONFIG_SPL_BUILD
 	/* W**G* - Flash/promjet, localbus */
 	/* This will be changed to *I*G* after relocation to RAM. */
 	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
@@ -85,7 +85,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 	SET_TLB_ENTRY(1, CONFIG_SYS_PMC_BASE, CONFIG_SYS_PMC_BASE_PHYS,
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 			0, 10, BOOKE_PAGESZ_64K, 1),
-#endif
+#endif /* not SPL */
 
 #ifdef CONFIG_SYS_NAND_BASE
 	/* *I*G - NAND */
@@ -94,7 +94,17 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			0, 7, BOOKE_PAGESZ_1M, 1),
 #endif
 
-#ifdef CONFIG_SYS_RAMBOOT
+#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL)
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+	/* L2SRAM */
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 8, BOOKE_PAGESZ_256K, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
+		      CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 12, BOOKE_PAGESZ_256K, 1),
+#else
 	/* *I*G - eSDHC/eSPI/NAND boot */
 	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
 			MAS3_SX|MAS3_SW|MAS3_SR, 0,
@@ -106,9 +116,9 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 			0, 9, BOOKE_PAGESZ_1G, 1),
-#endif
-#endif
-
+#endif /* P1020MBG */
+#endif /* not L2 SRAM */
+#endif /* RAMBOOT/SPL */
 };
 
 int num_tlb_entries = ARRAY_SIZE(tlb_table);