Merge branch 'master' of /home/wd/git/u-boot/custodians

35 files changed, 1944 insertions, 219 deletions

diff --git a/board/atmel/at91sam9261ek/at91sam9261ek.c b/board/atmel/at91sam9261ek/at91sam9261ek.c
index a89cb8b..0817e60 100644
--- a/board/atmel/at91sam9261ek/at91sam9261ek.c
+++ b/board/atmel/at91sam9261ek/at91sam9261ek.c
@@ -36,6 +36,7 @@
 #include <atmel_lcdc.h>
 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
 #include <net.h>
+#include <netdev.h>
 #endif
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -227,6 +228,12 @@ int board_init(void)
 	return 0;
 }
 
+#ifdef CONFIG_DRIVER_DM9000
+ int board_eth_init(bd_t *bis)
+ {
+	return dm9000_initialize(bis);
+ }
+ #endif
 int dram_init(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM;
diff --git a/board/davinci/common/misc.h b/board/davinci/common/misc.h
index 316159a..dc3cc41 100644
--- a/board/davinci/common/misc.h
+++ b/board/davinci/common/misc.h
@@ -22,7 +22,6 @@
 #ifndef __MISC_H
 #define __MISC_H
 
-extern int eth_hw_init(void);
 
 int dvevm_read_mac_address(uint8_t *buf);
 void dv_configure_mac_address(uint8_t *rom_enetaddr);
diff --git a/board/davinci/dvevm/dvevm.c b/board/davinci/dvevm/dvevm.c
index 8f38633..98937a9 100644
--- a/board/davinci/dvevm/dvevm.c
+++ b/board/davinci/dvevm/dvevm.c
@@ -73,9 +73,6 @@ int misc_init_r(void)
 	if (dvevm_read_mac_address(eeprom_enetaddr))
 		dv_configure_mac_address(eeprom_enetaddr);
 
-	if (!eth_hw_init())
-		printf("ethernet init failed!\n");
-
 	i2c_read(0x39, 0x00, 1, &video_mode, 1);
 
 	setenv("videostd", ((video_mode & 0x80) ? "pal" : "ntsc"));
diff --git a/board/davinci/schmoogie/schmoogie.c b/board/davinci/schmoogie/schmoogie.c
index 6e0f591..19c9580 100644
--- a/board/davinci/schmoogie/schmoogie.c
+++ b/board/davinci/schmoogie/schmoogie.c
@@ -130,8 +130,5 @@ int misc_init_r(void)
 		forceenv("serial#", (char *)&tmp[0]);
 	}
 
-	if (!eth_hw_init())
-		printf("ethernet init failed!\n");
-
 	return(0);
 }
diff --git a/board/davinci/sffsdr/sffsdr.c b/board/davinci/sffsdr/sffsdr.c
index 7f4ee36..c24b9e1 100644
--- a/board/davinci/sffsdr/sffsdr.c
+++ b/board/davinci/sffsdr/sffsdr.c
@@ -143,8 +143,5 @@ int misc_init_r(void)
 	if (sffsdr_read_mac_address(eeprom_enetaddr))
 		dv_configure_mac_address(eeprom_enetaddr);
 
-	if (!eth_hw_init())
-		printf("Ethernet init failed\n");
-
 	return(0);
 }
diff --git a/board/davinci/sonata/sonata.c b/board/davinci/sonata/sonata.c
index a0bea05..7f9d9bb 100644
--- a/board/davinci/sonata/sonata.c
+++ b/board/davinci/sonata/sonata.c
@@ -70,8 +70,5 @@ int misc_init_r(void)
 	if (dvevm_read_mac_address(eeprom_enetaddr))
 		dv_configure_mac_address(eeprom_enetaddr);
 
-	if (!eth_hw_init())
-		printf("ethernet init failed!\n");
-
 	return(0);
 }
diff --git a/board/freescale/m5253demo/m5253demo.c b/board/freescale/m5253demo/m5253demo.c
index b39cd4d..4772074 100644
--- a/board/freescale/m5253demo/m5253demo.c
+++ b/board/freescale/m5253demo/m5253demo.c
@@ -26,6 +26,7 @@
 
 #include <common.h>
 #include <asm/immap.h>
+#include <netdev.h>
 
 int checkboard(void)
 {
@@ -138,3 +139,11 @@ void ide_set_reset(int idereset)
 	}
 }
 #endif				/* CONFIG_CMD_IDE */
+
+
+#ifdef CONFIG_DRIVER_DM9000
+int board_eth_init(bd_t *bis)
+{
+	return dm9000_initialize(bis);
+}
+#endif
diff --git a/board/scb9328/scb9328.c b/board/scb9328/scb9328.c
index 3f6831b..428e8c9 100644
--- a/board/scb9328/scb9328.c
+++ b/board/scb9328/scb9328.c
@@ -19,6 +19,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -70,3 +71,10 @@ void show_boot_progress (int status)
 {
 	return;
 }
+
+#ifdef CONFIG_DRIVER_DM9000
+int board_eth_init(bd_t *bis)
+{
+	return dm9000_initialize(bis);
+}
+#endif
diff --git a/board/trizepsiv/conxs.c b/board/trizepsiv/conxs.c
index 7c6c855..5c0eb41 100644
--- a/board/trizepsiv/conxs.c
+++ b/board/trizepsiv/conxs.c
@@ -33,6 +33,7 @@
 
 #include <common.h>
 #include <asm/arch/pxa-regs.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -144,3 +145,10 @@ int dram_init (void)
 
 	return 0;
 }
+
+#ifdef CONFIG_DRIVER_DM9000
+int board_eth_init(bd_t *bis)
+{
+	return dm9000_initialize(bis);
+}
+#endif
diff --git a/cpu/arm926ejs/davinci/Makefile b/cpu/arm926ejs/davinci/Makefile
index 6eaa89c..e45ad25 100644
--- a/cpu/arm926ejs/davinci/Makefile
+++ b/cpu/arm926ejs/davinci/Makefile
@@ -30,7 +30,7 @@ LIB	= $(obj)lib$(SOC).a
 COBJS-y				+= cpu.o timer.o psc.o
 COBJS-$(CONFIG_SOC_DM355)	+= dm355.o
 COBJS-$(CONFIG_SOC_DM644X)	+= dm644x.o
-COBJS-$(CONFIG_DRIVER_TI_EMAC)	+= ether.o lxt972.o dp83848.o
+COBJS-$(CONFIG_DRIVER_TI_EMAC)	+= lxt972.o dp83848.o
 
 SOBJS	= reset.o
 
diff --git a/cpu/arm926ejs/davinci/cpu.c b/cpu/arm926ejs/davinci/cpu.c
index 29aead6..390cab8 100644
--- a/cpu/arm926ejs/davinci/cpu.c
+++ b/cpu/arm926ejs/davinci/cpu.c
@@ -21,6 +21,7 @@
  */
 
 #include <common.h>
+#include <netdev.h>
 #include <asm/arch/hardware.h>
 
 
@@ -129,3 +130,14 @@ int print_cpuinfo(void)
 
 #endif
 
+/*
+ * Initializes on-chip ethernet controllers.
+ * to override, implement board_eth_init()
+ */
+int cpu_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_DRIVER_TI_EMAC)
+	davinci_emac_initialize();
+#endif
+	return 0;
+}
diff --git a/drivers/net/4xx_enet.c b/drivers/net/4xx_enet.c
index 7bf3e0a..587605d 100644
--- a/drivers/net/4xx_enet.c
+++ b/drivers/net/4xx_enet.c
@@ -259,9 +259,6 @@ static const struct fixed_phy_port fixed_phy_port[] = {
 /*-----------------------------------------------------------------------------+
  * Global variables. TX and RX descriptors and buffers.
  *-----------------------------------------------------------------------------*/
-#if !defined(CONFIG_NET_MULTI)
-struct eth_device *emac0_dev = NULL;
-#endif
 
 /*
  * Get count of EMAC devices (doesn't have to be the max. possible number
@@ -1643,11 +1640,7 @@ int enetInt (struct eth_device *dev)
 	 * Because the mal is generic, we need to get the current
 	 * eth device
 	 */
-#if defined(CONFIG_NET_MULTI)
 	dev = eth_get_dev();
-#else
-	dev = emac0_dev;
-#endif
 
 	hw_p = dev->priv;
 
@@ -2066,60 +2059,13 @@ int ppc_4xx_eth_initialize (bd_t * bis)
 			virgin = 1;
 		}
 
-#if defined(CONFIG_NET_MULTI)
 		eth_register (dev);
-#else
-		emac0_dev = dev;
-#endif
 
-#if defined(CONFIG_NET_MULTI)
 #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
 		miiphy_register (dev->name,
 				 emac4xx_miiphy_read, emac4xx_miiphy_write);
 #endif
-#endif
 	}			/* end for each supported device */
 
 	return 0;
 }
-
-#if !defined(CONFIG_NET_MULTI)
-void eth_halt (void) {
-	if (emac0_dev) {
-		ppc_4xx_eth_halt(emac0_dev);
-		free(emac0_dev);
-		emac0_dev = NULL;
-	}
-}
-
-int eth_init (bd_t *bis)
-{
-	ppc_4xx_eth_initialize(bis);
-	if (emac0_dev) {
-		return ppc_4xx_eth_init(emac0_dev, bis);
-	} else {
-		printf("ERROR: ethaddr not set!\n");
-		return -1;
-	}
-}
-
-int eth_send(volatile void *packet, int length)
-{
-	return (ppc_4xx_eth_send(emac0_dev, packet, length));
-}
-
-int eth_rx(void)
-{
-	return (ppc_4xx_eth_rx(emac0_dev));
-}
-
-int emac4xx_miiphy_initialize (bd_t * bis)
-{
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
-	miiphy_register ("ppc_4xx_eth0",
-			 emac4xx_miiphy_read, emac4xx_miiphy_write);
-#endif
-
-	return 0;
-}
-#endif /* !defined(CONFIG_NET_MULTI) */
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index a360a50..c6097c3 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -40,6 +40,7 @@ COBJS-$(CONFIG_ENC28J60) += enc28j60.o
 COBJS-$(CONFIG_FSLDMAFEC) += fsl_mcdmafec.o mcfmii.o
 COBJS-$(CONFIG_GRETH) += greth.o
 COBJS-$(CONFIG_INCA_IP_SWITCH) += inca-ip_sw.o
+COBJS-$(CONFIG_KIRKWOOD_EGIGA) += kirkwood_egiga.o
 COBJS-$(CONFIG_DRIVER_KS8695ETH) += ks8695eth.o
 COBJS-$(CONFIG_DRIVER_LAN91C96) += lan91c96.o
 COBJS-$(CONFIG_MACB) += macb.o
@@ -64,6 +65,7 @@ COBJS-$(CONFIG_SH_ETHER) += sh_eth.o
 COBJS-$(CONFIG_DRIVER_SMC91111) += smc91111.o
 COBJS-$(CONFIG_DRIVER_SMC911X) += smc911x.o
 COBJS-$(CONFIG_TIGON3) += tigon3.o bcm570x_autoneg.o 5701rls.o
+COBJS-$(CONFIG_DRIVER_TI_EMAC) += davinci_emac.o
 COBJS-$(CONFIG_TSEC_ENET) += tsec.o
 COBJS-$(CONFIG_TSI108_ETH) += tsi108_eth.o
 COBJS-$(CONFIG_ULI526X) += uli526x.o
diff --git a/cpu/arm926ejs/davinci/ether.c b/drivers/net/davinci_emac.c
index f6f81df..fa8cee4 100644
--- a/cpu/arm926ejs/davinci/ether.c
+++ b/drivers/net/davinci_emac.c
@@ -40,21 +40,12 @@
 #include <command.h>
 #include <net.h>
 #include <miiphy.h>
+#include <malloc.h>
 #include <asm/arch/emac_defs.h>
 
-#ifdef CONFIG_DRIVER_TI_EMAC
-
-#ifdef CONFIG_CMD_NET
-
 unsigned int	emac_dbg = 0;
 #define debug_emac(fmt,args...)	if (emac_dbg) printf(fmt,##args)
 
-/* Internal static functions */
-static int davinci_eth_hw_init (void);
-static int davinci_eth_open (void);
-static int davinci_eth_close (void);
-static int davinci_eth_send_packet (volatile void *packet, int length);
-static int davinci_eth_rcv_packet (void);
 static void davinci_eth_mdio_enable(void);
 
 static int gen_init_phy(int phy_addr);
@@ -62,38 +53,10 @@ static int gen_is_phy_connected(int phy_addr);
 static int gen_get_link_speed(int phy_addr);
 static int gen_auto_negotiate(int phy_addr);
 
-/* Wrappers exported to the U-Boot proper */
-int eth_hw_init(void)
-{
-	return(davinci_eth_hw_init());
-}
-
-int eth_init(bd_t * bd)
-{
-	return(davinci_eth_open());
-}
-
-void eth_halt(void)
-{
-	davinci_eth_close();
-}
-
-int eth_send(volatile void *packet, int length)
-{
-	return(davinci_eth_send_packet(packet, length));
-}
-
-int eth_rx(void)
-{
-	return(davinci_eth_rcv_packet());
-}
-
 void eth_mdio_enable(void)
 {
 	davinci_eth_mdio_enable();
 }
-/* End of wrappers */
-
 
 static u_int8_t davinci_eth_mac_addr[] = { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff };
 
@@ -283,88 +246,11 @@ static int davinci_mii_phy_write(char *devname, unsigned char addr, unsigned cha
 	return(davinci_eth_phy_write(addr, reg, value) ? 0 : 1);
 }
 
-int davinci_eth_miiphy_initialize(bd_t *bis)
-{
-	miiphy_register(phy.name, davinci_mii_phy_read, davinci_mii_phy_write);
-
-	return(1);
-}
 #endif
 
-/*
- * This function initializes the emac hardware. It does NOT initialize
- * EMAC modules power or pin multiplexors, that is done by board_init()
- * much earlier in bootup process. Returns 1 on success, 0 otherwise.
- */
-static int davinci_eth_hw_init(void)
-{
-	u_int32_t	phy_id;
-	u_int16_t	tmp;
-	int		i;
-
-	davinci_eth_mdio_enable();
-
-	for (i = 0; i < 256; i++) {
-		if (adap_mdio->ALIVE)
-			break;
-		udelay(10);
-	}
-
-	if (i >= 256) {
-		printf("No ETH PHY detected!!!\n");
-		return(0);
-	}
-
-	/* Find if a PHY is connected and get it's address */
-	if (!davinci_eth_phy_detect())
-		return(0);
-
-	/* Get PHY ID and initialize phy_ops for a detected PHY */
-	if (!davinci_eth_phy_read(active_phy_addr, PHY_PHYIDR1, &tmp)) {
-		active_phy_addr = 0xff;
-		return(0);
-	}
-
-	phy_id = (tmp << 16) & 0xffff0000;
-
-	if (!davinci_eth_phy_read(active_phy_addr, PHY_PHYIDR2, &tmp)) {
-		active_phy_addr = 0xff;
-		return(0);
-	}
-
-	phy_id |= tmp & 0x0000ffff;
-
-	switch (phy_id) {
-		case PHY_LXT972:
-			sprintf(phy.name, "LXT972 @ 0x%02x", active_phy_addr);
-			phy.init = lxt972_init_phy;
-			phy.is_phy_connected = lxt972_is_phy_connected;
-			phy.get_link_speed = lxt972_get_link_speed;
-			phy.auto_negotiate = lxt972_auto_negotiate;
-			break;
-		case PHY_DP83848:
-			sprintf(phy.name, "DP83848 @ 0x%02x", active_phy_addr);
-			phy.init = dp83848_init_phy;
-			phy.is_phy_connected = dp83848_is_phy_connected;
-			phy.get_link_speed = dp83848_get_link_speed;
-			phy.auto_negotiate = dp83848_auto_negotiate;
-			break;
-		default:
-			sprintf(phy.name, "GENERIC @ 0x%02x", active_phy_addr);
-			phy.init = gen_init_phy;
-			phy.is_phy_connected = gen_is_phy_connected;
-			phy.get_link_speed = gen_get_link_speed;
-			phy.auto_negotiate = gen_auto_negotiate;
-	}
-
-	printf("Ethernet PHY: %s\n", phy.name);
-
-	return(1);
-}
-
 
 /* Eth device open */
-static int davinci_eth_open(void)
+static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 {
 	dv_reg_p		addr;
 	u_int32_t		clkdiv, cnt;
@@ -516,7 +402,7 @@ static void davinci_eth_ch_teardown(int ch)
 }
 
 /* Eth device close */
-static int davinci_eth_close(void)
+static void davinci_eth_close(struct eth_device *dev)
 {
 	debug_emac("+ emac_close\n");
 
@@ -528,7 +414,6 @@ static int davinci_eth_close(void)
 	adap_ewrap->EWCTL = 0;
 
 	debug_emac("- emac_close\n");
-	return(1);
 }
 
 static int tx_send_loop = 0;
@@ -537,7 +422,8 @@ static int tx_send_loop = 0;
  * This function sends a single packet on the network and returns
  * positive number (number of bytes transmitted) or negative for error
  */
-static int davinci_eth_send_packet (volatile void *packet, int length)
+static int davinci_eth_send_packet (struct eth_device *dev,
+					volatile void *packet, int length)
 {
 	int ret_status = -1;
 
@@ -584,7 +470,7 @@ static int davinci_eth_send_packet (volatile void *packet, int length)
 /*
  * This function handles receipt of a packet from the network
  */
-static int davinci_eth_rcv_packet (void)
+static int davinci_eth_rcv_packet (struct eth_device *dev)
 {
 	volatile emac_desc *rx_curr_desc;
 	volatile emac_desc *curr_desc;
@@ -650,6 +536,90 @@ static int davinci_eth_rcv_packet (void)
 	return (0);
 }
 
-#endif /* CONFIG_CMD_NET */
+/*
+ * This function initializes the emac hardware. It does NOT initialize
+ * EMAC modules power or pin multiplexors, that is done by board_init()
+ * much earlier in bootup process. Returns 1 on success, 0 otherwise.
+ */
+int davinci_emac_initialize(void)
+{
+	u_int32_t	phy_id;
+	u_int16_t	tmp;
+	int		i;
+	struct eth_device *dev;
+
+	dev = malloc(sizeof *dev);
+
+	if (dev == NULL)
+		return -1;
+
+	memset(dev, 0, sizeof *dev);
+
+	dev->iobase = 0;
+	dev->init = davinci_eth_open;
+	dev->halt = davinci_eth_close;
+	dev->send = davinci_eth_send_packet;
+	dev->recv = davinci_eth_rcv_packet;
+
+	eth_register(dev);
+
+	davinci_eth_mdio_enable();
+
+	for (i = 0; i < 256; i++) {
+		if (adap_mdio->ALIVE)
+			break;
+		udelay(10);
+	}
+
+	if (i >= 256) {
+		printf("No ETH PHY detected!!!\n");
+		return(0);
+	}
+
+	/* Find if a PHY is connected and get it's address */
+	if (!davinci_eth_phy_detect())
+		return(0);
+
+	/* Get PHY ID and initialize phy_ops for a detected PHY */
+	if (!davinci_eth_phy_read(active_phy_addr, PHY_PHYIDR1, &tmp)) {
+		active_phy_addr = 0xff;
+		return(0);
+	}
+
+	phy_id = (tmp << 16) & 0xffff0000;
+
+	if (!davinci_eth_phy_read(active_phy_addr, PHY_PHYIDR2, &tmp)) {
+		active_phy_addr = 0xff;
+		return(0);
+	}
+
+	phy_id |= tmp & 0x0000ffff;
+
+	switch (phy_id) {
+		case PHY_LXT972:
+			sprintf(phy.name, "LXT972 @ 0x%02x", active_phy_addr);
+			phy.init = lxt972_init_phy;
+			phy.is_phy_connected = lxt972_is_phy_connected;
+			phy.get_link_speed = lxt972_get_link_speed;
+			phy.auto_negotiate = lxt972_auto_negotiate;
+			break;
+		case PHY_DP83848:
+			sprintf(phy.name, "DP83848 @ 0x%02x", active_phy_addr);
+			phy.init = dp83848_init_phy;
+			phy.is_phy_connected = dp83848_is_phy_connected;
+			phy.get_link_speed = dp83848_get_link_speed;
+			phy.auto_negotiate = dp83848_auto_negotiate;
+			break;
+		default:
+			sprintf(phy.name, "GENERIC @ 0x%02x", active_phy_addr);
+			phy.init = gen_init_phy;
+			phy.is_phy_connected = gen_is_phy_connected;
+			phy.get_link_speed = gen_get_link_speed;
+			phy.auto_negotiate = gen_auto_negotiate;
+	}
 
-#endif /* CONFIG_DRIVER_TI_EMAC */
+	printf("Ethernet PHY: %s\n", phy.name);
+
+	miiphy_register(phy.name, davinci_mii_phy_read, davinci_mii_phy_write);
+	return(1);
+}
diff --git a/drivers/net/dm9000x.c b/drivers/net/dm9000x.c
index f139435..efe9135 100644
--- a/drivers/net/dm9000x.c
+++ b/drivers/net/dm9000x.c
@@ -103,14 +103,12 @@ typedef struct board_info {
 	void (*outblk)(volatile void *data_ptr, int count);
 	void (*inblk)(void *data_ptr, int count);
 	void (*rx_status)(u16 *RxStatus, u16 *RxLen);
+	struct eth_device netdev;
 } board_info_t;
 static board_info_t dm9000_info;
 
+
 /* function declaration ------------------------------------- */
-int eth_init(bd_t * bd);
-int eth_send(volatile void *, int);
-int eth_rx(void);
-void eth_halt(void);
 static int dm9000_probe(void);
 static u16 phy_read(int);
 static void phy_write(int, u16);
@@ -279,17 +277,16 @@ dm9000_reset(void)
 		printf("ERROR: resetting DM9000 -> not responding\n");
 }
 
-/* Initilize dm9000 board
+/* Initialize dm9000 board
 */
-int
-eth_init(bd_t * bd)
+static int dm9000_init(struct eth_device *dev, bd_t *bd)
 {
 	int i, oft, lnk;
 	u8 io_mode;
 	struct board_info *db = &dm9000_info;
 	uchar enetaddr[6];
 
-	DM9000_DBG("eth_init()\n");
+	DM9000_DBG("%s\n", __func__);
 
 	/* RESET device */
 	dm9000_reset();
@@ -411,13 +408,13 @@ eth_init(bd_t * bd)
   Hardware start transmission.
   Send a packet to media from the upper layer.
 */
-int
-eth_send(volatile void *packet, int length)
+static int dm9000_send(struct eth_device *netdev, volatile void *packet,
+		     int length)
 {
 	int tmo;
 	struct board_info *db = &dm9000_info;
 
-	DM9000_DMP_PACKET("eth_send", packet, length);
+	DM9000_DMP_PACKET(__func__ , packet, length);
 
 	DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */
 
@@ -453,10 +450,9 @@ eth_send(volatile void *packet, int length)
   Stop the interface.
   The interface is stopped when it is brought.
 */
-void
-eth_halt(void)
+static void dm9000_halt(struct eth_device *netdev)
 {
-	DM9000_DBG("eth_halt\n");
+	DM9000_DBG("%s\n", __func__);
 
 	/* RESET devie */
 	phy_write(0, 0x8000);	/* PHY RESET */
@@ -468,8 +464,7 @@ eth_halt(void)
 /*
   Received a packet and pass to upper layer
 */
-int
-eth_rx(void)
+static int dm9000_rx(struct eth_device *netdev)
 {
 	u8 rxbyte, *rdptr = (u8 *) NetRxPackets[0];
 	u16 RxStatus, RxLen = 0;
@@ -529,7 +524,7 @@ eth_rx(void)
 				dm9000_reset();
 			}
 		} else {
-			DM9000_DMP_PACKET("eth_rx", rdptr, RxLen);
+			DM9000_DMP_PACKET(__func__ , rdptr, RxLen);
 
 			DM9000_DBG("passing packet to upper layer\n");
 			NetReceive(NetRxPackets[0], RxLen);
@@ -621,3 +616,18 @@ phy_write(int reg, u16 value)
 	DM9000_iow(DM9000_EPCR, 0x0);	/* Clear phyxcer write command */
 	DM9000_DBG("phy_write(reg:0x%x, value:0x%x)\n", reg, value);
 }
+
+int dm9000_initialize(bd_t *bis)
+{
+	struct eth_device *dev = &(dm9000_info.netdev);
+
+	dev->init = dm9000_init;
+	dev->halt = dm9000_halt;
+	dev->send = dm9000_send;
+	dev->recv = dm9000_rx;
+	sprintf(dev->name, "dm9000");
+
+	eth_register(dev);
+
+	return 0;
+}
diff --git a/drivers/net/kirkwood_egiga.c b/drivers/net/kirkwood_egiga.c
new file mode 100644
index 0000000..b43bbf2
--- /dev/null
+++ b/drivers/net/kirkwood_egiga.c
@@ -0,0 +1,664 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * (C) Copyright 2003
+ * Ingo Assmus <ingo.assmus@keymile.com>
+ *
+ * based on - Driver for MV64360X ethernet ports
+ * Copyright (C) 2002 rabeeh@galileo.co.il
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <net.h>
+#include <malloc.h>
+#include <miiphy.h>
+#include <asm/errno.h>
+#include <asm/types.h>
+#include <asm/byteorder.h>
+#include <asm/arch/kirkwood.h>
+#include "kirkwood_egiga.h"
+
+/*
+ * smi_reg_read - miiphy_read callback function.
+ *
+ * Returns 16bit phy register value, or 0xffff on error
+ */
+static int smi_reg_read(char *devname, u8 phy_adr, u8 reg_ofs, u16 * data)
+{
+	struct eth_device *dev = eth_get_dev_by_name(devname);
+	struct kwgbe_device *dkwgbe = to_dkwgbe(dev);
+	struct kwgbe_registers *regs = dkwgbe->regs;
+	u32 smi_reg;
+	volatile u32 timeout;
+
+	/* Phyadr read request */
+	if (phy_adr == 0xEE && reg_ofs == 0xEE) {
+		/* */
+		*data = (u16) (KWGBEREG_RD(regs->phyadr) & PHYADR_MASK);
+		return 0;
+	}
+	/* check parameters */
+	if (phy_adr > PHYADR_MASK) {
+		printf("Err..(%s) Invalid PHY address %d\n",
+			__FUNCTION__, phy_adr);
+		return -EFAULT;
+	}
+	if (reg_ofs > PHYREG_MASK) {
+		printf("Err..(%s) Invalid register offset %d\n",
+			__FUNCTION__, reg_ofs);
+		return -EFAULT;
+	}
+
+	timeout = KWGBE_PHY_SMI_TIMEOUT;
+	/* wait till the SMI is not busy */
+	do {
+		/* read smi register */
+		smi_reg = KWGBEREG_RD(regs->smi);
+		if (timeout-- == 0) {
+			printf("Err..(%s) SMI busy timeout\n", __FUNCTION__);
+			return -EFAULT;
+		}
+	} while (smi_reg & KWGBE_PHY_SMI_BUSY_MASK);
+
+	/* fill the phy address and regiser offset and read opcode */
+	smi_reg = (phy_adr << KWGBE_PHY_SMI_DEV_ADDR_OFFS)
+		| (reg_ofs << KWGBE_SMI_REG_ADDR_OFFS)
+		| KWGBE_PHY_SMI_OPCODE_READ;
+
+	/* write the smi register */
+	KWGBEREG_WR(regs->smi, smi_reg);
+
+	/*wait till read value is ready */
+	timeout = KWGBE_PHY_SMI_TIMEOUT;
+
+	do {
+		/* read smi register */
+		smi_reg = KWGBEREG_RD(regs->smi);
+		if (timeout-- == 0) {
+			printf("Err..(%s) SMI read ready timeout\n",
+				__FUNCTION__);
+			return -EFAULT;
+		}
+	} while (!(smi_reg & KWGBE_PHY_SMI_READ_VALID_MASK));
+
+	/* Wait for the data to update in the SMI register */
+	for (timeout = 0; timeout < KWGBE_PHY_SMI_TIMEOUT; timeout++) ;
+
+	*data = (u16) (KWGBEREG_RD(regs->smi) & KWGBE_PHY_SMI_DATA_MASK);
+
+	debug("%s:(adr %d, off %d) value= %04x\n", __FUNCTION__, phy_adr,
+		reg_ofs, *data);
+
+	return 0;
+}
+
+/*
+ * smi_reg_write - imiiphy_write callback function.
+ *
+ * Returns 0 if write succeed, -EINVAL on bad parameters
+ * -ETIME on timeout
+ */
+static int smi_reg_write(char *devname, u8 phy_adr, u8 reg_ofs, u16 data)
+{
+	struct eth_device *dev = eth_get_dev_by_name(devname);
+	struct kwgbe_device *dkwgbe = to_dkwgbe(dev);
+	struct kwgbe_registers *regs = dkwgbe->regs;
+	u32 smi_reg;
+	volatile u32 timeout;
+
+	/* Phyadr write request*/
+	if (phy_adr == 0xEE && reg_ofs == 0xEE) {
+		KWGBEREG_WR(regs->phyadr, data);
+		return 0;
+	}
+
+	/* check parameters */
+	if (phy_adr > PHYADR_MASK) {
+		printf("Err..(%s) Invalid phy address\n", __FUNCTION__);
+		return -EINVAL;
+	}
+	if (reg_ofs > PHYREG_MASK) {
+		printf("Err..(%s) Invalid register offset\n", __FUNCTION__);
+		return -EINVAL;
+	}
+
+	/* wait till the SMI is not busy */
+	timeout = KWGBE_PHY_SMI_TIMEOUT;
+	do {
+		/* read smi register */
+		smi_reg = KWGBEREG_RD(regs->smi);
+		if (timeout-- == 0) {
+			printf("Err..(%s) SMI busy timeout\n", __FUNCTION__);
+			return -ETIME;
+		}
+	} while (smi_reg & KWGBE_PHY_SMI_BUSY_MASK);
+
+	/* fill the phy addr and reg offset and write opcode and data */
+	smi_reg = (data << KWGBE_PHY_SMI_DATA_OFFS);
+	smi_reg |= (phy_adr << KWGBE_PHY_SMI_DEV_ADDR_OFFS)
+		| (reg_ofs << KWGBE_SMI_REG_ADDR_OFFS);
+	smi_reg &= ~KWGBE_PHY_SMI_OPCODE_READ;
+
+	/* write the smi register */
+	KWGBEREG_WR(regs->smi, smi_reg);
+
+	return 0;
+}
+
+/* Stop and checks all queues */
+static void stop_queue(u32 * qreg)
+{
+	u32 reg_data;
+
+	reg_data = readl(qreg);
+
+	if (reg_data & 0xFF) {
+		/* Issue stop command for active channels only */
+		writel((reg_data << 8), qreg);
+
+		/* Wait for all queue activity to terminate. */
+		do {
+			/*
+			 * Check port cause register that all queues
+			 * are stopped
+			 */
+			reg_data = readl(qreg);
+		}
+		while (reg_data & 0xFF);
+	}
+}
+
+/*
+ * set_access_control - Config address decode parameters for Ethernet unit
+ *
+ * This function configures the address decode parameters for the Gigabit
+ * Ethernet Controller according the given parameters struct.
+ *
+ * @regs	Register struct pointer.
+ * @param	Address decode parameter struct.
+ */
+static void set_access_control(struct kwgbe_registers *regs,
+				struct kwgbe_winparam *param)
+{
+	u32 access_prot_reg;
+
+	/* Set access control register */
+	access_prot_reg = KWGBEREG_RD(regs->epap);
+	/* clear window permission */
+	access_prot_reg &= (~(3 << (param->win * 2)));
+	access_prot_reg |= (param->access_ctrl << (param->win * 2));
+	KWGBEREG_WR(regs->epap, access_prot_reg);
+
+	/* Set window Size reg (SR) */
+	KWGBEREG_WR(regs->barsz[param->win].size,
+			(((param->size / 0x10000) - 1) << 16));
+
+	/* Set window Base address reg (BA) */
+	KWGBEREG_WR(regs->barsz[param->win].bar,
+			(param->target | param->attrib | param->base_addr));
+	/* High address remap reg (HARR) */
+	if (param->win < 4)
+		KWGBEREG_WR(regs->ha_remap[param->win], param->high_addr);
+
+	/* Base address enable reg (BARER) */
+	if (param->enable == 1)
+		KWGBEREG_BITS_RESET(regs->bare, (1 << param->win));
+	else
+		KWGBEREG_BITS_SET(regs->bare, (1 << param->win));
+}
+
+static void set_dram_access(struct kwgbe_registers *regs)
+{
+	struct kwgbe_winparam win_param;
+	int i;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		/* Set access parameters for DRAM bank i */
+		win_param.win = i;	/* Use Ethernet window i */
+		/* Window target - DDR */
+		win_param.target = KWGBE_TARGET_DRAM;
+		/* Enable full access */
+		win_param.access_ctrl = EWIN_ACCESS_FULL;
+		win_param.high_addr = 0;
+		/* Get bank base */
+		win_param.base_addr = kw_sdram_bar(i);
+		win_param.size = kw_sdram_bs(i);	/* Get bank size */
+		if (win_param.size == 0)
+			win_param.enable = 0;
+		else
+			win_param.enable = 1;	/* Enable the access */
+
+		/* Enable DRAM bank */
+		switch (i) {
+		case 0:
+			win_param.attrib = EBAR_DRAM_CS0;
+			break;
+		case 1:
+			win_param.attrib = EBAR_DRAM_CS1;
+			break;
+		case 2:
+			win_param.attrib = EBAR_DRAM_CS2;
+			break;
+		case 3:
+			win_param.attrib = EBAR_DRAM_CS3;
+			break;
+		default:
+			/* invalide bank, disable access */
+			win_param.enable = 0;
+			win_param.attrib = 0;
+			break;
+		}
+		/* Set the access control for address window(EPAPR) RD/WR */
+		set_access_control(regs, &win_param);
+	}
+}
+
+/*
+ * port_init_mac_tables - Clear all entrance in the UC, SMC and OMC tables
+ *
+ * Go through all the DA filter tables (Unicast, Special Multicast & Other
+ * Multicast) and set each entry to 0.
+ */
+static void port_init_mac_tables(struct kwgbe_registers *regs)
+{
+	int table_index;
+
+	/* Clear DA filter unicast table (Ex_dFUT) */
+	for (table_index = 0; table_index < 4; ++table_index)
+		KWGBEREG_WR(regs->dfut[table_index], 0);
+
+	for (table_index = 0; table_index < 64; ++table_index) {
+		/* Clear DA filter special multicast table (Ex_dFSMT) */
+		KWGBEREG_WR(regs->dfsmt[table_index], 0);
+		/* Clear DA filter other multicast table (Ex_dFOMT) */
+		KWGBEREG_WR(regs->dfomt[table_index], 0);
+	}
+}
+
+/*
+ * port_uc_addr - This function Set the port unicast address table
+ *
+ * This function locates the proper entry in the Unicast table for the
+ * specified MAC nibble and sets its properties according to function
+ * parameters.
+ * This function add/removes MAC addresses from the port unicast address
+ * table.
+ *
+ * @uc_nibble	Unicast MAC Address last nibble.
+ * @option      0 = Add, 1 = remove address.
+ *
+ * RETURN: 1 if output succeeded. 0 if option parameter is invalid.
+ */
+static int port_uc_addr(struct kwgbe_registers *regs, u8 uc_nibble,
+			int option)
+{
+	u32 unicast_reg;
+	u32 tbl_offset;
+	u32 reg_offset;
+
+	/* Locate the Unicast table entry */
+	uc_nibble = (0xf & uc_nibble);
+	/* Register offset from unicast table base */
+	tbl_offset = (uc_nibble / 4);
+	/* Entry offset within the above register */
+	reg_offset = uc_nibble % 4;
+
+	switch (option) {
+	case REJECT_MAC_ADDR:
+		/*
+		 * Clear accepts frame bit at specified unicast
+		 * DA table entry
+		 */
+		unicast_reg = KWGBEREG_RD(regs->dfut[tbl_offset]);
+		unicast_reg &= (0xFF << (8 * reg_offset));
+		KWGBEREG_WR(regs->dfut[tbl_offset], unicast_reg);
+		break;
+	case ACCEPT_MAC_ADDR:
+		/* Set accepts frame bit at unicast DA filter table entry */
+		unicast_reg = KWGBEREG_RD(regs->dfut[tbl_offset]);
+		unicast_reg &= (0xFF << (8 * reg_offset));
+		unicast_reg |= ((0x01 | (RXUQ << 1)) << (8 * reg_offset));
+		KWGBEREG_WR(regs->dfut[tbl_offset], unicast_reg);
+		break;
+	default:
+		return 0;
+	}
+	return 1;
+}
+
+/*
+ * port_uc_addr_set - This function Set the port Unicast address.
+ */
+static void port_uc_addr_set(struct kwgbe_registers *regs, u8 * p_addr)
+{
+	u32 mac_h;
+	u32 mac_l;
+
+	mac_l = (p_addr[4] << 8) | (p_addr[5]);
+	mac_h = (p_addr[0] << 24) | (p_addr[1] << 16) | (p_addr[2] << 8) |
+		(p_addr[3] << 0);
+
+	KWGBEREG_WR(regs->macal, mac_l);
+	KWGBEREG_WR(regs->macah, mac_h);
+
+	/* Accept frames of this address */
+	port_uc_addr(regs, p_addr[5], ACCEPT_MAC_ADDR);
+}
+
+/*
+ * kwgbe_init_rx_desc_ring - Curve a Rx chain desc list and buffer in memory.
+ */
+static void kwgbe_init_rx_desc_ring(struct kwgbe_device *dkwgbe)
+{
+	volatile struct kwgbe_rxdesc *p_rx_desc;
+	int i;
+
+	/* initialize the Rx descriptors ring */
+	p_rx_desc = dkwgbe->p_rxdesc;
+	for (i = 0; i < RINGSZ; i++) {
+		p_rx_desc->cmd_sts =
+			KWGBE_BUFFER_OWNED_BY_DMA | KWGBE_RX_EN_INTERRUPT;
+		p_rx_desc->buf_size = PKTSIZE_ALIGN;
+		p_rx_desc->byte_cnt = 0;
+		p_rx_desc->buf_ptr = dkwgbe->p_rxbuf + i * PKTSIZE_ALIGN;
+		if (i == (RINGSZ - 1))
+			p_rx_desc->nxtdesc_p = dkwgbe->p_rxdesc;
+		else {
+			p_rx_desc->nxtdesc_p = (struct kwgbe_rxdesc *)
+				((u32) p_rx_desc + KW_RXQ_DESC_ALIGNED_SIZE);
+			p_rx_desc = p_rx_desc->nxtdesc_p;
+		}
+	}
+	dkwgbe->p_rxdesc_curr = dkwgbe->p_rxdesc;
+}
+
+static int kwgbe_init(struct eth_device *dev)
+{
+	struct kwgbe_device *dkwgbe = to_dkwgbe(dev);
+	struct kwgbe_registers *regs = dkwgbe->regs;
+
+	/* setup RX rings */
+	kwgbe_init_rx_desc_ring(dkwgbe);
+
+	/* Clear the ethernet port interrupts */
+	KWGBEREG_WR(regs->ic, 0);
+	KWGBEREG_WR(regs->ice, 0);
+	/* Unmask RX buffer and TX end interrupt */
+	KWGBEREG_WR(regs->pim, INT_CAUSE_UNMASK_ALL);
+	/* Unmask phy and link status changes interrupts */
+	KWGBEREG_WR(regs->peim, INT_CAUSE_UNMASK_ALL_EXT);
+
+	set_dram_access(regs);
+	port_init_mac_tables(regs);
+	port_uc_addr_set(regs, dkwgbe->dev.enetaddr);
+
+	/* Assign port configuration and command. */
+	KWGBEREG_WR(regs->pxc, PRT_CFG_VAL);
+	KWGBEREG_WR(regs->pxcx, PORT_CFG_EXTEND_VALUE);
+	KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE);
+	/* Disable port initially */
+	KWGBEREG_BITS_SET(regs->psc0, KWGBE_SERIAL_PORT_EN);
+
+	/* Assign port SDMA configuration */
+	KWGBEREG_WR(regs->sdc, PORT_SDMA_CFG_VALUE);
+	KWGBEREG_WR(regs->tqx[0].qxttbc, QTKNBKT_DEF_VAL);
+	KWGBEREG_WR(regs->tqx[0].tqxtbc, (QMTBS_DEF_VAL << 16) | QTKNRT_DEF_VAL);
+	/* Turn off the port/RXUQ bandwidth limitation */
+	KWGBEREG_WR(regs->pmtu, 0);
+
+	/* Set maximum receive buffer to 9700 bytes */
+	KWGBEREG_WR(regs->psc0,	KWGBE_MAX_RX_PACKET_9700BYTE
+			| (KWGBEREG_RD(regs->psc0) & MRU_MASK));
+
+	/*
+	 * Set ethernet MTU for leaky bucket mechanism to 0 - this will
+	 * disable the leaky bucket mechanism .
+	 */
+	KWGBEREG_WR(regs->pmtu, 0);
+
+	/* Assignment of Rx CRDB of given RXUQ */
+	KWGBEREG_WR(regs->rxcdp[RXUQ].rxcdp, (u32) dkwgbe->p_rxdesc_curr);
+	/* Enable port Rx. */
+	KWGBEREG_WR(regs->rqc, (1 << RXUQ));
+
+#if (defined (CONFIG_MII) || defined (CONFIG_CMD_MII)) \
+	 && defined (CONFIG_SYS_FAULT_ECHO_LINK_DOWN)
+	u16 phyadr;
+	miiphy_read(dev->name, 0xEE, 0xEE, &phyadr);
+	if (!miiphy_link(dev->name, phyadr)) {
+		printf("%s: No link on %s\n", __FUNCTION__, dev->name);
+		return -1;
+	}
+#endif
+	return 0;
+}
+
+static int kwgbe_halt(struct eth_device *dev)
+{
+	struct kwgbe_device *dkwgbe = to_dkwgbe(dev);
+	struct kwgbe_registers *regs = dkwgbe->regs;
+
+	/* Disable all gigE address decoder */
+	KWGBEREG_WR(regs->bare, 0x3f);
+
+	stop_queue(&regs->tqc);
+	stop_queue(&regs->rqc);
+
+	/* Enable port */
+	KWGBEREG_BITS_RESET(regs->psc0, KWGBE_SERIAL_PORT_EN);
+	/* Set port is not reset */
+	KWGBEREG_BITS_RESET(regs->psc1, 1 << 4);
+#ifdef CONFIG_SYS_MII_MODE
+	/* Set MMI interface up */
+	KWGBEREG_BITS_RESET(regs->psc1, 1 << 3);
+#endif
+	/* Disable & mask ethernet port interrupts */
+	KWGBEREG_WR(regs->ic, 0);
+	KWGBEREG_WR(regs->ice, 0);
+	KWGBEREG_WR(regs->pim, 0);
+	KWGBEREG_WR(regs->peim, 0);
+
+	return 0;
+}
+
+static int kwgbe_send(struct eth_device *dev, volatile void *dataptr,
+		      int datasize)
+{
+	struct kwgbe_device *dkwgbe = to_dkwgbe(dev);
+	struct kwgbe_registers *regs = dkwgbe->regs;
+	struct kwgbe_txdesc *p_txdesc = dkwgbe->p_txdesc;
+
+	if ((u32) dataptr & 0x07) {
+		printf("Err..(%s) xmit dataptr not 64bit aligned\n",
+			__FUNCTION__);
+		return -1;
+	}
+	p_txdesc->cmd_sts = KWGBE_ZERO_PADDING | KWGBE_GEN_CRC;
+	p_txdesc->cmd_sts |= KWGBE_TX_FIRST_DESC | KWGBE_TX_LAST_DESC;
+	p_txdesc->cmd_sts |= KWGBE_BUFFER_OWNED_BY_DMA;
+	p_txdesc->cmd_sts |= KWGBE_TX_EN_INTERRUPT;
+	p_txdesc->buf_ptr = (u8 *) dataptr;
+	p_txdesc->byte_cnt = datasize;
+
+	/* Apply send command using zeroth RXUQ */
+	KWGBEREG_WR(regs->tcqdp[TXUQ], (u32) p_txdesc);
+	KWGBEREG_WR(regs->tqc, (1 << TXUQ));
+
+	/*
+	 * wait for packet xmit completion
+	 */
+	while (p_txdesc->cmd_sts & KWGBE_BUFFER_OWNED_BY_DMA) {
+		/* return fail if error is detected */
+		if (p_txdesc->cmd_sts & (KWGBE_UR_ERROR | KWGBE_RL_ERROR)) {
+			printf("Err..(%s) in xmit packet\n", __FUNCTION__);
+			return -1;
+		}
+	};
+	return 0;
+}
+
+static int kwgbe_recv(struct eth_device *dev)
+{
+	volatile struct kwgbe_device *dkwgbe = to_dkwgbe(dev);
+	volatile struct kwgbe_rxdesc *p_rxdesc_curr = dkwgbe->p_rxdesc_curr;
+	volatile u32 timeout = 0;
+
+	/* wait untill rx packet available or timeout */
+	do {
+		if (timeout < KWGBE_PHY_SMI_TIMEOUT)
+			timeout++;
+		else {
+			debug("%s time out...\n", __FUNCTION__);
+			return -1;
+		}
+	} while (p_rxdesc_curr->cmd_sts & KWGBE_BUFFER_OWNED_BY_DMA);
+
+	if (p_rxdesc_curr->byte_cnt != 0) {
+		debug("%s: Received %d byte Packet @ 0x%x (cmd_sts= %08x)\n",
+			__FUNCTION__, (u32) p_rxdesc_curr->byte_cnt,
+			(u32) p_rxdesc_curr->buf_ptr,
+			(u32) p_rxdesc_curr->cmd_sts);
+	}
+
+	/*
+	 * In case received a packet without first/last bits on
+	 * OR the error summary bit is on,
+	 * the packets needs to be dropeed.
+	 */
+	if ((p_rxdesc_curr->cmd_sts &
+		(KWGBE_RX_FIRST_DESC | KWGBE_RX_LAST_DESC))
+		!= (KWGBE_RX_FIRST_DESC | KWGBE_RX_LAST_DESC)) {
+
+		printf("Err..(%s) Dropping packet spread on"
+			" multiple descriptors\n", __FUNCTION__);
+
+	} else if (p_rxdesc_curr->cmd_sts & KWGBE_ERROR_SUMMARY) {
+
+		printf("Err..(%s) Dropping packet with errors\n",
+			__FUNCTION__);
+
+	} else {
+		/* !!! call higher layer processing */
+		debug("%s: Sending Received packet to"
+			" upper layer (NetReceive)\n", __FUNCTION__);
+
+		/* let the upper layer handle the packet */
+		NetReceive((p_rxdesc_curr->buf_ptr + RX_BUF_OFFSET),
+			(int)(p_rxdesc_curr->byte_cnt - RX_BUF_OFFSET));
+	}
+	/*
+	 * free these descriptors and point next in the ring
+	 */
+	p_rxdesc_curr->cmd_sts =
+		KWGBE_BUFFER_OWNED_BY_DMA | KWGBE_RX_EN_INTERRUPT;
+	p_rxdesc_curr->buf_size = PKTSIZE_ALIGN;
+	p_rxdesc_curr->byte_cnt = 0;
+
+	dkwgbe->p_rxdesc_curr = p_rxdesc_curr->nxtdesc_p;
+	return 0;
+}
+
+int kirkwood_egiga_initialize(bd_t * bis)
+{
+	struct kwgbe_device *dkwgbe;
+	struct eth_device *dev;
+	int devnum;
+	char *s, buf[NAMESIZE * 2];
+	u8 used_ports[MAX_KWGBE_DEVS] = CONFIG_KIRKWOOD_EGIGA_PORTS;
+
+	for (devnum = 0; devnum < MAX_KWGBE_DEVS; devnum++) {
+		/*skip if port is configured not to use */
+		if (used_ports[devnum] == 0)
+			continue;
+
+		if (!(dkwgbe = malloc(sizeof(struct kwgbe_device))))
+			goto error1;
+
+		memset(dkwgbe, 0, sizeof(struct kwgbe_device));
+
+		if (!(dkwgbe->p_rxdesc =
+		      (struct kwgbe_rxdesc *)memalign(PKTALIGN,
+						KW_RXQ_DESC_ALIGNED_SIZE
+						* RINGSZ + 1)))
+			goto error2;
+
+		if (!(dkwgbe->p_rxbuf = (u8 *) memalign(PKTALIGN, RINGSZ
+							* PKTSIZE_ALIGN + 1)))
+			goto error3;
+
+		if (!(dkwgbe->p_txdesc = (struct kwgbe_txdesc *)
+		      memalign(PKTALIGN, sizeof(struct kwgbe_txdesc) + 1))) {
+			free(dkwgbe->p_rxbuf);
+		      error3:
+			free(dkwgbe->p_rxdesc);
+		      error2:
+			free(dkwgbe);
+		      error1:
+			printf("Err.. %s Failed to allocate memory\n",
+				__FUNCTION__);
+			return -1;
+		}
+
+		dev = &dkwgbe->dev;
+
+		/* must be less than NAMESIZE (16) */
+		sprintf(dev->name, "egiga%d", devnum);
+
+		/* Extract the MAC address from the environment */
+		switch (devnum) {
+		case 0:
+			dkwgbe->regs = (void *)KW_EGIGA0_BASE;
+			s = "ethaddr";
+			break;
+		case 1:
+			dkwgbe->regs = (void *)KW_EGIGA1_BASE;
+			s = "eth1addr";
+			break;
+		default:	/* this should never happen */
+			printf("Err..(%s) Invalid device number %d\n",
+				__FUNCTION__, devnum);
+			return -1;
+		}
+
+		while (!eth_getenv_enetaddr(s, dev->enetaddr)) {
+			/* Generate Ramdom MAC addresses if not set */
+			sprintf(buf, "00:50:43:%02x:%02x:%02x",
+				get_random_hex(), get_random_hex(),
+				get_random_hex());
+			setenv(s, buf);
+		}
+
+		dev->init = (void *)kwgbe_init;
+		dev->halt = (void *)kwgbe_halt;
+		dev->send = (void *)kwgbe_send;
+		dev->recv = (void *)kwgbe_recv;
+
+		eth_register(dev);
+
+#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
+		miiphy_register(dev->name, smi_reg_read, smi_reg_write);
+		/* Set phy address of the port */
+		miiphy_write(dev->name, 0xEE, 0xEE, PHY_BASE_ADR + devnum);
+#endif
+	}
+	return 0;
diff --git a/drivers/net/kirkwood_egiga.h b/drivers/net/kirkwood_egiga.h
new file mode 100644
index 0000000..8b67c9c
--- /dev/null
+++ b/drivers/net/kirkwood_egiga.h
@@ -0,0 +1,503 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * based on - Driver for MV64360X ethernet ports
+ * Copyright (C) 2002 rabeeh@galileo.co.il
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __EGIGA_H__
+#define __EGIGA_H__
+
+#define MAX_KWGBE_DEVS	2	/*controller has two ports */
+
+/* PHY_BASE_ADR is board specific and can be configured */
+#if defined (CONFIG_PHY_BASE_ADR)
+#define PHY_BASE_ADR		CONFIG_PHY_BASE_ADR
+#else
+#define PHY_BASE_ADR		0x08	/* default phy base addr */
+#endif
+
+/* Constants */
+#define INT_CAUSE_UNMASK_ALL		0x0007ffff
+#define INT_CAUSE_UNMASK_ALL_EXT	0x0011ffff
+#define MRU_MASK			0xfff1ffff
+#define PHYADR_MASK			0x0000001f
+#define PHYREG_MASK			0x0000001f
+#define QTKNBKT_DEF_VAL			0x3fffffff
+#define QMTBS_DEF_VAL			0x000003ff
+#define QTKNRT_DEF_VAL			0x0000fcff
+#define RXUQ	0 /* Used Rx queue */
+#define TXUQ	0 /* Used Rx queue */
+
+#define to_dkwgbe(_kd) container_of(_kd, struct kwgbe_device, dev)
+#define KWGBEREG_WR(adr, val)		writel(val, &adr)
+#define KWGBEREG_RD(adr)		readl(&adr)
+#define KWGBEREG_BITS_RESET(adr, val)	writel(readl(&adr) & ~(val), &adr)
+#define KWGBEREG_BITS_SET(adr, val)	writel(readl(&adr) | val, &adr)
+
+/* Default port configuration value */
+#define PRT_CFG_VAL			( \
+	KWGBE_UCAST_MOD_NRML		| \
+	KWGBE_DFLT_RXQ(RXUQ)		| \
+	KWGBE_DFLT_RX_ARPQ(RXUQ)	| \
+	KWGBE_RX_BC_IF_NOT_IP_OR_ARP	| \
+	KWGBE_RX_BC_IF_IP		| \
+	KWGBE_RX_BC_IF_ARP		| \
+	KWGBE_CPTR_TCP_FRMS_DIS		| \
+	KWGBE_CPTR_UDP_FRMS_DIS		| \
+	KWGBE_DFLT_RX_TCPQ(RXUQ)	| \
+	KWGBE_DFLT_RX_UDPQ(RXUQ)	| \
+	KWGBE_DFLT_RX_BPDUQ(RXUQ))
+
+/* Default port extend configuration value */
+#define PORT_CFG_EXTEND_VALUE		\
+	KWGBE_SPAN_BPDU_PACKETS_AS_NORMAL	| \
+	KWGBE_PARTITION_DIS		| \
+	KWGBE_TX_CRC_GENERATION_EN
+
+#define GT_KWGBE_IPG_INT_RX(value)	((value & 0x3fff) << 8)
+
+/* Default sdma control value */
+#define PORT_SDMA_CFG_VALUE		( \
+	KWGBE_RX_BURST_SIZE_16_64BIT	| \
+	KWGBE_BLM_RX_NO_SWAP		| \
+	KWGBE_BLM_TX_NO_SWAP		| \
+	GT_KWGBE_IPG_INT_RX(RXUQ)	| \
+	KWGBE_TX_BURST_SIZE_16_64BIT)
+
+/* Default port serial control value */
+#define PORT_SERIAL_CONTROL_VALUE		( \
+	KWGBE_FORCE_LINK_PASS			| \
+	KWGBE_DIS_AUTO_NEG_FOR_DUPLX		| \
+	KWGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL	| \
+	KWGBE_ADV_NO_FLOW_CTRL			| \
+	KWGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX	| \
+	KWGBE_FORCE_BP_MODE_NO_JAM		| \
+	(1 << 9) /* Reserved bit has to be 1 */	| \
+	KWGBE_DO_NOT_FORCE_LINK_FAIL		| \
+	KWGBE_EN_AUTO_NEG_SPEED_GMII		| \
+	KWGBE_DTE_ADV_0				| \
+	KWGBE_MIIPHY_MAC_MODE			| \
+	KWGBE_AUTO_NEG_NO_CHANGE		| \
+	KWGBE_MAX_RX_PACKET_1552BYTE		| \
+	KWGBE_CLR_EXT_LOOPBACK			| \
+	KWGBE_SET_FULL_DUPLEX_MODE		| \
+	KWGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX)
+
+/* Tx WRR confoguration macros */
+#define PORT_MAX_TRAN_UNIT	0x24	/* MTU register (default) 9KByte */
+#define PORT_MAX_TOKEN_BUCKET_SIZE	0x_FFFF	/* PMTBS reg (default) */
+#define PORT_TOKEN_RATE		1023	/* PTTBRC reg (default) */
+/* MAC accepet/reject macros */
+#define ACCEPT_MAC_ADDR		0
+#define REJECT_MAC_ADDR		1
+/* Size of a Tx/Rx descriptor used in chain list data structure */
+#define KW_RXQ_DESC_ALIGNED_SIZE	\
+	(((sizeof(struct kwgbe_rxdesc) / PKTALIGN) + 1) * PKTALIGN)
+/* Buffer offset from buffer pointer */
+#define RX_BUF_OFFSET		0x2
+
+/* Port serial status reg (PSR) */
+#define KWGBE_INTERFACE_GMII_MII	0
+#define KWGBE_INTERFACE_PCM		1
+#define KWGBE_LINK_IS_DOWN		0
+#define KWGBE_LINK_IS_UP		(1 << 1)
+#define KWGBE_PORT_AT_HALF_DUPLEX	0
+#define KWGBE_PORT_AT_FULL_DUPLEX	(1 << 2)
+#define KWGBE_RX_FLOW_CTRL_DISD		0
+#define KWGBE_RX_FLOW_CTRL_ENBALED	(1 << 3)
+#define KWGBE_GMII_SPEED_100_10		0
+#define KWGBE_GMII_SPEED_1000		(1 << 4)
+#define KWGBE_MII_SPEED_10		0
+#define KWGBE_MII_SPEED_100		(1 << 5)
+#define KWGBE_NO_TX			0
+#define KWGBE_TX_IN_PROGRESS		(1 << 7)
+#define KWGBE_BYPASS_NO_ACTIVE		0
+#define KWGBE_BYPASS_ACTIVE		(1 << 8)
+#define KWGBE_PORT_NOT_AT_PARTN_STT	0
+#define KWGBE_PORT_AT_PARTN_STT		(1 << 9)
+#define KWGBE_PORT_TX_FIFO_NOT_EMPTY	0
+#define KWGBE_PORT_TX_FIFO_EMPTY	(1 << 10)
+
+/* These macros describes the Port configuration reg (Px_cR) bits */
+#define KWGBE_UCAST_MOD_NRML		0
+#define KWGBE_UNICAST_PROMISCUOUS_MODE	1
+#define KWGBE_DFLT_RXQ(_x)		(_x << 1)
+#define KWGBE_DFLT_RX_ARPQ(_x)		(_x << 4)
+#define KWGBE_RX_BC_IF_NOT_IP_OR_ARP	0
+#define KWGBE_REJECT_BC_IF_NOT_IP_OR_ARP (1 << 7)
+#define KWGBE_RX_BC_IF_IP		0
+#define KWGBE_REJECT_BC_IF_IP		(1 << 8)
+#define KWGBE_RX_BC_IF_ARP		0
+#define KWGBE_REJECT_BC_IF_ARP		(1 << 9)
+#define KWGBE_TX_AM_NO_UPDATE_ERR_SMRY	(1 << 12)
+#define KWGBE_CPTR_TCP_FRMS_DIS		0
+#define KWGBE_CPTR_TCP_FRMS_EN		(1 << 14)
+#define KWGBE_CPTR_UDP_FRMS_DIS		0
+#define KWGBE_CPTR_UDP_FRMS_EN		(1 << 15)
+#define KWGBE_DFLT_RX_TCPQ(_x)		(_x << 16)
+#define KWGBE_DFLT_RX_UDPQ(_x)		(_x << 19)
+#define KWGBE_DFLT_RX_BPDUQ(_x)		(_x << 22)
+#define KWGBE_DFLT_RX_TCP_CHKSUM_MODE	(1 << 25)
+
+/* These macros describes the Port configuration extend reg (Px_cXR) bits*/
+#define KWGBE_CLASSIFY_EN			1
+#define KWGBE_SPAN_BPDU_PACKETS_AS_NORMAL	0
+#define KWGBE_SPAN_BPDU_PACKETS_TO_RX_Q7	(1 << 1)
+#define KWGBE_PARTITION_DIS			0
+#define KWGBE_PARTITION_EN			(1 << 2)
+#define KWGBE_TX_CRC_GENERATION_EN		0
+#define KWGBE_TX_CRC_GENERATION_DIS		(1 << 3)
+
+/* These macros describes the Port Sdma configuration reg (SDCR) bits */
+#define KWGBE_RIFB				1
+#define KWGBE_RX_BURST_SIZE_1_64BIT		0
+#define KWGBE_RX_BURST_SIZE_2_64BIT		(1 << 1)
+#define KWGBE_RX_BURST_SIZE_4_64BIT		(1 << 2)
+#define KWGBE_RX_BURST_SIZE_8_64BIT		((1 << 2) | (1 << 1))
+#define KWGBE_RX_BURST_SIZE_16_64BIT		(1 << 3)
+#define KWGBE_BLM_RX_NO_SWAP			(1 << 4)
+#define KWGBE_BLM_RX_BYTE_SWAP			0
+#define KWGBE_BLM_TX_NO_SWAP			(1 << 5)
+#define KWGBE_BLM_TX_BYTE_SWAP			0
+#define KWGBE_DESCRIPTORS_BYTE_SWAP		(1 << 6)
+#define KWGBE_DESCRIPTORS_NO_SWAP		0
+#define KWGBE_TX_BURST_SIZE_1_64BIT		0
+#define KWGBE_TX_BURST_SIZE_2_64BIT		(1 << 22)
+#define KWGBE_TX_BURST_SIZE_4_64BIT		(1 << 23)
+#define KWGBE_TX_BURST_SIZE_8_64BIT		((1 << 23) | (1 << 22))
+#define KWGBE_TX_BURST_SIZE_16_64BIT		(1 << 24)
+
+/* These macros describes the Port serial control reg (PSCR) bits */
+#define KWGBE_SERIAL_PORT_DIS			0
+#define KWGBE_SERIAL_PORT_EN			1
+#define KWGBE_FORCE_LINK_PASS			(1 << 1)
+#define KWGBE_DO_NOT_FORCE_LINK_PASS		0
+#define KWGBE_EN_AUTO_NEG_FOR_DUPLX		0
+#define KWGBE_DIS_AUTO_NEG_FOR_DUPLX		(1 << 2)
+#define KWGBE_EN_AUTO_NEG_FOR_FLOW_CTRL		0
+#define KWGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL	(1 << 3)
+#define KWGBE_ADV_NO_FLOW_CTRL			0
+#define KWGBE_ADV_SYMMETRIC_FLOW_CTRL		(1 << 4)
+#define KWGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX	0
+#define KWGBE_FORCE_FC_MODE_TX_PAUSE_DIS	(1 << 5)
+#define KWGBE_FORCE_BP_MODE_NO_JAM		0
+#define KWGBE_FORCE_BP_MODE_JAM_TX		(1 << 7)
+#define KWGBE_FORCE_BP_MODE_JAM_TX_ON_RX_ERR	(1 << 8)
+#define KWGBE_FORCE_LINK_FAIL			0
+#define KWGBE_DO_NOT_FORCE_LINK_FAIL		(1 << 10)
+#define KWGBE_DIS_AUTO_NEG_SPEED_GMII		(1 << 13)
+#define KWGBE_EN_AUTO_NEG_SPEED_GMII		0
+#define KWGBE_DTE_ADV_0				0
+#define KWGBE_DTE_ADV_1				(1 << 14)
+#define KWGBE_MIIPHY_MAC_MODE			0
+#define KWGBE_MIIPHY_PHY_MODE			(1 << 15)
+#define KWGBE_AUTO_NEG_NO_CHANGE		0
+#define KWGBE_RESTART_AUTO_NEG			(1 << 16)
+#define KWGBE_MAX_RX_PACKET_1518BYTE		0
+#define KWGBE_MAX_RX_PACKET_1522BYTE		(1 << 17)
+#define KWGBE_MAX_RX_PACKET_1552BYTE		(1 << 18)
+#define KWGBE_MAX_RX_PACKET_9022BYTE		((1 << 18) | (1 << 17))
+#define KWGBE_MAX_RX_PACKET_9192BYTE		(1 << 19)
+#define KWGBE_MAX_RX_PACKET_9700BYTE		((1 << 19) | (1 << 17))
+#define KWGBE_SET_EXT_LOOPBACK			(1 << 20)
+#define KWGBE_CLR_EXT_LOOPBACK			0
+#define KWGBE_SET_FULL_DUPLEX_MODE		(1 << 21)
+#define KWGBE_SET_HALF_DUPLEX_MODE		0
+#define KWGBE_EN_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX	(1 << 22)
+#define KWGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX 0
+#define KWGBE_SET_GMII_SPEED_TO_10_100		0
+#define KWGBE_SET_GMII_SPEED_TO_1000		(1 << 23)
+#define KWGBE_SET_MII_SPEED_TO_10		0
+#define KWGBE_SET_MII_SPEED_TO_100		(1 << 24)
+
+/* SMI register fields */
+#define KWGBE_PHY_SMI_TIMEOUT		10000
+#define KWGBE_PHY_SMI_DATA_OFFS		0	/* Data */
+#define KWGBE_PHY_SMI_DATA_MASK		(0xffff << KWGBE_PHY_SMI_DATA_OFFS)
+#define KWGBE_PHY_SMI_DEV_ADDR_OFFS	16	/* PHY device address */
+#define KWGBE_PHY_SMI_DEV_ADDR_MASK	(PHYADR_MASK << KWGBE_PHY_SMI_DEV_ADDR_OFFS)
+#define KWGBE_SMI_REG_ADDR_OFFS		21	/* PHY device reg addr */
+#define KWGBE_SMI_REG_ADDR_MASK		(PHYADR_MASK << KWGBE_SMI_REG_ADDR_OFFS)
+#define KWGBE_PHY_SMI_OPCODE_OFFS	26	/* Write/Read opcode */
+#define KWGBE_PHY_SMI_OPCODE_MASK	(3 << KWGBE_PHY_SMI_OPCODE_OFFS)
+#define KWGBE_PHY_SMI_OPCODE_WRITE	(0 << KWGBE_PHY_SMI_OPCODE_OFFS)
+#define KWGBE_PHY_SMI_OPCODE_READ	(1 << KWGBE_PHY_SMI_OPCODE_OFFS)
+#define KWGBE_PHY_SMI_READ_VALID_MASK	(1 << 27)	/* Read Valid */
+#define KWGBE_PHY_SMI_BUSY_MASK		(1 << 28)	/* Busy */
+
+/* SDMA command status fields macros */
+/* Tx & Rx descriptors status */
+#define KWGBE_ERROR_SUMMARY		1
+/* Tx & Rx descriptors command */
+#define KWGBE_BUFFER_OWNED_BY_DMA	(1 << 31)
+/* Tx descriptors status */
+#define KWGBE_LC_ERROR			0
+#define KWGBE_UR_ERROR			(1 << 1)
+#define KWGBE_RL_ERROR			(1 << 2)
+#define KWGBE_LLC_SNAP_FORMAT		(1 << 9)
+
+/* Rx descriptors status */
+#define KWGBE_CRC_ERROR			0
+#define KWGBE_OVERRUN_ERROR		(1 << 1)
+#define KWGBE_MAX_FRAME_LENGTH_ERROR	(1 << 2)
+#define KWGBE_RESOURCE_ERROR		((1 << 2) | (1 << 1))
+#define KWGBE_VLAN_TAGGED		(1 << 19)
+#define KWGBE_BPDU_FRAME		(1 << 20)
+#define KWGBE_TCP_FRAME_OVER_IP_V_4	0
+#define KWGBE_UDP_FRAME_OVER_IP_V_4	(1 << 21)
+#define KWGBE_OTHER_FRAME_TYPE		(1 << 22)
+#define KWGBE_LAYER_2_IS_KWGBE_V_2	(1 << 23)
+#define KWGBE_FRAME_TYPE_IP_V_4		(1 << 24)
+#define KWGBE_FRAME_HEADER_OK		(1 << 25)
+#define KWGBE_RX_LAST_DESC		(1 << 26)
+#define KWGBE_RX_FIRST_DESC		(1 << 27)
+#define KWGBE_UNKNOWN_DESTINATION_ADDR	(1 << 28)
+#define KWGBE_RX_EN_INTERRUPT		(1 << 29)
+#define KWGBE_LAYER_4_CHECKSUM_OK	(1 << 30)
+
+/* Rx descriptors byte count */
+#define KWGBE_FRAME_FRAGMENTED		(1 << 2)
+
+/* Tx descriptors command */
+#define KWGBE_LAYER_4_CHECKSUM_FIRST_DESC	(1 << 10)
+#define KWGBE_FRAME_SET_TO_VLAN			(1 << 15)
+#define KWGBE_TCP_FRAME				0
+#define KWGBE_UDP_FRAME				(1 << 16)
+#define KWGBE_GEN_TCP_UDP_CHECKSUM		(1 << 17)
+#define KWGBE_GEN_IP_V_4_CHECKSUM		(1 << 18)
+#define KWGBE_ZERO_PADDING			(1 << 19)
+#define KWGBE_TX_LAST_DESC			(1 << 20)
+#define KWGBE_TX_FIRST_DESC			(1 << 21)
+#define KWGBE_GEN_CRC				(1 << 22)
+#define KWGBE_TX_EN_INTERRUPT			(1 << 23)
+#define KWGBE_AUTO_MODE				(1 << 30)
+
+/* Address decode parameters */
+/* Ethernet Base Address Register bits */
+#define EBAR_TARGET_DRAM			0x00000000
+#define EBAR_TARGET_DEVICE			0x00000001
+#define EBAR_TARGET_CBS				0x00000002
+#define EBAR_TARGET_PCI0			0x00000003
+#define EBAR_TARGET_PCI1			0x00000004
+#define EBAR_TARGET_CUNIT			0x00000005
+#define EBAR_TARGET_AUNIT			0x00000006
+#define EBAR_TARGET_GUNIT			0x00000007
+
+/* Window attrib */
+#define EBAR_DRAM_CS0				0x00000E00
+#define EBAR_DRAM_CS1				0x00000D00
+#define EBAR_DRAM_CS2				0x00000B00
+#define EBAR_DRAM_CS3				0x00000700
+
+/* DRAM Target interface */
+#define EBAR_DRAM_NO_CACHE_COHERENCY		0x00000000
+#define EBAR_DRAM_CACHE_COHERENCY_WT		0x00001000
+#define EBAR_DRAM_CACHE_COHERENCY_WB		0x00002000
+
+/* Device Bus Target interface */
+#define EBAR_DEVICE_DEVCS0			0x00001E00
+#define EBAR_DEVICE_DEVCS1			0x00001D00
+#define EBAR_DEVICE_DEVCS2			0x00001B00
+#define EBAR_DEVICE_DEVCS3			0x00001700
+#define EBAR_DEVICE_BOOTCS3			0x00000F00
+
+/* PCI Target interface */
+#define EBAR_PCI_BYTE_SWAP			0x00000000
+#define EBAR_PCI_NO_SWAP			0x00000100
+#define EBAR_PCI_BYTE_WORD_SWAP			0x00000200
+#define EBAR_PCI_WORD_SWAP			0x00000300
+#define EBAR_PCI_NO_SNOOP_NOT_ASSERT		0x00000000
+#define EBAR_PCI_NO_SNOOP_ASSERT		0x00000400
+#define EBAR_PCI_IO_SPACE			0x00000000
+#define EBAR_PCI_MEMORY_SPACE			0x00000800
+#define EBAR_PCI_REQ64_FORCE			0x00000000
+#define EBAR_PCI_REQ64_SIZE			0x00001000
+
+/* Window access control */
+#define EWIN_ACCESS_NOT_ALLOWED 0
+#define EWIN_ACCESS_READ_ONLY	1
+#define EWIN_ACCESS_FULL	((1 << 1) | 1)
+
+/* structures represents Controller registers */
+struct kwgbe_barsz {
+	u32 bar;
+	u32 size;
+};
+
+struct kwgbe_rxcdp {
+	struct kwgbe_rxdesc *rxcdp;
+	u32 rxcdp_pad[3];
+};
+
+struct kwgbe_tqx {
+	u32 qxttbc;
+	u32 tqxtbc;
+	u32 tqxac;
+	u32 tqxpad;
+};
+
+struct kwgbe_registers {
+	u32 phyadr;
+	u32 smi;
+	u32 euda;
+	u32 eudid;
+	u8 pad1[0x080 - 0x00c - 4];
+	u32 euic;
+	u32 euim;
+	u8 pad2[0x094 - 0x084 - 4];
+	u32 euea;
+	u32 euiae;
+	u8 pad3[0x0b0 - 0x098 - 4];
+	u32 euc;
+	u8 pad3a[0x200 - 0x0b0 - 4];
+	struct kwgbe_barsz barsz[6];
+	u8 pad4[0x280 - 0x22c - 4];
+	u32 ha_remap[4];
+	u32 bare;
+	u32 epap;
+	u8 pad5[0x400 - 0x294 - 4];
+	u32 pxc;
+	u32 pxcx;
+	u32 mii_ser_params;
+	u8 pad6[0x410 - 0x408 - 4];
+	u32 evlane;
+	u32 macal;
+	u32 macah;
+	u32 sdc;
+	u32 dscp[7];
+	u32 psc0;
+	u32 vpt2p;
+	u32 ps0;
+	u32 tqc;
+	u32 psc1;
+	u32 ps1;
+	u32 mrvl_header;
+	u8 pad7[0x460 - 0x454 - 4];
+	u32 ic;
+	u32 ice;
+	u32 pim;
+	u32 peim;
+	u8 pad8[0x474 - 0x46c - 4];
+	u32 pxtfut;
+	u32 pad9;
+	u32 pxmfs;
+	u32 pad10;
+	u32 pxdfc;
+	u32 pxofc;
+	u8 pad11[0x494 - 0x488 - 4];
+	u32 peuiae;
+	u8 pad12[0x4bc - 0x494 - 4];
+	u32 eth_type_prio;
+	u8 pad13[0x4dc - 0x4bc - 4];
+	u32 tqfpc;
+	u32 pttbrc;
+	u32 tqc1;
+	u32 pmtu;
+	u32 pmtbs;
+	u8 pad14[0x60c - 0x4ec - 4];
+	struct kwgbe_rxcdp rxcdp[7];
+	u32 rxcdp7;
+	u32 rqc;
+	struct kwgbe_txdesc *tcsdp;
+	u8 pad15[0x6c0 - 0x684 - 4];
+	struct kwgbe_txdesc *tcqdp[8];
+	u8 pad16[0x700 - 0x6dc - 4];
+	struct kwgbe_tqx tqx[8];
+	u32 pttbc;
+	u8 pad17[0x7a8 - 0x780 - 4];
+	u32 tqxipg0;
+	u32 pad18[3];
+	u32 tqxipg1;
+	u8 pad19[0x7c0 - 0x7b8 - 4];
+	u32 hitkninlopkt;
+	u32 hitkninasyncpkt;
+	u32 lotkninasyncpkt;
+	u32 pad20;
+	u32 ts;
+	u8 pad21[0x3000 - 0x27d0 - 4];
+	u32 pad20_1[32];	/* mib counter registes */
+	u8 pad22[0x3400 - 0x3000 - sizeof(u32) * 32];
+	u32 dfsmt[64];
+	u32 dfomt[64];
+	u32 dfut[4];
+	u8 pad23[0xe20c0 - 0x7360c - 4];
+	u32 pmbus_top_arbiter;
+};
+
+/* structures/enums needed by driver */
+enum kwgbe_adrwin {
+	KWGBE_WIN0,
+	KWGBE_WIN1,
+	KWGBE_WIN2,
+	KWGBE_WIN3,
+	KWGBE_WIN4,
+	KWGBE_WIN5
+};
+
+enum kwgbe_target {
+	KWGBE_TARGET_DRAM,
+	KWGBE_TARGET_DEV,
+	KWGBE_TARGET_CBS,
+	KWGBE_TARGET_PCI0,
+	KWGBE_TARGET_PCI1
+};
+
+struct kwgbe_winparam {
+	enum kwgbe_adrwin win;	/* Window number */
+	enum kwgbe_target target;	/* System targets */
+	u16 attrib;		/* BAR attrib. See above macros */
+	u32 base_addr;		/* Window base address in u32 form */
+	u32 high_addr;		/* Window high address in u32 form */
+	u32 size;		/* Size in MBytes. Must be % 64Kbyte. */
+	int enable;		/* Enable/disable access to the window. */
+	u16 access_ctrl;	/*Access ctrl register. see above macros */
+};
+
+struct kwgbe_rxdesc {
+	u32 cmd_sts;		/* Descriptor command status */
+	u16 buf_size;		/* Buffer size */
+	u16 byte_cnt;		/* Descriptor buffer byte count */
+	u8 *buf_ptr;		/* Descriptor buffer pointer */
+	struct kwgbe_rxdesc *nxtdesc_p;	/* Next descriptor pointer */
+};
+
+struct kwgbe_txdesc {
+	u32 cmd_sts;		/* Descriptor command status */
+	u16 l4i_chk;		/* CPU provided TCP Checksum */
+	u16 byte_cnt;		/* Descriptor buffer byte count */
+	u8 *buf_ptr;		/* Descriptor buffer ptr */
+	struct kwgbe_txdesc *nxtdesc_p;	/* Next descriptor ptr */
+};
+
+/* port device data struct */
+struct kwgbe_device {
+	struct eth_device dev;
+	struct kwgbe_registers *regs;
+	struct kwgbe_txdesc *p_txdesc;
+	struct kwgbe_rxdesc *p_rxdesc;
+	struct kwgbe_rxdesc *p_rxdesc_curr;
+	u8 *p_rxbuf;
+};
+
+#endif /* __EGIGA_H__ */
diff --git a/drivers/net/mcfmii.c b/drivers/net/mcfmii.c
index 4f1c0a0..4acc29e 100644
--- a/drivers/net/mcfmii.c
+++ b/drivers/net/mcfmii.c
@@ -270,7 +270,7 @@ void __mii_init(void)
 		if ((status & linkgood) == linkgood)
 			break;
 
-		udelay(500);
+		udelay(1);
 	}
 	if (i >= MCFFEC_TOUT_LOOP) {
 		printf("Link UP timeout\n");
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 4fe3b05..3b92614 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -26,6 +26,7 @@ include $(TOPDIR)/config.mk
 LIB	:= $(obj)libphy.a
 
 COBJS-$(CONFIG_BITBANGMII) += miiphybb.o
+COBJS-$(CONFIG_MV88E61XX_SWITCH) += mv88e61xx.o
 
 COBJS	:= $(COBJS-y)
 SRCS	:= $(COBJS:.o=.c)
diff --git a/drivers/net/phy/mv88e61xx.c b/drivers/net/phy/mv88e61xx.c
new file mode 100644
index 0000000..ec47286
--- /dev/null
+++ b/drivers/net/phy/mv88e61xx.c
@@ -0,0 +1,413 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include "mv88e61xx.h"
+
+#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE
+/* Chip Address mode
+ * The Switch support two modes of operation
+ * 1. single chip mode and
+ * 2. Multi-chip mode
+ * Refer section 9.2 &9.3 in chip datasheet-02 for more details
+ *
+ * By default single chip mode is configured
+ * multichip mode operation can be configured in board header
+ */
+static int mv88e61xx_busychk_multic(u32 devaddr)
+{
+	u32 reg = 0;
+	u32 timeout = MV88E61XX_PHY_TIMEOUT;
+
+	/* Poll till SMIBusy bit is clear */
+	do {
+		miiphy_read(name, devaddr, 0x0, &reg);
+		if (timeout-- == 0) {
+			printf("SMI busy timeout\n");
+			return -1;
+		}
+	} while (reg & (1 << 15));
+	return 0;
+}
+
+static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data)
+{
+	u16 reg;
+	u32 mii_dev_addr;
+
+	/* command to read PHY dev address */
+	if (!miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
+		printf("Error..could not read PHY dev address\n");
+		return;
+	}
+	mv88e61xx_busychk_multic(mii_dev_addr);
+	/* Write data to Switch indirect data register */
+	miiphy_write(name, mii_dev_addr, 0x1, data);
+	/* Write command to Switch indirect command register (write) */
+	miiphy_write(name, mii_dev_addr, 0x0,
+		     reg_ofs | (phy_adr << 5) | (1 << 10) | (1 << 12) | (1 <<
+									 15));
+}
+
+static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data)
+{
+	u16 reg;
+	u32 mii_dev_addr;
+
+	/* command to read PHY dev address */
+	if (!miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
+		printf("Error..could not read PHY dev address\n");
+		return;
+	}
+	mv88e61xx_busychk_multic(mii_dev_addr);
+	/* Write command to Switch indirect command register (read) */
+	miiphy_write(name, mii_dev_addr, 0x0,
+		     reg_ofs | (phy_adr << 5) | (1 << 10) | (1 << 12) | (1 <<
+									 15));
+	mv88e61xx_busychk_multic(mii_dev_addr);
+	/* Read data from Switch indirect data register */
+	miiphy_read(name, mii_dev_addr, 0x1, (u16 *) & data);
+}
+#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */
+
+static void mv88e61xx_port_vlan_config(struct mv88e61xx_config *swconfig,
+				       u32 max_prtnum, u32 ports_ofs)
+{
+	u32 prt;
+	u16 reg;
+	char *name = swconfig->name;
+	u32 cpu_port = swconfig->cpuport;
+	u32 port_mask = swconfig->ports_enabled;
+	enum mv88e61xx_cfg_vlan vlancfg = swconfig->vlancfg;
+
+	/* be sure all ports are disabled */
+	for (prt = 0; prt < max_prtnum; prt++) {
+		RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, &reg);
+		reg &= ~0x3;
+		WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, reg);
+
+		if (!(cpu_port & (1 << prt)))
+			continue;
+		/* Set CPU port VID to 0x1 */
+		RD_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, &reg);
+		reg &= ~0xfff;
+		reg |= 0x1;
+		WR_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, reg);
+	}
+
+	/* Setting  Port default priority for all ports to zero */
+	for (prt = 0; prt < max_prtnum; prt++) {
+		RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, &reg);
+		reg &= ~0xc000;
+		WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, reg);
+	}
+	/* Setting VID and VID map for all ports except CPU port */
+	for (prt = 0; prt < max_prtnum; prt++) {
+		/* only for enabled ports */
+		if ((1 << prt) & port_mask) {
+			/* skip CPU port */
+			if ((1 << prt) & cpu_port) {
+				/*
+				 * Set Vlan map table for cpu_port to see
+				 * all ports
+				 */
+				RD_PHY(name, (ports_ofs + prt),
+				       MV88E61XX_PRT_VMAP_REG, &reg);
+				reg &= ~((1 << max_prtnum) - 1);
+				reg |= port_mask & ~(1 << prt);
+				WR_PHY(name, (ports_ofs + prt),
+				       MV88E61XX_PRT_VMAP_REG, reg);
+			} else {
+
+				/*
+				 *  set Ports VLAN Mapping.
+				 *      port prt <--> cpu_port VLAN #prt+1.
+				 */
+				RD_PHY(name, ports_ofs + prt,
+				       MV88E61XX_PRT_VID_REG, &reg);
+				reg &= ~0x0fff;
+				reg |= (prt + 1);
+				WR_PHY(name, ports_ofs + prt,
+				       MV88E61XX_PRT_VID_REG, reg);
+
+				RD_PHY(name, ports_ofs + prt,
+				       MV88E61XX_PRT_VMAP_REG, &reg);
+				if (vlancfg == MV88E61XX_VLANCFG_DEFAULT) {
+					/*
+					 * all any port can send frames to all other ports
+					 * ref: sec 3.2.1.1 of datasheet
+					 */
+					reg |= 0x03f;
+					reg &= ~(1 << prt);
+				} else if (vlancfg == MV88E61XX_VLANCFG_ROUTER) {
+					/*
+					 * all other ports can send frames to CPU port only
+					 * ref: sec 3.2.1.2 of datasheet
+					 */
+					reg &= ~((1 << max_prtnum) - 1);
+					reg |= cpu_port;
+				}
+				WR_PHY(name, ports_ofs + prt,
+				       MV88E61XX_PRT_VMAP_REG, reg);
+			}
+		}
+	}
+
+	/*
+	 * enable only appropriate ports to forwarding mode
+	 * and disable the others
+	 */
+	for (prt = 0; prt < max_prtnum; prt++) {
+		if ((1 << prt) & port_mask) {
+			RD_PHY(name, ports_ofs + prt,
+			       MV88E61XX_PRT_CTRL_REG, &reg);
+			reg |= 0x3;
+			WR_PHY(name, ports_ofs + prt,
+			       MV88E61XX_PRT_CTRL_REG, reg);
+		} else {
+			/* Disable port */
+			RD_PHY(name, ports_ofs + prt,
+			       MV88E61XX_PRT_CTRL_REG, &reg);
+			reg &= ~0x3;
+			WR_PHY(name, ports_ofs + prt,
+			       MV88E61XX_PRT_CTRL_REG, reg);
+		}
+	}
+}
+
+/*
+ * Make sure SMIBusy bit cleared before another
+ * SMI operation can take place
+ */
+static int mv88e61xx_busychk(char *name)
+{
+	u32 reg = 0;
+	u32 timeout = MV88E61XX_PHY_TIMEOUT;
+	do {
+		RD_PHY(name, MV88E61XX_GLB2REG_DEVADR,
+		       MV88E61XX_PHY_CMD, (u16 *) & reg);
+		if (timeout-- == 0) {
+			printf("SMI busy timeout\n");
+			return -1;
+		}
+	} while (reg & 1 << 28);	/* busy mask */
+	return 0;
+}
+
+/*
+ * Power up the specified port and reset PHY
+ */
+static int mv88361xx_powerup(struct mv88e61xx_config *swconfig, u32 prt)
+{
+	char *name = swconfig->name;
+
+	/* Write Copper Specific control reg1 (0x14) for-
+	 * Enable Phy power up
+	 * Energy Detect on (sense&Xmit NLP Periodically
+	 * reset other settings default
+	 */
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x3360);
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
+	       MV88E61XX_PHY_CMD, (0x9410 | (prt << 5)));
+
+	if (mv88e61xx_busychk(name))
+		return -1;
+
+	/* Write PHY ctrl reg (0x0) to apply
+	 * Phy reset (set bit 15 low)
+	 * reset other default values
+	 */
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x1140);
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
+	       MV88E61XX_PHY_CMD, (0x9400 | (prt << 5)));
+
+	if (mv88e61xx_busychk(name))
+		return -1;
+
+	return 0;
+}
+
+/*
+ * Default Setup for LED[0]_Control (ref: Table 46 Datasheet-3)
+ * is set to "On-1000Mb/s Link, Off Else"
+ * This function sets it to "On-Link, Blink-Activity, Off-NoLink"
+ *
+ * This is optional settings may be needed on some boards
+ * to setup PHY LEDs default configuration to detect 10/100/1000Mb/s
+ * Link status
+ */
+static int mv88361xx_led_init(struct mv88e61xx_config *swconfig, u32 prt)
+{
+	char *name = swconfig->name;
+	u16 reg;
+
+	if (swconfig->led_init != MV88E61XX_LED_INIT_EN)
+		return 0;
+
+	/* set page address to 3 */
+	reg = 3;
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
+	       MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
+				   1 << MV88E61XX_MODE_OFST |
+				   1 << MV88E61XX_OP_OFST |
+				   prt << MV88E61XX_ADDR_OFST | 22));
+
+	if (mv88e61xx_busychk(name))
+		return -1;
+
+	/* set LED Func Ctrl reg */
+	reg = 1;	/* LED[0] On-Link, Blink-Activity, Off-NoLink */
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
+	       MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
+				   1 << MV88E61XX_MODE_OFST |
+				   1 << MV88E61XX_OP_OFST |
+				   prt << MV88E61XX_ADDR_OFST | 16));
+
+	if (mv88e61xx_busychk(name))
+		return -1;
+
+	/* set page address to 0 */
+	reg = 0;
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
+	       MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
+				   1 << MV88E61XX_MODE_OFST |
+				   1 << MV88E61XX_OP_OFST |
+				   prt << MV88E61XX_ADDR_OFST | 22));
+
+	if (mv88e61xx_busychk(name))
+		return -1;
+
+	return 0;
+}
+
+/*
+ * Reverse Transmit polarity for Media Dependent Interface
+ * Pins (MDIP) bits in Copper Specific Control Register 3
+ * (Page 0, Reg 20 for each phy (except cpu port)
+ * Reference: Section 1.1 Switch datasheet-3
+ *
+ * This is optional settings may be needed on some boards
+ * for PHY<->magnetics h/w tuning
+ */
+static int mv88361xx_reverse_mdipn(struct mv88e61xx_config *swconfig, u32 prt)
+{
+	char *name = swconfig->name;
+	u16 reg;
+
+	if (swconfig->mdip != MV88E61XX_MDIP_REVERSE)
+		return 0;
+
+	reg = 0x0f;		/*Reverse MDIP/N[3:0] bits */
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
+	WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
+	       MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
+				   1 << MV88E61XX_MODE_OFST |
+				   1 << MV88E61XX_OP_OFST |
+				   prt << MV88E61XX_ADDR_OFST | 20));
+
+	if (mv88e61xx_busychk(name))
+		return -1;
+
+	return 0;
+}
+
+/*
+ * Marvell 88E61XX Switch initialization
+ */
+int mv88e61xx_switch_initialize(struct mv88e61xx_config *swconfig)
+{
+	u32 prt;
+	u16 reg;
+	char *idstr;
+	char *name = swconfig->name;
+
+	if (miiphy_set_current_dev(name)) {
+		printf("%s failed\n", __FUNCTION__);
+		return -1;
+	}
+
+	if (!(swconfig->cpuport & ((1 << 4) | (1 << 5)))) {
+		swconfig->cpuport = (1 << 5);
+		printf("Invalid cpu port config, using default port5\n");
+	}
+
+	RD_PHY(name, MV88E61XX_PRT_OFST, PHY_PHYIDR2, &reg);
+	reg &= 0xfff0;
+	if (reg == 0x1610)
+		idstr = "88E6161";
+	if (reg == 0x1650)
+		idstr = "88E6165";
+	if (reg == 0x1210) {
+		idstr = "88E6123";
+		/* ports 2,3,4 not available */
+		swconfig->ports_enabled &= 0x023;
+	}
+
+	/* Port based VLANs configuration */
+	if ((swconfig->vlancfg == MV88E61XX_VLANCFG_DEFAULT)
+	    || (swconfig->vlancfg == MV88E61XX_VLANCFG_ROUTER))
+		mv88e61xx_port_vlan_config(swconfig, MV88E61XX_MAX_PORTS_NUM,
+					   MV88E61XX_PRT_OFST);
+	else {
+		printf("Unsupported mode %s failed\n", __FUNCTION__);
+		return -1;
+	}
+
+	if (swconfig->rgmii_delay == MV88E61XX_RGMII_DELAY_EN) {
+		/*
+		 * Enable RGMII delay on Tx and Rx for CPU port
+		 * Ref: sec 9.5 of chip datasheet-02
+		 */
+		WR_PHY(name, MV88E61XX_PRT_OFST + 5,
+		       MV88E61XX_RGMII_TIMECTRL_REG, 0x18);
+		WR_PHY(name, MV88E61XX_PRT_OFST + 4,
+		       MV88E61XX_RGMII_TIMECTRL_REG, 0xc1e7);
+	}
+
+	for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) {
+		if (!((1 << prt) & swconfig->cpuport)) {
+
+			if (mv88361xx_led_init(swconfig, prt))
+				return -1;
+			if (mv88361xx_reverse_mdipn(swconfig, prt))
+				return -1;
+			if (mv88361xx_powerup(swconfig, prt))
+				return -1;
+		}
+
+		/*Program port state */
+		RD_PHY(name, MV88E61XX_PRT_OFST + prt,
+		       MV88E61XX_PRT_CTRL_REG, &reg);
+		WR_PHY(name, MV88E61XX_PRT_OFST + prt,
+		       MV88E61XX_PRT_CTRL_REG,
+		       reg | (swconfig->portstate & 0x03));
+	}
+
+	printf("%s Initialized on %s\n", idstr, name);
+	return 0;
+}
diff --git a/drivers/net/phy/mv88e61xx.h b/drivers/net/phy/mv88e61xx.h
new file mode 100644
index 0000000..4279464
--- /dev/null
+++ b/drivers/net/phy/mv88e61xx.h
@@ -0,0 +1,62 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _MV88E61XX_H
+#define _MV88E61XX_H
+
+#include <miiphy.h>
+
+#define MV88E61XX_CPU_PORT		0x5
+#define MV88E61XX_MAX_PORTS_NUM		0x6
+
+#define MV88E61XX_PHY_TIMEOUT		100000
+
+#define MV88E61XX_PRT_STS_REG		0x1
+#define MV88E61XX_PRT_CTRL_REG		0x4
+#define MV88E61XX_PRT_VMAP_REG		0x6
+#define MV88E61XX_PRT_VID_REG		0x7
+
+#define MV88E61XX_PRT_OFST		0x10
+#define MV88E61XX_PHY_CMD		0x18
+#define MV88E61XX_PHY_DATA		0x19
+#define MV88E61XX_RGMII_TIMECTRL_REG	0x1A
+#define MV88E61XX_GLB2REG_DEVADR	0x1C
+
+#define MV88E61XX_BUSY_OFST		15
+#define MV88E61XX_MODE_OFST		12
+#define MV88E61XX_OP_OFST			10
+#define MV88E61XX_ADDR_OFST		5
+
+#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE
+static int mv88e61xx_busychk_multic(u32 devaddr);
+static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data);
+static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data);
+#define WR_PHY mv88e61xx_wr_phy
+#define RD_PHY mv88e61xx_rd_phy
+#else
+#define WR_PHY miiphy_write
+#define RD_PHY miiphy_read
+#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */
+
+#endif /* _MV88E61XX_H */
diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c
index 399116f..63fc02e 100644
--- a/drivers/net/tsec.c
+++ b/drivers/net/tsec.c
@@ -468,6 +468,18 @@ uint mii_parse_link(uint mii_reg, struct tsec_private *priv)
 }
 
 /*
+ * "Ethernet@Wirespeed" needs to be enabled to achieve link in certain
+ * circumstances.  eg a gigabit TSEC connected to a gigabit switch with
+ * a 4-wire ethernet cable.  Both ends advertise gigabit, but can't
+ * link.  "Ethernet@Wirespeed" reduces advertised speed until link
+ * can be achieved.
+ */
+uint mii_BCM54xx_wirespeed(uint mii_reg, struct tsec_private *priv)
+{
+	return (read_phy_reg(priv, mii_reg) & 0x8FFF) | 0x8010;
+}
+
+/*
  * Parse the BCM54xx status register for speed and duplex information.
  * The linux sungem_phy has this information, but in a table format.
  */
@@ -1070,6 +1082,34 @@ struct phy_info phy_info_BCM5464S = {
 	},
 };
 
+struct phy_info phy_info_BCM5482S =  {
+	0x0143bcb,
+	"Broadcom BCM5482S",
+	4,
+	(struct phy_cmd[]) { /* config */
+		/* Reset and configure the PHY */
+		{MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},
+		/* Setup read from auxilary control shadow register 7 */
+		{MIIM_BCM54xx_AUXCNTL, MIIM_BCM54xx_AUXCNTL_ENCODE(7), NULL},
+		/* Read Misc Control register and or in Ethernet@Wirespeed */
+		{MIIM_BCM54xx_AUXCNTL, 0, &mii_BCM54xx_wirespeed},
+		{MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init},
+		{miim_end,}
+	},
+	(struct phy_cmd[]) { /* startup */
+		/* Status is read once to clear old link state */
+		{MIIM_STATUS, miim_read, NULL},
+		/* Auto-negotiate */
+		{MIIM_STATUS, miim_read, &mii_parse_sr},
+		/* Read the status */
+		{MIIM_BCM54xx_AUXSTATUS, miim_read, &mii_parse_BCM54xx_sr},
+		{miim_end,}
+	},
+	(struct phy_cmd[]) { /* shutdown */
+		{miim_end,}
+	},
+};
+
 struct phy_info phy_info_M88E1011S = {
 	0x01410c6,
 	"Marvell 88E1011S",
@@ -1611,6 +1651,7 @@ struct phy_info *phy_info[] = {
 	&phy_info_cis8201,
 	&phy_info_BCM5461S,
 	&phy_info_BCM5464S,
+	&phy_info_BCM5482S,
 	&phy_info_M88E1011S,
 	&phy_info_M88E1111S,
 	&phy_info_M88E1118,
diff --git a/include/asm-arm/arch-davinci/emac_defs.h b/include/asm-arm/arch-davinci/emac_defs.h
index c11161f..ae75f84 100644
--- a/include/asm-arm/arch-davinci/emac_defs.h
+++ b/include/asm-arm/arch-davinci/emac_defs.h
@@ -38,15 +38,38 @@
 
 #include <asm/arch/hardware.h>
 
+#ifdef CONFIG_SOC_DM365
+#define EMAC_BASE_ADDR			(0x01d07000)
+#define EMAC_WRAPPER_BASE_ADDR		(0x01d0a000)
+#define EMAC_WRAPPER_RAM_ADDR		(0x01d08000)
+#define EMAC_MDIO_BASE_ADDR		(0x01d0b000)
+#else
 #define EMAC_BASE_ADDR			(0x01c80000)
 #define EMAC_WRAPPER_BASE_ADDR		(0x01c81000)
 #define EMAC_WRAPPER_RAM_ADDR		(0x01c82000)
 #define EMAC_MDIO_BASE_ADDR		(0x01c84000)
+#endif
 
+#ifdef CONFIG_SOC_DM646x
+/* MDIO module input frequency */
+#define EMAC_MDIO_BUS_FREQ		76500000
+/* MDIO clock output frequency */
+#define EMAC_MDIO_CLOCK_FREQ		2500000		/* 2.5 MHz */
+#elif defined(CONFIG_SOC_DM365)
+/* MDIO module input frequency */
+#define EMAC_MDIO_BUS_FREQ		121500000
+/* MDIO clock output frequency */
+#define EMAC_MDIO_CLOCK_FREQ		2200000		/* 2.2 MHz */
+#else
 /* MDIO module input frequency */
 #define EMAC_MDIO_BUS_FREQ		99000000	/* PLL/6 - 99 MHz */
 /* MDIO clock output frequency */
 #define EMAC_MDIO_CLOCK_FREQ		2000000		/* 2.0 MHz */
+#endif
+
+/* PHY mask - set only those phy number bits where phy is/can be connected */
+#define EMAC_MDIO_PHY_NUM           1
+#define EMAC_MDIO_PHY_MASK          (1 << EMAC_MDIO_PHY_NUM)
 
 /* Ethernet Min/Max packet size */
 #define EMAC_MIN_ETHERNET_PKT_SIZE	60
@@ -103,6 +126,8 @@ typedef volatile struct _emac_desc
 
 #define EMAC_MACCONTROL_MIIEN_ENABLE		(0x20)
 #define EMAC_MACCONTROL_FULLDUPLEX_ENABLE	(0x1)
+#define EMAC_MACCONTROL_GIGABIT_ENABLE		(1 << 7)
+#define EMAC_MACCONTROL_GIGFORCE		(1 << 17)
 
 #define EMAC_RXMBPENABLE_RXCAFEN_ENABLE	(0x200000)
 #define EMAC_RXMBPENABLE_RXBROADEN	(0x2000)
@@ -258,12 +283,17 @@ typedef struct  {
 
 /* EMAC Wrapper Registers Structure */
 typedef struct  {
+#if defined(CONFIG_SOC_DM646x) || defined(CONFIG_SOC_DM365)
+	dv_reg		IDVER;
+	dv_reg		SOFTRST;
+	dv_reg		EMCTRL;
+#else
 	u_int8_t	RSVD0[4100];
 	dv_reg		EWCTL;
 	dv_reg		EWINTTCNT;
+#endif
 } ewrap_regs;
 
-
 /* EMAC MDIO Registers Structure */
 typedef struct  {
 	dv_reg		VERSION;
diff --git a/include/configs/M5253DEMO.h b/include/configs/M5253DEMO.h
index 1fea6c3..50b3a03 100644
--- a/include/configs/M5253DEMO.h
+++ b/include/configs/M5253DEMO.h
@@ -88,6 +88,7 @@
 #	define _IO_BASE			0
 #endif
 
+#define CONFIG_NET_MULTI		1
 #define CONFIG_DRIVER_DM9000
 #ifdef CONFIG_DRIVER_DM9000
 #	define CONFIG_DM9000_BASE	(CONFIG_SYS_CS1_BASE | 0x300)
diff --git a/include/configs/at91sam9261ek.h b/include/configs/at91sam9261ek.h
index 4f6b640..83e05b3 100644
--- a/include/configs/at91sam9261ek.h
+++ b/include/configs/at91sam9261ek.h
@@ -131,6 +131,7 @@
 #define CONFIG_SYS_NO_FLASH			1
 
 /* Ethernet */
+#define CONFIG_NET_MULTI		1
 #define CONFIG_DRIVER_DM9000		1
 #define CONFIG_DM9000_BASE		0x30000000
 #define DM9000_IO			CONFIG_DM9000_BASE
diff --git a/include/configs/davinci_dvevm.h b/include/configs/davinci_dvevm.h
index 6c5d065..96b6afc 100644
--- a/include/configs/davinci_dvevm.h
+++ b/include/configs/davinci_dvevm.h
@@ -109,6 +109,7 @@
 #define CONFIG_BOOTP_DNS2
 #define CONFIG_BOOTP_SEND_HOSTNAME
 #define CONFIG_NET_RETRY_COUNT	10
+#define CONFIG_NET_MULTI
 /*=====================*/
 /* Flash & Environment */
 /*=====================*/
diff --git a/include/configs/davinci_schmoogie.h b/include/configs/davinci_schmoogie.h
index 6612cb3..9cb9838 100644
--- a/include/configs/davinci_schmoogie.h
+++ b/include/configs/davinci_schmoogie.h
@@ -77,6 +77,7 @@
 #define CONFIG_BOOTP_SEND_HOSTNAME
 #define CONFIG_NET_RETRY_COUNT	10
 #define CONFIG_OVERWRITE_ETHADDR_ONCE
+#define CONFIG_NET_MULTI
 /*=====================*/
 /* Flash & Environment */
 /*=====================*/
diff --git a/include/configs/davinci_sffsdr.h b/include/configs/davinci_sffsdr.h
index 6c1dc11..a47620f 100644
--- a/include/configs/davinci_sffsdr.h
+++ b/include/configs/davinci_sffsdr.h
@@ -74,6 +74,7 @@
 #define CONFIG_BOOTP_SEND_HOSTNAME
 #define CONFIG_NET_RETRY_COUNT	10
 #define CONFIG_OVERWRITE_ETHADDR_ONCE
+#define CONFIG_NET_MULTI
 /* Flash & Environment */
 #undef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_SYS_NO_FLASH
diff --git a/include/configs/davinci_sonata.h b/include/configs/davinci_sonata.h
index 893729c..82901b3 100644
--- a/include/configs/davinci_sonata.h
+++ b/include/configs/davinci_sonata.h
@@ -109,6 +109,7 @@
 #define CONFIG_BOOTP_DNS2
 #define CONFIG_BOOTP_SEND_HOSTNAME
 #define CONFIG_NET_RETRY_COUNT	10
+#define CONFIG_NET_MULTI
 /*=====================*/
 /* Flash & Environment */
 /*=====================*/
diff --git a/include/configs/scb9328.h b/include/configs/scb9328.h
index 893c3d3..5556714 100644
--- a/include/configs/scb9328.h
+++ b/include/configs/scb9328.h
@@ -255,6 +255,7 @@
 #define CONFIG_SYS_CS5U_VAL 0x00008400
 #define CONFIG_SYS_CS5L_VAL 0x00000D03
 
+#define CONFIG_NET_MULTI		1
 #define CONFIG_DRIVER_DM9000		1
 #define CONFIG_DM9000_BASE		0x16000000
 #define DM9000_IO			CONFIG_DM9000_BASE
diff --git a/include/configs/trizepsiv.h b/include/configs/trizepsiv.h
index 49045fd..bfa7157 100644
--- a/include/configs/trizepsiv.h
+++ b/include/configs/trizepsiv.h
@@ -278,6 +278,7 @@
 #define CONFIG_SYS_MCIO0_VAL		0x00008407
 #define CONFIG_SYS_MCIO1_VAL		0x0000c108
 
+#define CONFIG_NET_MULTI		1
 #define CONFIG_DRIVER_DM9000		1
 #define CONFIG_DM9000_BASE	0x08000000
 #define DM9000_IO			CONFIG_DM9000_BASE
diff --git a/include/netdev.h b/include/netdev.h
index 63cf730..aed5c4c 100644
--- a/include/netdev.h
+++ b/include/netdev.h
@@ -44,6 +44,7 @@ int cpu_eth_init(bd_t *bis);
 int au1x00_enet_initialize(bd_t*);
 int bfin_EMAC_initialize(bd_t *bis);
 int dc21x4x_initialize(bd_t *bis);
+int davinci_emac_initialize(void);
 int dnet_eth_initialize(int id, void *regs, unsigned int phy_addr);
 int e1000_initialize(bd_t *bis);
 int eepro100_initialize(bd_t *bis);
@@ -52,6 +53,7 @@ int fec_initialize (bd_t *bis);
 int greth_initialize(bd_t *bis);
 void gt6426x_eth_initialize(bd_t *bis);
 int inca_switch_initialize(bd_t *bis);
+int kirkwood_egiga_initialize(bd_t *bis);
 int macb_eth_initialize(int id, void *regs, unsigned int phy_addr);
 int mcdmafec_initialize(bd_t *bis);
 int mcffec_initialize(bd_t *bis);
@@ -73,6 +75,7 @@ int tsi108_eth_initialize(bd_t *bis);
 int uec_initialize(int index);
 int uli526x_initialize(bd_t *bis);
 int sh_eth_initialize(bd_t *bis);
+int dm9000_initialize(bd_t *bis);
 
 /* Boards with PCI network controllers can call this from their board_eth_init()
  * function to initialize whatever's on board.
@@ -116,4 +119,51 @@ static inline int pci_eth_init(bd_t *bis)
 	return num;
 }
 
+/*
+ * Boards with mv88e61xx switch can use this by defining
+ * CONFIG_MV88E61XX_SWITCH in respective board configheader file
+ * the stuct and enums here are used to specify switch configuration params
+ */
+#if defined(CONFIG_MV88E61XX_SWITCH)
+enum mv88e61xx_cfg_vlan {
+	MV88E61XX_VLANCFG_DEFAULT,
+	MV88E61XX_VLANCFG_ROUTER
+};
+
+enum mv88e61xx_cfg_mdip {
+	MV88E61XX_MDIP_NOCHANGE,
+	MV88E61XX_MDIP_REVERSE
+};
+
+enum mv88e61xx_cfg_ledinit {
+	MV88E61XX_LED_INIT_DIS,
+	MV88E61XX_LED_INIT_EN
+};
+
+enum mv88e61xx_cfg_rgmiid {
+	MV88E61XX_RGMII_DELAY_DIS,
+	MV88E61XX_RGMII_DELAY_EN
+};
+
+enum mv88e61xx_cfg_prtstt {
+	MV88E61XX_PORTSTT_DISABLED,
+	MV88E61XX_PORTSTT_BLOCKING,
+	MV88E61XX_PORTSTT_LEARNING,
+	MV88E61XX_PORTSTT_FORWARDING
+};
+
+struct mv88e61xx_config {
+	char *name;
+	enum mv88e61xx_cfg_vlan vlancfg;
+	enum mv88e61xx_cfg_rgmiid rgmii_delay;
+	enum mv88e61xx_cfg_prtstt portstate;
+	enum mv88e61xx_cfg_ledinit led_init;
+	enum mv88e61xx_cfg_mdip mdip;
+	u32 ports_enabled;
+	u8 cpuport;
+};
+
+int mv88e61xx_switch_initialize(struct mv88e61xx_config *swconfig);
+#endif /* CONFIG_MV88E61XX_SWITCH */
+
 #endif /* _NETDEV_H_ */
diff --git a/include/tsec.h b/include/tsec.h
index 9184256..0ac3034 100644
--- a/include/tsec.h
+++ b/include/tsec.h
@@ -152,6 +152,8 @@
 #define MIIM_EXT_PAGE_ACCESS	0x1f
 
 /* Broadcom BCM54xx -- taken from linux sungem_phy */
+#define MIIM_BCM54xx_AUXCNTL			0x18
+#define MIIM_BCM54xx_AUXCNTL_ENCODE(val)	((val & 0x7) << 12)|(val & 0x7)
 #define MIIM_BCM54xx_AUXSTATUS			0x19
 #define MIIM_BCM54xx_AUXSTATUS_LINKMODE_MASK	0x0700
 #define MIIM_BCM54xx_AUXSTATUS_LINKMODE_SHIFT	8
diff --git a/net/bootp.c b/net/bootp.c
index 3dea70aa..77057c6 100644
--- a/net/bootp.c
+++ b/net/bootp.c
@@ -687,7 +687,7 @@ BootpRequest (void)
 	 * Calculate proper packet lengths taking into account the
 	 * variable size of the options field
 	 */
-	pktlen = BOOTP_SIZE - sizeof(bp->bp_vend) + ext_len;
+	pktlen = ((int)(pkt-NetTxPacket)) + BOOTP_HDR_SIZE - sizeof(bp->bp_vend) + ext_len;
 	iplen = BOOTP_HDR_SIZE - sizeof(bp->bp_vend) + ext_len;
 	NetSetIP(iphdr, 0xFFFFFFFFL, PORT_BOOTPS, PORT_BOOTPC, iplen);
 	NetSetTimeout(SELECT_TIMEOUT, BootpTimeout);
@@ -860,7 +860,7 @@ static void DhcpSendRequestPkt(Bootp_t *bp_offer)
 	NetCopyIP(&OfferedIP, &bp_offer->bp_yiaddr);
 	extlen = DhcpExtended((u8 *)bp->bp_vend, DHCP_REQUEST, NetDHCPServerIP, OfferedIP);
 
-	pktlen = BOOTP_SIZE - sizeof(bp->bp_vend) + extlen;
+	pktlen = ((int)(pkt-NetTxPacket)) + BOOTP_HDR_SIZE - sizeof(bp->bp_vend) + extlen;
 	iplen = BOOTP_HDR_SIZE - sizeof(bp->bp_vend) + extlen;
 	NetSetIP(iphdr, 0xFFFFFFFFL, PORT_BOOTPS, PORT_BOOTPC, iplen);
 
diff --git a/net/eth.c b/net/eth.c
index 8940ebf..3d93966 100644
--- a/net/eth.c
+++ b/net/eth.c
@@ -501,10 +501,8 @@ char *eth_get_name (void)
 #elif defined(CONFIG_CMD_NET) && !defined(CONFIG_NET_MULTI)
 
 extern int at91rm9200_miiphy_initialize(bd_t *bis);
-extern int emac4xx_miiphy_initialize(bd_t *bis);
 extern int mcf52x2_miiphy_initialize(bd_t *bis);
 extern int ns7520_miiphy_initialize(bd_t *bis);
-extern int davinci_eth_miiphy_initialize(bd_t *bis);
 
 
 int eth_initialize(bd_t *bis)
@@ -516,18 +514,12 @@ int eth_initialize(bd_t *bis)
 #if defined(CONFIG_AT91RM9200)
 	at91rm9200_miiphy_initialize(bis);
 #endif
-#if defined(CONFIG_PPC4xx_EMAC)
-	emac4xx_miiphy_initialize(bis);
-#endif
 #if defined(CONFIG_MCF52x2)
 	mcf52x2_miiphy_initialize(bis);
 #endif
 #if defined(CONFIG_DRIVER_NS7520_ETHERNET)
 	ns7520_miiphy_initialize(bis);
 #endif
-#if defined(CONFIG_DRIVER_TI_EMAC)
-	davinci_eth_miiphy_initialize(bis);
-#endif
 	return 0;
 }
 #endif