Merge with /home/wd/git/u-boot/master

1 files changed, 220 insertions, 8 deletions

diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index ce1312c..e9b34dd 100644
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -21,13 +21,21 @@
  * MA 02111-1307 USA
  *
  * Port to AMCC-440SPE Evaluation Board SOP - April 2005
+ *
+ * PCIe supporting routines derived from Linux 440SPe PCIe driver.
  */
 
 #include <common.h>
 #include <ppc4xx.h>
 #include <asm/processor.h>
 #include <i2c.h>
+#include <asm-ppc/io.h>
+
 #include "yucca.h"
+#include "../cpu/ppc4xx/440spe_pcie.h"
+
+#undef PCIE_ENDPOINT
+/* #define PCIE_ENDPOINT 1 */
 
 void fpga_init (void);
 
@@ -39,6 +47,9 @@ int get_console_port(void);
 unsigned long ppcMfcpr(unsigned long cpr_reg);
 unsigned long ppcMfsdr(unsigned long sdr_reg);
 
+int ppc440spe_init_pcie_rootport(int port);
+void ppc440spe_setup_pcie(struct pci_controller *hose, int port);
+
 #define DEBUG_ENV
 #ifdef DEBUG_ENV
 #define DEBUGF(fmt,args...) printf(fmt ,##args)
@@ -555,10 +566,11 @@ int checkboard (void)
 
 static long int yucca_probe_for_dimms(void)
 {
-	long int 	dimm_installed[MAXDIMMS];
-	long int	dimm_num, probe_result;
-	long int	dimms_found = 0;
-	uchar		dimm_addr = IIC0_DIMM0_ADDR;
+	int 	dimm_installed[MAXDIMMS];
+	int	dimm_num, result;
+	int	dimms_found = 0;
+	uchar	dimm_addr = IIC0_DIMM0_ADDR;
+	uchar   dimm_spd_data[MAX_SPD_BYTES];
 
 	for (dimm_num = 0; dimm_num < MAXDIMMS; dimm_num++) {
 		/* check if there is a chip at the dimm address	*/
@@ -570,12 +582,28 @@ static long int yucca_probe_for_dimms(void)
 				dimm_addr = IIC0_DIMM1_ADDR;
 				break;
 		}
-		probe_result = i2c_probe(dimm_addr);
 
-		if (probe_result == 0) {
+		result = i2c_probe(dimm_addr);
+
+		memset(dimm_spd_data, 0, MAX_SPD_BYTES * sizeof(char));
+		if (result == 0) {
+			/* read first byte of SPD data, if there is any data */
+			result = i2c_read(dimm_addr, 0, 1, dimm_spd_data, 1);
+
+			if (result == 0) {
+				result = dimm_spd_data[0];
+				result = result > MAX_SPD_BYTES ?
+						MAX_SPD_BYTES : result;
+				result = i2c_read(dimm_addr, 0, 1,
+							dimm_spd_data, result);
+			}
+		}
+
+		if ((result == 0) &&
+		    (dimm_spd_data[64] == MICRON_SPD_JEDEC_ID)) {
 			dimm_installed[dimm_num] = TRUE;
 			dimms_found++;
-			debug("DIMM slot %d: DDR2 SDRAM detected\n",dimm_num);
+			debug("DIMM slot %d: DDR2 SDRAM detected\n", dimm_num);
 		} else {
 			dimm_installed[dimm_num] = FALSE;
 			debug("DIMM slot %d: Not populated or cannot sucessfully probe the DIMM\n", dimm_num);
@@ -908,6 +936,7 @@ void pci_target_init(struct pci_controller * hose )
 }
 #endif	/* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
 
+#if defined(CONFIG_PCI)
 /*************************************************************************
  *  is_pci_host
  *
@@ -923,12 +952,195 @@ void pci_target_init(struct pci_controller * hose )
  *
  *
  ************************************************************************/
-#if defined(CONFIG_PCI)
 int is_pci_host(struct pci_controller *hose)
 {
 	/* The yucca board is always configured as host. */
 	return 1;
 }
+
+int yucca_pcie_card_present(int port)
+{
+	u16 reg;
+
+	reg = in_be16((u16 *)FPGA_REG1C);
+	switch(port) {
+	case 0:
+		return !(reg & FPGA_REG1C_PE0_PRSNT);
+	case 1:
+		return !(reg & FPGA_REG1C_PE1_PRSNT);
+	case 2:
+		return !(reg & FPGA_REG1C_PE2_PRSNT);
+	default:
+		return 0;
+	}
+}
+
+/*
+ * For the given slot, set rootpoint mode, send power to the slot,
+ * turn on the green LED and turn off the yellow LED, enable the clock
+ * and turn off reset.
+ */
+void yucca_setup_pcie_fpga_rootpoint(int port)
+{
+	u16 power, clock, green_led, yellow_led, reset_off, rootpoint, endpoint;
+
+	switch(port) {
+	case 0:
+		rootpoint   = FPGA_REG1C_PE0_ROOTPOINT;
+		endpoint    = 0;
+		power 	    = FPGA_REG1A_PE0_PWRON;
+		green_led   = FPGA_REG1A_PE0_GLED;
+		clock 	    = FPGA_REG1A_PE0_REFCLK_ENABLE;
+		yellow_led  = FPGA_REG1A_PE0_YLED;
+		reset_off   = FPGA_REG1C_PE0_PERST;
+		break;
+	case 1:
+		rootpoint   = 0;
+		endpoint    = FPGA_REG1C_PE1_ENDPOINT;
+		power 	    = FPGA_REG1A_PE1_PWRON;
+		green_led   = FPGA_REG1A_PE1_GLED;
+		clock 	    = FPGA_REG1A_PE1_REFCLK_ENABLE;
+		yellow_led  = FPGA_REG1A_PE1_YLED;
+		reset_off   = FPGA_REG1C_PE1_PERST;
+		break;
+	case 2:
+		rootpoint   = 0;
+		endpoint    = FPGA_REG1C_PE2_ENDPOINT;
+		power 	    = FPGA_REG1A_PE2_PWRON;
+		green_led   = FPGA_REG1A_PE2_GLED;
+		clock 	    = FPGA_REG1A_PE2_REFCLK_ENABLE;
+		yellow_led  = FPGA_REG1A_PE2_YLED;
+		reset_off   = FPGA_REG1C_PE2_PERST;
+		break;
+
+	default:
+		return;
+	}
+
+	out_be16((u16 *)FPGA_REG1A,
+		 ~(power | clock | green_led) &
+		 (yellow_led | in_be16((u16 *)FPGA_REG1A)));
+
+	out_be16((u16 *)FPGA_REG1C,
+		 ~(endpoint | reset_off) &
+		 (rootpoint | in_be16((u16 *)FPGA_REG1C)));
+	/*
+	 * Leave device in reset for a while after powering on the
+	 * slot to give it a chance to initialize.
+	 */
+	udelay(250 * 1000);
+
+	out_be16((u16 *)FPGA_REG1C, reset_off | in_be16((u16 *)FPGA_REG1C));
+}
+/*
+ * For the given slot, set endpoint mode, send power to the slot,
+ * turn on the green LED and turn off the yellow LED, enable the clock
+ * .In end point mode reset bit is  read only.
+ */
+void yucca_setup_pcie_fpga_endpoint(int port)
+{
+	u16 power, clock, green_led, yellow_led, reset_off, rootpoint, endpoint;
+
+	switch(port) {
+	case 0:
+		rootpoint   = FPGA_REG1C_PE0_ROOTPOINT;
+		endpoint    = 0;
+		power 	    = FPGA_REG1A_PE0_PWRON;
+		green_led   = FPGA_REG1A_PE0_GLED;
+		clock 	    = FPGA_REG1A_PE0_REFCLK_ENABLE;
+		yellow_led  = FPGA_REG1A_PE0_YLED;
+		reset_off   = FPGA_REG1C_PE0_PERST;
+		break;
+	case 1:
+		rootpoint   = 0;
+		endpoint    = FPGA_REG1C_PE1_ENDPOINT;
+		power 	    = FPGA_REG1A_PE1_PWRON;
+		green_led   = FPGA_REG1A_PE1_GLED;
+		clock 	    = FPGA_REG1A_PE1_REFCLK_ENABLE;
+		yellow_led  = FPGA_REG1A_PE1_YLED;
+		reset_off   = FPGA_REG1C_PE1_PERST;
+		break;
+	case 2:
+		rootpoint   = 0;
+		endpoint    = FPGA_REG1C_PE2_ENDPOINT;
+		power 	    = FPGA_REG1A_PE2_PWRON;
+		green_led   = FPGA_REG1A_PE2_GLED;
+		clock 	    = FPGA_REG1A_PE2_REFCLK_ENABLE;
+		yellow_led  = FPGA_REG1A_PE2_YLED;
+		reset_off   = FPGA_REG1C_PE2_PERST;
+		break;
+
+	default:
+		return;
+	}
+
+	out_be16((u16 *)FPGA_REG1A,
+		 ~(power | clock | green_led) &
+		 (yellow_led | in_be16((u16 *)FPGA_REG1A)));
+
+	out_be16((u16 *)FPGA_REG1C,
+		 ~(rootpoint | reset_off) &
+		 (endpoint | in_be16((u16 *)FPGA_REG1C)));
+}
+
+static struct pci_controller pcie_hose[3] = {{0},{0},{0}};
+
+void pcie_setup_hoses(void)
+{
+	struct pci_controller *hose;
+	int i, bus;
+
+	/*
+	 * assume we're called after the PCIX hose is initialized, which takes
+	 * bus ID 0 and therefore start numbering PCIe's from 1.
+	 */
+	bus = 1;
+	for (i = 0; i <= 2; i++) {
+		/* Check for yucca card presence */
+		if (!yucca_pcie_card_present(i))
+			continue;
+
+#ifdef PCIE_ENDPOINT
+ 		yucca_setup_pcie_fpga_endpoint(i);
+ 		if (ppc440spe_init_pcie_endport(i)) {
+#else
+		yucca_setup_pcie_fpga_rootpoint(i);
+		if (ppc440spe_init_pcie_rootport(i)) {
+#endif
+			printf("PCIE%d: initialization failed\n", i);
+			continue;
+		}
+
+		hose = &pcie_hose[i];
+		hose->first_busno = bus;
+		hose->last_busno  = bus;
+		bus++;
+
+		/* setup mem resource */
+		pci_set_region(hose->regions + 0,
+			CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+			CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
+			CFG_PCIE_MEMSIZE,
+			PCI_REGION_MEM
+			);
+		hose->region_count = 1;
+		pci_register_hose(hose);
+
+#ifdef PCIE_ENDPOINT
+		ppc440spe_setup_pcie_endpoint(hose, i);
+		/*
+		 * Reson for no scanning is endpoint can not generate
+		 * upstream configuration accesses.
+		 */
+#else
+		ppc440spe_setup_pcie_rootpoint(hose, i);
+		/*
+		 * Config access can only go down stream
+		 */
+		hose->last_busno = pci_hose_scan(hose);
+#endif
+	}
+}
 #endif	/* defined(CONFIG_PCI) */
 
 int misc_init_f (void)