Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  davinci: Remove unwanted memsize.c from hawkboard's nand spl build
  devkit8000: Move CONFIG_SYS_TEXT_BASE out of bss
  da850evm: pass board revision info to kernel
  arch/arm/include/asm/arch-omap5/clocks.h: Fix GCC 4.2 warnings
  arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix GCC 4.6 warnings
  arch/arm/cpu/armv7/omap-common/spl.c: Fix GCC 4.2 warnings
  MX35: flea3: changes due to hardware revision B
  MX: serial_mxc: cleanup removing nasty #ifdef
  M28: Fix OB1 bug in GPIO driver
  MXS: Add static annotations to dma driver
  apbh_dma: return error value on timeout
  Efika: Configure additional regulators for HDMI output
  mx5: Correct a warning in clock.c
  MC13892: Add REGMODE0 bits definitions
  mx51evk: Configure the pins as GPIOs prior to using gpio_get_value
  mx53smd: Configure the pins as GPIOs prior to using gpio_get_value
  mx53evk: Configure the pins as GPIOs prior to using gpio_get_value
  mx53ard: Configure the pins as GPIOs prior to using gpio_get_value
  mx53loco: Configure the pins as GPIOs prior to using gpio_get_value
  OMAP3: Add SPL_BOARD_INIT hook
  AM3517 CraneBoard: Add SPL support
  AM3517: Add SPL support
  OMAP3: Add SPL support to omap3_evm
  OMAP3: Add SPL support to Beagleboard
  OMAP3 SPL: Add identify_nand_chip function
  OMAP3 SPL: Rework memory initalization and devkit8000 support
  OMAP3: Suffix all Micron memory timing parts with their speed
  OMAP3: Add optimal SDRC autorefresh control values
  omap3: mem: Add MCFG helper macro
  OMAP3: Remove get_mem_type prototype
  OMAP3: Change mem_ok to clear again after reading back
  OMAP3: Add a helper function to set timings in SDRC
  OMAP3: Update SDRC dram_init to always call make_cs1_contiguous()
  omap3: mem: Comment enable_gpmc_cs_config more
  ARM: davici_emac: Fix condition for number of phy detects
  arm: printf() is not available in some SPL configurations
  arm, davinci: add support for am1808 based enbw_cmc board
  arm, davinci: move misc function in arch tree
  arm, board/davinci/common/misc.c: Codingstyle cleanup
  arm, davinci, da850: add uart1 tx rx pinmux config
  arm, davinci: move davinci_rtc struct to hardware.h
  arm, davinci: Remove duplication of pinmux configuration code
  arm, hawkboard: Use the pinmux configurations defined in the arch tree
  arm, da850evm: Use the pinmux configurations defined in the arch tree
  arm, da850: Add pinmux configurations to the arch tree
  arm, da850evm: Do pinmux configuration for EMAC together with other pinmuxes
  arm, hawkboard: Remove obsolete struct pinmux_config i2c_pins
  arm, davinci: Move pinmux functions from board to arch tree
  arm, arm926ejs: always do cpu critical inits
  omap_gpmc: use SOFTECC in SPL if it's enabled
  nand_spl_simple: add support for software ECC
  AM3517: move AM3517 specific mux defines to generic header
  AM35xx: add EMAC support
  davinci_emac: hardcode 100Mbps for AM35xx and RMII
  davinci_emac: fix for running with dcache enabled
  arm926ejs: add noop implementation for dcache ops
  davinci_emac: conditionally compile specific PHY support
  davinci_emac: use internal addresses in buffer descriptors
  davinci_emac: move arch-independent defines to separate header
  BeagleBoard: config: Really switch to ttyO2
  ARM: davinci_dm6467Tevm: Fix build breakage
  ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused
  ARM: OMAP3: Remove unused define SDRC_R_C_B
  ARM: OMAP3: Remove unused define CONFIG_OMAP3430
  omap4: fix IO setting
  omap4+: streamline CONFIG_SYS_TEXT_BASE and other SDRAM addresses
  omap4460: add ES1.1 identification
  omap4: emif: fix error in driver
  omap: remove I2C from SPL
  omap4460: fix TPS initialization
  omap: fix cache line size for omap3/omap4 boards
  omap4: ttyO2 instead of ttyS2 in default bootargs
  omap: Improve PLL parameter calculation tool
  start.S: remove omap3 specific code from start.S
  armv7: setup vector
  armv7: include armv7/cpu.c in SPL build
  armv7: disable L2 cache in cleanup_before_linux()
  arm, arm926ejs: Fix clear bss loop for zero length bss
  PXA: Move colibri_pxa270 to board/toradex/
  PXA: Flip colibri_pxa27x to pxa-common.h
  PXA: Introduce common configuration header for PXA
  PXA: Rename pxa_dram_init to pxa2xx_dram_init
  PXA: Squash extern pxa_dram_init()
  PXA: Export cpu_is_ and pxa_dram_init functions
  PXA: Cleanup Colibri PXA270
  PXA: Replace timer driver
  PXA: Add cpuinfo display for PXA2xx
  PXA: Separate PXA2xx CPU init
  PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]X
  PXA: Unify vpac270 environment size
  PXA: Enable command line editing for vpac270
  PXA: Adapt Voipac PXA270 to OneNAND SPL
  PXA: Drop Voipac PXA270 OneNAND IPL
  PXA: Fixup PXA25x boards after start.S update
  PXA: Re-add the Dcache locking as RAM for pxa250
  PXA: Rework start.S to be closer to other ARMs
  PXA: Drop XM250 board
  PXA: Drop PLEB2 board
  PXA: Drop CRADLE board
  PXA: Drop CERF250 board
  Fix regression in SMDK6400
  nand: Add common functions to linux/mtd/nand.h
  Ethernut 5 board support
  net: Armada100: Fix compilation warnings
  ARM: remove duplicated code for LaCie boards
  ARM: add support for LaCie 2Big Network v2
  mvsata: fix ide_preinit for missing disks
  netspace_v2: Read Ethernet MAC address from EEPROM
  omap3evm: Add support for EFI partitions
  part_efi: Fix compile errors

1 files changed, 270 insertions, 0 deletions

diff --git a/board/egnite/ethernut5/ethernut5.c b/board/egnite/ethernut5/ethernut5.c
new file mode 100644
index 0000000..e42e91e
--- /dev/null
+++ b/board/egnite/ethernut5/ethernut5.c
@@ -0,0 +1,270 @@
+/*
+ * (C) Copyright 2011
+ * egnite GmbH <info@egnite.de>
+ *
+ * (C) Copyright 2010
+ * Ole Reinhardt <ole.reinhardt@thermotemp.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Ethernut 5 general board support
+ *
+ * Ethernut is an open source hardware and software project for
+ * embedded Ethernet devices. Hardware layouts and CAD files are
+ * freely available under BSD-like license.
+ *
+ * Ethernut 5 is the first member of the Ethernut board family
+ * with U-Boot and Linux support. This implementation is based
+ * on the original work done by Ole Reinhardt, but heavily modified
+ * to support additional features and the latest board revision 5.0F.
+ *
+ * Main board components are by default:
+ *
+ * Atmel AT91SAM9XE512 CPU with 512 kBytes NOR Flash
+ * 2 x 64 MBytes Micron MT48LC32M16A2P SDRAM
+ * 512 MBytes Micron MT29F4G08ABADA NAND Flash
+ * 4 MBytes Atmel AT45DB321D DataFlash
+ * SMSC LAN8710 Ethernet PHY
+ * Atmel ATmega168 MCU used for power management
+ * Linear Technology LTC4411 PoE controller
+ *
+ * U-Boot relevant board interfaces are:
+ *
+ * 100 Mbit Ethernet with IEEE 802.3af PoE
+ * RS-232 serial port
+ * USB host and device
+ * MMC/SD-Card slot
+ * Expansion port with I2C, SPI and more...
+ *
+ * Typically the U-Boot image is loaded from serial DataFlash into
+ * SDRAM by the samboot boot loader, which is located in internal
+ * NOR Flash and provides all essential initializations like CPU
+ * and peripheral clocks and, of course, the SDRAM configuration.
+ *
+ * For testing purposes it is also possibly to directly transfer
+ * the image into SDRAM via JTAG. A tested configuration exists
+ * for the Turtelizer 2 hardware dongle and the OpenOCD software.
+ * In this case the latter will do the basic hardware configuration
+ * via its reset-init script.
+ *
+ * For additional information visit the project home page at
+ * http://www.ethernut.de/
+ */
+
+#include <common.h>
+#include <net.h>
+#include <netdev.h>
+#include <miiphy.h>
+#include <i2c.h>
+#include <spi.h>
+#include <dataflash.h>
+#include <mmc.h>
+
+#include <asm/arch/at91sam9260.h>
+#include <asm/arch/at91sam9260_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_spi.h>
+#include <asm/arch/gpio.h>
+#include <asm/io.h>
+
+#include "ethernut5_pwrman.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+AT91S_DATAFLASH_INFO dataflash_info[CONFIG_SYS_MAX_DATAFLASH_BANKS];
+
+struct dataflash_addr cs[CONFIG_SYS_MAX_DATAFLASH_BANKS] = {
+	{CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0, 0}
+};
+
+/*
+ * In fact we have 7 partitions, but u-boot supports 5 only. This is
+ * no big deal, because the first partition is reserved for applications
+ * and the last one is used by Nut/OS. Both need not to be visible here.
+ */
+dataflash_protect_t area_list[NB_DATAFLASH_AREA] = {
+	{ 0x00021000, 0x00041FFF, FLAG_PROTECT_SET, 0, "setup" },
+	{ 0x00042000, 0x000C5FFF, FLAG_PROTECT_SET, 0, "uboot" },
+	{ 0x000C6000, 0x00359FFF, FLAG_PROTECT_SET, 0, "kernel" },
+	{ 0x0035A000, 0x003DDFFF, FLAG_PROTECT_SET, 0, "nutos" },
+	{ 0x003DE000, 0x003FEFFF, FLAG_PROTECT_CLEAR, 0, "env" }
+};
+
+/*
+ * This is called last during early initialization. Most of the basic
+ * hardware interfaces are up and running.
+ *
+ * The SDRAM hardware has been configured by the first stage boot loader.
+ * We only need to announce its size, using u-boot's memory check.
+ */
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size(
+			(void *)CONFIG_SYS_SDRAM_BASE,
+			CONFIG_SYS_SDRAM_SIZE);
+	return 0;
+}
+
+#ifdef CONFIG_CMD_NAND
+static void ethernut5_nand_hw_init(void)
+{
+	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	unsigned long csa;
+
+	/* Assign CS3 to NAND/SmartMedia Interface */
+	csa = readl(&matrix->ebicsa);
+	csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
+	writel(csa, &matrix->ebicsa);
+
+	/* Configure SMC CS3 for NAND/SmartMedia */
+	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+		AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+		&smc->cs[3].setup);
+	writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
+		AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
+		&smc->cs[3].pulse);
+	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+		&smc->cs[3].cycle);
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+		AT91_SMC_MODE_EXNW_DISABLE |
+		AT91_SMC_MODE_DBW_8 |
+		AT91_SMC_MODE_TDF_CYCLE(2),
+		&smc->cs[3].mode);
+
+#ifdef CONFIG_SYS_NAND_READY_PIN
+	/* Ready pin is optional. */
+	at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+#endif
+	at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+}
+#endif
+
+/*
+ * This is called first during late initialization.
+ */
+int board_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+	/* Enable clocks for all PIOs */
+	writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
+		(1 << ATMEL_ID_PIOC),
+		&pmc->pcer);
+	/* Set adress of boot parameters. */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+	/* Initialize UARTs and power management. */
+	at91_seriald_hw_init();
+	ethernut5_power_init();
+#ifdef CONFIG_CMD_NAND
+	ethernut5_nand_hw_init();
+#endif
+#ifdef CONFIG_HAS_DATAFLASH
+	at91_spi0_hw_init(1 << 0);
+#endif
+	return 0;
+}
+
+#ifdef CONFIG_MACB
+/*
+ * This is optionally called last during late initialization.
+ */
+int board_eth_init(bd_t *bis)
+{
+	const char *devname;
+	unsigned short mode;
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+	/* Enable on-chip EMAC clock. */
+	writel(1 << ATMEL_ID_EMAC0, &pmc->pcer);
+	/* Need to reset PHY via power management. */
+	ethernut5_phy_reset();
+	/* Set peripheral pins. */
+	at91_macb_hw_init();
+	/* Basic EMAC initialization. */
+	if (macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, CONFIG_PHY_ID))
+		return -1;
+	/*
+	 * Early board revisions have a pull-down at the PHY's MODE0
+	 * strap pin, which forces the PHY into power down. Here we
+	 * switch to all-capable mode.
+	 */
+	devname = miiphy_get_current_dev();
+	if (miiphy_read(devname, 0, 18, &mode) == 0) {
+		/* Set mode[2:0] to 0b111. */
+		mode |= 0x00E0;
+		miiphy_write(devname, 0, 18, mode);
+		/* Soft reset overrides strap pins. */
+		miiphy_write(devname, 0, MII_BMCR, BMCR_RESET);
+	}
+	/* Sync environment with network devices, needed for nfsroot. */
+	return eth_init(gd->bd);
+}
+#endif
+
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+int board_mmc_init(bd_t *bd)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+	/* Enable MCI clock. */
+	writel(1 << ATMEL_ID_MCI, &pmc->pcer);
+	/* Initialize MCI hardware. */
+	at91_mci_hw_init();
+	/* Register the device. */
+	return atmel_mci_init((void *)ATMEL_BASE_MCI);
+}
+
+int board_mmc_getcd(u8 *cd, struct mmc *mmc)
+{
+	*cd = at91_get_pio_value(CONFIG_SYS_MMC_CD_PIN) ? 1 : 0;
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_ATMEL_SPI
+/*
+ * Note, that u-boot uses different code for SPI bus access. While
+ * memory routines use automatic chip select control, the serial
+ * flash support requires 'manual' GPIO control. Thus, we switch
+ * modes.
+ */
+void spi_cs_activate(struct spi_slave *slave)
+{
+	/* Enable NPCS0 in GPIO mode. This disables peripheral control. */
+	at91_set_pio_output(AT91_PIO_PORTA, 3, 0);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+	/* Disable NPCS0 in GPIO mode. */
+	at91_set_pio_output(AT91_PIO_PORTA, 3, 1);
+	/* Switch back to peripheral chip select control. */
+	at91_set_a_periph(AT91_PIO_PORTA, 3, 1);
+}
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+	return bus == 0 && cs == 0;
+}
+#endif