Remove HMI10 board support

Recent changes caused that the HMI10 board now is included in the
boards built by MAKEALL, which revealed that compilation for this
board has been broken for a long time:

ps2ser.c: In function 'ps2ser_init':
ps2ser.c:155: error: 'UART_LCR' undeclared (first use in this function)
ps2ser.c:155: error: (Each undeclared identifier is reported only once
ps2ser.c:155: error: for each function it appears in.)
ps2ser.c:156: error: 'UART_DLL' undeclared (first use in this function)
ps2ser.c:157: error: 'UART_DLM' undeclared (first use in this function)
ps2ser.c:159: error: 'UART_IER' undeclared (first use in this function)
ps2ser.c:160: error: 'UART_MCR' undeclared (first use in this function)
ps2ser.c:161: error: 'UART_FCR' undeclared (first use in this function)
ps2ser.c:162: error: 'UART_FCR_ENABLE_FIFO' undeclared (first use in this function)
ps2ser.c:166: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_putc':
ps2ser.c:198: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c:200: error: 'UART_TX' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_getc_hw':
ps2ser.c:224: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c:225: error: 'UART_RX' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_interrupt':
ps2ser.c:293: error: 'UART_IIR' undeclared (first use in this function)

The board is orphaned, and AFAICT has reached EOL.
Drop support for it.

Signed-off-by: Wolfgang Denk <wd@denx.de>

9 files changed, 23 insertions, 717 deletions

diff --git a/board/mbx8xx/pcmcia.c b/board/mbx8xx/pcmcia.c
index 69368d8..e672d8c 100644
--- a/board/mbx8xx/pcmcia.c
+++ b/board/mbx8xx/pcmcia.c
@@ -117,11 +117,7 @@ int pcmcia_hardware_enable (int slot)
 	debug ("[%d] %s: PIPR(%p)=0x%x\n",
 	       __LINE__,__FUNCTION__,
 	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-#ifndef CONFIG_HMI10
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-#else
 	if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
-#endif	/* CONFIG_HMI10 */
 		printf ("   No Card found\n");
 		return (1);
 	}
diff --git a/board/tqc/tqm8xx/tqm8xx.c b/board/tqc/tqm8xx/tqm8xx.c
index cde780b..940cc8f 100644
--- a/board/tqc/tqm8xx/tqm8xx.c
+++ b/board/tqc/tqm8xx/tqm8xx.c
@@ -430,29 +430,6 @@ static long int dram_size (long int mamr_value, long int *base, long int maxsize
 
 /* ------------------------------------------------------------------------- */
 
-#ifdef CONFIG_PS2MULT
-
-#ifdef CONFIG_HMI10
-#define BASE_BAUD ( 1843200 / 16 )
-struct serial_state rs_table[] = {
-	{ BASE_BAUD, 4,  (void*)0xec140000 },
-	{ BASE_BAUD, 2,  (void*)0xec150000 },
-	{ BASE_BAUD, 6,  (void*)0xec160000 },
-	{ BASE_BAUD, 10, (void*)0xec170000 },
-};
-
-#ifdef CONFIG_BOARD_EARLY_INIT_R
-int board_early_init_r (void)
-{
-	ps2mult_early_init();
-	return (0);
-}
-#endif
-#endif /* CONFIG_HMI10 */
-
-#endif /* CONFIG_PS2MULT */
-
-
 #ifdef CONFIG_MISC_INIT_R
 extern void load_sernum_ethaddr(void);
 int misc_init_r (void)
diff --git a/boards.cfg b/boards.cfg
index 0bf9c93..25a58f4 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -170,7 +170,6 @@ QS823		powerpc	mpc8xx		qs850		snmc
 QS850		powerpc	mpc8xx		qs850		snmc
 QS860T		powerpc	mpc8xx		qs860t		snmc
 stxxtc		powerpc	mpc8xx		stxxtc		stx
-HMI10		powerpc	mpc8xx		tqm8xx		tqc
 SM850		powerpc	mpc8xx		tqm8xx		tqc
 AMX860		powerpc	mpc8xx		amx860		westel
 csb272		powerpc	ppc4xx
diff --git a/common/cmd_ide.c b/common/cmd_ide.c
index 6aeca76..ea0f4a7 100644
--- a/common/cmd_ide.c
+++ b/common/cmd_ide.c
@@ -818,7 +818,7 @@ set_pcmcia_timing (int pmode)
 static void
 input_swap_data(int dev, ulong *sect_buf, int words)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar i;
 	volatile uchar *pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
 	volatile uchar *pbuf_odd  = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
@@ -858,7 +858,7 @@ input_swap_data(int dev, ulong *sect_buf, int words)
 static void
 output_data(int dev, ulong *sect_buf, int words)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar	*dbuf;
 	volatile uchar	*pbuf_even;
 	volatile uchar	*pbuf_odd;
@@ -910,7 +910,7 @@ output_data(int dev, ulong *sect_buf, int words)
 static void
 input_data(int dev, ulong *sect_buf, int words)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar	*dbuf;
 	volatile uchar	*pbuf_even;
 	volatile uchar	*pbuf_odd;
@@ -1544,7 +1544,6 @@ static void ide_reset (void)
 
 #if defined(CONFIG_IDE_LED)	&& \
    !defined(CONFIG_CPC45)	&& \
-   !defined(CONFIG_HMI10)	&& \
    !defined(CONFIG_KUP4K)	&& \
    !defined(CONFIG_KUP4X)
 
@@ -1586,7 +1585,7 @@ int ide_device_present(int dev)
 static void
 output_data_shorts(int dev, ushort *sect_buf, int shorts)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar	*dbuf;
 	volatile uchar	*pbuf_even;
 	volatile uchar	*pbuf_odd;
@@ -1618,7 +1617,7 @@ output_data_shorts(int dev, ushort *sect_buf, int shorts)
 static void
 input_data_shorts(int dev, ushort *sect_buf, int shorts)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar	*dbuf;
 	volatile uchar	*pbuf_even;
 	volatile uchar	*pbuf_odd;
diff --git a/drivers/input/ps2ser.c b/drivers/input/ps2ser.c
index 8d0b6d6..a655a16 100644
--- a/drivers/input/ps2ser.c
+++ b/drivers/input/ps2ser.c
@@ -46,8 +46,7 @@ DECLARE_GLOBAL_DATA_PTR;
 #error CONFIG_PS2SERIAL must be in 1 ... 6
 #endif
 
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 
 #if CONFIG_PS2SERIAL == 1
 #define COM_BASE (CONFIG_SYS_CCSRBAR+0x4500)
@@ -57,17 +56,12 @@ DECLARE_GLOBAL_DATA_PTR;
 #error CONFIG_PS2SERIAL must be in 1 ... 2
 #endif
 
-#endif /* CONFIG_MPC5xxx / CONFIG_MPC8540 / other */
+#endif /* CONFIG_MPC5xxx / other */
 
 static int	ps2ser_getc_hw(void);
 static void	ps2ser_interrupt(void *dev_id);
 
 extern struct	serial_state rs_table[]; /* in serial.c */
-#if !defined(CONFIG_MPC5xxx) && !defined(CONFIG_MPC8540) && \
-    !defined(CONFIG_MPC8541) && !defined(CONFIG_MPC8548) && \
-    !defined(CONFIG_MPC8555)
-static struct	serial_state *state;
-#endif
 
 static u_char	ps2buf[PS2BUF_SIZE];
 static atomic_t	ps2buf_cnt;
@@ -111,8 +105,8 @@ int ps2ser_init(void)
 	return (0);
 }
 
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
+
 int ps2ser_init(void)
 {
 	NS16550_t com_port = (NS16550_t)COM_BASE;
@@ -128,76 +122,24 @@ int ps2ser_init(void)
 	return (0);
 }
 
-#else /* !CONFIG_MPC5xxx && !CONFIG_MPC8540 / other */
-
-static inline unsigned int ps2ser_in(int offset)
-{
-	return readb((unsigned long) state->iomem_base + offset);
-}
-
-static inline void ps2ser_out(int offset, int value)
-{
-	writeb(value, (unsigned long) state->iomem_base + offset);
-}
-
-int ps2ser_init(void)
-{
-	int quot;
-	unsigned cval;
-
-	state = rs_table + CONFIG_PS2SERIAL;
-
-	quot = state->baud_base / PS2SER_BAUD;
-	cval = 0x3; /* 8N1 - 8 data bits, no parity bits, 1 stop bit */
-
-	  /* Set speed, enable interrupts, enable FIFO
-	   */
-	ps2ser_out(UART_LCR, cval | UART_LCR_DLAB);
-	ps2ser_out(UART_DLL, quot & 0xff);
-	ps2ser_out(UART_DLM, quot >> 8);
-	ps2ser_out(UART_LCR, cval);
-	ps2ser_out(UART_IER, UART_IER_RDI);
-	ps2ser_out(UART_MCR, UART_MCR_OUT2 | UART_MCR_DTR | UART_MCR_RTS);
-	ps2ser_out(UART_FCR,
-	    UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
-
-	/* If we read 0xff from the LSR, there is no UART here
-	 */
-	if (ps2ser_in(UART_LSR) == 0xff) {
-		printf ("ps2ser.c: no UART found\n");
-		return -1;
-	}
-
-	irq_install_handler(state->irq, ps2ser_interrupt, NULL);
-
-	return 0;
-}
-#endif /* CONFIG_MPC5xxx / CONFIG_MPC8540 / other */
+#endif /* CONFIG_MPC5xxx / other */
 
 void ps2ser_putc(int chr)
 {
 #ifdef CONFIG_MPC5xxx
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	NS16550_t com_port = (NS16550_t)COM_BASE;
 #endif
-#ifdef DEBUG
-	printf(">>>> 0x%02x\n", chr);
-#endif
+	debug(">>>> 0x%02x\n", chr);
 
 #ifdef CONFIG_MPC5xxx
 	while (!(psc->psc_status & PSC_SR_TXRDY));
 
 	psc->psc_buffer_8 = chr;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	while ((com_port->lsr & UART_LSR_THRE) == 0);
 	com_port->thr = chr;
-#else
-	while (!(ps2ser_in(UART_LSR) & UART_LSR_THRE));
-
-	ps2ser_out(UART_TX, chr);
 #endif
 }
 
@@ -205,8 +147,7 @@ static int ps2ser_getc_hw(void)
 {
 #ifdef CONFIG_MPC5xxx
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	NS16550_t com_port = (NS16550_t)COM_BASE;
 #endif
 	int res = -1;
@@ -215,15 +156,10 @@ static int ps2ser_getc_hw(void)
 	if (psc->psc_status & PSC_SR_RXRDY) {
 		res = (psc->psc_buffer_8);
 	}
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	if (com_port->lsr & UART_LSR_DR) {
 		res = com_port->rbr;
 	}
-#else
-	if (ps2ser_in(UART_LSR) & UART_LSR_DR) {
-		res = (ps2ser_in(UART_RX));
-	}
 #endif
 
 	return res;
@@ -234,9 +170,7 @@ int ps2ser_getc(void)
 	volatile int chr;
 	int flags;
 
-#ifdef DEBUG
-	printf("<< ");
-#endif
+	debug("<< ");
 
 	flags = disable_interrupts();
 
@@ -251,11 +185,10 @@ int ps2ser_getc(void)
 	}
 	while (chr < 0);
 
-	if (flags) enable_interrupts();
+	if (flags)
+		enable_interrupts();
 
-#ifdef DEBUG
-	printf("0x%02x\n", chr);
-#endif
+	debug("0x%02x\n", chr);
 
 	return chr;
 }
@@ -275,8 +208,7 @@ static void ps2ser_interrupt(void *dev_id)
 {
 #ifdef CONFIG_MPC5xxx
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	NS16550_t com_port = (NS16550_t)COM_BASE;
 #endif
 	int chr;
@@ -286,11 +218,8 @@ static void ps2ser_interrupt(void *dev_id)
 		chr = ps2ser_getc_hw();
 #ifdef CONFIG_MPC5xxx
 		status = psc->psc_status;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
-		status = com_port->lsr;
 #else
-		status = ps2ser_in(UART_IIR);
+		status = com_port->lsr;
 #endif
 		if (chr < 0) continue;
 
@@ -303,13 +232,9 @@ static void ps2ser_interrupt(void *dev_id)
 		}
 #ifdef CONFIG_MPC5xxx
 	} while (status & PSC_SR_RXRDY);
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
-	} while (status & UART_LSR_DR);
 #else
-	} while (status & UART_IIR_RDI);
+	} while (status & UART_LSR_DR);
 #endif
-
 	if (atomic_read(&ps2buf_cnt)) {
 		ps2mult_callback(atomic_read(&ps2buf_cnt));
 	}
diff --git a/drivers/pcmcia/mpc8xx_pcmcia.c b/drivers/pcmcia/mpc8xx_pcmcia.c
index 7030574..74a50f1 100644
--- a/drivers/pcmcia/mpc8xx_pcmcia.c
+++ b/drivers/pcmcia/mpc8xx_pcmcia.c
@@ -57,12 +57,6 @@ static const u_int m8xx_size_to_gray[M8XX_SIZES_NO] =
 
 /* -------------------------------------------------------------------- */
 
-#ifdef	CONFIG_HMI10
-#define	HMI10_FRAM_TIMING	(	PCMCIA_SHT(2)	\
-				|	PCMCIA_SST(2)	\
-				|	PCMCIA_SL(4))
-#endif
-
 #if	defined(CONFIG_LWMON) || defined(CONFIG_NSCU)
 #define	CONFIG_SYS_PCMCIA_TIMING	(	PCMCIA_SHT(9)	\
 				|	PCMCIA_SST(3)	\
@@ -106,17 +100,6 @@ int pcmcia_on (void)
 		switch (i) {
 #ifdef	CONFIG_IDE_8xx_PCCARD
 		case 4:
-#ifdef	CONFIG_HMI10
-		{	/* map FRAM area */
-			win->or = (	PCMCIA_BSIZE_256K
-				|	PCMCIA_PPS_8
-				|	PCMCIA_PRS_ATTR
-				|	slotbit
-				|	PCMCIA_PV
-				|	HMI10_FRAM_TIMING );
-			break;
-		}
-#endif
 		case 0:	{	/* map attribute memory */
 			win->or = (	PCMCIA_BSIZE_64M
 				|	PCMCIA_PPS_8
@@ -147,18 +130,6 @@ int pcmcia_on (void)
 			break;
 		}
 #endif	/* CONFIG_IDE_8xx_PCCARD */
-#ifdef	CONFIG_HMI10
-		case 3: {	/* map I/O window for 4xUART data/ctrl */
-			win->br += 0x40000;
-			win->or = (	PCMCIA_BSIZE_256K
-				|	PCMCIA_PPS_8
-				|	PCMCIA_PRS_IO
-				|	slotbit
-				|	PCMCIA_PV
-				|	CONFIG_SYS_PCMCIA_TIMING );
-			break;
-		}
-#endif	/* CONFIG_HMI10 */
 		default:	/* set to not valid */
 			win->or = 0;
 			break;
diff --git a/drivers/pcmcia/tqm8xx_pcmcia.c b/drivers/pcmcia/tqm8xx_pcmcia.c
index 6ba8b5c..ca1a9fe 100644
--- a/drivers/pcmcia/tqm8xx_pcmcia.c
+++ b/drivers/pcmcia/tqm8xx_pcmcia.c
@@ -36,39 +36,6 @@
 #define	power_on_5_0(slot)	do {} while (0)
 #define	power_on_3_3(slot)	do {} while (0)
 
-#elif	defined(CONFIG_HMI10)
-
-static inline void power_config(int slot)
-{
-	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
-	/*
-	 * Configure Port B  pins for
-	 * 5 Volts Enable and 3 Volts enable
-	*/
-	immap->im_cpm.cp_pbpar &= ~(0x00000300);
-}
-
-static inline void power_off(int slot)
-{
-	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
-	/* remove all power */
-	immap->im_cpm.cp_pbdat |= 0x00000300;
-}
-
-static inline void power_on_5_0(int slot)
-{
-	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
-	immap->im_cpm.cp_pbdat &= ~(0x0000100);
-	immap->im_cpm.cp_pbdir |= 0x00000300;
-}
-
-static inline void power_on_3_3(int slot)
-{
-	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
-	immap->im_cpm.cp_pbdat &= ~(0x0000200);
-	immap->im_cpm.cp_pbdir |= 0x00000300;
-}
-
 #elif	defined(CONFIG_VIRTLAB2)
 
 #define	power_config(slot)	do {} while (0)
@@ -128,21 +95,12 @@ static inline void power_on_3_3(int slot)
 
 #endif
 
-#ifdef	CONFIG_HMI10
-static inline int check_card_is_absent(int slot)
-{
-	volatile pcmconf8xx_t *pcmp =
-		(pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-	return pcmp->pcmc_pipr & (0x10000000 >> (slot << 4));
-}
-#else
 static inline int check_card_is_absent(int slot)
 {
 	volatile pcmconf8xx_t *pcmp =
 		(pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
 	return pcmp->pcmc_pipr & (0x18000000 >> (slot << 4));
 }
-#endif
 
 #ifdef	NSCU_OE_INV
 #define	NSCU_GCRX_CXOE	0
diff --git a/include/configs/HMI10.h b/include/configs/HMI10.h
deleted file mode 100644
index 2747d8c..0000000
--- a/include/configs/HMI10.h
+++ /dev/null
@@ -1,504 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_HMI10
-#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
-#define CONFIG_TQM823L		1	/* ...on a TQM8xxL module	*/
-
-#define CONFIG_LCD
-#define CONFIG_NEC_NL6448BC33_54	/* NEC NL6448BC33_54 display	*/
-
-#ifdef	CONFIG_LCD			/* with LCD controller ?	*/
-#define CONFIG_SPLASH_SCREEN		/* ... with splashscreen support*/
-#endif
-
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define CONFIG_PS2KBD			/* AT-PS/2 Keyboard		*/
-#define CONFIG_PS2MULT			/* .. on PS/2 Multiplexer	*/
-#define CONFIG_PS2SERIAL	2	/* .. on COM3			*/
-#define CONFIG_PS2MULT_DELAY	(CONFIG_SYS_HZ/2)	/* Initial delay	*/
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/HMI10/uImage\0"				\
-	"kernel_addr=40040000\0"					\
-	"ramdisk_addr=40100000\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define	CONFIG_BOARD_EARLY_INIT_R 1
-#define CONFIG_MISC_INIT_R	  1
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-/* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		40000	/* 40 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
-/* Software (bit-bang) I2C driver configuration */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#define CONFIG_CAN_DRIVER	1	/* CAN Driver support enabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_RTC_DS1337		/* Use ds1337 rtc via i2c	*/
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68		/* at address 0x68		*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-#ifdef	CONFIG_SPLASH_SCREEN
-    #define CONFIG_CMD_BMP
-#endif
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt	*/
-
-#if 0
-#define CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-#endif
-#ifdef	CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-#define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
-#define CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size	  of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0100000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4100000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8100000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC100000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-#define PCMCIA_MEM_WIN_NO	5
-#define NSCU_OE_INV		1		/* PCMCIA_GCRX_CXOE is inverted */
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-#ifndef CONFIG_STATUS_LED		/* Status and IDE LED's are mutually exclusive */
-#define CONFIG_IDE_LED		1	/* LED   for ide supported	*/
-#endif
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096	 Rows from SDRAM example configuration
- * 1000	 factor s -> ms
- *   32	 PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4	 Number of refresh cycles per period
- *   64	 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/status_led.h b/include/status_led.h
index f213595..b39ca64 100644
--- a/include/status_led.h
+++ b/include/status_led.h
@@ -43,7 +43,7 @@ void status_led_tick (unsigned long timestamp);
 void status_led_set  (int led, int state);
 
 /*****  TQM8xxL  ********************************************************/
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_HMI10)
+#if defined(CONFIG_TQM8xxL)
 # define STATUS_LED_PAR		im_cpm.cp_pbpar
 # define STATUS_LED_DIR		im_cpm.cp_pbdir
 # define STATUS_LED_ODR		im_cpm.cp_pbodr
@@ -318,21 +318,6 @@ void status_led_set  (int led, int state);
 
 # define STATUS_LED_BOOT        0               /* LED 0 used for boot status */
 
-/*****  HMI10  **********************************************************/
-#elif defined(CONFIG_HMI10)
-# define STATUS_LED_PAR		im_ioport.iop_papar
-# define STATUS_LED_DIR		im_ioport.iop_padir
-# define STATUS_LED_ODR		im_ioport.iop_paodr
-# define STATUS_LED_DAT		im_ioport.iop_padat
-
-# define STATUS_LED_BIT		0x00000001	/* LED is on PA15 */
-# define STATUS_LED_PERIOD	(CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE	STATUS_LED_BLINKING
-
-# define STATUS_LED_ACTIVE	1		/* LED on for bit == 1	*/
-
-# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
-
 /*****  NetPhone   ********************************************************/
 #elif defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2)
 /* XXX empty just to avoid the error */