ARM DaVinci: Add common peripherals and modules enable functions.

Taken all the duplicated code for enabling common modules and apply
software workarounds from the board specific code into common
functions. Also added comments explaining the workarounds
(from TI errata documents) and replaced some numerical bit numbers
with more meaningful defines.

Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>

1 files changed, 65 insertions, 0 deletions

diff --git a/board/davinci/common/psc.c b/board/davinci/common/psc.c
index d538d51..28e2a4b 100644
--- a/board/davinci/common/psc.c
+++ b/board/davinci/common/psc.c
@@ -26,6 +26,14 @@
 #include <common.h>
 #include <asm/arch/hardware.h>
 
+#define PINMUX0_EMACEN (1 << 31)
+#define PINMUX0_AECS5  (1 << 11)
+#define PINMUX0_AECS4  (1 << 10)
+
+#define PINMUX1_I2C    (1 <<  7)
+#define PINMUX1_UART1  (1 <<  1)
+#define PINMUX1_UART0  (1 <<  0)
+
 /*
  * The DM6446 includes two separate power domains: "Always On" and "DSP". The
  * "Always On" power domain is always on when the chip is on. The "Always On"
@@ -115,3 +123,60 @@ void dsp_on(void)
 	REG(PSC_GBLCTL) &= ~0x1f;
 }
 #endif /* CONFIG_SYS_USE_DSPLINK */
+
+void davinci_enable_uart0(void)
+{
+	lpsc_on(DAVINCI_LPSC_UART0);
+
+	/* Bringup UART0 out of reset */
+	REG(UART0_PWREMU_MGMT) = 0x0000e003;
+
+	/* Enable UART0 MUX lines */
+	REG(PINMUX1) |= PINMUX1_UART0;
+}
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+void davinci_enable_emac(void)
+{
+	lpsc_on(DAVINCI_LPSC_EMAC);
+	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
+	lpsc_on(DAVINCI_LPSC_MDIO);
+
+	/* Enable GIO3.3V cells used for EMAC */
+	REG(VDD3P3V_PWDN) = 0;
+
+	/* Enable EMAC. */
+	REG(PINMUX0) |= PINMUX0_EMACEN;
+}
+#endif
+
+void davinci_enable_i2c(void)
+{
+	lpsc_on(DAVINCI_LPSC_I2C);
+
+	/* Enable I2C pin Mux */
+	REG(PINMUX1) |= PINMUX1_I2C;
+}
+
+void davinci_errata_workarounds(void)
+{
+	/*
+	 * Workaround for TMS320DM6446 errata 1.3.22:
+	 *   PSC: PTSTAT Register Does Not Clear After Warm/Maximum Reset
+	 *   Revision(s) Affected: 1.3 and earlier
+	 */
+	REG(PSC_SILVER_BULLET) = 0;
+
+	/*
+	 * Set the PR_OLD_COUNT bits in the Bus Burst Priority Register (PBBPR)
+	 * as suggested in TMS320DM6446 errata 2.1.2:
+	 *
+	 * On DM6446 Silicon Revision 2.1 and earlier, under certain conditions
+	 * low priority modules can occupy the bus and prevent high priority
+	 * modules like the VPSS from getting the required DDR2 throughput.
+	 * A hex value of 0x20 should provide a good ARM (cache enabled)
+	 * performance and still allow good utilization by the VPSS or other
+	 * modules.
+	 */
+	REG(VBPR) = 0x20;
+}