Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm: (212 commits)
  ARM: cache: Move the cp15 CR register read before flushing the cache.
  ARM: introduce arch_early_init_r()
  PXA: Enable CONFIG_PREBOOT on zipitz2
  ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
  No need to define CONFIG_ARCH_CPU_INIT.
  add new board vl_ma2sc
  MTD: SPEAr SMI: Add write support for length < 4 bytes
  i2c: designware_i2c.c: Add support for the "i2c probe" command
  rtc/m41t62: Add support for M41T82 with HT (Halt Update)
  SPL: ARM: spear: Add SPL support for SPEAr600 platform
  Makefile: Add u-boot.spr build target (SPEAr)
  SPL: ARM: spear: Remove some objects from SPL build
  SPL: lib/Makefile: Add crc32.c to SPL build
  SPL: common/Makefile: Add image.c to SPL build
  arm: Don't use printf() in SPL builds
  GPIO: Add SPEAr GPIO driver
  net: Multiple updates/enhancements to designware.c
  cleanup/SPEAr: Define configuration flags more elegantly
  cleanup/SPEAr: Remove unnecessary parenthesis
  SPEAr: Correct SoC ID offset in misc configuration space
  SPEAr: explicitly select clk src for UART
  SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
  SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
  SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
  SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
  SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
  SPEAr: Enable dcache for fast file transfer
  SPEAr: Enable autoneg for ethernet
  SPEAr: Enable udc and usb-console support only for usbtty configuration
  SPEAr: Enable usb device high speed support
  SPEAr: Initialize SNOR in early_board_init_f
  SPEAr: Change the default environment variables
  SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
  SPEAr: Add configuration options for spear3xx and spear6xx boards
  SPEAr: Add basic arch related support for SPEAr SoCs
  SPEAr: Add interface information in initialization
  SPEAr: Add macb driver support for spear310 and spear320
  SPEAr: Configure network support for spear SoCs
  SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
  SPEAr: Eliminate dependency on Xloader table
  SPEAr: Fix ARM relocation support
  st_smi: Fixed page size for Winbond W25Q128FV flash
  st_smi: Change timeout loop implementation
  st_smi: Fix bug in flash_print_info()
  st_smi: Change the flash probing method
  st_smi: Removed no needed dependency on ST_M25Pxx_ID
  st_smi: Fix smi read status
  st_smi: Move status register read before modifying ctrl register
  st_smi: Read status until timeout happens
  st_smi: Enhance the error handling
  st_smi: Change SMI timeout values
  st_smi: Return error in case TFF is not set
  st_smi: Add support for SPEAr SMI driver
  mtd/NAND: Remove obsolete SPEAr specific NAND drivers
  SPEAr: Configure FSMC driver for NAND interface
  mtd/NAND: Add FSMC driver support
  arm/km: remove calls to kw_gpio_* in board_early_init_f
  arm/km: add implementation for read_dip_switch
  arm/km: support the 2 PCIe fpga resets
  arm/km: skip FPGA config when already configured
  arm/km: redefine piggy 4 reg names to avoid conflicts
  arm/km: cleanup km_kirkwood boards
  arm/km: enable BOCO2 FPGA download support
  arm/km: remove portl2.h and use km_kirkwood instead
  arm/km: convert mgcoge3un target to km_kirkwood
  arm/km: add kmcoge5un board support
  arm/km: add kmnusa board support
  arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
  cm-t35: fix incorrect NAND_ECC layout selection
  ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
  ARM: OMAP4/5: Move USB pads to essential list.
  ARM: OMAP4/5: Move USB clocks to essential group.
  ARM: OMAP4/5: Move gpmc clocks to essential group.
  ARM: OMAP4+: Move external phy initialisations to arch specific place.
  omap4: Use a smaller M,N couple for IVA DPLL
  da850/omap-l138: Enable auto negotiation in RMII mode
  omap: am33xx: accomodate input clocks other than 24 Mhz
  omap: emif: fix bug in manufacturer code test
  omap: emif: deal with rams that return duplicate mr data on all byte lanes
  OMAP4+: Force DDR in self-refresh after warm reset
  OMAP4+: Handle sdram init after warm reset
  ARM: OMAP3+: Detect reset type
  arm: bugfix: Move vector table before jumping relocated code
  Kirkwood: Add support for Ka-Ro TK71
  arm/km: use spi claim bus to switch between SPI and NAND
  arm/kirkwood: protect the ENV_SPI #defines
  ARM: don't probe PHY address for LaCie boards
  lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
  lacie_kw: fix SDRAM banks number for net2big_v2
  Kirkwood: add lschlv2 and lsxhl board support
  net: add helper to generate random mac address
  net: use common rand()/srand() functions
  lib: add rand() function
  kwboot: boot kirkwood SoCs over a serial link
  kw_spi: add weak functions board_spi_claim/release_bus
  kw_spi: support spi_claim/release_bus functions
  kw_spi: backup and reset the MPP of the chosen CS pin
  kirkwood: fix calls to kirkwood_mpp_conf
  kirkwood: add save functionality kirkwood_mpp_conf function
  km_arm: use filesize for erase in update command
  arm/km: enable mii cmd
  arm/km: remove CONFIG_RESET_PHY_R
  arm/km: change maintainer for mgcoge3un
  arm/km: fix wrong comment in SDRAM config for mgcoge3un
  arm/km: use ARRAY_SIZE macro
  arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
  arm/km: add piggy mac adress offset for mgcoge3un
  arm/km: add board type to boards.cfg
  AT91SAM9*: Change kernel address in dataflash to match u-boot's size
  ATMEL/PIO: Enable new feature of PIO on Atmel device
  ehci-atmel: fix compiler warning
  AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
  Atmel : usb : add EHCI driver for Atmel SoC
  Fix: AT91SAM9263 nor flash usage
  Fix: broken boot message at serial line on AT91SAM9263-EK board
  i.MX6 USDHC: Use the ESDHC clock
  mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
  i.MX28: Add function to adjust memory parameters
  mx28evk: Fix PSWITCH key position
  mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
  mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
  imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53ard: Remove unused CONFIG_MII_GASKET
  mx6: Avoid writing to read-only bits in imximage.cfg
  m28evk: use same notation to alloc the 128kB stack
  ...

Signed-off-by: Wolfgang Denk <wd@denx.de>

1 files changed, 229 insertions, 0 deletions

diff --git a/board/buffalo/lsxl/kwbimage-lsxhl.cfg b/board/buffalo/lsxl/kwbimage-lsxhl.cfg
new file mode 100644
index 0000000..8a94b6c
--- /dev/null
+++ b/board/buffalo/lsxl/kwbimage-lsxhl.cfg
@@ -0,0 +1,229 @@
+#
+# Copyright (c) 2012 Michael Walle
+# Michael Walle <michael@walle.cc>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM spi
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0/1 interface pad voltage to 1.8V
+DATA 0xFFD100E0 0x1B1B9B9B
+
+# L2 RAM Timing 0
+DATA 0xFFD20134 0xBBBBBBBB
+# not further specified in HW manual, timing taken from original vendor port
+
+# L2 RAM Timing 1
+DATA 0xFFD20138 0x00BBBBBB
+# not further specified in HW manual, timing taken from original vendor port
+
+# DDR Configuration register
+DATA 0xFFD01400 0x43000618
+# bit13-0:  0x618, 1560 DDR2 clks refresh rate
+# bit23-14: 0 required
+# bit24:    1, enable exit self refresh mode on DDR access
+# bit25:    1 required
+# bit29-26: 0 required
+# bit31-30: 0b01 required
+
+# DDR Controller Control Low
+DATA 0xFFD01404 0x39543010
+# bit3-0:   0 required
+# bit4:     1, T2 mode, addr/cmd are driven for two cycles
+# bit5:     0, clk is driven during self refresh, we don't care for APX
+# bit6:     0, use recommended falling edge of clk for addr/cmd
+# bit11-7:  0 required
+# bit12:    1 required
+# bit13:    1 required
+# bit14:    0, input buffer always powered up
+# bit17-15: 0 required
+# bit18:    1, cpu lock transaction enabled
+# bit19:    0 required
+# bit23-20: 5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 9, CL+4, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31:    0, no additional STARTBURST delay
+
+# DDR Timing (Low)
+DATA 0xFFD01408 0x22125441
+# bit3-0:   0x1, 18 cycle tRAS (tRAS[3-0])
+# bit7-4:   4, 5 cycle tRCD
+# bit11-8:  4, 5 cyle tRP
+# bit15-12: 5, 6 cyle tWR
+# bit19-16: 2, 3 cyle tWTR
+# bit20:    1, 18 cycle tRAS (tRAS[4])
+# bit23-21: 0 required
+# bit27-24: 2, 3 cycle tRRD
+# bit31-28: 2, 3 cyle tRTP
+
+# DDR Timing (High)
+DATA 0xFFD0140C 0x00000832
+# bit6-0:   0x32, 50 cycle tRFC
+# bit8-7:   0, 1 cycle tR2R
+# bit10-9:  0, 1 cyle tR2W
+# bit12-11: 1, 2 cylce tW2W
+# bit31-13: 0 required
+
+# DDR Address Control
+DATA 0xFFD01410 0x0000000C
+# bit1-0:   0, Cs0width=x8
+# bit3-2:   3, Cs0size=1Gbit
+# bit5-4:   0, Cs1width=nonexistent
+# bit7-6:   0, Cs1size=nonexistent
+# bit9-8:   0, Cs2width=nonexistent
+# bit11-10: 0, Cs2size=nonexistent
+# bit13-12: 0, Cs3width=nonexistent
+# bit15-14: 0, Cs3size=nonexistent
+# bit16:    0, Cs0AddrSel
+# bit17:    0, Cs1AddrSel
+# bit18:    0, Cs2AddrSel
+# bit19:    0, Cs3AddrSel
+# bit31-20: 0 required
+
+# DDR Open Pages Control
+DATA 0xFFD01414 0x00000000
+# bit0:    0, OPEn=OpenPage enabled
+# bit31-1: 0 required
+
+# DDR Operation
+DATA 0xFFD01418 0x00000000
+# bit3-0:   0, Cmd=Normal SDRAM Mode
+# bit31-4:  0 required
+
+# DDR Mode
+DATA 0xFFD0141C 0x00000652
+# bit2-0:   2, Burst Length (2 required)
+# bit3:     0, Burst Type (0 required)
+# bit6-4:   5, CAS Latency (CL) 5
+# bit7:     0, (Test Mode) Normal operation
+# bit8:     0, (Reset DLL) Normal operation
+# bit11-9:  3, Write recovery for auto-precharge (3 required)
+# bit12:    0, Fast Active power down exit time (0 required)
+# bit31-13: 0 required
+
+# DDR Extended Mode
+DATA 0xFFD01420 0x00000006
+# bit0:     0, DRAM DLL enabled
+# bit1:     1, DRAM drive strength reduced
+# bit2:     1, ODT control Rtt[0] (Rtt=1, 75 ohm termination)
+# bit5-3:   0 required
+# bit6:     0, ODT control Rtt[1] (Rtt=1, 75 ohm termination)
+# bit9-7:   0 required
+# bit10:    0, differential DQS enabled
+# bit11:    0 required
+# bit12:    0, DRAM output buffer enabled
+# bit31-13: 0 required
+
+# DDR Controller Control High
+DATA 0xFFD01424 0x0000F17F
+# bit2-0:   0x7 required
+# bit3:     1, MBUS Burst Chop disabled
+# bit6-4:   0x7 required
+# bit7:     0 required (???)
+# bit8:     1, add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9:     0, no half clock cycle addition to dataout
+# bit10:    0, 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11:    0, 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 0xf required
+# bit31-16: 0 required
+
+# DDR2 ODT Read Timing (default values)
+DATA 0xFFD01428 0x00085520
+# bit3-0:   0 required
+# bit7-4:   2, 2 cycles from read command to assertion of M_ODT signal
+# bit11-8:  5, 5 cycles from read command to de-assertion of M_ODT signal
+# bit15-12: 5, 5 cycles from read command to assertion of internal ODT signal
+# bit19-16: 8, 8 cycles from read command to de-assertion of internal ODT signal
+# bit31-20: 0 required
+
+# DDR2 ODT Write Timing (default values)
+DATA 0xFFD0147C 0x00008552
+# bit3-0:   2, 2 cycles from write comand to assertion of M_ODT signal
+# bit7-4:   5, 5 cycles from write command to de-assertion of M_ODT signal
+# bit15-12: 5, 5 cycles from write command to assertion of internal ODT signal
+# bit19-16: 8, 8 cycles from write command to de-assertion of internal ODT signal
+# bit31-16: 0 required
+
+# CS[0]n Base address
+DATA 0xFFD01500 0x00000000
+# at 0x0
+
+# CS[0]n Size
+DATA 0xFFD01504 0x0FFFFFF1
+# bit0:     1, Window enabled
+# bit1:     0, Write Protect disabled
+# bit3-2:   0x0, CS0 hit selected
+# bit23-4:  0xfffff required
+# bit31-24: 0x0f, Size (i.e. 256MB)
+
+# CS[1]n Size
+DATA 0xFFD0150C 0x00000000
+# window disabled
+
+# CS[2]n Size
+DATA 0xFFD01514 0x00000000
+# window disabled
+
+# CS[3]n Size
+DATA 0xFFD0151C 0x00000000
+# window disabled
+
+# DDR ODT Control (Low)
+DATA 0xFFD01494 0x00010000
+# bit3-0:   0b0000, (read) M_ODT[0] is not asserted during read from DRAM
+# bit7-4:   0b0000, (read) M_ODT[1] is not asserted during read from DRAM
+# bit15-8:  0 required
+# bit19-16: 0b0001, (write) M_ODT[0] is asserted during write to DRAM CS0
+# bit23-20: 0b0000, (write) M_ODT[1] is not asserted during write to DRAM
+# bit31-24: 0 required
+
+# DDR ODT Control (High)
+DATA 0xFFD01498 0x00000000
+# bit1-0:   0, M_ODT[0] assertion is controlled by ODT Control Low register
+# bit3-2:   0, M_ODT[1] assertion is controlled by ODT Control Low register
+# bit31-4   0 required
+
+# CPU ODT Control
+DATA 0xFFD0149C 0x0000E80F
+# bit3-0:   0b1111, internal ODT is asserted during read from DRAM bank 0-3
+# bit7-4:   0b0000, internal ODT is not asserted during write to DRAM bank 0-3
+# bit9-8:   0, Internal ODT assertion is controlled by fiels
+# bit11-10: 2, M_DQ, M_DM, and M_DQS I/O buffer ODT 75 ohm
+# bit13-12: 2, M_STARTBURST_IN I/O buffer ODT 75 ohm
+# bit14:    1, M_STARTBURST_IN ODT enabled
+# bit15:    1, DDR IO ODT Unit: Drive ODT calibration values
+# bit20-16: 0, Pad N channel driving strength for ODT
+# bit25-21: 0, Pad P channel driving strength for ODT
+# bit31-26: 0 required
+
+# DDR Initialization Control
+DATA 0xFFD01480 0x00000001
+# bit0:     1, enable DDR init upon this register write
+# bit31-1:  0, required
+
+# End of Header extension
+DATA 0x0 0x0