Seagate FreeAgent DockStar support

start with sheevaplug configuration
add modifications by Alexander Holler <holler@ahsoftware.de>
    change RAM definitions to one bank (128 MB)
    change ident string and prompt
define MTD partitions and default environment variables
add support for LEDs

Signed-off-by: Eric Cooper <ecc@cmu.edu>

1 files changed, 181 insertions, 0 deletions

diff --git a/board/Seagate/dockstar/dockstar.c b/board/Seagate/dockstar/dockstar.c
new file mode 100644
index 0000000..cab3a83
--- /dev/null
+++ b/board/Seagate/dockstar/dockstar.c
@@ -0,0 +1,181 @@
+/*
+ * Copyright (C) 2010  Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.c originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "dockstar.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	/*
+	 * default gpio configuration
+	 * There are maximum 64 gpios controlled through 2 sets of registers
+	 * the  below configuration configures mainly initial LED status
+	 */
+	kw_config_gpio(DOCKSTAR_OE_VAL_LOW,
+			DOCKSTAR_OE_VAL_HIGH,
+			DOCKSTAR_OE_LOW, DOCKSTAR_OE_HIGH);
+
+	/* Multi-Purpose Pins Functionality configuration */
+	u32 kwmpp_config[] = {
+		MPP0_NF_IO2,
+		MPP1_NF_IO3,
+		MPP2_NF_IO4,
+		MPP3_NF_IO5,
+		MPP4_NF_IO6,
+		MPP5_NF_IO7,
+		MPP6_SYSRST_OUTn,
+		MPP7_GPO,
+		MPP8_UART0_RTS,
+		MPP9_UART0_CTS,
+		MPP10_UART0_TXD,
+		MPP11_UART0_RXD,
+		MPP12_SD_CLK,
+		MPP13_SD_CMD,
+		MPP14_SD_D0,
+		MPP15_SD_D1,
+		MPP16_SD_D2,
+		MPP17_SD_D3,
+		MPP18_NF_IO0,
+		MPP19_NF_IO1,
+		MPP20_GPIO,
+		MPP21_GPIO,
+		MPP22_GPIO,
+		MPP23_GPIO,
+		MPP24_GPIO,
+		MPP25_GPIO,
+		MPP26_GPIO,
+		MPP27_GPIO,
+		MPP28_GPIO,
+		MPP29_TSMP9,
+		MPP30_GPIO,
+		MPP31_GPIO,
+		MPP32_GPIO,
+		MPP33_GPIO,
+		MPP34_GPIO,
+		MPP35_GPIO,
+		MPP36_GPIO,
+		MPP37_GPIO,
+		MPP38_GPIO,
+		MPP39_GPIO,
+		MPP40_GPIO,
+		MPP41_GPIO,
+		MPP42_GPIO,
+		MPP43_GPIO,
+		MPP44_GPIO,
+		MPP45_GPIO,
+		MPP46_GPIO,
+		MPP47_GPIO,
+		MPP48_GPIO,
+		MPP49_GPIO,
+		0
+	};
+	kirkwood_mpp_conf(kwmpp_config);
+	return 0;
+}
+
+int board_init(void)
+{
+	/*
+	 * arch number of board
+	 */
+	gd->bd->bi_arch_number = MACH_TYPE_DOCKSTAR;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+	u16 reg;
+	u16 devadr;
+	char *name = "egiga0";
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/* command to read PHY dev address */
+	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+		printf("Err..%s could not read PHY dev address\n",
+			__FUNCTION__);
+		return;
+	}
+
+	/*
+	 * Enable RGMII delay on Tx and Rx for CPU port
+	 * Ref: sec 4.7.2 of chip datasheet
+	 */
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
+	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+	/* reset the phy */
+	miiphy_reset(name, devadr);
+
+	printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
+
+#define GREEN_LED	(1 << 14)
+#define ORANGE_LED	(1 << 15)
+#define BOTH_LEDS	(GREEN_LED | ORANGE_LED)
+#define NEITHER_LED	0
+
+static void set_leds(u32 leds, u32 blinking)
+{
+	struct kwgpio_registers *r = (struct kwgpio_registers *)KW_GPIO1_BASE;
+	u32 oe = readl(&r->oe) | BOTH_LEDS;
+	writel(oe & ~leds, &r->oe);	/* active low */
+	u32 bl = readl(&r->blink_en) & ~BOTH_LEDS;
+	writel(bl | blinking, &r->blink_en);
+}
+
+void show_boot_progress(int val)
+{
+	switch (val) {
+	case 15:		/* booting Linux */
+		set_leds(BOTH_LEDS, NEITHER_LED);
+		break;
+	case 64:		/* Ethernet initialization */
+		set_leds(GREEN_LED, GREEN_LED);
+		break;
+	default:
+		if (val < 0)	/* error */
+			set_leds(ORANGE_LED, ORANGE_LED);
+		break;
+	}
+}