Adding Support for BAV335x boards

8 files changed, 883 insertions, 0 deletions

diff --git a/board/birdland/bav335x/Kconfig b/board/birdland/bav335x/Kconfig
new file mode 100644
index 0000000..3380ed3
--- /dev/null
+++ b/board/birdland/bav335x/Kconfig
@@ -0,0 +1,33 @@
+if TARGET_BAV335X
+
+config SYS_BOARD
+	default "bav335x"
+
+config SYS_VENDOR
+	default "birdland"
+
+config SYS_SOC
+	default "am33xx"
+
+config SYS_CONFIG_NAME
+	default "bav335x"
+
+config CONS_INDEX
+	int "UART used for console"
+	range 1 6
+	default 1
+	help
+	  The AM335x SoC has a total of 6 UARTs (UART0 to UART5 as referenced
+	  in documentation, etc) available to it.  Depending on your specific
+	  board you may want something other than UART0 as for example the IDK
+	  uses UART3 so enter 4 here.
+
+config BAV_VERSION
+	int "BAV335x Version (1=A, 2=B)"
+	range 1 2
+	help
+	  The BAV335x has various version of the board. Rev.A (mostly obsolete)
+	  used 10/100 Ethernet PHY while Rev.B uses a Gigabit Ethernet PHY.
+	  Overwrite this if you have an older Rev.A and want ethernet support.
+
+endif
diff --git a/board/birdland/bav335x/MAINTAINERS b/board/birdland/bav335x/MAINTAINERS
new file mode 100644
index 0000000..45dcfcb
--- /dev/null
+++ b/board/birdland/bav335x/MAINTAINERS
@@ -0,0 +1,13 @@
+BAV335x BOARD
+M:	Gilles Gameiro <gilles@gigadevices.com>
+S:	Maintained
+F:	include/configs/bav335x.h
+F:	board/birdland/bav335x/Kconfig
+F:	board/birdland/bav335x/Makefile
+F:	board/birdland/bav335x/README
+F:	board/birdland/bav335x/board.c
+F:	board/birdland/bav335x/board.h
+F:	board/birdland/bav335x/mux.c
+F:	board/birdland/bav335x/u-boot.lds
+F:	configs/birdland_bav335a_defconfig
+F:	configs/birdland_bav335b_defconfig
diff --git a/board/birdland/bav335x/Makefile b/board/birdland/bav335x/Makefile
new file mode 100644
index 0000000..2fc5614
--- /dev/null
+++ b/board/birdland/bav335x/Makefile
@@ -0,0 +1,11 @@
+#
+# Makefile
+#
+# Copyright (C) 2012-2014, Birdland Audio - http://birdland.com/oem
+#
+
+ifeq ($(CONFIG_SKIP_LOWLEVEL_INIT),)
+obj-y	:= mux.o
+endif
+
+obj-y	+= board.o
diff --git a/board/birdland/bav335x/README b/board/birdland/bav335x/README
new file mode 100644
index 0000000..08c73ee
--- /dev/null
+++ b/board/birdland/bav335x/README
@@ -0,0 +1,31 @@
+Summary
+=======
+
+This document covers various features of the 'BAV335x' board build.
+For more information about this board, visit http://birdland.com/oem
+
+
+Hardware
+========
+
+The binary produced supports the bav335x Rev.A with 10/100 MB PHY
+and Rev.B (default) with GB ethernet PHY.
+If the BAV335x EEPROM is populated and programmed, the board will
+automatically detect the version and extract proper serial# and
+mac address from the EE.
+
+
+Customization
+=============
+
+The following blocks are required:
+- I2C, to talk with the PMIC and ensure that we do not run afoul of
+  errata 1.0.24.
+
+When removing options as part of customization,
+CONFIG_EXTRA_ENV_SETTINGS will need additional care to update for your
+needs and to remove no longer relevant options as in some cases we
+define additional text blocks (such as for NAND or DFU strings).  Also
+note that all of the SPL options are grouped together, rather than with
+the IP blocks, so both areas will need their choices updated to reflect
+the custom design.
diff --git a/board/birdland/bav335x/board.c b/board/birdland/bav335x/board.c
new file mode 100644
index 0000000..d1e1c8c
--- /dev/null
+++ b/board/birdland/bav335x/board.c
@@ -0,0 +1,430 @@
+/*
+ * board.c
+ *
+ * Board functions for Birdland Audio BAV335x Network Processor
+ *
+ * Copyright (c) 2012-2014 Birdland Audio - http://birdland.com/oem
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include <power/tps65217.h>
+#include <power/tps65910.h>
+#include <environment.h>
+#include <watchdog.h>
+#include <environment.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* GPIO that controls power to DDR on EVM-SK */
+#define GPIO_DDR_VTT_EN		7
+
+static __maybe_unused struct ctrl_dev *cdev =
+		(struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+
+
+/*
+ * Read header information from EEPROM into global structure.
+ */
+static int read_eeprom(struct board_eeconfig *header)
+{
+	/* Check if baseboard eeprom is available */
+	if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR))
+		return -ENODEV;
+
+	/* read the eeprom using i2c */
+	if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header,
+		     sizeof(struct board_eeconfig)))
+		return -EIO;
+
+	if (header->magic != BOARD_MAGIC) {
+		/* read the i2c eeprom again using only a 1 byte address */
+		if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
+			     sizeof(struct board_eeconfig)))
+			return -EIO;
+
+		if (header->magic != BOARD_MAGIC)
+			return -EINVAL;
+	}
+	return 0;
+}
+
+
+
+
+enum board_type get_board_type(bool debug)
+{
+	int ecode;
+	struct board_eeconfig header;
+
+	ecode = read_eeprom(&header);
+	if (ecode == 0) {
+		if (header.version[1] == 'A') {
+			if (debug)
+				puts("=== Detected Board model BAV335x Rev.A");
+			return BAV335A;
+		} else if (header.version[1] == 'B') {
+			if (debug)
+				puts("=== Detected Board model BAV335x Rev.B");
+			return BAV335B;
+		} else if (debug) {
+			puts("### Un-known board model in serial-EE\n");
+		}
+	} else if (debug) {
+		switch (ecode) {
+		case -ENODEV:
+			puts("### Board doesn't have a serial-EE\n");
+			break;
+		case -EINVAL:
+			puts("### Board serial-EE signature is incorrect.\n");
+			break;
+		default:
+			puts("### IO Error reading serial-EE.\n");
+			break;
+		}
+	}
+
+#if (CONFIG_BAV_VERSION == 1)
+	if (debug)
+		puts("### Selecting BAV335A as per config\n");
+	return BAV335A;
+#elif (CONFIG_BAV_VERSION == 2)
+	if (debug)
+		puts("### Selecting BAV335B as per config\n");
+	return BAV335B;
+#endif
+#if (NOT_DEFINED == 2)
+#error "SHOULD NEVER DISPLAY THIS"
+#endif
+
+	if (debug)
+		puts("### Defaulting to model BAV335x Rev.B\n");
+	return BAV335B;
+}
+
+
+
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+static const struct ddr_data ddr3_bav335x_data = {
+	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
+	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_bav335x_cmd_ctrl_data = {
+	.cmd0csratio = MT41K256M16HA125E_RATIO,
+	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+	.cmd1csratio = MT41K256M16HA125E_RATIO,
+	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+	.cmd2csratio = MT41K256M16HA125E_RATIO,
+	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+
+static struct emif_regs ddr3_bav335x_emif_reg_data = {
+	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+	.zq_config = MT41K256M16HA125E_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+	/* break into full u-boot on 'c' */
+	if (serial_tstc() && serial_getc() == 'c')
+		return 1;
+
+#ifdef CONFIG_SPL_ENV_SUPPORT
+	env_init();
+	env_relocate_spec();
+	if (getenv_yesno("boot_os") != 1)
+		return 1;
+#endif
+
+	return 0;
+}
+#endif
+
+#define OSC	(V_OSCK/1000000)
+const struct dpll_params dpll_ddr = {
+		266, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_evm_sk = {
+		303, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_bone_black = {
+		400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+	/* debug print detect status */
+	(void)get_board_type(true);
+
+	/* Get the frequency */
+	/* dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); */
+	dpll_mpu_opp100.m = MPUPLL_M_1000;
+
+	if (i2c_probe(TPS65217_CHIP_PM))
+		return;
+
+	/* Set the USB Current Limit */
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
+			       TPS65217_USB_INPUT_CUR_LIMIT_1800MA,
+			       TPS65217_USB_INPUT_CUR_LIMIT_MASK))
+		puts("! tps65217_reg_write: could not set USB limit\n");
+
+	/* Set the Core Voltage (DCDC3) to 1.125V */
+	if (tps65217_voltage_update(TPS65217_DEFDCDC3,
+				    TPS65217_DCDC_VOLT_SEL_1125MV)) {
+		puts("! tps65217_reg_write: could not set Core Voltage\n");
+		return;
+	}
+
+	/* Set CORE Frequencies to OPP100 */
+	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+	/* Set the MPU Voltage (DCDC2) */
+	if (tps65217_voltage_update(TPS65217_DEFDCDC2,
+				    TPS65217_DCDC_VOLT_SEL_1325MV)) {
+		puts("! tps65217_reg_write: could not set MPU Voltage\n");
+		return;
+	}
+
+	/*
+	 * Set LDO3, LDO4 output voltage to 3.3V for Beaglebone.
+	 * Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black.
+	 */
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS1,
+			       TPS65217_LDO_VOLTAGE_OUT_1_8, TPS65217_LDO_MASK))
+		puts("! tps65217_reg_write: could not set LDO3\n");
+
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS2,
+			       TPS65217_LDO_VOLTAGE_OUT_3_3, TPS65217_LDO_MASK))
+		puts("! tps65217_reg_write: could not set LDO4\n");
+
+	/* Set MPU Frequency to what we detected now that voltages are set */
+	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	enable_i2c0_pin_mux();
+	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+	return &dpll_ddr_bone_black;
+}
+
+void set_uart_mux_conf(void)
+{
+#if CONFIG_CONS_INDEX == 1
+	enable_uart0_pin_mux();
+#elif CONFIG_CONS_INDEX == 2
+	enable_uart1_pin_mux();
+#elif CONFIG_CONS_INDEX == 3
+	enable_uart2_pin_mux();
+#elif CONFIG_CONS_INDEX == 4
+	enable_uart3_pin_mux();
+#elif CONFIG_CONS_INDEX == 5
+	enable_uart4_pin_mux();
+#elif CONFIG_CONS_INDEX == 6
+	enable_uart5_pin_mux();
+#endif
+}
+
+void set_mux_conf_regs(void)
+{
+	enum board_type board;
+
+	board = get_board_type(false);
+	enable_board_pin_mux(board);
+}
+
+const struct ctrl_ioregs ioregs_bonelt = {
+	.cm0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm2ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+
+void sdram_init(void)
+{
+	config_ddr(400, &ioregs_bonelt,
+		   &ddr3_bav335x_data,
+		   &ddr3_bav335x_cmd_ctrl_data,
+		   &ddr3_bav335x_emif_reg_data, 0);
+}
+#endif
+
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+#if defined(CONFIG_HW_WATCHDOG)
+	hw_watchdog_init();
+#endif
+
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+#if defined(CONFIG_NOR) || defined(CONFIG_NAND)
+	gpmc_init();
+#endif
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	setenv("board_name", "BAV335xB");
+	setenv("board_rev", "B"); /* Fix me, but why bother.. */
+#endif
+	return 0;
+}
+#endif
+
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_addr	= 0,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_addr	= 1,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs	= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs	= 0xd00,
+	.ale_entries	= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
+	.mac_control	= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num	= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+#endif
+
+
+/*
+ * This function will:
+ * Perform fixups to the PHY present on certain boards.  We only need this
+ * function in:
+ * - SPL with either CPSW or USB ethernet support
+ * - Full U-Boot, with either CPSW or USB ethernet
+ * Build in only these cases to avoid warnings about unused variables
+ * when we build an SPL that has neither option but full U-Boot will.
+ */
+#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) &&\
+		defined(CONFIG_SPL_BUILD)) || \
+	((defined(CONFIG_DRIVER_TI_CPSW) || \
+	  defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) && \
+	 !defined(CONFIG_SPL_BUILD))
+int board_eth_init(bd_t *bis)
+{
+	int ecode, rv, n;
+	uint8_t mac_addr[6];
+	struct board_eeconfig header;
+	__maybe_unused enum board_type board;
+
+	/* Default manufacturing address; used when no EE or invalid */
+	n = 0;
+	mac_addr[0] = 0;
+	mac_addr[1] = 0x20;
+	mac_addr[2] = 0x18;
+	mac_addr[3] = 0x1C;
+	mac_addr[4] = 0x00;
+	mac_addr[5] = 0x01;
+
+	ecode = read_eeprom(&header);
+	/* if we have a valid EE, get mac address from there */
+	if ((ecode == 0) &&
+	    is_valid_ether_addr((const u8 *)&header.mac_addr[0][0])) {
+		memcpy(mac_addr, (const void *)&header.mac_addr[0][0], 6);
+	}
+
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+
+	if (!getenv("ethaddr")) {
+		printf("<ethaddr> not set. Validating first E-fuse MAC\n");
+
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+	}
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+
+	board = get_board_type(false);
+
+	/* Rev.A uses 10/100 PHY in mii mode */
+	if (board == BAV335A) {
+		writel(MII_MODE_ENABLE, &cdev->miisel);
+		cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
+		cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII;
+	}
+	/* Rev.B (default) uses GB PHY in rmii mode */
+	else {
+		writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel);
+		cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if
+				= PHY_INTERFACE_MODE_RGMII;
+	}
+
+	rv = cpsw_register(&cpsw_data);
+	if (rv < 0)
+		printf("Error %d registering CPSW switch\n", rv);
+	else
+		n += rv;
+#endif
+
+#endif
+
+	return n;
+}
+#endif
diff --git a/board/birdland/bav335x/board.h b/board/birdland/bav335x/board.h
new file mode 100644
index 0000000..b598ce1
--- /dev/null
+++ b/board/birdland/bav335x/board.h
@@ -0,0 +1,59 @@
+/*
+ * board.c
+ *
+ * Board functions for Birdland Audio BAV335x Network Processor
+ *
+ * Copyright (c) 2012-2014, Birdland Audio - http://birdland.com/oem
+ *
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/* Serial MagicE: AA 55 BA BE */
+#define BOARD_MAGIC  0xBEBA55AA
+enum board_type {UNKNOWN, BAV335A, BAV335B};
+
+
+/*
+ * The BAV335x may use a built-in read-only serial EEProm.
+ * The Evaluation board, disables the write-protect so the Serial-EE
+ * Can be programmed during manufacturing to store fields such as
+ * a board serial number, ethernet mac address and other user fields.
+ * Additionally, the Serial-EE can store the specific version of the
+ * board it runs on, and overwrite the defaults in _defconfig
+ */
+#define HDR_NO_OF_MAC_ADDR	3
+#define HDR_ETH_ALEN		6
+#define HDR_NAME_LEN		8
+
+struct board_eeconfig {
+	unsigned int  magic;
+	char name[HDR_NAME_LEN];	/* BAV3354 */
+	char version[4];		/* 0B20 - Rev.B2 */
+	char serial[12];
+	char config[32];
+	char mac_addr[HDR_NO_OF_MAC_ADDR][HDR_ETH_ALEN];
+};
+
+enum board_type get_board_type(bool verbose_debug_output);
+
+
+/*
+ * We have three pin mux functions that must exist.  We must be able to enable
+ * uart0, for initial output and i2c0 to read the main EEPROM.  We then have a
+ * main pinmux function that can be overridden to enable all other pinmux that
+ * is required on the board.
+ */
+void enable_uart0_pin_mux(void);
+void enable_uart1_pin_mux(void);
+void enable_uart2_pin_mux(void);
+void enable_uart3_pin_mux(void);
+void enable_uart4_pin_mux(void);
+void enable_uart5_pin_mux(void);
+void enable_i2c0_pin_mux(void);
+void enable_board_pin_mux(enum board_type board);
+
+#endif
diff --git a/board/birdland/bav335x/mux.c b/board/birdland/bav335x/mux.c
new file mode 100644
index 0000000..f18bfa4
--- /dev/null
+++ b/board/birdland/bav335x/mux.c
@@ -0,0 +1,190 @@
+/*
+ * mux.c
+ *
+ * Copyright (c) 2012-2014 Birdland Audio - http://birdland.com/oem
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include "board.h"
+
+static struct module_pin_mux uart0_pin_mux[] = {
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* UART0_RXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},		/* UART0_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart1_pin_mux[] = {
+	{OFFSET(uart1_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* UART1_RXD */
+	{OFFSET(uart1_txd), (MODE(0) | PULLUDEN)},		/* UART1_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart2_pin_mux[] = {
+	{OFFSET(spi0_sclk), (MODE(1) | PULLUP_EN | RXACTIVE)},	/* UART2_RXD */
+	{OFFSET(spi0_d0), (MODE(1) | PULLUDEN)},		/* UART2_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart3_pin_mux[] = {
+	{OFFSET(spi0_cs1), (MODE(1) | PULLUP_EN | RXACTIVE)},	/* UART3_RXD */
+	{OFFSET(ecap0_in_pwm0_out), (MODE(1) | PULLUDEN)},	/* UART3_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart4_pin_mux[] = {
+	{OFFSET(gpmc_wait0), (MODE(6) | PULLUP_EN | RXACTIVE)},	/* UART4_RXD */
+	{OFFSET(gpmc_wpn), (MODE(6) | PULLUDEN)},		/* UART4_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart5_pin_mux[] = {
+	{OFFSET(lcd_data9), (MODE(4) | PULLUP_EN | RXACTIVE)},	/* UART5_RXD */
+	{OFFSET(lcd_data8), (MODE(4) | PULLUDEN)},		/* UART5_TXD */
+	{-1},
+};
+
+static struct module_pin_mux mmc0_pin_mux[] = {
+	{OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT3 */
+	{OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT2 */
+	{OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT1 */
+	{OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT0 */
+	{OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CLK */
+	{OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CMD */
+	{OFFSET(mcasp0_aclkr), (MODE(4) | RXACTIVE)},		/* MMC0_WP */
+	{OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)},	/* MMC0_CD */
+	{-1},
+};
+
+static struct module_pin_mux mmc1_pin_mux[] = {
+	{OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT3 */
+	{OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT2 */
+	{OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT1 */
+	{OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT0 */
+	{OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CLK */
+	{OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CMD */
+	{OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)},	/* MMC1_WP */
+	{OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
+	{-1},
+};
+
+static struct module_pin_mux i2c0_pin_mux[] = {
+	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
+			PULLUDEN | SLEWCTRL)}, /* I2C_DATA */
+	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
+			PULLUDEN | SLEWCTRL)}, /* I2C_SCLK */
+	{-1},
+};
+
+static struct module_pin_mux i2c1_pin_mux[] = {
+	{OFFSET(spi0_d1), (MODE(2) | RXACTIVE |
+			PULLUDEN | SLEWCTRL)},	/* I2C_DATA */
+	{OFFSET(spi0_cs0), (MODE(2) | RXACTIVE |
+			PULLUDEN | SLEWCTRL)},	/* I2C_SCLK */
+	{-1},
+};
+
+static struct module_pin_mux rgmii1_pin_mux[] = {
+	{OFFSET(mii1_txen), MODE(2)},			/* RGMII1_TCTL */
+	{OFFSET(mii1_rxdv), MODE(2) | RXACTIVE},	/* RGMII1_RCTL */
+	{OFFSET(mii1_txd3), MODE(2)},			/* RGMII1_TD3 */
+	{OFFSET(mii1_txd2), MODE(2)},			/* RGMII1_TD2 */
+	{OFFSET(mii1_txd1), MODE(2)},			/* RGMII1_TD1 */
+	{OFFSET(mii1_txd0), MODE(2)},			/* RGMII1_TD0 */
+	{OFFSET(mii1_txclk), MODE(2)},			/* RGMII1_TCLK */
+	{OFFSET(mii1_rxclk), MODE(2) | RXACTIVE},	/* RGMII1_RCLK */
+	{OFFSET(mii1_rxd3), MODE(2) | RXACTIVE},	/* RGMII1_RD3 */
+	{OFFSET(mii1_rxd2), MODE(2) | RXACTIVE},	/* RGMII1_RD2 */
+	{OFFSET(mii1_rxd1), MODE(2) | RXACTIVE},	/* RGMII1_RD1 */
+	{OFFSET(mii1_rxd0), MODE(2) | RXACTIVE},	/* RGMII1_RD0 */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+static struct module_pin_mux mii1_pin_mux[] = {
+	{OFFSET(mii1_rxerr), MODE(0) | RXACTIVE},	/* MII1_RXERR */
+	{OFFSET(mii1_txen), MODE(0)},			/* MII1_TXEN */
+	{OFFSET(mii1_rxdv), MODE(0) | RXACTIVE},	/* MII1_RXDV */
+	{OFFSET(mii1_txd3), MODE(0)},			/* MII1_TXD3 */
+	{OFFSET(mii1_txd2), MODE(0)},			/* MII1_TXD2 */
+	{OFFSET(mii1_txd1), MODE(0)},			/* MII1_TXD1 */
+	{OFFSET(mii1_txd0), MODE(0)},			/* MII1_TXD0 */
+	{OFFSET(mii1_txclk), MODE(0) | RXACTIVE},	/* MII1_TXCLK */
+	{OFFSET(mii1_rxclk), MODE(0) | RXACTIVE},	/* MII1_RXCLK */
+	{OFFSET(mii1_rxd3), MODE(0) | RXACTIVE},	/* MII1_RXD3 */
+	{OFFSET(mii1_rxd2), MODE(0) | RXACTIVE},	/* MII1_RXD2 */
+	{OFFSET(mii1_rxd1), MODE(0) | RXACTIVE},	/* MII1_RXD1 */
+	{OFFSET(mii1_rxd0), MODE(0) | RXACTIVE},	/* MII1_RXD0 */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_uart1_pin_mux(void)
+{
+	configure_module_pin_mux(uart1_pin_mux);
+}
+
+void enable_uart2_pin_mux(void)
+{
+	configure_module_pin_mux(uart2_pin_mux);
+}
+
+void enable_uart3_pin_mux(void)
+{
+	configure_module_pin_mux(uart3_pin_mux);
+}
+
+void enable_uart4_pin_mux(void)
+{
+	configure_module_pin_mux(uart4_pin_mux);
+}
+
+void enable_uart5_pin_mux(void)
+{
+	configure_module_pin_mux(uart5_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+}
+
+
+/* CPLD registers */
+#define I2C_CPLD_ADDR	0x35
+#define CFG_REG		0x10
+
+
+void enable_board_pin_mux(enum board_type board)
+{
+	configure_module_pin_mux(i2c1_pin_mux);
+	if (board == BAV335A)
+		configure_module_pin_mux(mii1_pin_mux); /* MII Mode: 10/100MB */
+	else
+		configure_module_pin_mux(rgmii1_pin_mux); /* RGMII Mode: GB */
+
+	configure_module_pin_mux(mmc0_pin_mux);
+	configure_module_pin_mux(mmc1_pin_mux);
+}
diff --git a/board/birdland/bav335x/u-boot.lds b/board/birdland/bav335x/u-boot.lds
new file mode 100644
index 0000000..fc80f21
--- /dev/null
+++ b/board/birdland/bav335x/u-boot.lds
@@ -0,0 +1,116 @@
+/*
+ * Copyright (c) 2012-2014 Birdland Audio - http://birdland.com/oem
+ * Copyright (c) 2004-2008 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text :
+	{
+		*(.__image_copy_start)
+		*(.vectors)
+		CPUDIR/start.o (.text*)
+		board/birdland/bav335x/built-in.o (.text*)
+		*(.text*)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+	. = ALIGN(4);
+	.data : {
+		*(.data*)
+	}
+
+	. = ALIGN(4);
+
+	. = .;
+
+	. = ALIGN(4);
+	.u_boot_list : {
+		KEEP(*(SORT(.u_boot_list*)));
+	}
+
+	. = ALIGN(4);
+
+	.image_copy_end :
+	{
+		*(.__image_copy_end)
+	}
+
+	.rel_dyn_start :
+	{
+		*(.__rel_dyn_start)
+	}
+
+	.rel.dyn : {
+		*(.rel*)
+	}
+
+	.rel_dyn_end :
+	{
+		*(.__rel_dyn_end)
+	}
+
+	.hash : { *(.hash*) }
+
+	.end :
+	{
+		*(.__end)
+	}
+
+	_image_binary_end = .;
+
+	/*
+	 * Deprecated: this MMU section is used by pxa at present but
+	 * should not be used by new boards/CPUs.
+	 */
+	. = ALIGN(4096);
+	.mmutable : {
+		*(.mmutable)
+	}
+
+/*
+ * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
+ * __bss_base and __bss_limit are for linker only (overlay ordering)
+ */
+
+	.bss_start __rel_dyn_start (OVERLAY) : {
+		KEEP(*(.__bss_start));
+		__bss_base = .;
+	}
+
+	.bss __bss_base (OVERLAY) : {
+		*(.bss*)
+		 . = ALIGN(4);
+		 __bss_limit = .;
+	}
+
+	.bss_end __bss_limit (OVERLAY) : {
+		KEEP(*(.__bss_end));
+	}
+
+	.dynsym _image_binary_end : { *(.dynsym) }
+	.dynbss : { *(.dynbss) }
+	.dynstr : { *(.dynstr*) }
+	.dynamic : { *(.dynamic*) }
+	.gnu.hash : { *(.gnu.hash) }
+	.plt : { *(.plt*) }
+	.interp : { *(.interp*) }
+	.gnu : { *(.gnu*) }
+	.ARM.exidx : { *(.ARM.exidx*) }
+}