Merge branch 'master' of git://git.denx.de/u-boot-arm

1 files changed, 0 insertions, 148 deletions

diff --git a/board/actux1/actux1.c b/board/actux1/actux1.c
deleted file mode 100644
index 03ccd93..0000000
--- a/board/actux1/actux1.c
+++ /dev/null
@@ -1,148 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#ifdef CONFIG_PCI
-#include <pci.h>
-#include <asm/arch/ixp425pci.h>
-#endif
-
-#include "actux1_hw.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/* CS5: Debug port */
-	writel(0x9d520003, IXP425_EXP_CS5);
-	/* CS6: HwRel */
-	writel(0x81860001, IXP425_EXP_CS6);
-	/* CS7: LEDs */
-	writel(0x80900003, IXP425_EXP_CS7);
-	return 0;
-}
-
-int board_init(void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x00000100;
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
-
-	/* Setup GPIOs for PCI INTA */
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI1_INTA);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI1_INTA);
-
-	/* Setup GPIOs for 33MHz clock output */
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
-	writel(0x011001FF, IXP425_GPIO_GPCLKR);
-
-	udelay(533);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
-
-	ACTUX1_LED1(2);
-	ACTUX1_LED2(2);
-	ACTUX1_LED3(0);
-	ACTUX1_LED4(0);
-	ACTUX1_LED5(0);
-	ACTUX1_LED6(0);
-	ACTUX1_LED7(0);
-
-	ACTUX1_HS(ACTUX1_HS_DCD);
-
-	return 0;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-
-	puts("Board: AcTux-1 rev.");
-	putc(ACTUX1_BOARDREL + 'A' - 1);
-
-	if (i > 0) {
-		puts(", serial# ");
-		puts(buf);
-	}
-	putc('\n');
-
-	return 0;
-}
-
-/*************************************************************************
- * get_board_rev() - setup to pass kernel board revision information
- * 0 = reserved
- * 1 = Rev. A
- * 2 = Rev. B
- *************************************************************************/
-u32 get_board_rev(void)
-{
-	return ACTUX1_BOARDREL;
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
-	return 0;
-}
-
-
-#ifdef CONFIG_PCI
-struct pci_controller hose;
-
-void pci_init_board(void)
-{
-	pci_ixp_init(&hose);
-}
-#endif
-
-void reset_phy(void)
-{
-	u16 id1, id2;
-
-	/* initialize the PHY */
-	miiphy_reset("NPE0", CONFIG_PHY_ADDR);
-
-	miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1);
-	miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2);
-
-	id2 &= 0xFFF0;		/* mask out revision bits */
-
-	if (id1 == 0x13 && id2 == 0x78e0) {
-		/*
-		 * LXT971/LXT972 PHY: set LED outputs:
-		 * LED1(green) = Link/ACT,
-		 * LED2 (unused) = LINK,
-		 * LED3(red) = Coll
-		 */
-		miiphy_write("NPE0", CONFIG_PHY_ADDR, 20, 0xD432);
-	} else if (id1 == 0x143 && id2 == 0xbc30) {
-		/* BCM5241: default values are OK */
-	} else
-		printf("unknown ethernet PHY ID: %x %x\n", id1, id2);
-}