Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm: (167 commits)
  OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
  ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
  ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
  arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
  OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
  omap4: do not enable auxiliary cores
  omap4: do not enable fs-usb module
  omap4: panda: disable uart2 pads during boot
  igep00x0: change mpurate from 500 to auto
  igep00x0: enable the use of a plain text file
  tegra2: trivially enable 13 mhz crystal frequency
  tegra: Enable keyboard for Seaboard
  tegra: Switch on console mux and use environment for console
  tegra: Add tegra keyboard driver
  tegra: fdt: Add keyboard definitions for Seaboard
  tegra: fdt: Add keyboard controller definition
  tegra: Add keyboard support to funcmux
  input: Add support for keyboard matrix decoding from an fdt
  input: Add generic keyboard input handler
  input: Add linux/input.h for key code support
  fdt: Add fdtdec functions to read byte array
  tegra: Enable LP0 on Seaboard
  tegra: fdt: Add EMC data for Tegra2 Seaboard
  tegra: i2c: Add function to find DVC bus
  fdt: tegra: Add EMC node to device tree
  tegra: Add EMC settings for Seaboard
  tegra: Turn off power detect in board init
  tegra: Set up warmboot code on Nvidia boards
  tegra: Setup PMC scratch info from ap20 setup
  tegra: Add warmboot implementation
  tegra: Set up PMU for Nvidia boards
  tegra: Add PMU to manage power supplies
  tegra: Add EMC support for optimal memory timings
  tegra: Add header file for APB_MISC register
  tegra: Add tegra_get_chip_type() to detect SKU
  tegra: Add flow, gp_padctl, fuse, sdram headers
  tegra: Add crypto library for warmboot code
  tegra: Add functions to access low-level Osc/PLL details
  tegra: Move ap20.h header into arch location
  Add AES crypto library
  i2c: Add TPS6586X driver
  Add abs() macro to return absolute value
  fdt: Add function to return next compatible subnode
  fdt: Add function to locate an array in the device tree
  i.MX28: Avoid redefining serial_put[cs]()
  i.MX28: Check if WP detection is implemented at all
  i.MX28: Add battery boot components to SPL
  i.MX28: Reorder battery status functions in SPL
  i.MX28: Add LRADC init to i.MX28 SPL
  i.MX28: Add LRADC register definitions
  i.MX28: Shut down the LCD controller before reset
  i.MX28: Add LCDIF register definitions
  i.MX28: Implement boot pads sampling and reporting
  i.MX28: Improve passing of data from SPL to U-Boot
  M28EVK: Add SD update command
  M28EVK: Implement support for new board V2.0
  FEC: Abstract out register setup
  MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
  i.MX28: Add delay after CPU bypass is cleared
  spi: mxs: Allow other chip selects to work
  spi: mxs: Introduce spi_cs_is_valid()
  mx53loco: Remove unneeded gpio_set_value()
  mx53loco: Add CONFIG_REVISION_TAG
  mx53loco: Turn on VUSB regulator
  mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
  pmic: dialog: Avoid name conflicts
  imx: Add u-boot.imx as target for ARM9 i.MX SOCs
  i.MX2: Include asm/types.h in arch-mx25/imx-regs.h
  imx: usb: There is no such register
  i.MX25: usb: Set PORTSCx register
  imx: nand: Support flash based BBT
  i.MX25: This architecture has a GPIO4 too
  i.MX25: esdhc: Add mxc_get_clock infrastructure
  i.MX6: mx6q_sabrelite: add SATA bindings
  i.MX6: add enable_sata_clock()
  i.MX6: Add ANATOP regulator init
  mx28evk: add NAND support
  USB: ehci-mx6: Fix broken IO access
  M28: Scan only first 512 MB of DRAM to avoid memory wraparound
  Revert "i.MX28: Enable additional DRAM address bits"
  M28: Enable FDT support
  mx53loco: Add support for 1GHz operation for DA9053-based boards
  mx53loco: Allow to print CPU information at a later stage
  mx5: Add clock config interface
  imx-common: Factor out get_ahb_clk()
  i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
  mx31pdk: Allow booting a zImage kernel
  mx6qarm2: Allow booting a zImage kernel
  mx6qsabrelite: Allow booting a zImage kernel
  mx28evk: Allow booting a zImage kernel
  m28evk: Allow to booting a dt kernel
  mx28evk: Allow to booting a dt kernel
  mx6qsabrelite: No need to set the direction for GPIO3_23 again
  pmic: Add support for the Dialog DA9053 PMIC
  MX53: mx53loco: Add SATA support
  MX53: Add support to ESG ima3 board
  SATA: add driver for MX5 / MX6 SOCs
  MX53: add function to set SATA clock to internal
  SATA: check for return value from sata functions
  MX5: Add definitions for SATA controller
  NET: fec_mxc.c: Add a way to disable auto negotiation
  Define UART4 and UART5 base addresses
  EXYNOS: Change bits per pixel value proper for u-boot.
  EXYNOS: support TRATS board display function
  LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
  EXYNOS: support EXYNOS MIPI DSI interface driver.
  EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
  LCD: add data structure for EXYNOS display driver
  EXYNOS: add LCD and MIPI DSI clock interface.
  EXYNOS: definitions of system resgister and power management registers.
  SMDK5250: fix compiler warning
  misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
  misc:pmic:max8997 MAX8997 support for PMIC driver
  TRATS: modify the trats's configuration
  ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
  EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
  arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  cm-t35: add I2C multi-bus support
  include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
  include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
  omap3: Introduce weak misc_init_r
  omap730p2: Remove empty misc_init_r
  omap5912osk: Remove empty misc_init_r
  omap4+: Remove CONFIG_ARCH_CPU_INIT
  omap4: Remove CONFIG_SYS_MMC_SET_DEV
  OMAP3: pandora: drop console kernel argument
  OMAP3: pandora: revise GPIO configuration
  ...

1 files changed, 155 insertions, 69 deletions

diff --git a/arch/arm/cpu/arm926ejs/mx28/spl_power_init.c b/arch/arm/cpu/arm926ejs/mx28/spl_power_init.c
index aa4117d..4b09b0c 100644
--- a/arch/arm/cpu/arm926ejs/mx28/spl_power_init.c
+++ b/arch/arm/cpu/arm926ejs/mx28/spl_power_init.c
@@ -45,11 +45,11 @@ void mx28_power_clock2pll(void)
 	struct mx28_clkctrl_regs *clkctrl_regs =
 		(struct mx28_clkctrl_regs *)MXS_CLKCTRL_BASE;
 
-	writel(CLKCTRL_PLL0CTRL0_POWER,
-		&clkctrl_regs->hw_clkctrl_pll0ctrl0_set);
+	setbits_le32(&clkctrl_regs->hw_clkctrl_pll0ctrl0,
+			CLKCTRL_PLL0CTRL0_POWER);
 	early_delay(100);
-	writel(CLKCTRL_CLKSEQ_BYPASS_CPU,
-		&clkctrl_regs->hw_clkctrl_clkseq_clr);
+	setbits_le32(&clkctrl_regs->hw_clkctrl_clkseq,
+			CLKCTRL_CLKSEQ_BYPASS_CPU);
 }
 
 void mx28_power_clear_auto_restart(void)
@@ -104,6 +104,62 @@ void mx28_power_set_linreg(void)
 			POWER_VDDIOCTRL_LINREG_OFFSET_1STEPS_BELOW);
 }
 
+int mx28_get_batt_volt(void)
+{
+	struct mx28_power_regs *power_regs =
+		(struct mx28_power_regs *)MXS_POWER_BASE;
+	uint32_t volt = readl(&power_regs->hw_power_battmonitor);
+	volt &= POWER_BATTMONITOR_BATT_VAL_MASK;
+	volt >>= POWER_BATTMONITOR_BATT_VAL_OFFSET;
+	volt *= 8;
+	return volt;
+}
+
+int mx28_is_batt_ready(void)
+{
+	return (mx28_get_batt_volt() >= 3600);
+}
+
+int mx28_is_batt_good(void)
+{
+	struct mx28_power_regs *power_regs =
+		(struct mx28_power_regs *)MXS_POWER_BASE;
+	uint32_t volt = mx28_get_batt_volt();
+
+	if ((volt >= 2400) && (volt <= 4300))
+		return 1;
+
+	clrsetbits_le32(&power_regs->hw_power_5vctrl,
+		POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK,
+		0x3 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET);
+	writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK,
+		&power_regs->hw_power_5vctrl_clr);
+
+	clrsetbits_le32(&power_regs->hw_power_charge,
+		POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK,
+		POWER_CHARGE_STOP_ILIMIT_10MA | 0x3);
+
+	writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_clr);
+	writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK,
+		&power_regs->hw_power_5vctrl_clr);
+
+	early_delay(500000);
+
+	volt = mx28_get_batt_volt();
+
+	if (volt >= 3500)
+		return 0;
+
+	if (volt >= 2400)
+		return 1;
+
+	writel(POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK,
+		&power_regs->hw_power_charge_clr);
+	writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_set);
+
+	return 0;
+}
+
 void mx28_power_setup_5v_detect(void)
 {
 	struct mx28_power_regs *power_regs =
@@ -399,9 +455,14 @@ void mx28_power_enable_4p2(void)
 	mx28_power_init_4p2_regulator();
 
 	/* Shutdown battery (none present) */
-	clrbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_BO_MASK);
-	writel(POWER_CTRL_DCDC4P2_BO_IRQ, &power_regs->hw_power_ctrl_clr);
-	writel(POWER_CTRL_ENIRQ_DCDC4P2_BO, &power_regs->hw_power_ctrl_clr);
+	if (!mx28_is_batt_ready()) {
+		clrbits_le32(&power_regs->hw_power_dcdc4p2,
+				POWER_DCDC4P2_BO_MASK);
+		writel(POWER_CTRL_DCDC4P2_BO_IRQ,
+				&power_regs->hw_power_ctrl_clr);
+		writel(POWER_CTRL_ENIRQ_DCDC4P2_BO,
+				&power_regs->hw_power_ctrl_clr);
+	}
 
 	mx28_power_init_dcdc_4p2_source();
 
@@ -459,6 +520,50 @@ void mx28_powerdown(void)
 		&power_regs->hw_power_reset);
 }
 
+void mx28_batt_boot(void)
+{
+	struct mx28_power_regs *power_regs =
+		(struct mx28_power_regs *)MXS_POWER_BASE;
+
+	clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_PWDN_5VBRNOUT);
+	clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_ENABLE_DCDC);
+
+	clrbits_le32(&power_regs->hw_power_dcdc4p2,
+			POWER_DCDC4P2_ENABLE_DCDC | POWER_DCDC4P2_ENABLE_4P2);
+	writel(POWER_CHARGE_ENABLE_LOAD, &power_regs->hw_power_charge_clr);
+
+	/* 5V to battery handoff. */
+	setbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER);
+	early_delay(30);
+	clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER);
+
+	writel(POWER_CTRL_ENIRQ_DCDC4P2_BO, &power_regs->hw_power_ctrl_clr);
+
+	clrsetbits_le32(&power_regs->hw_power_minpwr,
+			POWER_MINPWR_HALFFETS, POWER_MINPWR_DOUBLE_FETS);
+
+	mx28_power_set_linreg();
+
+	clrbits_le32(&power_regs->hw_power_vdddctrl,
+		POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG);
+
+	clrbits_le32(&power_regs->hw_power_vddactrl,
+		POWER_VDDACTRL_DISABLE_FET | POWER_VDDACTRL_ENABLE_LINREG);
+
+	clrbits_le32(&power_regs->hw_power_vddioctrl,
+		POWER_VDDIOCTRL_DISABLE_FET);
+
+	setbits_le32(&power_regs->hw_power_5vctrl,
+		POWER_5VCTRL_PWD_CHARGE_4P2_MASK);
+
+	setbits_le32(&power_regs->hw_power_5vctrl,
+		POWER_5VCTRL_ENABLE_DCDC);
+
+	clrsetbits_le32(&power_regs->hw_power_5vctrl,
+		POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK,
+		0x8 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET);
+}
+
 void mx28_handle_5v_conflict(void)
 {
 	struct mx28_power_regs *power_regs =
@@ -483,23 +588,12 @@ void mx28_handle_5v_conflict(void)
 			mx28_powerdown();
 			break;
 		}
-	}
-}
 
-int mx28_get_batt_volt(void)
-{
-	struct mx28_power_regs *power_regs =
-		(struct mx28_power_regs *)MXS_POWER_BASE;
-	uint32_t volt = readl(&power_regs->hw_power_battmonitor);
-	volt &= POWER_BATTMONITOR_BATT_VAL_MASK;
-	volt >>= POWER_BATTMONITOR_BATT_VAL_OFFSET;
-	volt *= 8;
-	return volt;
-}
-
-int mx28_is_batt_ready(void)
-{
-	return (mx28_get_batt_volt() >= 3600);
+		if (tmp & POWER_STS_PSWITCH_MASK) {
+			mx28_batt_boot();
+			break;
+		}
+	}
 }
 
 void mx28_5v_boot(void)
@@ -553,62 +647,44 @@ void mx28_switch_vddd_to_dcdc_source(void)
 		POWER_VDDDCTRL_DISABLE_STEPPING);
 }
 
-int mx28_is_batt_good(void)
+void mx28_power_configure_power_source(void)
 {
+	int batt_ready, batt_good;
 	struct mx28_power_regs *power_regs =
 		(struct mx28_power_regs *)MXS_POWER_BASE;
-	uint32_t volt;
-
-	volt = readl(&power_regs->hw_power_battmonitor);
-	volt &= POWER_BATTMONITOR_BATT_VAL_MASK;
-	volt >>= POWER_BATTMONITOR_BATT_VAL_OFFSET;
-	volt *= 8;
+	struct mx28_lradc_regs *lradc_regs =
+		(struct mx28_lradc_regs *)MXS_LRADC_BASE;
 
-	if ((volt >= 2400) && (volt <= 4300))
-		return 1;
-
-	clrsetbits_le32(&power_regs->hw_power_5vctrl,
-		POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK,
-		0x3 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET);
-	writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK,
-		&power_regs->hw_power_5vctrl_clr);
-
-	clrsetbits_le32(&power_regs->hw_power_charge,
-		POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK,
-		POWER_CHARGE_STOP_ILIMIT_10MA | 0x3);
-
-	writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_clr);
-	writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK,
-		&power_regs->hw_power_5vctrl_clr);
-
-	early_delay(500000);
-
-	volt = readl(&power_regs->hw_power_battmonitor);
-	volt &= POWER_BATTMONITOR_BATT_VAL_MASK;
-	volt >>= POWER_BATTMONITOR_BATT_VAL_OFFSET;
-	volt *= 8;
-
-	if (volt >= 3500)
-		return 0;
-
-	if (volt >= 2400)
-		return 1;
-
-	writel(POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK,
-		&power_regs->hw_power_charge_clr);
-	writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_set);
+	mx28_src_power_init();
 
-	return 0;
-}
+	batt_ready = mx28_is_batt_ready();
 
-void mx28_power_configure_power_source(void)
-{
-	mx28_src_power_init();
+	if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) {
+		batt_good = mx28_is_batt_good();
+		if (batt_ready) {
+			/* 5V source detected, good battery detected. */
+			mx28_batt_boot();
+		} else {
+			if (batt_good) {
+				/* 5V source detected, low battery detceted. */
+			} else {
+				/* 5V source detected, bad battery detected. */
+				writel(LRADC_CONVERSION_AUTOMATIC,
+					&lradc_regs->hw_lradc_conversion_clr);
+				clrbits_le32(&power_regs->hw_power_battmonitor,
+					POWER_BATTMONITOR_BATT_VAL_MASK);
+			}
+			mx28_5v_boot();
+		}
+	} else {
+		/* 5V not detected, booting from battery. */
+		mx28_batt_boot();
+	}
 
-	mx28_5v_boot();
 	mx28_power_clock2pll();
 
 	mx28_init_batt_bo();
+
 	mx28_switch_vddd_to_dcdc_source();
 }
 
@@ -883,6 +959,13 @@ void mx28_power_set_vddd(uint32_t new_target, uint32_t new_brownout)
 			new_brownout << POWER_VDDDCTRL_BO_OFFSET_OFFSET);
 }
 
+void mx28_setup_batt_detect(void)
+{
+	mx28_lradc_init();
+	mx28_lradc_enable_batt_measurement();
+	early_delay(10);
+}
+
 void mx28_power_init(void)
 {
 	struct mx28_power_regs *power_regs =
@@ -892,6 +975,9 @@ void mx28_power_init(void)
 	mx28_power_clear_auto_restart();
 	mx28_power_set_linreg();
 	mx28_power_setup_5v_detect();
+
+	mx28_setup_batt_detect();
+
 	mx28_power_configure_power_source();
 	mx28_enable_output_rail_protection();