ppc4xx: Remove superfluous dram_init() call or replace it by initdram()

Historically the 405 U-Boot port had a dram_init() call in early init
stage. This function was still called from start.S and most of the time
coded in assembler. This is not needed anymore (since a long time) and
boards should implement the common initdram() function in C instead.

This patch now removed the dram_init() call from start.S and removes the
empty implementations that are scattered through most of the 405 board
ports. Some older board ports really implement this dram_init() though.
These are:

csb272
csb472
ERIC
EXBITGEN
W7OLMC
W7OLMG

I changed those boards to call this assembler dram_init() function now
from their board specific initdram() instead. This *should* work, but please
test again on those platforms. And it is perhaps a good idea that those
boards use some common 405 SDRAM initialization code from cpu/ppc4xx at
some time. So further patches welcome here.

Signed-off-by: Stefan Roese <sr@denx.de>

5 files changed, 3 insertions, 101 deletions

diff --git a/board/amcc/acadia/memory.c b/board/amcc/acadia/memory.c
index 709d41e..3dec315 100644
--- a/board/amcc/acadia/memory.c
+++ b/board/amcc/acadia/memory.c
@@ -33,14 +33,6 @@
 
 extern void board_pll_init_f(void);
 
-/*
- * sdram_init - Dummy implementation for start.S, spd_sdram used on this board!
- */
-void sdram_init(void)
-{
-	return;
-}
-
 #if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
 static void cram_bcr_write(u32 wr_val)
 {
@@ -116,10 +108,3 @@ long int initdram(int board_type)
 
 	return (CFG_MBYTES_RAM << 20);
 }
-
-#ifndef CONFIG_NAND_SPL
-int testdram(void)
-{
-	return (0);
-}
-#endif
diff --git a/board/amcc/bubinga/bubinga.c b/board/amcc/bubinga/bubinga.c
index 66e7509..9d508b8 100644
--- a/board/amcc/bubinga/bubinga.c
+++ b/board/amcc/bubinga/bubinga.c
@@ -66,14 +66,6 @@ int checkboard(void)
 	return (0);
 }
 
-/*
- * sdram_init - Dummy implementation for start.S, spd_sdram used on this board!
- */
-void sdram_init(void)
-{
-	return;
-}
-
 /* -------------------------------------------------------------------------
   initdram(int board_type) reads EEPROM via I2c. EEPROM contains all of
   the necessary info for SDRAM controller configuration
@@ -85,11 +77,3 @@ long int initdram(int board_type)
 	ret = spd_sdram();
 	return ret;
 }
-
-int testdram(void)
-{
-	/* TODO: XXX XXX XXX */
-	printf("test: xxx MB - ok\n");
-
-	return (0);
-}
diff --git a/board/amcc/makalu/makalu.c b/board/amcc/makalu/makalu.c
index adf604f..9baec9a 100644
--- a/board/amcc/makalu/makalu.c
+++ b/board/amcc/makalu/makalu.c
@@ -351,8 +351,3 @@ void ft_board_setup(void *blob, bd_t *bd)
 		       fdt_strerror(rc));
 }
 #endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
-
-void sdram_init(void)
-{
-	return;
-}
diff --git a/board/amcc/walnut/walnut.c b/board/amcc/walnut/walnut.c
index 292e026..641987e 100644
--- a/board/amcc/walnut/walnut.c
+++ b/board/amcc/walnut/walnut.c
@@ -86,14 +86,6 @@ int checkboard(void)
 }
 
 /*
- * sdram_init - Dummy implementation for start.S, spd_sdram used on this board!
- */
-void sdram_init(void)
-{
-	return;
-}
-
-/*
  * initdram(int board_type) reads EEPROM via I2c. EEPROM contains all of
  * the necessary info for SDRAM controller configuration
  */
@@ -101,11 +93,3 @@ long int initdram(int board_type)
 {
 	return spd_sdram();
 }
-
-int testdram(void)
-{
-	/* TODO: XXX XXX XXX */
-	printf("test: xxx MB - ok\n");
-
-	return (0);
-}
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c
index 212fab8..8345537 100644
--- a/board/amcc/yosemite/yosemite.c
+++ b/board/amcc/yosemite/yosemite.c
@@ -200,7 +200,7 @@ int checkboard(void)
 }
 
 /*************************************************************************
- *  sdram_init -- doesn't use serial presence detect.
+ *  initdram -- doesn't use serial presence detect.
  *
  *  Assumes:    256 MB, ECC, non-registered
  *              PLB @ 133 MHz
@@ -281,7 +281,7 @@ void sdram_tr1_set(int ram_address, int* tr1_value)
 	*tr1_value = (first_good + last_bad) / 2;
 }
 
-void sdram_init(void)
+long int initdram(int board)
 {
 	register uint reg;
 	int tr1_bank1, tr1_bank2;
@@ -327,57 +327,11 @@ void sdram_init(void)
 
 	sdram_tr1_set(0x00000000, &tr1_bank1);
 	sdram_tr1_set(0x08000000, &tr1_bank2);
-	mtsdram(mem_tr1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800) );
-}
+	mtsdram(mem_tr1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800));
 
-/*************************************************************************
- *  long int initdram
- *
- ************************************************************************/
-long int initdram(int board)
-{
-	sdram_init();
 	return CFG_SDRAM_BANKS * (CFG_KBYTES_SDRAM * 1024);	/* return bytes */
 }
 
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
-{
-	unsigned long *mem = (unsigned long *)0;
-	const unsigned long kend = (1024 / sizeof(unsigned long));
-	unsigned long k, n;
-
-	mtmsr(0);
-
-	for (k = 0; k < CFG_KBYTES_SDRAM;
-	     ++k, mem += (1024 / sizeof(unsigned long))) {
-		if ((k & 1023) == 0) {
-			printf("%3d MB\r", k / 1024);
-		}
-
-		memset(mem, 0xaaaaaaaa, 1024);
-		for (n = 0; n < kend; ++n) {
-			if (mem[n] != 0xaaaaaaaa) {
-				printf("SDRAM test fails at: %08x\n",
-				       (uint) & mem[n]);
-				return 1;
-			}
-		}
-
-		memset(mem, 0x55555555, 1024);
-		for (n = 0; n < kend; ++n) {
-			if (mem[n] != 0x55555555) {
-				printf("SDRAM test fails at: %08x\n",
-				       (uint) & mem[n]);
-				return 1;
-			}
-		}
-	}
-	printf("SDRAM test passes\n");
-	return 0;
-}
-#endif
-
 /*************************************************************************
  *  pci_pre_init
  *