ppc4xx: Remove AP1000 board support

As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>

1 files changed, 0 insertions, 704 deletions

diff --git a/board/amirix/ap1000/ap1000.c b/board/amirix/ap1000/ap1000.c
deleted file mode 100644
index dbcb34b..0000000
--- a/board/amirix/ap1000/ap1000.c
+++ /dev/null
@@ -1,704 +0,0 @@
-/*
- * amirix.c: ppcboot platform support for AMIRIX board
- *
- * Copyright 2002 Mind NV
- * Copyright 2003 AMIRIX Systems Inc.
- *
- * http://www.mind.be/
- * http://www.amirix.com/
- *
- * Author : Peter De Schrijver (p2@mind.be)
- *          Frank Smith (smith@amirix.com)
- *
- * Derived from : Other platform support files in this tree, ml2
- *
- * This software may be used and distributed according to the terms of
- * the GNU General Public License (GPL) version 2, incorporated herein by
- * reference. Drivers based on or derived from this code fall under the GPL
- * and must retain the authorship, copyright and this license notice. This
- * file is not a complete program and may only be used when the entire
- * program is licensed under the GPL.
- *
- */
-
-#include <common.h>
-#include <command.h>
-#include <netdev.h>
-#include <asm/processor.h>
-
-#include "powerspan.h"
-#include "ap1000.h"
-
-int board_pre_init (void)
-{
-	return 0;
-}
-
-/** serial number and platform display at startup */
-int checkboard (void)
-{
-	char buf[64];
-	int l = getenv_f("serial#", buf, sizeof(buf));
-
-	/* After a loadace command, the SystemAce control register is left in a wonky state. */
-	/* this code did not work in board_pre_init */
-	unsigned char *p = (unsigned char *) AP1000_SYSACE_REGBASE;
-	unsigned int *revision_reg_ptr = (unsigned int *) AP1xx_FPGA_REV_ADDR;
-	unsigned int device = (*revision_reg_ptr & AP1xx_TARGET_MASK);
-
-	p[SYSACE_CTRLREG0] = 0x0;
-
-	/* add platform and device to banner */
-	switch (device) {
-	case AP1xx_AP107_TARGET:
-		puts (AP1xx_AP107_TARGET_STR);
-		break;
-	case AP1xx_AP120_TARGET:
-		puts (AP1xx_AP120_TARGET_STR);
-		break;
-	case AP1xx_AP130_TARGET:
-		puts (AP1xx_AP130_TARGET_STR);
-		break;
-	case AP1xx_AP1070_TARGET:
-		puts (AP1xx_AP1070_TARGET_STR);
-		break;
-	case AP1xx_AP1100_TARGET:
-		puts (AP1xx_AP1100_TARGET_STR);
-		break;
-	default:
-		puts (AP1xx_UNKNOWN_STR);
-		break;
-	}
-	puts (AP1xx_TARGET_STR);
-	puts (" with ");
-
-	switch (get_platform ()) {
-	case AP100_BASELINE_PLATFORM:
-	case AP1000_BASELINE_PLATFORM:
-		puts (AP1xx_BASELINE_PLATFORM_STR);
-		break;
-	case AP1xx_QUADGE_PLATFORM:
-		puts (AP1xx_QUADGE_PLATFORM_STR);
-		break;
-	case AP1xx_MGT_REF_PLATFORM:
-		puts (AP1xx_MGT_REF_PLATFORM_STR);
-		break;
-	case AP1xx_STANDARD_PLATFORM:
-		puts (AP1xx_STANDARD_PLATFORM_STR);
-		break;
-	case AP1xx_DUAL_PLATFORM:
-		puts (AP1xx_DUAL_PLATFORM_STR);
-		break;
-	case AP1xx_BASE_SRAM_PLATFORM:
-		puts (AP1xx_BASE_SRAM_PLATFORM_STR);
-		break;
-	case AP1xx_PCI_PCB_TESTPLATFORM:
-	case AP1000_PCI_PCB_TESTPLATFORM:
-		puts (AP1xx_PCI_PCB_TESTPLATFORM_STR);
-		break;
-	case AP1xx_DUAL_GE_MEZZ_TESTPLATFORM:
-		puts (AP1xx_DUAL_GE_MEZZ_TESTPLATFORM_STR);
-		break;
-	case AP1xx_SFP_MEZZ_TESTPLATFORM:
-		puts (AP1xx_SFP_MEZZ_TESTPLATFORM_STR);
-		break;
-	default:
-		puts (AP1xx_UNKNOWN_STR);
-		break;
-	}
-
-	if ((get_platform () & AP1xx_TESTPLATFORM_MASK) != 0) {
-		puts (AP1xx_TESTPLATFORM_STR);
-	} else {
-		puts (AP1xx_PLATFORM_STR);
-	}
-
-	putc ('\n');
-
-	puts ("Serial#: ");
-
-	if (l < 0) {
-		printf ("### No HW ID - assuming AMIRIX");
-	} else {
-		int i;
-
-		for (i = 0; i < l; ++i) {
-			if (buf[i] == ' ') {
-				buf[i] = '\0';
-				break;
-			}
-		}
-
-		puts(buf);
-	}
-
-	putc ('\n');
-
-	return (0);
-}
-
-
-phys_size_t initdram (int board_type)
-{
-	char buf[64];
-	int i = getenv_f("dramsize", buf, sizeof(buf));
-
-	if (i > 0) {
-		char *s = buf;
-		if ((s[0] == '0') && ((s[1] == 'x') || (s[1] == 'X'))) {
-			s += 2;
-		}
-		return (long int)simple_strtoul (s, NULL, 16);
-	} else {
-		/* give all 64 MB */
-		return 64 * 1024 * 1024;
-	}
-}
-
-unsigned int get_platform (void)
-{
-	unsigned int *revision_reg_ptr = (unsigned int *) AP1xx_FPGA_REV_ADDR;
-
-	return (*revision_reg_ptr & AP1xx_PLATFORM_MASK);
-}
-
-#if 0				/* loadace is not working; it appears to be a hardware issue with the system ace. */
-/*
-   This function loads FPGA configurations from the SystemACE CompactFlash
-*/
-int do_loadace (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	unsigned char *p = (unsigned char *) AP1000_SYSACE_REGBASE;
-	int cfg;
-
-	if ((p[SYSACE_STATREG0] & 0x10) == 0) {
-		p[SYSACE_CTRLREG0] = 0x80;
-		printf ("\nNo CompactFlash Detected\n\n");
-		p[SYSACE_CTRLREG0] = 0x00;
-		return 1;
-	}
-
-	/* reset configuration controller: |  0x80 */
-	/* select cpflash                  & ~0x40 */
-	/* cfg start                       |  0x20 */
-	/* wait for cfgstart               & ~0x10 */
-	/* force cfgmode:                  |  0x08 */
-	/* do no force cfgaddr:            & ~0x04 */
-	/* clear mpulock:                  & ~0x02 */
-	/* do not force lock request       & ~0x01 */
-
-	p[SYSACE_CTRLREG0] = 0x80 | 0x20 | 0x08;
-	p[SYSACE_CTRLREG1] = 0x00;
-
-	/* force config address if arg2 exists */
-	if (argc == 2) {
-		cfg = simple_strtoul (argv[1], NULL, 10);
-
-		if (cfg > 7) {
-			printf ("\nInvalid Configuration\n\n");
-			p[SYSACE_CTRLREG0] = 0x00;
-			return 1;
-		}
-		/* Set config address */
-		p[SYSACE_CTRLREG1] = (cfg << 5);
-		/* force cfgaddr */
-		p[SYSACE_CTRLREG0] |= 0x04;
-
-	} else {
-		cfg = (p[SYSACE_STATREG1] & 0xE0) >> 5;
-	}
-
-	/* release configuration controller */
-	printf ("\nLoading V2PRO with config %d...\n", cfg);
-	p[SYSACE_CTRLREG0] &= ~0x80;
-
-
-	while ((p[SYSACE_STATREG1] & 0x01) == 0) {
-
-		if (p[SYSACE_ERRREG0] & 0x80) {
-			/* attempting to load an invalid configuration makes the cpflash */
-			/* appear to be removed. Reset here to avoid that problem */
-			p[SYSACE_CTRLREG0] = 0x80;
-			printf ("\nConfiguration %d Read Error\n\n", cfg);
-			p[SYSACE_CTRLREG0] = 0x00;
-			return 1;
-		}
-	}
-
-	p[SYSACE_CTRLREG0] |= 0x20;
-
-	return 0;
-}
-#endif
-
-/** Console command to display and set the software reconfigure byte
-  * <pre>
-  * swconfig        - display the current value of the software reconfigure byte
-  * swconfig [#]    - change the software reconfigure byte to #
-  * </pre>
-  * @param  *cmdtp  [IN] as passed by run_command (ignored)
-  * @param  flag    [IN] as passed by run_command (ignored)
-  * @param  argc    [IN] as passed by run_command if 1, display, if 2 change
-  * @param  *argv[] [IN] contains the parameters to use
-  * @return
-  * <pre>
-  *      0 if passed
-  *     -1 if failed
-  * </pre>
-  */
-int do_swconfigbyte (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	unsigned char *sector_buffer = NULL;
-	unsigned char input_char;
-	int write_result;
-	unsigned int input_uint;
-
-	/* display value if no argument */
-	if (argc < 2) {
-		printf ("Software configuration byte is currently: 0x%02x\n",
-			*((unsigned char *) (SW_BYTE_SECTOR_ADDR +
-					     SW_BYTE_SECTOR_OFFSET)));
-		return 0;
-	} else if (argc > 3) {
-		printf ("Too many arguments\n");
-		return -1;
-	}
-
-	/* if 3 arguments, 3rd argument is the address to use */
-	if (argc == 3) {
-		input_uint = simple_strtoul (argv[1], NULL, 16);
-		sector_buffer = (unsigned char *) input_uint;
-	} else {
-		sector_buffer = (unsigned char *) DEFAULT_TEMP_ADDR;
-	}
-
-	input_char = simple_strtoul (argv[1], NULL, 0);
-	if ((input_char & ~SW_BYTE_MASK) != 0) {
-		printf ("Input of 0x%02x will be masked to 0x%02x\n",
-			input_char, (input_char & SW_BYTE_MASK));
-		input_char = input_char & SW_BYTE_MASK;
-	}
-
-	memcpy (sector_buffer, (void *) SW_BYTE_SECTOR_ADDR,
-		SW_BYTE_SECTOR_SIZE);
-	sector_buffer[SW_BYTE_SECTOR_OFFSET] = input_char;
-
-
-	printf ("Erasing Flash...");
-	if (flash_sect_erase
-	    (SW_BYTE_SECTOR_ADDR,
-	     (SW_BYTE_SECTOR_ADDR + SW_BYTE_SECTOR_OFFSET))) {
-		return -1;
-	}
-
-	printf ("Writing to Flash... ");
-	write_result =
-		flash_write ((char *)sector_buffer, SW_BYTE_SECTOR_ADDR,
-			     SW_BYTE_SECTOR_SIZE);
-	if (write_result != 0) {
-		flash_perror (write_result);
-		return -1;
-	} else {
-		printf ("done\n");
-		printf ("Software configuration byte is now: 0x%02x\n",
-			*((unsigned char *) (SW_BYTE_SECTOR_ADDR +
-					     SW_BYTE_SECTOR_OFFSET)));
-	}
-
-	return 0;
-}
-
-#define ONE_SECOND 1000000
-
-int do_pause (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	int pause_time;
-	unsigned int delay_time;
-	int break_loop = 0;
-
-	/* display value if no argument */
-	if (argc < 2) {
-		pause_time = 1;
-	}
-
-	else if (argc > 2) {
-		printf ("Too many arguments\n");
-		return -1;
-	} else {
-		pause_time = simple_strtoul (argv[1], NULL, 0);
-	}
-
-	printf ("Pausing with a poll time of %d, press any key to reactivate\n", pause_time);
-	delay_time = pause_time * ONE_SECOND;
-	while (break_loop == 0) {
-		udelay (delay_time);
-		if (serial_tstc () != 0) {
-			break_loop = 1;
-			/* eat user key presses */
-			while (serial_tstc () != 0) {
-				serial_getc ();
-			}
-		}
-	}
-
-	return 0;
-}
-
-int do_swreconfig (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	printf ("Triggering software reconfigure (software config byte is 0x%02x)...\n",
-		*((unsigned char *) (SW_BYTE_SECTOR_ADDR + SW_BYTE_SECTOR_OFFSET)));
-	udelay (1000);
-	*((unsigned char *) AP1000_CPLD_BASE) = 1;
-
-	return 0;
-}
-
-#define GET_DECIMAL(low_byte) ((low_byte >> 5) * 125)
-#define TEMP_BUSY_BIT   0x80
-#define TEMP_LHIGH_BIT  0x40
-#define TEMP_LLOW_BIT   0x20
-#define TEMP_EHIGH_BIT  0x10
-#define TEMP_ELOW_BIT   0x08
-#define TEMP_OPEN_BIT   0x04
-#define TEMP_ETHERM_BIT 0x02
-#define TEMP_LTHERM_BIT 0x01
-
-int do_temp_sensor (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	char cmd;
-	int ret_val = 0;
-	unsigned char temp_byte;
-	int temp;
-	int temp_low;
-	int low;
-	int low_low;
-	int high;
-	int high_low;
-	int therm;
-	unsigned char user_data[4] = { 0 };
-	int user_data_count = 0;
-	int ii;
-
-	if (argc > 1) {
-		cmd = argv[1][0];
-	} else {
-		cmd = 's';	/* default to status */
-	}
-
-	user_data_count = argc - 2;
-	for (ii = 0; ii < user_data_count; ii++) {
-		user_data[ii] = simple_strtoul (argv[2 + ii], NULL, 0);
-	}
-	switch (cmd) {
-	case 's':
-		if (I2CAccess
-		    (0x2, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		printf ("Status    : 0x%02x  ", temp_byte);
-		if (temp_byte & TEMP_BUSY_BIT)
-			printf ("BUSY ");
-
-		if (temp_byte & TEMP_LHIGH_BIT)
-			printf ("LHIGH ");
-
-		if (temp_byte & TEMP_LLOW_BIT)
-			printf ("LLOW ");
-
-		if (temp_byte & TEMP_EHIGH_BIT)
-			printf ("EHIGH ");
-
-		if (temp_byte & TEMP_ELOW_BIT)
-			printf ("ELOW ");
-
-		if (temp_byte & TEMP_OPEN_BIT)
-			printf ("OPEN ");
-
-		if (temp_byte & TEMP_ETHERM_BIT)
-			printf ("ETHERM ");
-
-		if (temp_byte & TEMP_LTHERM_BIT)
-			printf ("LTHERM");
-
-		printf ("\n");
-
-		if (I2CAccess
-		    (0x3, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		printf ("Config    : 0x%02x  ", temp_byte);
-
-		if (I2CAccess
-		    (0x4, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			printf ("\n");
-			goto fail;
-		}
-		printf ("Conversion: 0x%02x\n", temp_byte);
-		if (I2CAccess
-		    (0x22, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		printf ("Cons Alert: 0x%02x  ", temp_byte);
-
-		if (I2CAccess
-		    (0x21, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			printf ("\n");
-			goto fail;
-		}
-		printf ("Therm Hyst: %d\n", temp_byte);
-
-		if (I2CAccess
-		    (0x0, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		temp = temp_byte;
-		if (I2CAccess
-		    (0x6, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		low = temp_byte;
-		if (I2CAccess
-		    (0x5, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		high = temp_byte;
-		if (I2CAccess
-		    (0x20, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		therm = temp_byte;
-		printf ("Local Temp: %2d     Low: %2d     High: %2d     THERM: %2d\n", temp, low, high, therm);
-
-		if (I2CAccess
-		    (0x1, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		temp = temp_byte;
-		if (I2CAccess
-		    (0x10, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		temp_low = temp_byte;
-		if (I2CAccess
-		    (0x8, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		low = temp_byte;
-		if (I2CAccess
-		    (0x14, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		low_low = temp_byte;
-		if (I2CAccess
-		    (0x7, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		high = temp_byte;
-		if (I2CAccess
-		    (0x13, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		high_low = temp_byte;
-		if (I2CAccess
-		    (0x19, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		therm = temp_byte;
-		if (I2CAccess
-		    (0x11, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &temp_byte, I2C_READ) != 0) {
-			goto fail;
-		}
-		printf ("Ext Temp  : %2d.%03d Low: %2d.%03d High: %2d.%03d THERM: %2d Offset: %2d\n", temp, GET_DECIMAL (temp_low), low, GET_DECIMAL (low_low), high, GET_DECIMAL (high_low), therm, temp_byte);
-		break;
-	case 'l':		/* alter local limits : low, high, therm */
-		if (argc < 3) {
-			goto usage;
-		}
-
-		/* low */
-		if (I2CAccess
-		    (0xC, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &user_data[0], I2C_WRITE) != 0) {
-			goto fail;
-		}
-
-		if (user_data_count > 1) {
-			/* high */
-			if (I2CAccess
-			    (0xB, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-			     &user_data[1], I2C_WRITE) != 0) {
-				goto fail;
-			}
-		}
-
-		if (user_data_count > 2) {
-			/* therm */
-			if (I2CAccess
-			    (0x20, I2C_SENSOR_DEV,
-			     I2C_SENSOR_CHIP_SEL, &user_data[2],
-			     I2C_WRITE) != 0) {
-				goto fail;
-			}
-		}
-		break;
-	case 'e':		/* alter external limits: low, high, therm, offset */
-		if (argc < 3) {
-			goto usage;
-		}
-
-		/* low */
-		if (I2CAccess
-		    (0xE, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &user_data[0], I2C_WRITE) != 0) {
-			goto fail;
-		}
-
-		if (user_data_count > 1) {
-			/* high */
-			if (I2CAccess
-			    (0xD, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-			     &user_data[1], I2C_WRITE) != 0) {
-				goto fail;
-			}
-		}
-
-		if (user_data_count > 2) {
-			/* therm */
-			if (I2CAccess
-			    (0x19, I2C_SENSOR_DEV,
-			     I2C_SENSOR_CHIP_SEL, &user_data[2],
-			     I2C_WRITE) != 0) {
-				goto fail;
-			}
-		}
-
-		if (user_data_count > 3) {
-			/* offset */
-			if (I2CAccess
-			    (0x11, I2C_SENSOR_DEV,
-			     I2C_SENSOR_CHIP_SEL, &user_data[3],
-			     I2C_WRITE) != 0) {
-				goto fail;
-			}
-		}
-		break;
-	case 'c':		/* alter config settings: config, conv, cons alert, therm hyst */
-		if (argc < 3) {
-			goto usage;
-		}
-
-		/* config */
-		if (I2CAccess
-		    (0x9, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-		     &user_data[0], I2C_WRITE) != 0) {
-			goto fail;
-		}
-
-		if (user_data_count > 1) {
-			/* conversion */
-			if (I2CAccess
-			    (0xA, I2C_SENSOR_DEV, I2C_SENSOR_CHIP_SEL,
-			     &user_data[1], I2C_WRITE) != 0) {
-				goto fail;
-			}
-		}
-
-		if (user_data_count > 2) {
-			/* cons alert */
-			if (I2CAccess
-			    (0x22, I2C_SENSOR_DEV,
-			     I2C_SENSOR_CHIP_SEL, &user_data[2],
-			     I2C_WRITE) != 0) {
-				goto fail;
-			}
-		}
-
-		if (user_data_count > 3) {
-			/* therm hyst */
-			if (I2CAccess
-			    (0x21, I2C_SENSOR_DEV,
-			     I2C_SENSOR_CHIP_SEL, &user_data[3],
-			     I2C_WRITE) != 0) {
-				goto fail;
-			}
-		}
-		break;
-	default:
-		goto usage;
-	}
-
-	goto done;
-fail:
-	printf ("Access to sensor failed\n");
-	ret_val = -1;
-	goto done;
-usage:
-	printf ("Usage:\n%s\n", cmdtp->help);
-
-done:
-	return ret_val;
-}
-
-U_BOOT_CMD (temp, 6, 0, do_temp_sensor,
-	    "interact with the temperature sensor",
-	    "temp [s]\n"
-	    "        - Show status.\n"
-	    "temp l LOW [HIGH] [THERM]\n"
-	    "        - Set local limits.\n"
-	    "temp e LOW [HIGH] [THERM] [OFFSET]\n"
-	    "        - Set external limits.\n"
-	    "temp c CONFIG [CONVERSION] [CONS. ALERT] [THERM HYST]\n"
-	    "        - Set config options.\n"
-	    "\n"
-	    "All values can be decimal or hex (hex preceded with 0x).\n"
-	    "Only whole numbers are supported for external limits.");
-
-#if 0
-U_BOOT_CMD (loadace, 2, 0, do_loadace,
-	    "load fpga configuration from System ACE compact flash",
-	    "N\n"
-	    "    - Load configuration N (0-7) from System ACE compact flash\n"
-	    "loadace\n" "    - loads default configuration");
-#endif
-
-U_BOOT_CMD (swconfig, 2, 0, do_swconfigbyte,
-	    "display or modify the software configuration byte",
-	    "N [ADDRESS]\n"
-	    "    - set software configuration byte to N, optionally use ADDRESS as\n"
-	    "      location of buffer for flash copy\n"
-	    "swconfig\n" "    - display software configuration byte");
-
-U_BOOT_CMD (pause, 2, 0, do_pause,
-	    "sleep processor until any key is pressed with poll time of N seconds",
-	    "N\n"
-	    "    - sleep processor until any key is pressed with poll time of N seconds\n"
-	    "pause\n"
-	    "    - sleep processor until any key is pressed with poll time of 1 second");
-
-U_BOOT_CMD (swrecon, 1, 0, do_swreconfig,
-	    "trigger a board reconfigure to the software selected configuration",
-	    "\n"
-	    "    - trigger a board reconfigure to the software selected configuration");
-
-int board_eth_init(bd_t *bis)
-{
-	return pci_eth_init(bis);
-}