Add board support for hawkboard

The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.

The following bootup procedure is used.

At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.

Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
 u-boot.bin image to the RAM from u-boot, and flash to the nand flash
 at address 0xe0000.

* hawkboard_nand_config - Used to generate the secondary
 bootloader(nand_spl) image. This creates an elf file u-boot-spl
 under nand_spl/. Create an AIS signed image using this file, and
 flash it to the nand flash at address 0x20000. The ais file should
 fit in one block.

* hawkboard_uart_config - This is same as the first image, but with
 the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

1 files changed, 0 insertions, 75 deletions

diff --git a/board/davinci/common/misc.c b/board/davinci/common/misc.c
index a30047b..f25ad7e 100644
--- a/board/davinci/common/misc.c
+++ b/board/davinci/common/misc.c
@@ -95,78 +95,3 @@ void davinci_sync_env_enetaddr(uint8_t *rom_enetaddr)
 }
 
 #endif	/* DAVINCI_EMAC */
-
-/*
- * Change the setting of a pin multiplexer field.
- *
- * Takes an array of pinmux settings similar to:
- *
- * struct pinmux_config uart_pins[] = {
- *	{ &davinci_syscfg_regs->pinmux[8], 2, 7 },
- *	{ &davinci_syscfg_regs->pinmux[9], 2, 0 }
- * };
- *
- * Stepping through the array, each pinmux[n] register has the given value
- * set in the pin mux field specified.
- *
- * The number of pins in the array must be passed (ARRAY_SIZE can provide
- * this value conveniently).
- *
- * Returns 0 if all field numbers and values are in the correct range,
- * else returns -1.
- */
-int davinci_configure_pin_mux(const struct pinmux_config *pins,
-			      const int n_pins)
-{
-	int i;
-
-	/* check for invalid pinmux values */
-	for (i = 0; i < n_pins; i++) {
-		if (pins[i].field >= PIN_MUX_NUM_FIELDS ||
-		    (pins[i].value & ~PIN_MUX_FIELD_MASK) != 0)
-			return -1;
-	}
-
-	/* configure the pinmuxes */
-	for (i = 0; i < n_pins; i++) {
-		const int offset = pins[i].field * PIN_MUX_FIELD_SIZE;
-		const unsigned int value = pins[i].value << offset;
-		const unsigned int mask = PIN_MUX_FIELD_MASK << offset;
-		const dv_reg *mux = pins[i].mux;
-
-		writel(value | (readl(mux) & (~mask)), mux);
-	}
-
-	return 0;
-}
-
-/*
- * Configure multiple pinmux resources.
- *
- * Takes an pinmux_resource array of pinmux_config and pin counts:
- *
- * const struct pinmux_resource pinmuxes[] = {
- *	PINMUX_ITEM(uart_pins),
- *	PINMUX_ITEM(i2c_pins),
- * };
- *
- * The number of items in the array must be passed (ARRAY_SIZE can provide
- * this value conveniently).
- *
- * Each item entry is configured in the defined order. If configuration
- * of any item fails, -1 is returned and none of the following items are
- * configured. On success, 0 is returned.
- */
-int davinci_configure_pin_mux_items(const struct pinmux_resource *item,
-				    const int n_items)
-{
-	int i;
-
-	for (i = 0; i < n_items; i++) {
-		if (davinci_configure_pin_mux(item[i].pins,
-					      item[i].n_pins) != 0)
-			return -1;
-	}
-
-	return 0;
-}