arm: Remove openrd boards

These boards have not been converted to generic board by the deadline.
Remove them.

Signed-off-by: Simon Glass <sjg@chromium.org>

1 files changed, 0 insertions, 161 deletions

diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c
deleted file mode 100644
index 55cf525..0000000
--- a/board/Marvell/openrd/openrd.c
+++ /dev/null
@@ -1,161 +0,0 @@
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.c:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include "openrd.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/*
-	 * default gpio configuration
-	 * There are maximum 64 gpios controlled through 2 sets of registers
-	 * the  below configuration configures mainly initial LED status
-	 */
-	mvebu_config_gpio(OPENRD_OE_VAL_LOW,
-			  OPENRD_OE_VAL_HIGH,
-			  OPENRD_OE_LOW, OPENRD_OE_HIGH);
-
-	/* Multi-Purpose Pins Functionality configuration */
-	static const u32 kwmpp_config[] = {
-		MPP0_NF_IO2,
-		MPP1_NF_IO3,
-		MPP2_NF_IO4,
-		MPP3_NF_IO5,
-		MPP4_NF_IO6,
-		MPP5_NF_IO7,
-		MPP6_SYSRST_OUTn,
-		MPP7_GPO,
-		MPP8_TW_SDA,
-		MPP9_TW_SCK,
-		MPP10_UART0_TXD,
-		MPP11_UART0_RXD,
-		MPP12_SD_CLK,
-		MPP13_SD_CMD, /* Alt UART1_TXD */
-		MPP14_SD_D0,  /* Alt UART1_RXD */
-		MPP15_SD_D1,
-		MPP16_SD_D2,
-		MPP17_SD_D3,
-		MPP18_NF_IO0,
-		MPP19_NF_IO1,
-		MPP20_GE1_0,
-		MPP21_GE1_1,
-		MPP22_GE1_2,
-		MPP23_GE1_3,
-		MPP24_GE1_4,
-		MPP25_GE1_5,
-		MPP26_GE1_6,
-		MPP27_GE1_7,
-		MPP28_GPIO,
-		MPP29_TSMP9,
-		MPP30_GE1_10,
-		MPP31_GE1_11,
-		MPP32_GE1_12,
-		MPP33_GE1_13,
-		MPP34_GPIO,   /* UART1 / SD sel */
-		MPP35_TDM_CH0_TX_QL,
-		MPP36_TDM_SPI_CS1,
-		MPP37_TDM_CH2_TX_QL,
-		MPP38_TDM_CH2_RX_QL,
-		MPP39_AUDIO_I2SBCLK,
-		MPP40_AUDIO_I2SDO,
-		MPP41_AUDIO_I2SLRC,
-		MPP42_AUDIO_I2SMCLK,
-		MPP43_AUDIO_I2SDI,
-		MPP44_AUDIO_EXTCLK,
-		MPP45_TDM_PCLK,
-		MPP46_TDM_FS,
-		MPP47_TDM_DRX,
-		MPP48_TDM_DTX,
-		MPP49_TDM_CH0_RX_QL,
-		0
-	};
-
-	kirkwood_mpp_conf(kwmpp_config, NULL);
-	return 0;
-}
-
-int board_init(void)
-{
-	/*
-	 * arch number of board
-	 */
-#if defined(CONFIG_BOARD_IS_OPENRD_BASE)
-	gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
-#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT)
-	gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT;
-#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
-	gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE;
-#endif
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-	return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1116/88E1121 PHY */
-void mv_phy_init(char *name)
-{
-	u16 reg;
-	u16 devadr;
-
-	if (miiphy_set_current_dev(name))
-		return;
-
-	/* command to read PHY dev address */
-	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
-		printf("Err..%s could not read PHY dev address\n",
-			__FUNCTION__);
-		return;
-	}
-
-	/*
-	 * Enable RGMII delay on Tx and Rx for CPU port
-	 * Ref: sec 4.7.2 of chip datasheet
-	 */
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
-	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
-	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
-	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
-	/* reset the phy */
-	miiphy_reset(name, devadr);
-
-	printf(PHY_NO" Initialized on %s\n", name);
-}
-
-void reset_phy(void)
-{
-	mv_phy_init("egiga0");
-
-#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT
-	/* Kirkwood ethernet driver is written with the assumption that in case
-	 * of multiple PHYs, their addresses are consecutive. But unfortunately
-	 * in case of OpenRD-Client, PHY addresses are not consecutive.*/
-	miiphy_write("egiga1", 0xEE, 0xEE, 24);
-#endif
-
-#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \
-	defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
-	/* configure and initialize both PHY's */
-	mv_phy_init("egiga1");
-#endif
-}
-#endif /* CONFIG_RESET_PHY_R */