Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  arm, davinci: add DAVINCI_MMC_CLKID
  arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
  arm, davinci: da850/dm365 lowlevel cleanup
  omap5: Add omap5_evm board build support.
  omap4/5: Add support for booting with CH.
  omap5: emif: Add emif/ddr configurations required for omap5 evm
  omap5: clocks: Add clocks support for omap5 platform.
  omap5: Add minimal support for omap5430.
  omap: Checkpatch fixes
  omap4: make omap4 code common for future reuse
  GCC4.6: Squash warnings in onenand_base.c
  GCC4.6: Fix common/usb.c on xscale
  OneNAND: Add simple OneNAND SPL
  PXA: vpac270: Enable the new generic MMC driver
  PXA: Cleanup serial_pxa
  PXA: Drop csb226 and innokom boards (unmaintained)
  m28evk: Fix comment about the number of RAM banks
  mx31: Fix checkpatch warnings in generic.c
  mx31: Use proper IO accessor for GPR register
  mx31: Remove duplicate definition for GPR register
  qong: Use generic function for configuring GPR register
  M28EVK: Enable USB HOST support
  iMX28: Add USB HOST driver
  iMX28: Add USB and USB PHY register definitions
  M28: Add memory detection into SPL
  iMX28: Fix ARM vector handling
  M28: Add doc/README.m28 documentation
  M28: Add MMC SPL
  iMX28: Add support for DENX M28EVK board
  iMX28: Add u-boot.sb target to Makefile
  iMX28: Add image header generator tool
  iMX28: Add driver for internal RTC
  iMX28: Add GPMI NAND driver
  iMX28: Add APBH DMA driver
  iMX28: Add SPI driver
  iMX28: Add GPIO control
  iMX28: Add I2C bus driver
  iMX28: Add PINMUX control
  FEC: Add support for iMX28 quirks
  iMX28: Add SSP MMC driver
  iMX28: Initial support for iMX28 CPU
  MX25: zmx25: GCC4.6 fix build warnings
  da850: add new config file for AM18xx
  BeagleBoard: config: Switch to ttyO2
  OMAP3: Change omap3_evm maintainer
  devkit8000: Fix NAND SPL on boards with 256MB NAND
  integrator: enable Vpp and disable flash protection
  integrator: add system controller header
  integrator: make flash writeable on boot
  integrator: use io-accessors for board init
  integrator: move text offset to config
  integrator: pass configs for core modules
  ARM: remove superfluous setting of arch_number in board specific code.
  SPL: Allow ARM926EJS to avoid compiling in the CPU support code
  integrator: do not test first part of the memory
  arm: a320: fix broken timer
  ARM: define CONFIG_MACH_TYPE for all ronetix boards
  dm646x: pass board revision info to kernel
  dm646x: add new configuration for dm6467T
  arm, davinci: Fix setting of the SDRAM configuration register
  arm, davinci: Remove the duplication of LPSC functions
  arm, davinci: Rename AM1808 lowlevel functions to DA850
  da8xxevm: fix build error
  ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE

1 files changed, 25 insertions, 13 deletions

diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h
index 1aacbb1..4146e21 100644
--- a/arch/arm/include/asm/arch-omap4/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap4/sys_proto.h
@@ -21,7 +21,7 @@
 #ifndef _SYS_PROTO_H_
 #define _SYS_PROTO_H_
 
-#include <asm/arch/omap4.h>
+#include <asm/arch/omap.h>
 #include <asm/arch/clocks.h>
 #include <asm/io.h>
 #include <asm/omap_common.h>
@@ -32,17 +32,17 @@ struct omap_sysinfo {
 };
 extern const struct omap_sysinfo sysinfo;
 
-extern struct omap4_prcm_regs *const prcm;
-
 void gpmc_init(void);
 void watchdog_init(void);
 u32 get_device_type(void);
 void do_set_mux(u32 base, struct pad_conf_entry const *array, int size);
+void set_muxconf_regs_essential(void);
 void set_muxconf_regs_non_essential(void);
 void sr32(void *, u32, u32, u32);
 u32 wait_on_value(u32, u32, void *, u32);
 void sdelay(unsigned long);
 void set_pl310_ctrl_reg(u32 val);
+void omap_rev_string(char *omap_rev_string);
 void setup_clocks_for_console(void);
 void prcm_init(void);
 void bypass_dpll(u32 *const base);
@@ -51,7 +51,17 @@ u32 get_sys_clk_freq(void);
 u32 omap4_ddr_clk(void);
 void cancel_out(u32 *num, u32 *den, u32 den_limit);
 void sdram_init(void);
-u32 omap4_sdram_size(void);
+u32 omap_sdram_size(void);
+u32 cortex_rev(void);
+void init_omap_revision(void);
+void do_io_settings(void);
+/*
+ * This is used to verify if the configuration header
+ * was executed by Romcode prior to control of transfer
+ * to the bootloader. SPL is responsible for saving and
+ * passing this to the u-boot.
+ */
+extern struct omap_boot_parameters boot_params;
 
 static inline u32 running_from_sdram(void)
 {
@@ -64,15 +74,17 @@ static inline u32 running_from_sdram(void)
 static inline u8 uboot_loaded_by_spl(void)
 {
 	/*
-	 * Configuration Header is not supported yet, so u-boot init running
-	 * from SDRAM implies that it was loaded by SPL. When this situation
-	 * changes one of these approaches could be taken:
-	 * i.  Pass a magic from SPL to U-Boot and U-Boot save it at a known
-	 *     location.
-	 * ii. Check the OPP. CH can support only 50% OPP while SPL initializes
-	 *     the DPLLs at 100% OPP.
+	 * u-boot can be running from sdram either because of configuration
+	 * Header or by SPL. If because of CH, then the romcode sets the
+	 * CHSETTINGS executed bit to true in the boot parameter structure that
+	 * it passes to the bootloader.This parameter is stored in the ch_flags
+	 * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
+	 * mandatory section if CH is present.
 	 */
-	return running_from_sdram();
+	if ((boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
+		return 0;
+	else
+		return running_from_sdram();
 }
 /*
  * The basic hardware init of OMAP(s_init()) can happen in 4
@@ -86,7 +98,7 @@ static inline u8 uboot_loaded_by_spl(void)
  * This function finds this context.
  * Defining as inline may help in compiling out unused functions in SPL
  */
-static inline u32 omap4_hw_init_context(void)
+static inline u32 omap_hw_init_context(void)
 {
 #ifdef CONFIG_SPL_BUILD
 	return OMAP_INIT_CONTEXT_SPL;