Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/master

170 files changed, 6790 insertions, 9323 deletions

diff --git a/MAINTAINERS b/MAINTAINERS
index 2f61776..b0da631 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -462,10 +462,11 @@ Rune Torgersen <runet@innovsys.com>
 
 Peter Tyser <ptyser@xes-inc.com>
 
-	XPEDITE1000	PPC440GX
-	XPEDITE5170	MPC8640
-	XPEDITE5200	MPC8548
-	XPEDITE5370	MPC8572
+	xpedite1000	PPC440GX
+	xpedite5170	MPC8640
+	xpedite5200	MPC8548
+	xpedite5370	MPC8572
+	xpedite5500	P2020
 
 David Updegraff <dave@cray.com>
 
diff --git a/MAKEALL b/MAKEALL
index 51312dd..8ad7e92 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -554,9 +554,7 @@ LIST_mips_el="			\
 ## i386 Systems
 #########################################################################
 
-LIST_x86="$(boards_by_arch i386)
-	sc520_eNET	\
-"
+LIST_x86="$(boards_by_arch i386)"
 
 #########################################################################
 ## Nios-II Systems
@@ -609,31 +607,11 @@ LIST_blackfin="$(boards_by_arch blackfin)
 ## SH Systems
 #########################################################################
 
-LIST_sh2="		\
-	rsk7203		\
-"
-LIST_sh3="		\
-	mpr2		\
-	ms7720se	\
-"
-
-LIST_sh4="		\
-	ms7750se	\
-	ms7722se	\
-	MigoR		\
-	r7780mp		\
-	r2dplus		\
-	sh7763rdp	\
-	sh7785lcr	\
-	ap325rxa	\
-	espt		\
-"
+LIST_sh2="$(boards_by_cpu sh2)"
+LIST_sh3="$(boards_by_cpu sh3)"
+LIST_sh4="$(boards_by_cpu sh4)"
 
-LIST_sh="		\
-	${LIST_sh2}	\
-	${LIST_sh3}	\
-	${LIST_sh4}	\
-"
+LIST_sh="$(boards_by_arch sh)"
 
 #########################################################################
 ## SPARC Systems
diff --git a/Makefile b/Makefile
index 06c71a2..f8e13d7 100644
--- a/Makefile
+++ b/Makefile
@@ -1184,88 +1184,6 @@ bf527-ezkit-v2_config	: unconfig
 	@$(MKCONFIG) -t BF527_EZKIT_REV_2_1 \
 		bf527-ezkit blackfin blackfin bf527-ezkit
 
-#========================================================================
-# SH3 (SuperH)
-#========================================================================
-
-#########################################################################
-## sh2 (Renesas SuperH)
-#########################################################################
-rsk7203_config: unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_RSK7203 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh2 rsk7203 renesas
-
-#########################################################################
-## sh3 (Renesas SuperH)
-#########################################################################
-
-mpr2_config: unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_MPR2 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh3 mpr2
-
-ms7720se_config: unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_MS7720SE 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh3 ms7720se
-
-#########################################################################
-## sh4 (Renesas SuperH)
-#########################################################################
-
-MigoR_config :       unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_MIGO_R 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh4 MigoR renesas
-
-ms7750se_config: unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_MS7750SE 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh4 ms7750se
-
-ms7722se_config :	unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_MS7722SE 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh4 ms7722se
-
-r2dplus_config  :   unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_R2DPLUS 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh4 r2dplus renesas
-
-r7780mp_config: unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_R7780MP 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh4 r7780mp renesas
-
-sh7763rdp_config  :   unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_SH7763RDP 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh4 sh7763rdp renesas
-
-sh7785lcr_32bit_config \
-sh7785lcr_config  :   unconfig
-	@mkdir -p $(obj)include
-	@mkdir -p $(obj)board/renesas/sh7785lcr
-	@echo "#define CONFIG_SH7785LCR 1" > $(obj)include/config.h
-	@if [ "$(findstring 32bit, $@)" ] ; then \
-		echo "#define CONFIG_SH_32BIT 1" >> $(obj)include/config.h ; \
-		echo "CONFIG_SYS_TEXT_BASE = 0x8ff80000" > \
-			$(obj)board/renesas/sh7785lcr/config.tmp ; \
-	fi
-	@$(MKCONFIG) -n $@ -a sh7785lcr sh sh4 sh7785lcr renesas
-
-ap325rxa_config  :   unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_AP325RXA 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh4 ap325rxa renesas
-
-espt_config  :   unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_ESPT 1" > $(obj)include/config.h
-	@$(MKCONFIG) -a $@ sh sh4 espt
-
 #########################################################################
 #########################################################################
 
diff --git a/arch/arm/cpu/pxa/start.S b/arch/arm/cpu/pxa/start.S
index 684e44e..3c5bd84 100644
--- a/arch/arm/cpu/pxa/start.S
+++ b/arch/arm/cpu/pxa/start.S
@@ -8,6 +8,7 @@
  *  Copyright (C) 2002	Kyle Harris <kharris@nexus-tech.net>
  *  Copyright (C) 2003	Robert Schwebel <r.schwebel@pengutronix.de>
  *  Copyright (C) 2003	Kai-Uwe Bloem <kai-uwe.bloem@auerswald.de>
+ *  Copyright (c) 2010	Marek Vasut <marek.vasut@gmail.com>
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -94,20 +95,16 @@ _fiq:			.word fiq
 _TEXT_BASE:
 	.word	CONFIG_SYS_TEXT_BASE
 
-.globl _armboot_start
-_armboot_start:
-	.word _start
-
 /*
  * These are defined in the board-specific linker script.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -127,30 +124,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual reset code
  */
@@ -272,9 +245,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -288,36 +260,54 @@ copy_loop:
 	ldmfd sp!, {r0-r12}
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]	/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23		/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2		/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8	/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
-	bne	fixloop
+	blo	fixloop
 #endif
 #endif	/* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
@@ -332,24 +322,33 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
  * initialization, now running from RAM.
  */
 #ifdef CONFIG_ONENAND_IPL
-	ldr     pc, _start_oneboot
+	ldr     r0, _start_oneboot_ofs
+	mov	pc, r0
 
-_start_oneboot: .word start_oneboot
+_start_oneboot_ofs
+	: .word start_oneboot
 #else
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	r0, r0, r1
+	add	lr, r0, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
 #endif
 
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
+
 #else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
 
 /****************************************************************************/
@@ -567,13 +566,7 @@ fiq:
 /*									    */
 /****************************************************************************/
 /* Operating System Timer */
-OSTIMER_BASE:	.word	0x40a00000
-#define OSMR3	0x0C
-#define OSCR	0x10
-#define OWER	0x18
-#define OIER	0x1C
-
-	.align	5
+.align	5
 .globl reset_cpu
 
 	/* FIXME: this code is PXA250 specific. How is this handled on	    */
@@ -583,18 +576,20 @@ reset_cpu:
 
 	/* We set OWE:WME (watchdog enable) and wait until timeout happens  */
 
-	ldr	r0, OSTIMER_BASE
-	ldr	r1, [r0, #OWER]
+	ldr	r0, =OWER
+	ldr	r1, [r0]
 	orr	r1, r1, #0x0001			/* bit0: WME		    */
-	str	r1, [r0, #OWER]
+	str	r1, [r0]
 
 	/* OS timer does only wrap every 1165 seconds, so we have to set    */
 	/* the match register as well.					    */
 
-	ldr	r1, [r0, #OSCR]			/* read OS timer	    */
+	ldr	r0, =OSCR
+	ldr	r1, [r0]			/* read OS timer	    */
 	add	r1, r1, #0x800			/* let OSMR3 match after    */
 	add	r1, r1, #0x800			/* 4096*(1/3.6864MHz)=1ms   */
-	str	r1, [r0, #OSMR3]
+	ldr	r0, =OSMR3
+	str	r1, [r0]
 
 reset_endless:
 
diff --git a/arch/arm/cpu/pxa/u-boot.lds b/arch/arm/cpu/pxa/u-boot.lds
index 74a4c6e..d6643f9 100644
--- a/arch/arm/cpu/pxa/u-boot.lds
+++ b/arch/arm/cpu/pxa/u-boot.lds
@@ -41,21 +41,18 @@ SECTIONS
 	. = ALIGN(4);
 	.data : {
 		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
+	__rel_dyn_start = .;
+	.rel.dyn : { *(.rel.dyn) }
+	__rel_dyn_end = .;
+
+	__dynsym_start = .;
+	.dynsym : { *(.dynsym) }
+
+	. = ALIGN(4);
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
diff --git a/arch/arm/include/asm/arch-mx5/crm_regs.h b/arch/arm/include/asm/arch-mx5/crm_regs.h
index 14aa231..4ed8eb3 100644
--- a/arch/arm/include/asm/arch-mx5/crm_regs.h
+++ b/arch/arm/include/asm/arch-mx5/crm_regs.h
@@ -189,4 +189,15 @@ struct mxc_ccm_reg {
 #define MXC_CCM_CSCDR1_UART_CLK_PODF_OFFSET		0
 #define MXC_CCM_CSCDR1_UART_CLK_PODF_MASK		0x7
 
+/* Define the bits in register CCDR */
+#define MXC_CCM_CCDR_IPU_HS_MASK			(0x1 << 17)
+
+/* Define the bits in register CCGRx */
+#define MXC_CCM_CCGR_CG_MASK				0x3
+
+#define MXC_CCM_CCGR5_CG5_OFFSET			10
+
+/* Define the bits in register CLPCR */
+#define MXC_CCM_CLPCR_BYPASS_IPU_LPM_HS                 (0x1 << 18)
+
 #endif				/* __ARCH_ARM_MACH_MX51_CRM_REGS_H__ */
diff --git a/arch/arm/lib/board.c b/arch/arm/lib/board.c
index ffe261b..af9a414 100644
--- a/arch/arm/lib/board.c
+++ b/arch/arm/lib/board.c
@@ -716,6 +716,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 #if defined(CONFIG_CMD_I2C)
 	i2c_reloc();
 #endif
+#if defined(CONFIG_CMD_ONENAND)
+	onenand_reloc();
+#endif
 #endif /* !defined(CONFIG_RELOC_FIXUP_WORKS) */
 
 #ifdef CONFIG_LOGBUFFER
diff --git a/arch/sh/config.mk b/arch/sh/config.mk
index 07ba68f..415c949 100644
--- a/arch/sh/config.mk
+++ b/arch/sh/config.mk
@@ -29,6 +29,6 @@ STANDALONE_LOAD_ADDR += -EB
 endif
 
 PLATFORM_CPPFLAGS += -DCONFIG_SH -D__SH__
-PLATFORM_LDFLAGS += -e $(CONFIG_SYS_TEXT_BASE) --defsym reloc_dst=$(TEXT_BASE)
+PLATFORM_LDFLAGS += -e $(CONFIG_SYS_TEXT_BASE) --defsym reloc_dst=$(CONFIG_SYS_TEXT_BASE)
 
 LDSCRIPT := $(SRCTREE)/$(CPUDIR)/u-boot.lds
diff --git a/arch/sh/lib/bootm.c b/arch/sh/lib/bootm.c
index 9c58ed7..f38d0b0 100644
--- a/arch/sh/lib/bootm.c
+++ b/arch/sh/lib/bootm.c
@@ -43,6 +43,41 @@ static void hexdump(unsigned char *buf, int len)
 }
 #endif
 
+#define MOUNT_ROOT_RDONLY	0x000
+#define RAMDISK_FLAGS		0x004
+#define ORIG_ROOT_DEV		0x008
+#define LOADER_TYPE			0x00c
+#define INITRD_START		0x010
+#define INITRD_SIZE			0x014
+#define COMMAND_LINE		0x100
+
+#define RD_PROMPT	(1<<15)
+#define RD_DOLOAD	(1<<14)
+#define CMD_ARG_RD_PROMPT	"prompt_ramdisk="
+#define CMD_ARG_RD_DOLOAD	"load_ramdisk="
+
+#ifdef CONFIG_SH_SDRAM_OFFSET
+#define GET_INITRD_START(initrd, linux) (initrd - linux + CONFIG_SH_SDRAM_OFFSET)
+#else
+#define GET_INITRD_START(initrd, linux) (initrd - linux)
+#endif
+
+static void set_sh_linux_param(unsigned long param_addr, unsigned long data)
+{
+	*(unsigned long *)(param_addr) = data;
+}
+
+static unsigned long sh_check_cmd_arg(char *cmdline, char *key, int base)
+{
+	unsigned long val = 0;
+	char *p = strstr(cmdline, key);
+	if (p) {
+		p += strlen(key);
+		val = simple_strtol(p, NULL, base);
+	}
+	return val;
+}
+
 int do_bootm_linux(int flag, int argc, char * const argv[], bootm_headers_t *images)
 {
 	/* Linux kernel load address */
@@ -51,7 +86,7 @@ int do_bootm_linux(int flag, int argc, char * const argv[], bootm_headers_t *ima
 	unsigned char *param
 		= (unsigned char *)image_get_load(images->legacy_hdr_os);
 	/* Linux kernel command line */
-	char *cmdline = (char *)param + 0x100;
+	char *cmdline = (char *)param + COMMAND_LINE;
 	/* PAGE_SIZE */
 	unsigned long size = images->ep - (unsigned long)param;
 	char *bootargs = getenv("bootargs");
@@ -61,8 +96,37 @@ int do_bootm_linux(int flag, int argc, char * const argv[], bootm_headers_t *ima
 
 	/* Setup parameters */
 	memset(param, 0, size);	/* Clear zero page */
+
+	/* Set commandline */
 	strcpy(cmdline, bootargs);
 
+	sh_check_cmd_arg(bootargs, CMD_ARG_RD_DOLOAD, 10);
+	/* Initrd */
+	if (images->rd_start || images->rd_end) {
+		unsigned long ramdisk_flags = 0;
+		int val = sh_check_cmd_arg(bootargs, CMD_ARG_RD_PROMPT, 10);
+		if (val == 1)
+				ramdisk_flags |= RD_PROMPT;
+		else
+				ramdisk_flags &= ~RD_PROMPT;
+					
+		val = sh_check_cmd_arg(bootargs, CMD_ARG_RD_DOLOAD, 10);
+		if (val == 1)
+				ramdisk_flags |= RD_DOLOAD;
+		else
+				ramdisk_flags &= ~RD_DOLOAD;
+
+		set_sh_linux_param((unsigned long)param + MOUNT_ROOT_RDONLY, 0x0001);
+		set_sh_linux_param((unsigned long)param + RAMDISK_FLAGS, ramdisk_flags);
+		set_sh_linux_param((unsigned long)param + ORIG_ROOT_DEV, 0x0200);
+		set_sh_linux_param((unsigned long)param + LOADER_TYPE, 0x0001);
+		set_sh_linux_param((unsigned long)param + INITRD_START,
+			GET_INITRD_START(images->rd_start, CONFIG_SYS_SDRAM_BASE));
+		set_sh_linux_param((unsigned long)param + INITRD_SIZE,
+			images->rd_end - images->rd_start);
+	}
+
+	/* Boot kernel */
 	kernel();
 	/* does not return */
 
diff --git a/board/a4m072/a4m072.c b/board/a4m072/a4m072.c
index ae7ccbb..09a5a51 100644
--- a/board/a4m072/a4m072.c
+++ b/board/a4m072/a4m072.c
@@ -270,8 +270,6 @@ static u8 display_buf[DISPLAY_BUF_SIZE];
 static u8 display_putc_pos;
 static u8 display_out_pos;
 
-static u8 display_dot_enable;
-
 void display_set(int cmd) {
 
 	if (cmd & DISPLAY_CLEAR) {
@@ -281,12 +279,6 @@ void display_set(int cmd) {
 	if (cmd & DISPLAY_HOME) {
 		display_putc_pos = 0;
 	}
-
-	if (cmd & DISPLAY_MARK) {
-		display_dot_enable = 1;
-	} else {
-		display_dot_enable = 0;
-	}
 }
 
 #define SEG_A    (1<<0)
@@ -314,10 +306,12 @@ void display_set(int cmd) {
  * A..Z		index 10..35
  * -		index 36
  * _		index 37
+ * .		index 38
  */
 
 #define SYMBOL_DASH		(36)
 #define SYMBOL_UNDERLINE	(37)
+#define SYMBOL_DOT		(38)
 
 static u8 display_char2seg7_tbl[]=
 {
@@ -337,28 +331,29 @@ static u8 display_char2seg7_tbl[]=
 	SEG_B | SEG_C | SEG_D | SEG_E | SEG_G,			/* d */
 	SEG_A | SEG_D | SEG_E | SEG_F | SEG_G,			/* E */
 	SEG_A | SEG_E | SEG_F | SEG_G,				/* F */
-	SEG_A | SEG_B | SEG_C | SEG_D | SEG_F | SEG_G,		/* g */
+	0,					/* g - not displayed */
 	SEG_B | SEG_C | SEG_E | SEG_F | SEG_G,			/* H */
-	SEG_E | SEG_F,						/* I */
-	SEG_B | SEG_C | SEG_D | SEG_E,				/* J */
-	SEG_A,						/* K - special 1 */
+	SEG_B | SEG_C,						/* I */
+	0,					/* J - not displayed */
+	0,					/* K - not displayed */
 	SEG_D | SEG_E | SEG_F,					/* L */
-	SEG_B,						/* m - special 2 */
-	SEG_C | SEG_E | SEG_G,					/* n */
-	SEG_C | SEG_D | SEG_E | SEG_G,				/* o */
+	0,					/* m - not displayed */
+	0,					/* n - not displayed */
+	SEG_A | SEG_B | SEG_C | SEG_D | SEG_E | SEG_F,		/* O */
 	SEG_A | SEG_B | SEG_E | SEG_F | SEG_G,			/* P */
-	SEG_A | SEG_B | SEG_C | SEG_F | SEG_G,			/* q */
-	SEG_E | SEG_G,						/* r */
+	0,					/* q - not displayed */
+	0,					/* r - not displayed */
 	SEG_A | SEG_C | SEG_D | SEG_F | SEG_G,			/* S */
 	SEG_D | SEG_E | SEG_F | SEG_G,				/* t */
 	SEG_B | SEG_C | SEG_D | SEG_E | SEG_F,			/* U */
-	SEG_C | SEG_D | SEG_E | SEG_F,				/* V */
-	SEG_C,						/* w - special 3 */
-	SEG_B | SEG_C | SEG_E | SEG_F | SEG_G,			/* X */
+	0,					/* V - not displayed */
+	0,					/* w - not displayed */
+	0,					/* X - not displayed */
 	SEG_B | SEG_C | SEG_D | SEG_F | SEG_G,			/* Y */
-	SEG_A | SEG_B | SEG_D | SEG_E | SEG_G,			/* Z */
+	0,					/* Z - not displayed */
 	SEG_G,							/* - */
-	SEG_D							/* _ */
+	SEG_D,							/* _ */
+	SEG_P							/* . */
 };
 
 /* Convert char to the LED segments representation */
@@ -374,23 +369,20 @@ static u8 display_char2seg7(char c)
 		c -= 'A' - 10;
 	else if (c == '-')
 		c = SYMBOL_DASH;
-	else if ((c == '_') || (c == '.'))
+	else if (c == '_')
 		c = SYMBOL_UNDERLINE;
+	else if (c == '.')
+		c = SYMBOL_DOT;
 	else
 		c = ' ';	/* display unsupported symbols as space */
 
 	if (c != ' ')
 		val = display_char2seg7_tbl[(int)c];
 
-	/* Handle DP LED here */
-	if (display_dot_enable) {
-		val |= SEG_P;
-	}
-
 	return val;
 }
 
-static inline int display_putc_nomark(char c)
+int display_putc(char c)
 {
 	if (display_putc_pos >= DISPLAY_BUF_SIZE)
 		return -1;
@@ -403,13 +395,6 @@ static inline int display_putc_nomark(char c)
 	return c;
 }
 
-int display_putc(char c)
-{
-	/* Mark the codes from the "display" command with the DP LED */
-	display_set(DISPLAY_MARK);
-	return display_putc_nomark(c);
-}
-
 /*
  * Flush current symbol to the LED display hardware
  */
@@ -493,9 +478,8 @@ void show_boot_progress(int status)
 	if (a4m072_status2code(status, buf) < 0)
 		return;
 
-	display_set(0);	/* Clear DP Led */
-	display_putc_nomark(buf[0]);
-	display_putc_nomark(buf[1]);
+	display_putc(buf[0]);
+	display_putc(buf[1]);
 	display_set(DISPLAY_HOME);
 	display_out_pos = 0;	/* reset output position */
 
diff --git a/board/cerf250/Makefile b/board/cerf250/Makefile
index a806b18..b111b51 100644
--- a/board/cerf250/Makefile
+++ b/board/cerf250/Makefile
@@ -26,17 +26,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= cerf250.o flash.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/cerf250/cerf250.c b/board/cerf250/cerf250.c
index 59346bc..043afea 100644
--- a/board/cerf250/cerf250.c
+++ b/board/cerf250/cerf250.c
@@ -39,8 +39,9 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int board_init (void)
 {
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
 
 	/* arch number of cerf PXA Board */
 	gd->bd->bi_arch_number = MACH_TYPE_PXA_CERF;
@@ -58,19 +59,18 @@ int board_late_init(void)
 	return 0;
 }
 
+extern void pxa_dram_init(void);
+int dram_init(void)
+{
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
 
-int dram_init (void)
+void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
-	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
-	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
-
-	return 0;
 }
 
 #ifdef CONFIG_CMD_NET
diff --git a/board/cerf250/config.mk b/board/cerf250/config.mk
deleted file mode 100644
index c2d46b2..0000000
--- a/board/cerf250/config.mk
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# Cerf board with PXA250 cpu
-#
-#
-CONFIG_SYS_TEXT_BASE = 0xa3080000
diff --git a/board/cerf250/lowlevel_init.S b/board/cerf250/lowlevel_init.S
deleted file mode 100644
index 5bfe53c..0000000
--- a/board/cerf250/lowlevel_init.S
+++ /dev/null
@@ -1,411 +0,0 @@
-/*
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * NOTE: I haven't clean this up considerably, just enough to get it
- * running. See hal_platform_setup.h for the source. See
- * board/cradle/lowlevel_init.S for another PXA250 setup that is
- * much cleaner.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-/* wait for coprocessor write complete */
-   .macro CPWAIT reg
-   mrc  p15,0,\reg,c2,c0,0
-   mov  \reg,\reg
-   sub  pc,pc,#4
-   .endm
-
-
-/*
- *	Memory setup
- */
-
-.globl lowlevel_init
-lowlevel_init:
-
-	/* Set up GPIO pins first ----------------------------------------- */
-
-	ldr	r0, =GPSR0
-	ldr	r1, =CONFIG_SYS_GPSR0_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GPSR1
-	ldr	r1, =CONFIG_SYS_GPSR1_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GPSR2
-	ldr	r1, =CONFIG_SYS_GPSR2_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GPCR0
-	ldr	r1, =CONFIG_SYS_GPCR0_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GPCR1
-	ldr	r1, =CONFIG_SYS_GPCR1_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GPCR2
-	ldr	r1, =CONFIG_SYS_GPCR2_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GPDR0
-	ldr	r1, =CONFIG_SYS_GPDR0_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GPDR1
-	ldr	r1, =CONFIG_SYS_GPDR1_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GPDR2
-	ldr	r1, =CONFIG_SYS_GPDR2_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GAFR0_L
-	ldr	r1, =CONFIG_SYS_GAFR0_L_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GAFR0_U
-	ldr	r1, =CONFIG_SYS_GAFR0_U_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GAFR1_L
-	ldr	r1, =CONFIG_SYS_GAFR1_L_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GAFR1_U
-	ldr	r1, =CONFIG_SYS_GAFR1_U_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GAFR2_L
-	ldr	r1, =CONFIG_SYS_GAFR2_L_VAL
-	str	r1, [r0]
-
-	ldr	r0, =GAFR2_U
-	ldr	r1, =CONFIG_SYS_GAFR2_U_VAL
-	str	r1, [r0]
-
-	ldr	r0, =PSSR			/* enable GPIO pins */
-	ldr	r1, =CONFIG_SYS_PSSR_VAL
-	str	r1, [r0]
-
-	/* ---------------------------------------------------------------- */
-	/* Enable memory interface                                          */
-	/*                                                                  */
-	/* The sequence below is based on the recommended init steps        */
-	/* detailed in the Intel PXA250 Operating Systems Developers Guide, */
-	/* Chapter 10.                                                      */
-	/* ---------------------------------------------------------------- */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 1: Wait for at least 200 microsedonds to allow internal     */
-	/*         clocks to settle. Only necessary after hard reset...     */
-	/*         FIXME: can be optimized later                            */
-	/* ---------------------------------------------------------------- */
-
-	ldr	r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov	r2, #0
-	str	r2, [r3]
-	ldr	r4, =0x300			/* really 0x2E1 is about 200usec,   */
-						/* so 0x300 should be plenty        */
-1:
-	ldr	r2, [r3]
-	cmp	r4, r2
-	bgt	1b
-
-mem_init:
-
-	ldr	r1, =MEMC_BASE			/* get memory controller base addr. */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2a: Initialize Asynchronous static memory controller        */
-	/* ---------------------------------------------------------------- */
-
-	/* MSC registers: timing, bus width, mem type                       */
-
-	/* MSC0: nCS(0,1)                                                   */
-	ldr	r2, =CONFIG_SYS_MSC0_VAL
-	str	r2, [r1, #MSC0_OFFSET]
-	ldr	r2, [r1, #MSC0_OFFSET]		/* read back to ensure      */
-						/* that data latches        */
-	/* MSC1: nCS(2,3)                                                   */
-	ldr	r2, =CONFIG_SYS_MSC1_VAL
-	str	r2, [r1, #MSC1_OFFSET]
-	ldr	r2, [r1, #MSC1_OFFSET]
-
-	/* MSC2: nCS(4,5)                                                   */
-	ldr	r2, =CONFIG_SYS_MSC2_VAL
-	str	r2, [r1, #MSC2_OFFSET]
-	ldr	r2, [r1, #MSC2_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2b: Initialize Card Interface                               */
-	/* ---------------------------------------------------------------- */
-
-	/* MECR: Memory Expansion Card Register                             */
-	ldr	r2, =CONFIG_SYS_MECR_VAL
-	str	r2, [r1, #MECR_OFFSET]
-	ldr	r2, [r1, #MECR_OFFSET]
-
-	/* MCMEM0: Card Interface slot 0 timing                             */
-	ldr	r2, =CONFIG_SYS_MCMEM0_VAL
-	str	r2, [r1, #MCMEM0_OFFSET]
-	ldr	r2, [r1, #MCMEM0_OFFSET]
-
-	/* MCMEM1: Card Interface slot 1 timing                             */
-	ldr	r2, =CONFIG_SYS_MCMEM1_VAL
-	str	r2, [r1, #MCMEM1_OFFSET]
-	ldr	r2, [r1, #MCMEM1_OFFSET]
-
-	/* MCATT0: Card Interface Attribute Space Timing, slot 0            */
-	ldr	r2, =CONFIG_SYS_MCATT0_VAL
-	str	r2, [r1, #MCATT0_OFFSET]
-	ldr	r2, [r1, #MCATT0_OFFSET]
-
-	/* MCATT1: Card Interface Attribute Space Timing, slot 1            */
-	ldr	r2, =CONFIG_SYS_MCATT1_VAL
-	str	r2, [r1, #MCATT1_OFFSET]
-	ldr	r2, [r1, #MCATT1_OFFSET]
-
-	/* MCIO0: Card Interface I/O Space Timing, slot 0                   */
-	ldr	r2, =CONFIG_SYS_MCIO0_VAL
-	str	r2, [r1, #MCIO0_OFFSET]
-	ldr	r2, [r1, #MCIO0_OFFSET]
-
-	/* MCIO1: Card Interface I/O Space Timing, slot 1                   */
-	ldr	r2, =CONFIG_SYS_MCIO1_VAL
-	str	r2, [r1, #MCIO1_OFFSET]
-	ldr	r2, [r1, #MCIO1_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2c: Write FLYCNFG  FIXME: what's that???                    */
-	/* ---------------------------------------------------------------- */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2d: Initialize Timing for Sync Memory (SDCLK0)              */
-	/* ---------------------------------------------------------------- */
-
-	/* Before accessing MDREFR we need a valid DRI field, so we set     */
-	/* this to power on defaults + DRI field, set SDRAM clocks free running */
-
-	ldr	r3, =CONFIG_SYS_MDREFR_VAL
-	ldr	r2, =0xFFF
-	and	r3, r3,  r2
-
-	ldr	r0, [r1, #MDREFR_OFFSET]
-	bic	r0, r0, r2
-	bic	r0, r0, #(MDREFR_K0FREE|MDREFR_K1FREE|MDREFR_K2FREE)
-	orr	r0, r0, r3
-
-	str	r0, [r1, #MDREFR_OFFSET]	/* write back MDREFR        */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */
-	/* ---------------------------------------------------------------- */
-
-	/* Initialize SXCNFG register. Assert the enable bits               */
-
-	/* Write SXMRS to cause an MRS command to all enabled banks of      */
-	/* synchronous static memory. Note that SXLCR need not be written   */
-	/* at this time.                                                    */
-
-	/* FIXME: we use async mode for now                                 */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 4: Initialize SDRAM                                         */
-	/* ---------------------------------------------------------------- */
-
-	/* set MDREFR according to user define with exception of a few bits */
-
-	ldr     r4, =CONFIG_SYS_MDREFR_VAL
-	ldr	r2, =(MDREFR_K0RUN|MDREFR_K0DB2|MDREFR_K1RUN|MDREFR_K1DB2|\
-					MDREFR_K2RUN |MDREFR_K2DB2)
-	and	r4, r4, r2
-	bic	r0, r0, r2
-	orr	r0, r0, r4
-
-	str     r0, [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r0, [r1, #MDREFR_OFFSET]
-
-	/* Step 4b: de-assert MDREFR:SLFRSH.                                */
-
-	bic	r0, r0, #(MDREFR_SLFRSH)
-	str     r0, [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r0, [r1, #MDREFR_OFFSET]
-
-
-	/* Step 4c: assert MDREFR:E1PIN and E0PIO as desired, set KXFREE  */
-
-	ldr     r4, =CONFIG_SYS_MDREFR_VAL
-	ldr	r2, =(MDREFR_E0PIN|MDREFR_E1PIN|MDREFR_K0FREE| \
-			MDREFR_K1FREE | MDREFR_K2FREE)
-	and	r4, r4, r2
-	orr	r0, r0, r4
-	str     r0, [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r0, [r1, #MDREFR_OFFSET]
-
-
-	/* Step 4d: write MDCNFG with MDCNFG:DEx deasserted (set to 0), to  */
-	/*          configure but not enable each SDRAM partition pair.     */
-
-	ldr	r4, =CONFIG_SYS_MDCNFG_VAL
-	bic	r4, r4, #(MDCNFG_DE0|MDCNFG_DE1)
-	bic	r4, r4, #(MDCNFG_DE2|MDCNFG_DE3)
-	str     r4, [r1, #MDCNFG_OFFSET]	/* write back MDCNFG        */
-	ldr     r4, [r1, #MDCNFG_OFFSET]
-
-
-	/* Step 4e: Wait for the clock to the SDRAMs to stabilize,          */
-	/*          100..200 µsec.                                          */
-
-	ldr	r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov	r2, #0
-	str	r2, [r3]
-	ldr	r4, =0x300			/* really 0x2E1 is about 200usec,   */
-						/* so 0x300 should be plenty        */
-1:
-	ldr	r2, [r3]
-	cmp	r4, r2
-	bgt	1b
-
-
-	/* Step 4f: Trigger a number (usually 8) refresh cycles by          */
-	/*          attempting non-burst read or write accesses to disabled */
-	/*          SDRAM, as commonly specified in the power up sequence   */
-	/*          documented in SDRAM data sheets. The address(es) used   */
-	/*          for this purpose must not be cacheable.                 */
-
-	ldr	r3, =CONFIG_SYS_DRAM_BASE
-.rept 8
-	str	r2, [r3]
-.endr
-
-	/* Step 4g: Write MDCNFG with enable bits asserted                  */
-	/*          (MDCNFG:DEx set to 1).                                  */
-
-	ldr     r3, [r1, #MDCNFG_OFFSET]
-	orr	r3, r3, #(MDCNFG_DE0|MDCNFG_DE1)
-	str     r3, [r1, #MDCNFG_OFFSET]
-
-	/* Step 4h: Write MDMRS.                                            */
-
-	ldr     r2, =CONFIG_SYS_MDMRS_VAL
-	str     r2, [r1, #MDMRS_OFFSET]
-
-
-	/* We are finished with Intel's memory controller initialisation    */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Disable (mask) all interrupts at interrupt controller            */
-	/* ---------------------------------------------------------------- */
-
-initirqs:
-
-	mov     r1, #0		/* clear int. level register (IRQ, not FIQ) */
-	ldr     r2, =ICLR
-	str     r1, [r2]
-
-	ldr     r2, =ICMR	/* mask all interrupts at the controller    */
-	str     r1, [r2]
-
-
-	/* ---------------------------------------------------------------- */
-	/* Clock initialisation                                             */
-	/* ---------------------------------------------------------------- */
-
-initclks:
-
-	/* Disable the peripheral clocks, and set the core clock frequency  */
-
-	/* Turn Off ALL on-chip peripheral clocks for re-configuration      */
-	/* Note: See label 'ENABLECLKS' for the re-enabling                 */
-	ldr     r1, =CKEN
-	mov     r2, #0
-	str     r2, [r1]
-
-
-	/* default value in case no valid rotary switch setting is found    */
-	ldr     r2, =(CCCR_L27|CCCR_M2|CCCR_N10)  /* DEFAULT: {200/200/100} */
-
-	/* ... and write the core clock config register                     */
-	ldr     r1, =CCCR
-	str     r2, [r1]
-
-#ifdef RTC
-	/* enable the 32Khz oscillator for RTC and PowerManager             */
-
-	ldr     r1, =OSCC
-	mov     r2, #OSCC_OON
-	str     r2, [r1]
-
-	/* NOTE:  spin here until OSCC.OOK get set, meaning the PLL         */
-	/* has settled.                                                     */
-60:
-	ldr     r2, [r1]
-	ands    r2, r2, #1
-	beq     60b
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/*                                                                  */
-	/* ---------------------------------------------------------------- */
-
-	/* Save SDRAM size */
-	ldr     r1, =DRAM_SIZE
-	str	r8, [r1]
-
-	/* Interrupt init: Mask all interrupts                              */
-	ldr	r0, =ICMR /* enable no sources */
-	mov	r1, #0
-	str	r1, [r0]
-
-	/* FIXME */
-
-#define NODEBUG
-#ifdef NODEBUG
-	/*Disable software and data breakpoints */
-	mov	r0,#0
-	mcr	p15,0,r0,c14,c8,0  /* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0  /* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0  /* dbcon */
-
-	/*Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0  /* dcsr */
-
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* End lowlevel_init                                                     */
-	/* ---------------------------------------------------------------- */
-
-endlowlevel_init:
-
-	mov     pc, lr
diff --git a/board/colibri_pxa270/Makefile b/board/colibri_pxa270/Makefile
index ae570e1..f8b44ab 100644
--- a/board/colibri_pxa270/Makefile
+++ b/board/colibri_pxa270/Makefile
@@ -24,17 +24,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= colibri_pxa270.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/colibri_pxa270/colibri_pxa270.c b/board/colibri_pxa270/colibri_pxa270.c
index 8aa7067..191fb33 100644
--- a/board/colibri_pxa270/colibri_pxa270.c
+++ b/board/colibri_pxa270/colibri_pxa270.c
@@ -42,8 +42,9 @@ struct serial_device *default_serial_console (void)
 
 int board_init (void)
 {
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
 
 	/* arch number of vpac270 */
 	gd->bd->bi_arch_number = MACH_TYPE_COLIBRI;
@@ -54,13 +55,18 @@ int board_init (void)
 	return 0;
 }
 
-int dram_init (void)
+extern void pxa_dram_init(void);
+int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
 
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
 }
 
 #ifdef	CONFIG_CMD_USB
diff --git a/board/colibri_pxa270/config.mk b/board/colibri_pxa270/config.mk
deleted file mode 100644
index 0f10662..0000000
--- a/board/colibri_pxa270/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0xa1000000
diff --git a/board/colibri_pxa270/lowlevel_init.S b/board/colibri_pxa270/lowlevel_init.S
deleted file mode 100644
index a43dac2..0000000
--- a/board/colibri_pxa270/lowlevel_init.S
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * Toradex Colibri PXA270 Lowlevel Hardware Initialization
- *
- * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/macro.h>
-
-.globl lowlevel_init
-lowlevel_init:
-	pxa_gpio_setup
-	pxa_wait_ticks	0x8000
-	pxa_mem_setup
-	pxa_wakeup
-	pxa_intr_setup
-	pxa_clock_setup
-
-	mov	pc, lr
diff --git a/board/cradle/Makefile b/board/cradle/Makefile
index 1ae785d..720593c 100644
--- a/board/cradle/Makefile
+++ b/board/cradle/Makefile
@@ -26,17 +26,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= cradle.o flash.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/cradle/config.mk b/board/cradle/config.mk
deleted file mode 100644
index 6656bdd..0000000
--- a/board/cradle/config.mk
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0xa0f80000
-#CONFIG_SYS_TEXT_BASE = 0
diff --git a/board/cradle/cradle.c b/board/cradle/cradle.c
index c4a93f9..2bbf2d5 100644
--- a/board/cradle/cradle.c
+++ b/board/cradle/cradle.c
@@ -185,6 +185,10 @@ int
 board_init (void)
 /**********************************************************/
 {
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
+
 	led_code (0xf, YELLOW);
 
 	/* arch number of HHP Cradle */
@@ -206,24 +210,18 @@ board_init (void)
 	return 1;
 }
 
-int
-/**********************************************************/
-dram_init (void)
-/**********************************************************/
+extern void pxa_dram_init(void);
+int dram_init(void)
+{
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
+
+void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size  = PHYS_SDRAM_1_SIZE;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size  = PHYS_SDRAM_2_SIZE;
-	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size  = PHYS_SDRAM_3_SIZE;
-	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size  = PHYS_SDRAM_4_SIZE;
-
-	return (PHYS_SDRAM_1_SIZE +
-		PHYS_SDRAM_2_SIZE +
-		PHYS_SDRAM_3_SIZE +
-		PHYS_SDRAM_4_SIZE );
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
 }
 
 #ifdef CONFIG_CMD_NET
diff --git a/board/cradle/lowlevel_init.S b/board/cradle/lowlevel_init.S
deleted file mode 100644
index 39964b6..0000000
--- a/board/cradle/lowlevel_init.S
+++ /dev/null
@@ -1,515 +0,0 @@
-/*
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-/* wait for coprocessor write complete */
-   .macro CPWAIT reg
-   mrc  p15,0,\reg,c2,c0,0
-   mov  \reg,\reg
-   sub  pc,pc,#4
-   .endm
-
-   .macro SET_LED val
-   ldr   r6, =GPCR2
-   ldr   r7, =0
-   str   r7, [r6]
-   ldr   r6, =GPSR2
-   ldr   r7, =\val
-   str   r7, [r6]
-   .endm
-
-
-.globl lowlevel_init
-lowlevel_init:
-
-    mov      r10, lr
-
-    /* Set up GPIO pins first */
-
-   ldr      r0,   =GPSR0
-   ldr      r1,   =CONFIG_SYS_GPSR0_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GPSR1
-   ldr      r1,   =CONFIG_SYS_GPSR1_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GPSR2
-   ldr      r1,   =CONFIG_SYS_GPSR2_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GPCR0
-   ldr      r1,   =CONFIG_SYS_GPCR0_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GPCR1
-   ldr      r1,   =CONFIG_SYS_GPCR1_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GPCR2
-   ldr      r1,   =CONFIG_SYS_GPCR2_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GRER0
-   ldr      r1,   =CONFIG_SYS_GRER0_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GRER1
-   ldr      r1,   =CONFIG_SYS_GRER1_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GRER2
-   ldr      r1,   =CONFIG_SYS_GRER2_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GFER0
-   ldr      r1,   =CONFIG_SYS_GFER0_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GFER1
-   ldr      r1,   =CONFIG_SYS_GFER1_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GFER2
-   ldr      r1,   =CONFIG_SYS_GFER2_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GPDR0
-   ldr      r1,   =CONFIG_SYS_GPDR0_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GPDR1
-   ldr      r1,   =CONFIG_SYS_GPDR1_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GPDR2
-   ldr      r1,   =CONFIG_SYS_GPDR2_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GAFR0_L
-   ldr      r1,   =CONFIG_SYS_GAFR0_L_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GAFR0_U
-   ldr      r1,   =CONFIG_SYS_GAFR0_U_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GAFR1_L
-   ldr      r1,   =CONFIG_SYS_GAFR1_L_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GAFR1_U
-   ldr      r1,   =CONFIG_SYS_GAFR1_U_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GAFR2_L
-   ldr      r1,   =CONFIG_SYS_GAFR2_L_VAL
-   str      r1,   [r0]
-
-   ldr      r0,   =GAFR2_U
-   ldr      r1,   =CONFIG_SYS_GAFR2_U_VAL
-   str      r1,   [r0]
-
-   /* enable GPIO pins */
-   ldr      r0,   =PSSR
-   ldr      r1,   =CONFIG_SYS_PSSR_VAL
-   str      r1,   [r0]
-
-   SET_LED 1
-
-   ldr    r3, =MSC1             /* low - bank 2 Lubbock Registers / SRAM */
-   ldr    r2, =CONFIG_SYS_MSC1_VAL     /* high - bank 3 Ethernet Controller */
-   str    r2, [r3]              /* need to set MSC1 before trying to write to the HEX LEDs */
-   ldr    r2, [r3]              /* need to read it back to make sure the value latches (see MSC section of manual) */
-
-
-/*********************************************************************
-    Initlialize Memory Controller
-
-    See PXA250 Operating System Developer's Guide
-
-    pause for 200 uSecs- allow internal clocks to settle
-    *Note: only need this if hard reset... doing it anyway for now
-*/
-
-    @ Step 1
-   @ ---- Wait 200 usec
-   ldr r3, =OSCR       @ reset the OS Timer Count to zero
-   mov r2, #0
-   str r2, [r3]
-   ldr r4, =0x300         @ really 0x2E1 is about 200usec, so 0x300 should be plenty
-1:
-   ldr r2, [r3]
-   cmp r4, r2
-   bgt 1b
-
-   SET_LED 2
-
-mem_init:
-	@ get memory controller base address
-	ldr     r1,  =MEMC_BASE
-
-
-@****************************************************************************
-@  Step 2
-@
-
-   @ Step 2a
-   @ write msc0, read back to ensure data latches
-   @
-   ldr     r2,   =CONFIG_SYS_MSC0_VAL
-   str     r2,   [r1, #MSC0_OFFSET]
-   ldr     r2,   [r1, #MSC0_OFFSET]
-
-   @ write msc1
-   ldr     r2,  =CONFIG_SYS_MSC1_VAL
-   str     r2,  [r1, #MSC1_OFFSET]
-   ldr     r2,  [r1, #MSC1_OFFSET]
-
-   @ write msc2
-   ldr     r2,  =CONFIG_SYS_MSC2_VAL
-   str     r2,  [r1, #MSC2_OFFSET]
-   ldr     r2,  [r1, #MSC2_OFFSET]
-
-   @ Step 2b
-   @ write mecr
-   ldr     r2,  =CONFIG_SYS_MECR_VAL
-   str     r2,  [r1, #MECR_OFFSET]
-
-   @ write mcmem0
-   ldr     r2,  =CONFIG_SYS_MCMEM0_VAL
-   str     r2,  [r1, #MCMEM0_OFFSET]
-
-   @ write mcmem1
-   ldr     r2,  =CONFIG_SYS_MCMEM1_VAL
-   str     r2,  [r1, #MCMEM1_OFFSET]
-
-   @ write mcatt0
-   ldr     r2,  =CONFIG_SYS_MCATT0_VAL
-   str     r2,  [r1, #MCATT0_OFFSET]
-
-   @ write mcatt1
-   ldr     r2,  =CONFIG_SYS_MCATT1_VAL
-   str     r2,  [r1, #MCATT1_OFFSET]
-
-   @ write mcio0
-   ldr     r2,  =CONFIG_SYS_MCIO0_VAL
-   str     r2,  [r1, #MCIO0_OFFSET]
-
-   @ write mcio1
-   ldr     r2,  =CONFIG_SYS_MCIO1_VAL
-   str     r2,  [r1, #MCIO1_OFFSET]
-
-   /*SET_LED 3 */
-
-   @ Step 2c
-   @ fly-by-dma is defeatured on this part
-   @ write flycnfg
-   @ldr     r2,  =CONFIG_SYS_FLYCNFG_VAL
-   @str     r2,  [r1, #FLYCNFG_OFFSET]
-
-/* FIXME Does this sequence really make sense */
-#ifdef REDBOOT_WAY
-   @ Step 2d
-   @ get the mdrefr settings
-   ldr     r3,  =CONFIG_SYS_MDREFR_VAL
-
-   @ extract DRI field (we need a valid DRI field)
-   @
-   ldr     r2,  =0xFFF
-
-   @ valid DRI field in r3
-   @
-   and     r3,  r3,  r2
-
-   @ get the reset state of MDREFR
-   @
-   ldr     r4,  [r1, #MDREFR_OFFSET]
-
-   @ clear the DRI field
-   @
-   bic     r4,  r4,  r2
-
-   @ insert the valid DRI field loaded above
-   @
-   orr     r4,  r4,  r3
-
-   @ write back mdrefr
-   @
-   str     r4,  [r1, #MDREFR_OFFSET]
-
-   @ *Note: preserve the mdrefr value in r4 *
-
-   /*SET_LED 4 */
-
-@****************************************************************************
-@  Step 3
-@
-@ NO SRAM
-
-   mov   pc, r10
-
-
-@****************************************************************************
-@  Step 4
-@
-
-   @ Assumes previous mdrefr value in r4, if not then read current mdrefr
-
-   @ clear the free-running clock bits
-   @ (clear K0Free, K1Free, K2Free
-   @
-   bic     r4,  r4,  #(0x00800000 | 0x01000000 | 0x02000000)
-
-   @ set K0RUN for CPLD clock
-   @
-   orr   r4,  r4,  #0x00002000
-
-   @ set K1RUN if bank 0 installed
-   @
-   orr   r4,  r4,  #0x00010000
-
-   @ write back mdrefr
-   @
-   str     r4,  [r1, #MDREFR_OFFSET]
-   ldr     r4,  [r1, #MDREFR_OFFSET]
-
-   @ deassert SLFRSH
-   @
-   bic     r4,  r4,  #0x00400000
-
-   @ write back mdrefr
-   @
-   str     r4,  [r1, #MDREFR_OFFSET]
-
-   @ assert E1PIN
-   @
-   orr     r4,  r4,  #0x00008000
-
-   @ write back mdrefr
-   @
-   str     r4,  [r1, #MDREFR_OFFSET]
-   ldr     r4,  [r1, #MDREFR_OFFSET]
-   nop
-   nop
-#else
-   @ Step 2d
-   @ get the mdrefr settings
-   ldr     r3,  =CONFIG_SYS_MDREFR_VAL
-
-   @ write back mdrefr
-   @
-   str     r4,  [r1, #MDREFR_OFFSET]
-
-   @  Step 4
-
-   @ set K0RUN for CPLD clock
-   @
-   orr   r4,  r4,  #0x00002000
-
-   @ set K1RUN for bank 0
-   @
-   orr   r4,  r4,  #0x00010000
-
-   @ write back mdrefr
-   @
-   str     r4,  [r1, #MDREFR_OFFSET]
-   ldr     r4,  [r1, #MDREFR_OFFSET]
-
-   @ deassert SLFRSH
-   @
-   bic     r4,  r4,  #0x00400000
-
-   @ write back mdrefr
-   @
-   str     r4,  [r1, #MDREFR_OFFSET]
-
-   @ assert E1PIN
-   @
-   orr     r4,  r4,  #0x00008000
-
-   @ write back mdrefr
-   @
-   str     r4,  [r1, #MDREFR_OFFSET]
-   ldr     r4,  [r1, #MDREFR_OFFSET]
-   nop
-   nop
-#endif
-
-   @ Step 4d
-   @ fetch platform value of mdcnfg
-   @
-   ldr     r2,  =CONFIG_SYS_MDCNFG_VAL
-
-   @ disable all sdram banks
-   @
-   bic     r2,  r2,  #(MDCNFG_DE0 | MDCNFG_DE1)
-   bic     r2,  r2,  #(MDCNFG_DE2 | MDCNFG_DE3)
-
-   @ program banks 0/1 for bus width
-   @
-   bic   r2,  r2,  #MDCNFG_DWID0      @0=32-bit
-
-   @ write initial value of mdcnfg, w/o enabling sdram banks
-   @
-   str     r2,  [r1, #MDCNFG_OFFSET]
-
-   @ Step 4e
-   @ pause for 200 uSecs
-   @
-   ldr r3, =OSCR       @ reset the OS Timer Count to zero
-   mov r2, #0
-   str r2, [r3]
-   ldr r4, =0x300			@ really 0x2E1 is about 200usec, so 0x300 should be plenty
-1:
-   ldr r2, [r3]
-   cmp r4, r2
-   bgt 1b
-
-   /*SET_LED 5 */
-
-   /* Why is this here??? */
-   mov    r0, #0x78                @turn everything off
-   mcr    p15, 0, r0, c1, c0, 0      @(caches off, MMU off, etc.)
-
-   @ Step 4f
-   @ Access memory *not yet enabled* for CBR refresh cycles (8)
-   @ - CBR is generated for all banks
-
-   ldr     r2, =CONFIG_SYS_DRAM_BASE
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-
-   @ Step 4g
-   @get memory controller base address
-   @
-   ldr     r1,  =MEMC_BASE
-
-   @fetch current mdcnfg value
-   @
-   ldr     r3,  [r1, #MDCNFG_OFFSET]
-
-   @enable sdram bank 0 if installed (must do for any populated bank)
-   @
-   orr     r3,  r3,  #MDCNFG_DE0
-
-   @write back mdcnfg, enabling the sdram bank(s)
-   @
-   str     r3,  [r1, #MDCNFG_OFFSET]
-
-   @ Step 4h
-   @ write mdmrs
-   @
-   ldr     r2,  =CONFIG_SYS_MDMRS_VAL
-   str     r2,  [r1, #MDMRS_OFFSET]
-
-   @ Done Memory Init
-
-   /*SET_LED 6 */
-
-   @********************************************************************
-   @ Disable (mask) all interrupts at the interrupt controller
-   @
-
-   @ clear the interrupt level register (use IRQ, not FIQ)
-   @
-   mov     r1, #0
-   ldr     r2,  =ICLR
-   str     r1,  [r2]
-
-   @ Set interrupt mask register
-   @
-   ldr     r1,  =CONFIG_SYS_ICMR_VAL
-   ldr     r2,  =ICMR
-   str     r1,  [r2]
-
-   @ ********************************************************************
-   @ Disable the peripheral clocks, and set the core clock
-   @
-
-	@ Turn Off ALL on-chip peripheral clocks for re-configuration
-	@
-   ldr     r1,  =CKEN
-   mov     r2,  #0
-   str     r2,  [r1]
-
-   @ set core clocks
-   @
-   ldr     r2,  =CONFIG_SYS_CCCR_VAL
-   ldr     r1,  =CCCR
-   str     r2,  [r1]
-
-#ifdef ENABLE32KHZ
-   @ enable the 32Khz oscillator for RTC and PowerManager
-   @
-   ldr     r1,  =OSCC
-   mov     r2,  #OSCC_OON
-   str     r2,  [r1]
-
-   @ NOTE:  spin here until OSCC.OOK get set,
-   @        meaning the PLL has settled.
-   @
-60:
-   ldr     r2, [r1]
-   ands    r2, r2, #1
-   beq     60b
-#endif
-
-	@ Turn on needed clocks
-	@
-   ldr     r1,  =CKEN
-   ldr     r2,  =CONFIG_SYS_CKEN_VAL
-   str     r2,  [r1]
-
-   /*SET_LED 7 */
-
-/* Is this needed???? */
-#define NODEBUG
-#ifdef NODEBUG
-   /*Disable software and data breakpoints */
-   mov   r0,#0
-   mcr   p15,0,r0,c14,c8,0  /* ibcr0 */
-   mcr   p15,0,r0,c14,c9,0  /* ibcr1 */
-   mcr   p15,0,r0,c14,c4,0  /* dbcon */
-
-   /*Enable all debug functionality */
-   mov   r0,#0x80000000
-   mcr   p14,0,r0,c10,c0,0  /* dcsr */
-
-#endif
-
-   /*SET_LED 8 */
-
-   mov   pc, r10
-
-@ End lowlevel_init
diff --git a/board/csb226/Makefile b/board/csb226/Makefile
index c12dbea..5e1332b 100644
--- a/board/csb226/Makefile
+++ b/board/csb226/Makefile
@@ -26,17 +26,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= csb226.o flash.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/csb226/config.mk b/board/csb226/config.mk
deleted file mode 100644
index 9e46555..0000000
--- a/board/csb226/config.mk
+++ /dev/null
@@ -1,15 +0,0 @@
-#
-# Linux-Kernel is expected to be at c000'8000, entry c000'8000
-#
-# we load ourself to c170'0000, the upper 1 MB of second bank
-#
-# download areas is c800'0000
-#
-
-# This is the address where U-Boot lives in flash:
-#CONFIG_SYS_TEXT_BASE = 0
-
-# FIXME: armboot does only work correctly when being compiled
-# for the addresses _after_ relocation to RAM!! Otherwhise the
-# .bss segment is assumed in flash...
-CONFIG_SYS_TEXT_BASE = 0xa1fe0000
diff --git a/board/csb226/csb226.c b/board/csb226/csb226.c
index 6eed9ad..dd29e62 100644
--- a/board/csb226/csb226.c
+++ b/board/csb226/csb226.c
@@ -69,8 +69,9 @@ int misc_init_r(void)
 
 int board_init (void)
 {
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
 
 	/* arch number of CSB226 board */
 	gd->bd->bi_arch_number = MACH_TYPE_CSB226;
@@ -82,21 +83,20 @@ int board_init (void)
 }
 
 
-/**
- * dram_init: - setup dynamic RAM
- *
- * @return: 0 in case of success
- */
+extern void pxa_dram_init(void);
+int dram_init(void)
+{
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
 
-int dram_init (void)
+void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
 }
 
-
 /**
  * csb226_set_led: - switch LEDs on or off
  *
diff --git a/board/csb226/lowlevel_init.S b/board/csb226/lowlevel_init.S
deleted file mode 100644
index 55169be..0000000
--- a/board/csb226/lowlevel_init.S
+++ /dev/null
@@ -1,437 +0,0 @@
-/*
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * NOTE: I haven't clean this up considerably, just enough to get it
- * running. See hal_platform_setup.h for the source. See
- * board/cradle/lowlevel_init.S for another PXA250 setup that is
- * much cleaner.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-/* wait for coprocessor write complete */
-   .macro CPWAIT reg
-   mrc  p15,0,\reg,c2,c0,0
-   mov  \reg,\reg
-   sub  pc,pc,#4
-   .endm
-
-_TEXT_BASE:
-	.word	CONFIG_SYS_TEXT_BASE
-
-
-/*
- *	Memory setup
- */
-
-.globl lowlevel_init
-lowlevel_init:
-
-    mov      r10, lr
-
-	/* Set up GPIO pins first ----------------------------------------- */
-
-	ldr		r0,	=GPSR0
-	ldr		r1,	=CONFIG_SYS_GPSR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR1
-	ldr		r1,	=CONFIG_SYS_GPSR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR2
-	ldr		r1,	=CONFIG_SYS_GPSR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR0
-	ldr		r1,	=CONFIG_SYS_GPCR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR1
-	ldr		r1,	=CONFIG_SYS_GPCR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR2
-	ldr		r1,	=CONFIG_SYS_GPCR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR0
-	ldr		r1,	=CONFIG_SYS_GPDR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR1
-	ldr		r1,	=CONFIG_SYS_GPDR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR2
-	ldr		r1,	=CONFIG_SYS_GPDR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_L
-	ldr		r1,	=CONFIG_SYS_GAFR0_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_U
-	ldr		r1,	=CONFIG_SYS_GAFR0_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_L
-	ldr		r1,	=CONFIG_SYS_GAFR1_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_U
-	ldr		r1,	=CONFIG_SYS_GAFR1_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_L
-	ldr		r1,	=CONFIG_SYS_GAFR2_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_U
-	ldr		r1,	=CONFIG_SYS_GAFR2_U_VAL
-	str		r1,   [r0]
-
-	ldr	r0,	=PSSR		/* enable GPIO pins */
-	ldr		r1,	=CONFIG_SYS_PSSR_VAL
-	str		r1,   [r0]
-
-/*	ldr	r3,	=MSC1		/  low - bank 2 Lubbock Registers / SRAM */
-/*	ldr	r2,	=CONFIG_SYS_MSC1_VAL	/  high - bank 3 Ethernet Controller */
-/*	str	r2,	[r3]		/  need to set MSC1 before trying to write to the HEX LEDs */
-/*	ldr	r2,	[r3]		/  need to read it back to make sure the value latches (see MSC section of manual) */
-/* */
-/*	ldr	r1,	=LED_BLANK */
-/*	mov	r0,	#0xFF */
-/*	str	r0,	[r1]		/  turn on hex leds */
-/* */
-/*loop: */
-/* */
-/*   ldr	r0, =0xB0070001 */
-/*   ldr	r1, =_LED */
-/*   str	r0, [r1]		/  hex display */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Enable memory interface                                          */
-	/*                                                                  */
-	/* The sequence below is based on the recommended init steps        */
-	/* detailed in the Intel PXA250 Operating Systems Developers Guide, */
-	/* Chapter 10.                                                      */
-	/* ---------------------------------------------------------------- */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 1: Wait for at least 200 microsedonds to allow internal     */
-	/*         clocks to settle. Only necessary after hard reset...     */
-	/*         FIXME: can be optimized later                            */
-	/* ---------------------------------------------------------------- */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	ldr r2, [r3]
-	cmp r4, r2
-	bgt 1b
-
-mem_init:
-
-	ldr     r1,  =MEMC_BASE		/* get memory controller base addr. */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2a: Initialize Asynchronous static memory controller        */
-	/* ---------------------------------------------------------------- */
-
-	/* MSC registers: timing, bus width, mem type                       */
-
-	/* MSC0: nCS(0,1)                                                   */
-	ldr     r2,   =CONFIG_SYS_MSC0_VAL
-	str     r2,   [r1, #MSC0_OFFSET]
-	ldr     r2,   [r1, #MSC0_OFFSET]	/* read back to ensure      */
-						/* that data latches        */
-	/* MSC1: nCS(2,3)                                                   */
-	ldr     r2,  =CONFIG_SYS_MSC1_VAL
-	str     r2,  [r1, #MSC1_OFFSET]
-	ldr     r2,  [r1, #MSC1_OFFSET]
-
-	/* MSC2: nCS(4,5)                                                   */
-	ldr     r2,  =CONFIG_SYS_MSC2_VAL
-	str     r2,  [r1, #MSC2_OFFSET]
-	ldr     r2,  [r1, #MSC2_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2b: Initialize Card Interface                               */
-	/* ---------------------------------------------------------------- */
-
-	/* MECR: Memory Expansion Card Register                             */
-	ldr     r2,  =CONFIG_SYS_MECR_VAL
-	str     r2,  [r1, #MECR_OFFSET]
-	ldr	r2,	[r1, #MECR_OFFSET]
-
-	/* MCMEM0: Card Interface slot 0 timing                             */
-	ldr     r2,  =CONFIG_SYS_MCMEM0_VAL
-	str     r2,  [r1, #MCMEM0_OFFSET]
-	ldr	r2,	[r1, #MCMEM0_OFFSET]
-
-	/* MCMEM1: Card Interface slot 1 timing                             */
-	ldr     r2,  =CONFIG_SYS_MCMEM1_VAL
-	str     r2,  [r1, #MCMEM1_OFFSET]
-	ldr	r2,	[r1, #MCMEM1_OFFSET]
-
-	/* MCATT0: Card Interface Attribute Space Timing, slot 0            */
-	ldr     r2,  =CONFIG_SYS_MCATT0_VAL
-	str     r2,  [r1, #MCATT0_OFFSET]
-	ldr	r2,	[r1, #MCATT0_OFFSET]
-
-	/* MCATT1: Card Interface Attribute Space Timing, slot 1            */
-	ldr     r2,  =CONFIG_SYS_MCATT1_VAL
-	str     r2,  [r1, #MCATT1_OFFSET]
-	ldr	r2,	[r1, #MCATT1_OFFSET]
-
-	/* MCIO0: Card Interface I/O Space Timing, slot 0                   */
-	ldr     r2,  =CONFIG_SYS_MCIO0_VAL
-	str     r2,  [r1, #MCIO0_OFFSET]
-	ldr	r2,	[r1, #MCIO0_OFFSET]
-
-	/* MCIO1: Card Interface I/O Space Timing, slot 1                   */
-	ldr     r2,  =CONFIG_SYS_MCIO1_VAL
-	str     r2,  [r1, #MCIO1_OFFSET]
-	ldr	r2,	[r1, #MCIO1_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2c: Write FLYCNFG  FIXME: what's that???                    */
-	/* ---------------------------------------------------------------- */
-
-	/* test if we run from flash or RAM - RAM/BDI: don't setup RAM      */
-	adr	r3, mem_init		/* r0 <- current position of code   */
-	ldr	r2, =mem_init
-	cmp	r3, r2			/* skip init if in place            */
-	beq	initirqs
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2d: Initialize Timing for Sync Memory (SDCLK0)              */
-	/* ---------------------------------------------------------------- */
-
-	/* Before accessing MDREFR we need a valid DRI field, so we set     */
-	/* this to power on defaults + DRI field.                           */
-
-	ldr	r3,	=CONFIG_SYS_MDREFR_VAL
-	ldr	r2,	=0xFFF
-	and	r3,	r3, r2
-	ldr	r4,	=0x03ca4000
-	orr	r4,	r4,  r3
-
-	str	r4,	[r1, #MDREFR_OFFSET]	/* write back MDREFR        */
-	ldr     r4,	[r1, #MDREFR_OFFSET]
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */
-	/* ---------------------------------------------------------------- */
-
-	/* Initialize SXCNFG register. Assert the enable bits               */
-
-	/* Write SXMRS to cause an MRS command to all enabled banks of      */
-	/* synchronous static memory. Note that SXLCR need not be written   */
-	/* at this time.                                                    */
-
-	/* FIXME: we use async mode for now                                 */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 4: Initialize SDRAM                                         */
-	/* ---------------------------------------------------------------- */
-
-	/* Step 4a: assert MDREFR:K?RUN and configure                       */
-	/*          MDREFR:K1DB2 and MDREFR:K2DB2 as desired.               */
-
-	ldr	r4,	=CONFIG_SYS_MDREFR_VAL
-	str	r4,	[r1, #MDREFR_OFFSET]	/* write back MDREFR        */
-	ldr	r4,	[r1, #MDREFR_OFFSET]
-
-	/* Step 4b: de-assert MDREFR:SLFRSH.                                */
-
-	bic	r4,	r4, #(MDREFR_SLFRSH)
-
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,     [r1, #MDREFR_OFFSET]
-
-
-	/* Step 4c: assert MDREFR:E1PIN and E0PIO                           */
-
-	orr	r4,	r4,	#(MDREFR_E1PIN|MDREFR_E0PIN)
-
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,     [r1, #MDREFR_OFFSET]
-
-
-	/* Step 4d: write MDCNFG with MDCNFG:DEx deasserted (set to 0), to  */
-	/*          configure but not enable each SDRAM partition pair.     */
-
-	ldr	r4,	=CONFIG_SYS_MDCNFG_VAL
-	bic	r4,	r4,	#(MDCNFG_DE0|MDCNFG_DE1)
-
-	str     r4,     [r1, #MDCNFG_OFFSET]	/* write back MDCNFG        */
-	ldr     r4,     [r1, #MDCNFG_OFFSET]
-
-
-	/* Step 4e: Wait for the clock to the SDRAMs to stabilize,          */
-	/*          100..200 µsec.                                          */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	ldr r2, [r3]
-	cmp r4, r2
-	bgt 1b
-
-
-	/* Step 4f: Trigger a number (usually 8) refresh cycles by          */
-	/*          attempting non-burst read or write accesses to disabled */
-	/*          SDRAM, as commonly specified in the power up sequence   */
-	/*          documented in SDRAM data sheets. The address(es) used   */
-	/*          for this purpose must not be cacheable.                 */
-
-	/*          There should 9 writes, since the first write doesn't    */
-	/*          trigger a refresh cycle on PXA250. See Intel PXA250 and */
-	/*          PXA210 Processors Specification Update,                 */
-	/*          Jan 2003, Errata #116, page 30.                         */
-
-
-	ldr	r3,	=CONFIG_SYS_DRAM_BASE
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-
-	/* Step 4g: Write MDCNFG with enable bits asserted                  */
-	/*          (MDCNFG:DEx set to 1).                                  */
-
-	ldr	r3, [r1, #MDCNFG_OFFSET]
-	orr	r3,	r3,	#(MDCNFG_DE0|MDCNFG_DE1)
-	str	r3, [r1, #MDCNFG_OFFSET]
-
-	/* Step 4h: Write MDMRS.                                            */
-
-	ldr     r2,  =CONFIG_SYS_MDMRS_VAL
-	str     r2,  [r1, #MDMRS_OFFSET]
-
-
-	/* We are finished with Intel's memory controller initialisation    */
-
-	/* ---------------------------------------------------------------- */
-	/* Disable (mask) all interrupts at interrupt controller            */
-	/* ---------------------------------------------------------------- */
-
-initirqs:
-
-	mov     r1, #0		/* clear int. level register (IRQ, not FIQ) */
-	ldr     r2,  =ICLR
-	str     r1,  [r2]
-
-	ldr     r2,  =ICMR	/* mask all interrupts at the controller    */
-	str     r1,  [r2]
-
-
-	/* ---------------------------------------------------------------- */
-	/* Clock initialisation                                             */
-	/* ---------------------------------------------------------------- */
-
-initclks:
-
-	/* Disable the peripheral clocks, and set the core clock frequency  */
-	/* (hard-coding at 398.12MHz for now).                              */
-
-	/* Turn Off ALL on-chip peripheral clocks for re-configuration      */
-	/* Note: See label 'ENABLECLKS' for the re-enabling                 */
-	ldr     r1,  =CKEN
-	mov     r2,  #0
-	str     r2,  [r1]
-
-
-	/* default value in case no valid rotary switch setting is found    */
-	ldr     r2, =(CCCR_L27|CCCR_M2|CCCR_N10)  /* DEFAULT: {200/200/100} */
-
-	/* ... and write the core clock config register                     */
-	ldr     r1,  =CCCR
-	str     r2,  [r1]
-
-	/* enable the 32Khz oscillator for RTC and PowerManager             */
-/*
-	ldr     r1,  =OSCC
-	mov     r2,  #OSCC_OON
-	str     r2,  [r1]
-*/
-	/* NOTE:  spin here until OSCC.OOK get set, meaning the PLL         */
-	/* has settled.                                                     */
-60:
-	ldr     r2, [r1]
-	ands    r2, r2, #1
-	beq     60b
-
-	/* ---------------------------------------------------------------- */
-	/*                                                                  */
-	/* ---------------------------------------------------------------- */
-
-	/* Save SDRAM size                                                  */
-	ldr	r1, =DRAM_SIZE
-	str	r8, [r1]
-
-	/* Interrupt init: Mask all interrupts                              */
-	ldr	r0, =ICMR			/* enable no sources        */
-	mov	r1, #0
-	str	r1, [r0]
-
-	/* FIXME */
-
-#ifndef DEBUG
-	/*Disable software and data breakpoints */
-	mov	r0,#0
-	mcr	p15,0,r0,c14,c8,0  /* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0  /* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0  /* dbcon */
-
-	/*Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0  /* dcsr */
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* End lowlevel_init                                                     */
-	/* ---------------------------------------------------------------- */
-
-endlowlevel_init:
-
-    mov     pc, lr
diff --git a/board/delta/Makefile b/board/delta/Makefile
deleted file mode 100644
index 648e00c..0000000
--- a/board/delta/Makefile
+++ /dev/null
@@ -1,52 +0,0 @@
-
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).a
-
-COBJS	:= delta.o nand.o
-SOBJS	:= lowlevel_init.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-
-clean:
-	rm -f $(SOBJS) $(OBJS)
-
-distclean:	clean
-	rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/delta/config.mk b/board/delta/config.mk
deleted file mode 100644
index 8b24044..0000000
--- a/board/delta/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0x83008000
diff --git a/board/delta/delta.c b/board/delta/delta.c
deleted file mode 100644
index df23076..0000000
--- a/board/delta/delta.c
+++ /dev/null
@@ -1,378 +0,0 @@
-/*
- * (C) Copyright 2006
- * DENX Software Engineering
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <i2c.h>
-#include <da9030.h>
-#include <malloc.h>
-#include <command.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/io.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* ------------------------------------------------------------------------- */
-
-static void init_DA9030(void);
-static void keys_init(void);
-static void get_pressed_keys(uchar *s);
-static uchar *key_match(uchar *kbd_data);
-
-/*
- * Miscelaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
-
-	/* arch number of Lubbock-Board mk@tbd: fix this! */
-	gd->bd->bi_arch_number = MACH_TYPE_LUBBOCK;
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0xa0000100;
-
-	return 0;
-}
-
-int board_late_init(void)
-{
-#ifdef DELTA_CHECK_KEYBD
-	uchar kbd_data[KEYBD_DATALEN];
-	char keybd_env[2 * KEYBD_DATALEN + 1];
-	char *str;
-	int i;
-#endif /* DELTA_CHECK_KEYBD */
-
-	setenv("stdout", "serial");
-	setenv("stderr", "serial");
-
-#ifdef DELTA_CHECK_KEYBD
-	keys_init();
-
-	memset(kbd_data, '\0', KEYBD_DATALEN);
-
-	/* check for pressed keys and setup keybd_env */
-	get_pressed_keys(kbd_data);
-
-	for (i = 0; i < KEYBD_DATALEN; ++i) {
-		sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
-	}
-	setenv ("keybd", keybd_env);
-
-	str = strdup ((char *)key_match (kbd_data));	/* decode keys */
-
-# ifdef CONFIG_PREBOOT	/* automatically configure "preboot" command on key match */
-	setenv ("preboot", str);	/* set or delete definition */
-# endif /* CONFIG_PREBOOT */
-	if (str != NULL) {
-		free (str);
-	}
-#endif /* DELTA_CHECK_KEYBD */
-
-	init_DA9030();
-	return 0;
-}
-
-/*
- * Magic Key Handling, mainly copied from board/lwmon/lwmon.c
- */
-#ifdef DELTA_CHECK_KEYBD
-
-static uchar kbd_magic_prefix[] = "key_magic";
-static uchar kbd_command_prefix[] = "key_cmd";
-
-/*
- * Get pressed keys
- * s is a buffer of size KEYBD_DATALEN-1
- */
-static void get_pressed_keys(uchar *s)
-{
-	unsigned long val;
-	val = readl(GPLR3);
-
-	if(val & (1<<31))
-		*s++ = KEYBD_KP_DKIN0;
-	if(val & (1<<18))
-		*s++ = KEYBD_KP_DKIN1;
-	if(val & (1<<29))
-		*s++ = KEYBD_KP_DKIN2;
-	if(val & (1<<22))
-		*s++ = KEYBD_KP_DKIN5;
-}
-
-static void keys_init()
-{
-	writel(readl(CKENB) | CKENB_7_GPIO, CKENB);
-	udelay(100);
-
-	/* Configure GPIOs */
-	writel(0xa840, GPIO127);	/* KP_DKIN0 */
-	writel(0xa840, GPIO114);	/* KP_DKIN1 */
-	writel(0xa840, GPIO125);	/* KP_DKIN2 */
-	writel(0xa840, GPIO118);	/* KP_DKIN5 */
-
-	/* Configure GPIOs as inputs */
-	writel(readl(GPDR3) & ~(1<<31 | 1<<18 | 1<<29 | 1<<22), GPDR3);
-	writel((1<<31 | 1<<18 | 1<<29 | 1<<22), GCDR3);
-
-	udelay(100);
-}
-
-static int compare_magic (uchar *kbd_data, uchar *str)
-{
-	/* uchar compare[KEYBD_DATALEN-1]; */
-	uchar compare[KEYBD_DATALEN];
-	char *nxt;
-	int i;
-
-	/* Don't include modifier byte */
-	/* memcpy (compare, kbd_data+1, KEYBD_DATALEN-1); */
-	memcpy (compare, kbd_data, KEYBD_DATALEN);
-
-	for (; str != NULL; str = (*nxt) ? (uchar *)(nxt+1) : (uchar *)nxt) {
-		uchar c;
-		int k;
-
-		c = (uchar) simple_strtoul ((char *)str, (char **) (&nxt), 16);
-
-		if (str == (uchar *)nxt) {	/* invalid character */
-			break;
-		}
-
-		/*
-		 * Check if this key matches the input.
-		 * Set matches to zero, so they match only once
-		 * and we can find duplicates or extra keys
-		 */
-		for (k = 0; k < sizeof(compare); ++k) {
-			if (compare[k] == '\0')	/* only non-zero entries */
-				continue;
-			if (c == compare[k]) {	/* found matching key */
-				compare[k] = '\0';
-				break;
-			}
-		}
-		if (k == sizeof(compare)) {
-			return -1;		/* unmatched key */
-		}
-	}
-
-	/*
-	 * A full match leaves no keys in the `compare' array,
-	 */
-	for (i = 0; i < sizeof(compare); ++i) {
-		if (compare[i])
-		{
-			return -1;
-		}
-	}
-
-	return 0;
-}
-
-
-static uchar *key_match (uchar *kbd_data)
-{
-	char magic[sizeof (kbd_magic_prefix) + 1];
-	uchar *suffix;
-	char *kbd_magic_keys;
-
-	/*
-	 * The following string defines the characters that can pe appended
-	 * to "key_magic" to form the names of environment variables that
-	 * hold "magic" key codes, i. e. such key codes that can cause
-	 * pre-boot actions. If the string is empty (""), then only
-	 * "key_magic" is checked (old behaviour); the string "125" causes
-	 * checks for "key_magic1", "key_magic2" and "key_magic5", etc.
-	 */
-	if ((kbd_magic_keys = getenv ("magic_keys")) == NULL)
-		kbd_magic_keys = "";
-
-	/* loop over all magic keys;
-	 * use '\0' suffix in case of empty string
-	 */
-	for (suffix=(uchar *)kbd_magic_keys; *suffix || suffix==(uchar *)kbd_magic_keys; ++suffix) {
-		sprintf (magic, "%s%c", kbd_magic_prefix, *suffix);
-#if 0
-		printf ("### Check magic \"%s\"\n", magic);
-#endif
-		if (compare_magic(kbd_data, (uchar *)getenv(magic)) == 0) {
-			char cmd_name[sizeof (kbd_command_prefix) + 1];
-			char *cmd;
-
-			sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix);
-
-			cmd = getenv (cmd_name);
-#if 0
-			printf ("### Set PREBOOT to $(%s): \"%s\"\n",
-				cmd_name, cmd ? cmd : "<<NULL>>");
-#endif
-			*kbd_data = *suffix;
-			return ((uchar *)cmd);
-		}
-	}
-#if 0
-	printf ("### Delete PREBOOT\n");
-#endif
-	*kbd_data = '\0';
-	return (NULL);
-}
-
-int do_kbd (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	uchar kbd_data[KEYBD_DATALEN];
-	char keybd_env[2 * KEYBD_DATALEN + 1];
-	int i;
-
-	/* Read keys */
-	get_pressed_keys(kbd_data);
-	puts ("Keys:");
-	for (i = 0; i < KEYBD_DATALEN; ++i) {
-		sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
-		printf (" %02x", kbd_data[i]);
-	}
-	putc ('\n');
-	setenv ("keybd", keybd_env);
-	return 0;
-}
-
-U_BOOT_CMD(
-	   kbd,	1,	1,	do_kbd,
-	   "read keyboard status",
-	   ""
-);
-
-#endif /* DELTA_CHECK_KEYBD */
-
-
-int dram_init (void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
-	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
-	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
-
-	return 0;
-}
-
-void i2c_init_board()
-{
-	writel(readl(CKENB) | (CKENB_4_I2C), CKENB);
-
-	/* setup I2C GPIO's */
-	writel(0x801, GPIO32);		/* SCL = Alt. Fkt. 1 */
-	writel(0x801, GPIO33);		/* SDA = Alt. Fkt. 1 */
-}
-
-/* initialize the DA9030 Power Controller */
-static void init_DA9030()
-{
-	uchar addr = (uchar) DA9030_I2C_ADDR, val = 0;
-
-	writel(readl(CKENB) | CKENB_7_GPIO, CKENB);
-	udelay(100);
-
-	/* Rising Edge on EXTON to reset DA9030 */
-	writel(0x8800, GPIO17);	/* configure GPIO17, no pullup, -down */
-	writel(readl(GPDR0) | (1<<17), GPDR0);	/* GPIO17 is output */
-	writel((1<<17), GSDR0);
-	writel((1<<17), GPCR0);	/* drive GPIO17 low */
-	writel((1<<17), GPSR0);	/* drive GPIO17 high */
-
-#if CONFIG_SYS_DA9030_EXTON_DELAY
-	udelay((unsigned long) CONFIG_SYS_DA9030_EXTON_DELAY);	/* wait for DA9030 */
-#endif
-	writel((1<<17), GPCR0);	/* drive GPIO17 low */
-
-	/* reset the watchdog and go active (0xec) */
-	val = (SYS_CONTROL_A_HWRES_ENABLE |
-	       (0x6<<4) |
-	       SYS_CONTROL_A_WDOG_ACTION |
-	       SYS_CONTROL_A_WATCHDOG);
-	if(i2c_write(addr, SYS_CONTROL_A, 1, &val, 1)) {
-		printf("Error accessing DA9030 via i2c.\n");
-		return;
-	}
-
-	val = 0x80;
-	if(i2c_write(addr, IRQ_MASK_B, 1, &val, 1)) {
-		printf("Error accessing DA9030 via i2c.\n");
-		return;
-	}
-
-	i2c_reg_write(addr, REG_CONTROL_1_97, 0xfd); /* disable LDO1, enable LDO6 */
-	i2c_reg_write(addr, LDO2_3, 0xd1);	/* LDO2 =1,9V, LDO3=3,1V */
-	i2c_reg_write(addr, LDO4_5, 0xcc);	/* LDO2 =1,9V, LDO3=3,1V */
-	i2c_reg_write(addr, LDO6_SIMCP, 0x3e);	/* LDO6=3,2V, SIMCP = 5V support */
-	i2c_reg_write(addr, LDO7_8, 0xc9);	/* LDO7=2,7V, LDO8=3,0V */
-	i2c_reg_write(addr, LDO9_12, 0xec);	/* LDO9=3,0V, LDO12=3,2V */
-	i2c_reg_write(addr, BUCK, 0x0c);	/* Buck=1.2V */
-	i2c_reg_write(addr, REG_CONTROL_2_98, 0x7f); /* All LDO'S on 8,9,10,11,12,14 */
-	i2c_reg_write(addr, LDO_10_11, 0xcc);	/* LDO10=3.0V  LDO11=3.0V */
-	i2c_reg_write(addr, LDO_15, 0xae);	/* LDO15=1.8V, dislock first 3bit */
-	i2c_reg_write(addr, LDO_14_16, 0x05);	/* LDO14=2.8V, LDO16=NB */
-	i2c_reg_write(addr, LDO_18_19, 0x9c);	/* LDO18=3.0V, LDO19=2.7V */
-	i2c_reg_write(addr, LDO_17_SIMCP0, 0x2c); /* LDO17=3.0V, SIMCP=3V support */
-	i2c_reg_write(addr, BUCK2_DVC1, 0x9a);	/* Buck2=1.5V plus Update support of 520 MHz */
-	i2c_reg_write(addr, REG_CONTROL_2_18, 0x43); /* Ball on */
-	i2c_reg_write(addr, MISC_CONTROLB, 0x08); /* session valid enable */
-	i2c_reg_write(addr, USBPUMP, 0xc1);	/* start pump, ignore HW signals */
-
-	val = i2c_reg_read(addr, STATUS);
-	if(val & STATUS_CHDET)
-		printf("Charger detected, turning on LED.\n");
-	else {
-		printf("No charger detetected.\n");
-		/* undervoltage? print error and power down */
-	}
-}
-
-
-#if 0
-/* reset the DA9030 watchdog */
-void hw_watchdog_reset(void)
-{
-	uchar addr = (uchar) DA9030_I2C_ADDR, val = 0;
-	val = i2c_reg_read(addr, SYS_CONTROL_A);
-	val |= SYS_CONTROL_A_WATCHDOG;
-	i2c_reg_write(addr, SYS_CONTROL_A, val);
-}
-#endif
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_SMC91111
-	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
-	return rc;
-}
-#endif
diff --git a/board/delta/lowlevel_init.S b/board/delta/lowlevel_init.S
deleted file mode 100644
index 1664f3b..0000000
--- a/board/delta/lowlevel_init.S
+++ /dev/null
@@ -1,146 +0,0 @@
-/*
- * (C) Copyright 2006 DENX Software Engineering
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-.macro wait time
-	ldr		r2, =OSCR
-	mov		r3, #0
-	str		r3, [r2]
-0:
-	ldr		r3, [r2]
-	cmp		r3, \time
-	bls		0b
-.endm
-
-.globl lowlevel_init
-lowlevel_init:
-	/* Set up GPIO pins first */
-	mov	 r10, lr
-
-	/*  Configure GPIO  Pins 97, 98 UART1 / altern. Fkt. 1 */
-	ldr		r0, =GPIO97
-	ldr		r1, =0x801
-	str		r1, [r0]
-
-	ldr		r0, =GPIO98
-	ldr		r1, =0x801
-	str		r1, [r0]
-
-	/* tebrandt - ASCR, clear the RDH bit */
-	ldr		r0, =ASCR
-	ldr		r1, [r0]
-	bic		r1, r1, #0x80000000
-	str		r1, [r0]
-
-mem_init:
-	/* Configure ACCR Register - enable DMEMC Clock at 260 / 2 MHz */
-	ldr		r0, =ACCR
-	ldr		r1, [r0]
-	orr		r1, r1, #0x3000
-	str		r1, [r0]
-	ldr		r1, [r0]
-
-	/* 2. Programm MDCNFG, leaving DMCEN de-asserted */
-	ldr		r0, =MDCNFG
-	ldr		r1, =(MDCNFG_DMAP | MDCNFG_DTYPE | MDCNFG_DTC_2 | MDCNFG_DCSE0 | MDCNFG_DRAC_13)
-	/* ldr		r1, =0x80000403 */
-	str		r1, [r0]
-	ldr		r1, [r0]	/* delay until written */
-
-	/* 3. wait nop power up waiting period (200ms)
-	 * optimization: Steps 4+6 can be done during this
-	 */
-	wait #0x300
-
-	/* 4. Perform an initial Rcomp-calibration cycle */
-	ldr		r0, =RCOMP
-	ldr		r1, =0x80000000
-	str		r1, [r0]
-	ldr		r1, [r0]	/* delay until written */
-	/* missing: program for automatic rcomp evaluation cycles */
-
-	/* 5. DDR DRAM strobe delay calibration */
-	ldr		r0, =DDR_HCAL
-	ldr		r1, =0x88000007
-	str		r1, [r0]
-	wait		#5
-	ldr		r1, [r0]	/* delay until written */
-
-	/* Set MDMRS */
-	ldr		r0, =MDMRS
-	ldr		r1, =0x60000033
-	str		r1, [r0]
-	wait	#300
-
-	/* Configure MDREFR */
-	ldr		r0, =MDREFR
-	ldr		r1, =0x00000006
-	str		r1, [r0]
-	ldr		r1, [r0]
-
-	/* Enable the dynamic memory controller */
-	ldr		r0, =MDCNFG
-	ldr		r1, [r0]
-	orr		r1, r1, #MDCNFG_DMCEN
-	str		r1, [r0]
-
-#ifndef CONFIG_SYS_SKIP_DRAM_SCRUB
-	/* scrub/init SDRAM if enabled/present */
-	ldr	r8, =CONFIG_SYS_DRAM_BASE	/* base address of SDRAM (CONFIG_SYS_DRAM_BASE) */
-	ldr	r9, =CONFIG_SYS_DRAM_SIZE	/* size of memory to scrub (CONFIG_SYS_DRAM_SIZE) */
-	mov	r0, #0			/* scrub with 0x0000:0000 */
-	mov	r1, #0
-	mov	r2, #0
-	mov	r3, #0
-	mov	r4, #0
-	mov	r5, #0
-	mov	r6, #0
-	mov	r7, #0
-10:	/* fastScrubLoop */
-	subs	r9, r9, #32	/* 8 words/line */
-	stmia	r8!, {r0-r7}
-	beq	15f
-	b	10b
-#endif /* CONFIG_SYS_SKIP_DRAM_SCRUB */
-
-15:
-	/* Mask all interrupts */
-	mov	r1, #0
-	mcr	p6, 0, r1, c1, c0, 0	@ ICMR
-
-	/* Disable software and data breakpoints */
-	mov	r0, #0
-	mcr	p15,0,r0,c14,c8,0  /* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0  /* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0  /* dbcon */
-
-	/* Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0  /* dcsr */
-
-endlowlevel_init:
-	mov	pc, lr
diff --git a/board/delta/nand.c b/board/delta/nand.c
deleted file mode 100644
index 119a587..0000000
--- a/board/delta/nand.c
+++ /dev/null
@@ -1,558 +0,0 @@
-/*
- * (C) Copyright 2006 DENX Software Engineering
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <nand.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/io.h>
-
-#ifdef CONFIG_SYS_DFC_DEBUG1
-# define DFC_DEBUG1(fmt, args...) printf(fmt, ##args)
-#else
-# define DFC_DEBUG1(fmt, args...)
-#endif
-
-#ifdef CONFIG_SYS_DFC_DEBUG2
-# define DFC_DEBUG2(fmt, args...) printf(fmt, ##args)
-#else
-# define DFC_DEBUG2(fmt, args...)
-#endif
-
-#ifdef CONFIG_SYS_DFC_DEBUG3
-# define DFC_DEBUG3(fmt, args...) printf(fmt, ##args)
-#else
-# define DFC_DEBUG3(fmt, args...)
-#endif
-
-/* These really don't belong here, as they are specific to the NAND Model */
-static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
-
-static struct nand_bbt_descr delta_bbt_descr = {
-	.options = 0,
-	.offs = 0,
-	.len = 2,
-	.pattern = scan_ff_pattern
-};
-
-static struct nand_ecclayout delta_oob = {
-	.eccbytes = 6,
-	.eccpos = {2, 3, 4, 5, 6, 7},
-	.oobfree = { {8, 2}, {12, 4} }
-};
-
-/*
- * not required for Monahans DFC
- */
-static void dfc_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
-	return;
-}
-
-#if 0
-/* read device ready pin */
-static int dfc_device_ready(struct mtd_info *mtdinfo)
-{
-	if(NDSR & NDSR_RDY)
-		return 1;
-	else
-		return 0;
-	return 0;
-}
-#endif
-
-/*
- * Write buf to the DFC Controller Data Buffer
- */
-static void dfc_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
-{
-	unsigned long bytes_multi = len & 0xfffffffc;
-	unsigned long rest = len & 0x3;
-	unsigned long *long_buf;
-	int i;
-
-	DFC_DEBUG2("dfc_write_buf: writing %d bytes starting with 0x%x.\n", len, *((unsigned long*) buf));
-	if(bytes_multi) {
-		for(i=0; i<bytes_multi; i+=4) {
-			long_buf = (unsigned long*) &buf[i];
-			writel(*long_buf, NDDB);
-		}
-	}
-	if(rest) {
-		printf("dfc_write_buf: ERROR, writing non 4-byte aligned data.\n");
-	}
-	return;
-}
-
-
-static void dfc_read_buf(struct mtd_info *mtd, u_char* const buf, int len)
-{
-	int i=0, j;
-
-	/* we have to be carefull not to overflow the buffer if len is
-	 * not a multiple of 4 */
-	unsigned long bytes_multi = len & 0xfffffffc;
-	unsigned long rest = len & 0x3;
-	unsigned long *long_buf;
-
-	DFC_DEBUG3("dfc_read_buf: reading %d bytes.\n", len);
-	/* if there are any, first copy multiple of 4 bytes */
-	if(bytes_multi) {
-		for(i=0; i<bytes_multi; i+=4) {
-			long_buf = (unsigned long*) &buf[i];
-			*long_buf = readl(NDDB);
-		}
-	}
-
-	/* ...then the rest */
-	if(rest) {
-		unsigned long rest_data = NDDB;
-		for(j=0;j<rest; j++)
-			buf[i+j] = (u_char) ((rest_data>>j) & 0xff);
-	}
-
-	return;
-}
-
-/*
- * read a word. Not implemented as not used in NAND code.
- */
-static u16 dfc_read_word(struct mtd_info *mtd)
-{
-	printf("dfc_read_word: UNIMPLEMENTED.\n");
-	return 0;
-}
-
-/* global var, too bad: mk@tbd: move to ->priv pointer */
-static unsigned long read_buf = 0;
-static int bytes_read = -1;
-
-/*
- * read a byte from NDDB Because we can only read 4 bytes from NDDB at
- * a time, we buffer the remaining bytes. The buffer is reset when a
- * new command is sent to the chip.
- *
- * WARNING:
- * This function is currently only used to read status and id
- * bytes. For these commands always 8 bytes need to be read from
- * NDDB. So we read and discard these bytes right now. In case this
- * function is used for anything else in the future, we must check
- * what was the last command issued and read the appropriate amount of
- * bytes respectively.
- */
-static u_char dfc_read_byte(struct mtd_info *mtd)
-{
-	unsigned char byte;
-	unsigned long dummy;
-
-	if(bytes_read < 0) {
-		read_buf = readl(NDDB);
-		dummy = readl(NDDB);
-		bytes_read = 0;
-	}
-	byte = (unsigned char) (read_buf>>(8 * bytes_read++));
-	if(bytes_read >= 4)
-		bytes_read = -1;
-
-	DFC_DEBUG2("dfc_read_byte: byte %u: 0x%x of (0x%x).\n", bytes_read - 1, byte, read_buf);
-	return byte;
-}
-
-/* calculate delta between OSCR values start and now  */
-static unsigned long get_delta(unsigned long start)
-{
-	unsigned long cur = readl(OSCR);
-
-	if(cur < start) /* OSCR overflowed */
-		return (cur + (start^0xffffffff));
-	else
-		return (cur - start);
-}
-
-/* delay function, this doesn't belong here */
-static void wait_us(unsigned long us)
-{
-	unsigned long start = readl(OSCR);
-	us = DIV_ROUND_UP(us * OSCR_CLK_FREQ, 1000);
-
-	while (get_delta(start) < us) {
-		/* do nothing */
-	}
-}
-
-static void dfc_clear_nddb(void)
-{
-	writel(readl(NDCR) & ~NDCR_ND_RUN, NDCR);
-	wait_us(CONFIG_SYS_NAND_OTHER_TO);
-}
-
-/* wait_event with timeout */
-static unsigned long dfc_wait_event(unsigned long event)
-{
-	unsigned long ndsr, timeout, start = readl(OSCR);
-
-	if(!event)
-		return 0xff000000;
-	else if(event & (NDSR_CS0_CMDD | NDSR_CS0_BBD))
-		timeout = DIV_ROUND_UP(CONFIG_SYS_NAND_PROG_ERASE_TO
-					* OSCR_CLK_FREQ, 1000);
-	else
-		timeout = DIV_ROUND_UP(CONFIG_SYS_NAND_OTHER_TO
-					* OSCR_CLK_FREQ, 1000);
-
-	while(1) {
-		ndsr = readl(NDSR);
-		if(ndsr & event) {
-			writel(readl(NDSR) | event, NDSR);
-			break;
-		}
-		if(get_delta(start) > timeout) {
-			DFC_DEBUG1("dfc_wait_event: TIMEOUT waiting for event: 0x%lx.\n", event);
-			return 0xff000000;
-		}
-
-	}
-	return ndsr;
-}
-
-/* we don't always wan't to do this */
-static void dfc_new_cmd(void)
-{
-	int retry = 0;
-	unsigned long status;
-
-	while(retry++ <= CONFIG_SYS_NAND_SENDCMD_RETRY) {
-		/* Clear NDSR */
-		writel(0xfff, NDSR);
-
-		/* set NDCR[NDRUN] */
-		if (!(readl(NDCR) & NDCR_ND_RUN))
-			writel(readl(NDCR) | NDCR_ND_RUN, NDCR);
-
-		status = dfc_wait_event(NDSR_WRCMDREQ);
-
-		if(status & NDSR_WRCMDREQ)
-			return;
-
-		DFC_DEBUG2("dfc_new_cmd: FAILED to get WRITECMDREQ, retry: %d.\n", retry);
-		dfc_clear_nddb();
-	}
-	DFC_DEBUG1("dfc_new_cmd: giving up after %d retries.\n", retry);
-}
-
-/* this function is called after Programm and Erase Operations to
- * check for success or failure */
-static int dfc_wait(struct mtd_info *mtd, struct nand_chip *this)
-{
-	unsigned long ndsr=0, event=0;
-	int state = this->state;
-
-	if(state == FL_WRITING) {
-		event = NDSR_CS0_CMDD | NDSR_CS0_BBD;
-	} else if(state == FL_ERASING) {
-		event = NDSR_CS0_CMDD | NDSR_CS0_BBD;
-	}
-
-	ndsr = dfc_wait_event(event);
-
-	if((ndsr & NDSR_CS0_BBD) || (ndsr & 0xff000000))
-		return(0x1); /* Status Read error */
-	return 0;
-}
-
-/* cmdfunc send commands to the DFC */
-static void dfc_cmdfunc(struct mtd_info *mtd, unsigned command,
-			int column, int page_addr)
-{
-	/* register struct nand_chip *this = mtd->priv; */
-	unsigned long ndcb0=0, ndcb1=0, ndcb2=0, event=0;
-
-	/* clear the ugly byte read buffer */
-	bytes_read = -1;
-	read_buf = 0;
-
-	switch (command) {
-	case NAND_CMD_READ0:
-		DFC_DEBUG3("dfc_cmdfunc: NAND_CMD_READ0, page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
-		dfc_new_cmd();
-		ndcb0 = (NAND_CMD_READ0 | (4<<16));
-		column >>= 1; /* adjust for 16 bit bus */
-		ndcb1 = (((column>>1) & 0xff) |
-			 ((page_addr<<8) & 0xff00) |
-			 ((page_addr<<8) & 0xff0000) |
-			 ((page_addr<<8) & 0xff000000)); /* make this 0x01000000 ? */
-		event = NDSR_RDDREQ;
-		goto write_cmd;
-	case NAND_CMD_READ1:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_READ1 unimplemented!\n");
-		goto end;
-	case NAND_CMD_READOOB:
-		DFC_DEBUG1("dfc_cmdfunc: NAND_CMD_READOOB unimplemented!\n");
-		goto end;
-	case NAND_CMD_READID:
-		dfc_new_cmd();
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_READID.\n");
-		ndcb0 = (NAND_CMD_READID | (3 << 21) | (1 << 16)); /* addr cycles*/
-		event = NDSR_RDDREQ;
-		goto write_cmd;
-	case NAND_CMD_PAGEPROG:
-		/* sent as a multicommand in NAND_CMD_SEQIN */
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_PAGEPROG empty due to multicmd.\n");
-		goto end;
-	case NAND_CMD_ERASE1:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_ERASE1,  page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
-		dfc_new_cmd();
-		ndcb0 = (0xd060 | (1<<25) | (2<<21) | (1<<19) | (3<<16));
-		ndcb1 = (page_addr & 0x00ffffff);
-		goto write_cmd;
-	case NAND_CMD_ERASE2:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_ERASE2 empty due to multicmd.\n");
-		goto end;
-	case NAND_CMD_SEQIN:
-		/* send PAGE_PROG command(0x1080) */
-		dfc_new_cmd();
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_SEQIN/PAGE_PROG,  page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
-		ndcb0 = (0x1080 | (1<<25) | (1<<21) | (1<<19) | (4<<16));
-		column >>= 1; /* adjust for 16 bit bus */
-		ndcb1 = (((column>>1) & 0xff) |
-			 ((page_addr<<8) & 0xff00) |
-			 ((page_addr<<8) & 0xff0000) |
-			 ((page_addr<<8) & 0xff000000)); /* make this 0x01000000 ? */
-		event = NDSR_WRDREQ;
-		goto write_cmd;
-	case NAND_CMD_STATUS:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_STATUS.\n");
-		dfc_new_cmd();
-		ndcb0 = NAND_CMD_STATUS | (4<<21);
-		event = NDSR_RDDREQ;
-		goto write_cmd;
-	case NAND_CMD_RESET:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_RESET.\n");
-		ndcb0 = NAND_CMD_RESET | (5<<21);
-		event = NDSR_CS0_CMDD;
-		goto write_cmd;
-	default:
-		printk("dfc_cmdfunc: error, unsupported command.\n");
-		goto end;
-	}
-
- write_cmd:
-	writel(ndcb0, NDCB0);
-	writel(ndcb1, NDCB0);
-	writel(ndcb2, NDCB0);
-
-	/*  wait_event: */
-	dfc_wait_event(event);
- end:
-	return;
-}
-
-static void dfc_gpio_init(void)
-{
-	DFC_DEBUG2("Setting up DFC GPIO's.\n");
-
-	/* no idea what is done here, see zylonite.c */
-	writel(0x1, GPIO4);
-
-	writel(0x00000001, DF_ALE_nWE1);
-	writel(0x00000001, DF_ALE_nWE2);
-	writel(0x00000001, DF_nCS0);
-	writel(0x00000001, DF_nCS1);
-	writel(0x00000001, DF_nWE);
-	writel(0x00000001, DF_nRE);
-	writel(0x00000001, DF_IO0);
-	writel(0x00000001, DF_IO8);
-	writel(0x00000001, DF_IO1);
-	writel(0x00000001, DF_IO9);
-	writel(0x00000001, DF_IO2);
-	writel(0x00000001, DF_IO10);
-	writel(0x00000001, DF_IO3);
-	writel(0x00000001, DF_IO11);
-	writel(0x00000001, DF_IO4);
-	writel(0x00000001, DF_IO12);
-	writel(0x00000001, DF_IO5);
-	writel(0x00000001, DF_IO13);
-	writel(0x00000001, DF_IO6);
-	writel(0x00000001, DF_IO14);
-	writel(0x00000001, DF_IO7);
-	writel(0x00000001, DF_IO15);
-
-	writel(0x1901, DF_nWE);
-	writel(0x1901, DF_nRE);
-	writel(0x1900, DF_CLE_nOE);
-	writel(0x1901, DF_ALE_nWE1);
-	writel(0x1900, DF_INT_RnB);
-}
-
-/*
- * Board-specific NAND initialization. The following members of the
- * argument are board-specific (per include/linux/mtd/nand_new.h):
- * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device
- * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device
- * - hwcontrol: hardwarespecific function for accesing control-lines
- * - dev_ready: hardwarespecific function for  accesing device ready/busy line
- * - enable_hwecc?: function to enable (reset)  hardware ecc generator. Must
- *   only be provided if a hardware ECC is available
- * - ecc.mode: mode of ecc, see defines
- * - chip_delay: chip dependent delay for transfering data from array to
- *   read regs (tR)
- * - options: various chip options. They can partly be set to inform
- *   nand_scan about special functionality. See the defines for further
- *   explanation
- * Members with a "?" were not set in the merged testing-NAND branch,
- * so they are not set here either.
- */
-int board_nand_init(struct nand_chip *nand)
-{
-	unsigned long tCH, tCS, tWH, tWP, tRH, tRP, tRP_high, tR, tWHR, tAR;
-
-	/* set up GPIO Control Registers */
-	dfc_gpio_init();
-
-	/* turn on the NAND Controller Clock (104 MHz @ D0) */
-	writel(readl(CKENA) | (CKENA_4_NAND | CKENA_9_SMC), CKENA);
-
-#undef CONFIG_SYS_TIMING_TIGHT
-#ifndef CONFIG_SYS_TIMING_TIGHT
-	tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tCH);
-	tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tCS);
-	tWH = MIN(((unsigned long) (NAND_TIMING_tWH * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tWH);
-	tWP = MIN(((unsigned long) (NAND_TIMING_tWP * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tWP);
-	tRH = MIN(((unsigned long) (NAND_TIMING_tRH * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tRH);
-	tRP = MIN(((unsigned long) (NAND_TIMING_tRP * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tRP);
-	tR = MIN(((unsigned long) (NAND_TIMING_tR * DFC_CLK_PER_US) + 1),
-		 DFC_MAX_tR);
-	tWHR = MIN(((unsigned long) (NAND_TIMING_tWHR * DFC_CLK_PER_US) + 1),
-		   DFC_MAX_tWHR);
-	tAR = MIN(((unsigned long) (NAND_TIMING_tAR * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tAR);
-#else /* this is the tight timing */
-
-	tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US)),
-		  DFC_MAX_tCH);
-	tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US)),
-		  DFC_MAX_tCS);
-	tWH = MIN(((unsigned long) (NAND_TIMING_tWH * DFC_CLK_PER_US)),
-		  DFC_MAX_tWH);
-	tWP = MIN(((unsigned long) (NAND_TIMING_tWP * DFC_CLK_PER_US)),
-		  DFC_MAX_tWP);
-	tRH = MIN(((unsigned long) (NAND_TIMING_tRH * DFC_CLK_PER_US)),
-		  DFC_MAX_tRH);
-	tRP = MIN(((unsigned long) (NAND_TIMING_tRP * DFC_CLK_PER_US)),
-		  DFC_MAX_tRP);
-	tR = MIN(((unsigned long) (NAND_TIMING_tR * DFC_CLK_PER_US) - tCH - 2),
-		 DFC_MAX_tR);
-	tWHR = MIN(((unsigned long) (NAND_TIMING_tWHR * DFC_CLK_PER_US) - tCH - 2),
-		   DFC_MAX_tWHR);
-	tAR = MIN(((unsigned long) (NAND_TIMING_tAR * DFC_CLK_PER_US) - 2),
-		  DFC_MAX_tAR);
-#endif /* CONFIG_SYS_TIMING_TIGHT */
-
-
-	DFC_DEBUG2("tCH=%u, tCS=%u, tWH=%u, tWP=%u, tRH=%u, tRP=%u, tR=%u, tWHR=%u, tAR=%u.\n", tCH, tCS, tWH, tWP, tRH, tRP, tR, tWHR, tAR);
-
-	/* tRP value is split in the register */
-	if(tRP & (1 << 4)) {
-		tRP_high = 1;
-		tRP &= ~(1 << 4);
-	} else {
-		tRP_high = 0;
-	}
-
-	writel((tCH << 19) |
-		(tCS << 16) |
-		(tWH << 11) |
-		(tWP << 8) |
-		(tRP_high << 6) |
-		(tRH << 3) |
-		(tRP << 0),
-		NDTR0CS0);
-
-	writel((tR << 16) |
-		(tWHR << 4) |
-		(tAR << 0),
-		NDTR1CS0);
-
-	/* If it doesn't work (unlikely) think about:
-	 *  - ecc enable
-	 *  - chip select don't care
-	 *  - read id byte count
-	 *
-	 * Intentionally enabled by not setting bits:
-	 *  - dma (DMA_EN)
-	 *  - page size = 512
-	 *  - cs don't care, see if we can enable later!
-	 *  - row address start position (after second cycle)
-	 *  - pages per block = 32
-	 *  - ND_RDY : clears command buffer
-	 */
-	/* NDCR_NCSX |		/\* Chip select busy don't care *\/ */
-
-	writel(NDCR_SPARE_EN |		/* use the spare area */
-		NDCR_DWIDTH_C |		/* 16bit DFC data bus width  */
-		NDCR_DWIDTH_M |		/* 16 bit Flash device data bus width */
-		(2 << 16) |		/* read id count = 7 ???? mk@tbd */
-		NDCR_ND_ARB_EN |	/* enable bus arbiter */
-		NDCR_RDYM |		/* flash device ready ir masked */
-		NDCR_CS0_PAGEDM |	/* ND_nCSx page done ir masked */
-		NDCR_CS1_PAGEDM |
-		NDCR_CS0_CMDDM |	/* ND_CSx command done ir masked */
-		NDCR_CS1_CMDDM |
-		NDCR_CS0_BBDM |		/* ND_CSx bad block detect ir masked */
-		NDCR_CS1_BBDM |
-		NDCR_DBERRM |		/* double bit error ir masked */
-		NDCR_SBERRM |		/* single bit error ir masked */
-		NDCR_WRDREQM |		/* write data request ir masked */
-		NDCR_RDDREQM |		/* read data request ir masked */
-		NDCR_WRCMDREQM,		/* write command request ir masked */
-		NDCR);
-
-
-	/* wait 10 us due to cmd buffer clear reset */
-	/*	wait(10); */
-
-
-	nand->cmd_ctrl = dfc_hwcontrol;
-/*	nand->dev_ready = dfc_device_ready; */
-	nand->ecc.mode = NAND_ECC_SOFT;
-	nand->ecc.layout = &delta_oob;
-	nand->options = NAND_BUSWIDTH_16;
-	nand->waitfunc = dfc_wait;
-	nand->read_byte = dfc_read_byte;
-	nand->read_word = dfc_read_word;
-	nand->read_buf = dfc_read_buf;
-	nand->write_buf = dfc_write_buf;
-
-	nand->cmdfunc = dfc_cmdfunc;
-	nand->badblock_pattern = &delta_bbt_descr;
-	return 0;
-}
-
-#endif
diff --git a/board/innokom/Makefile b/board/innokom/Makefile
index afae217..ba248c0 100644
--- a/board/innokom/Makefile
+++ b/board/innokom/Makefile
@@ -26,17 +26,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= innokom.o flash.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/innokom/config.mk b/board/innokom/config.mk
deleted file mode 100644
index 9e46555..0000000
--- a/board/innokom/config.mk
+++ /dev/null
@@ -1,15 +0,0 @@
-#
-# Linux-Kernel is expected to be at c000'8000, entry c000'8000
-#
-# we load ourself to c170'0000, the upper 1 MB of second bank
-#
-# download areas is c800'0000
-#
-
-# This is the address where U-Boot lives in flash:
-#CONFIG_SYS_TEXT_BASE = 0
-
-# FIXME: armboot does only work correctly when being compiled
-# for the addresses _after_ relocation to RAM!! Otherwhise the
-# .bss segment is assumed in flash...
-CONFIG_SYS_TEXT_BASE = 0xa1fe0000
diff --git a/board/innokom/innokom.c b/board/innokom/innokom.c
index 2c51125..e658c35 100644
--- a/board/innokom/innokom.c
+++ b/board/innokom/innokom.c
@@ -100,8 +100,9 @@ int misc_init_r(void)
 
 int board_init (void)
 {
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
 
 	gd->bd->bi_arch_number = MACH_TYPE_INNOKOM;
 	gd->bd->bi_boot_params = 0xa0000100;
@@ -110,22 +111,20 @@ int board_init (void)
 	return 0;
 }
 
+extern void pxa_dram_init(void);
+int dram_init(void)
+{
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
 
-/**
- * dram_init: - setup dynamic RAM
- *
- * @return: 0 in case of success
- */
-
-int dram_init (void)
+void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
 }
 
-
 /**
  * innokom_set_led: - switch LEDs on or off
  *
diff --git a/board/innokom/lowlevel_init.S b/board/innokom/lowlevel_init.S
deleted file mode 100644
index 55169be..0000000
--- a/board/innokom/lowlevel_init.S
+++ /dev/null
@@ -1,437 +0,0 @@
-/*
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * NOTE: I haven't clean this up considerably, just enough to get it
- * running. See hal_platform_setup.h for the source. See
- * board/cradle/lowlevel_init.S for another PXA250 setup that is
- * much cleaner.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-/* wait for coprocessor write complete */
-   .macro CPWAIT reg
-   mrc  p15,0,\reg,c2,c0,0
-   mov  \reg,\reg
-   sub  pc,pc,#4
-   .endm
-
-_TEXT_BASE:
-	.word	CONFIG_SYS_TEXT_BASE
-
-
-/*
- *	Memory setup
- */
-
-.globl lowlevel_init
-lowlevel_init:
-
-    mov      r10, lr
-
-	/* Set up GPIO pins first ----------------------------------------- */
-
-	ldr		r0,	=GPSR0
-	ldr		r1,	=CONFIG_SYS_GPSR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR1
-	ldr		r1,	=CONFIG_SYS_GPSR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR2
-	ldr		r1,	=CONFIG_SYS_GPSR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR0
-	ldr		r1,	=CONFIG_SYS_GPCR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR1
-	ldr		r1,	=CONFIG_SYS_GPCR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR2
-	ldr		r1,	=CONFIG_SYS_GPCR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR0
-	ldr		r1,	=CONFIG_SYS_GPDR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR1
-	ldr		r1,	=CONFIG_SYS_GPDR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR2
-	ldr		r1,	=CONFIG_SYS_GPDR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_L
-	ldr		r1,	=CONFIG_SYS_GAFR0_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_U
-	ldr		r1,	=CONFIG_SYS_GAFR0_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_L
-	ldr		r1,	=CONFIG_SYS_GAFR1_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_U
-	ldr		r1,	=CONFIG_SYS_GAFR1_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_L
-	ldr		r1,	=CONFIG_SYS_GAFR2_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_U
-	ldr		r1,	=CONFIG_SYS_GAFR2_U_VAL
-	str		r1,   [r0]
-
-	ldr	r0,	=PSSR		/* enable GPIO pins */
-	ldr		r1,	=CONFIG_SYS_PSSR_VAL
-	str		r1,   [r0]
-
-/*	ldr	r3,	=MSC1		/  low - bank 2 Lubbock Registers / SRAM */
-/*	ldr	r2,	=CONFIG_SYS_MSC1_VAL	/  high - bank 3 Ethernet Controller */
-/*	str	r2,	[r3]		/  need to set MSC1 before trying to write to the HEX LEDs */
-/*	ldr	r2,	[r3]		/  need to read it back to make sure the value latches (see MSC section of manual) */
-/* */
-/*	ldr	r1,	=LED_BLANK */
-/*	mov	r0,	#0xFF */
-/*	str	r0,	[r1]		/  turn on hex leds */
-/* */
-/*loop: */
-/* */
-/*   ldr	r0, =0xB0070001 */
-/*   ldr	r1, =_LED */
-/*   str	r0, [r1]		/  hex display */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Enable memory interface                                          */
-	/*                                                                  */
-	/* The sequence below is based on the recommended init steps        */
-	/* detailed in the Intel PXA250 Operating Systems Developers Guide, */
-	/* Chapter 10.                                                      */
-	/* ---------------------------------------------------------------- */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 1: Wait for at least 200 microsedonds to allow internal     */
-	/*         clocks to settle. Only necessary after hard reset...     */
-	/*         FIXME: can be optimized later                            */
-	/* ---------------------------------------------------------------- */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	ldr r2, [r3]
-	cmp r4, r2
-	bgt 1b
-
-mem_init:
-
-	ldr     r1,  =MEMC_BASE		/* get memory controller base addr. */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2a: Initialize Asynchronous static memory controller        */
-	/* ---------------------------------------------------------------- */
-
-	/* MSC registers: timing, bus width, mem type                       */
-
-	/* MSC0: nCS(0,1)                                                   */
-	ldr     r2,   =CONFIG_SYS_MSC0_VAL
-	str     r2,   [r1, #MSC0_OFFSET]
-	ldr     r2,   [r1, #MSC0_OFFSET]	/* read back to ensure      */
-						/* that data latches        */
-	/* MSC1: nCS(2,3)                                                   */
-	ldr     r2,  =CONFIG_SYS_MSC1_VAL
-	str     r2,  [r1, #MSC1_OFFSET]
-	ldr     r2,  [r1, #MSC1_OFFSET]
-
-	/* MSC2: nCS(4,5)                                                   */
-	ldr     r2,  =CONFIG_SYS_MSC2_VAL
-	str     r2,  [r1, #MSC2_OFFSET]
-	ldr     r2,  [r1, #MSC2_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2b: Initialize Card Interface                               */
-	/* ---------------------------------------------------------------- */
-
-	/* MECR: Memory Expansion Card Register                             */
-	ldr     r2,  =CONFIG_SYS_MECR_VAL
-	str     r2,  [r1, #MECR_OFFSET]
-	ldr	r2,	[r1, #MECR_OFFSET]
-
-	/* MCMEM0: Card Interface slot 0 timing                             */
-	ldr     r2,  =CONFIG_SYS_MCMEM0_VAL
-	str     r2,  [r1, #MCMEM0_OFFSET]
-	ldr	r2,	[r1, #MCMEM0_OFFSET]
-
-	/* MCMEM1: Card Interface slot 1 timing                             */
-	ldr     r2,  =CONFIG_SYS_MCMEM1_VAL
-	str     r2,  [r1, #MCMEM1_OFFSET]
-	ldr	r2,	[r1, #MCMEM1_OFFSET]
-
-	/* MCATT0: Card Interface Attribute Space Timing, slot 0            */
-	ldr     r2,  =CONFIG_SYS_MCATT0_VAL
-	str     r2,  [r1, #MCATT0_OFFSET]
-	ldr	r2,	[r1, #MCATT0_OFFSET]
-
-	/* MCATT1: Card Interface Attribute Space Timing, slot 1            */
-	ldr     r2,  =CONFIG_SYS_MCATT1_VAL
-	str     r2,  [r1, #MCATT1_OFFSET]
-	ldr	r2,	[r1, #MCATT1_OFFSET]
-
-	/* MCIO0: Card Interface I/O Space Timing, slot 0                   */
-	ldr     r2,  =CONFIG_SYS_MCIO0_VAL
-	str     r2,  [r1, #MCIO0_OFFSET]
-	ldr	r2,	[r1, #MCIO0_OFFSET]
-
-	/* MCIO1: Card Interface I/O Space Timing, slot 1                   */
-	ldr     r2,  =CONFIG_SYS_MCIO1_VAL
-	str     r2,  [r1, #MCIO1_OFFSET]
-	ldr	r2,	[r1, #MCIO1_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2c: Write FLYCNFG  FIXME: what's that???                    */
-	/* ---------------------------------------------------------------- */
-
-	/* test if we run from flash or RAM - RAM/BDI: don't setup RAM      */
-	adr	r3, mem_init		/* r0 <- current position of code   */
-	ldr	r2, =mem_init
-	cmp	r3, r2			/* skip init if in place            */
-	beq	initirqs
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2d: Initialize Timing for Sync Memory (SDCLK0)              */
-	/* ---------------------------------------------------------------- */
-
-	/* Before accessing MDREFR we need a valid DRI field, so we set     */
-	/* this to power on defaults + DRI field.                           */
-
-	ldr	r3,	=CONFIG_SYS_MDREFR_VAL
-	ldr	r2,	=0xFFF
-	and	r3,	r3, r2
-	ldr	r4,	=0x03ca4000
-	orr	r4,	r4,  r3
-
-	str	r4,	[r1, #MDREFR_OFFSET]	/* write back MDREFR        */
-	ldr     r4,	[r1, #MDREFR_OFFSET]
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */
-	/* ---------------------------------------------------------------- */
-
-	/* Initialize SXCNFG register. Assert the enable bits               */
-
-	/* Write SXMRS to cause an MRS command to all enabled banks of      */
-	/* synchronous static memory. Note that SXLCR need not be written   */
-	/* at this time.                                                    */
-
-	/* FIXME: we use async mode for now                                 */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 4: Initialize SDRAM                                         */
-	/* ---------------------------------------------------------------- */
-
-	/* Step 4a: assert MDREFR:K?RUN and configure                       */
-	/*          MDREFR:K1DB2 and MDREFR:K2DB2 as desired.               */
-
-	ldr	r4,	=CONFIG_SYS_MDREFR_VAL
-	str	r4,	[r1, #MDREFR_OFFSET]	/* write back MDREFR        */
-	ldr	r4,	[r1, #MDREFR_OFFSET]
-
-	/* Step 4b: de-assert MDREFR:SLFRSH.                                */
-
-	bic	r4,	r4, #(MDREFR_SLFRSH)
-
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,     [r1, #MDREFR_OFFSET]
-
-
-	/* Step 4c: assert MDREFR:E1PIN and E0PIO                           */
-
-	orr	r4,	r4,	#(MDREFR_E1PIN|MDREFR_E0PIN)
-
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,     [r1, #MDREFR_OFFSET]
-
-
-	/* Step 4d: write MDCNFG with MDCNFG:DEx deasserted (set to 0), to  */
-	/*          configure but not enable each SDRAM partition pair.     */
-
-	ldr	r4,	=CONFIG_SYS_MDCNFG_VAL
-	bic	r4,	r4,	#(MDCNFG_DE0|MDCNFG_DE1)
-
-	str     r4,     [r1, #MDCNFG_OFFSET]	/* write back MDCNFG        */
-	ldr     r4,     [r1, #MDCNFG_OFFSET]
-
-
-	/* Step 4e: Wait for the clock to the SDRAMs to stabilize,          */
-	/*          100..200 µsec.                                          */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	ldr r2, [r3]
-	cmp r4, r2
-	bgt 1b
-
-
-	/* Step 4f: Trigger a number (usually 8) refresh cycles by          */
-	/*          attempting non-burst read or write accesses to disabled */
-	/*          SDRAM, as commonly specified in the power up sequence   */
-	/*          documented in SDRAM data sheets. The address(es) used   */
-	/*          for this purpose must not be cacheable.                 */
-
-	/*          There should 9 writes, since the first write doesn't    */
-	/*          trigger a refresh cycle on PXA250. See Intel PXA250 and */
-	/*          PXA210 Processors Specification Update,                 */
-	/*          Jan 2003, Errata #116, page 30.                         */
-
-
-	ldr	r3,	=CONFIG_SYS_DRAM_BASE
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-	str	r2, [r3]
-
-	/* Step 4g: Write MDCNFG with enable bits asserted                  */
-	/*          (MDCNFG:DEx set to 1).                                  */
-
-	ldr	r3, [r1, #MDCNFG_OFFSET]
-	orr	r3,	r3,	#(MDCNFG_DE0|MDCNFG_DE1)
-	str	r3, [r1, #MDCNFG_OFFSET]
-
-	/* Step 4h: Write MDMRS.                                            */
-
-	ldr     r2,  =CONFIG_SYS_MDMRS_VAL
-	str     r2,  [r1, #MDMRS_OFFSET]
-
-
-	/* We are finished with Intel's memory controller initialisation    */
-
-	/* ---------------------------------------------------------------- */
-	/* Disable (mask) all interrupts at interrupt controller            */
-	/* ---------------------------------------------------------------- */
-
-initirqs:
-
-	mov     r1, #0		/* clear int. level register (IRQ, not FIQ) */
-	ldr     r2,  =ICLR
-	str     r1,  [r2]
-
-	ldr     r2,  =ICMR	/* mask all interrupts at the controller    */
-	str     r1,  [r2]
-
-
-	/* ---------------------------------------------------------------- */
-	/* Clock initialisation                                             */
-	/* ---------------------------------------------------------------- */
-
-initclks:
-
-	/* Disable the peripheral clocks, and set the core clock frequency  */
-	/* (hard-coding at 398.12MHz for now).                              */
-
-	/* Turn Off ALL on-chip peripheral clocks for re-configuration      */
-	/* Note: See label 'ENABLECLKS' for the re-enabling                 */
-	ldr     r1,  =CKEN
-	mov     r2,  #0
-	str     r2,  [r1]
-
-
-	/* default value in case no valid rotary switch setting is found    */
-	ldr     r2, =(CCCR_L27|CCCR_M2|CCCR_N10)  /* DEFAULT: {200/200/100} */
-
-	/* ... and write the core clock config register                     */
-	ldr     r1,  =CCCR
-	str     r2,  [r1]
-
-	/* enable the 32Khz oscillator for RTC and PowerManager             */
-/*
-	ldr     r1,  =OSCC
-	mov     r2,  #OSCC_OON
-	str     r2,  [r1]
-*/
-	/* NOTE:  spin here until OSCC.OOK get set, meaning the PLL         */
-	/* has settled.                                                     */
-60:
-	ldr     r2, [r1]
-	ands    r2, r2, #1
-	beq     60b
-
-	/* ---------------------------------------------------------------- */
-	/*                                                                  */
-	/* ---------------------------------------------------------------- */
-
-	/* Save SDRAM size                                                  */
-	ldr	r1, =DRAM_SIZE
-	str	r8, [r1]
-
-	/* Interrupt init: Mask all interrupts                              */
-	ldr	r0, =ICMR			/* enable no sources        */
-	mov	r1, #0
-	str	r1, [r0]
-
-	/* FIXME */
-
-#ifndef DEBUG
-	/*Disable software and data breakpoints */
-	mov	r0,#0
-	mcr	p15,0,r0,c14,c8,0  /* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0  /* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0  /* dbcon */
-
-	/*Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0  /* dcsr */
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* End lowlevel_init                                                     */
-	/* ---------------------------------------------------------------- */
-
-endlowlevel_init:
-
-    mov     pc, lr
diff --git a/board/lubbock/Makefile b/board/lubbock/Makefile
index 6592307..2853bca 100644
--- a/board/lubbock/Makefile
+++ b/board/lubbock/Makefile
@@ -27,17 +27,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= lubbock.o flash.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/lubbock/config.mk b/board/lubbock/config.mk
deleted file mode 100644
index f30f695..0000000
--- a/board/lubbock/config.mk
+++ /dev/null
@@ -1,3 +0,0 @@
-#CONFIG_SYS_TEXT_BASE = 0xa1700000
-CONFIG_SYS_TEXT_BASE = 0xa3080000
-#CONFIG_SYS_TEXT_BASE = 0
diff --git a/board/lubbock/lowlevel_init.S b/board/lubbock/lowlevel_init.S
deleted file mode 100644
index db6f69d..0000000
--- a/board/lubbock/lowlevel_init.S
+++ /dev/null
@@ -1,411 +0,0 @@
-/*
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * NOTE: I haven't clean this up considerably, just enough to get it
- * running. See hal_platform_setup.h for the source. See
- * board/cradle/lowlevel_init.S for another PXA250 setup that is
- * much cleaner.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-/* wait for coprocessor write complete */
-   .macro CPWAIT reg
-   mrc  p15,0,\reg,c2,c0,0
-   mov  \reg,\reg
-   sub  pc,pc,#4
-   .endm
-
-
-/*
- *	Memory setup
- */
-
-.globl lowlevel_init
-lowlevel_init:
-
-    mov      r10, lr
-
-	/* Set up GPIO pins first ----------------------------------------- */
-
-	ldr		r0,	=GPSR0
-	ldr		r1,	=CONFIG_SYS_GPSR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR1
-	ldr		r1,	=CONFIG_SYS_GPSR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR2
-	ldr		r1,	=CONFIG_SYS_GPSR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR0
-	ldr		r1,	=CONFIG_SYS_GPCR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR1
-	ldr		r1,	=CONFIG_SYS_GPCR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR2
-	ldr		r1,	=CONFIG_SYS_GPCR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR0
-	ldr		r1,	=CONFIG_SYS_GPDR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR1
-	ldr		r1,	=CONFIG_SYS_GPDR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR2
-	ldr		r1,	=CONFIG_SYS_GPDR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_L
-	ldr		r1,	=CONFIG_SYS_GAFR0_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_U
-	ldr		r1,	=CONFIG_SYS_GAFR0_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_L
-	ldr		r1,	=CONFIG_SYS_GAFR1_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_U
-	ldr		r1,	=CONFIG_SYS_GAFR1_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_L
-	ldr		r1,	=CONFIG_SYS_GAFR2_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_U
-	ldr		r1,	=CONFIG_SYS_GAFR2_U_VAL
-	str		r1,   [r0]
-
-	ldr	r0,	=PSSR		/* enable GPIO pins */
-	ldr		r1,	=CONFIG_SYS_PSSR_VAL
-	str		r1,   [r0]
-
-	/* ---------------------------------------------------------------- */
-	/* Enable memory interface                                          */
-	/*                                                                  */
-	/* The sequence below is based on the recommended init steps        */
-	/* detailed in the Intel PXA250 Operating Systems Developers Guide, */
-	/* Chapter 10.                                                      */
-	/* ---------------------------------------------------------------- */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 1: Wait for at least 200 microsedonds to allow internal     */
-	/*         clocks to settle. Only necessary after hard reset...     */
-	/*         FIXME: can be optimized later                            */
-	/* ---------------------------------------------------------------- */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	ldr r2, [r3]
-	cmp r4, r2
-	bgt 1b
-
-mem_init:
-
-	ldr     r1,  =MEMC_BASE		/* get memory controller base addr. */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2a: Initialize Asynchronous static memory controller        */
-	/* ---------------------------------------------------------------- */
-
-	/* MSC registers: timing, bus width, mem type                       */
-
-	/* MSC0: nCS(0,1)                                                   */
-	ldr     r2,   =CONFIG_SYS_MSC0_VAL
-	str     r2,   [r1, #MSC0_OFFSET]
-	ldr     r2,   [r1, #MSC0_OFFSET]	/* read back to ensure      */
-						/* that data latches        */
-	/* MSC1: nCS(2,3)                                                   */
-	ldr     r2,  =CONFIG_SYS_MSC1_VAL
-	str     r2,  [r1, #MSC1_OFFSET]
-	ldr     r2,  [r1, #MSC1_OFFSET]
-
-	/* MSC2: nCS(4,5)                                                   */
-	ldr     r2,  =CONFIG_SYS_MSC2_VAL
-	str     r2,  [r1, #MSC2_OFFSET]
-	ldr     r2,  [r1, #MSC2_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2b: Initialize Card Interface                               */
-	/* ---------------------------------------------------------------- */
-
-	/* MECR: Memory Expansion Card Register                             */
-	ldr     r2,  =CONFIG_SYS_MECR_VAL
-	str     r2,  [r1, #MECR_OFFSET]
-	ldr	r2,	[r1, #MECR_OFFSET]
-
-	/* MCMEM0: Card Interface slot 0 timing                             */
-	ldr     r2,  =CONFIG_SYS_MCMEM0_VAL
-	str     r2,  [r1, #MCMEM0_OFFSET]
-	ldr	r2,	[r1, #MCMEM0_OFFSET]
-
-	/* MCMEM1: Card Interface slot 1 timing                             */
-	ldr     r2,  =CONFIG_SYS_MCMEM1_VAL
-	str     r2,  [r1, #MCMEM1_OFFSET]
-	ldr	r2,	[r1, #MCMEM1_OFFSET]
-
-	/* MCATT0: Card Interface Attribute Space Timing, slot 0            */
-	ldr     r2,  =CONFIG_SYS_MCATT0_VAL
-	str     r2,  [r1, #MCATT0_OFFSET]
-	ldr	r2,	[r1, #MCATT0_OFFSET]
-
-	/* MCATT1: Card Interface Attribute Space Timing, slot 1            */
-	ldr     r2,  =CONFIG_SYS_MCATT1_VAL
-	str     r2,  [r1, #MCATT1_OFFSET]
-	ldr	r2,	[r1, #MCATT1_OFFSET]
-
-	/* MCIO0: Card Interface I/O Space Timing, slot 0                   */
-	ldr     r2,  =CONFIG_SYS_MCIO0_VAL
-	str     r2,  [r1, #MCIO0_OFFSET]
-	ldr	r2,	[r1, #MCIO0_OFFSET]
-
-	/* MCIO1: Card Interface I/O Space Timing, slot 1                   */
-	ldr     r2,  =CONFIG_SYS_MCIO1_VAL
-	str     r2,  [r1, #MCIO1_OFFSET]
-	ldr	r2,	[r1, #MCIO1_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2c: Write FLYCNFG  FIXME: what's that???                    */
-	/* ---------------------------------------------------------------- */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2d: Initialize Timing for Sync Memory (SDCLK0)              */
-	/* ---------------------------------------------------------------- */
-
-	/* Before accessing MDREFR we need a valid DRI field, so we set     */
-	/* this to power on defaults + DRI field.                           */
-
-	ldr     r3,     =CONFIG_SYS_MDREFR_VAL
-	ldr     r2,     =0xFFF
-	and     r3,     r3,  r2
-	ldr	r4,	=0x03ca4000
-	orr     r4,     r4,  r3
-	str	r4,	[r1, #MDREFR_OFFSET]	/* write back MDREFR        */
-	ldr     r4,  [r1, #MDREFR_OFFSET]
-
-	/* Note: preserve the mdrefr value in r4                            */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */
-	/* ---------------------------------------------------------------- */
-
-	/* Initialize SXCNFG register. Assert the enable bits               */
-
-	/* Write SXMRS to cause an MRS command to all enabled banks of      */
-	/* synchronous static memory. Note that SXLCR need not be written   */
-	/* at this time.                                                    */
-
-	/* FIXME: we use async mode for now                                 */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 4: Initialize SDRAM                                         */
-	/* ---------------------------------------------------------------- */
-
-	/* set MDREFR according to user define with exception of a few bits */
-
-	ldr     r4,     =CONFIG_SYS_MDREFR_VAL
-	orr	r4,	r4,	#(MDREFR_SLFRSH)
-	bic	r4,	r4,	#(MDREFR_E1PIN|MDREFR_E0PIN)
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,  [r1, #MDREFR_OFFSET]
-
-	/* Step 4b: de-assert MDREFR:SLFRSH.                                */
-
-	bic	r4,	r4,	#(MDREFR_SLFRSH)
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,  [r1, #MDREFR_OFFSET]
-
-
-	/* Step 4c: assert MDREFR:E1PIN and E0PIO as desired                */
-
-	ldr     r4,     =CONFIG_SYS_MDREFR_VAL
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,     [r1, #MDREFR_OFFSET]
-
-
-	/* Step 4d: write MDCNFG with MDCNFG:DEx deasserted (set to 0), to  */
-	/*          configure but not enable each SDRAM partition pair.     */
-
-	ldr	r4,	=CONFIG_SYS_MDCNFG_VAL
-	bic	r4,	r4,	#(MDCNFG_DE0|MDCNFG_DE1)
-
-	str     r4,     [r1, #MDCNFG_OFFSET]	/* write back MDCNFG        */
-	ldr     r4,     [r1, #MDCNFG_OFFSET]
-
-
-	/* Step 4e: Wait for the clock to the SDRAMs to stabilize,          */
-	/*          100..200 µsec.                                          */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	    str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	    ldr r2, [r3]
-	    cmp r4, r2
-	    bgt 1b
-
-
-	/* Step 4f: Trigger a number (usually 8) refresh cycles by          */
-	/*          attempting non-burst read or write accesses to disabled */
-	/*          SDRAM, as commonly specified in the power up sequence   */
-	/*          documented in SDRAM data sheets. The address(es) used   */
-	/*          for this purpose must not be cacheable.                 */
-
-	ldr	r3,	=CONFIG_SYS_DRAM_BASE
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-
-
-	/* Step 4g: Write MDCNFG with enable bits asserted                  */
-	/*          (MDCNFG:DEx set to 1).                                  */
-
-	ldr     r3,  [r1, #MDCNFG_OFFSET]
-	orr	r3,	r3,	#(MDCNFG_DE0|MDCNFG_DE1)
-	str     r3,  [r1, #MDCNFG_OFFSET]
-
-	/* Step 4h: Write MDMRS.                                            */
-
-	ldr     r2,  =CONFIG_SYS_MDMRS_VAL
-	str     r2,  [r1, #MDMRS_OFFSET]
-
-
-	/* We are finished with Intel's memory controller initialisation    */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Disable (mask) all interrupts at interrupt controller            */
-	/* ---------------------------------------------------------------- */
-
-initirqs:
-
-	mov     r1, #0		/* clear int. level register (IRQ, not FIQ) */
-	ldr     r2,  =ICLR
-	str     r1,  [r2]
-
-	ldr     r2,  =ICMR	/* mask all interrupts at the controller    */
-	str     r1,  [r2]
-
-
-	/* ---------------------------------------------------------------- */
-	/* Clock initialisation                                             */
-	/* ---------------------------------------------------------------- */
-
-initclks:
-
-	/* Disable the peripheral clocks, and set the core clock frequency  */
-	/* (hard-coding at 398.12MHz for now).                              */
-
-	/* Turn Off ALL on-chip peripheral clocks for re-configuration      */
-	/* Note: See label 'ENABLECLKS' for the re-enabling                 */
-	ldr     r1,  =CKEN
-	mov     r2,  #0
-	str     r2,  [r1]
-
-
-	/* default value in case no valid rotary switch setting is found    */
-	ldr     r2, =(CCCR_L27|CCCR_M2|CCCR_N10)  /* DEFAULT: {200/200/100} */
-
-	/* ... and write the core clock config register                     */
-	ldr     r1,  =CCCR
-	str     r2,  [r1]
-
-#ifdef RTC
-	/* enable the 32Khz oscillator for RTC and PowerManager             */
-
-	ldr     r1,  =OSCC
-	mov     r2,  #OSCC_OON
-	str     r2,  [r1]
-
-	/* NOTE:  spin here until OSCC.OOK get set, meaning the PLL         */
-	/* has settled.                                                     */
-60:
-	ldr     r2, [r1]
-	ands    r2, r2, #1
-	beq     60b
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/*                                                                  */
-	/* ---------------------------------------------------------------- */
-
-	/* Save SDRAM size */
-    ldr     r1, =DRAM_SIZE
-	 str	   r8, [r1]
-
-	/* Interrupt init: Mask all interrupts                              */
-    ldr	r0, =ICMR /* enable no sources */
-	mov r1, #0
-    str r1, [r0]
-
-	/* FIXME */
-
-#define NODEBUG
-#ifdef NODEBUG
-	/*Disable software and data breakpoints */
-	mov	r0,#0
-	mcr	p15,0,r0,c14,c8,0  /* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0  /* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0  /* dbcon */
-
-	/*Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0  /* dcsr */
-
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* End lowlevel_init                                                     */
-	/* ---------------------------------------------------------------- */
-
-endlowlevel_init:
-
-    mov     pc, lr
diff --git a/board/lubbock/lubbock.c b/board/lubbock/lubbock.c
index d8d6ffb..f791c5b 100644
--- a/board/lubbock/lubbock.c
+++ b/board/lubbock/lubbock.c
@@ -36,8 +36,9 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int board_init (void)
 {
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
 
 	/* arch number of Lubbock-Board */
 	gd->bd->bi_arch_number = MACH_TYPE_LUBBOCK;
@@ -55,19 +56,18 @@ int board_late_init(void)
 	return 0;
 }
 
+extern void pxa_dram_init(void);
+int dram_init(void)
+{
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
 
-int dram_init (void)
+void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
-	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
-	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
-
-	return 0;
 }
 
 #ifdef CONFIG_CMD_NET
diff --git a/board/palmld/Makefile b/board/palmld/Makefile
index bcb014d..0cca8ab 100644
--- a/board/palmld/Makefile
+++ b/board/palmld/Makefile
@@ -24,17 +24,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= palmld.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/palmld/config.mk b/board/palmld/config.mk
deleted file mode 100644
index 1d650ac..0000000
--- a/board/palmld/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-TEXT_BASE = 0xa1000000
diff --git a/board/palmld/lowlevel_init.S b/board/palmld/lowlevel_init.S
deleted file mode 100644
index e3382ee..0000000
--- a/board/palmld/lowlevel_init.S
+++ /dev/null
@@ -1,45 +0,0 @@
-/*
- * Palm LifeDrive Lowlevel Hardware Initialization
- *
- * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/macro.h>
-
-.globl lowlevel_init
-lowlevel_init:
-	pxa_gpio_setup
-
-	/* Enable GPIO reset */
-	ldr	r0, =PCFR
-	mov	r1, #0x30
-	str	r1, [r0]
-
-	pxa_wait_ticks	0x8000
-	pxa_mem_setup
-	pxa_wakeup
-	pxa_intr_setup
-	pxa_clock_setup
-
-	mov	pc, lr
diff --git a/board/palmld/palmld.c b/board/palmld/palmld.c
index 4f0087e..5588fe7 100644
--- a/board/palmld/palmld.c
+++ b/board/palmld/palmld.c
@@ -33,7 +33,11 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int board_init(void)
 {
-	/* arch number of Lubbock-Board */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
+
+	/* arch number of PalmLD */
 	gd->bd->bi_arch_number = MACH_TYPE_PALMLD;
 
 	/* adress of boot parameters */
@@ -52,12 +56,18 @@ struct serial_device *default_serial_console(void)
 	return &serial_ffuart_device;
 }
 
+extern void pxa_dram_init(void);
 int dram_init(void)
 {
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
 }
 
 ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
diff --git a/board/palmld/u-boot.lds b/board/palmld/u-boot.lds
deleted file mode 100644
index fb4358b..0000000
--- a/board/palmld/u-boot.lds
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
-	. = 0x00000000;
-
-	. = ALIGN(4);
-	.text      :
-	{
-	  cpu/pxa/start.o	(.text)
-	  *(.text)
-	}
-
-	. = ALIGN(4);
-	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
-
-	. = ALIGN(4);
-	.data : { *(.data) }
-
-	. = ALIGN(4);
-	.got : { *(.got) }
-
-	. = .;
-	__u_boot_cmd_start = .;
-	.u_boot_cmd : { *(.u_boot_cmd) }
-	__u_boot_cmd_end = .;
-
-	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
-}
diff --git a/board/palmtc/Makefile b/board/palmtc/Makefile
index 20ac4e1..3a12e66 100644
--- a/board/palmtc/Makefile
+++ b/board/palmtc/Makefile
@@ -24,17 +24,16 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= palmtc.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/palmtc/config.mk b/board/palmtc/config.mk
deleted file mode 100644
index 1d650ac..0000000
--- a/board/palmtc/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-TEXT_BASE = 0xa1000000
diff --git a/board/palmtc/lowlevel_init.S b/board/palmtc/lowlevel_init.S
deleted file mode 100644
index 74050dc..0000000
--- a/board/palmtc/lowlevel_init.S
+++ /dev/null
@@ -1,39 +0,0 @@
-/*
- * Palm Tungsten|C Lowlevel Hardware Initialization
- *
- * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/macro.h>
-
-.globl lowlevel_init
-lowlevel_init:
-	pxa_gpio_setup
-	pxa_wait_ticks	0x8000
-	pxa_mem_setup
-	pxa_wakeup
-	pxa_intr_setup
-	pxa_clock_setup
-
-	mov	pc, lr
diff --git a/board/palmtc/palmtc.c b/board/palmtc/palmtc.c
index 04cb33e..25186ae 100644
--- a/board/palmtc/palmtc.c
+++ b/board/palmtc/palmtc.c
@@ -32,6 +32,10 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int board_init(void)
 {
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
+
 	/* Arch number of Palm Tungsten|C */
 	gd->bd->bi_arch_number = MACH_TYPE_PALMTC;
 
@@ -51,9 +55,16 @@ struct serial_device *default_serial_console(void)
 	return &serial_ffuart_device;
 }
 
+extern void pxa_dram_init(void);
 int dram_init(void)
 {
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-	return 0;
 }
diff --git a/board/palmtc/u-boot.lds b/board/palmtc/u-boot.lds
deleted file mode 100644
index fb4358b..0000000
--- a/board/palmtc/u-boot.lds
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
-	. = 0x00000000;
-
-	. = ALIGN(4);
-	.text      :
-	{
-	  cpu/pxa/start.o	(.text)
-	  *(.text)
-	}
-
-	. = ALIGN(4);
-	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
-
-	. = ALIGN(4);
-	.data : { *(.data) }
-
-	. = ALIGN(4);
-	.got : { *(.got) }
-
-	. = .;
-	__u_boot_cmd_start = .;
-	.u_boot_cmd : { *(.u_boot_cmd) }
-	__u_boot_cmd_end = .;
-
-	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
-}
diff --git a/board/pleb2/Makefile b/board/pleb2/Makefile
index faa2691..cb0c3d7 100644
--- a/board/pleb2/Makefile
+++ b/board/pleb2/Makefile
@@ -27,17 +27,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= pleb2.o flash.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/pleb2/config.mk b/board/pleb2/config.mk
deleted file mode 100644
index 079f58e..0000000
--- a/board/pleb2/config.mk
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_SYS_TEXT_BASE =  0xa1F80000
-#CONFIG_SYS_TEXT_BASE = 0xa3080000
-#CONFIG_SYS_TEXT_BASE = 0
diff --git a/board/pleb2/lowlevel_init.S b/board/pleb2/lowlevel_init.S
deleted file mode 100644
index b95ff9c..0000000
--- a/board/pleb2/lowlevel_init.S
+++ /dev/null
@@ -1,488 +0,0 @@
-/*
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-/* wait for coprocessor write complete */
-	.macro CPWAIT reg
-	mrc	p15,0,\reg,c2,c0,0
-	mov	\reg,\reg
-	sub	pc,pc,#4
-	.endm
-
-.globl lowlevel_init
-lowlevel_init:
-
-	mov	r10, lr
-
-	/* Set up GPIO pins first */
-
-	ldr	r0,   =GPSR0
-	ldr	r1,   =CONFIG_SYS_GPSR0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPSR1
-	ldr	r1,   =CONFIG_SYS_GPSR1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPSR2
-	ldr	r1,   =CONFIG_SYS_GPSR2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPCR0
-	ldr	r1,   =CONFIG_SYS_GPCR0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPCR1
-	ldr	r1,   =CONFIG_SYS_GPCR1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPCR2
-	ldr	r1,   =CONFIG_SYS_GPCR2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GRER0
-	ldr	r1,   =CONFIG_SYS_GRER0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GRER1
-	ldr	r1,   =CONFIG_SYS_GRER1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GRER2
-	ldr	r1,   =CONFIG_SYS_GRER2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GFER0
-	ldr	r1,   =CONFIG_SYS_GFER0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GFER1
-	ldr	r1,   =CONFIG_SYS_GFER1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GFER2
-	ldr	r1,   =CONFIG_SYS_GFER2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPDR0
-	ldr	r1,   =CONFIG_SYS_GPDR0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPDR1
-	ldr	r1,   =CONFIG_SYS_GPDR1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPDR2
-	ldr	r1,   =CONFIG_SYS_GPDR2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR0_L
-	ldr	r1,   =CONFIG_SYS_GAFR0_L_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR0_U
-	ldr	r1,   =CONFIG_SYS_GAFR0_U_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR1_L
-	ldr	r1,   =CONFIG_SYS_GAFR1_L_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR1_U
-	ldr	r1,   =CONFIG_SYS_GAFR1_U_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR2_L
-	ldr	r1,   =CONFIG_SYS_GAFR2_L_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR2_U
-	ldr	r1,   =CONFIG_SYS_GAFR2_U_VAL
-	str	r1,   [r0]
-
-	/* enable GPIO pins */
-	ldr	r0,   =PSSR
-	ldr	r1,   =CONFIG_SYS_PSSR_VAL
-	str	r1,   [r0]
-
-
-/*********************************************************************
-    Initlialize Memory Controller
-
-    See PXA250 Operating System Developer's Guide
-
-    pause for 200 uSecs- allow internal clocks to settle
-    *Note: only need this if hard reset... doing it anyway for now
-*/
-
-	@ Step 1
-	@ ---- Wait 200 usec
-	ldr	r3, =OSCR	@ reset the OS Timer Count to zero
-	mov	r2, #0
-	str	r2, [r3]
-	ldr	r4, =0x300	@ really 0x2E1 is about 200usec, so 0x300 should be plenty
-1:
-	ldr	r2, [r3]
-	cmp	r4, r2
-	bgt	1b
-
-mem_init:
-	@ get memory controller base address
-	ldr	r1,  =MEMC_BASE
-
-@****************************************************************************
-@  Step 2
-@
-
-	@ Step 2a
-	@ write msc0, read back to ensure data latches
-	@
-	ldr	r2,   =CONFIG_SYS_MSC0_VAL
-	str	r2,   [r1, #MSC0_OFFSET]
-	ldr	r2,   [r1, #MSC0_OFFSET]
-
-	@ write msc1
-	ldr	r2,  =CONFIG_SYS_MSC1_VAL
-	str	r2,  [r1, #MSC1_OFFSET]
-	ldr	r2,  [r1, #MSC1_OFFSET]
-
-	@ write msc2
-	ldr	r2,  =CONFIG_SYS_MSC2_VAL
-	str	r2,  [r1, #MSC2_OFFSET]
-	ldr	r2,  [r1, #MSC2_OFFSET]
-
-
-@ Step 2b
-	@ write mecr
-	ldr	r2,  =CONFIG_SYS_MECR_VAL
-	str	r2,  [r1, #MECR_OFFSET]
-
-	@ write mcmem0
-	ldr	r2,  =CONFIG_SYS_MCMEM0_VAL
-	str	r2,  [r1, #MCMEM0_OFFSET]
-
-	@ write mcmem1
-	ldr	r2,  =CONFIG_SYS_MCMEM1_VAL
-	str	r2,  [r1, #MCMEM1_OFFSET]
-
-	@ write mcatt0
-	ldr	r2,  =CONFIG_SYS_MCATT0_VAL
-	str	r2,  [r1, #MCATT0_OFFSET]
-
-	@ write mcatt1
-	ldr	r2,  =CONFIG_SYS_MCATT1_VAL
-	str	r2,  [r1, #MCATT1_OFFSET]
-
-	@ write mcio0
-	ldr	r2,  =CONFIG_SYS_MCIO0_VAL
-	str	r2,  [r1, #MCIO0_OFFSET]
-
-	@ write mcio1
-	ldr	r2,  =CONFIG_SYS_MCIO1_VAL
-	str	r2,  [r1, #MCIO1_OFFSET]
-
-@ Step 2c
-	@ fly-by-dma is defeatured on this part
-	@ write flycnfg
-	@ldr	r2,  =CONFIG_SYS_FLYCNFG_VAL
-	@str	r2,  [r1, #FLYCNFG_OFFSET]
-
-/* FIXME Does this sequence really make sense */
-#ifdef REDBOOT_WAY
-	@ Step 2d
-	@ get the mdrefr settings
-	ldr	r3,  =CONFIG_SYS_MDREFR_VAL
-
-	@ extract DRI field (we need a valid DRI field)
-	@
-	ldr	r2,  =0xFFF
-
-	@ valid DRI field in r3
-	@
-	and	r3,  r3,  r2
-
-	@ get the reset state of MDREFR
-	@
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-
-	@ clear the DRI field
-	@
-	bic	r4,  r4,  r2
-
-	@ insert the valid DRI field loaded above
-	@
-	orr	r4,  r4,  r3
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-
-	@ *Note: preserve the mdrefr value in r4 *
-
-@****************************************************************************
-@  Step 3
-@
-@ NO SRAM
-
-	mov	pc, r10
-
-
-@****************************************************************************
-@  Step 4
-@
-
-	@ Assumes previous mdrefr value in r4, if not then read current mdrefr
-
-	@ clear the free-running clock bits
-	@ (clear K0Free, K1Free, K2Free
-	@
-	bic	r4,  r4,  #(0x00800000 | 0x01000000 | 0x02000000)
-
-	@ set K0RUN for CPLD clock
-	@
-	orr	r4,  r4,  #0x00002000
-
-	@ set K1RUN if bank 0 installed
-	@
-	orr	r4,  r4,  #0x00010000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-
-	@ deassert SLFRSH
-	@
-	bic	r4,  r4,  #0x00400000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-
-	@ assert E1PIN
-	@
-	orr	r4,  r4,  #0x00008000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-	nop
-	nop
-#else
-	@ Step 2d
-	@ get the mdrefr settings
-	ldr	r3,  =CONFIG_SYS_MDREFR_VAL
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-
-	@  Step 4
-
-	@ set K0RUN for CPLD clock
-	@
-	orr	r4,  r4,  #0x00002000
-
-	@ set K1RUN for bank 0
-	@
-	orr	r4,  r4,  #0x00010000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-
-	@ deassert SLFRSH
-	@
-	bic	r4,  r4,  #0x00400000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-
-	@ assert E1PIN
-	@
-	orr	r4,  r4,  #0x00008000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-	nop
-	nop
-#endif
-
-	@ Step 4d
-	@ fetch platform value of mdcnfg
-	@
-	ldr	r2,  =CONFIG_SYS_MDCNFG_VAL
-
-	@ disable all sdram banks
-	@
-	bic	r2,  r2,  #(MDCNFG_DE0 | MDCNFG_DE1)
-	bic	r2,  r2,  #(MDCNFG_DE2 | MDCNFG_DE3)
-
-	@ program banks 0/1 for bus width
-	@
-	bic	r2,  r2,  #MDCNFG_DWID0	     @0=32-bit
-
-	@ write initial value of mdcnfg, w/o enabling sdram banks
-	@
-	str	r2,  [r1, #MDCNFG_OFFSET]
-
-	@ Step 4e
-	@ pause for 200 uSecs
-	@
-	ldr	r3, =OSCR	@ reset the OS Timer Count to zero
-	mov	r2, #0
-	str	r2, [r3]
-	ldr	r4, =0x300			@ really 0x2E1 is about 200usec, so 0x300 should be plenty
-	1:
-	ldr	r2, [r3]
-	cmp	r4, r2
-	bgt	1b
-
-	/* Why is this here??? */
-	mov	r0, #0x78		 @turn everything off
-	mcr	p15, 0, r0, c1, c0, 0	   @(caches off, MMU off, etc.)
-
-	@ Step 4f
-	@ Access memory *not yet enabled* for CBR refresh cycles (8)
-	@ - CBR is generated for all banks
-
-	ldr	r2, =CONFIG_SYS_DRAM_BASE
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-
-	@ Step 4g
-	@get memory controller base address
-	@
-	ldr	r1,  =MEMC_BASE
-
-	@fetch current mdcnfg value
-	@
-	ldr	r3,  [r1, #MDCNFG_OFFSET]
-
-	@enable sdram bank 0 if installed (must do for any populated bank)
-	@
-	orr	r3,  r3,  #MDCNFG_DE0
-
-	@write back mdcnfg, enabling the sdram bank(s)
-	@
-	str	r3,  [r1, #MDCNFG_OFFSET]
-
-	@ Step 4h
-	@ write mdmrs
-	@
-	ldr	r2,  =CONFIG_SYS_MDMRS_VAL
-	str	r2,  [r1, #MDMRS_OFFSET]
-
-	@ Done Memory Init
-
-	/*SET_LED 6 */
-
-	@********************************************************************
-	@ Disable (mask) all interrupts at the interrupt controller
-	@
-
-	@ clear the interrupt level register (use IRQ, not FIQ)
-	@
-	mov	r1, #0
-	ldr	r2,  =ICLR
-	str	r1,  [r2]
-
-	@ Set interrupt mask register
-	@
-	ldr	r1,  =CONFIG_SYS_ICMR_VAL
-	ldr	r2,  =ICMR
-	str	r1,  [r2]
-
-	@ ********************************************************************
-	@ Disable the peripheral clocks, and set the core clock
-	@
-
-	@ Turn Off ALL on-chip peripheral clocks for re-configuration
-	@
-	ldr	r1,  =CKEN
-	mov	r2,  #0
-	str	r2,  [r1]
-
-	@ set core clocks
-	@
-	ldr	r2,  =CONFIG_SYS_CCCR_VAL
-	ldr	r1,  =CCCR
-	str	r2,  [r1]
-
-	#ifdef ENABLE32KHZ
-	@ enable the 32Khz oscillator for RTC and PowerManager
-	@
-	ldr	r1,  =OSCC
-	mov	r2,  #OSCC_OON
-	str	r2,  [r1]
-
-	@ NOTE:	 spin here until OSCC.OOK get set,
-	@	 meaning the PLL has settled.
-	@
-60:
-	ldr	r2, [r1]
-	ands	r2, r2, #1
-	beq	60b
-#endif
-
-	@ Turn on needed clocks
-	@
-	ldr	r1,  =CKEN
-	ldr	r2,  =CONFIG_SYS_CKEN_VAL
-	str	r2,  [r1]
-
-	/*SET_LED 7 */
-
-/* Is this needed???? */
-#define NODEBUG
-#ifdef NODEBUG
-   /*Disable software and data breakpoints */
-	mov	r0,#0
-	mcr	p15,0,r0,c14,c8,0  /* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0  /* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0  /* dbcon */
-
-	/*Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0  /* dcsr */
-
-#endif
-
-	mov	pc, r10
-
-@ End lowlevel_init
diff --git a/board/pleb2/pleb2.c b/board/pleb2/pleb2.c
index 97c37ea..5a16cc7 100644
--- a/board/pleb2/pleb2.c
+++ b/board/pleb2/pleb2.c
@@ -36,8 +36,9 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int board_init (void)
 {
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
 
 	/* arch number of Lubbock-Board */
 	gd->bd->bi_arch_number = MACH_TYPE_PLEB2;
@@ -55,17 +56,16 @@ int board_late_init(void)
 	return 0;
 }
 
+extern void pxa_dram_init(void);
+int dram_init(void)
+{
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
 
-int dram_init (void)
+void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
-	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
-	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
-
-	return 0;
 }
diff --git a/board/pxa255_idp/Makefile b/board/pxa255_idp/Makefile
index 4892b42..2835f37 100644
--- a/board/pxa255_idp/Makefile
+++ b/board/pxa255_idp/Makefile
@@ -27,17 +27,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= pxa_idp.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/pxa255_idp/config.mk b/board/pxa255_idp/config.mk
deleted file mode 100644
index f30f695..0000000
--- a/board/pxa255_idp/config.mk
+++ /dev/null
@@ -1,3 +0,0 @@
-#CONFIG_SYS_TEXT_BASE = 0xa1700000
-CONFIG_SYS_TEXT_BASE = 0xa3080000
-#CONFIG_SYS_TEXT_BASE = 0
diff --git a/board/pxa255_idp/lowlevel_init.S b/board/pxa255_idp/lowlevel_init.S
deleted file mode 100644
index a50760f..0000000
--- a/board/pxa255_idp/lowlevel_init.S
+++ /dev/null
@@ -1,496 +0,0 @@
-/*
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * NOTE: I haven't clean this up considerably, just enough to get it
- * running. See hal_platform_setup.h for the source. See
- * board/cradle/lowlevel_init.S for another PXA250 setup that is
- * much cleaner.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-/* wait for coprocessor write complete */
-	.macro CPWAIT reg
-	mrc  p15,0,\reg,c2,c0,0
-	mov  \reg,\reg
-	sub  pc,pc,#4
-	.endm
-
-/*
- *	Memory setup
- */
-.globl lowlevel_init
-lowlevel_init:
-
-	mov      r10, lr
-
-#ifdef DEBUG_BLINK_ENABLE
-	/* 3rd blink */
-	bl	blink
-#endif
-
-	/* Set up GPIO pins first ----------------------------------------- */
-	ldr		r0,	=GPSR0
-	ldr		r1,	=CONFIG_SYS_GPSR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR1
-	ldr		r1,	=CONFIG_SYS_GPSR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR2
-	ldr		r1,	=CONFIG_SYS_GPSR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR0
-	ldr		r1,	=CONFIG_SYS_GPCR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR1
-	ldr		r1,	=CONFIG_SYS_GPCR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR2
-	ldr		r1,	=CONFIG_SYS_GPCR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR0
-	ldr		r1,	=CONFIG_SYS_GPDR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR1
-	ldr		r1,	=CONFIG_SYS_GPDR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR2
-	ldr		r1,	=CONFIG_SYS_GPDR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_L
-	ldr		r1,	=CONFIG_SYS_GAFR0_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_U
-	ldr		r1,	=CONFIG_SYS_GAFR0_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_L
-	ldr		r1,	=CONFIG_SYS_GAFR1_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_U
-	ldr		r1,	=CONFIG_SYS_GAFR1_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_L
-	ldr		r1,	=CONFIG_SYS_GAFR2_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_U
-	ldr		r1,	=CONFIG_SYS_GAFR2_U_VAL
-	str		r1,   [r0]
-
-	ldr	r0,	=PSSR		/* enable GPIO pins */
-	ldr		r1,	=CONFIG_SYS_PSSR_VAL
-	str		r1,   [r0]
-
-#ifdef DEBUG_BLINK_ENABLE
-	/* 4th debug blink */
-	bl	blink
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* Enable memory interface                                          */
-	/*                                                                  */
-	/* The sequence below is based on the recommended init steps        */
-	/* detailed in the Intel PXA250 Operating Systems Developers Guide, */
-	/* Chapter 10.                                                      */
-	/* ---------------------------------------------------------------- */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 1: Wait for at least 200 microsedonds to allow internal     */
-	/*         clocks to settle. Only necessary after hard reset...     */
-	/*         FIXME: can be optimized later                            */
-	/* ---------------------------------------------------------------- */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	ldr r2, [r3]
-	cmp r4, r2
-	bgt 1b
-
-mem_init:
-
-	ldr     r1,  =MEMC_BASE		/* get memory controller base addr. */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2a: Initialize Asynchronous static memory controller        */
-	/* ---------------------------------------------------------------- */
-
-	/* MSC registers: timing, bus width, mem type                       */
-
-	/* MSC0: nCS(0,1)                                                   */
-	ldr     r2,   =CONFIG_SYS_MSC0_VAL
-	str     r2,   [r1, #MSC0_OFFSET]
-	ldr     r2,   [r1, #MSC0_OFFSET]	/* read back to ensure      */
-						/* that data latches        */
-	/* MSC1: nCS(2,3)                                                   */
-	ldr     r2,  =CONFIG_SYS_MSC1_VAL
-	str     r2,  [r1, #MSC1_OFFSET]
-	ldr     r2,  [r1, #MSC1_OFFSET]
-
-	/* MSC2: nCS(4,5)                                                   */
-	ldr     r2,  =CONFIG_SYS_MSC2_VAL
-	str     r2,  [r1, #MSC2_OFFSET]
-	ldr     r2,  [r1, #MSC2_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2b: Initialize Card Interface                               */
-	/* ---------------------------------------------------------------- */
-
-	/* MECR: Memory Expansion Card Register                             */
-	ldr     r2,  =CONFIG_SYS_MECR_VAL
-	str     r2,  [r1, #MECR_OFFSET]
-	ldr	r2,	[r1, #MECR_OFFSET]
-
-	/* MCMEM0: Card Interface slot 0 timing                             */
-	ldr     r2,  =CONFIG_SYS_MCMEM0_VAL
-	str     r2,  [r1, #MCMEM0_OFFSET]
-	ldr	r2,	[r1, #MCMEM0_OFFSET]
-
-	/* MCMEM1: Card Interface slot 1 timing                             */
-	ldr     r2,  =CONFIG_SYS_MCMEM1_VAL
-	str     r2,  [r1, #MCMEM1_OFFSET]
-	ldr	r2,	[r1, #MCMEM1_OFFSET]
-
-	/* MCATT0: Card Interface Attribute Space Timing, slot 0            */
-	ldr     r2,  =CONFIG_SYS_MCATT0_VAL
-	str     r2,  [r1, #MCATT0_OFFSET]
-	ldr	r2,	[r1, #MCATT0_OFFSET]
-
-	/* MCATT1: Card Interface Attribute Space Timing, slot 1            */
-	ldr     r2,  =CONFIG_SYS_MCATT1_VAL
-	str     r2,  [r1, #MCATT1_OFFSET]
-	ldr	r2,	[r1, #MCATT1_OFFSET]
-
-	/* MCIO0: Card Interface I/O Space Timing, slot 0                   */
-	ldr     r2,  =CONFIG_SYS_MCIO0_VAL
-	str     r2,  [r1, #MCIO0_OFFSET]
-	ldr	r2,	[r1, #MCIO0_OFFSET]
-
-	/* MCIO1: Card Interface I/O Space Timing, slot 1                   */
-	ldr     r2,  =CONFIG_SYS_MCIO1_VAL
-	str     r2,  [r1, #MCIO1_OFFSET]
-	ldr	r2,	[r1, #MCIO1_OFFSET]
-
-#ifdef DEBUG_BLINK_ENABLE
-	/* 5th blink */
-	bl	blink
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2c: Write FLYCNFG  FIXME: what's that???                    */
-	/* ---------------------------------------------------------------- */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2d: Initialize Timing for Sync Memory (SDCLK0)              */
-	/* ---------------------------------------------------------------- */
-
-	/* Before accessing MDREFR we need a valid DRI field, so we set     */
-	/* this to power on defaults + DRI field.                           */
-
-	ldr     r3,     =CONFIG_SYS_MDREFR_VAL
-	ldr     r2,     =0xFFF
-	and     r3,     r3,  r2
-	ldr	r4,	=0x03ca4000
-	orr     r4,     r4,  r3
-	str	r4,	[r1, #MDREFR_OFFSET]	/* write back MDREFR        */
-	ldr     r4,  [r1, #MDREFR_OFFSET]
-
-	/* Note: preserve the mdrefr value in r4                            */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */
-	/* ---------------------------------------------------------------- */
-
-	/* Initialize SXCNFG register. Assert the enable bits               */
-
-	/* Write SXMRS to cause an MRS command to all enabled banks of      */
-	/* synchronous static memory. Note that SXLCR need not be written   */
-	/* at this time.                                                    */
-
-	/* FIXME: we use async mode for now                                 */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 4: Initialize SDRAM                                         */
-	/* ---------------------------------------------------------------- */
-
-	/* set MDREFR according to user define with exception of a few bits */
-
-	ldr     r4,     =CONFIG_SYS_MDREFR_VAL
-	orr	r4,	r4,	#(MDREFR_SLFRSH)
-	bic	r4,	r4,	#(MDREFR_E1PIN|MDREFR_E0PIN)
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,  [r1, #MDREFR_OFFSET]
-
-	/* Step 4b: de-assert MDREFR:SLFRSH.                                */
-
-	bic	r4,	r4,	#(MDREFR_SLFRSH)
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,  [r1, #MDREFR_OFFSET]
-
-	/* Step 4c: assert MDREFR:E1PIN and E0PIO as desired                */
-
-	ldr     r4,     =CONFIG_SYS_MDREFR_VAL
-	str     r4,     [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
-	ldr     r4,     [r1, #MDREFR_OFFSET]
-
-
-	/* Step 4d: write MDCNFG with MDCNFG:DEx deasserted (set to 0), to  */
-	/*          configure but not enable each SDRAM partition pair.     */
-
-	ldr	r4,	=CONFIG_SYS_MDCNFG_VAL
-	bic	r4,	r4,	#(MDCNFG_DE0|MDCNFG_DE1)
-
-	str     r4,     [r1, #MDCNFG_OFFSET]	/* write back MDCNFG        */
-	ldr     r4,     [r1, #MDCNFG_OFFSET]
-
-	/* Step 4e: Wait for the clock to the SDRAMs to stabilize,          */
-	/*          100..200 µsec.                                          */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	    str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	    ldr r2, [r3]
-	    cmp r4, r2
-	    bgt 1b
-
-	/* Step 4f: Trigger a number (usually 8) refresh cycles by          */
-	/*          attempting non-burst read or write accesses to disabled */
-	/*          SDRAM, as commonly specified in the power up sequence   */
-	/*          documented in SDRAM data sheets. The address(es) used   */
-	/*          for this purpose must not be cacheable.                 */
-
-	ldr	r3,	=CONFIG_SYS_DRAM_BASE
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-
-	/* Step 4g: Write MDCNFG with enable bits asserted                  */
-	/*          (MDCNFG:DEx set to 1).                                  */
-
-	ldr     r3,  [r1, #MDCNFG_OFFSET]
-	orr	r3,	r3,	#(MDCNFG_DE0|MDCNFG_DE1)
-	str     r3,  [r1, #MDCNFG_OFFSET]
-
-	/* Step 4h: Write MDMRS.                                            */
-
-	ldr     r2,  =CONFIG_SYS_MDMRS_VAL
-	str     r2,  [r1, #MDMRS_OFFSET]
-
-	/* We are finished with Intel's memory controller initialisation    */
-#if 0
-	/* FIXME turn on serial ports */
-	/* look into moving this to board_init() */
-	ldr	r2, =(PXA_CS5_PHYS + 0x03C0002c)
-	mov	r3, #0x13
-	str	r3, [r2]
-#endif
-
-#ifdef DEBUG_BLINK_ENABLE
-	/* 6th blink */
-	bl	blink
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* Disable (mask) all interrupts at interrupt controller            */
-	/* ---------------------------------------------------------------- */
-
-initirqs:
-
-	mov     r1, #0		/* clear int. level register (IRQ, not FIQ) */
-	ldr     r2,  =ICLR
-	str     r1,  [r2]
-
-	ldr     r2,  =ICMR	/* mask all interrupts at the controller    */
-	str     r1,  [r2]
-
-	/* ---------------------------------------------------------------- */
-	/* Clock initialisation                                             */
-	/* ---------------------------------------------------------------- */
-
-initclks:
-
-	/* Disable the peripheral clocks, and set the core clock frequency  */
-	/* (hard-coding at 398.12MHz for now).                              */
-
-	/* Turn Off ALL on-chip peripheral clocks for re-configuration      */
-	/* Note: See label 'ENABLECLKS' for the re-enabling                 */
-#if 0
-	ldr     r1,  =CKEN
-	mov     r2,  #0
-	str     r2,  [r1]
-
-	/* default value in case no valid rotary switch setting is found    */
-	ldr     r2, =(CCCR_L27|CCCR_M2|CCCR_N10)  /* DEFAULT: {200/200/100} */
-
-	/* ... and write the core clock config register                     */
-	ldr     r1,  =CCCR
-	str     r2,  [r1]
-
-#endif
-
-#ifdef RTC
-	/* enable the 32Khz oscillator for RTC and PowerManager             */
-
-	ldr     r1,  =OSCC
-	mov     r2,  #OSCC_OON
-	str     r2,  [r1]
-
-	/* NOTE:  spin here until OSCC.OOK get set, meaning the PLL         */
-	/* has settled.                                                     */
-60:
-	ldr     r2, [r1]
-	ands    r2, r2, #1
-	beq     60b
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/*                                                                  */
-	/* ---------------------------------------------------------------- */
-
-	/* Save SDRAM size */
-	ldr     r1, =DRAM_SIZE
-	str     r8, [r1]
-
-	/* Interrupt init: Mask all interrupts                              */
-	ldr	r0, =ICMR /* enable no sources */
-	mov r1, #0
-	str r1, [r0]
-
-	/* FIXME */
-
-#define NODEBUG
-#ifdef NODEBUG
-	/*Disable software and data breakpoints */
-	mov	r0,#0
-	mcr	p15,0,r0,c14,c8,0  /* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0  /* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0  /* dbcon */
-
-	/*Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0  /* dcsr */
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* End memsetup                                                     */
-	/* ---------------------------------------------------------------- */
-
-#ifdef DEBUG_BLINK_ENABLE
-	/* 7th blink */
-	bl	blink
-#endif
-
-endlowlevel_init:
-
-	mov     pc, r10
-
-
-#ifdef DEBUG_BLINK_ENABLE
-
-/* debug LED code */
-
-/* delay about 200ms */
-delay:
-
-	/* reset OSCR to 0 */
-	ldr	r8, =OSCR
-	mov	r9, #0
-	str	r9, [r8]
-
-	/* make sure new value has stuck */
-1:
-	ldr	r8, =OSCR
-	ldr	r9, [r8]
-	mov	r8, #0x10000
-	cmp	r9, r8
-	bgt	1b
-
-	/* now, wait for delay to expire */
-1:
-	ldr	r8, =OSCR
-	ldr	r9, [r8]
-	mov	r8, #0xd4000
-	cmp	r8, r9
-	bgt	1b
-
-	mov	pc, lr
-
-/* blink code -- trashes r7, r8, r9 */
-
-.globl blink
-blink:
-
-	mov	r7, lr
-
-	/* set GPIO10 as outout */
-	ldr	r8,  =GPDR0
-	ldr	r9,  [r8]
-	orr	r9,  r9, #(1<<10)
-	str	r9,  [r8]
-
-	/* turn LED off */
-	mov	r9,  #(1<<10)
-	ldr	r8,  =GPCR0
-	str	r9, [r8]
-	bl	delay
-
-	/* turn LED on */
-	mov	r9,  #(1<<10)
-	ldr	r8,  =GPSR0
-	str	r9, [r8]
-	bl	delay
-
-	/* turn LED off */
-	mov	r9,  #(1<<10)
-	ldr	r8,  =GPCR0
-	str	r9, [r8]
-
-	mov	pc, r7
-
-#endif
diff --git a/board/pxa255_idp/pxa_idp.c b/board/pxa255_idp/pxa_idp.c
index 4ab8bd4..804d09c 100644
--- a/board/pxa255_idp/pxa_idp.c
+++ b/board/pxa255_idp/pxa_idp.c
@@ -43,8 +43,9 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int board_init (void)
 {
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
 
 	/* arch number of Lubbock-Board */
 	gd->bd->bi_arch_number = MACH_TYPE_PXA_IDP;
@@ -82,22 +83,20 @@ int board_late_init(void)
 	return 0;
 }
 
+extern void pxa_dram_init(void);
+int dram_init(void)
+{
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
 
-int dram_init (void)
+void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
-	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
-	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
-
-	return 0;
 }
 
-
 #ifdef DEBUG_BLINKC_ENABLE
 
 void delay_c(void)
diff --git a/board/renesas/sh7785lcr/config.mk b/board/renesas/sh7785lcr/config.mk
index 1a9038c..6853d2b 100644
--- a/board/renesas/sh7785lcr/config.mk
+++ b/board/renesas/sh7785lcr/config.mk
@@ -24,6 +24,8 @@
 #
 sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
 
-ifndef CONFIG_SYS_TEXT_BASE
+ifdef CONFIG_SH_32BIT
+CONFIG_SYS_TEXT_BASE = 0x8FF80000
+else
 CONFIG_SYS_TEXT_BASE = 0x0ff80000
 endif
diff --git a/board/trizepsiv/Makefile b/board/trizepsiv/Makefile
index 44c0d49..060ac89 100644
--- a/board/trizepsiv/Makefile
+++ b/board/trizepsiv/Makefile
@@ -26,17 +26,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= conxs.o eeprom.o
-SOBJS	:= lowlevel_init.o pxavoltage.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/trizepsiv/config.mk b/board/trizepsiv/config.mk
deleted file mode 100644
index f04eb74..0000000
--- a/board/trizepsiv/config.mk
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_SYS_TEXT_BASE =0xa1f00000
-# 0xa1700000
-#CONFIG_SYS_TEXT_BASE = 0
diff --git a/board/trizepsiv/conxs.c b/board/trizepsiv/conxs.c
index 0c67367..99f665b 100644
--- a/board/trizepsiv/conxs.c
+++ b/board/trizepsiv/conxs.c
@@ -104,8 +104,9 @@ void usb_board_stop(void)
 
 int board_init (void)
 {
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
 
 	/* arch number of ConXS Board */
 	gd->bd->bi_arch_number = 776;
@@ -138,18 +139,18 @@ struct serial_device *default_serial_console (void)
 	return &serial_ffuart_device;
 }
 
-int dram_init (void)
+extern void pxa_dram_init(void);
+int dram_init(void)
+{
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
+
+void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
-	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
-	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
-
-	return 0;
 }
 
 #ifdef CONFIG_DRIVER_DM9000
diff --git a/board/trizepsiv/lowlevel_init.S b/board/trizepsiv/lowlevel_init.S
deleted file mode 100644
index 128d554..0000000
--- a/board/trizepsiv/lowlevel_init.S
+++ /dev/null
@@ -1,503 +0,0 @@
-/*
- * This was originally from the Lubbock u-boot port.
- *
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * NOTE: I haven't clean this up considerably, just enough to get it
- * running. See hal_platform_setup.h for the source. See
- * board/cradle/lowlevel_init.S for another PXA250 setup that is
- * much cleaner.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-/* wait for coprocessor write complete */
-   .macro CPWAIT reg
-   mrc	p15,0,\reg,c2,c0,0
-   mov	\reg,\reg
-   sub	pc,pc,#4
-   .endm
-
-
-/*
- *	Memory setup
- */
-
-.globl lowlevel_init
-lowlevel_init:
-
-	/* Set up GPIO pins first ----------------------------------------- */
-
-	ldr		r0,	=GPSR0
-	ldr		r1,	=CONFIG_SYS_GPSR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR1
-	ldr		r1,	=CONFIG_SYS_GPSR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR2
-	ldr		r1,	=CONFIG_SYS_GPSR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPSR3
-	ldr		r1,	=CONFIG_SYS_GPSR3_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR0
-	ldr		r1,	=CONFIG_SYS_GPCR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR1
-	ldr		r1,	=CONFIG_SYS_GPCR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR2
-	ldr		r1,	=CONFIG_SYS_GPCR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPCR3
-	ldr		r1,	=CONFIG_SYS_GPCR3_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GRER0
-	ldr		r1,	=CONFIG_SYS_GRER0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GRER1
-	ldr		r1,	=CONFIG_SYS_GRER1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GRER2
-	ldr		r1,	=CONFIG_SYS_GRER2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GRER3
-	ldr		r1,	=CONFIG_SYS_GRER3_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GFER0
-	ldr		r1,	=CONFIG_SYS_GFER0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GFER1
-	ldr		r1,	=CONFIG_SYS_GFER1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GFER2
-	ldr		r1,	=CONFIG_SYS_GFER2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GFER3
-	ldr		r1,	=CONFIG_SYS_GFER3_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR0
-	ldr		r1,	=CONFIG_SYS_GPDR0_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR1
-	ldr		r1,	=CONFIG_SYS_GPDR1_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR2
-	ldr		r1,	=CONFIG_SYS_GPDR2_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GPDR3
-	ldr		r1,	=CONFIG_SYS_GPDR3_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_L
-	ldr		r1,	=CONFIG_SYS_GAFR0_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR0_U
-	ldr		r1,	=CONFIG_SYS_GAFR0_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_L
-	ldr		r1,	=CONFIG_SYS_GAFR1_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR1_U
-	ldr		r1,	=CONFIG_SYS_GAFR1_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_L
-	ldr		r1,	=CONFIG_SYS_GAFR2_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR2_U
-	ldr		r1,	=CONFIG_SYS_GAFR2_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR3_L
-	ldr		r1,	=CONFIG_SYS_GAFR3_L_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=GAFR3_U
-	ldr		r1,	=CONFIG_SYS_GAFR3_U_VAL
-	str		r1,   [r0]
-
-	ldr		r0,	=PSSR		/* enable GPIO pins */
-	ldr		r1,	=CONFIG_SYS_PSSR_VAL
-	str		r1,   [r0]
-
-	/* ---------------------------------------------------------------- */
-	/* Enable memory interface					    */
-	/*								    */
-	/* The sequence below is based on the recommended init steps	    */
-	/* detailed in the Intel PXA250 Operating Systems Developers Guide, */
-	/* Chapter 10.							    */
-	/* ---------------------------------------------------------------- */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 1: Wait for at least 200 microsedonds to allow internal	    */
-	/*	   clocks to settle. Only necessary after hard reset...	    */
-	/*	   FIXME: can be optimized later			    */
-	/* ---------------------------------------------------------------- */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty	    */
-1:
-	ldr r2, [r3]
-	cmp r4, r2
-	bgt 1b
-
-mem_init:
-
-	ldr	r1,  =MEMC_BASE		/* get memory controller base addr. */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2a: Initialize Asynchronous static memory controller	    */
-	/* ---------------------------------------------------------------- */
-
-	/* MSC registers: timing, bus width, mem type			    */
-
-	/* MSC0: nCS(0,1)						    */
-	ldr	r2,   =CONFIG_SYS_MSC0_VAL
-	str	r2,   [r1, #MSC0_OFFSET]
-	ldr	r2,   [r1, #MSC0_OFFSET]	/* read back to ensure	    */
-						/* that data latches	    */
-	/* MSC1: nCS(2,3)						    */
-	ldr	r2,  =CONFIG_SYS_MSC1_VAL
-	str	r2,  [r1, #MSC1_OFFSET]
-	ldr	r2,  [r1, #MSC1_OFFSET]
-
-	/* MSC2: nCS(4,5)						    */
-	ldr	r2,  =CONFIG_SYS_MSC2_VAL
-	str	r2,  [r1, #MSC2_OFFSET]
-	ldr	r2,  [r1, #MSC2_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2b: Initialize Card Interface				    */
-	/* ---------------------------------------------------------------- */
-
-	/* MECR: Memory Expansion Card Register				    */
-	ldr	r2,  =CONFIG_SYS_MECR_VAL
-	str	r2,  [r1, #MECR_OFFSET]
-	ldr	r2,	[r1, #MECR_OFFSET]
-
-	/* MCMEM0: Card Interface slot 0 timing				    */
-	ldr	r2,  =CONFIG_SYS_MCMEM0_VAL
-	str	r2,  [r1, #MCMEM0_OFFSET]
-	ldr	r2,	[r1, #MCMEM0_OFFSET]
-
-	/* MCMEM1: Card Interface slot 1 timing				    */
-	ldr	r2,  =CONFIG_SYS_MCMEM1_VAL
-	str	r2,  [r1, #MCMEM1_OFFSET]
-	ldr	r2,	[r1, #MCMEM1_OFFSET]
-
-	/* MCATT0: Card Interface Attribute Space Timing, slot 0	    */
-	ldr	r2,  =CONFIG_SYS_MCATT0_VAL
-	str	r2,  [r1, #MCATT0_OFFSET]
-	ldr	r2,	[r1, #MCATT0_OFFSET]
-
-	/* MCATT1: Card Interface Attribute Space Timing, slot 1	    */
-	ldr	r2,  =CONFIG_SYS_MCATT1_VAL
-	str	r2,  [r1, #MCATT1_OFFSET]
-	ldr	r2,	[r1, #MCATT1_OFFSET]
-
-	/* MCIO0: Card Interface I/O Space Timing, slot 0		    */
-	ldr	r2,  =CONFIG_SYS_MCIO0_VAL
-	str	r2,  [r1, #MCIO0_OFFSET]
-	ldr	r2,	[r1, #MCIO0_OFFSET]
-
-	/* MCIO1: Card Interface I/O Space Timing, slot 1		    */
-	ldr	r2,  =CONFIG_SYS_MCIO1_VAL
-	str	r2,  [r1, #MCIO1_OFFSET]
-	ldr	r2,	[r1, #MCIO1_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2c: Write FLYCNFG  FIXME: what's that???		    */
-	/* ---------------------------------------------------------------- */
-	ldr	r2,  =CONFIG_SYS_FLYCNFG_VAL
-	str	r2,  [r1, #FLYCNFG_OFFSET]
-	str	r2,	[r1, #FLYCNFG_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2d: Initialize Timing for Sync Memory (SDCLK0)		    */
-	/* ---------------------------------------------------------------- */
-
-	/* Before accessing MDREFR we need a valid DRI field, so we set	    */
-	/* this to power on defaults + DRI field.			    */
-
-	ldr	r4,	[r1, #MDREFR_OFFSET]
-	ldr	r2,	=0xFFF
-	bic	r4,	r4, r2
-
-	ldr	r3,	=CONFIG_SYS_MDREFR_VAL
-	and	r3,	r3,  r2
-
-	orr	r4,	r4, r3
-	str	r4,	[r1, #MDREFR_OFFSET]	/* write back MDREFR	    */
-
-	orr	r4,  r4, #MDREFR_K0RUN
-	orr	r4,  r4, #MDREFR_K0DB4
-	orr	r4,  r4, #MDREFR_K0FREE
-	orr	r4,  r4, #MDREFR_K0DB2
-	orr	r4,  r4, #MDREFR_K1DB2
-	bic	r4,  r4, #MDREFR_K1FREE
-	bic	r4,  r4, #MDREFR_K2FREE
-
-	str	r4,	[r1, #MDREFR_OFFSET]	/* write back MDREFR	    */
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-
-	/* Note: preserve the mdrefr value in r4			    */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */
-	/* ---------------------------------------------------------------- */
-
-	/* Initialize SXCNFG register. Assert the enable bits		    */
-
-	/* Write SXMRS to cause an MRS command to all enabled banks of	    */
-	/* synchronous static memory. Note that SXLCR need not be written   */
-	/* at this time.						    */
-
-	ldr	r2,  =CONFIG_SYS_SXCNFG_VAL
-	str	r2,  [r1, #SXCNFG_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 4: Initialize SDRAM					    */
-	/* ---------------------------------------------------------------- */
-
-	bic	r4, r4, #(MDREFR_K2FREE |MDREFR_K1FREE | MDREFR_K0FREE)
-
-	orr	r4, r4, #MDREFR_K1RUN
-	bic	r4, r4, #MDREFR_K2DB2
-	str	r4, [r1, #MDREFR_OFFSET]
-	ldr	r4, [r1, #MDREFR_OFFSET]
-
-	bic	r4, r4, #MDREFR_SLFRSH
-	str	r4, [r1, #MDREFR_OFFSET]
-	ldr	r4, [r1, #MDREFR_OFFSET]
-
-	orr	r4, r4, #MDREFR_E1PIN
-	str	r4, [r1, #MDREFR_OFFSET]
-	ldr	r4, [r1, #MDREFR_OFFSET]
-
-	nop
-	nop
-
-
-	/* Step 4d: write MDCNFG with MDCNFG:DEx deasserted (set to 0), to  */
-	/*	    configure but not enable each SDRAM partition pair.	    */
-
-	ldr	r4,	=CONFIG_SYS_MDCNFG_VAL
-	bic	r4,	r4,	#(MDCNFG_DE0|MDCNFG_DE1)
-	bic	r4,	r4,	#(MDCNFG_DE2|MDCNFG_DE3)
-
-	str	r4,	[r1, #MDCNFG_OFFSET]	/* write back MDCNFG	    */
-	ldr	r4,	[r1, #MDCNFG_OFFSET]
-
-
-	/* Step 4e: Wait for the clock to the SDRAMs to stabilize,	    */
-	/*	    100..200 µsec.					    */
-
-	ldr r3, =OSCR			/* reset the OS Timer Count to zero */
-	mov r2, #0
-	str r2, [r3]
-	ldr r4, =0x300			/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty	    */
-1:
-	    ldr r2, [r3]
-	    cmp r4, r2
-	    bgt 1b
-
-
-	/* Step 4f: Trigger a number (usually 8) refresh cycles by	    */
-	/*	    attempting non-burst read or write accesses to disabled */
-	/*	    SDRAM, as commonly specified in the power up sequence   */
-	/*	    documented in SDRAM data sheets. The address(es) used   */
-	/*	    for this purpose must not be cacheable.		    */
-
-	ldr	r3,	=CONFIG_SYS_DRAM_BASE
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-
-
-	/* Step 4g: Write MDCNFG with enable bits asserted		    */
-	/*	    (MDCNFG:DEx set to 1).				    */
-
-	ldr	r3,	[r1, #MDCNFG_OFFSET]
-	mov	r4, r3
-	orr	r3,	r3,	#MDCNFG_DE0
-	str	r3,	[r1, #MDCNFG_OFFSET]
-	mov	r0, r3
-
-	/* Step 4h: Write MDMRS.					    */
-
-	ldr	r2,  =CONFIG_SYS_MDMRS_VAL
-	str	r2,  [r1, #MDMRS_OFFSET]
-
-	/* enable APD */
-	ldr	r3,  [r1, #MDREFR_OFFSET]
-	orr	r3,  r3,  #MDREFR_APD
-	str	r3,  [r1, #MDREFR_OFFSET]
-
-	/* We are finished with Intel's memory controller initialisation    */
-
-
-setvoltage:
-
-	mov	r10,	lr
-	bl	initPXAvoltage	/* In case the board is rebooting with a    */
-	mov	lr,	r10	/* low voltage raise it up to a good one.   */
-
-#if 1
-	b initirqs
-#endif
-
-wakeup:
-	/* Are we waking from sleep? */
-	ldr	r0,	=RCSR
-	ldr	r1,	[r0]
-	and	r1,	r1, #(RCSR_GPR | RCSR_SMR | RCSR_WDR | RCSR_HWR)
-	str	r1,	[r0]
-	teq	r1,	#RCSR_SMR
-
-	bne	initirqs
-
-	ldr	r0,	=PSSR
-	mov	r1,	#PSSR_PH
-	str	r1,	[r0]
-
-	/* if so, resume at PSPR */
-	ldr	r0,	=PSPR
-	ldr	r1,	[r0]
-	mov	pc,	r1
-
-	/* ---------------------------------------------------------------- */
-	/* Disable (mask) all interrupts at interrupt controller	    */
-	/* ---------------------------------------------------------------- */
-
-initirqs:
-
-	mov	r1,  #0		/* clear int. level register (IRQ, not FIQ) */
-	ldr	r2,  =ICLR
-	str	r1,  [r2]
-
-	ldr	r2,  =ICMR	/* mask all interrupts at the controller    */
-	str	r1,  [r2]
-
-	/* ---------------------------------------------------------------- */
-	/* Clock initialisation						    */
-	/* ---------------------------------------------------------------- */
-
-initclks:
-
-	/* Disable the peripheral clocks, and set the core clock frequency  */
-
-	/* Turn Off on-chip peripheral clocks (except for memory)	    */
-	/* for re-configuration.					    */
-	ldr	r1,  =CKEN
-	ldr	r2,  =CONFIG_SYS_CKEN
-	str	r2,  [r1]
-
-	/* ... and write the core clock config register			    */
-	ldr	r2,  =CONFIG_SYS_CCCR
-	ldr	r1,  =CCCR
-	str	r2,  [r1]
-
-	/* Turn on turbo mode */
-	mrc	p14, 0, r2, c6, c0, 0
-	orr	r2, r2, #0xB		/* Turbo, Fast-Bus, Freq change**/
-	mcr	p14, 0, r2, c6, c0, 0
-
-	/* Re-write MDREFR */
-	ldr	r1, =MEMC_BASE
-	ldr	r2, [r1, #MDREFR_OFFSET]
-	str	r2, [r1, #MDREFR_OFFSET]
-#ifdef RTC
-	/* enable the 32Khz oscillator for RTC and PowerManager		    */
-	ldr	r1,  =OSCC
-	mov	r2,  #OSCC_OON
-	str	r2,  [r1]
-
-	/* NOTE:  spin here until OSCC.OOK get set, meaning the PLL	    */
-	/* has settled.							    */
-60:
-	ldr	r2, [r1]
-	ands	r2, r2, #1
-	beq	60b
-#else
-#error "RTC not defined"
-#endif
-
-	/* Interrupt init: Mask all interrupts				    */
-    ldr r0, =ICMR /* enable no sources */
-	mov r1, #0
-    str r1, [r0]
-	/* FIXME */
-
-#ifdef NODEBUG
-	/*Disable software and data breakpoints */
-	mov	r0,#0
-	mcr	p15,0,r0,c14,c8,0  /* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0  /* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0  /* dbcon */
-
-	/*Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0  /* dcsr */
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* End lowlevel_init							    */
-	/* ---------------------------------------------------------------- */
-
-endlowlevel_init:
-
-	mov	pc, lr
diff --git a/board/ttcontrol/vision2/vision2.c b/board/ttcontrol/vision2/vision2.c
index ce4cb78..071dad6 100644
--- a/board/ttcontrol/vision2/vision2.c
+++ b/board/ttcontrol/vision2/vision2.c
@@ -37,14 +37,34 @@
 #include <fsl_esdhc.h>
 #include <fsl_pmic.h>
 #include <mc13892.h>
+#include <linux/fb.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
 static u32 system_rev;
 
+extern int mx51_fb_init(struct fb_videomode *mode);
+
 #ifdef CONFIG_HW_WATCHDOG
 #include <watchdog.h>
 
+static struct fb_videomode nec_nl6448bc26_09c = {
+	"NEC_NL6448BC26-09C",
+	60,	/* Refresh */
+	640,	/* xres */
+	480,	/* yres */
+	37650,	/* pixclock = 26.56Mhz */
+	48,	/* left margin */
+	16,	/* right margin */
+	31,	/* upper margin */
+	12,	/* lower margin */
+	96,	/* hsync-len */
+	2,	/* vsync-len */
+	0,	/* sync */
+	FB_VMODE_NONINTERLACED,	/* vmode */
+	0,	/* flag */
+};
+
 void hw_watchdog_reset(void)
 {
 	int val;
@@ -423,6 +443,9 @@ static void setup_gpios(void)
 	mxc_request_iomux(MX51_PIN_CSPI1_RDY, IOMUX_CONFIG_ALT3);
 	mxc_iomux_set_pad(MX51_PIN_CSPI1_RDY, 0x82);
 
+	/* PWM Output GPIO1_2 */
+	mxc_request_iomux(MX51_PIN_GPIO1_2, IOMUX_CONFIG_ALT1);
+
 	/*
 	 * Set GPIO1_4 to high and output; it is used to reset
 	 * the system on reboot
@@ -630,6 +653,33 @@ int board_early_init_f(void)
 	return 0;
 }
 
+static void backlight(int on)
+{
+	if (on) {
+		mxc_gpio_set(65, 1);
+		udelay(10000);
+		mxc_gpio_set(68, 1);
+	} else {
+		mxc_gpio_set(65, 0);
+		mxc_gpio_set(68, 0);
+	}
+}
+
+void lcd_enable(void)
+{
+	int ret;
+
+	mxc_request_iomux(MX51_PIN_DI1_PIN2, IOMUX_CONFIG_ALT0);
+	mxc_request_iomux(MX51_PIN_DI1_PIN3, IOMUX_CONFIG_ALT0);
+
+	mxc_gpio_set(2, 1);
+	mxc_request_iomux(MX51_PIN_GPIO1_2, IOMUX_CONFIG_ALT0);
+
+	ret = mx51_fb_init(&nec_nl6448bc26_09c);
+	if (ret)
+		puts("LCD cannot be configured\n");
+}
+
 int board_init(void)
 {
 #ifdef CONFIG_SYS_ARM_WITHOUT_RELOC
@@ -709,3 +759,21 @@ int checkboard(void)
 	return 0;
 }
 
+int do_vision_lcd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	int on;
+
+	if (argc < 2)
+		return cmd_usage(cmdtp);
+
+	on = (strcmp(argv[1], "on") == 0);
+	backlight(on);
+
+	return 0;
+}
+
+U_BOOT_CMD(
+	lcdbl, CONFIG_SYS_MAXARGS, 1, do_vision_lcd,
+	"Vision2 Backlight",
+	"lcdbl [on|off]\n"
+);
diff --git a/board/wepep250/Makefile b/board/wepep250/Makefile
deleted file mode 100644
index 0669b0e..0000000
--- a/board/wepep250/Makefile
+++ /dev/null
@@ -1,51 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).a
-
-COBJS	:= wepep250.o flash.o
-SOBJS	:= lowlevel_init.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-
-clean:
-	rm -f $(SOBJS) $(OBJS)
-
-distclean:	clean
-	rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/wepep250/config.mk b/board/wepep250/config.mk
deleted file mode 100644
index 60cbc24..0000000
--- a/board/wepep250/config.mk
+++ /dev/null
@@ -1,11 +0,0 @@
-#
-# This is config used for compilation of WEP EP250 sources
-#
-# You might change location of U-Boot in memory by setting right CONFIG_SYS_TEXT_BASE.
-# This allows for example having one copy located at the end of ram and stored
-# in flash device and later on while developing use other location to test
-# the code in RAM device only.
-#
-
-CONFIG_SYS_TEXT_BASE = 0xa1fe0000
-#CONFIG_SYS_TEXT_BASE = 0xa1001000
diff --git a/board/wepep250/flash.c b/board/wepep250/flash.c
deleted file mode 100644
index c6e9171..0000000
--- a/board/wepep250/flash.c
+++ /dev/null
@@ -1,324 +0,0 @@
-/*
- * Copyright (C) 2003 ETC s.r.o.
- *
- * This code was inspired by Marius Groeger and Kyle Harris code
- * available in other board ports for U-Boot
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * Written by Peter Figuli <peposh@etc.sk>, 2003.
- *
- */
-
-#include <common.h>
-#include "intel.h"
-
-
-/*
- * This code should handle CFI FLASH memory device. This code is very
- * minimalistic approach without many essential error handling code as well.
- * Because U-Boot actually is missing smart handling of FLASH device,
- * we just set flash_id to anything else to FLASH_UNKNOW, so common code
- * can call us without any restrictions.
- * TODO: Add CFI Query, to be able to determine FLASH device.
- * TODO: Add error handling code
- * NOTE: This code was tested with BUS_WIDTH 4 and ITERLEAVE 2 only, but
- *       hopefully may work with other configurations.
- */
-
-#if ( WEP_FLASH_BUS_WIDTH == 1 )
-#  define FLASH_BUS vu_char
-#  define FLASH_BUS_RET u_char
-#  if ( WEP_FLASH_INTERLEAVE == 1 )
-#    define FLASH_CMD( x ) x
-#  else
-#    error "With 8bit bus only one chip is allowed"
-#  endif
-
-
-#elif ( WEP_FLASH_BUS_WIDTH == 2 )
-#  define FLASH_BUS vu_short
-#  define FLASH_BUS_RET u_short
-#  if ( WEP_FLASH_INTERLEAVE == 1 )
-#    define FLASH_CMD( x ) x
-#  elif ( WEP_FLASH_INTERLEAVE == 2 )
-#    define FLASH_CMD( x ) (( x << 8 )| x )
-#  else
-#    error "With 16bit bus only 1 or 2 chip(s) are allowed"
-#  endif
-
-
-#elif ( WEP_FLASH_BUS_WIDTH == 4 )
-#  define FLASH_BUS vu_long
-#  define FLASH_BUS_RET u_long
-#  if ( WEP_FLASH_INTERLEAVE == 1 )
-#    define FLASH_CMD( x ) x
-#  elif ( WEP_FLASH_INTERLEAVE == 2 )
-#    define FLASH_CMD( x ) (( x << 16 )| x )
-#  elif ( WEP_FLASH_INTERLEAVE == 4 )
-#    define FLASH_CMD( x ) (( x << 24 )|( x << 16 ) ( x << 8 )| x )
-#  else
-#    error "With 32bit bus only 1,2 or 4 chip(s) are allowed"
-#  endif
-
-#else
-#  error "Flash bus width might be 1,2,4 for 8,16,32 bit configuration"
-#endif
-
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-static FLASH_BUS_RET flash_status_reg (void)
-{
-
-	FLASH_BUS *addr = (FLASH_BUS *) 0;
-
-	*addr = FLASH_CMD (CFI_INTEL_CMD_READ_STATUS_REGISTER);
-
-	return *addr;
-}
-
-static int flash_ready (ulong timeout)
-{
-	int ok = 1;
-
-	reset_timer_masked ();
-	while ((flash_status_reg () & FLASH_CMD (CFI_INTEL_SR_READY)) !=
-		   FLASH_CMD (CFI_INTEL_SR_READY)) {
-		if (get_timer_masked () > timeout && timeout != 0) {
-			ok = 0;
-			break;
-		}
-	}
-	return ok;
-}
-
-#if ( CONFIG_SYS_MAX_FLASH_BANKS != 1 )
-#  error "WEP platform has only one flash bank!"
-#endif
-
-
-ulong flash_init (void)
-{
-	int i;
-	FLASH_BUS address = WEP_FLASH_BASE;
-
-	flash_info[0].size = WEP_FLASH_BANK_SIZE;
-	flash_info[0].sector_count = CONFIG_SYS_MAX_FLASH_SECT;
-	flash_info[0].flash_id = INTEL_MANUFACT;
-	memset (flash_info[0].protect, 0, CONFIG_SYS_MAX_FLASH_SECT);
-
-	for (i = 0; i < CONFIG_SYS_MAX_FLASH_SECT; i++) {
-		flash_info[0].start[i] = address;
-#ifdef WEP_FLASH_UNLOCK
-		/* Some devices are hw locked after start. */
-		*((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_LOCK_SETUP);
-		*((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_UNLOCK_BLOCK);
-		flash_ready (0);
-		*((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY);
-#endif
-		address += WEP_FLASH_SECT_SIZE;
-	}
-
-	flash_protect (FLAG_PROTECT_SET,
-				   CONFIG_SYS_FLASH_BASE,
-				   CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1,
-				   &flash_info[0]);
-
-	flash_protect (FLAG_PROTECT_SET,
-				   CONFIG_ENV_ADDR,
-				   CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-
-	return WEP_FLASH_BANK_SIZE;
-}
-
-void flash_print_info (flash_info_t * info)
-{
-	int i;
-
-	printf (" Intel vendor\n");
-	printf ("  Size: %ld MB in %d Sectors\n",
-			info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i = 0; i < info->sector_count; i++) {
-		if (!(i % 5)) {
-			printf ("\n");
-		}
-
-		printf (" %08lX%s", info->start[i],
-				info->protect[i] ? " (RO)" : "     ");
-	}
-	printf ("\n");
-}
-
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
-	int flag, non_protected = 0, sector;
-	int rc = ERR_OK;
-
-	FLASH_BUS *address;
-
-	for (sector = s_first; sector <= s_last; sector++) {
-		if (!info->protect[sector]) {
-			non_protected++;
-		}
-	}
-
-	if (!non_protected) {
-		return ERR_PROTECTED;
-	}
-
-	/*
-	 * Disable interrupts which might cause a timeout
-	 * here. Remember that our exception vectors are
-	 * at address 0 in the flash, and we don't want a
-	 * (ticker) exception to happen while the flash
-	 * chip is in programming mode.
-	 */
-	flag = disable_interrupts ();
-
-
-	/* Start erase on unprotected sectors */
-	for (sector = s_first; sector <= s_last && !ctrlc (); sector++) {
-		if (info->protect[sector]) {
-			printf ("Protected sector %2d skipping...\n", sector);
-			continue;
-		} else {
-			printf ("Erasing sector %2d ... ", sector);
-		}
-
-		address = (FLASH_BUS *) (info->start[sector]);
-
-		*address = FLASH_CMD (CFI_INTEL_CMD_BLOCK_ERASE);
-		*address = FLASH_CMD (CFI_INTEL_CMD_CONFIRM);
-		if (flash_ready (CONFIG_SYS_FLASH_ERASE_TOUT)) {
-			*address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER);
-			printf ("ok.\n");
-		} else {
-			*address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND);
-			rc = ERR_TIMOUT;
-			printf ("timeout! Aborting...\n");
-			break;
-		}
-		*address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY);
-	}
-	if (ctrlc ())
-		printf ("User Interrupt!\n");
-
-	/* allow flash to settle - wait 10 ms */
-	udelay_masked (10000);
-	if (flag) {
-		enable_interrupts ();
-	}
-
-	return rc;
-}
-
-static int write_data (flash_info_t * info, ulong dest, FLASH_BUS data)
-{
-	FLASH_BUS *address = (FLASH_BUS *) dest;
-	int rc = ERR_OK;
-	int flag;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*address & data) != data) {
-		return ERR_NOT_ERASED;
-	}
-
-	/*
-	 * Disable interrupts which might cause a timeout
-	 * here. Remember that our exception vectors are
-	 * at address 0 in the flash, and we don't want a
-	 * (ticker) exception to happen while the flash
-	 * chip is in programming mode.
-	 */
-
-	flag = disable_interrupts ();
-
-	*address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER);
-	*address = FLASH_CMD (CFI_INTEL_CMD_PROGRAM1);
-	*address = data;
-
-	if (!flash_ready (CONFIG_SYS_FLASH_WRITE_TOUT)) {
-		*address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND);
-		rc = ERR_TIMOUT;
-		printf ("timeout! Aborting...\n");
-	}
-
-	*address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY);
-	if (flag) {
-		enable_interrupts ();
-	}
-
-	return rc;
-}
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
-	ulong read_addr, write_addr;
-	FLASH_BUS data;
-	int i, result = ERR_OK;
-
-
-	read_addr = addr & ~(sizeof (FLASH_BUS) - 1);
-	write_addr = read_addr;
-	if (read_addr != addr) {
-		data = 0;
-		for (i = 0; i < sizeof (FLASH_BUS); i++) {
-			if (read_addr < addr || cnt == 0) {
-				data |= *((uchar *) read_addr) << i * 8;
-			} else {
-				data |= (*src++) << i * 8;
-				cnt--;
-			}
-			read_addr++;
-		}
-		if ((result = write_data (info, write_addr, data)) != ERR_OK) {
-			return result;
-		}
-		write_addr += sizeof (FLASH_BUS);
-	}
-	for (; cnt >= sizeof (FLASH_BUS); cnt -= sizeof (FLASH_BUS)) {
-		if ((result = write_data (info, write_addr,
-								  *((FLASH_BUS *) src))) != ERR_OK) {
-			return result;
-		}
-		write_addr += sizeof (FLASH_BUS);
-		src += sizeof (FLASH_BUS);
-	}
-	if (cnt > 0) {
-		read_addr = write_addr;
-		data = 0;
-		for (i = 0; i < sizeof (FLASH_BUS); i++) {
-			if (cnt > 0) {
-				data |= (*src++) << i * 8;
-				cnt--;
-			} else {
-				data |= *((uchar *) read_addr) << i * 8;
-			}
-			read_addr++;
-		}
-		if ((result = write_data (info, write_addr, data)) != 0) {
-			return result;
-		}
-	}
-	return ERR_OK;
-}
diff --git a/board/wepep250/intel.h b/board/wepep250/intel.h
deleted file mode 100644
index 77498b6..0000000
--- a/board/wepep250/intel.h
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * Copyright (C) 2002 ETC s.r.o.
- * All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- * 1. Redistributions of source code must retain the above copyright
- *    notice, this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright
- *    notice, this list of conditions and the following disclaimer in the
- *    documentation and/or other materials provided with the distribution.
- * 3. Neither the name of the ETC s.r.o. nor the names of its contributors
- *    may be used to endorse or promote products derived from this software
- *    without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
- * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * Written by Marcel Telka <marcel@telka.sk>, 2002.
- *
- * Documentation:
- * [1] Intel Corporation, "3 Volt Intel Strata Flash Memory 28F128J3A, 28F640J3A,
- *     28F320J3A (x8/x16)", April 2002, Order Number: 290667-011
- * [2] Intel Corporation, "3 Volt Synchronous Intel Strata Flash Memory 28F640K3, 28F640K18,
- *     28F128K3, 28F128K18, 28F256K3, 28F256K18 (x16)", June 2002, Order Number: 290737-005
- *
- * This file is taken from OpenWinCE project hosted by SourceForge.net
- *
- */
-
-#ifndef	FLASH_INTEL_H
-#define	FLASH_INTEL_H
-
-#include <common.h>
-
-/* Intel CFI commands - see Table 4. in [1] and Table 3. in [2] */
-
-#define	CFI_INTEL_CMD_READ_ARRAY		0xFF	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_READ_IDENTIFIER		0x90	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_READ_QUERY		0x98	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_READ_STATUS_REGISTER	0x70	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_CLEAR_STATUS_REGISTER	0x50	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_PROGRAM1			0x40	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_PROGRAM2			0x10	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_WRITE_TO_BUFFER		0xE8	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_CONFIRM			0xD0	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_BLOCK_ERASE		0x20	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_SUSPEND			0xB0	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_RESUME			0xD0	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_LOCK_SETUP		0x60	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_LOCK_BLOCK		0x01	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_UNLOCK_BLOCK		0xD0	/* 28FxxxJ3A - unlocks all blocks, 28FFxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_CMD_LOCK_DOWN_BLOCK		0x2F	/* 28FxxxK3, 28FxxxK18 */
-
-/* Intel CFI Status Register bits - see Table 6. in [1] and Table 7. in [2] */
-
-#define	CFI_INTEL_SR_READY			1 << 7	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_SR_ERASE_SUSPEND		1 << 6	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_SR_ERASE_ERROR		1 << 5	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_SR_PROGRAM_ERROR		1 << 4	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_SR_VPEN_ERROR			1 << 3	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_SR_PROGRAM_SUSPEND		1 << 2	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_SR_BLOCK_LOCKED		1 << 1	/* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
-#define	CFI_INTEL_SR_BEFP			1 << 0	/* 28FxxxK3, 28FxxxK18 */
-
-/* Intel flash device ID codes for 28FxxxJ3A - see Table 5. in [1] */
-
-#define	CFI_CHIP_INTEL_28F320J3A		0x0016
-#define	CFI_CHIPN_INTEL_28F320J3A		"28F320J3A"
-#define	CFI_CHIP_INTEL_28F640J3A		0x0017
-#define	CFI_CHIPN_INTEL_28F640J3A		"28F640J3A"
-#define	CFI_CHIP_INTEL_28F128J3A		0x0018
-#define	CFI_CHIPN_INTEL_28F128J3A		"28F128J3A"
-
-/* Intel flash device ID codes for 28FxxxK3 and 28FxxxK18 - see Table 8. in [2] */
-
-#define	CFI_CHIP_INTEL_28F640K3			0x8801
-#define	CFI_CHIPN_INTEL_28F640K3		"28F640K3"
-#define	CFI_CHIP_INTEL_28F128K3			0x8802
-#define	CFI_CHIPN_INTEL_28F128K3		"28F128K3"
-#define	CFI_CHIP_INTEL_28F256K3			0x8803
-#define	CFI_CHIPN_INTEL_28F256K3		"28F256K3"
-#define	CFI_CHIP_INTEL_28F640K18		0x8805
-#define	CFI_CHIPN_INTEL_28F640K18		"28F640K18"
-#define	CFI_CHIP_INTEL_28F128K18		0x8806
-#define	CFI_CHIPN_INTEL_28F128K18		"28F128K18"
-#define	CFI_CHIP_INTEL_28F256K18		0x8807
-#define	CFI_CHIPN_INTEL_28F256K18		"28F256K18"
-
-#endif /* FLASH_INTEL_H */
diff --git a/board/wepep250/lowlevel_init.S b/board/wepep250/lowlevel_init.S
deleted file mode 100644
index 9bb091f..0000000
--- a/board/wepep250/lowlevel_init.S
+++ /dev/null
@@ -1,145 +0,0 @@
-/*
- * Copyright (C) 2001, 2002 ETC s.r.o.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA
- * 02111-1307, USA.
- *
- * Written by Marcel Telka <marcel@telka.sk>, 2001, 2002.
- * Changes for U-Boot Peter Figuli <peposh@etc.sk>, 2003.
- *
- * This file is taken from OpenWinCE project hosted by SourceForge.net
- *
- * Documentation:
- * [1] Intel Corporation, "Intel PXA250 and PXA210 Application Processors
- *     Developer's Manual", February 2002, Order Number: 278522-001
- * [2] Samsung Electronics, "8Mx16 SDRAM 54CSP K4S281633D-RL/N/P",
- *     Revision 1.0, February 2002
- * [3] Samsung Electronics, "16Mx16 SDRAM 54CSP K4S561633C-RL(N)",
- *     Revision 1.0, February 2002
- *
-*/
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-.globl lowlevel_init
-lowlevel_init:
-
-	mov	r10, lr
-
-/*	setup memory - see 6.12 in [1]
- *	Step 1	- wait 200 us
- */
-	mov	r0,#0x2700			/* wait 200 us @ 99.5 MHz */
-1:	subs	r0, r0, #1
-	bne	1b
-/*	TODO: complete step 1 for Synchronous Static memory*/
-
-	ldr	r0, =0x48000000			/* MC_BASE */
-
-
-/*	step 1.a - setup MSCx
- */
-	ldr	r1, =0x000012B3			/* MSC0_RRR0(1) | MSC0_RDN0(2) | MSC0_RDF0(11) | MSC0_RT0(3) */
-	str	r1, [r0, #0x8]			/* MSC0_OFFSET */
-
-/*	step 1.c - clear MDREFR:K1FREE, set MDREFR:DRI
- *	see AUTO REFRESH chapter in section D. in [2] and in [3]
- *	DRI = (64ms / 4096) * 99.53MHz / 32 = 48 for K4S281633
- *	DRI = (64ms / 8192) * 99.52MHz / 32 = 24 for K4S561633
- *	TODO: complete for Synchronous Static memory
- */
-	ldr	r1, [r0, #4]			/* MDREFR_OFFSET */
-	ldr	r2, =0x01000FFF			/* MDREFR_K1FREE | MDREFR_DRI_MASK */
-	bic	r1, r1, r2
-#if defined( WEP_SDRAM_K4S281633 )
-	orr	r1, r1, #48			/* MDREFR_DRI(48) */
-#elif defined( WEP_SDRAM_K4S561633 )
-	orr	r1, r1, #24			/* MDREFR_DRI(24) */
-#else
-#error SDRAM chip is not defined
-#endif
-
-	str	r1, [r0, #4]			/* MDREFR_OFFSET */
-
-/*	Step 2 - only for Synchronous Static memory (TODO)
- *
- *	Step 3 - same as step 4
- *
- *	Step 4
- *
- *	Step 4.a - set MDREFR:K1RUN, clear MDREFR:K1DB2
- */
-	orr	r1, r1, #0x00010000		/* MDREFR_K1RUN */
-	bic	r1, r1, #0x00020000		/* MDREFR_K1DB2 */
-	str	r1, [r0, #4]			/* MDREFR_OFFSET */
-
-/*	Step 4.b - clear MDREFR:SLFRSH */
-	bic	r1, r1, #0x00400000		/* MDREFR_SLFRSH */
-	str	r1, [r0, #4]			/* MDREFR_OFFSET */
-
-/*	Step 4.c - set MDREFR:E1PIN */
-	orr	r1, r1, #0x00008000		/* MDREFR_E1PIN */
-	str	r1, [r0, #4]			/* MDREFR_OFFSET */
-
-/*	Step 4.d - automatically done
- *
- *	Steps 4.e and 4.f - configure SDRAM
- */
-#if defined( WEP_SDRAM_K4S281633 )
-	ldr	r1, =0x00000AA8			/* MDCNFG_DTC0(2) | MDCNFG_DLATCH0 | MDCNFG_DCAC0(1) | MDCNFG_DRAC0(1) | MDCNFG_DNB0 */
-#elif defined( WEP_SDRAM_K4S561633 )
-	ldr	r1, =0x00000AC8			/* MDCNFG_DTC0(2) | MDCNFG_DLATCH0 | MDCNFG_DCAC0(1) | MDCNFG_DRAC0(2) | MDCNFG_DNB0 */
-#else
-#error SDRAM chip is not defined
-#endif
-	str	r1, [r0, #0]			/* MDCNFG_OFFSET */
-
-/*	Step 5 - wait at least 200 us for SDRAM
- *	see section B. in [2]
- */
-	mov	r2,#0x2700			/* wait 200 us @ 99.5 MHz */
-1:	subs	r2, r2, #1
-	bne	1b
-
-/*	Step 6 - after reset dcache is disabled, so automatically done
- *
- *	Step 7 - eight refresh cycles
- */
-	mov	r2, #0xA0000000
-	ldr	r3, [r2]
-	ldr	r3, [r2]
-	ldr	r3, [r2]
-	ldr	r3, [r2]
-	ldr	r3, [r2]
-	ldr	r3, [r2]
-	ldr	r3, [r2]
-	ldr	r3, [r2]
-
-/*	Step 8 - we don't need dcache now
- *
- *	Step 9 - enable SDRAM partition 0
- */
-	orr	r1, r1, #1			/* MDCNFG_DE0 */
-	str	r1, [r0, #0]			/* MDCNFG_OFFSET */
-
-/*	Step 10 - write MDMRS */
-	mov	r1, #0
-	str	r1, [r0, #0x40]			/* MDMRS_OFFSET */
-
-/*	Step 11 - optional (TODO) */
-
-	mov	pc,r10
diff --git a/board/wepep250/wepep250.c b/board/wepep250/wepep250.c
deleted file mode 100644
index 6e41ea6..0000000
--- a/board/wepep250/wepep250.c
+++ /dev/null
@@ -1,68 +0,0 @@
-/*
- * Copyright (C) 2003 ETC s.r.o.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * Written by Peter Figuli <peposh@etc.sk>, 2003.
- *
- */
-
-#include <common.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/io.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init (void)
-{
-	gd->bd->bi_arch_number = MACH_TYPE_WEP_EP250;
-	gd->bd->bi_boot_params = 0xa0000000;
-/*
- * Setup GPIO stuff to get serial working
- */
-#if defined( CONFIG_FFUART )
-	writel(0x80, GPDR1);
-	writel(0x8010, GAFR1_L);
-#elif defined( CONFIG_BTUART )
-	writel(0x800, GPDR1);
-	writel(0x900000, GAFR1_L);
-#endif
-	writel(0x20, PSSR);
-
-	return 0;
-}
-
-int dram_init (void)
-{
-#if ( CONFIG_NR_DRAM_BANKS > 0 )
-	gd->bd->bi_dram[0].start = WEP_SDRAM_1;
-	gd->bd->bi_dram[0].size = WEP_SDRAM_1_SIZE;
-#endif
-#if ( CONFIG_NR_DRAM_BANKS > 1 )
-	gd->bd->bi_dram[1].start = WEP_SDRAM_2;
-	gd->bd->bi_dram[1].size = WEP_SDRAM_2_SIZE;
-#endif
-#if ( CONFIG_NR_DRAM_BANKS > 2 )
-	gd->bd->bi_dram[2].start = WEP_SDRAM_3;
-	gd->bd->bi_dram[2].size = WEP_SDRAM_3_SIZE;
-#endif
-#if ( CONFIG_NR_DRAM_BANKS > 3 )
-	gd->bd->bi_dram[3].start = WEP_SDRAM_4;
-	gd->bd->bi_dram[3].size = WEP_SDRAM_4_SIZE;
-#endif
-
-	return 0;
-}
diff --git a/board/xaeniax/Makefile b/board/xaeniax/Makefile
index 7dd2ea0..554915a 100644
--- a/board/xaeniax/Makefile
+++ b/board/xaeniax/Makefile
@@ -26,17 +26,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= xaeniax.o flash.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/xaeniax/config.mk b/board/xaeniax/config.mk
deleted file mode 100644
index c639752..0000000
--- a/board/xaeniax/config.mk
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0xa3FB0000
-#CONFIG_SYS_TEXT_BASE = 0
diff --git a/board/xaeniax/lowlevel_init.S b/board/xaeniax/lowlevel_init.S
deleted file mode 100644
index 57e1620..0000000
--- a/board/xaeniax/lowlevel_init.S
+++ /dev/null
@@ -1,424 +0,0 @@
- /*
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * NOTE: I haven't clean this up considerably, just enough to get it
- * running. See hal_platform_setup.h for the source. See
- * board/cradle/lowlevel_init.S for another PXA250 setup that is
- * much cleaner.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-/* wait for coprocessor write complete */
-	.macro CPWAIT reg
-	mrc  p15,0,\reg,c2,c0,0
-	mov  \reg,\reg
-	sub  pc,pc,#4
-	.endm
-
-
-.globl lowlevel_init
-lowlevel_init:
-
-	mov	 r10, lr
-
-	/* Set up GPIO pins first ----------------------------------------- */
-
-	ldr	r0,=GPSR0
-	ldr	r1,=CONFIG_SYS_GPSR0_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GPSR1
-	ldr	r1,=CONFIG_SYS_GPSR1_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GPSR2
-	ldr	r1,=CONFIG_SYS_GPSR2_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GPCR0
-	ldr	r1,=CONFIG_SYS_GPCR0_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GPCR1
-	ldr	r1,=CONFIG_SYS_GPCR1_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GPCR2
-	ldr	r1,=CONFIG_SYS_GPCR2_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GPDR0
-	ldr	r1,=CONFIG_SYS_GPDR0_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GPDR1
-	ldr	r1,=CONFIG_SYS_GPDR1_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GPDR2
-	ldr	r1,=CONFIG_SYS_GPDR2_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GAFR0_L
-	ldr	r1,=CONFIG_SYS_GAFR0_L_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GAFR0_U
-	ldr	r1,=CONFIG_SYS_GAFR0_U_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GAFR1_L
-	ldr	r1,=CONFIG_SYS_GAFR1_L_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GAFR1_U
-	ldr	r1,=CONFIG_SYS_GAFR1_U_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GAFR2_L
-	ldr	r1,=CONFIG_SYS_GAFR2_L_VAL
-	str	r1,[r0]
-
-	ldr	r0,=GAFR2_U
-	ldr	r1,=CONFIG_SYS_GAFR2_U_VAL
-	str	r1,[r0]
-
-	ldr	r0,=PSSR		/* enable GPIO pins */
-	ldr	r1,=CONFIG_SYS_PSSR_VAL
-	str	r1,[r0]
-
-	/* ---------------------------------------------------------------- */
-	/* Enable memory interface                                          */
-	/*                                                                  */
-	/* The sequence below is based on the recommended init steps        */
-	/* detailed in the Intel PXA250 Operating Systems Developers Guide, */
-	/* Chapter 10.                                                      */
-	/* ---------------------------------------------------------------- */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 1: Wait for at least 200 microsedonds to allow internal     */
-	/*         clocks to settle. Only necessary after hard reset...     */
-	/*         FIXME: can be optimized later                            */
-	/* ---------------------------------------------------------------- */
-
-	ldr	r3, =OSCR		/* reset the OS Timer Count to zero */
-	mov	r2, #0
-	str	r2, [r3]
-	ldr	r4, =0x300		/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	ldr	r2, [r3]
-	cmp	r4, r2
-	bgt	1b
-
-mem_init:
-
-	ldr	r1,=MEMC_BASE		/* get memory controller base addr. */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2a: Initialize Asynchronous static memory controller        */
-	/* ---------------------------------------------------------------- */
-
-	/* MSC registers: timing, bus width, mem type                       */
-
-	/* MSC0: nCS(0,1)                                                   */
-	ldr     r2,=CONFIG_SYS_MSC0_VAL
-	str     r2,[r1, #MSC0_OFFSET]
-	ldr     r2,[r1, #MSC0_OFFSET]	/* read back to ensure data latches */
-
-	/* MSC1: nCS(2,3)                                                   */
-	ldr     r2,=CONFIG_SYS_MSC1_VAL
-	str     r2,[r1, #MSC1_OFFSET]
-	ldr     r2,[r1, #MSC1_OFFSET]
-
-	/* MSC2: nCS(4,5)                                                   */
-	ldr     r2,=CONFIG_SYS_MSC2_VAL
-	str     r2,[r1, #MSC2_OFFSET]
-	ldr     r2,[r1, #MSC2_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2b: Initialize Card Interface                               */
-	/* ---------------------------------------------------------------- */
-
-	/* MECR: Memory Expansion Card Register                             */
-	ldr     r2,=CONFIG_SYS_MECR_VAL
-	str     r2,[r1, #MECR_OFFSET]
-	ldr	r2,[r1, #MECR_OFFSET]
-
-	/* MCMEM0: Card Interface slot 0 timing                             */
-	ldr     r2,=CONFIG_SYS_MCMEM0_VAL
-	str     r2,[r1, #MCMEM0_OFFSET]
-	ldr	r2,[r1, #MCMEM0_OFFSET]
-
-	/* MCMEM1: Card Interface slot 1 timing                             */
-	ldr     r2,=CONFIG_SYS_MCMEM1_VAL
-	str     r2,[r1, #MCMEM1_OFFSET]
-	ldr	r2,[r1, #MCMEM1_OFFSET]
-
-	/* MCATT0: Card Interface Attribute Space Timing, slot 0            */
-	ldr     r2,=CONFIG_SYS_MCATT0_VAL
-	str     r2,[r1, #MCATT0_OFFSET]
-	ldr	r2,[r1, #MCATT0_OFFSET]
-
-	/* MCATT1: Card Interface Attribute Space Timing, slot 1            */
-	ldr     r2,=CONFIG_SYS_MCATT1_VAL
-	str     r2,[r1, #MCATT1_OFFSET]
-	ldr	r2,[r1, #MCATT1_OFFSET]
-
-	/* MCIO0: Card Interface I/O Space Timing, slot 0                   */
-	ldr     r2,=CONFIG_SYS_MCIO0_VAL
-	str     r2,[r1, #MCIO0_OFFSET]
-	ldr	r2,[r1, #MCIO0_OFFSET]
-
-	/* MCIO1: Card Interface I/O Space Timing, slot 1                   */
-	ldr     r2,=CONFIG_SYS_MCIO1_VAL
-	str     r2,[r1, #MCIO1_OFFSET]
-	ldr	r2,[r1, #MCIO1_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2c: Write FLYCNFG  FIXME: what's that???                    */
-	/* ---------------------------------------------------------------- */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 2d: Initialize Timing for Sync Memory (SDCLK0)              */
-	/* ---------------------------------------------------------------- */
-
-	@ get the mdrefr settings
-	ldr     r4,=CONFIG_SYS_MDREFR_VAL
-
-	@ write back mdrefr
-	str     r4,[r1, #MDREFR_OFFSET]
-	ldr     r4,[r1, #MDREFR_OFFSET]
-
-	/* ---------------------------------------------------------------- */
-	/* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */
-	/* ---------------------------------------------------------------- */
-
-	/* Initialize SXCNFG register. Assert the enable bits               */
-
-	/* Write SXMRS to cause an MRS command to all enabled banks of      */
-	/* synchronous static memory. Note that SXLCR need not be written   */
-	/* at this time.                                                    */
-
-	/* FIXME: we use async mode for now                                 */
-
-	/* ---------------------------------------------------------------- */
-	/* Step 4: Initialize SDRAM                                         */
-	/* ---------------------------------------------------------------- */
-
-	@ set K1RUN for bank 0
-	@
-	orr   r4,  r4,  #MDREFR_K1RUN
-
-	@ write back mdrefr
-	@
-	str     r4,  [r1, #MDREFR_OFFSET]
-	ldr     r4,  [r1, #MDREFR_OFFSET]
-
-	@ deassert SLFRSH
-	@
-	bic     r4,  r4,  #MDREFR_SLFRSH
-
-	@ write back mdrefr
-	@
-	str     r4,  [r1, #MDREFR_OFFSET]
-	ldr     r4,  [r1, #MDREFR_OFFSET]
-
-	@ assert E1PIN
-	@ if E0PIN is also used:	 #(MDREFR_E1PIN|MDREFR_E0PIN)
-	orr     r4,  r4, #(MDREFR_E1PIN)
-
-	@ write back mdrefr
-	@
-	str     r4,  [r1, #MDREFR_OFFSET]
-	ldr     r4,  [r1, #MDREFR_OFFSET]
-	nop
-	nop
-
-	/* Step 4d:							*/
-	/* fetch platform value of mdcnfg				*/
-	@
-	ldr     r2,  =CONFIG_SYS_MDCNFG_VAL
-
-	@ disable all sdram banks
-	@
-	bic     r2,  r2,  #(MDCNFG_DE0 | MDCNFG_DE1)
-	bic     r2,  r2,  #(MDCNFG_DE2 | MDCNFG_DE3)
-
-	@ program banks 0/1 for bus width
-	@
-	bic   r2,  r2,  #MDCNFG_DWID0      @0=32-bit
-
-	@ write initial value of mdcnfg, w/o enabling sdram banks
-	@
-	str     r2,  [r1, #MDCNFG_OFFSET]
-
-	/* Step 4e: Wait for the clock to the SDRAMs to stabilize,          */
-	/*          100..200 µsec.                                          */
-
-	ldr	r3, =OSCR		/* reset the OS Timer Count to zero */
-	mov	r2, #0
-	str	r2, [r3]
-	ldr	r4, =0x300		/* really 0x2E1 is about 200usec,   */
-					/* so 0x300 should be plenty        */
-1:
-	ldr	r2, [r3]
-	cmp	r4, r2
-	bgt	1b
-
-
-	/* Step 4f: Trigger a number (usually 8) refresh cycles by          */
-	/*          attempting non-burst read or write accesses to disabled */
-	/*          SDRAM, as commonly specified in the power up sequence   */
-	/*          documented in SDRAM data sheets. The address(es) used   */
-	/*          for this purpose must not be cacheable.                 */
-
-	ldr	r3,	=CONFIG_SYS_DRAM_BASE
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-	str	r2,	[r3]
-
-
-	/* Step 4g: Write MDCNFG with enable bits asserted                  */
-	/* get memory controller base address                               */
-	ldr     r1,  =MEMC_BASE
-
-	@fetch current mdcnfg value
-	@
-	ldr     r3,  [r1, #MDCNFG_OFFSET]
-
-	@enable sdram bank 0 if installed (must do for any populated bank)
-	@
-	orr     r3,  r3,  #MDCNFG_DE0
-
-	@write back mdcnfg, enabling the sdram bank(s)
-	@
-	str     r3,  [r1, #MDCNFG_OFFSET]
-
-	/* Step 4h: Write MDMRS.                                            */
-
-	ldr     r2,	=CONFIG_SYS_MDMRS_VAL
-	str     r2,	[r1, #MDMRS_OFFSET]
-
-
-	/* We are finished with Intel's memory controller initialisation    */
-
-
-	/* ---------------------------------------------------------------- */
-	/* Disable (mask) all interrupts at interrupt controller            */
-	/* ---------------------------------------------------------------- */
-
-initirqs:
-	mov     r1, #0		/* clear int. level register (IRQ, not FIQ) */
-	ldr     r2,  =ICLR
-	str     r1,  [r2]
-
-	ldr     r1,  =CONFIG_SYS_ICMR_VAL /* mask all interrupts at the controller */
-	ldr     r2,  =ICMR
-	str     r1,  [r2]
-
-
-	/* ---------------------------------------------------------------- */
-	/* Clock initialisation                                             */
-	/* ---------------------------------------------------------------- */
-
-initclks:
-
-	/* Disable the peripheral clocks, and set the core clock frequency  */
-	/* (hard-coding at 398.12MHz for now).                              */
-	/* Turn Off ALL on-chip peripheral clocks for re-configuration      */
-	/* Note: See label 'ENABLECLKS' for the re-enabling                 */
-	ldr     r1,  =CKEN
-	mov     r2,  #0
-	str     r2,  [r1]
-
-
-	/* default value						    */
-	ldr     r2, =(CCCR_L27|CCCR_M2|CCCR_N10)  /* DEFAULT: {200/200/100} */
-
-	/* ... and write the core clock config register                     */
-	ldr     r1,  =CCCR
-	str     r2,  [r1]
-
-#ifdef RTC
-	/* enable the 32Khz oscillator for RTC and PowerManager             */
-
-	ldr     r1,  =OSCC
-	mov     r2,  #OSCC_OON
-	str     r2,  [r1]
-
-	/* NOTE:  spin here until OSCC.OOK get set, meaning the PLL         */
-	/* has settled.                                                     */
-60:
-	ldr     r2, [r1]
-	ands    r2, r2, #1
-	beq     60b
-#endif
-
-	@ Turn on needed clocks
-	@
-test:
-	ldr     r1,  =CKEN
-	ldr     r2,  =CONFIG_SYS_CKEN_VAL
-	str     r2,  [r1]
-
-	/* ---------------------------------------------------------------- */
-	/*                                                                  */
-	/* ---------------------------------------------------------------- */
-
-	/* Save SDRAM size ?*/
-	ldr	r1, =DRAM_SIZE
-	str	r8, [r1]
-
-	/* FIXME */
-
-#define NODEBUG
-#ifdef NODEBUG
-	/*Disable software and data breakpoints */
-	mov	r0,#0
-	mcr	p15,0,r0,c14,c8,0  /* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0  /* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0  /* dbcon */
-
-	/*Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0  /* dcsr */
-
-#endif
-
-	/* ---------------------------------------------------------------- */
-	/* End lowlevel_init                                                     */
-	/* ---------------------------------------------------------------- */
-
-endlowlevel_init:
-
-	mov     pc, lr
diff --git a/board/xaeniax/xaeniax.c b/board/xaeniax/xaeniax.c
index 4c19c4d..40b0f3b 100644
--- a/board/xaeniax/xaeniax.c
+++ b/board/xaeniax/xaeniax.c
@@ -39,8 +39,9 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int board_init (void)
 {
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
 
 	/* arch number of xaeniax */
 	gd->bd->bi_arch_number = 585;
@@ -58,19 +59,18 @@ int board_late_init(void)
 	return 0;
 }
 
+extern void pxa_dram_init(void);
+int dram_init(void)
+{
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
 
-int dram_init (void)
+void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-	/*	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;*/
-	/*	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;*/
-	/*	gd->bd->bi_dram[2].start = PHYS_SDRAM_3; */
-	/*	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE; */
-	/*	gd->bd->bi_dram[3].start = PHYS_SDRAM_4; */
-	/*	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE; */
-
-	return 0;
 }
 
 #ifdef CONFIG_CMD_NET
diff --git a/board/xes/common/Makefile b/board/xes/common/Makefile
index d022831..16e0b66 100644
--- a/board/xes/common/Makefile
+++ b/board/xes/common/Makefile
@@ -32,7 +32,11 @@ LIB	= $(obj)lib$(VENDOR).a
 COBJS-$(CONFIG_FSL_PCI_INIT)	+= fsl_8xxx_pci.o
 COBJS-$(CONFIG_MPC8572)		+= fsl_8xxx_clk.o
 COBJS-$(CONFIG_MPC86xx)		+= fsl_8xxx_clk.o
+COBJS-$(CONFIG_P2020)		+= fsl_8xxx_clk.o
 COBJS-$(CONFIG_FSL_DDR2)	+= fsl_8xxx_ddr.o
+COBJS-$(CONFIG_FSL_DDR3)	+= fsl_8xxx_ddr.o
+COBJS-$(CONFIG_MPC85xx)		+= fsl_8xxx_misc.o board.o
+COBJS-$(CONFIG_MPC86xx)		+= fsl_8xxx_misc.o board.o
 COBJS-$(CONFIG_NAND_ACTL)	+= actl_nand.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
diff --git a/board/xes/common/board.c b/board/xes/common/board.c
new file mode 100644
index 0000000..738f0a6
--- /dev/null
+++ b/board/xes/common/board.c
@@ -0,0 +1,64 @@
+/*
+ * Copyright 2009 Extreme Engineering Solutions, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <common.h>
+#include "fsl_8xxx_misc.h"
+
+int checkboard(void)
+{
+	char name[] = CONFIG_SYS_BOARD_NAME;
+	char *s;
+
+#ifdef CONFIG_SYS_FORM_CUSTOM
+	s = "Custom";
+#elif CONFIG_SYS_FORM_6U_CPCI
+	s = "6U CompactPCI";
+#elif CONFIG_SYS_FORM_ATCA_PMC
+	s = "ATCA w/PMC";
+#elif CONFIG_SYS_FORM_ATCA_AMC
+	s = "ATCA w/AMC";
+#elif CONFIG_SYS_FORM_VME
+	s = "VME";
+#elif CONFIG_SYS_FORM_6U_VPX
+	s = "6U VPX";
+#elif CONFIG_SYS_FORM_PMC
+	s = "PMC";
+#elif CONFIG_SYS_FORM_PCI
+	s = "PCI";
+#elif CONFIG_SYS_FORM_3U_CPCI
+	s = "3U CompactPCI";
+#elif CONFIG_SYS_FORM_AMC
+	s = "AdvancedMC";
+#elif CONFIG_SYS_FORM_XMC
+	s = "XMC";
+#elif CONFIG_SYS_FORM_PMC_XMC
+	s = "PMC/XMC";
+#elif CONFIG_SYS_FORM_PCI_EXPRESS
+	s = "PCI Express";
+#elif CONFIG_SYS_FORM_3U_VPX
+	s = "3U VPX";
+#else
+#error "Form factor not defined"
+#endif
+
+	name[strlen(name) - 1] += get_board_derivative();
+	printf("Board: X-ES %s %s SBC\n", name, s);
+
+	/* Display board specific information */
+	puts("       ");
+	if ((s = getenv("board_rev")))
+		printf("Rev %s, ", s);
+	if ((s = getenv("serial#")))
+		printf("Serial# %s, ", s);
+	if ((s = getenv("board_cfg")))
+		printf("Cfg %s", s);
+	puts("\n");
+
+	return 0;
+}
diff --git a/board/xes/common/fsl_8xxx_clk.c b/board/xes/common/fsl_8xxx_clk.c
index f4a17b7..20d0a30 100644
--- a/board/xes/common/fsl_8xxx_clk.c
+++ b/board/xes/common/fsl_8xxx_clk.c
@@ -38,7 +38,11 @@ unsigned long get_board_sys_clk(ulong dummy)
 	if (in_be32(&gur->gpporcr) & 0x10000)
 		return 66666666;
 	else
+#ifdef CONFIG_P2020
+		return 100000000;
+#else
 		return 50000000;
+#endif
 }
 
 #ifdef CONFIG_MPC85xx
@@ -54,6 +58,13 @@ unsigned long get_board_ddr_clk(ulong dummy)
 	if (ddr_ratio == 0x7)
 		return get_board_sys_clk(dummy);
 
+#ifdef CONFIG_P2020
+	if (in_be32(&gur->gpporcr) & 0x20000)
+		return 66666666;
+	else
+		return 100000000;
+#else
 	return 66666666;
+#endif
 }
 #endif
diff --git a/board/xes/common/fsl_8xxx_misc.c b/board/xes/common/fsl_8xxx_misc.c
new file mode 100644
index 0000000..b7fa695
--- /dev/null
+++ b/board/xes/common/fsl_8xxx_misc.c
@@ -0,0 +1,62 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+#ifdef CONFIG_PCA953X
+#include <pca953x.h>
+
+/*
+ * Determine if a board's flashes are write protected
+ */
+int board_flash_wp_on(void)
+{
+	if (pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) &
+			CONFIG_SYS_PCA953X_NVM_WP)
+		return 1;
+
+	return 0;
+}
+#endif
+
+/*
+ * Return a board's derivative model number.  For example:
+ * return 2 for the XPedite5372 and return 1 for the XPedite5201.
+ */
+uint get_board_derivative(void)
+{
+#if defined(CONFIG_MPC85xx)
+       volatile ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+#elif defined(CONFIG_MPC86xx)
+       volatile immap_t *immap = (immap_t *)CONFIG_SYS_CCSRBAR;
+       volatile ccsr_gur_t *gur = &immap->im_gur;
+#endif
+
+       /*
+        * The top 4 lines of the local bus address are pulled low/high and
+        * can be read to determine the least significant digit of a board's
+        * model number.
+        */
+       return gur->gpporcr >> 28;
+}
+
+
diff --git a/board/trizepsiv/pxavoltage.S b/board/xes/common/fsl_8xxx_misc.h
index 9659c2b..ecc70da 100644
--- a/board/trizepsiv/pxavoltage.S
+++ b/board/xes/common/fsl_8xxx_misc.h
@@ -1,6 +1,5 @@
 /*
- * (C) Copyright 2007
- * Stefano Babic, DENX Gmbh, sbabic@denx.de
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -12,7 +11,7 @@
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
@@ -21,9 +20,9 @@
  * MA 02111-1307 USA
  */
 
-#include <asm/arch/pxa-regs.h>
+#ifndef __FSL_8XXX_MISC_H___
+#define __FSL_8XXX_MISC_H___
 
-		.global	initPXAvoltage
+uint get_board_derivative(void);
 
-initPXAvoltage:
-		mov	pc, lr
+#endif /* __FSL_8XXX_MISC_H__ */
diff --git a/board/xes/common/fsl_8xxx_pci.c b/board/xes/common/fsl_8xxx_pci.c
index ece7882..f425cee 100644
--- a/board/xes/common/fsl_8xxx_pci.c
+++ b/board/xes/common/fsl_8xxx_pci.c
@@ -25,10 +25,10 @@
 #include <pci.h>
 #include <asm/fsl_pci.h>
 #include <asm/io.h>
+#include <linux/compiler.h>
 #include <libfdt.h>
 #include <fdt_support.h>
 
-int first_free_busno = 0;
 
 #ifdef CONFIG_PCI1
 static struct pci_controller pci1_hose;
@@ -43,111 +43,6 @@ static struct pci_controller pcie2_hose;
 static struct pci_controller pcie3_hose;
 #endif
 
-#ifdef CONFIG_MPC8572
-/* Correlate host/agent POR bits to usable info. Table 4-14 */
-struct host_agent_cfg_t {
-	uchar pcie_root[3];
-	uchar rio_host;
-} host_agent_cfg[8] = {
-	{{0, 0, 0}, 0},
-	{{0, 1, 1}, 1},
-	{{1, 0, 1}, 0},
-	{{1, 1, 0}, 1},
-	{{0, 0, 1}, 0},
-	{{0, 1, 0}, 1},
-	{{1, 0, 0}, 0},
-	{{1, 1, 1}, 1}
-};
-
-/* Correlate port width POR bits to usable info. Table 4-15 */
-struct io_port_cfg_t {
-	uchar pcie_width[3];
-	uchar rio_width;
-} io_port_cfg[16] = {
-	{{0, 0, 0}, 0},
-	{{0, 0, 0}, 0},
-	{{4, 0, 0}, 0},
-	{{4, 4, 0}, 0},
-	{{0, 0, 0}, 0},
-	{{0, 0, 0}, 0},
-	{{0, 0, 0}, 4},
-	{{4, 2, 2}, 0},
-	{{0, 0, 0}, 0},
-	{{0, 0, 0}, 0},
-	{{0, 0, 0}, 0},
-	{{4, 0, 0}, 4},
-	{{4, 0, 0}, 4},
-	{{0, 0, 0}, 4},
-	{{0, 0, 0}, 4},
-	{{8, 0, 0}, 0},
-};
-#elif defined CONFIG_MPC8548
-/* Correlate host/agent POR bits to usable info. Table 4-12 */
-struct host_agent_cfg_t {
-	uchar pci_host[2];
-	uchar pcie_root[1];
-	uchar rio_host;
-} host_agent_cfg[8] = {
-	{{1, 1}, {0}, 0},
-	{{1, 1}, {1}, 0},
-	{{1, 1}, {0}, 1},
-	{{0, 0}, {0}, 0}, /* reserved */
-	{{0, 1}, {1}, 0},
-	{{1, 1}, {1}, 0},
-	{{0, 1}, {1}, 1},
-	{{1, 1}, {1}, 1}
-};
-
-/* Correlate port width POR bits to usable info. Table 4-13 */
-struct io_port_cfg_t {
-	uchar pcie_width[1];
-	uchar rio_width;
-} io_port_cfg[8] = {
-	{{0}, 0},
-	{{0}, 0},
-	{{0}, 0},
-	{{4}, 4},
-	{{4}, 4},
-	{{0}, 4},
-	{{0}, 4},
-	{{8}, 0},
-};
-#elif defined CONFIG_MPC86xx
-/* Correlate host/agent POR bits to usable info. Table 4-17 */
-struct host_agent_cfg_t {
-	uchar pcie_root[2];
-	uchar rio_host;
-} host_agent_cfg[8] = {
-	{{0, 0}, 0},
-	{{1, 0}, 1},
-	{{0, 1}, 0},
-	{{1, 1}, 1}
-};
-
-/* Correlate port width POR bits to usable info. Table 4-16 */
-struct io_port_cfg_t {
-	uchar pcie_width[2];
-	uchar rio_width;
-} io_port_cfg[16] = {
-	{{0, 0}, 0},
-	{{0, 0}, 0},
-	{{8, 0}, 0},
-	{{8, 8}, 0},
-	{{0, 0}, 0},
-	{{8, 0}, 4},
-	{{8, 0}, 4},
-	{{8, 0}, 4},
-	{{0, 0}, 0},
-	{{0, 0}, 4},
-	{{0, 0}, 4},
-	{{0, 0}, 4},
-	{{0, 0}, 0},
-	{{0, 0}, 0},
-	{{0, 8}, 0},
-	{{8, 8}, 0},
-};
-#endif
-
 /*
  * 85xx and 86xx share naming conventions, but different layout.
  * Correlate names to CPU-specific values to share common
@@ -173,22 +68,22 @@ struct io_port_cfg_t {
 
 void pci_init_board(void)
 {
-	struct pci_controller *hose;
-	volatile ccsr_fsl_pci_t *pci;
-	int width;
-	int host;
+	struct fsl_pci_info pci_info[3];
+	int first_free_busno = 0;
+	int num = 0;
+	int pcie_ep;
+	__maybe_unused int pcie_configured;
+
 #if defined(CONFIG_MPC85xx)
 	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
 #elif defined(CONFIG_MPC86xx)
 	immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
 	volatile ccsr_gur_t *gur = &immap->im_gur;
 #endif
-	uint devdisr = in_be32(&gur->devdisr);
-	uint io_sel = (in_be32(&gur->pordevsr) & MPC8xxx_PORDEVSR_IO_SEL) >>
+	u32 devdisr = in_be32(&gur->devdisr);
+	u32 pordevsr = in_be32(&gur->pordevsr);
+	__maybe_unused uint io_sel = (pordevsr & MPC8xxx_PORDEVSR_IO_SEL) >>
 			MPC8xxx_PORDEVSR_IO_SEL_SHIFT;
-	uint host_agent = (in_be32(&gur->porbmsr) & MPC8xxx_PORBMSR_HA) >>
-			MPC8xxx_PORBMSR_HA_SHIFT;
-	struct pci_region *r;
 
 #ifdef CONFIG_PCI1
 	uint pci_spd_norm = in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_PCI1_SPD;
@@ -197,49 +92,19 @@ void pci_init_board(void)
 	uint pcix = in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_PCI1;
 	uint freq = CONFIG_SYS_CLK_FREQ / 1000 / 1000;
 
-	width = 0; /* Silence compiler warning... */
-	io_sel &= 0xf; /* Silence compiler warning... */
-	pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
-	hose = &pci1_hose;
-	host = host_agent_cfg[host_agent].pci_host[0];
-	r = hose->regions;
-
 	if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
+		SET_STD_PCI_INFO(pci_info[num], 1);
+		pcie_ep = fsl_setup_hose(&pci1_hose, pci_info[num].regs);
 		printf("\n    PCI1: %d bit %s, %s %d MHz, %s, %s\n",
 			pci_32 ? 32 : 64,
 			pcix ? "PCIX" : "PCI",
 			pci_spd_norm ? ">=" : "<=",
 			pcix ? freq * 2 : freq,
-			host ? "host" : "agent",
+			pcie_ep ? "agent" : "host",
 			pci_arb ? "arbiter" : "external-arbiter");
 
-		/* outbound memory */
-		pci_set_region(r++,
-				CONFIG_SYS_PCI1_MEM_BASE,
-				CONFIG_SYS_PCI1_MEM_PHYS,
-				CONFIG_SYS_PCI1_MEM_SIZE,
-				PCI_REGION_MEM);
-
-		/* outbound io */
-		pci_set_region(r++,
-				CONFIG_SYS_PCI1_IO_BASE,
-				CONFIG_SYS_PCI1_IO_PHYS,
-				CONFIG_SYS_PCI1_IO_SIZE,
-				PCI_REGION_IO);
-
-		hose->region_count = r - hose->regions;
-
-		hose->first_busno = first_free_busno;
-
-		fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
-
-		/* Unlock inbound PCI configuration cycles */
-		if (!host)
-			fsl_pci_config_unlock(hose);
-
-		first_free_busno = hose->last_busno + 1;
-		printf("    PCI1 on bus %02x - %02x\n",
-			hose->first_busno, hose->last_busno);
+		first_free_busno = fsl_pci_init_port(&pci_info[num++],
+					&pci1_hose, first_free_busno);
 	} else {
 		printf("    PCI1: disabled\n");
 	}
@@ -247,148 +112,53 @@ void pci_init_board(void)
 	/* PCI1 not present on MPC8572 */
 	setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1);
 #endif
-#ifdef CONFIG_PCIE1
-	pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
-	hose = &pcie1_hose;
-	host = host_agent_cfg[host_agent].pcie_root[0];
-	width = io_port_cfg[io_sel].pcie_width[0];
-	r = hose->regions;
-
-	if (width && !(devdisr & MPC8xxx_DEVDISR_PCIE1)) {
-		printf("\n    PCIE1 connected as %s (x%d)",
-			host ? "Root Complex" : "Endpoint", width);
-		if (in_be32(&pci->pme_msg_det)) {
-			out_be32(&pci->pme_msg_det, 0xffffffff);
-			debug(" with errors.  Clearing.  Now 0x%08x",
-				in_be32(&pci->pme_msg_det));
-		}
-		printf("\n");
-
-		/* outbound memory */
-		pci_set_region(r++,
-				CONFIG_SYS_PCIE1_MEM_BASE,
-				CONFIG_SYS_PCIE1_MEM_PHYS,
-				CONFIG_SYS_PCIE1_MEM_SIZE,
-				PCI_REGION_MEM);
-
-		/* outbound io */
-		pci_set_region(r++,
-				CONFIG_SYS_PCIE1_IO_BASE,
-				CONFIG_SYS_PCIE1_IO_PHYS,
-				CONFIG_SYS_PCIE1_IO_SIZE,
-				PCI_REGION_IO);
-
-		hose->region_count = r - hose->regions;
-
-		hose->first_busno = first_free_busno;
-
-		fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
 
-		/* Unlock inbound PCI configuration cycles */
-		if (!host)
-			fsl_pci_config_unlock(hose);
-
-		first_free_busno = hose->last_busno + 1;
-		printf("    PCIE1 on bus %02x - %02x\n",
-				hose->first_busno, hose->last_busno);
+#ifdef CONFIG_PCIE1
+	pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel);
+
+	if (pcie_configured && !(devdisr & MPC8xxx_DEVDISR_PCIE1)) {
+		SET_STD_PCIE_INFO(pci_info[num], 1);
+		pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs);
+		printf("    PCIE1 connected as %s\n",
+			pcie_ep ? "Endpoint" : "Root Complex");
+		first_free_busno = fsl_pci_init_port(&pci_info[num++],
+					&pcie1_hose, first_free_busno);
+	} else {
+		printf("    PCIE1: disabled\n");
 	}
 #else
 	setbits_be32(&gur->devdisr, MPC8xxx_DEVDISR_PCIE1);
 #endif /* CONFIG_PCIE1 */
 
 #ifdef CONFIG_PCIE2
-	pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR;
-	hose = &pcie2_hose;
-	host = host_agent_cfg[host_agent].pcie_root[1];
-	width = io_port_cfg[io_sel].pcie_width[1];
-	r = hose->regions;
-
-	if (width && !(devdisr & MPC8xxx_DEVDISR_PCIE2)) {
-		printf("\n    PCIE2 connected as %s (x%d)",
-			host ? "Root Complex" : "Endpoint", width);
-		if (in_be32(&pci->pme_msg_det)) {
-			out_be32(&pci->pme_msg_det, 0xffffffff);
-			debug(" with errors.  Clearing.  Now 0x%08x",
-				in_be32(&pci->pme_msg_det));
-		}
-		printf("\n");
-
-		/* outbound memory */
-		pci_set_region(r++,
-				CONFIG_SYS_PCIE2_MEM_BASE,
-				CONFIG_SYS_PCIE2_MEM_PHYS,
-				CONFIG_SYS_PCIE2_MEM_SIZE,
-				PCI_REGION_MEM);
-
-		/* outbound io */
-		pci_set_region(r++,
-				CONFIG_SYS_PCIE2_IO_BASE,
-				CONFIG_SYS_PCIE2_IO_PHYS,
-				CONFIG_SYS_PCIE2_IO_SIZE,
-				PCI_REGION_IO);
-
-		hose->region_count = r - hose->regions;
-
-		hose->first_busno = first_free_busno;
-
-		fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
-
-		/* Unlock inbound PCI configuration cycles */
-		if (!host)
-			fsl_pci_config_unlock(hose);
-
-		first_free_busno = hose->last_busno + 1;
-		printf("    PCIE2 on bus %02x - %02x\n",
-				hose->first_busno, hose->last_busno);
+	pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_2, io_sel);
+
+	if (pcie_configured && !(devdisr & MPC8xxx_DEVDISR_PCIE2)) {
+		SET_STD_PCIE_INFO(pci_info[num], 2);
+		pcie_ep = fsl_setup_hose(&pcie2_hose, pci_info[num].regs);
+		printf("    PCIE2 connected as %s\n",
+			pcie_ep ? "Endpoint" : "Root Complex");
+		first_free_busno = fsl_pci_init_port(&pci_info[num++],
+					&pcie2_hose, first_free_busno);
+	} else {
+		printf("    PCIE2: disabled\n");
 	}
 #else
 	setbits_be32(&gur->devdisr, MPC8xxx_DEVDISR_PCIE2);
 #endif /* CONFIG_PCIE2 */
 
 #ifdef CONFIG_PCIE3
-	pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE3_ADDR;
-	hose = &pcie3_hose;
-	host = host_agent_cfg[host_agent].pcie_root[2];
-	width = io_port_cfg[io_sel].pcie_width[2];
-	r = hose->regions;
-
-	if (width && !(devdisr & MPC8xxx_DEVDISR_PCIE3)) {
-		printf("\n    PCIE3 connected as %s (x%d)",
-			host ? "Root Complex" : "Endpoint", width);
-		if (in_be32(&pci->pme_msg_det)) {
-			out_be32(&pci->pme_msg_det, 0xffffffff);
-			debug(" with errors.  Clearing.  Now 0x%08x",
-				in_be32(&pci->pme_msg_det));
-		}
-		printf("\n");
-
-		/* outbound memory */
-		pci_set_region(r++,
-				CONFIG_SYS_PCIE3_MEM_BASE,
-				CONFIG_SYS_PCIE3_MEM_PHYS,
-				CONFIG_SYS_PCIE3_MEM_SIZE,
-				PCI_REGION_MEM);
-
-		/* outbound io */
-		pci_set_region(r++,
-				CONFIG_SYS_PCIE3_IO_BASE,
-				CONFIG_SYS_PCIE3_IO_PHYS,
-				CONFIG_SYS_PCIE3_IO_SIZE,
-				PCI_REGION_IO);
-
-		hose->region_count = r - hose->regions;
-
-		hose->first_busno = first_free_busno;
-
-		fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
-
-		/* Unlock inbound PCI configuration cycles */
-		if (!host)
-			fsl_pci_config_unlock(hose);
-
-		first_free_busno = hose->last_busno + 1;
-		printf("    PCIE3 on bus %02x - %02x\n",
-				hose->first_busno, hose->last_busno);
+	pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_3, io_sel);
+
+	if (pcie_configured && !(devdisr & MPC8xxx_DEVDISR_PCIE3)) {
+		SET_STD_PCIE_INFO(pci_info[num], 3);
+		pcie_ep = fsl_setup_hose(&pcie3_hose, pci_info[num].regs);
+		printf("    PCIE3 connected as %s\n",
+			pcie_ep ? "Endpoint" : "Root Complex");
+		first_free_busno = fsl_pci_init_port(&pci_info[num++],
+					&pcie3_hose, first_free_busno);
+	} else {
+		printf("    PCIE3: disabled\n");
 	}
 #else
 	setbits_be32(&gur->devdisr, MPC8xxx_DEVDISR_PCIE3);
diff --git a/board/xes/xpedite5170/Makefile b/board/xes/xpedite517x/Makefile
index fea6686..fea6686 100644
--- a/board/xes/xpedite5170/Makefile
+++ b/board/xes/xpedite517x/Makefile
diff --git a/board/xes/xpedite5170/ddr.c b/board/xes/xpedite517x/ddr.c
index 1d57d09..1d57d09 100644
--- a/board/xes/xpedite5170/ddr.c
+++ b/board/xes/xpedite517x/ddr.c
diff --git a/board/xes/xpedite5170/law.c b/board/xes/xpedite517x/law.c
index 0b7d9ef..0b7d9ef 100644
--- a/board/xes/xpedite5170/law.c
+++ b/board/xes/xpedite517x/law.c
diff --git a/board/xes/xpedite5170/xpedite5170.c b/board/xes/xpedite517x/xpedite517x.c
index 5822941..0f7fa6c 100644
--- a/board/xes/xpedite5170/xpedite5170.c
+++ b/board/xes/xpedite517x/xpedite517x.c
@@ -26,30 +26,12 @@
 #include <asm/io.h>
 #include <fdt_support.h>
 #include <pca953x.h>
+#include "../common/fsl_8xxx_misc.h"
 
 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_PCI)
 extern void ft_board_pci_setup(void *blob, bd_t *bd);
 #endif
 
-int checkboard(void)
-{
-	char *s;
-
-	printf("Board: X-ES %s 3U VPX SBC\n", CONFIG_SYS_BOARD_NAME);
-	printf("       ");
-	s = getenv("board_rev");
-	if (s)
-		printf("Rev %s, ", s);
-	s = getenv("serial#");
-	if (s)
-		printf("Serial# %s, ", s);
-	s = getenv("board_cfg");
-	if (s)
-		printf("Cfg %s", s);
-	printf("\n");
-
-	return 0;
-}
 /*
  * Print out which flash was booted from and if booting from the 2nd flash,
  * swap flash chip selects to maintain consistent flash numbering/addresses.
diff --git a/board/xes/xpedite5200/Makefile b/board/xes/xpedite520x/Makefile
index 02fe8fc..02fe8fc 100644
--- a/board/xes/xpedite5200/Makefile
+++ b/board/xes/xpedite520x/Makefile
diff --git a/board/xes/xpedite5200/ddr.c b/board/xes/xpedite520x/ddr.c
index c5616d5..c5616d5 100644
--- a/board/xes/xpedite5200/ddr.c
+++ b/board/xes/xpedite520x/ddr.c
diff --git a/board/xes/xpedite5200/law.c b/board/xes/xpedite520x/law.c
index bbfcb9d..bbfcb9d 100644
--- a/board/xes/xpedite5200/law.c
+++ b/board/xes/xpedite520x/law.c
diff --git a/board/xes/xpedite5200/tlb.c b/board/xes/xpedite520x/tlb.c
index bd7bff8..bd7bff8 100644
--- a/board/xes/xpedite5200/tlb.c
+++ b/board/xes/xpedite520x/tlb.c
diff --git a/board/xes/xpedite5200/xpedite5200.c b/board/xes/xpedite520x/xpedite520x.c
index a2627f8..dc5c965 100644
--- a/board/xes/xpedite5200/xpedite5200.c
+++ b/board/xes/xpedite520x/xpedite520x.c
@@ -36,33 +36,6 @@
 
 extern void ft_board_pci_setup(void *blob, bd_t *bd);
 
-int checkboard(void)
-{
-	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-	volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
-	char *s;
-
-	printf("Board: X-ES %s PMC\n", CONFIG_SYS_BOARD_NAME);
-	printf("       ");
-	s = getenv("board_rev");
-	if (s)
-		printf("Rev %s, ", s);
-	s = getenv("serial#");
-	if (s)
-		printf("Serial# %s, ", s);
-	s = getenv("board_cfg");
-	if (s)
-		printf("Cfg %s", s);
-	printf("\n");
-
-	out_be32(&lbc->ltesr, 0xffffffff);	/* Clear LBC error IRQs */
-	out_be32(&lbc->lteir, 0xffffffff);	/* Enable LBC error IRQs */
-	out_be32(&ecm->eedr, 0xffffffff);	/* Clear ecm errors */
-	out_be32(&ecm->eeer, 0xffffffff);	/* Enable ecm errors */
-
-	return 0;
-}
-
 static void flash_cs_fixup(void)
 {
 	int flash_sel;
diff --git a/board/xes/xpedite5370/Makefile b/board/xes/xpedite537x/Makefile
index 919397c..919397c 100644
--- a/board/xes/xpedite5370/Makefile
+++ b/board/xes/xpedite537x/Makefile
diff --git a/board/xes/xpedite5370/ddr.c b/board/xes/xpedite537x/ddr.c
index 4d3f255..4d3f255 100644
--- a/board/xes/xpedite5370/ddr.c
+++ b/board/xes/xpedite537x/ddr.c
diff --git a/board/xes/xpedite5370/law.c b/board/xes/xpedite537x/law.c
index daee676..daee676 100644
--- a/board/xes/xpedite5370/law.c
+++ b/board/xes/xpedite537x/law.c
diff --git a/board/xes/xpedite5370/tlb.c b/board/xes/xpedite537x/tlb.c
index a465ce3..a465ce3 100644
--- a/board/xes/xpedite5370/tlb.c
+++ b/board/xes/xpedite537x/tlb.c
diff --git a/board/xes/xpedite5370/xpedite5370.c b/board/xes/xpedite537x/xpedite537x.c
index 2a060c2..89fa6c7 100644
--- a/board/xes/xpedite5370/xpedite5370.c
+++ b/board/xes/xpedite537x/xpedite537x.c
@@ -36,26 +36,6 @@ DECLARE_GLOBAL_DATA_PTR;
 
 extern void ft_board_pci_setup(void *blob, bd_t *bd);
 
-int checkboard(void)
-{
-	char *s;
-
-	printf("Board: X-ES %s 3U VPX SBC\n", CONFIG_SYS_BOARD_NAME);
-	printf("       ");
-	s = getenv("board_rev");
-	if (s)
-		printf("Rev %s, ", s);
-	s = getenv("serial#");
-	if (s)
-		printf("Serial# %s, ", s);
-	s = getenv("board_cfg");
-	if (s)
-		printf("Cfg %s", s);
-	printf("\n");
-
-	return 0;
-}
-
 static void flash_cs_fixup(void)
 {
 	int flash_sel;
diff --git a/board/xes/xpedite550x/Makefile b/board/xes/xpedite550x/Makefile
new file mode 100644
index 0000000..8980a4b
--- /dev/null
+++ b/board/xes/xpedite550x/Makefile
@@ -0,0 +1,39 @@
+#
+# Copyright 2007-2008 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= ddr.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+
+SRCS	:= $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS-y))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/xes/xpedite550x/ddr.c b/board/xes/xpedite550x/ddr.c
new file mode 100644
index 0000000..718cd98
--- /dev/null
+++ b/board/xes/xpedite550x/ddr.c
@@ -0,0 +1,165 @@
+/*
+ * Copyright 2010 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
+		 sizeof(ddr3_spd_eeprom_t));
+}
+
+void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0)
+			i2c_address = SPD_EEPROM_ADDRESS1;
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+/*
+ *     There are traditionally three board-specific SDRAM timing parameters
+ *     which must be calculated based on the particular PCB artwork.  These are:
+ *     1.) CPO (Read Capture Delay)
+ *             - TIMING_CFG_2 register
+ *             Source: Calculation based on board trace lengths and
+ *                     chip-specific internal delays.
+ *     2.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
+ *             - DDR_SDRAM_CLK_CNTL register
+ *             Source: Signal Integrity Simulations
+ *     3.) 2T Timing on Addr/Ctl
+ *             - TIMING_CFG_2 register
+ *             Source: Signal Integrity Simulations
+ *             Usually only needed with heavy load/very high speed (>DDR2-800)
+ *
+ *     ====== XPedite550x DDR3-800 read delay calculations ======
+ *
+ *     The P2020 processor provides an autoleveling option. Setting CPO to
+ *     0x1f enables this auto configuration.
+ */
+
+typedef struct {
+	unsigned short datarate_mhz_low;
+	unsigned short datarate_mhz_high;
+	unsigned char clk_adjust;
+	unsigned char cpo;
+} board_specific_parameters_t;
+
+const board_specific_parameters_t board_specific_parameters[][20] = {
+	{
+		/* Controller 0 */
+                {
+			/* DDR3-600/667 */
+			.datarate_mhz_low	= 500,
+			.datarate_mhz_high	= 750,
+			.clk_adjust		= 5,
+			.cpo			= 31,
+		},
+                {
+			/* DDR3-800 */
+			.datarate_mhz_low	= 750,
+			.datarate_mhz_high	= 850,
+			.clk_adjust		= 5,
+			.cpo			= 31,
+		},
+	},
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const board_specific_parameters_t *pbsp =
+				&(board_specific_parameters[ctrl_num][0]);
+	u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
+				sizeof(board_specific_parameters[0][0]);
+	u32 i;
+	ulong ddr_freq;
+
+	/*
+	 * Set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+	 * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
+	 * there are two dimms in the controller, set odt_rd_cfg to 3 and
+	 * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
+	 */
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		if (i&1) {	/* odd CS */
+			popts->cs_local_opts[i].odt_rd_cfg = 0;
+			popts->cs_local_opts[i].odt_wr_cfg = 0;
+		} else {	/* even CS */
+			if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
+				popts->cs_local_opts[i].odt_rd_cfg = 0;
+				popts->cs_local_opts[i].odt_wr_cfg = 4;
+			} else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
+				popts->cs_local_opts[i].odt_rd_cfg = 3;
+				popts->cs_local_opts[i].odt_wr_cfg = 3;
+			}
+		}
+	}
+
+	/*
+	 * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+
+	for (i = 0; i < num_params; i++) {
+		if (ddr_freq >= pbsp->datarate_mhz_low &&
+		    ddr_freq <= pbsp->datarate_mhz_high) {
+			popts->clk_adjust = pbsp->clk_adjust;
+			popts->cpo_override = pbsp->cpo;
+			popts->twoT_en = 0;
+		}
+		pbsp++;
+	}
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+
+	/*
+	 * Enable on-die termination.
+	 * From the Micron Technical Node TN-41-04, RTT_Nom should typically
+	 * be 30 to 40 ohms, while RTT_WR should be 120 ohms.  Setting RTT_WR
+	 * is handled in the Freescale DDR3 driver.  Set RTT_Nom here.
+	 */
+	popts->rtt_override = 1;
+	popts->rtt_override_value = 3;
+}
+
diff --git a/board/xes/xpedite550x/law.c b/board/xes/xpedite550x/law.c
new file mode 100644
index 0000000..4d4445d
--- /dev/null
+++ b/board/xes/xpedite550x/law.c
@@ -0,0 +1,54 @@
+/*
+ * Copyright 2010 Extreme Engineering Solutions, Inc.
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+/*
+ * Notes:
+ *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ *    If flash is 8M at default position (last 8M), no LAW needed.
+ */
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_PCIE1_MEM_PHYS
+	SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_1G, LAW_TRGT_IF_PCIE_1),
+	SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_1),
+#endif
+#ifdef CONFIG_SYS_PCIE2_MEM_PHYS
+	SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_2),
+	SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_2),
+#endif
+#ifdef CONFIG_SYS_PCIE3_MEM_PHYS
+	SET_LAW(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_3),
+	SET_LAW(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_3),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/xes/xpedite550x/tlb.c b/board/xes/xpedite550x/tlb.c
new file mode 100644
index 0000000..cf3ff4d
--- /dev/null
+++ b/board/xes/xpedite550x/tlb.c
@@ -0,0 +1,98 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+		MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* W**G* - NOR flashes */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+		0, 0, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, 1, BOOKE_PAGESZ_1M, 1),
+
+	/* *I*G* - NAND flash */
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, 2, BOOKE_PAGESZ_1M, 1),
+
+	/* **M** - Boot page for secondary processors */
+	SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
+		0, 3, BOOKE_PAGESZ_4K, 1),
+
+#ifdef CONFIG_PCIE1
+	/* *I*G* - PCIe */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, 4, BOOKE_PAGESZ_1G, 1),
+#endif
+
+#ifdef CONFIG_PCIE2
+	/* *I*G* - PCIe */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, 5, BOOKE_PAGESZ_256M, 1),
+#endif
+
+#ifdef CONFIG_PCIE3
+	/* *I*G* - PCIe */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, 6, BOOKE_PAGESZ_256M, 1),
+#endif
+
+#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
+	/* *I*G* - PCIe */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, 7, BOOKE_PAGESZ_64M, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/xes/xpedite550x/xpedite550x.c b/board/xes/xpedite550x/xpedite550x.c
new file mode 100644
index 0000000..2ad30a3
--- /dev/null
+++ b/board/xes/xpedite550x/xpedite550x.c
@@ -0,0 +1,107 @@
+/*
+ * Copyright 2010 Extreme Engineering Solutions, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <asm/io.h>
+#include <asm/cache.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pca953x.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern void ft_board_pci_setup(void *blob, bd_t *bd);
+
+static void flash_cs_fixup(void)
+{
+	int flash_sel;
+
+	/*
+	 * Print boot dev and swap flash flash chip selects if booted from 2nd
+	 * flash.  Swapping chip selects presents user with a common memory
+	 * map regardless of which flash was booted from.
+	 */
+	flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) &
+			CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS));
+	printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1);
+
+	if (flash_sel) {
+		set_lbc_br(0, CONFIG_SYS_BR1_PRELIM);
+		set_lbc_or(0, CONFIG_SYS_OR1_PRELIM);
+
+		set_lbc_br(1, CONFIG_SYS_BR0_PRELIM);
+		set_lbc_or(1, CONFIG_SYS_OR0_PRELIM);
+	}
+}
+
+int board_early_init_r(void)
+{
+	/* Initialize PCA9557 devices */
+	pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0);
+	pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0);
+	pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0);
+	pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0);
+
+	/*
+	 * Remap NOR flash region to caching-inhibited
+	 * so that flash can be erased/programmed properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* Invalidate existing TLB entry for NOR flash */
+	disable_tlb(0);
+	set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
+		(CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, 0, BOOKE_PAGESZ_256M, 1);
+
+	flash_cs_fixup();
+
+	return 0;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+#ifdef CONFIG_PCI
+	ft_board_pci_setup(blob, bd);
+#endif
+	ft_cpu_setup(blob, bd);
+}
+#endif
+
+#ifdef CONFIG_MP
+extern void cpu_mp_lmb_reserve(struct lmb *lmb);
+
+void board_lmb_reserve(struct lmb *lmb)
+{
+	cpu_mp_lmb_reserve(lmb);
+}
+#endif
diff --git a/board/xm250/Makefile b/board/xm250/Makefile
index a174f66..11e2b30 100644
--- a/board/xm250/Makefile
+++ b/board/xm250/Makefile
@@ -26,17 +26,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= xm250.o flash.o
-SOBJS	:= lowlevel_init.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
-	rm -f $(SOBJS) $(OBJS)
+	rm -f $(OBJS)
 
 distclean:	clean
 	rm -f $(LIB) core *.bak $(obj).depend
diff --git a/board/xm250/config.mk b/board/xm250/config.mk
deleted file mode 100644
index a3fa0e5..0000000
--- a/board/xm250/config.mk
+++ /dev/null
@@ -1,35 +0,0 @@
-#
-# (C) Copyright 2003-2004
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-#
-# MicroSys XM250 board:
-#
-
-
-# This is the address where U-Boot lives in flash:
-#CONFIG_SYS_TEXT_BASE = 0
-
-# FIXME: armboot does only work correctly when being compiled
-# for the addresses _after_ relocation to RAM!! Otherwhise the
-# .bss segment is assumed in flash...
-CONFIG_SYS_TEXT_BASE = 0xA3F80000
diff --git a/board/xm250/lowlevel_init.S b/board/xm250/lowlevel_init.S
deleted file mode 100644
index 8230550..0000000
--- a/board/xm250/lowlevel_init.S
+++ /dev/null
@@ -1,519 +0,0 @@
-/*
- * Most of this taken from Redboot hal_platform_setup.h with cleanup
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-/* wait for coprocessor write complete */
-	.macro CPWAIT reg
-	mrc	p15,0,\reg,c2,c0,0
-	mov	\reg,\reg
-	sub	pc,pc,#4
-	.endm
-/*
-	.macro SET_LED val
-	ldr	r6, =CRADLE_LED_CLR_REG
-	ldr	r7, =0
-	str	r7, [r6]
-	ldr	r6, =CRADLE_LED_SET_REG
-	ldr	r7, =\val
-	str	r7, [r6]
-	.endm
-*/
-
-.globl lowlevel_init
-lowlevel_init:
-
-	mov	r10, lr
-
-	/* Set up GPIO pins first */
-
-	ldr	r0,   =GPSR0
-	ldr	r1,   =CONFIG_SYS_GPSR0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPSR1
-	ldr	r1,   =CONFIG_SYS_GPSR1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPSR2
-	ldr	r1,   =CONFIG_SYS_GPSR2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPCR0
-	ldr	r1,   =CONFIG_SYS_GPCR0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPCR1
-	ldr	r1,   =CONFIG_SYS_GPCR1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPCR2
-	ldr	r1,   =CONFIG_SYS_GPCR2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GRER0
-	ldr	r1,   =CONFIG_SYS_GRER0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GRER1
-	ldr	r1,   =CONFIG_SYS_GRER1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GRER2
-	ldr	r1,   =CONFIG_SYS_GRER2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GFER0
-	ldr	r1,   =CONFIG_SYS_GFER0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GFER1
-	ldr	r1,   =CONFIG_SYS_GFER1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GFER2
-	ldr	r1,   =CONFIG_SYS_GFER2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPDR0
-	ldr	r1,   =CONFIG_SYS_GPDR0_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPDR1
-	ldr	r1,   =CONFIG_SYS_GPDR1_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GPDR2
-	ldr	r1,   =CONFIG_SYS_GPDR2_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR0_L
-	ldr	r1,   =CONFIG_SYS_GAFR0_L_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR0_U
-	ldr	r1,   =CONFIG_SYS_GAFR0_U_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR1_L
-	ldr	r1,   =CONFIG_SYS_GAFR1_L_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR1_U
-	ldr	r1,   =CONFIG_SYS_GAFR1_U_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR2_L
-	ldr	r1,   =CONFIG_SYS_GAFR2_L_VAL
-	str	r1,   [r0]
-
-	ldr	r0,   =GAFR2_U
-	ldr	r1,   =CONFIG_SYS_GAFR2_U_VAL
-	str	r1,   [r0]
-
-	/* enable GPIO pins */
-	ldr	r0,   =PSSR
-	ldr	r1,   =CONFIG_SYS_PSSR_VAL
-	str	r1,   [r0]
-
-	/* SET_LED 1 */
-
-	ldr	r3, =MSC1		/* low - bank 2 Lubbock Registers / SRAM */
-	ldr	r2, =CONFIG_SYS_MSC1_VAL	/* high - bank 3 Ethernet Controller */
-	str	r2, [r3]		/* need to set MSC1 before trying to write to the HEX LEDs */
-	ldr	r2, [r3]		/* need to read it back to make sure the value latches (see MSC section of manual) */
-
-
-/*********************************************************************
- *  Initlialize Memory Controller
- *
- *  See PXA250 Operating System Developer's Guide
- *
- *  pause for 200 uSecs- allow internal clocks to settle
- *  *Note: only need this if hard reset... doing it anyway for now
- */
-
-	@ Step 1
-	@ ---- Wait 200 usec
-	ldr	r3, =OSCR	@ reset the OS Timer Count to zero
-	mov	r2, #0
-	str	r2, [r3]
-	ldr	r4, =0x300	@ really 0x2E1 is about 200usec, so 0x300 should be plenty
-1:
-	ldr	r2, [r3]
-	cmp	r4, r2
-	bgt	1b
-
-	/* SET_LED 2 */
-
-mem_init:
-	@ get memory controller base address
-	ldr	r1,  =MEMC_BASE
-
-
-@****************************************************************************
-@  Step 2
-@
-
-	@ Step 2a
-	@ write msc0, read back to ensure data latches
-	@
-	ldr	r2,   =CONFIG_SYS_MSC0_VAL
-	str	r2,   [r1, #MSC0_OFFSET]
-	ldr	r2,   [r1, #MSC0_OFFSET]
-
-	@ write msc1
-	ldr	r2,  =CONFIG_SYS_MSC1_VAL
-	str	r2,  [r1, #MSC1_OFFSET]
-	ldr	r2,  [r1, #MSC1_OFFSET]
-
-	@ write msc2
-	ldr	r2,  =CONFIG_SYS_MSC2_VAL
-	str	r2,  [r1, #MSC2_OFFSET]
-	ldr	r2,  [r1, #MSC2_OFFSET]
-
-	@ Step 2b
-	@ write mecr
-	ldr	r2,  =CONFIG_SYS_MECR_VAL
-	str	r2,  [r1, #MECR_OFFSET]
-
-	@ write mcmem0
-	ldr	r2,  =CONFIG_SYS_MCMEM0_VAL
-	str	r2,  [r1, #MCMEM0_OFFSET]
-
-	@ write mcmem1
-	ldr	r2,  =CONFIG_SYS_MCMEM1_VAL
-	str	r2,  [r1, #MCMEM1_OFFSET]
-
-	@ write mcatt0
-	ldr	r2,  =CONFIG_SYS_MCATT0_VAL
-	str	r2,  [r1, #MCATT0_OFFSET]
-
-	@ write mcatt1
-	ldr	r2,  =CONFIG_SYS_MCATT1_VAL
-	str	r2,  [r1, #MCATT1_OFFSET]
-
-	@ write mcio0
-	ldr	r2,  =CONFIG_SYS_MCIO0_VAL
-	str	r2,  [r1, #MCIO0_OFFSET]
-
-	@ write mcio1
-	ldr	r2,  =CONFIG_SYS_MCIO1_VAL
-	str	r2,  [r1, #MCIO1_OFFSET]
-
-	/*SET_LED 3 */
-
-	@ Step 2c
-	@ fly-by-dma is defeatured on this part
-	@ write flycnfg
-	@ldr	r2,  =CONFIG_SYS_FLYCNFG_VAL
-	@str	r2,  [r1, #FLYCNFG_OFFSET]
-
-/* FIXME Does this sequence really make sense */
-#ifdef REDBOOT_WAY
-	@ Step 2d
-	@ get the mdrefr settings
-	ldr	r3,  =CONFIG_SYS_MDREFR_VAL
-
-	@ extract DRI field (we need a valid DRI field)
-	@
-	ldr	r2,  =0xFFF
-
-	@ valid DRI field in r3
-	@
-	and	r3,  r3,  r2
-
-	@ get the reset state of MDREFR
-	@
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-
-	@ clear the DRI field
-	@
-	bic	r4,  r4,  r2
-
-	@ insert the valid DRI field loaded above
-	@
-	orr	r4,  r4,  r3
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-
-	@ *Note: preserve the mdrefr value in r4 *
-
-	/*SET_LED 4 */
-
-@****************************************************************************
-@  Step 3
-@
-@ NO SRAM
-
-	mov   pc, r10
-
-
-@****************************************************************************
-@  Step 4
-@
-
-	@ Assumes previous mdrefr value in r4, if not then read current mdrefr
-
-	@ clear the free-running clock bits
-	@ (clear K0Free, K1Free, K2Free
-	@
-	bic	r4,  r4,  #(0x00800000 | 0x01000000 | 0x02000000)
-
-	@ set K0RUN for CPLD clock
-	@
-	orr	r4,  r4, #0x00002000
-
-	@ set K1RUN if bank 0 installed
-	@
-	orr	r4,  r4, #0x00010000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-
-	@ deassert SLFRSH
-	@
-	bic	r4,  r4,  #0x00400000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-
-	@ assert E1PIN
-	@
-	orr	r4,  r4,  #0x00008000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-	nop
-	nop
-#else
-	@ Step 2d
-	@ get the mdrefr settings
-	ldr	r4,  =CONFIG_SYS_MDREFR_VAL
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-
-	@  Step 4
-
-	@ set K0RUN for FLASH clock
-	@
-	orr	r4,  r4, #0x00002000
-
-	@ set K1RUN for bank DRAM 0
-	@
-	orr	r4,  r4, #0x00010000
-
-	@ set K2RUN for bank PLD
-	@
-	orr	r4,  r4, #0x00040000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-
-	@ deassert SLFRSH
-	@
-	bic	r4,  r4,  #0x00400000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-
-	@ assert E1PIN
-	@
-	orr	r4,  r4,  #0x00008000
-
-	@ write back mdrefr
-	@
-	str	r4,  [r1, #MDREFR_OFFSET]
-	ldr	r4,  [r1, #MDREFR_OFFSET]
-	nop
-	nop
-#endif
-
-	@ Step 4d
-	@ fetch platform value of mdcnfg
-	@
-	ldr	r2,  =CONFIG_SYS_MDCNFG_VAL
-
-	@ disable all sdram banks
-	@
-	bic	r2,  r2,  #(MDCNFG_DE0 | MDCNFG_DE1)
-	bic	r2,  r2,  #(MDCNFG_DE2 | MDCNFG_DE3)
-
-	@ program banks 0/1 for bus width
-	@
-	bic	r2,  r2,  #MDCNFG_DWID0		@0=32-bit
-
-	@ write initial value of mdcnfg, w/o enabling sdram banks
-	@
-	str	r2,  [r1, #MDCNFG_OFFSET]
-
-	@ Step 4e
-	@ pause for 200 uSecs
-	@
-	ldr	r3, =OSCR	@ reset the OS Timer Count to zero
-	mov	r2, #0
-	str	r2, [r3]
-	ldr	r4, =0x300	@ really 0x2E1 is about 200usec, so 0x300 should be plenty
-1:
-	ldr	r2, [r3]
-	cmp	r4, r2
-	bgt	1b
-
-	/*SET_LED 5 */
-
-	/* Why is this here??? */
-	mov	r0, #0x78		@turn everything off
-	mcr	p15, 0, r0, c1, c0, 0	@(caches off, MMU off, etc.)
-
-	@ Step 4f
-	@ Access memory *not yet enabled* for CBR refresh cycles (8)
-	@ - CBR is generated for all banks
-
-	ldr	r2, =CONFIG_SYS_DRAM_BASE
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-	str	r2, [r2]
-
-	@ Step 4g
-	@get memory controller base address
-	@
-	ldr	r1,  =MEMC_BASE
-
-	@fetch current mdcnfg value
-	@
-	ldr	r3,  [r1, #MDCNFG_OFFSET]
-
-	@enable sdram bank 0 if installed (must do for any populated bank)
-	@
-	orr	r3,  r3,  #MDCNFG_DE0
-
-	@write back mdcnfg, enabling the sdram bank(s)
-	@
-	str	r3,  [r1, #MDCNFG_OFFSET]
-
-	@ Step 4h
-	@ write mdmrs
-	@
-	ldr	r2,  =CONFIG_SYS_MDMRS_VAL
-	str	r2,  [r1, #MDMRS_OFFSET]
-
-	@ Done Memory Init
-
-	/*SET_LED 6 */
-
-	@********************************************************************
-	@ Disable (mask) all interrupts at the interrupt controller
-	@
-
-	@ clear the interrupt level register (use IRQ, not FIQ)
-	@
-	mov	r1, #0
-	ldr	r2,  =ICLR
-	str	r1,  [r2]
-
-	@ Set interrupt mask register
-	@
-	ldr	r1,  =CONFIG_SYS_ICMR_VAL
-	ldr	r2,  =ICMR
-	str	r1,  [r2]
-
-	@ ********************************************************************
-	@ Disable the peripheral clocks, and set the core clock
-	@
-
-	@ Turn Off ALL on-chip peripheral clocks for re-configuration
-	@
-	ldr	r1,  =CKEN
-	mov	r2,  #0
-	str	r2,  [r1]
-
-	@ set core clocks
-	@
-	ldr	r2,  =CONFIG_SYS_CCCR_VAL
-	ldr	r1,  =CCCR
-	str	r2,  [r1]
-
-#ifdef ENABLE32KHZ
-	@ enable the 32Khz oscillator for RTC and PowerManager
-	@
-	ldr	r1,  =OSCC
-	mov	r2,  #OSCC_OON
-	str	r2,  [r1]
-
-	@ NOTE:	 spin here until OSCC.OOK get set,
-	@	 meaning the PLL has settled.
-	@
-60:
-	ldr	r2, [r1]
-	ands	r2, r2, #1
-	beq	60b
-#endif
-
-	@ Turn on needed clocks
-	@
-	ldr	r1,  =CKEN
-	ldr	r2,  =CONFIG_SYS_CKEN_VAL
-	str	r2,  [r1]
-
-	/*SET_LED 7 */
-
-/* Is this needed???? */
-#define NODEBUG
-#ifdef NODEBUG
-	/*Disable software and data breakpoints */
-	mov	r0,#0
-	mcr	p15,0,r0,c14,c8,0	/* ibcr0 */
-	mcr	p15,0,r0,c14,c9,0	/* ibcr1 */
-	mcr	p15,0,r0,c14,c4,0	/* dbcon */
-
-	/*Enable all debug functionality */
-	mov	r0,#0x80000000
-	mcr	p14,0,r0,c10,c0,0	/* dcsr */
-
-#endif
-
-	/*SET_LED 8 */
-
-	mov	pc, r10
-
-@ End lowlevel_init
diff --git a/board/xm250/xm250.c b/board/xm250/xm250.c
index 246bdde..3188cf2 100644
--- a/board/xm250/xm250.c
+++ b/board/xm250/xm250.c
@@ -56,6 +56,10 @@ int
 board_init (void)
 /**********************************************************/
 {
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
+
 	/* arch number of MicroSys XM250 */
 	gd->bd->bi_arch_number = MACH_TYPE_XM250;
 
@@ -65,21 +69,18 @@ board_init (void)
 	return 0;
 }
 
-int
-/**********************************************************/
-dram_init (void)
-/**********************************************************/
+extern void pxa_dram_init(void);
+int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size  = PHYS_SDRAM_1_SIZE;
-	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size  = PHYS_SDRAM_2_SIZE;
-	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size  = PHYS_SDRAM_3_SIZE;
-	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size  = PHYS_SDRAM_4_SIZE;
+	pxa_dram_init();
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
 
-	return (0);
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
 }
 
 #ifdef CONFIG_CMD_NET
diff --git a/board/xsengine/Makefile b/board/xsengine/Makefile
deleted file mode 100644
index fc23935..0000000
--- a/board/xsengine/Makefile
+++ /dev/null
@@ -1,51 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).a
-
-COBJS	:= xsengine.o flash.o
-SOBJS	:= lowlevel_init.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-
-clean:
-	rm -f $(SOBJS) $(OBJS)
-
-distclean:	clean
-	rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/xsengine/config.mk b/board/xsengine/config.mk
deleted file mode 100644
index 821bb3b..0000000
--- a/board/xsengine/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0xA3F80000
diff --git a/board/xsengine/flash.c b/board/xsengine/flash.c
deleted file mode 100644
index 736905a..0000000
--- a/board/xsengine/flash.c
+++ /dev/null
@@ -1,470 +0,0 @@
-/*
- * (C) Copyright 2002
- * Robert Schwebel, Pengutronix, <r.schwebel@pengutronix.de>
- *
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-
-#define SWAP(x)               __swab32(x)
-
-flash_info_t	flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/* Functions */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static void flash_get_offsets (ulong base, flash_info_t *info);
-
-/*-----------------------------------------------------------------------
- */
-unsigned long flash_init (void)
-{
-	int i;
-	ulong size = 0;
-
-	for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
-		switch (i) {
-		case 0:
-			flash_get_size ((vu_long *) PHYS_FLASH_1, &flash_info[i]);
-			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
-			break;
-		case 1:
-			flash_get_size ((vu_long *) PHYS_FLASH_2, &flash_info[i]);
-			flash_get_offsets (PHYS_FLASH_2, &flash_info[i]);
-			break;
-		default:
-			panic ("configured too many flash banks!\n");
-			break;
-		}
-		size += flash_info[i].size;
-	}
-
-	/* Protect monitor and environment sectors */
-	flash_protect ( FLAG_PROTECT_SET,CONFIG_SYS_FLASH_BASE,CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1,&flash_info[0] );
-	flash_protect ( FLAG_PROTECT_SET,CONFIG_ENV_ADDR,CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0] );
-
-	return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) return;
-
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD) {
-		for (i = 0; i < info->sector_count; i++) {
-			info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
-			info->protect[i] = 0;
-		}
-	}
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info  (flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_AMD:	printf ("AMD ");		break;
-	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_AMLV640U:	printf ("AM29LV640ML (64Mbit, uniform sector size)\n");
-				break;
-	case FLASH_S29GL064M:	printf ("S29GL064M (64Mbit, top boot sector size)\n");
-				break;
-	default:		printf ("Unknown Chip Type\n");
-				break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     "
-		);
-	}
-	printf ("\n");
-	return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
-	short i;
-	ulong value;
-	ulong base = (ulong)addr;
-
-	/* Write auto select command: read Manufacturer ID */
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-	addr[0x0555] = 0x00900090;
-
-	value = addr[0];
-
-	debug ("Manuf. ID @ 0x%08lx: 0x%08lx\n", (ulong)addr, value);
-
-	switch (value) {
-	case AMD_MANUFACT:
-		debug ("Manufacturer: AMD\n");
-		info->flash_id = FLASH_MAN_AMD;
-		break;
-	case FUJ_MANUFACT:
-		debug ("Manufacturer: FUJITSU\n");
-		info->flash_id = FLASH_MAN_FUJ;
-		break;
-	default:
-		debug ("Manufacturer: *** unknown ***\n");
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		return (0);			/* no or unknown flash	*/
-	}
-
-	value = addr[1];			/* device ID		*/
-
-	debug ("Device ID @ 0x%08lx: 0x%08lx\n", (ulong)(&addr[1]), value);
-
-	switch (value) {
-
-	case AMD_ID_MIRROR:
-		debug ("Mirror Bit flash: addr[14] = %08lX  addr[15] = %08lX\n",
-			addr[14], addr[15]);
-		switch(addr[14]) {
-		case AMD_ID_LV640U_2:
-			if (addr[15] != AMD_ID_LV640U_3) {
-				debug ("Chip: AMLV640U -> unknown\n");
-				info->flash_id = FLASH_UNKNOWN;
-			} else {
-				debug ("Chip: AMLV640U\n");
-				info->flash_id += FLASH_AMLV640U;
-				info->sector_count = 128;
-				info->size = 0x01000000;
-			}
-			break;				/* => 16 MB	*/
-		case AMD_ID_GL064MT_2:
-			if (addr[15] != AMD_ID_GL064MT_3) {
-				debug ("Chip: S29GL064M-R3 -> unknown\n");
-				info->flash_id = FLASH_UNKNOWN;
-			} else {
-				debug ("Chip: S29GL064M-R3\n");
-				info->flash_id += FLASH_S29GL064M;
-				info->sector_count = 128;
-				info->size = 0x01000000;
-			}
-			break;				/* => 16 MB	*/
-		default:
-			debug ("Chip: *** unknown ***\n");
-			info->flash_id = FLASH_UNKNOWN;
-			break;
-		}
-		break;
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		return (0);			/* => no or unknown flash */
-	}
-
-	/* set up sector start address table */
-	switch (value) {
-	case AMD_ID_MIRROR:
-		switch (info->flash_id & FLASH_TYPEMASK) {
-		/* only known types here - no default */
-		case FLASH_AMLV128U:
-		case FLASH_AMLV640U:
-		case FLASH_AMLV320U:
-			for (i = 0; i < info->sector_count; i++) {
-				info->start[i] = base;
-				base += 0x20000;
-			}
-			break;
-		case FLASH_AMLV320B:
-			for (i = 0; i < info->sector_count; i++) {
-				info->start[i] = base;
-				/*
-				 * The first 8 sectors are 8 kB,
-				 * all the other ones  are 64 kB
-				 */
-				base += (i < 8)
-					?  2 * ( 8 << 10)
-					:  2 * (64 << 10);
-			}
-			break;
-		}
-		break;
-
-	default:
-		return (0);
-		break;
-	}
-
-#if 0
-	/* check for protected sectors */
-	for (i = 0; i < info->sector_count; i++) {
-		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
-		/* D0 = 1 if protected */
-		addr = (volatile unsigned long *)(info->start[i]);
-		info->protect[i] = addr[2] & 1;
-	}
-#endif
-
-	/*
-	 * Prevent writes to uninitialized FLASH.
-	 */
-	if (info->flash_id != FLASH_UNKNOWN) {
-		addr = (volatile unsigned long *)info->start[0];
-
-		*addr = 0x00F000F0;	/* reset bank */
-	}
-
-	return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	vu_long *addr = (vu_long*)(info->start[0]);
-	int flag, prot, sect, l_sect;
-	ulong start, now, last;
-
-	debug ("flash_erase: first: %d last: %d\n", s_first, s_last);
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if ((info->flash_id == FLASH_UNKNOWN) ||
-	    (info->flash_id > FLASH_AMD_COMP)) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-	l_sect = -1;
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-	addr[0x0555] = 0x00800080;
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect<=s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			addr = (vu_long*)(info->start[sect]);
-			addr[0] = 0x00300030;
-			l_sect = sect;
-		}
-	}
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* wait at least 80us - let's wait 1 ms */
-	udelay (1000);
-
-	/*
-	 * We wait for the last triggered sector
-	 */
-	if (l_sect < 0)
-		goto DONE;
-
-	start = get_timer (0);
-	last  = start;
-	addr = (vu_long*)(info->start[l_sect]);
-	while ((addr[0] & 0x00800080) != 0x00800080) {
-		if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
-			printf ("Timeout\n");
-			return 1;
-		}
-		/* show that we're waiting */
-		if ((now - last) > 100000) {	/* every second */
-			putc ('.');
-			last = now;
-		}
-	}
-
-DONE:
-	/* reset to read mode */
-	addr = (volatile unsigned long *)info->start[0];
-	addr[0] = 0x00F000F0;	/* reset bank */
-
-	printf (" done\n");
-	return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	wp = (addr & ~3);	/* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i=0, cp=wp; i<l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-		for (; i<4 && cnt>0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt==0 && i<4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		if ((rc = write_word(info, wp, SWAP(data))) != 0) {
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i=0; i<4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word(info, wp, SWAP(data))) != 0) {
-			return (rc);
-		}
-		wp  += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i<4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *)cp);
-	}
-
-	return (write_word(info, wp, SWAP(data)));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
-	vu_long *addr = (vu_long*)(info->start[0]);
-	ulong start;
-	int flag;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*((vu_long *)dest) & data) != data) {
-		return (2);
-	}
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-	addr[0x0555] = 0x00A000A0;
-
-	*((vu_long *)dest) = data;
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* data polling for D7 */
-	start = get_timer (0);
-	while ((*((vu_long *)dest) & 0x00800080) != (data & 0x00800080)) {
-		if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-			return (1);
-		}
-	}
-	return (0);
-}
diff --git a/board/xsengine/lowlevel_init.S b/board/xsengine/lowlevel_init.S
deleted file mode 100644
index 0d94ab6..0000000
--- a/board/xsengine/lowlevel_init.S
+++ /dev/null
@@ -1,221 +0,0 @@
-#include <config.h>
-#include <version.h>
-#include <asm/arch/pxa-regs.h>
-
-DRAM_SIZE:  .long   CONFIG_SYS_DRAM_SIZE
-
-.globl lowlevel_init
-lowlevel_init:
-
-   mov      r10, lr
-
-/* ---- GPIO INITIALISATION ---- */
-/* Set up GPIO pins first (3 groups [31:0] [63:32] [80:64]) */
-
-   /* General purpose set registers */
-   ldr      r0,   =GPSR0
-   ldr      r1,   =CONFIG_SYS_GPSR0_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GPSR1
-   ldr      r1,   =CONFIG_SYS_GPSR1_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GPSR2
-   ldr      r1,   =CONFIG_SYS_GPSR2_VAL
-   str      r1,   [r0]
-
-   /* General purpose clear registers */
-   ldr      r0,   =GPCR0
-   ldr      r1,   =CONFIG_SYS_GPCR0_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GPCR1
-   ldr      r1,   =CONFIG_SYS_GPCR1_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GPCR2
-   ldr      r1,   =CONFIG_SYS_GPCR2_VAL
-   str      r1,   [r0]
-
-   /* General rising edge registers */
-   ldr      r0,   =GRER0
-   ldr      r1,   =CONFIG_SYS_GRER0_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GRER1
-   ldr      r1,   =CONFIG_SYS_GRER1_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GRER2
-   ldr      r1,   =CONFIG_SYS_GRER2_VAL
-   str      r1,   [r0]
-
-   /* General falling edge registers */
-   ldr      r0,   =GFER0
-   ldr      r1,   =CONFIG_SYS_GFER0_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GFER1
-   ldr      r1,   =CONFIG_SYS_GFER1_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GFER2
-   ldr      r1,   =CONFIG_SYS_GFER2_VAL
-   str      r1,   [r0]
-
-   /* General edge detect registers */
-   ldr      r0,   =GPDR0
-   ldr      r1,   =CONFIG_SYS_GPDR0_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GPDR1
-   ldr      r1,   =CONFIG_SYS_GPDR1_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GPDR2
-   ldr      r1,   =CONFIG_SYS_GPDR2_VAL
-   str      r1,   [r0]
-
-   /* General alternate function registers */
-   ldr      r0,   =GAFR0_L		/* [0:15] */
-   ldr      r1,   =CONFIG_SYS_GAFR0_L_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GAFR0_U		/* [31:16] */
-   ldr      r1,   =CONFIG_SYS_GAFR0_U_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GAFR1_L		/* [47:32] */
-   ldr      r1,   =CONFIG_SYS_GAFR1_L_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GAFR1_U		/* [63:48] */
-   ldr      r1,   =CONFIG_SYS_GAFR1_U_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GAFR2_L		/* [79:64] */
-   ldr      r1,   =CONFIG_SYS_GAFR2_L_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GAFR2_U		/* [80] */
-   ldr      r1,   =CONFIG_SYS_GAFR2_U_VAL
-   str      r1,   [r0]
-
-   /* General purpose direction registers */
-   ldr      r0,   =GPDR0
-   ldr      r1,   =CONFIG_SYS_GPDR0_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GPDR1
-   ldr      r1,   =CONFIG_SYS_GPDR1_VAL
-   str      r1,   [r0]
-   ldr      r0,   =GPDR2
-   ldr      r1,   =CONFIG_SYS_GPDR2_VAL
-   str      r1,   [r0]
-
-   /* Power manager sleep status */
-   ldr      r0,   =PSSR
-   ldr      r1,   =CONFIG_SYS_PSSR_VAL
-   str      r1,   [r0]
-
-/* ---- MEMORY INITIALISATION ---- */
-/* Initialize Memory Controller, see PXA250 Operating System Developer's Guide */
-/* pause for 200 uSecs- allow internal clocks to settle */
-   ldr r3, =OSCR	/* reset the OS Timer Count to zero */
-   mov r2, #0
-   str r2, [r3]
-   ldr r4, =0x300	/* really 0x2E1 is about 200usec, so 0x300 should be plenty */
-1:
-   ldr r2, [r3]
-   cmp r4, r2
-   bgt 1b
-
-mem_init:
-/* get memory controller base address */
-   ldr     r1,  =MEMC_BASE
-
-/* ---- FLASH INITIALISATION ---- */
-/* Write MSC0 and read back to ensure data change is accepted by cpu */
-   ldr     r2,   =CONFIG_SYS_MSC0_VAL
-   str     r2,   [r1, #MSC0_OFFSET]
-   ldr     r2,   [r1, #MSC0_OFFSET]
-
-/* ---- SDRAM INITIALISATION ---- */
-/* get the MDREFR settings */
-   ldr     r2,  =CONFIG_SYS_MDREFR_VAL
-   str     r2,  [r1, #MDREFR_OFFSET]
-
-/* fetch platform value of MDCNFG */
-   ldr     r2,  =CONFIG_SYS_MDCNFG_VAL
-
-/* disable all sdram banks */
-   bic     r2,  r2,  #(MDCNFG_DE0 | MDCNFG_DE1)
-   bic     r2,  r2,  #(MDCNFG_DE2 | MDCNFG_DE3)
-
-/* write initial value of MDCNFG, w/o enabling sdram banks */
-   str     r2,  [r1, #MDCNFG_OFFSET]
-
-/* pause for 200 uSecs */
-   ldr r3, =OSCR	/* reset the OS Timer Count to zero */
-   mov r2, #0
-   str r2, [r3]
-   ldr r4, =0x300	/* about 200 usec */
-1:
-   ldr r2, [r3]
-   cmp r4, r2
-   bgt 1b
-
-/* Access memory *not yet enabled* for CBR refresh cycles (8) */
-/* CBR is generated for all banks */
-
-   ldr     r2, =CONFIG_SYS_DRAM_BASE
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-   str     r2, [r2]
-
-/* get memory controller base address */
-   ldr     r2,  =MEMC_BASE
-
-/* Enable SDRAM bank 0 in MDCNFG register */
-   ldr     r2,  [r1, #MDCNFG_OFFSET]
-   orr     r2,  r2,  #MDCNFG_DE0
-   str     r2,  [r1, #MDCNFG_OFFSET]
-
-/* write MDMRS to trigger an MSR command to all enabled SDRAM banks */
-   ldr     r2,  =CONFIG_SYS_MDMRS_VAL
-   str     r2,  [r1, #MDMRS_OFFSET]
-
-/* ---- INTERRUPT INITIALISATION ---- */
-/* Disable (mask) all interrupts at the interrupt controller */
-/* clear the interrupt level register (use IRQ, not FIQ) */
-   mov     r1, #0
-   ldr     r2,  =ICLR
-   str     r1,  [r2]
-
-/* Set interrupt mask register */
-   ldr     r1,  =CONFIG_SYS_ICMR_VAL
-   ldr     r2,  =ICMR
-   str     r1,  [r2]
-
-/* ---- CLOCK INITIALISATION ---- */
-/* Disable the peripheral clocks, and set the core clock */
-
-/* Turn Off ALL on-chip peripheral clocks for re-configuration */
-   ldr     r1,  =CKEN
-   mov     r2,  #0
-   str     r2,  [r1]
-
-/* set core clocks */
-   ldr     r2,  =CONFIG_SYS_CCCR_VAL
-   ldr     r1,  =CCCR
-   str     r2,  [r1]
-
-#ifdef ENABLE32KHZ
-/* enable the 32Khz oscillator for RTC and PowerManager */
-   ldr     r1,  =OSCC
-   mov     r2,  #OSCC_OON
-   str     r2,  [r1]
-
-/* NOTE:  spin here until OSCC.OOK get set, meaning the PLL has settled. */
-60:
-   ldr     r2, [r1]
-   ands    r2, r2, #1
-   beq     60b
-#endif
-
-/* Turn on needed clocks */
-   ldr     r1,  =CKEN
-   ldr     r2,  =CONFIG_SYS_CKEN_VAL
-   str     r2,  [r1]
-
-   mov   pc, r10
diff --git a/board/xsengine/xsengine.c b/board/xsengine/xsengine.c
deleted file mode 100644
index 4464fd4..0000000
--- a/board/xsengine/xsengine.c
+++ /dev/null
@@ -1,75 +0,0 @@
-/*
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Miscelaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
-	/* memory and cpu-speed are setup before relocation */
-	/* so we do _nothing_ here */
-
-	/* arch number */
-	gd->bd->bi_arch_number = MACH_TYPE_XSENGINE;
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0xa0000100;
-
-	return 0;
-}
-
-int board_late_init (void)
-{
-	setenv ("stdout", "serial");
-	setenv ("stderr", "serial");
-	return 0;
-}
-
-int dram_init (void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_SMC91111
-	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
-	return rc;
-}
-#endif
diff --git a/boards.cfg b/boards.cfg
index 0f3292f..4efbff8 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -65,7 +65,6 @@ balloon3	arm	pxa
 cerf250		arm	pxa
 cradle		arm	pxa
 csb226		arm	pxa
-delta		arm	pxa
 innokom		arm	pxa
 lubbock		arm	pxa
 palmld		arm	pxa
@@ -402,8 +401,6 @@ lpd7a400	arm	lh7a40x		lpd7a40x
 lpd7a404	arm	lh7a40x		lpd7a40x
 colibri_pxa270	arm	pxa
 pxa255_idp	arm	pxa
-wepep250	arm	pxa
-xsengine	arm	pxa
 zylonite	arm	pxa
 atngw100	avr32	at32ap		-		atmel		at32ap700x
 atstk1002	avr32	at32ap		atstk1000	atmel		at32ap700x
@@ -556,8 +553,9 @@ MPC8540ADS	powerpc	mpc85xx		mpc8540ads	freescale
 MPC8544DS	powerpc	mpc85xx		mpc8544ds	freescale
 MPC8560ADS	powerpc	mpc85xx		mpc8560ads	freescale
 MPC8568MDS	powerpc	mpc85xx		mpc8568mds	freescale
-XPEDITE5200	powerpc	mpc85xx		xpedite5200	xes
-XPEDITE5370	powerpc	mpc85xx		xpedite5370	xes
+xpedite520x	powerpc	mpc85xx		-		xes
+xpedite537x	powerpc	mpc85xx		-		xes
+xpedite550x	powerpc	mpc85xx		-		xes
 sbc8540_33	powerpc	mpc85xx		sbc8560		-		-	SBC8540
 sbc8540_66	powerpc	mpc85xx		sbc8560		-		-	SBC8540
 sbc8548_PCI_33	powerpc	mpc85xx		sbc8548		-		-	sbc8548:PCI,33
@@ -597,7 +595,7 @@ P2020RDB_NAND	powerpc	mpc85xx		p1_p2_rdb	freescale	-	P1_P2_RDB:P2020,NAND
 P2020RDB_SDCARD	powerpc	mpc85xx		p1_p2_rdb	freescale	-	P1_P2_RDB:P2020,SDCARD
 sbc8641d	powerpc	mpc86xx
 MPC8610HPCD	powerpc	mpc86xx		mpc8610hpcd	freescale
-XPEDITE5170	powerpc	mpc86xx		xpedite5170	xes
+xpedite517x	powerpc	mpc86xx		-		xes
 MPC8641HPCN	powerpc	mpc86xx		mpc8641hpcn	freescale	-	MPC8641HPCN
 cogent_mpc8xx	powerpc	mpc8xx		cogent
 ESTEEM192E	powerpc	mpc8xx		esteem192e
@@ -648,7 +646,7 @@ CPCIISER4	powerpc	ppc4xx		cpciiser4	esd
 DASA_SIM	powerpc	ppc4xx		dasa_sim	esd
 PMC405DE	powerpc	ppc4xx		pmc405de	esd
 METROBOX	powerpc	ppc4xx		metrobox	sandburst
-XPEDITE1000	powerpc	ppc4xx		xpedite1000	xes
+xpedite1000	powerpc	ppc4xx		-		xes
 korat_perm	powerpc	ppc4xx		korat		-		-	korat:KORAT_PERMANENT
 haleakala	powerpc	ppc4xx		kilauea		amcc		-	kilauea:HALEAKALA
 sycamore	powerpc	ppc4xx		walnut		amcc		-	walnut
@@ -732,5 +730,18 @@ davinci_dm6467evm arm	arm926ejs	dm6467evm	davinci		davinci
 davinci_schmoogie arm	arm926ejs	schmoogie	davinci		davinci
 davinci_dm355leopard arm arm926ejs	dm355leopard	davinci		davinci
 bf527-ad7160-eval blackfin	blackfin
+rsk7203	sh	sh2		rsk7203		renesas		-
+mpr2	sh	sh3		mpr2	-	-
+ms7720se	sh	sh3	ms7720se	-	-
+MigoRsh	sh4	MigoR	renesas	-   
+ms7750se	sh	sh4	ms7750se	-	-   
+ms7722se	sh	sh4	ms7722se	-	-   
+r2dplus	sh	sh4	r2dplus	renesas	-   
+r7780mp	sh	sh4	r7780mp	renesas	-   
+sh7763rdp	sh	sh4	sh7763rdp	renesas	-   
+sh7785lcr	sh	sh4	sh7785lcr	renesas	-   
+sh7785lcr_32bit	sh  sh4	sh7785lcr	renesas	-	sh7785lcr:SH_32BIT=1
+ap325rxa	sh	sh4	ap325rxa	renesas	-   
+espt	sh	sh4	espt	-	-
 # Target	ARCH	CPU		Board name	Vendor		SoC		Options
 ###############################################################################################
diff --git a/common/cmd_onenand.c b/common/cmd_onenand.c
index 83d967b..fe84c3b 100644
--- a/common/cmd_onenand.c
+++ b/common/cmd_onenand.c
@@ -525,6 +525,12 @@ static cmd_tbl_t cmd_onenand_sub[] = {
 	U_BOOT_CMD_MKENT(markbad, CONFIG_SYS_MAXARGS, 0, do_onenand_markbad, "", ""),
 };
 
+#ifndef CONFIG_RELOC_FIXUP_WORKS
+void onenand_reloc(void) {
+	fixup_cmdtable(cmd_onenand_sub, ARRAY_SIZE(cmd_onenand_sub));
+}
+#endif
+
 static int do_onenand(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
 {
 	cmd_tbl_t *c;
diff --git a/common/cmd_pci.c b/common/cmd_pci.c
index 4bde059..ccf5ada 100644
--- a/common/cmd_pci.c
+++ b/common/cmd_pci.c
@@ -497,6 +497,10 @@ int do_pci (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 		if ((bdf = get_pci_dev(argv[2])) == -1)
 			return 1;
 		break;
+#ifdef CONFIG_CMD_PCI_ENUM
+	case 'e':
+		break;
+#endif
 	default:		/* scan bus */
 		value = 1; /* short listing */
 		bdf = 0;   /* bus number  */
@@ -518,6 +522,11 @@ int do_pci (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 		return 0;
 	case 'd':		/* display */
 		return pci_cfg_display(bdf, addr, size, value);
+#ifdef CONFIG_CMD_PCI_ENUM
+	case 'e':
+		pci_init();
+		return 0;
+#endif
 	case 'n':		/* next */
 		if (argc < 4)
 			goto usage;
@@ -545,6 +554,10 @@ U_BOOT_CMD(
 	"list and access PCI Configuration Space",
 	"[bus] [long]\n"
 	"    - short or long list of PCI devices on bus 'bus'\n"
+#ifdef CONFIG_CMD_PCI_ENUM
+	"pci enum\n"
+	"    - re-enumerate PCI buses\n"
+#endif
 	"pci header b.d.f\n"
 	"    - show header of PCI device 'bus.device.function'\n"
 	"pci display[.b, .w, .l] b.d.f [address] [# of objects]\n"
diff --git a/common/env_flash.c b/common/env_flash.c
index 1da78b7..54c0bfe 100644
--- a/common/env_flash.c
+++ b/common/env_flash.c
@@ -82,9 +82,6 @@ uchar env_get_char_spec(int index)
 	return (*((uchar *)(gd->env_addr + index)));
 }
 
-#undef debug
-#define debug printf
-
 #ifdef CONFIG_ENV_ADDR_REDUND
 
 int  env_init(void)
diff --git a/common/hwconfig.c b/common/hwconfig.c
index 1f9f4a0..3c9759f 100644
--- a/common/hwconfig.c
+++ b/common/hwconfig.c
@@ -26,6 +26,8 @@
 #define min(a, b) (((a) < (b)) ? (a) : (b))
 #endif /* HWCONFIG_TEST */
 
+DECLARE_GLOBAL_DATA_PTR;
+
 static const char *hwconfig_parse(const char *opts, size_t maxlen,
 				  const char *opt, char *stopchs, char eqch,
 				  size_t *arglen)
@@ -69,9 +71,26 @@ next:
 const char *cpu_hwconfig __attribute__((weak));
 const char *board_hwconfig __attribute__((weak));
 
+#define HWCONFIG_PRE_RELOC_BUF_SIZE	128
+
 static const char *__hwconfig(const char *opt, size_t *arglen)
 {
-	const char *env_hwconfig = getenv("hwconfig");
+	const char *env_hwconfig = NULL;
+	char buf[HWCONFIG_PRE_RELOC_BUF_SIZE];
+
+	if (gd->flags & GD_FLG_ENV_READY) {
+		env_hwconfig = getenv("hwconfig");
+	} else {
+		/*
+		 * Use our own on stack based buffer before relocation to allow
+		 * accessing longer hwconfig strings that might be in the
+		 * environment before we've relocated.  This is pretty fragile
+		 * on both the use of stack and if the buffer is big enough.
+		 * However we will get a warning from getenv_f for the later.
+		 */
+		if ((getenv_f("hwconfig", buf, sizeof(buf))) > 0)
+			env_hwconfig = buf;
+	}
 
 	if (env_hwconfig)
 		return hwconfig_parse(env_hwconfig, strlen(env_hwconfig),
diff --git a/common/usb_storage.c b/common/usb_storage.c
index 613c4f0..1e6cd6a 100644
--- a/common/usb_storage.c
+++ b/common/usb_storage.c
@@ -70,7 +70,7 @@
 /* direction table -- this indicates the direction of the data
  * transfer for each command code -- a 1 indicates input
  */
-unsigned char us_direction[256/8] = {
+static const unsigned char us_direction[256/8] = {
 	0x28, 0x81, 0x14, 0x14, 0x20, 0x01, 0x90, 0x77,
 	0x0C, 0x20, 0x00, 0x04, 0x00, 0x00, 0x00, 0x00,
 	0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x01,
diff --git a/doc/README.LED_display b/doc/README.LED_display
index 521746e..19977ea 100644
--- a/doc/README.LED_display
+++ b/doc/README.LED_display
@@ -14,7 +14,6 @@ This function should control the state of the LED display. Argument is
 an ORed combination of the following values:
  DISPLAY_CLEAR	-- clear the display
  DISPLAY_HOME	-- set the position to the beginning of display
- DISPLAY_MARK	-- enable mark (decimal point), if implemented
 
 int display_putc(char c);
 
diff --git a/doc/README.POST b/doc/README.POST
index eeb218d..6815d49 100644
--- a/doc/README.POST
+++ b/doc/README.POST
@@ -659,12 +659,19 @@ not need any modifications for porting them to another board/CPU.
 2.2.2.1. I2C test
 
 For verifying the I2C bus, a full I2C bus scanning will be performed
-using the i2c_probe() routine. If any I2C device is found, the test
-will be considered as passed, otherwise failed. This particular way
-will be used because it provides the most common method of testing.
-For example, using the internal loopback mode of the CPM I2C
-controller for testing would not work on boards where the software
-I2C driver (also known as bit-banged driver) is used.
+using the i2c_probe() routine. If a board defines
+CONFIG_SYS_POST_I2C_ADDRS the I2C test will pass if all devices
+listed in CONFIG_SYS_POST_I2C_ADDRS are found, and no additional
+devices are detected.  If CONFIG_SYS_POST_I2C_ADDRS is not defined
+the test will pass if any I2C device is found.
+
+The CONFIG_SYS_POST_I2C_IGNORES define can be used to list I2C
+devices which may or may not be present when using
+CONFIG_SYS_POST_I2C_ADDRS.  The I2C POST test will pass regardless
+if the devices in CONFIG_SYS_POST_I2C_IGNORES are found or not.
+This is useful in cases when I2C devices are optional (eg on a
+daughtercard that may or may not be present) or not critical
+to board operation.
 
 2.2.2.2. Watchdog timer test
 
diff --git a/drivers/mtd/cfi_flash.c b/drivers/mtd/cfi_flash.c
index 798902f..c92c7a7 100644
--- a/drivers/mtd/cfi_flash.c
+++ b/drivers/mtd/cfi_flash.c
@@ -85,6 +85,17 @@ static phys_addr_t __cfi_flash_bank_addr(int i)
 phys_addr_t cfi_flash_bank_addr(int i)
 	__attribute__((weak, alias("__cfi_flash_bank_addr")));
 
+static unsigned long __cfi_flash_bank_size(int i)
+{
+#ifdef CONFIG_SYS_FLASH_BANKS_SIZES
+	return ((unsigned long [])CONFIG_SYS_FLASH_BANKS_SIZES)[i];
+#else
+	return 0;
+#endif
+}
+unsigned long cfi_flash_bank_size(int i)
+	__attribute__((weak, alias("__cfi_flash_bank_size")));
+
 static void __flash_write8(u8 value, void *addr)
 {
 	__raw_writeb(value, addr);
@@ -1826,7 +1837,7 @@ static void flash_fixup_stm(flash_info_t *info, struct cfi_qry *qry)
  * The following code cannot be run from FLASH!
  *
  */
-ulong flash_get_size (phys_addr_t base, int banknum)
+ulong flash_get_size (phys_addr_t base, int banknum, unsigned long max_size)
 {
 	flash_info_t *info = &flash_info[banknum];
 	int i, j;
@@ -1915,6 +1926,13 @@ ulong flash_get_size (phys_addr_t base, int banknum)
 		debug ("size_ratio %d port %d bits chip %d bits\n",
 		       size_ratio, info->portwidth << CFI_FLASH_SHIFT_WIDTH,
 		       info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
+		info->size = 1 << qry.dev_size;
+		/* multiply the size by the number of chips */
+		info->size *= size_ratio;
+		if (max_size && (info->size > max_size)) {
+			debug("[truncated from %ldMiB]", info->size >> 20);
+			info->size = max_size;
+		}
 		debug ("found %d erase regions\n", num_erase_regions);
 		sect_cnt = 0;
 		sector = base;
@@ -1935,6 +1953,8 @@ ulong flash_get_size (phys_addr_t base, int banknum)
 			debug ("erase_region_count = %d erase_region_size = %d\n",
 				erase_region_count, erase_region_size);
 			for (j = 0; j < erase_region_count; j++) {
+				if (sector - base >= info->size)
+					break;
 				if (sect_cnt >= CONFIG_SYS_MAX_FLASH_SECT) {
 					printf("ERROR: too many flash sectors\n");
 					break;
@@ -1968,9 +1988,6 @@ ulong flash_get_size (phys_addr_t base, int banknum)
 		}
 
 		info->sector_count = sect_cnt;
-		info->size = 1 << qry.dev_size;
-		/* multiply the size by the number of chips */
-		info->size *= size_ratio;
 		info->buffer_size = 1 << le16_to_cpu(qry.max_buf_write_size);
 		tmp = 1 << qry.block_erase_timeout_typ;
 		info->erase_blk_tout = tmp *
@@ -2026,7 +2043,8 @@ unsigned long flash_init (void)
 		flash_info[i].flash_id = FLASH_UNKNOWN;
 
 		if (!flash_detect_legacy(cfi_flash_bank_addr(i), i))
-			flash_get_size(cfi_flash_bank_addr(i), i);
+			flash_get_size(cfi_flash_bank_addr(i), i,
+					cfi_flash_bank_size(i));
 		size += flash_info[i].size;
 		if (flash_info[i].flash_id == FLASH_UNKNOWN) {
 #ifndef CONFIG_SYS_FLASH_QUIET_TEST
diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c
index 001e6eb..1f02103 100644
--- a/drivers/pci/fsl_pci_init.c
+++ b/drivers/pci/fsl_pci_init.c
@@ -91,6 +91,9 @@ int fsl_setup_hose(struct pci_controller *hose, unsigned long addr)
 {
 	volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) addr;
 
+	/* Reset hose to make sure its in a clean state */
+	memset(hose, 0, sizeof(struct pci_controller));
+
 	pci_setup_indirect(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
 
 	return fsl_is_pci_agent(hose);
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index cd64a87..848746f 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -139,7 +139,7 @@ void *pci_map_bar(pci_dev_t pdev, int bar, int flags)
  *
  */
 
-static struct pci_controller* hose_head = NULL;
+static struct pci_controller* hose_head;
 
 void pci_register_hose(struct pci_controller* hose)
 {
@@ -640,6 +640,8 @@ void pci_init(void)
 	}
 #endif /* CONFIG_PCI_BOOTDELAY */
 
+	hose_head = NULL;
+
 	/* now call board specific pci_init()... */
 	pci_init_board();
 }
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index 047902a..cff3438 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -53,6 +53,10 @@ int ehci_hcd_init(void)
 	hcor = (struct ehci_hcor *)((uint32_t) hccr +
 			HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
 
+	debug("EHCI-PCI init hccr 0x%x and hcor 0x%x hc_length %d\n",
+			(uint32_t)hccr, (uint32_t)hcor,
+			(uint32_t)HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
+
 	return 0;
 }
 
diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h
index d3aa55b..945ab64 100644
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -175,7 +175,7 @@ struct qTD {
 	uint32_t qt_buffer_hi[5];	/* Appendix B */
 	/* pad struct for 32 byte alignment */
 	uint32_t unused[3];
-} __attribute__ ((aligned (32)));
+};
 
 /* Queue Head (QH). */
 struct QH {
diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index 6fe2c39..545ebf4 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -76,7 +76,7 @@ void musb_start(void)
  * epinfo	- Pointer to EP configuration table
  * cnt		- Number of entries in the EP conf table.
  */
-void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt)
+void musb_configure_ep(const struct musb_epinfo *epinfo, u8 cnt)
 {
 	u16 csr;
 	u16 fifoaddr = 64; /* First 64 bytes of FIFO reserved for EP0 */
diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h
index 8f73876..a8adcce 100644
--- a/drivers/usb/musb/musb_core.h
+++ b/drivers/usb/musb/musb_core.h
@@ -357,7 +357,7 @@ extern struct musb_regs		*musbr;
 
 /* exported functions */
 extern void musb_start(void);
-extern void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt);
+extern void musb_configure_ep(const struct musb_epinfo *epinfo, u8 cnt);
 extern void write_fifo(u8 ep, u32 length, void *fifo_data);
 extern void read_fifo(u8 ep, u32 length, void *fifo_data);
 
diff --git a/drivers/usb/musb/musb_hcd.c b/drivers/usb/musb/musb_hcd.c
index f38b279..8b0c61d 100644
--- a/drivers/usb/musb/musb_hcd.c
+++ b/drivers/usb/musb/musb_hcd.c
@@ -29,7 +29,7 @@
 #define USB_MSC_BBB_GET_MAX_LUN	0xFE
 
 /* Endpoint configuration information */
-static struct musb_epinfo epinfo[3] = {
+static const struct musb_epinfo epinfo[3] = {
 	{MUSB_BULK_EP, 1, 512}, /* EP1 - Bluk Out - 512 Bytes */
 	{MUSB_BULK_EP, 0, 512}, /* EP1 - Bluk In  - 512 Bytes */
 	{MUSB_INTR_EP, 0, 64}   /* EP2 - Interrupt IN - 64 Bytes */
@@ -41,7 +41,7 @@ static int rh_devnum;
 static u32 port_status;
 
 /* Device descriptor */
-static u8 root_hub_dev_des[] = {
+static const u8 root_hub_dev_des[] = {
 	0x12,			/*  __u8  bLength; */
 	0x01,			/*  __u8  bDescriptorType; Device */
 	0x00,			/*  __u16 bcdUSB; v1.1 */
@@ -63,7 +63,7 @@ static u8 root_hub_dev_des[] = {
 };
 
 /* Configuration descriptor */
-static u8 root_hub_config_des[] = {
+static const u8 root_hub_config_des[] = {
 	0x09,			/*  __u8  bLength; */
 	0x02,			/*  __u8  bDescriptorType; Configuration */
 	0x19,			/*  __u16 wTotalLength; */
@@ -96,14 +96,14 @@ static u8 root_hub_config_des[] = {
 	0xff			/*  __u8  ep_bInterval; 255 ms */
 };
 
-static unsigned char root_hub_str_index0[] = {
+static const unsigned char root_hub_str_index0[] = {
 	0x04,			/*  __u8  bLength; */
 	0x03,			/*  __u8  bDescriptorType; String-descriptor */
 	0x09,			/*  __u8  lang ID */
 	0x04,			/*  __u8  lang ID */
 };
 
-static unsigned char root_hub_str_index1[] = {
+static const unsigned char root_hub_str_index1[] = {
 	0x1c,			/*  __u8  bLength; */
 	0x03,			/*  __u8  bDescriptorType; String-descriptor */
 	'M',			/*  __u8  Unicode */
@@ -557,7 +557,7 @@ static int musb_submit_rh_msg(struct usb_device *dev, unsigned long pipe,
 	int len = 0;
 	int stat = 0;
 	u32 datab[4];
-	u8 *data_buf = (u8 *) datab;
+	const u8 *data_buf = (u8 *) datab;
 	u16 bmRType_bReq;
 	u16 wValue;
 	u16 wIndex;
@@ -778,25 +778,27 @@ static int musb_submit_rh_msg(struct usb_device *dev, unsigned long pipe,
 
 		break;
 
-	case RH_GET_DESCRIPTOR | RH_CLASS:
+	case RH_GET_DESCRIPTOR | RH_CLASS: {
+		u8 *_data_buf = (u8 *) datab;
 		debug("RH_GET_DESCRIPTOR | RH_CLASS\n");
 
-		data_buf[0] = 0x09;	/* min length; */
-		data_buf[1] = 0x29;
-		data_buf[2] = 0x1;	/* 1 port */
-		data_buf[3] = 0x01;	/* per-port power switching */
-		data_buf[3] |= 0x10;	/* no overcurrent reporting */
+		_data_buf[0] = 0x09;	/* min length; */
+		_data_buf[1] = 0x29;
+		_data_buf[2] = 0x1;	/* 1 port */
+		_data_buf[3] = 0x01;	/* per-port power switching */
+		_data_buf[3] |= 0x10;	/* no overcurrent reporting */
 
 		/* Corresponds to data_buf[4-7] */
-		data_buf[4] = 0;
-		data_buf[5] = 5;
-		data_buf[6] = 0;
-		data_buf[7] = 0x02;
-		data_buf[8] = 0xff;
+		_data_buf[4] = 0;
+		_data_buf[5] = 5;
+		_data_buf[6] = 0;
+		_data_buf[7] = 0x02;
+		_data_buf[8] = 0xff;
 
 		len = min_t(unsigned int, leni,
 			    min_t(unsigned int, data_buf[0], wLength));
 		break;
+	}
 
 	case RH_GET_CONFIGURATION:
 		debug("RH_GET_CONFIGURATION\n");
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 4be82e7..5b7b261 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -34,6 +34,7 @@ COBJS-$(CONFIG_VIDEO_CT69000) += ct69000.o videomodes.o
 COBJS-$(CONFIG_VIDEO_MB862xx) += mb862xx.o videomodes.o
 COBJS-$(CONFIG_VIDEO_MB86R0xGDC) += mb86r0xgdc.o videomodes.o
 COBJS-$(CONFIG_VIDEO_MX3) += mx3fb.o
+COBJS-$(CONFIG_VIDEO_MX5) += mxc_ipuv3_fb.o ipu_common.o ipu_disp.o
 COBJS-$(CONFIG_VIDEO_SED13806) += sed13806.o
 COBJS-$(CONFIG_SED156X) += sed156x.o
 COBJS-$(CONFIG_VIDEO_SM501) += sm501.o
diff --git a/drivers/video/ipu.h b/drivers/video/ipu.h
new file mode 100644
index 0000000..d8bc287
--- /dev/null
+++ b/drivers/video/ipu.h
@@ -0,0 +1,321 @@
+/*
+ * Porting to u-boot:
+ *
+ * (C) Copyright 2010
+ * Stefano Babic, DENX Software Engineering, sbabic@denx.de
+ *
+ * Linux IPU driver for MX51:
+ *
+ * (C) Copyright 2005-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ASM_ARCH_IPU_H__
+#define __ASM_ARCH_IPU_H__
+
+#include <linux/types.h>
+
+#define IDMA_CHAN_INVALID	0xFF
+#define HIGH_RESOLUTION_WIDTH	1024
+
+struct clk {
+	const char *name;
+	int id;
+	/* Source clock this clk depends on */
+	struct clk *parent;
+	/* Secondary clock to enable/disable with this clock */
+	struct clk *secondary;
+	/* Current clock rate */
+	unsigned long rate;
+	/* Reference count of clock enable/disable */
+	__s8 usecount;
+	/* Register bit position for clock's enable/disable control. */
+	u8 enable_shift;
+	/* Register address for clock's enable/disable control. */
+	void *enable_reg;
+	u32 flags;
+	/*
+	 * Function ptr to recalculate the clock's rate based on parent
+	 * clock's rate
+	 */
+	void (*recalc) (struct clk *);
+	/*
+	 * Function ptr to set the clock to a new rate. The rate must match a
+	 * supported rate returned from round_rate. Leave blank if clock is not
+	* programmable
+	 */
+	int (*set_rate) (struct clk *, unsigned long);
+	/*
+	 * Function ptr to round the requested clock rate to the nearest
+	 * supported rate that is less than or equal to the requested rate.
+	 */
+	unsigned long (*round_rate) (struct clk *, unsigned long);
+	/*
+	 * Function ptr to enable the clock. Leave blank if clock can not
+	 * be gated.
+	 */
+	int (*enable) (struct clk *);
+	/*
+	 * Function ptr to disable the clock. Leave blank if clock can not
+	 * be gated.
+	 */
+	void (*disable) (struct clk *);
+	/* Function ptr to set the parent clock of the clock. */
+	int (*set_parent) (struct clk *, struct clk *);
+};
+
+/*
+ * Enumeration of Synchronous (Memory-less) panel types
+ */
+typedef enum {
+	IPU_PANEL_SHARP_TFT,
+	IPU_PANEL_TFT,
+} ipu_panel_t;
+
+/*  IPU Pixel format definitions */
+#define fourcc(a, b, c, d)\
+	(((__u32)(a)<<0)|((__u32)(b)<<8)|((__u32)(c)<<16)|((__u32)(d)<<24))
+
+/*
+ * Pixel formats are defined with ASCII FOURCC code. The pixel format codes are
+ * the same used by V4L2 API.
+ */
+
+#define IPU_PIX_FMT_GENERIC fourcc('I', 'P', 'U', '0')
+#define IPU_PIX_FMT_GENERIC_32 fourcc('I', 'P', 'U', '1')
+#define IPU_PIX_FMT_LVDS666 fourcc('L', 'V', 'D', '6')
+#define IPU_PIX_FMT_LVDS888 fourcc('L', 'V', 'D', '8')
+
+#define IPU_PIX_FMT_RGB332  fourcc('R', 'G', 'B', '1')	/*<  8  RGB-3-3-2    */
+#define IPU_PIX_FMT_RGB555  fourcc('R', 'G', 'B', 'O')	/*< 16  RGB-5-5-5    */
+#define IPU_PIX_FMT_RGB565  fourcc('R', 'G', 'B', 'P')	/*< 1 6  RGB-5-6-5   */
+#define IPU_PIX_FMT_RGB666  fourcc('R', 'G', 'B', '6')	/*< 18  RGB-6-6-6    */
+#define IPU_PIX_FMT_BGR666  fourcc('B', 'G', 'R', '6')	/*< 18  BGR-6-6-6    */
+#define IPU_PIX_FMT_BGR24   fourcc('B', 'G', 'R', '3')	/*< 24  BGR-8-8-8    */
+#define IPU_PIX_FMT_RGB24   fourcc('R', 'G', 'B', '3')	/*< 24  RGB-8-8-8    */
+#define IPU_PIX_FMT_BGR32   fourcc('B', 'G', 'R', '4')	/*< 32  BGR-8-8-8-8  */
+#define IPU_PIX_FMT_BGRA32  fourcc('B', 'G', 'R', 'A')	/*< 32  BGR-8-8-8-8  */
+#define IPU_PIX_FMT_RGB32   fourcc('R', 'G', 'B', '4')	/*< 32  RGB-8-8-8-8  */
+#define IPU_PIX_FMT_RGBA32  fourcc('R', 'G', 'B', 'A')	/*< 32  RGB-8-8-8-8  */
+#define IPU_PIX_FMT_ABGR32  fourcc('A', 'B', 'G', 'R')	/*< 32  ABGR-8-8-8-8 */
+
+/* YUV Interleaved Formats */
+#define IPU_PIX_FMT_YUYV    fourcc('Y', 'U', 'Y', 'V')	/*< 16 YUV 4:2:2 */
+#define IPU_PIX_FMT_UYVY    fourcc('U', 'Y', 'V', 'Y')	/*< 16 YUV 4:2:2 */
+#define IPU_PIX_FMT_Y41P    fourcc('Y', '4', '1', 'P')	/*< 12 YUV 4:1:1 */
+#define IPU_PIX_FMT_YUV444  fourcc('Y', '4', '4', '4')	/*< 24 YUV 4:4:4 */
+
+/* two planes -- one Y, one Cb + Cr interleaved  */
+#define IPU_PIX_FMT_NV12    fourcc('N', 'V', '1', '2') /* 12  Y/CbCr 4:2:0  */
+
+#define IPU_PIX_FMT_GREY    fourcc('G', 'R', 'E', 'Y')	/*< 8  Greyscale */
+#define IPU_PIX_FMT_YVU410P fourcc('Y', 'V', 'U', '9')	/*< 9  YVU 4:1:0 */
+#define IPU_PIX_FMT_YUV410P fourcc('Y', 'U', 'V', '9')	/*< 9  YUV 4:1:0 */
+#define IPU_PIX_FMT_YVU420P fourcc('Y', 'V', '1', '2')	/*< 12 YVU 4:2:0 */
+#define IPU_PIX_FMT_YUV420P fourcc('I', '4', '2', '0')	/*< 12 YUV 4:2:0 */
+#define IPU_PIX_FMT_YUV420P2 fourcc('Y', 'U', '1', '2')	/*< 12 YUV 4:2:0 */
+#define IPU_PIX_FMT_YVU422P fourcc('Y', 'V', '1', '6')	/*< 16 YVU 4:2:2 */
+#define IPU_PIX_FMT_YUV422P fourcc('4', '2', '2', 'P')	/*< 16 YUV 4:2:2 */
+
+/*
+ * IPU Driver channels definitions.
+ * Note these are different from IDMA channels
+ */
+#define IPU_MAX_CH	32
+#define _MAKE_CHAN(num, v_in, g_in, a_in, out) \
+	((num << 24) | (v_in << 18) | (g_in << 12) | (a_in << 6) | out)
+#define _MAKE_ALT_CHAN(ch)		(ch | (IPU_MAX_CH << 24))
+#define IPU_CHAN_ID(ch)			(ch >> 24)
+#define IPU_CHAN_ALT(ch)		(ch & 0x02000000)
+#define IPU_CHAN_ALPHA_IN_DMA(ch)	((uint32_t) (ch >> 6) & 0x3F)
+#define IPU_CHAN_GRAPH_IN_DMA(ch)	((uint32_t) (ch >> 12) & 0x3F)
+#define IPU_CHAN_VIDEO_IN_DMA(ch)	((uint32_t) (ch >> 18) & 0x3F)
+#define IPU_CHAN_OUT_DMA(ch)		((uint32_t) (ch & 0x3F))
+#define NO_DMA 0x3F
+#define ALT	1
+
+/*
+ * Enumeration of IPU logical channels. An IPU logical channel is defined as a
+ * combination of an input (memory to IPU), output (IPU to memory), and/or
+ * secondary input IDMA channels and in some cases an Image Converter task.
+ * Some channels consist of only an input or output.
+ */
+typedef enum {
+	CHAN_NONE = -1,
+
+	MEM_DC_SYNC = _MAKE_CHAN(7, 28, NO_DMA, NO_DMA, NO_DMA),
+	MEM_DC_ASYNC = _MAKE_CHAN(8, 41, NO_DMA, NO_DMA, NO_DMA),
+	MEM_BG_SYNC = _MAKE_CHAN(9, 23, NO_DMA, 51, NO_DMA),
+	MEM_FG_SYNC = _MAKE_CHAN(10, 27, NO_DMA, 31, NO_DMA),
+
+	MEM_BG_ASYNC0 = _MAKE_CHAN(11, 24, NO_DMA, 52, NO_DMA),
+	MEM_FG_ASYNC0 = _MAKE_CHAN(12, 29, NO_DMA, 33, NO_DMA),
+	MEM_BG_ASYNC1 = _MAKE_ALT_CHAN(MEM_BG_ASYNC0),
+	MEM_FG_ASYNC1 = _MAKE_ALT_CHAN(MEM_FG_ASYNC0),
+
+	DIRECT_ASYNC0 = _MAKE_CHAN(13, NO_DMA, NO_DMA, NO_DMA, NO_DMA),
+	DIRECT_ASYNC1 = _MAKE_CHAN(14, NO_DMA, NO_DMA, NO_DMA, NO_DMA),
+
+} ipu_channel_t;
+
+/*
+ * Enumeration of types of buffers for a logical channel.
+ */
+typedef enum {
+	IPU_OUTPUT_BUFFER = 0,	/*< Buffer for output from IPU */
+	IPU_ALPHA_IN_BUFFER = 1,	/*< Buffer for input to IPU */
+	IPU_GRAPH_IN_BUFFER = 2,	/*< Buffer for input to IPU */
+	IPU_VIDEO_IN_BUFFER = 3,	/*< Buffer for input to IPU */
+	IPU_INPUT_BUFFER = IPU_VIDEO_IN_BUFFER,
+	IPU_SEC_INPUT_BUFFER = IPU_GRAPH_IN_BUFFER,
+} ipu_buffer_t;
+
+#define IPU_PANEL_SERIAL		1
+#define IPU_PANEL_PARALLEL		2
+
+struct ipu_channel {
+	u8 video_in_dma;
+	u8 alpha_in_dma;
+	u8 graph_in_dma;
+	u8 out_dma;
+};
+
+enum ipu_dmfc_type {
+	DMFC_NORMAL = 0,
+	DMFC_HIGH_RESOLUTION_DC,
+	DMFC_HIGH_RESOLUTION_DP,
+	DMFC_HIGH_RESOLUTION_ONLY_DP,
+};
+
+
+/*
+ * Union of initialization parameters for a logical channel.
+ */
+typedef union {
+	struct {
+		uint32_t di;
+		unsigned char interlaced;
+	} mem_dc_sync;
+	struct {
+		uint32_t temp;
+	} mem_sdc_fg;
+	struct {
+		uint32_t di;
+		unsigned char interlaced;
+		uint32_t in_pixel_fmt;
+		uint32_t out_pixel_fmt;
+		unsigned char alpha_chan_en;
+	} mem_dp_bg_sync;
+	struct {
+		uint32_t temp;
+	} mem_sdc_bg;
+	struct {
+		uint32_t di;
+		unsigned char interlaced;
+		uint32_t in_pixel_fmt;
+		uint32_t out_pixel_fmt;
+		unsigned char alpha_chan_en;
+	} mem_dp_fg_sync;
+} ipu_channel_params_t;
+
+/*
+ * Bitfield of Display Interface signal polarities.
+ */
+typedef struct {
+	unsigned datamask_en:1;
+	unsigned ext_clk:1;
+	unsigned interlaced:1;
+	unsigned odd_field_first:1;
+	unsigned clksel_en:1;
+	unsigned clkidle_en:1;
+	unsigned data_pol:1;	/* true = inverted */
+	unsigned clk_pol:1;	/* true = rising edge */
+	unsigned enable_pol:1;
+	unsigned Hsync_pol:1;	/* true = active high */
+	unsigned Vsync_pol:1;
+} ipu_di_signal_cfg_t;
+
+typedef enum {
+	RGB,
+	YCbCr,
+	YUV
+} ipu_color_space_t;
+
+/* Common IPU API */
+int32_t ipu_init_channel(ipu_channel_t channel, ipu_channel_params_t *params);
+void ipu_uninit_channel(ipu_channel_t channel);
+
+int32_t ipu_init_channel_buffer(ipu_channel_t channel, ipu_buffer_t type,
+				uint32_t pixel_fmt,
+				uint16_t width, uint16_t height,
+				uint32_t stride,
+				dma_addr_t phyaddr_0, dma_addr_t phyaddr_1,
+				uint32_t u_offset, uint32_t v_offset);
+
+int32_t ipu_update_channel_buffer(ipu_channel_t channel, ipu_buffer_t type,
+				  uint32_t bufNum, dma_addr_t phyaddr);
+
+int32_t ipu_is_channel_busy(ipu_channel_t channel);
+void ipu_clear_buffer_ready(ipu_channel_t channel, ipu_buffer_t type,
+		uint32_t bufNum);
+int32_t ipu_enable_channel(ipu_channel_t channel);
+int32_t ipu_disable_channel(ipu_channel_t channel);
+
+int32_t ipu_init_sync_panel(int disp,
+			    uint32_t pixel_clk,
+			    uint16_t width, uint16_t height,
+			    uint32_t pixel_fmt,
+			    uint16_t h_start_width, uint16_t h_sync_width,
+			    uint16_t h_end_width, uint16_t v_start_width,
+			    uint16_t v_sync_width, uint16_t v_end_width,
+			    uint32_t v_to_h_sync, ipu_di_signal_cfg_t sig);
+
+int32_t ipu_disp_set_global_alpha(ipu_channel_t channel, unsigned char enable,
+				  uint8_t alpha);
+int32_t ipu_disp_set_color_key(ipu_channel_t channel, unsigned char enable,
+			       uint32_t colorKey);
+
+uint32_t bytes_per_pixel(uint32_t fmt);
+
+void clk_enable(struct clk *clk);
+void clk_disable(struct clk *clk);
+u32 clk_get_rate(struct clk *clk);
+int clk_set_rate(struct clk *clk, unsigned long rate);
+long clk_round_rate(struct clk *clk, unsigned long rate);
+int clk_set_parent(struct clk *clk, struct clk *parent);
+int clk_get_usecount(struct clk *clk);
+struct clk *clk_get_parent(struct clk *clk);
+
+void ipu_dump_registers(void);
+int ipu_probe(void);
+
+void ipu_dmfc_init(int dmfc_type, int first);
+void ipu_init_dc_mappings(void);
+void ipu_dmfc_set_wait4eot(int dma_chan, int width);
+void ipu_dc_init(int dc_chan, int di, unsigned char interlaced);
+void ipu_dc_uninit(int dc_chan);
+void ipu_dp_dc_enable(ipu_channel_t channel);
+int ipu_dp_init(ipu_channel_t channel, uint32_t in_pixel_fmt,
+		 uint32_t out_pixel_fmt);
+void ipu_dp_uninit(ipu_channel_t channel);
+void ipu_dp_dc_disable(ipu_channel_t channel, unsigned char swap);
+ipu_color_space_t format_to_colorspace(uint32_t fmt);
+
+#endif
diff --git a/drivers/video/ipu_common.c b/drivers/video/ipu_common.c
new file mode 100644
index 0000000..9d20c86
--- /dev/null
+++ b/drivers/video/ipu_common.c
@@ -0,0 +1,1183 @@
+/*
+ * Porting to u-boot:
+ *
+ * (C) Copyright 2010
+ * Stefano Babic, DENX Software Engineering, sbabic@denx.de
+ *
+ * Linux IPU driver for MX51:
+ *
+ * (C) Copyright 2005-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* #define DEBUG */
+#include <common.h>
+#include <linux/types.h>
+#include <linux/err.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include "ipu.h"
+#include "ipu_regs.h"
+
+extern struct mxc_ccm_reg *mxc_ccm;
+extern u32 *ipu_cpmem_base;
+
+struct ipu_ch_param_word {
+	uint32_t data[5];
+	uint32_t res[3];
+};
+
+struct ipu_ch_param {
+	struct ipu_ch_param_word word[2];
+};
+
+#define ipu_ch_param_addr(ch) (((struct ipu_ch_param *)ipu_cpmem_base) + (ch))
+
+#define _param_word(base, w) \
+	(((struct ipu_ch_param *)(base))->word[(w)].data)
+
+#define ipu_ch_param_set_field(base, w, bit, size, v) { \
+	int i = (bit) / 32; \
+	int off = (bit) % 32; \
+	_param_word(base, w)[i] |= (v) << off; \
+	if (((bit) + (size) - 1) / 32 > i) { \
+		_param_word(base, w)[i + 1] |= (v) >> (off ? (32 - off) : 0); \
+	} \
+}
+
+#define ipu_ch_param_mod_field(base, w, bit, size, v) { \
+	int i = (bit) / 32; \
+	int off = (bit) % 32; \
+	u32 mask = (1UL << size) - 1; \
+	u32 temp = _param_word(base, w)[i]; \
+	temp &= ~(mask << off); \
+	_param_word(base, w)[i] = temp | (v) << off; \
+	if (((bit) + (size) - 1) / 32 > i) { \
+		temp = _param_word(base, w)[i + 1]; \
+		temp &= ~(mask >> (32 - off)); \
+		_param_word(base, w)[i + 1] = \
+			temp | ((v) >> (off ? (32 - off) : 0)); \
+	} \
+}
+
+#define ipu_ch_param_read_field(base, w, bit, size) ({ \
+	u32 temp2; \
+	int i = (bit) / 32; \
+	int off = (bit) % 32; \
+	u32 mask = (1UL << size) - 1; \
+	u32 temp1 = _param_word(base, w)[i]; \
+	temp1 = mask & (temp1 >> off); \
+	if (((bit)+(size) - 1) / 32 > i) { \
+		temp2 = _param_word(base, w)[i + 1]; \
+		temp2 &= mask >> (off ? (32 - off) : 0); \
+		temp1 |= temp2 << (off ? (32 - off) : 0); \
+	} \
+	temp1; \
+})
+
+
+void clk_enable(struct clk *clk)
+{
+	if (clk) {
+		if (clk->usecount++ == 0) {
+			clk->enable(clk);
+		}
+	}
+}
+
+void clk_disable(struct clk *clk)
+{
+	if (clk) {
+		if (!(--clk->usecount)) {
+			if (clk->disable)
+				clk->disable(clk);
+		}
+	}
+}
+
+int clk_get_usecount(struct clk *clk)
+{
+	if (clk == NULL)
+		return 0;
+
+	return clk->usecount;
+}
+
+u32 clk_get_rate(struct clk *clk)
+{
+	if (!clk)
+		return 0;
+
+	return clk->rate;
+}
+
+struct clk *clk_get_parent(struct clk *clk)
+{
+	if (!clk)
+		return 0;
+
+	return clk->parent;
+}
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	if (clk && clk->set_rate)
+		clk->set_rate(clk, rate);
+	return clk->rate;
+}
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	if (clk == NULL || !clk->round_rate)
+		return 0;
+
+	return clk->round_rate(clk, rate);
+}
+
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	clk->parent = parent;
+	if (clk->set_parent)
+		return clk->set_parent(clk, parent);
+	return 0;
+}
+
+static int clk_ipu_enable(struct clk *clk)
+{
+	u32 reg;
+
+	reg = __raw_readl(clk->enable_reg);
+	reg |= MXC_CCM_CCGR_CG_MASK << clk->enable_shift;
+	__raw_writel(reg, clk->enable_reg);
+
+	/* Handshake with IPU when certain clock rates are changed. */
+	reg = __raw_readl(&mxc_ccm->ccdr);
+	reg &= ~MXC_CCM_CCDR_IPU_HS_MASK;
+	__raw_writel(reg, &mxc_ccm->ccdr);
+
+	/* Handshake with IPU when LPM is entered as its enabled. */
+	reg = __raw_readl(&mxc_ccm->clpcr);
+	reg &= ~MXC_CCM_CLPCR_BYPASS_IPU_LPM_HS;
+	__raw_writel(reg, &mxc_ccm->clpcr);
+
+	return 0;
+}
+
+static void clk_ipu_disable(struct clk *clk)
+{
+	u32 reg;
+
+	reg = __raw_readl(clk->enable_reg);
+	reg &= ~(MXC_CCM_CCGR_CG_MASK << clk->enable_shift);
+	__raw_writel(reg, clk->enable_reg);
+
+	/*
+	 * No handshake with IPU whe dividers are changed
+	 * as its not enabled.
+	 */
+	reg = __raw_readl(&mxc_ccm->ccdr);
+	reg |= MXC_CCM_CCDR_IPU_HS_MASK;
+	__raw_writel(reg, &mxc_ccm->ccdr);
+
+	/* No handshake with IPU when LPM is entered as its not enabled. */
+	reg = __raw_readl(&mxc_ccm->clpcr);
+	reg |= MXC_CCM_CLPCR_BYPASS_IPU_LPM_HS;
+	__raw_writel(reg, &mxc_ccm->clpcr);
+}
+
+
+static struct clk ipu_clk = {
+	.name = "ipu_clk",
+	.rate = 133000000,
+	.enable_reg = (u32 *)(MXC_CCM_BASE +
+		offsetof(struct mxc_ccm_reg, CCGR5)),
+	.enable_shift = MXC_CCM_CCGR5_CG5_OFFSET,
+	.enable = clk_ipu_enable,
+	.disable = clk_ipu_disable,
+	.usecount = 0,
+};
+
+/* Globals */
+struct clk *g_ipu_clk;
+unsigned char g_ipu_clk_enabled;
+struct clk *g_di_clk[2];
+struct clk *g_pixel_clk[2];
+unsigned char g_dc_di_assignment[10];
+uint32_t g_channel_init_mask;
+uint32_t g_channel_enable_mask;
+
+static int ipu_dc_use_count;
+static int ipu_dp_use_count;
+static int ipu_dmfc_use_count;
+static int ipu_di_use_count[2];
+
+u32 *ipu_cpmem_base;
+u32 *ipu_dc_tmpl_reg;
+
+/* Static functions */
+
+static inline void ipu_ch_param_set_high_priority(uint32_t ch)
+{
+	ipu_ch_param_mod_field(ipu_ch_param_addr(ch), 1, 93, 2, 1);
+};
+
+static inline uint32_t channel_2_dma(ipu_channel_t ch, ipu_buffer_t type)
+{
+	return ((uint32_t) ch >> (6 * type)) & 0x3F;
+};
+
+/* Either DP BG or DP FG can be graphic window */
+static inline int ipu_is_dp_graphic_chan(uint32_t dma_chan)
+{
+	return (dma_chan == 23 || dma_chan == 27);
+}
+
+static inline int ipu_is_dmfc_chan(uint32_t dma_chan)
+{
+	return ((dma_chan >= 23) && (dma_chan <= 29));
+}
+
+
+static inline void ipu_ch_param_set_buffer(uint32_t ch, int bufNum,
+					    dma_addr_t phyaddr)
+{
+	ipu_ch_param_mod_field(ipu_ch_param_addr(ch), 1, 29 * bufNum, 29,
+			       phyaddr / 8);
+};
+
+#define idma_is_valid(ch)	(ch != NO_DMA)
+#define idma_mask(ch)		(idma_is_valid(ch) ? (1UL << (ch & 0x1F)) : 0)
+#define idma_is_set(reg, dma)	(__raw_readl(reg(dma)) & idma_mask(dma))
+
+static void ipu_pixel_clk_recalc(struct clk *clk)
+{
+	u32 div = __raw_readl(DI_BS_CLKGEN0(clk->id));
+	if (div == 0)
+		clk->rate = 0;
+	else
+		clk->rate = (clk->parent->rate * 16) / div;
+}
+
+static unsigned long ipu_pixel_clk_round_rate(struct clk *clk,
+	unsigned long rate)
+{
+	u32 div, div1;
+	u32 tmp;
+	/*
+	 * Calculate divider
+	 * Fractional part is 4 bits,
+	 * so simply multiply by 2^4 to get fractional part.
+	 */
+	tmp = (clk->parent->rate * 16);
+	div = tmp / rate;
+
+	if (div < 0x10)            /* Min DI disp clock divider is 1 */
+		div = 0x10;
+	if (div & ~0xFEF)
+		div &= 0xFF8;
+	else {
+		div1 = div & 0xFE0;
+		if ((tmp/div1 - tmp/div) < rate / 4)
+			div = div1;
+		else
+			div &= 0xFF8;
+	}
+	return (clk->parent->rate * 16) / div;
+}
+
+static int ipu_pixel_clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	u32 div = (clk->parent->rate * 16) / rate;
+
+	__raw_writel(div, DI_BS_CLKGEN0(clk->id));
+
+	/* Setup pixel clock timing */
+	__raw_writel((div / 16) << 16, DI_BS_CLKGEN1(clk->id));
+
+	clk->rate = (clk->parent->rate * 16) / div;
+	return 0;
+}
+
+static int ipu_pixel_clk_enable(struct clk *clk)
+{
+	u32 disp_gen = __raw_readl(IPU_DISP_GEN);
+	disp_gen |= clk->id ? DI1_COUNTER_RELEASE : DI0_COUNTER_RELEASE;
+	__raw_writel(disp_gen, IPU_DISP_GEN);
+
+	return 0;
+}
+
+static void ipu_pixel_clk_disable(struct clk *clk)
+{
+	u32 disp_gen = __raw_readl(IPU_DISP_GEN);
+	disp_gen &= clk->id ? ~DI1_COUNTER_RELEASE : ~DI0_COUNTER_RELEASE;
+	__raw_writel(disp_gen, IPU_DISP_GEN);
+
+}
+
+static int ipu_pixel_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	u32 di_gen = __raw_readl(DI_GENERAL(clk->id));
+
+	if (parent == g_ipu_clk)
+		di_gen &= ~DI_GEN_DI_CLK_EXT;
+	else if (!IS_ERR(g_di_clk[clk->id]) && parent == g_di_clk[clk->id])
+		di_gen |= DI_GEN_DI_CLK_EXT;
+	else
+		return -EINVAL;
+
+	__raw_writel(di_gen, DI_GENERAL(clk->id));
+	ipu_pixel_clk_recalc(clk);
+	return 0;
+}
+
+static struct clk pixel_clk[] = {
+	{
+	.name = "pixel_clk",
+	.id = 0,
+	.recalc = ipu_pixel_clk_recalc,
+	.set_rate = ipu_pixel_clk_set_rate,
+	.round_rate = ipu_pixel_clk_round_rate,
+	.set_parent = ipu_pixel_clk_set_parent,
+	.enable = ipu_pixel_clk_enable,
+	.disable = ipu_pixel_clk_disable,
+	.usecount = 0,
+	},
+	{
+	.name = "pixel_clk",
+	.id = 1,
+	.recalc = ipu_pixel_clk_recalc,
+	.set_rate = ipu_pixel_clk_set_rate,
+	.round_rate = ipu_pixel_clk_round_rate,
+	.set_parent = ipu_pixel_clk_set_parent,
+	.enable = ipu_pixel_clk_enable,
+	.disable = ipu_pixel_clk_disable,
+	.usecount = 0,
+	},
+};
+
+/*
+ * This function resets IPU
+ */
+void ipu_reset(void)
+{
+	u32 *reg;
+	u32 value;
+
+	reg = (u32 *)SRC_BASE_ADDR;
+	value = __raw_readl(reg);
+	value = value | SW_IPU_RST;
+	__raw_writel(value, reg);
+}
+
+/*
+ * This function is called by the driver framework to initialize the IPU
+ * hardware.
+ *
+ * @param	dev	The device structure for the IPU passed in by the
+ *			driver framework.
+ *
+ * @return      Returns 0 on success or negative error code on error
+ */
+int ipu_probe(void)
+{
+	unsigned long ipu_base;
+	u32 temp;
+
+	u32 *reg_hsc_mcd = (u32 *)MIPI_HSC_BASE_ADDR;
+	u32 *reg_hsc_mxt_conf = (u32 *)(MIPI_HSC_BASE_ADDR + 0x800);
+
+	 __raw_writel(0xF00, reg_hsc_mcd);
+
+	/* CSI mode reserved*/
+	temp = __raw_readl(reg_hsc_mxt_conf);
+	 __raw_writel(temp | 0x0FF, reg_hsc_mxt_conf);
+
+	temp = __raw_readl(reg_hsc_mxt_conf);
+	__raw_writel(temp | 0x10000, reg_hsc_mxt_conf);
+
+	ipu_base = IPU_CTRL_BASE_ADDR;
+	ipu_cpmem_base = (u32 *)(ipu_base + IPU_CPMEM_REG_BASE);
+	ipu_dc_tmpl_reg = (u32 *)(ipu_base + IPU_DC_TMPL_REG_BASE);
+
+	g_pixel_clk[0] = &pixel_clk[0];
+	g_pixel_clk[1] = &pixel_clk[1];
+
+	g_ipu_clk = &ipu_clk;
+	debug("ipu_clk = %u\n", clk_get_rate(g_ipu_clk));
+
+	ipu_reset();
+
+	clk_set_parent(g_pixel_clk[0], g_ipu_clk);
+	clk_set_parent(g_pixel_clk[1], g_ipu_clk);
+	clk_enable(g_ipu_clk);
+
+	g_di_clk[0] = NULL;
+	g_di_clk[1] = NULL;
+
+	__raw_writel(0x807FFFFF, IPU_MEM_RST);
+	while (__raw_readl(IPU_MEM_RST) & 0x80000000)
+		;
+
+	ipu_init_dc_mappings();
+
+	__raw_writel(0, IPU_INT_CTRL(5));
+	__raw_writel(0, IPU_INT_CTRL(6));
+	__raw_writel(0, IPU_INT_CTRL(9));
+	__raw_writel(0, IPU_INT_CTRL(10));
+
+	/* DMFC Init */
+	ipu_dmfc_init(DMFC_NORMAL, 1);
+
+	/* Set sync refresh channels as high priority */
+	__raw_writel(0x18800000L, IDMAC_CHA_PRI(0));
+
+	/* Set MCU_T to divide MCU access window into 2 */
+	__raw_writel(0x00400000L | (IPU_MCU_T_DEFAULT << 18), IPU_DISP_GEN);
+
+	clk_disable(g_ipu_clk);
+
+	return 0;
+}
+
+void ipu_dump_registers(void)
+{
+	debug("IPU_CONF = \t0x%08X\n", __raw_readl(IPU_CONF));
+	debug("IDMAC_CONF = \t0x%08X\n", __raw_readl(IDMAC_CONF));
+	debug("IDMAC_CHA_EN1 = \t0x%08X\n",
+	       __raw_readl(IDMAC_CHA_EN(0)));
+	debug("IDMAC_CHA_EN2 = \t0x%08X\n",
+	       __raw_readl(IDMAC_CHA_EN(32)));
+	debug("IDMAC_CHA_PRI1 = \t0x%08X\n",
+	       __raw_readl(IDMAC_CHA_PRI(0)));
+	debug("IDMAC_CHA_PRI2 = \t0x%08X\n",
+	       __raw_readl(IDMAC_CHA_PRI(32)));
+	debug("IPU_CHA_DB_MODE_SEL0 = \t0x%08X\n",
+	       __raw_readl(IPU_CHA_DB_MODE_SEL(0)));
+	debug("IPU_CHA_DB_MODE_SEL1 = \t0x%08X\n",
+	       __raw_readl(IPU_CHA_DB_MODE_SEL(32)));
+	debug("DMFC_WR_CHAN = \t0x%08X\n",
+	       __raw_readl(DMFC_WR_CHAN));
+	debug("DMFC_WR_CHAN_DEF = \t0x%08X\n",
+	       __raw_readl(DMFC_WR_CHAN_DEF));
+	debug("DMFC_DP_CHAN = \t0x%08X\n",
+	       __raw_readl(DMFC_DP_CHAN));
+	debug("DMFC_DP_CHAN_DEF = \t0x%08X\n",
+	       __raw_readl(DMFC_DP_CHAN_DEF));
+	debug("DMFC_IC_CTRL = \t0x%08X\n",
+	       __raw_readl(DMFC_IC_CTRL));
+	debug("IPU_FS_PROC_FLOW1 = \t0x%08X\n",
+	       __raw_readl(IPU_FS_PROC_FLOW1));
+	debug("IPU_FS_PROC_FLOW2 = \t0x%08X\n",
+	       __raw_readl(IPU_FS_PROC_FLOW2));
+	debug("IPU_FS_PROC_FLOW3 = \t0x%08X\n",
+	       __raw_readl(IPU_FS_PROC_FLOW3));
+	debug("IPU_FS_DISP_FLOW1 = \t0x%08X\n",
+	       __raw_readl(IPU_FS_DISP_FLOW1));
+}
+
+/*
+ * This function is called to initialize a logical IPU channel.
+ *
+ * @param       channel Input parameter for the logical channel ID to init.
+ *
+ * @param       params  Input parameter containing union of channel
+ *                      initialization parameters.
+ *
+ * @return      Returns 0 on success or negative error code on fail
+ */
+int32_t ipu_init_channel(ipu_channel_t channel, ipu_channel_params_t *params)
+{
+	int ret = 0;
+	uint32_t ipu_conf;
+
+	debug("init channel = %d\n", IPU_CHAN_ID(channel));
+
+	if (g_ipu_clk_enabled == 0) {
+		g_ipu_clk_enabled = 1;
+		clk_enable(g_ipu_clk);
+	}
+
+
+	if (g_channel_init_mask & (1L << IPU_CHAN_ID(channel))) {
+		printf("Warning: channel already initialized %d\n",
+			IPU_CHAN_ID(channel));
+	}
+
+	ipu_conf = __raw_readl(IPU_CONF);
+
+	switch (channel) {
+	case MEM_DC_SYNC:
+		if (params->mem_dc_sync.di > 1) {
+			ret = -EINVAL;
+			goto err;
+		}
+
+		g_dc_di_assignment[1] = params->mem_dc_sync.di;
+		ipu_dc_init(1, params->mem_dc_sync.di,
+			     params->mem_dc_sync.interlaced);
+		ipu_di_use_count[params->mem_dc_sync.di]++;
+		ipu_dc_use_count++;
+		ipu_dmfc_use_count++;
+		break;
+	case MEM_BG_SYNC:
+		if (params->mem_dp_bg_sync.di > 1) {
+			ret = -EINVAL;
+			goto err;
+		}
+
+		g_dc_di_assignment[5] = params->mem_dp_bg_sync.di;
+		ipu_dp_init(channel, params->mem_dp_bg_sync.in_pixel_fmt,
+			     params->mem_dp_bg_sync.out_pixel_fmt);
+		ipu_dc_init(5, params->mem_dp_bg_sync.di,
+			     params->mem_dp_bg_sync.interlaced);
+		ipu_di_use_count[params->mem_dp_bg_sync.di]++;
+		ipu_dc_use_count++;
+		ipu_dp_use_count++;
+		ipu_dmfc_use_count++;
+		break;
+	case MEM_FG_SYNC:
+		ipu_dp_init(channel, params->mem_dp_fg_sync.in_pixel_fmt,
+			     params->mem_dp_fg_sync.out_pixel_fmt);
+
+		ipu_dc_use_count++;
+		ipu_dp_use_count++;
+		ipu_dmfc_use_count++;
+		break;
+	default:
+		printf("Missing channel initialization\n");
+		break;
+	}
+
+	/* Enable IPU sub module */
+	g_channel_init_mask |= 1L << IPU_CHAN_ID(channel);
+	if (ipu_dc_use_count == 1)
+		ipu_conf |= IPU_CONF_DC_EN;
+	if (ipu_dp_use_count == 1)
+		ipu_conf |= IPU_CONF_DP_EN;
+	if (ipu_dmfc_use_count == 1)
+		ipu_conf |= IPU_CONF_DMFC_EN;
+	if (ipu_di_use_count[0] == 1) {
+		ipu_conf |= IPU_CONF_DI0_EN;
+	}
+	if (ipu_di_use_count[1] == 1) {
+		ipu_conf |= IPU_CONF_DI1_EN;
+	}
+
+	__raw_writel(ipu_conf, IPU_CONF);
+
+err:
+	return ret;
+}
+
+/*
+ * This function is called to uninitialize a logical IPU channel.
+ *
+ * @param       channel Input parameter for the logical channel ID to uninit.
+ */
+void ipu_uninit_channel(ipu_channel_t channel)
+{
+	uint32_t reg;
+	uint32_t in_dma, out_dma = 0;
+	uint32_t ipu_conf;
+
+	if ((g_channel_init_mask & (1L << IPU_CHAN_ID(channel))) == 0) {
+		debug("Channel already uninitialized %d\n",
+			IPU_CHAN_ID(channel));
+		return;
+	}
+
+	/*
+	 * Make sure channel is disabled
+	 * Get input and output dma channels
+	 */
+	in_dma = channel_2_dma(channel, IPU_OUTPUT_BUFFER);
+	out_dma = channel_2_dma(channel, IPU_VIDEO_IN_BUFFER);
+
+	if (idma_is_set(IDMAC_CHA_EN, in_dma) ||
+	    idma_is_set(IDMAC_CHA_EN, out_dma)) {
+		printf(
+			"Channel %d is not disabled, disable first\n",
+			IPU_CHAN_ID(channel));
+		return;
+	}
+
+	ipu_conf = __raw_readl(IPU_CONF);
+
+	/* Reset the double buffer */
+	reg = __raw_readl(IPU_CHA_DB_MODE_SEL(in_dma));
+	__raw_writel(reg & ~idma_mask(in_dma), IPU_CHA_DB_MODE_SEL(in_dma));
+	reg = __raw_readl(IPU_CHA_DB_MODE_SEL(out_dma));
+	__raw_writel(reg & ~idma_mask(out_dma), IPU_CHA_DB_MODE_SEL(out_dma));
+
+	switch (channel) {
+	case MEM_DC_SYNC:
+		ipu_dc_uninit(1);
+		ipu_di_use_count[g_dc_di_assignment[1]]--;
+		ipu_dc_use_count--;
+		ipu_dmfc_use_count--;
+		break;
+	case MEM_BG_SYNC:
+		ipu_dp_uninit(channel);
+		ipu_dc_uninit(5);
+		ipu_di_use_count[g_dc_di_assignment[5]]--;
+		ipu_dc_use_count--;
+		ipu_dp_use_count--;
+		ipu_dmfc_use_count--;
+		break;
+	case MEM_FG_SYNC:
+		ipu_dp_uninit(channel);
+		ipu_dc_use_count--;
+		ipu_dp_use_count--;
+		ipu_dmfc_use_count--;
+		break;
+	default:
+		break;
+	}
+
+	g_channel_init_mask &= ~(1L << IPU_CHAN_ID(channel));
+
+	if (ipu_dc_use_count == 0)
+		ipu_conf &= ~IPU_CONF_DC_EN;
+	if (ipu_dp_use_count == 0)
+		ipu_conf &= ~IPU_CONF_DP_EN;
+	if (ipu_dmfc_use_count == 0)
+		ipu_conf &= ~IPU_CONF_DMFC_EN;
+	if (ipu_di_use_count[0] == 0) {
+		ipu_conf &= ~IPU_CONF_DI0_EN;
+	}
+	if (ipu_di_use_count[1] == 0) {
+		ipu_conf &= ~IPU_CONF_DI1_EN;
+	}
+
+	__raw_writel(ipu_conf, IPU_CONF);
+
+	if (ipu_conf == 0) {
+		clk_disable(g_ipu_clk);
+		g_ipu_clk_enabled = 0;
+	}
+
+}
+
+static inline void ipu_ch_param_dump(int ch)
+{
+#ifdef DEBUG
+	struct ipu_ch_param *p = ipu_ch_param_addr(ch);
+	debug("ch %d word 0 - %08X %08X %08X %08X %08X\n", ch,
+		 p->word[0].data[0], p->word[0].data[1], p->word[0].data[2],
+		 p->word[0].data[3], p->word[0].data[4]);
+	debug("ch %d word 1 - %08X %08X %08X %08X %08X\n", ch,
+		 p->word[1].data[0], p->word[1].data[1], p->word[1].data[2],
+		 p->word[1].data[3], p->word[1].data[4]);
+	debug("PFS 0x%x, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 85, 4));
+	debug("BPP 0x%x, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 0, 107, 3));
+	debug("NPB 0x%x\n",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 78, 7));
+
+	debug("FW %d, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 0, 125, 13));
+	debug("FH %d, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 0, 138, 12));
+	debug("Stride %d\n",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 102, 14));
+
+	debug("Width0 %d+1, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 116, 3));
+	debug("Width1 %d+1, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 119, 3));
+	debug("Width2 %d+1, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 122, 3));
+	debug("Width3 %d+1, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 125, 3));
+	debug("Offset0 %d, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 128, 5));
+	debug("Offset1 %d, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 133, 5));
+	debug("Offset2 %d, ",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 138, 5));
+	debug("Offset3 %d\n",
+		 ipu_ch_param_read_field(ipu_ch_param_addr(ch), 1, 143, 5));
+#endif
+}
+
+static inline void ipu_ch_params_set_packing(struct ipu_ch_param *p,
+					      int red_width, int red_offset,
+					      int green_width, int green_offset,
+					      int blue_width, int blue_offset,
+					      int alpha_width, int alpha_offset)
+{
+	/* Setup red width and offset */
+	ipu_ch_param_set_field(p, 1, 116, 3, red_width - 1);
+	ipu_ch_param_set_field(p, 1, 128, 5, red_offset);
+	/* Setup green width and offset */
+	ipu_ch_param_set_field(p, 1, 119, 3, green_width - 1);
+	ipu_ch_param_set_field(p, 1, 133, 5, green_offset);
+	/* Setup blue width and offset */
+	ipu_ch_param_set_field(p, 1, 122, 3, blue_width - 1);
+	ipu_ch_param_set_field(p, 1, 138, 5, blue_offset);
+	/* Setup alpha width and offset */
+	ipu_ch_param_set_field(p, 1, 125, 3, alpha_width - 1);
+	ipu_ch_param_set_field(p, 1, 143, 5, alpha_offset);
+}
+
+static void ipu_ch_param_init(int ch,
+			      uint32_t pixel_fmt, uint32_t width,
+			      uint32_t height, uint32_t stride,
+			      uint32_t u, uint32_t v,
+			      uint32_t uv_stride, dma_addr_t addr0,
+			      dma_addr_t addr1)
+{
+	uint32_t u_offset = 0;
+	uint32_t v_offset = 0;
+	struct ipu_ch_param params;
+
+	memset(&params, 0, sizeof(params));
+
+	ipu_ch_param_set_field(&params, 0, 125, 13, width - 1);
+
+	if ((ch == 8) || (ch == 9) || (ch == 10)) {
+		ipu_ch_param_set_field(&params, 0, 138, 12, (height / 2) - 1);
+		ipu_ch_param_set_field(&params, 1, 102, 14, (stride * 2) - 1);
+	} else {
+		ipu_ch_param_set_field(&params, 0, 138, 12, height - 1);
+		ipu_ch_param_set_field(&params, 1, 102, 14, stride - 1);
+	}
+
+	ipu_ch_param_set_field(&params, 1, 0, 29, addr0 >> 3);
+	ipu_ch_param_set_field(&params, 1, 29, 29, addr1 >> 3);
+
+	switch (pixel_fmt) {
+	case IPU_PIX_FMT_GENERIC:
+		/*Represents 8-bit Generic data */
+		ipu_ch_param_set_field(&params, 0, 107, 3, 5);	/* bits/pixel */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 6);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 63);	/* burst size */
+
+		break;
+	case IPU_PIX_FMT_GENERIC_32:
+		/*Represents 32-bit Generic data */
+		break;
+	case IPU_PIX_FMT_RGB565:
+		ipu_ch_param_set_field(&params, 0, 107, 3, 3);	/* bits/pixel */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 7);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 15);	/* burst size */
+
+		ipu_ch_params_set_packing(&params, 5, 0, 6, 5, 5, 11, 8, 16);
+		break;
+	case IPU_PIX_FMT_BGR24:
+		ipu_ch_param_set_field(&params, 0, 107, 3, 1);	/* bits/pixel */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 7);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 19);	/* burst size */
+
+		ipu_ch_params_set_packing(&params, 8, 0, 8, 8, 8, 16, 8, 24);
+		break;
+	case IPU_PIX_FMT_RGB24:
+	case IPU_PIX_FMT_YUV444:
+		ipu_ch_param_set_field(&params, 0, 107, 3, 1);	/* bits/pixel */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 7);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 19);	/* burst size */
+
+		ipu_ch_params_set_packing(&params, 8, 16, 8, 8, 8, 0, 8, 24);
+		break;
+	case IPU_PIX_FMT_BGRA32:
+	case IPU_PIX_FMT_BGR32:
+		ipu_ch_param_set_field(&params, 0, 107, 3, 0);	/* bits/pixel */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 7);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 15);	/* burst size */
+
+		ipu_ch_params_set_packing(&params, 8, 8, 8, 16, 8, 24, 8, 0);
+		break;
+	case IPU_PIX_FMT_RGBA32:
+	case IPU_PIX_FMT_RGB32:
+		ipu_ch_param_set_field(&params, 0, 107, 3, 0);	/* bits/pixel */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 7);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 15);	/* burst size */
+
+		ipu_ch_params_set_packing(&params, 8, 24, 8, 16, 8, 8, 8, 0);
+		break;
+	case IPU_PIX_FMT_ABGR32:
+		ipu_ch_param_set_field(&params, 0, 107, 3, 0);	/* bits/pixel */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 7);	/* pix format */
+
+		ipu_ch_params_set_packing(&params, 8, 0, 8, 8, 8, 16, 8, 24);
+		break;
+	case IPU_PIX_FMT_UYVY:
+		ipu_ch_param_set_field(&params, 0, 107, 3, 3);	/* bits/pixel */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 0xA);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 15);	/* burst size */
+		break;
+	case IPU_PIX_FMT_YUYV:
+		ipu_ch_param_set_field(&params, 0, 107, 3, 3);	/* bits/pixel */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 0x8);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 31);	/* burst size */
+		break;
+	case IPU_PIX_FMT_YUV420P2:
+	case IPU_PIX_FMT_YUV420P:
+		ipu_ch_param_set_field(&params, 1, 85, 4, 2);	/* pix format */
+
+		if (uv_stride < stride / 2)
+			uv_stride = stride / 2;
+
+		u_offset = stride * height;
+		v_offset = u_offset + (uv_stride * height / 2);
+		/* burst size */
+		if ((ch == 8) || (ch == 9) || (ch == 10)) {
+			ipu_ch_param_set_field(&params, 1, 78, 7, 15);
+			uv_stride = uv_stride*2;
+		} else {
+			ipu_ch_param_set_field(&params, 1, 78, 7, 31);
+		}
+		break;
+	case IPU_PIX_FMT_YVU422P:
+		/* BPP & pixel format */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 1);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 31);	/* burst size */
+
+		if (uv_stride < stride / 2)
+			uv_stride = stride / 2;
+
+		v_offset = (v == 0) ? stride * height : v;
+		u_offset = (u == 0) ? v_offset + v_offset / 2 : u;
+		break;
+	case IPU_PIX_FMT_YUV422P:
+		/* BPP & pixel format */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 1);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 31);	/* burst size */
+
+		if (uv_stride < stride / 2)
+			uv_stride = stride / 2;
+
+		u_offset = (u == 0) ? stride * height : u;
+		v_offset = (v == 0) ? u_offset + u_offset / 2 : v;
+		break;
+	case IPU_PIX_FMT_NV12:
+		/* BPP & pixel format */
+		ipu_ch_param_set_field(&params, 1, 85, 4, 4);	/* pix format */
+		ipu_ch_param_set_field(&params, 1, 78, 7, 31);	/* burst size */
+		uv_stride = stride;
+		u_offset = (u == 0) ? stride * height : u;
+		break;
+	default:
+		puts("mxc ipu: unimplemented pixel format\n");
+		break;
+	}
+
+
+	if (uv_stride)
+		ipu_ch_param_set_field(&params, 1, 128, 14, uv_stride - 1);
+
+	/* Get the uv offset from user when need cropping */
+	if (u || v) {
+		u_offset = u;
+		v_offset = v;
+	}
+
+	/* UBO and VBO are 22-bit */
+	if (u_offset/8 > 0x3fffff)
+		puts("The value of U offset exceeds IPU limitation\n");
+	if (v_offset/8 > 0x3fffff)
+		puts("The value of V offset exceeds IPU limitation\n");
+
+	ipu_ch_param_set_field(&params, 0, 46, 22, u_offset / 8);
+	ipu_ch_param_set_field(&params, 0, 68, 22, v_offset / 8);
+
+	debug("initializing idma ch %d @ %p\n", ch, ipu_ch_param_addr(ch));
+	memcpy(ipu_ch_param_addr(ch), &params, sizeof(params));
+};
+
+/*
+ * This function is called to initialize a buffer for logical IPU channel.
+ *
+ * @param       channel         Input parameter for the logical channel ID.
+ *
+ * @param       type            Input parameter which buffer to initialize.
+ *
+ * @param       pixel_fmt       Input parameter for pixel format of buffer.
+ *                              Pixel format is a FOURCC ASCII code.
+ *
+ * @param       width           Input parameter for width of buffer in pixels.
+ *
+ * @param       height          Input parameter for height of buffer in pixels.
+ *
+ * @param       stride          Input parameter for stride length of buffer
+ *                              in pixels.
+ *
+ * @param       phyaddr_0       Input parameter buffer 0 physical address.
+ *
+ * @param       phyaddr_1       Input parameter buffer 1 physical address.
+ *                              Setting this to a value other than NULL enables
+ *                              double buffering mode.
+ *
+ * @param       u		private u offset for additional cropping,
+ *				zero if not used.
+ *
+ * @param       v		private v offset for additional cropping,
+ *				zero if not used.
+ *
+ * @return      Returns 0 on success or negative error code on fail
+ */
+int32_t ipu_init_channel_buffer(ipu_channel_t channel, ipu_buffer_t type,
+				uint32_t pixel_fmt,
+				uint16_t width, uint16_t height,
+				uint32_t stride,
+				dma_addr_t phyaddr_0, dma_addr_t phyaddr_1,
+				uint32_t u, uint32_t v)
+{
+	uint32_t reg;
+	uint32_t dma_chan;
+
+	dma_chan = channel_2_dma(channel, type);
+	if (!idma_is_valid(dma_chan))
+		return -EINVAL;
+
+	if (stride < width * bytes_per_pixel(pixel_fmt))
+		stride = width * bytes_per_pixel(pixel_fmt);
+
+	if (stride % 4) {
+		printf(
+			"Stride not 32-bit aligned, stride = %d\n", stride);
+		return -EINVAL;
+	}
+	/* Build parameter memory data for DMA channel */
+	ipu_ch_param_init(dma_chan, pixel_fmt, width, height, stride, u, v, 0,
+			   phyaddr_0, phyaddr_1);
+
+	if (ipu_is_dmfc_chan(dma_chan)) {
+		ipu_dmfc_set_wait4eot(dma_chan, width);
+	}
+
+	if (idma_is_set(IDMAC_CHA_PRI, dma_chan))
+		ipu_ch_param_set_high_priority(dma_chan);
+
+	ipu_ch_param_dump(dma_chan);
+
+	reg = __raw_readl(IPU_CHA_DB_MODE_SEL(dma_chan));
+	if (phyaddr_1)
+		reg |= idma_mask(dma_chan);
+	else
+		reg &= ~idma_mask(dma_chan);
+	__raw_writel(reg, IPU_CHA_DB_MODE_SEL(dma_chan));
+
+	/* Reset to buffer 0 */
+	__raw_writel(idma_mask(dma_chan), IPU_CHA_CUR_BUF(dma_chan));
+
+	return 0;
+}
+
+/*
+ * This function enables a logical channel.
+ *
+ * @param       channel         Input parameter for the logical channel ID.
+ *
+ * @return      This function returns 0 on success or negative error code on
+ *              fail.
+ */
+int32_t ipu_enable_channel(ipu_channel_t channel)
+{
+	uint32_t reg;
+	uint32_t in_dma;
+	uint32_t out_dma;
+
+	if (g_channel_enable_mask & (1L << IPU_CHAN_ID(channel))) {
+		printf("Warning: channel already enabled %d\n",
+			IPU_CHAN_ID(channel));
+	}
+
+	/* Get input and output dma channels */
+	out_dma = channel_2_dma(channel, IPU_OUTPUT_BUFFER);
+	in_dma = channel_2_dma(channel, IPU_VIDEO_IN_BUFFER);
+
+	if (idma_is_valid(in_dma)) {
+		reg = __raw_readl(IDMAC_CHA_EN(in_dma));
+		__raw_writel(reg | idma_mask(in_dma), IDMAC_CHA_EN(in_dma));
+	}
+	if (idma_is_valid(out_dma)) {
+		reg = __raw_readl(IDMAC_CHA_EN(out_dma));
+		__raw_writel(reg | idma_mask(out_dma), IDMAC_CHA_EN(out_dma));
+	}
+
+	if ((channel == MEM_DC_SYNC) || (channel == MEM_BG_SYNC) ||
+	    (channel == MEM_FG_SYNC))
+		ipu_dp_dc_enable(channel);
+
+	g_channel_enable_mask |= 1L << IPU_CHAN_ID(channel);
+
+	return 0;
+}
+
+/*
+ * This function clear buffer ready for a logical channel.
+ *
+ * @param       channel         Input parameter for the logical channel ID.
+ *
+ * @param       type            Input parameter which buffer to clear.
+ *
+ * @param       bufNum          Input parameter for which buffer number clear
+ *				ready state.
+ *
+ */
+void ipu_clear_buffer_ready(ipu_channel_t channel, ipu_buffer_t type,
+		uint32_t bufNum)
+{
+	uint32_t dma_ch = channel_2_dma(channel, type);
+
+	if (!idma_is_valid(dma_ch))
+		return;
+
+	__raw_writel(0xF0000000, IPU_GPR); /* write one to clear */
+	if (bufNum == 0) {
+		if (idma_is_set(IPU_CHA_BUF0_RDY, dma_ch)) {
+			__raw_writel(idma_mask(dma_ch),
+					IPU_CHA_BUF0_RDY(dma_ch));
+		}
+	} else {
+		if (idma_is_set(IPU_CHA_BUF1_RDY, dma_ch)) {
+			__raw_writel(idma_mask(dma_ch),
+					IPU_CHA_BUF1_RDY(dma_ch));
+		}
+	}
+	__raw_writel(0x0, IPU_GPR); /* write one to set */
+}
+
+/*
+ * This function disables a logical channel.
+ *
+ * @param       channel         Input parameter for the logical channel ID.
+ *
+ * @param       wait_for_stop   Flag to set whether to wait for channel end
+ *                              of frame or return immediately.
+ *
+ * @return      This function returns 0 on success or negative error code on
+ *              fail.
+ */
+int32_t ipu_disable_channel(ipu_channel_t channel)
+{
+	uint32_t reg;
+	uint32_t in_dma;
+	uint32_t out_dma;
+
+	if ((g_channel_enable_mask & (1L << IPU_CHAN_ID(channel))) == 0) {
+		debug("Channel already disabled %d\n",
+			IPU_CHAN_ID(channel));
+		return 0;
+	}
+
+	/* Get input and output dma channels */
+	out_dma = channel_2_dma(channel, IPU_OUTPUT_BUFFER);
+	in_dma = channel_2_dma(channel, IPU_VIDEO_IN_BUFFER);
+
+	if ((idma_is_valid(in_dma) &&
+		!idma_is_set(IDMAC_CHA_EN, in_dma))
+		&& (idma_is_valid(out_dma) &&
+		!idma_is_set(IDMAC_CHA_EN, out_dma)))
+		return -EINVAL;
+
+	if ((channel == MEM_BG_SYNC) || (channel == MEM_FG_SYNC) ||
+	    (channel == MEM_DC_SYNC)) {
+		ipu_dp_dc_disable(channel, 0);
+	}
+
+	/* Disable DMA channel(s) */
+	if (idma_is_valid(in_dma)) {
+		reg = __raw_readl(IDMAC_CHA_EN(in_dma));
+		__raw_writel(reg & ~idma_mask(in_dma), IDMAC_CHA_EN(in_dma));
+		__raw_writel(idma_mask(in_dma), IPU_CHA_CUR_BUF(in_dma));
+	}
+	if (idma_is_valid(out_dma)) {
+		reg = __raw_readl(IDMAC_CHA_EN(out_dma));
+		__raw_writel(reg & ~idma_mask(out_dma), IDMAC_CHA_EN(out_dma));
+		__raw_writel(idma_mask(out_dma), IPU_CHA_CUR_BUF(out_dma));
+	}
+
+	g_channel_enable_mask &= ~(1L << IPU_CHAN_ID(channel));
+
+	/* Set channel buffers NOT to be ready */
+	if (idma_is_valid(in_dma)) {
+		ipu_clear_buffer_ready(channel, IPU_VIDEO_IN_BUFFER, 0);
+		ipu_clear_buffer_ready(channel, IPU_VIDEO_IN_BUFFER, 1);
+	}
+	if (idma_is_valid(out_dma)) {
+		ipu_clear_buffer_ready(channel, IPU_OUTPUT_BUFFER, 0);
+		ipu_clear_buffer_ready(channel, IPU_OUTPUT_BUFFER, 1);
+	}
+
+	return 0;
+}
+
+uint32_t bytes_per_pixel(uint32_t fmt)
+{
+	switch (fmt) {
+	case IPU_PIX_FMT_GENERIC:	/*generic data */
+	case IPU_PIX_FMT_RGB332:
+	case IPU_PIX_FMT_YUV420P:
+	case IPU_PIX_FMT_YUV422P:
+		return 1;
+		break;
+	case IPU_PIX_FMT_RGB565:
+	case IPU_PIX_FMT_YUYV:
+	case IPU_PIX_FMT_UYVY:
+		return 2;
+		break;
+	case IPU_PIX_FMT_BGR24:
+	case IPU_PIX_FMT_RGB24:
+		return 3;
+		break;
+	case IPU_PIX_FMT_GENERIC_32:	/*generic data */
+	case IPU_PIX_FMT_BGR32:
+	case IPU_PIX_FMT_BGRA32:
+	case IPU_PIX_FMT_RGB32:
+	case IPU_PIX_FMT_RGBA32:
+	case IPU_PIX_FMT_ABGR32:
+		return 4;
+		break;
+	default:
+		return 1;
+		break;
+	}
+	return 0;
+}
+
+ipu_color_space_t format_to_colorspace(uint32_t fmt)
+{
+	switch (fmt) {
+	case IPU_PIX_FMT_RGB666:
+	case IPU_PIX_FMT_RGB565:
+	case IPU_PIX_FMT_BGR24:
+	case IPU_PIX_FMT_RGB24:
+	case IPU_PIX_FMT_BGR32:
+	case IPU_PIX_FMT_BGRA32:
+	case IPU_PIX_FMT_RGB32:
+	case IPU_PIX_FMT_RGBA32:
+	case IPU_PIX_FMT_ABGR32:
+	case IPU_PIX_FMT_LVDS666:
+	case IPU_PIX_FMT_LVDS888:
+		return RGB;
+		break;
+
+	default:
+		return YCbCr;
+		break;
+	}
+	return RGB;
+}
diff --git a/drivers/video/ipu_disp.c b/drivers/video/ipu_disp.c
new file mode 100644
index 0000000..11cf98d
--- /dev/null
+++ b/drivers/video/ipu_disp.c
@@ -0,0 +1,1359 @@
+/*
+ * Porting to u-boot:
+ *
+ * (C) Copyright 2010
+ * Stefano Babic, DENX Software Engineering, sbabic@denx.de
+ *
+ * Linux IPU driver for MX51:
+ *
+ * (C) Copyright 2005-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* #define DEBUG */
+
+#include <common.h>
+#include <linux/types.h>
+#include <asm/errno.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+#include "ipu.h"
+#include "ipu_regs.h"
+
+enum csc_type_t {
+	RGB2YUV = 0,
+	YUV2RGB,
+	RGB2RGB,
+	YUV2YUV,
+	CSC_NONE,
+	CSC_NUM
+};
+
+struct dp_csc_param_t {
+	int mode;
+	void *coeff;
+};
+
+#define SYNC_WAVE 0
+
+/* DC display ID assignments */
+#define DC_DISP_ID_SYNC(di)	(di)
+#define DC_DISP_ID_SERIAL	2
+#define DC_DISP_ID_ASYNC	3
+
+int dmfc_type_setup;
+static int dmfc_size_28, dmfc_size_29, dmfc_size_24, dmfc_size_27, dmfc_size_23;
+int g_di1_tvout;
+
+extern struct clk *g_ipu_clk;
+extern struct clk *g_di_clk[2];
+extern struct clk *g_pixel_clk[2];
+
+extern unsigned char g_ipu_clk_enabled;
+extern unsigned char g_dc_di_assignment[];
+
+void ipu_dmfc_init(int dmfc_type, int first)
+{
+	u32 dmfc_wr_chan, dmfc_dp_chan;
+
+	if (first) {
+		if (dmfc_type_setup > dmfc_type)
+			dmfc_type = dmfc_type_setup;
+		else
+			dmfc_type_setup = dmfc_type;
+
+		/* disable DMFC-IC channel*/
+		__raw_writel(0x2, DMFC_IC_CTRL);
+	} else if (dmfc_type_setup >= DMFC_HIGH_RESOLUTION_DC) {
+		printf("DMFC high resolution has set, will not change\n");
+		return;
+	} else
+		dmfc_type_setup = dmfc_type;
+
+	if (dmfc_type == DMFC_HIGH_RESOLUTION_DC) {
+		/* 1 - segment 0~3;
+		 * 5B - segement 4, 5;
+		 * 5F - segement 6, 7;
+		 * 1C, 2C and 6B, 6F unused;
+		 */
+		debug("IPU DMFC DC HIGH RES: 1(0~3), 5B(4,5), 5F(6,7)\n");
+		dmfc_wr_chan = 0x00000088;
+		dmfc_dp_chan = 0x00009694;
+		dmfc_size_28 = 256 * 4;
+		dmfc_size_29 = 0;
+		dmfc_size_24 = 0;
+		dmfc_size_27 = 128 * 4;
+		dmfc_size_23 = 128 * 4;
+	} else if (dmfc_type == DMFC_HIGH_RESOLUTION_DP) {
+		/* 1 - segment 0, 1;
+		 * 5B - segement 2~5;
+		 * 5F - segement 6,7;
+		 * 1C, 2C and 6B, 6F unused;
+		 */
+		debug("IPU DMFC DP HIGH RES: 1(0,1), 5B(2~5), 5F(6,7)\n");
+		dmfc_wr_chan = 0x00000090;
+		dmfc_dp_chan = 0x0000968a;
+		dmfc_size_28 = 128 * 4;
+		dmfc_size_29 = 0;
+		dmfc_size_24 = 0;
+		dmfc_size_27 = 128 * 4;
+		dmfc_size_23 = 256 * 4;
+	} else if (dmfc_type == DMFC_HIGH_RESOLUTION_ONLY_DP) {
+		/* 5B - segement 0~3;
+		 * 5F - segement 4~7;
+		 * 1, 1C, 2C and 6B, 6F unused;
+		 */
+		debug("IPU DMFC ONLY-DP HIGH RES: 5B(0~3), 5F(4~7)\n");
+		dmfc_wr_chan = 0x00000000;
+		dmfc_dp_chan = 0x00008c88;
+		dmfc_size_28 = 0;
+		dmfc_size_29 = 0;
+		dmfc_size_24 = 0;
+		dmfc_size_27 = 256 * 4;
+		dmfc_size_23 = 256 * 4;
+	} else {
+		/* 1 - segment 0, 1;
+		 * 5B - segement 4, 5;
+		 * 5F - segement 6, 7;
+		 * 1C, 2C and 6B, 6F unused;
+		 */
+		debug("IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)\n");
+		dmfc_wr_chan = 0x00000090;
+		dmfc_dp_chan = 0x00009694;
+		dmfc_size_28 = 128 * 4;
+		dmfc_size_29 = 0;
+		dmfc_size_24 = 0;
+		dmfc_size_27 = 128 * 4;
+		dmfc_size_23 = 128 * 4;
+	}
+	__raw_writel(dmfc_wr_chan, DMFC_WR_CHAN);
+	__raw_writel(0x202020F6, DMFC_WR_CHAN_DEF);
+	__raw_writel(dmfc_dp_chan, DMFC_DP_CHAN);
+	/* Enable chan 5 watermark set at 5 bursts and clear at 7 bursts */
+	__raw_writel(0x2020F6F6, DMFC_DP_CHAN_DEF);
+}
+
+void ipu_dmfc_set_wait4eot(int dma_chan, int width)
+{
+	u32 dmfc_gen1 = __raw_readl(DMFC_GENERAL1);
+
+	if (width >= HIGH_RESOLUTION_WIDTH) {
+		if (dma_chan == 23)
+			ipu_dmfc_init(DMFC_HIGH_RESOLUTION_DP, 0);
+		else if (dma_chan == 28)
+			ipu_dmfc_init(DMFC_HIGH_RESOLUTION_DC, 0);
+	}
+
+	if (dma_chan == 23) { /*5B*/
+		if (dmfc_size_23 / width > 3)
+			dmfc_gen1 |= 1UL << 20;
+		else
+			dmfc_gen1 &= ~(1UL << 20);
+	} else if (dma_chan == 24) { /*6B*/
+		if (dmfc_size_24 / width > 1)
+			dmfc_gen1 |= 1UL << 22;
+		else
+			dmfc_gen1 &= ~(1UL << 22);
+	} else if (dma_chan == 27) { /*5F*/
+		if (dmfc_size_27 / width > 2)
+			dmfc_gen1 |= 1UL << 21;
+		else
+			dmfc_gen1 &= ~(1UL << 21);
+	} else if (dma_chan == 28) { /*1*/
+		if (dmfc_size_28 / width > 2)
+			dmfc_gen1 |= 1UL << 16;
+		else
+			dmfc_gen1 &= ~(1UL << 16);
+	} else if (dma_chan == 29) { /*6F*/
+		if (dmfc_size_29 / width > 1)
+			dmfc_gen1 |= 1UL << 23;
+		else
+			dmfc_gen1 &= ~(1UL << 23);
+	}
+
+	__raw_writel(dmfc_gen1, DMFC_GENERAL1);
+}
+
+static void ipu_di_data_wave_config(int di,
+				     int wave_gen,
+				     int access_size, int component_size)
+{
+	u32 reg;
+	reg = (access_size << DI_DW_GEN_ACCESS_SIZE_OFFSET) |
+	    (component_size << DI_DW_GEN_COMPONENT_SIZE_OFFSET);
+	__raw_writel(reg, DI_DW_GEN(di, wave_gen));
+}
+
+static void ipu_di_data_pin_config(int di, int wave_gen, int di_pin, int set,
+				    int up, int down)
+{
+	u32 reg;
+
+	reg = __raw_readl(DI_DW_GEN(di, wave_gen));
+	reg &= ~(0x3 << (di_pin * 2));
+	reg |= set << (di_pin * 2);
+	__raw_writel(reg, DI_DW_GEN(di, wave_gen));
+
+	__raw_writel((down << 16) | up, DI_DW_SET(di, wave_gen, set));
+}
+
+static void ipu_di_sync_config(int di, int wave_gen,
+				int run_count, int run_src,
+				int offset_count, int offset_src,
+				int repeat_count, int cnt_clr_src,
+				int cnt_polarity_gen_en,
+				int cnt_polarity_clr_src,
+				int cnt_polarity_trigger_src,
+				int cnt_up, int cnt_down)
+{
+	u32 reg;
+
+	if ((run_count >= 0x1000) || (offset_count >= 0x1000) ||
+		(repeat_count >= 0x1000) ||
+		(cnt_up >= 0x400) || (cnt_down >= 0x400)) {
+		printf("DI%d counters out of range.\n", di);
+		return;
+	}
+
+	reg = (run_count << 19) | (++run_src << 16) |
+	    (offset_count << 3) | ++offset_src;
+	__raw_writel(reg, DI_SW_GEN0(di, wave_gen));
+	reg = (cnt_polarity_gen_en << 29) | (++cnt_clr_src << 25) |
+	    (++cnt_polarity_trigger_src << 12) | (++cnt_polarity_clr_src << 9);
+	reg |= (cnt_down << 16) | cnt_up;
+	if (repeat_count == 0) {
+		/* Enable auto reload */
+		reg |= 0x10000000;
+	}
+	__raw_writel(reg, DI_SW_GEN1(di, wave_gen));
+	reg = __raw_readl(DI_STP_REP(di, wave_gen));
+	reg &= ~(0xFFFF << (16 * ((wave_gen - 1) & 0x1)));
+	reg |= repeat_count << (16 * ((wave_gen - 1) & 0x1));
+	__raw_writel(reg, DI_STP_REP(di, wave_gen));
+}
+
+static void ipu_dc_map_config(int map, int byte_num, int offset, int mask)
+{
+	int ptr = map * 3 + byte_num;
+	u32 reg;
+
+	reg = __raw_readl(DC_MAP_CONF_VAL(ptr));
+	reg &= ~(0xFFFF << (16 * (ptr & 0x1)));
+	reg |= ((offset << 8) | mask) << (16 * (ptr & 0x1));
+	__raw_writel(reg, DC_MAP_CONF_VAL(ptr));
+
+	reg = __raw_readl(DC_MAP_CONF_PTR(map));
+	reg &= ~(0x1F << ((16 * (map & 0x1)) + (5 * byte_num)));
+	reg |= ptr << ((16 * (map & 0x1)) + (5 * byte_num));
+	__raw_writel(reg, DC_MAP_CONF_PTR(map));
+}
+
+static void ipu_dc_map_clear(int map)
+{
+	u32 reg = __raw_readl(DC_MAP_CONF_PTR(map));
+	__raw_writel(reg & ~(0xFFFF << (16 * (map & 0x1))),
+		     DC_MAP_CONF_PTR(map));
+}
+
+static void ipu_dc_write_tmpl(int word, u32 opcode, u32 operand, int map,
+			       int wave, int glue, int sync)
+{
+	u32 reg;
+	int stop = 1;
+
+	reg = sync;
+	reg |= (glue << 4);
+	reg |= (++wave << 11);
+	reg |= (++map << 15);
+	reg |= (operand << 20) & 0xFFF00000;
+	__raw_writel(reg, ipu_dc_tmpl_reg + word * 2);
+
+	reg = (operand >> 12);
+	reg |= opcode << 4;
+	reg |= (stop << 9);
+	__raw_writel(reg, ipu_dc_tmpl_reg + word * 2 + 1);
+}
+
+static void ipu_dc_link_event(int chan, int event, int addr, int priority)
+{
+	u32 reg;
+
+	reg = __raw_readl(DC_RL_CH(chan, event));
+	reg &= ~(0xFFFF << (16 * (event & 0x1)));
+	reg |= ((addr << 8) | priority) << (16 * (event & 0x1));
+	__raw_writel(reg, DC_RL_CH(chan, event));
+}
+
+/* Y = R *  1.200 + G *  2.343 + B *  .453 + 0.250;
+ * U = R * -.672 + G * -1.328 + B *  2.000 + 512.250.;
+ * V = R *  2.000 + G * -1.672 + B * -.328 + 512.250.;
+ */
+static const int rgb2ycbcr_coeff[5][3] = {
+	{0x4D, 0x96, 0x1D},
+	{0x3D5, 0x3AB, 0x80},
+	{0x80, 0x395, 0x3EB},
+	{0x0000, 0x0200, 0x0200},	/* B0, B1, B2 */
+	{0x2, 0x2, 0x2},	/* S0, S1, S2 */
+};
+
+/* R = (1.164 * (Y - 16)) + (1.596 * (Cr - 128));
+ * G = (1.164 * (Y - 16)) - (0.392 * (Cb - 128)) - (0.813 * (Cr - 128));
+ * B = (1.164 * (Y - 16)) + (2.017 * (Cb - 128);
+ */
+static const int ycbcr2rgb_coeff[5][3] = {
+	{0x095, 0x000, 0x0CC},
+	{0x095, 0x3CE, 0x398},
+	{0x095, 0x0FF, 0x000},
+	{0x3E42, 0x010A, 0x3DD6},	/*B0,B1,B2 */
+	{0x1, 0x1, 0x1},	/*S0,S1,S2 */
+};
+
+#define mask_a(a) ((u32)(a) & 0x3FF)
+#define mask_b(b) ((u32)(b) & 0x3FFF)
+
+/* Pls keep S0, S1 and S2 as 0x2 by using this convertion */
+static int rgb_to_yuv(int n, int red, int green, int blue)
+{
+	int c;
+	c = red * rgb2ycbcr_coeff[n][0];
+	c += green * rgb2ycbcr_coeff[n][1];
+	c += blue * rgb2ycbcr_coeff[n][2];
+	c /= 16;
+	c += rgb2ycbcr_coeff[3][n] * 4;
+	c += 8;
+	c /= 16;
+	if (c < 0)
+		c = 0;
+	if (c > 255)
+		c = 255;
+	return c;
+}
+
+/*
+ * Row is for BG:	RGB2YUV YUV2RGB RGB2RGB YUV2YUV CSC_NONE
+ * Column is for FG:	RGB2YUV YUV2RGB RGB2RGB YUV2YUV CSC_NONE
+ */
+static struct dp_csc_param_t dp_csc_array[CSC_NUM][CSC_NUM] = {
+	{
+		{DP_COM_CONF_CSC_DEF_BOTH, &rgb2ycbcr_coeff},
+		{0, 0},
+		{0, 0},
+		{DP_COM_CONF_CSC_DEF_BG, &rgb2ycbcr_coeff},
+		{DP_COM_CONF_CSC_DEF_BG, &rgb2ycbcr_coeff}
+	},
+	{
+		{0, 0},
+		{DP_COM_CONF_CSC_DEF_BOTH, &ycbcr2rgb_coeff},
+		{DP_COM_CONF_CSC_DEF_BG, &ycbcr2rgb_coeff},
+		{0, 0},
+		{DP_COM_CONF_CSC_DEF_BG, &ycbcr2rgb_coeff}
+	},
+	{
+		{0, 0},
+		{DP_COM_CONF_CSC_DEF_FG, &ycbcr2rgb_coeff},
+		{0, 0},
+		{0, 0},
+		{0, 0}
+	},
+	{
+		{DP_COM_CONF_CSC_DEF_FG, &rgb2ycbcr_coeff},
+		{0, 0},
+		{0, 0},
+		{0, 0},
+		{0, 0}
+	},
+	{
+		{DP_COM_CONF_CSC_DEF_FG, &rgb2ycbcr_coeff},
+		{DP_COM_CONF_CSC_DEF_FG, &ycbcr2rgb_coeff},
+		{0, 0},
+		{0, 0},
+		{0, 0}
+	}
+};
+
+static enum csc_type_t fg_csc_type = CSC_NONE, bg_csc_type = CSC_NONE;
+static int color_key_4rgb = 1;
+
+void ipu_dp_csc_setup(int dp, struct dp_csc_param_t dp_csc_param,
+			unsigned char srm_mode_update)
+{
+	u32 reg;
+	const int (*coeff)[5][3];
+
+	if (dp_csc_param.mode >= 0) {
+		reg = __raw_readl(DP_COM_CONF(dp));
+		reg &= ~DP_COM_CONF_CSC_DEF_MASK;
+		reg |= dp_csc_param.mode;
+		__raw_writel(reg, DP_COM_CONF(dp));
+	}
+
+	coeff = dp_csc_param.coeff;
+
+	if (coeff) {
+		__raw_writel(mask_a((*coeff)[0][0]) |
+				(mask_a((*coeff)[0][1]) << 16), DP_CSC_A_0(dp));
+		__raw_writel(mask_a((*coeff)[0][2]) |
+				(mask_a((*coeff)[1][0]) << 16), DP_CSC_A_1(dp));
+		__raw_writel(mask_a((*coeff)[1][1]) |
+				(mask_a((*coeff)[1][2]) << 16), DP_CSC_A_2(dp));
+		__raw_writel(mask_a((*coeff)[2][0]) |
+				(mask_a((*coeff)[2][1]) << 16), DP_CSC_A_3(dp));
+		__raw_writel(mask_a((*coeff)[2][2]) |
+				(mask_b((*coeff)[3][0]) << 16) |
+				((*coeff)[4][0] << 30), DP_CSC_0(dp));
+		__raw_writel(mask_b((*coeff)[3][1]) | ((*coeff)[4][1] << 14) |
+				(mask_b((*coeff)[3][2]) << 16) |
+				((*coeff)[4][2] << 30), DP_CSC_1(dp));
+	}
+
+	if (srm_mode_update) {
+		reg = __raw_readl(IPU_SRM_PRI2) | 0x8;
+		__raw_writel(reg, IPU_SRM_PRI2);
+	}
+}
+
+int ipu_dp_init(ipu_channel_t channel, uint32_t in_pixel_fmt,
+		 uint32_t out_pixel_fmt)
+{
+	int in_fmt, out_fmt;
+	int dp;
+	int partial = 0;
+	uint32_t reg;
+
+	if (channel == MEM_FG_SYNC) {
+		dp = DP_SYNC;
+		partial = 1;
+	} else if (channel == MEM_BG_SYNC) {
+		dp = DP_SYNC;
+		partial = 0;
+	} else if (channel == MEM_BG_ASYNC0) {
+		dp = DP_ASYNC0;
+		partial = 0;
+	} else {
+		return -EINVAL;
+	}
+
+	in_fmt = format_to_colorspace(in_pixel_fmt);
+	out_fmt = format_to_colorspace(out_pixel_fmt);
+
+	if (partial) {
+		if (in_fmt == RGB) {
+			if (out_fmt == RGB)
+				fg_csc_type = RGB2RGB;
+			else
+				fg_csc_type = RGB2YUV;
+		} else {
+			if (out_fmt == RGB)
+				fg_csc_type = YUV2RGB;
+			else
+				fg_csc_type = YUV2YUV;
+		}
+	} else {
+		if (in_fmt == RGB) {
+			if (out_fmt == RGB)
+				bg_csc_type = RGB2RGB;
+			else
+				bg_csc_type = RGB2YUV;
+		} else {
+			if (out_fmt == RGB)
+				bg_csc_type = YUV2RGB;
+			else
+				bg_csc_type = YUV2YUV;
+		}
+	}
+
+	/* Transform color key from rgb to yuv if CSC is enabled */
+	reg = __raw_readl(DP_COM_CONF(dp));
+	if (color_key_4rgb && (reg & DP_COM_CONF_GWCKE) &&
+		(((fg_csc_type == RGB2YUV) && (bg_csc_type == YUV2YUV)) ||
+		((fg_csc_type == YUV2YUV) && (bg_csc_type == RGB2YUV)) ||
+		((fg_csc_type == YUV2YUV) && (bg_csc_type == YUV2YUV)) ||
+		((fg_csc_type == YUV2RGB) && (bg_csc_type == YUV2RGB)))) {
+		int red, green, blue;
+		int y, u, v;
+		uint32_t color_key = __raw_readl(DP_GRAPH_WIND_CTRL(dp)) &
+			0xFFFFFFL;
+
+		debug("_ipu_dp_init color key 0x%x need change to yuv fmt!\n",
+			color_key);
+
+		red = (color_key >> 16) & 0xFF;
+		green = (color_key >> 8) & 0xFF;
+		blue = color_key & 0xFF;
+
+		y = rgb_to_yuv(0, red, green, blue);
+		u = rgb_to_yuv(1, red, green, blue);
+		v = rgb_to_yuv(2, red, green, blue);
+		color_key = (y << 16) | (u << 8) | v;
+
+		reg = __raw_readl(DP_GRAPH_WIND_CTRL(dp)) & 0xFF000000L;
+		__raw_writel(reg | color_key, DP_GRAPH_WIND_CTRL(dp));
+		color_key_4rgb = 0;
+
+		debug("_ipu_dp_init color key change to yuv fmt 0x%x!\n",
+			color_key);
+	}
+
+	ipu_dp_csc_setup(dp, dp_csc_array[bg_csc_type][fg_csc_type], 1);
+
+	return 0;
+}
+
+void ipu_dp_uninit(ipu_channel_t channel)
+{
+	int dp;
+	int partial = 0;
+
+	if (channel == MEM_FG_SYNC) {
+		dp = DP_SYNC;
+		partial = 1;
+	} else if (channel == MEM_BG_SYNC) {
+		dp = DP_SYNC;
+		partial = 0;
+	} else if (channel == MEM_BG_ASYNC0) {
+		dp = DP_ASYNC0;
+		partial = 0;
+	} else {
+		return;
+	}
+
+	if (partial)
+		fg_csc_type = CSC_NONE;
+	else
+		bg_csc_type = CSC_NONE;
+
+	ipu_dp_csc_setup(dp, dp_csc_array[bg_csc_type][fg_csc_type], 0);
+}
+
+void ipu_dc_init(int dc_chan, int di, unsigned char interlaced)
+{
+	u32 reg = 0;
+
+	if ((dc_chan == 1) || (dc_chan == 5)) {
+		if (interlaced) {
+			ipu_dc_link_event(dc_chan, DC_EVT_NL, 0, 3);
+			ipu_dc_link_event(dc_chan, DC_EVT_EOL, 0, 2);
+			ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA, 0, 1);
+		} else {
+			if (di) {
+				ipu_dc_link_event(dc_chan, DC_EVT_NL, 2, 3);
+				ipu_dc_link_event(dc_chan, DC_EVT_EOL, 3, 2);
+				ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA,
+					4, 1);
+			} else {
+				ipu_dc_link_event(dc_chan, DC_EVT_NL, 5, 3);
+				ipu_dc_link_event(dc_chan, DC_EVT_EOL, 6, 2);
+				ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA,
+					7, 1);
+			}
+		}
+		ipu_dc_link_event(dc_chan, DC_EVT_NF, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NFIELD, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_EOF, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_EOFIELD, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_CHAN, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_ADDR, 0, 0);
+
+		reg = 0x2;
+		reg |= DC_DISP_ID_SYNC(di) << DC_WR_CH_CONF_PROG_DISP_ID_OFFSET;
+		reg |= di << 2;
+		if (interlaced)
+			reg |= DC_WR_CH_CONF_FIELD_MODE;
+	} else if ((dc_chan == 8) || (dc_chan == 9)) {
+		/* async channels */
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA_W_0, 0x64, 1);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA_W_1, 0x64, 1);
+
+		reg = 0x3;
+		reg |= DC_DISP_ID_SERIAL << DC_WR_CH_CONF_PROG_DISP_ID_OFFSET;
+	}
+	__raw_writel(reg, DC_WR_CH_CONF(dc_chan));
+
+	__raw_writel(0x00000000, DC_WR_CH_ADDR(dc_chan));
+
+	__raw_writel(0x00000084, DC_GEN);
+}
+
+void ipu_dc_uninit(int dc_chan)
+{
+	if ((dc_chan == 1) || (dc_chan == 5)) {
+		ipu_dc_link_event(dc_chan, DC_EVT_NL, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_EOL, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NF, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NFIELD, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_EOF, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_EOFIELD, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_CHAN, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_ADDR, 0, 0);
+	} else if ((dc_chan == 8) || (dc_chan == 9)) {
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_ADDR_W_0, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_ADDR_W_1, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_CHAN_W_0, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_CHAN_W_1, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA_W_0, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA_W_1, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_ADDR_R_0, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_ADDR_R_1, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_CHAN_R_0, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_CHAN_R_1, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA_R_0, 0, 0);
+		ipu_dc_link_event(dc_chan, DC_EVT_NEW_DATA_R_1, 0, 0);
+	}
+}
+
+int ipu_chan_is_interlaced(ipu_channel_t channel)
+{
+	if (channel == MEM_DC_SYNC)
+		return !!(__raw_readl(DC_WR_CH_CONF_1) &
+			  DC_WR_CH_CONF_FIELD_MODE);
+	else if ((channel == MEM_BG_SYNC) || (channel == MEM_FG_SYNC))
+		return !!(__raw_readl(DC_WR_CH_CONF_5) &
+			  DC_WR_CH_CONF_FIELD_MODE);
+	return 0;
+}
+
+void ipu_dp_dc_enable(ipu_channel_t channel)
+{
+	int di;
+	uint32_t reg;
+	uint32_t dc_chan;
+
+	if (channel == MEM_FG_SYNC)
+		dc_chan = 5;
+	if (channel == MEM_DC_SYNC)
+		dc_chan = 1;
+	else if (channel == MEM_BG_SYNC)
+		dc_chan = 5;
+	else
+		return;
+
+	if (channel == MEM_FG_SYNC) {
+		/* Enable FG channel */
+		reg = __raw_readl(DP_COM_CONF(DP_SYNC));
+		__raw_writel(reg | DP_COM_CONF_FG_EN, DP_COM_CONF(DP_SYNC));
+
+		reg = __raw_readl(IPU_SRM_PRI2) | 0x8;
+		__raw_writel(reg, IPU_SRM_PRI2);
+		return;
+	}
+
+	di = g_dc_di_assignment[dc_chan];
+
+	/* Make sure other DC sync channel is not assigned same DI */
+	reg = __raw_readl(DC_WR_CH_CONF(6 - dc_chan));
+	if ((di << 2) == (reg & DC_WR_CH_CONF_PROG_DI_ID)) {
+		reg &= ~DC_WR_CH_CONF_PROG_DI_ID;
+		reg |= di ? 0 : DC_WR_CH_CONF_PROG_DI_ID;
+		__raw_writel(reg, DC_WR_CH_CONF(6 - dc_chan));
+	}
+
+	reg = __raw_readl(DC_WR_CH_CONF(dc_chan));
+	reg |= 4 << DC_WR_CH_CONF_PROG_TYPE_OFFSET;
+	__raw_writel(reg, DC_WR_CH_CONF(dc_chan));
+
+	clk_enable(g_pixel_clk[di]);
+}
+
+static unsigned char dc_swap;
+
+void ipu_dp_dc_disable(ipu_channel_t channel, unsigned char swap)
+{
+	uint32_t reg;
+	uint32_t csc;
+	uint32_t dc_chan = 0;
+	int timeout = 50;
+
+	dc_swap = swap;
+
+	if (channel == MEM_DC_SYNC) {
+		dc_chan = 1;
+	} else if (channel == MEM_BG_SYNC) {
+		dc_chan = 5;
+	} else if (channel == MEM_FG_SYNC) {
+		/* Disable FG channel */
+		dc_chan = 5;
+
+		reg = __raw_readl(DP_COM_CONF(DP_SYNC));
+		csc = reg & DP_COM_CONF_CSC_DEF_MASK;
+		if (csc == DP_COM_CONF_CSC_DEF_FG)
+			reg &= ~DP_COM_CONF_CSC_DEF_MASK;
+
+		reg &= ~DP_COM_CONF_FG_EN;
+		__raw_writel(reg, DP_COM_CONF(DP_SYNC));
+
+		reg = __raw_readl(IPU_SRM_PRI2) | 0x8;
+		__raw_writel(reg, IPU_SRM_PRI2);
+
+		timeout = 50;
+
+		/*
+		 * Wait for DC triple buffer to empty,
+		 * this check is useful for tv overlay.
+		 */
+		if (g_dc_di_assignment[dc_chan] == 0)
+			while ((__raw_readl(DC_STAT) & 0x00000002)
+			       != 0x00000002) {
+				udelay(2000);
+				timeout -= 2;
+				if (timeout <= 0)
+					break;
+			}
+		else if (g_dc_di_assignment[dc_chan] == 1)
+			while ((__raw_readl(DC_STAT) & 0x00000020)
+			       != 0x00000020) {
+				udelay(2000);
+				timeout -= 2;
+				if (timeout <= 0)
+					break;
+			}
+		return;
+	} else {
+		return;
+	}
+
+	if (dc_swap) {
+		/* Swap DC channel 1 and 5 settings, and disable old dc chan */
+		reg = __raw_readl(DC_WR_CH_CONF(dc_chan));
+		__raw_writel(reg, DC_WR_CH_CONF(6 - dc_chan));
+		reg &= ~DC_WR_CH_CONF_PROG_TYPE_MASK;
+		reg ^= DC_WR_CH_CONF_PROG_DI_ID;
+		__raw_writel(reg, DC_WR_CH_CONF(dc_chan));
+	} else {
+		timeout = 50;
+
+		/* Wait for DC triple buffer to empty */
+		if (g_dc_di_assignment[dc_chan] == 0)
+			while ((__raw_readl(DC_STAT) & 0x00000002)
+				!= 0x00000002) {
+				udelay(2000);
+				timeout -= 2;
+				if (timeout <= 0)
+					break;
+			}
+		else if (g_dc_di_assignment[dc_chan] == 1)
+			while ((__raw_readl(DC_STAT) & 0x00000020)
+				!= 0x00000020) {
+				udelay(2000);
+				timeout -= 2;
+				if (timeout <= 0)
+					break;
+			}
+
+		reg = __raw_readl(DC_WR_CH_CONF(dc_chan));
+		reg &= ~DC_WR_CH_CONF_PROG_TYPE_MASK;
+		__raw_writel(reg, DC_WR_CH_CONF(dc_chan));
+
+		reg = __raw_readl(IPU_DISP_GEN);
+		if (g_dc_di_assignment[dc_chan])
+			reg &= ~DI1_COUNTER_RELEASE;
+		else
+			reg &= ~DI0_COUNTER_RELEASE;
+		__raw_writel(reg, IPU_DISP_GEN);
+
+		/* Clock is already off because it must be done quickly, but
+		   we need to fix the ref count */
+		clk_disable(g_pixel_clk[g_dc_di_assignment[dc_chan]]);
+	}
+}
+
+void ipu_init_dc_mappings(void)
+{
+	/* IPU_PIX_FMT_RGB24 */
+	ipu_dc_map_clear(0);
+	ipu_dc_map_config(0, 0, 7, 0xFF);
+	ipu_dc_map_config(0, 1, 15, 0xFF);
+	ipu_dc_map_config(0, 2, 23, 0xFF);
+
+	/* IPU_PIX_FMT_RGB666 */
+	ipu_dc_map_clear(1);
+	ipu_dc_map_config(1, 0, 5, 0xFC);
+	ipu_dc_map_config(1, 1, 11, 0xFC);
+	ipu_dc_map_config(1, 2, 17, 0xFC);
+
+	/* IPU_PIX_FMT_YUV444 */
+	ipu_dc_map_clear(2);
+	ipu_dc_map_config(2, 0, 15, 0xFF);
+	ipu_dc_map_config(2, 1, 23, 0xFF);
+	ipu_dc_map_config(2, 2, 7, 0xFF);
+
+	/* IPU_PIX_FMT_RGB565 */
+	ipu_dc_map_clear(3);
+	ipu_dc_map_config(3, 0, 4, 0xF8);
+	ipu_dc_map_config(3, 1, 10, 0xFC);
+	ipu_dc_map_config(3, 2, 15, 0xF8);
+
+	/* IPU_PIX_FMT_LVDS666 */
+	ipu_dc_map_clear(4);
+	ipu_dc_map_config(4, 0, 5, 0xFC);
+	ipu_dc_map_config(4, 1, 13, 0xFC);
+	ipu_dc_map_config(4, 2, 21, 0xFC);
+}
+
+int ipu_pixfmt_to_map(uint32_t fmt)
+{
+	switch (fmt) {
+	case IPU_PIX_FMT_GENERIC:
+	case IPU_PIX_FMT_RGB24:
+		return 0;
+	case IPU_PIX_FMT_RGB666:
+		return 1;
+	case IPU_PIX_FMT_YUV444:
+		return 2;
+	case IPU_PIX_FMT_RGB565:
+		return 3;
+	case IPU_PIX_FMT_LVDS666:
+		return 4;
+	}
+
+	return -1;
+}
+
+/*
+ * This function is called to adapt synchronous LCD panel to IPU restriction.
+ */
+void adapt_panel_to_ipu_restricitions(uint32_t *pixel_clk,
+				      uint16_t width, uint16_t height,
+				      uint16_t h_start_width,
+				      uint16_t h_end_width,
+				      uint16_t v_start_width,
+				      uint16_t *v_end_width)
+{
+	if (*v_end_width < 2) {
+		uint16_t total_width = width + h_start_width + h_end_width;
+		uint16_t total_height_old = height + v_start_width +
+			(*v_end_width);
+		uint16_t total_height_new = height + v_start_width + 2;
+		*v_end_width = 2;
+		*pixel_clk = (*pixel_clk) * total_width * total_height_new /
+			(total_width * total_height_old);
+		printf("WARNING: adapt panel end blank lines\n");
+	}
+}
+
+/*
+ * This function is called to initialize a synchronous LCD panel.
+ *
+ * @param       disp            The DI the panel is attached to.
+ *
+ * @param       pixel_clk       Desired pixel clock frequency in Hz.
+ *
+ * @param       pixel_fmt       Input parameter for pixel format of buffer.
+ *                              Pixel format is a FOURCC ASCII code.
+ *
+ * @param       width           The width of panel in pixels.
+ *
+ * @param       height          The height of panel in pixels.
+ *
+ * @param       hStartWidth     The number of pixel clocks between the HSYNC
+ *                              signal pulse and the start of valid data.
+ *
+ * @param       hSyncWidth      The width of the HSYNC signal in units of pixel
+ *                              clocks.
+ *
+ * @param       hEndWidth       The number of pixel clocks between the end of
+ *                              valid data and the HSYNC signal for next line.
+ *
+ * @param       vStartWidth     The number of lines between the VSYNC
+ *                              signal pulse and the start of valid data.
+ *
+ * @param       vSyncWidth      The width of the VSYNC signal in units of lines
+ *
+ * @param       vEndWidth       The number of lines between the end of valid
+ *                              data and the VSYNC signal for next frame.
+ *
+ * @param       sig             Bitfield of signal polarities for LCD interface.
+ *
+ * @return      This function returns 0 on success or negative error code on
+ *              fail.
+ */
+
+int32_t ipu_init_sync_panel(int disp, uint32_t pixel_clk,
+			    uint16_t width, uint16_t height,
+			    uint32_t pixel_fmt,
+			    uint16_t h_start_width, uint16_t h_sync_width,
+			    uint16_t h_end_width, uint16_t v_start_width,
+			    uint16_t v_sync_width, uint16_t v_end_width,
+			    uint32_t v_to_h_sync, ipu_di_signal_cfg_t sig)
+{
+	uint32_t reg;
+	uint32_t di_gen, vsync_cnt;
+	uint32_t div, rounded_pixel_clk;
+	uint32_t h_total, v_total;
+	int map;
+	struct clk *di_parent;
+
+	debug("panel size = %d x %d\n", width, height);
+
+	if ((v_sync_width == 0) || (h_sync_width == 0))
+		return EINVAL;
+
+	adapt_panel_to_ipu_restricitions(&pixel_clk, width, height,
+					 h_start_width, h_end_width,
+					 v_start_width, &v_end_width);
+	h_total = width + h_sync_width + h_start_width + h_end_width;
+	v_total = height + v_sync_width + v_start_width + v_end_width;
+
+	/* Init clocking */
+	debug("pixel clk = %d\n", pixel_clk);
+
+	if (sig.ext_clk) {
+		if (!(g_di1_tvout && (disp == 1))) { /*not round div for tvout*/
+			/*
+			 * Set the  PLL to be an even multiple
+			 * of the pixel clock.
+			 */
+			if ((clk_get_usecount(g_pixel_clk[0]) == 0) &&
+				(clk_get_usecount(g_pixel_clk[1]) == 0)) {
+				di_parent = clk_get_parent(g_di_clk[disp]);
+				rounded_pixel_clk =
+					clk_round_rate(g_pixel_clk[disp],
+						pixel_clk);
+				div  = clk_get_rate(di_parent) /
+					rounded_pixel_clk;
+				if (div % 2)
+					div++;
+				if (clk_get_rate(di_parent) != div *
+					rounded_pixel_clk)
+					clk_set_rate(di_parent,
+						div * rounded_pixel_clk);
+				udelay(10000);
+				clk_set_rate(g_di_clk[disp],
+					2 * rounded_pixel_clk);
+				udelay(10000);
+			}
+		}
+		clk_set_parent(g_pixel_clk[disp], g_di_clk[disp]);
+	} else {
+		if (clk_get_usecount(g_pixel_clk[disp]) != 0)
+			clk_set_parent(g_pixel_clk[disp], g_ipu_clk);
+	}
+	rounded_pixel_clk = clk_round_rate(g_pixel_clk[disp], pixel_clk);
+	clk_set_rate(g_pixel_clk[disp], rounded_pixel_clk);
+	udelay(5000);
+	/* Get integer portion of divider */
+	div = clk_get_rate(clk_get_parent(g_pixel_clk[disp])) /
+		rounded_pixel_clk;
+
+	ipu_di_data_wave_config(disp, SYNC_WAVE, div - 1, div - 1);
+	ipu_di_data_pin_config(disp, SYNC_WAVE, DI_PIN15, 3, 0, div * 2);
+
+	map = ipu_pixfmt_to_map(pixel_fmt);
+	if (map < 0) {
+		debug("IPU_DISP: No MAP\n");
+		return -EINVAL;
+	}
+
+	di_gen = __raw_readl(DI_GENERAL(disp));
+
+	if (sig.interlaced) {
+		/* Setup internal HSYNC waveform */
+		ipu_di_sync_config(
+				disp,		/* display */
+				1,		/* counter */
+				h_total / 2 - 1,/* run count */
+				DI_SYNC_CLK,	/* run_resolution */
+				0,		/* offset */
+				DI_SYNC_NONE,	/* offset resolution */
+				0,		/* repeat count */
+				DI_SYNC_NONE,	/* CNT_CLR_SEL */
+				0,		/* CNT_POLARITY_GEN_EN */
+				DI_SYNC_NONE,	/* CNT_POLARITY_CLR_SEL */
+				DI_SYNC_NONE,	/* CNT_POLARITY_TRIGGER_SEL */
+				0,		/* COUNT UP */
+				0		/* COUNT DOWN */
+				);
+
+		/* Field 1 VSYNC waveform */
+		ipu_di_sync_config(
+				disp,		/* display */
+				2,		/* counter */
+				h_total - 1,	/* run count */
+				DI_SYNC_CLK,	/* run_resolution */
+				0,		/* offset */
+				DI_SYNC_NONE,	/* offset resolution */
+				0,		/* repeat count */
+				DI_SYNC_NONE,	/* CNT_CLR_SEL */
+				0,		/* CNT_POLARITY_GEN_EN */
+				DI_SYNC_NONE,	/* CNT_POLARITY_CLR_SEL */
+				DI_SYNC_NONE,	/* CNT_POLARITY_TRIGGER_SEL */
+				0,		/* COUNT UP */
+				4		/* COUNT DOWN */
+				);
+
+		/* Setup internal HSYNC waveform */
+		ipu_di_sync_config(
+				disp,		/* display */
+				3,		/* counter */
+				v_total * 2 - 1,/* run count */
+				DI_SYNC_INT_HSYNC,	/* run_resolution */
+				1,		/* offset */
+				DI_SYNC_INT_HSYNC,	/* offset resolution */
+				0,		/* repeat count */
+				DI_SYNC_NONE,	/* CNT_CLR_SEL */
+				0,		/* CNT_POLARITY_GEN_EN */
+				DI_SYNC_NONE,	/* CNT_POLARITY_CLR_SEL */
+				DI_SYNC_NONE,	/* CNT_POLARITY_TRIGGER_SEL */
+				0,		/* COUNT UP */
+				4		/* COUNT DOWN */
+				);
+
+		/* Active Field ? */
+		ipu_di_sync_config(
+				disp,		/* display */
+				4,		/* counter */
+				v_total / 2 - 1,/* run count */
+				DI_SYNC_HSYNC,	/* run_resolution */
+				v_start_width,	/*  offset */
+				DI_SYNC_HSYNC,	/* offset resolution */
+				2,		/* repeat count */
+				DI_SYNC_VSYNC,	/* CNT_CLR_SEL */
+				0,		/* CNT_POLARITY_GEN_EN */
+				DI_SYNC_NONE,	/* CNT_POLARITY_CLR_SEL */
+				DI_SYNC_NONE,	/* CNT_POLARITY_TRIGGER_SEL */
+				0,		/* COUNT UP */
+				0		/* COUNT DOWN */
+				);
+
+		/* Active Line */
+		ipu_di_sync_config(
+				disp,		/* display */
+				5,		/* counter */
+				0,		/* run count */
+				DI_SYNC_HSYNC,	/* run_resolution */
+				0,		/*  offset */
+				DI_SYNC_NONE,	/* offset resolution */
+				height / 2,	/* repeat count */
+				4,		/* CNT_CLR_SEL */
+				0,		/* CNT_POLARITY_GEN_EN */
+				DI_SYNC_NONE,	/* CNT_POLARITY_CLR_SEL */
+				DI_SYNC_NONE,	/* CNT_POLARITY_TRIGGER_SEL */
+				0,		/* COUNT UP */
+				0		/* COUNT DOWN */
+				);
+
+		/* Field 0 VSYNC waveform */
+		ipu_di_sync_config(
+				disp,		/* display */
+				6,		/* counter */
+				v_total - 1,	/* run count */
+				DI_SYNC_HSYNC,	/* run_resolution */
+				0,		/* offset */
+				DI_SYNC_NONE,	/* offset resolution */
+				0,		/* repeat count */
+				DI_SYNC_NONE,	/* CNT_CLR_SEL  */
+				0,		/* CNT_POLARITY_GEN_EN */
+				DI_SYNC_NONE,	/* CNT_POLARITY_CLR_SEL */
+				DI_SYNC_NONE,	/* CNT_POLARITY_TRIGGER_SEL */
+				0,		/* COUNT UP */
+				0		/* COUNT DOWN */
+				);
+
+		/* DC VSYNC waveform */
+		vsync_cnt = 7;
+		ipu_di_sync_config(
+				disp,		/* display */
+				7,		/* counter */
+				v_total / 2 - 1,/* run count */
+				DI_SYNC_HSYNC,	/* run_resolution  */
+				9,		/* offset  */
+				DI_SYNC_HSYNC,	/* offset resolution */
+				2,		/* repeat count */
+				DI_SYNC_VSYNC,	/* CNT_CLR_SEL */
+				0,		/* CNT_POLARITY_GEN_EN */
+				DI_SYNC_NONE,	/* CNT_POLARITY_CLR_SEL */
+				DI_SYNC_NONE,	/* CNT_POLARITY_TRIGGER_SEL */
+				0,		/* COUNT UP */
+				0		/* COUNT DOWN */
+				);
+
+		/* active pixel waveform */
+		ipu_di_sync_config(
+				disp,		/* display */
+				8,		/* counter */
+				0,		/* run count  */
+				DI_SYNC_CLK,	/* run_resolution */
+				h_start_width,	/* offset  */
+				DI_SYNC_CLK,	/* offset resolution */
+				width,		/* repeat count  */
+				5,		/* CNT_CLR_SEL  */
+				0,		/* CNT_POLARITY_GEN_EN  */
+				DI_SYNC_NONE,	/* CNT_POLARITY_CLR_SEL */
+				DI_SYNC_NONE,	/* CNT_POLARITY_TRIGGER_SEL  */
+				0,		/* COUNT UP  */
+				0		/* COUNT DOWN */
+				);
+
+		ipu_di_sync_config(
+				disp,		/* display */
+				9,		/* counter */
+				v_total - 1,	/* run count */
+				DI_SYNC_INT_HSYNC,/* run_resolution */
+				v_total / 2,	/* offset  */
+				DI_SYNC_INT_HSYNC,/* offset resolution  */
+				0,		/* repeat count */
+				DI_SYNC_HSYNC,	/* CNT_CLR_SEL */
+				0,		/* CNT_POLARITY_GEN_EN  */
+				DI_SYNC_NONE,	/* CNT_POLARITY_CLR_SEL  */
+				DI_SYNC_NONE,	/* CNT_POLARITY_TRIGGER_SEL */
+				0,		/* COUNT UP */
+				4		/* COUNT DOWN */
+				);
+
+		/* set gentime select and tag sel */
+		reg = __raw_readl(DI_SW_GEN1(disp, 9));
+		reg &= 0x1FFFFFFF;
+		reg |= (3 - 1)<<29 | 0x00008000;
+		__raw_writel(reg, DI_SW_GEN1(disp, 9));
+
+		__raw_writel(v_total / 2 - 1, DI_SCR_CONF(disp));
+
+		/* set y_sel = 1 */
+		di_gen |= 0x10000000;
+		di_gen |= DI_GEN_POLARITY_5;
+		di_gen |= DI_GEN_POLARITY_8;
+	} else {
+		/* Setup internal HSYNC waveform */
+		ipu_di_sync_config(disp, 1, h_total - 1, DI_SYNC_CLK,
+				0, DI_SYNC_NONE, 0, DI_SYNC_NONE,
+				0, DI_SYNC_NONE,
+				DI_SYNC_NONE, 0, 0);
+
+		/* Setup external (delayed) HSYNC waveform */
+		ipu_di_sync_config(disp, DI_SYNC_HSYNC, h_total - 1,
+				DI_SYNC_CLK, div * v_to_h_sync, DI_SYNC_CLK,
+				0, DI_SYNC_NONE, 1, DI_SYNC_NONE,
+				DI_SYNC_CLK, 0, h_sync_width * 2);
+		/* Setup VSYNC waveform */
+		vsync_cnt = DI_SYNC_VSYNC;
+		ipu_di_sync_config(disp, DI_SYNC_VSYNC, v_total - 1,
+				DI_SYNC_INT_HSYNC, 0, DI_SYNC_NONE, 0,
+				DI_SYNC_NONE, 1, DI_SYNC_NONE,
+				DI_SYNC_INT_HSYNC, 0, v_sync_width * 2);
+		__raw_writel(v_total - 1, DI_SCR_CONF(disp));
+
+		/* Setup active data waveform to sync with DC */
+		ipu_di_sync_config(disp, 4, 0, DI_SYNC_HSYNC,
+				v_sync_width + v_start_width, DI_SYNC_HSYNC,
+				height,
+				DI_SYNC_VSYNC, 0, DI_SYNC_NONE,
+				DI_SYNC_NONE, 0, 0);
+		ipu_di_sync_config(disp, 5, 0, DI_SYNC_CLK,
+				h_sync_width + h_start_width, DI_SYNC_CLK,
+				width, 4, 0, DI_SYNC_NONE, DI_SYNC_NONE, 0,
+				0);
+
+		/* reset all unused counters */
+		__raw_writel(0, DI_SW_GEN0(disp, 6));
+		__raw_writel(0, DI_SW_GEN1(disp, 6));
+		__raw_writel(0, DI_SW_GEN0(disp, 7));
+		__raw_writel(0, DI_SW_GEN1(disp, 7));
+		__raw_writel(0, DI_SW_GEN0(disp, 8));
+		__raw_writel(0, DI_SW_GEN1(disp, 8));
+		__raw_writel(0, DI_SW_GEN0(disp, 9));
+		__raw_writel(0, DI_SW_GEN1(disp, 9));
+
+		reg = __raw_readl(DI_STP_REP(disp, 6));
+		reg &= 0x0000FFFF;
+		__raw_writel(reg, DI_STP_REP(disp, 6));
+		__raw_writel(0, DI_STP_REP(disp, 7));
+		__raw_writel(0, DI_STP_REP(disp, 9));
+
+		/* Init template microcode */
+		if (disp) {
+		   ipu_dc_write_tmpl(2, WROD(0), 0, map, SYNC_WAVE, 8, 5);
+		   ipu_dc_write_tmpl(3, WROD(0), 0, map, SYNC_WAVE, 4, 5);
+		   ipu_dc_write_tmpl(4, WROD(0), 0, map, SYNC_WAVE, 0, 5);
+		} else {
+		   ipu_dc_write_tmpl(5, WROD(0), 0, map, SYNC_WAVE, 8, 5);
+		   ipu_dc_write_tmpl(6, WROD(0), 0, map, SYNC_WAVE, 4, 5);
+		   ipu_dc_write_tmpl(7, WROD(0), 0, map, SYNC_WAVE, 0, 5);
+		}
+
+		if (sig.Hsync_pol)
+			di_gen |= DI_GEN_POLARITY_2;
+		if (sig.Vsync_pol)
+			di_gen |= DI_GEN_POLARITY_3;
+
+		if (sig.clk_pol)
+			di_gen |= DI_GEN_POL_CLK;
+
+	}
+
+	__raw_writel(di_gen, DI_GENERAL(disp));
+
+	__raw_writel((--vsync_cnt << DI_VSYNC_SEL_OFFSET) |
+			0x00000002, DI_SYNC_AS_GEN(disp));
+
+	reg = __raw_readl(DI_POL(disp));
+	reg &= ~(DI_POL_DRDY_DATA_POLARITY | DI_POL_DRDY_POLARITY_15);
+	if (sig.enable_pol)
+		reg |= DI_POL_DRDY_POLARITY_15;
+	if (sig.data_pol)
+		reg |= DI_POL_DRDY_DATA_POLARITY;
+	__raw_writel(reg, DI_POL(disp));
+
+	__raw_writel(width, DC_DISP_CONF2(DC_DISP_ID_SYNC(disp)));
+
+	return 0;
+}
+
+/*
+ * This function sets the foreground and background plane global alpha blending
+ * modes. This function also sets the DP graphic plane according to the
+ * parameter of IPUv3 DP channel.
+ *
+ * @param	channel		IPUv3 DP channel
+ *
+ * @param       enable          Boolean to enable or disable global alpha
+ *                              blending. If disabled, local blending is used.
+ *
+ * @param       alpha           Global alpha value.
+ *
+ * @return      Returns 0 on success or negative error code on fail
+ */
+int32_t ipu_disp_set_global_alpha(ipu_channel_t channel, unsigned char enable,
+				  uint8_t alpha)
+{
+	uint32_t reg;
+	uint32_t flow;
+
+	unsigned char bg_chan;
+
+	if (channel == MEM_BG_SYNC || channel == MEM_FG_SYNC)
+		flow = DP_SYNC;
+	else if (channel == MEM_BG_ASYNC0 || channel == MEM_FG_ASYNC0)
+		flow = DP_ASYNC0;
+	else if (channel == MEM_BG_ASYNC1 || channel == MEM_FG_ASYNC1)
+		flow = DP_ASYNC1;
+	else
+		return -EINVAL;
+
+	if (channel == MEM_BG_SYNC || channel == MEM_BG_ASYNC0 ||
+	    channel == MEM_BG_ASYNC1)
+		bg_chan = 1;
+	else
+		bg_chan = 0;
+
+	if (!g_ipu_clk_enabled)
+		clk_enable(g_ipu_clk);
+
+	if (bg_chan) {
+		reg = __raw_readl(DP_COM_CONF(flow));
+		__raw_writel(reg & ~DP_COM_CONF_GWSEL, DP_COM_CONF(flow));
+	} else {
+		reg = __raw_readl(DP_COM_CONF(flow));
+		__raw_writel(reg | DP_COM_CONF_GWSEL, DP_COM_CONF(flow));
+	}
+
+	if (enable) {
+		reg = __raw_readl(DP_GRAPH_WIND_CTRL(flow)) & 0x00FFFFFFL;
+		__raw_writel(reg | ((uint32_t) alpha << 24),
+			     DP_GRAPH_WIND_CTRL(flow));
+
+		reg = __raw_readl(DP_COM_CONF(flow));
+		__raw_writel(reg | DP_COM_CONF_GWAM, DP_COM_CONF(flow));
+	} else {
+		reg = __raw_readl(DP_COM_CONF(flow));
+		__raw_writel(reg & ~DP_COM_CONF_GWAM, DP_COM_CONF(flow));
+	}
+
+	reg = __raw_readl(IPU_SRM_PRI2) | 0x8;
+	__raw_writel(reg, IPU_SRM_PRI2);
+
+	if (!g_ipu_clk_enabled)
+		clk_disable(g_ipu_clk);
+
+	return 0;
+}
+
+/*
+ * This function sets the transparent color key for SDC graphic plane.
+ *
+ * @param       channel         Input parameter for the logical channel ID.
+ *
+ * @param       enable          Boolean to enable or disable color key
+ *
+ * @param       colorKey        24-bit RGB color for transparent color key.
+ *
+ * @return      Returns 0 on success or negative error code on fail
+ */
+int32_t ipu_disp_set_color_key(ipu_channel_t channel, unsigned char enable,
+			       uint32_t color_key)
+{
+	uint32_t reg, flow;
+	int y, u, v;
+	int red, green, blue;
+
+	if (channel == MEM_BG_SYNC || channel == MEM_FG_SYNC)
+		flow = DP_SYNC;
+	else if (channel == MEM_BG_ASYNC0 || channel == MEM_FG_ASYNC0)
+		flow = DP_ASYNC0;
+	else if (channel == MEM_BG_ASYNC1 || channel == MEM_FG_ASYNC1)
+		flow = DP_ASYNC1;
+	else
+		return -EINVAL;
+
+	if (!g_ipu_clk_enabled)
+		clk_enable(g_ipu_clk);
+
+	color_key_4rgb = 1;
+	/* Transform color key from rgb to yuv if CSC is enabled */
+	if (((fg_csc_type == RGB2YUV) && (bg_csc_type == YUV2YUV)) ||
+		((fg_csc_type == YUV2YUV) && (bg_csc_type == RGB2YUV)) ||
+		((fg_csc_type == YUV2YUV) && (bg_csc_type == YUV2YUV)) ||
+		((fg_csc_type == YUV2RGB) && (bg_csc_type == YUV2RGB))) {
+
+		debug("color key 0x%x need change to yuv fmt\n", color_key);
+
+		red = (color_key >> 16) & 0xFF;
+		green = (color_key >> 8) & 0xFF;
+		blue = color_key & 0xFF;
+
+		y = rgb_to_yuv(0, red, green, blue);
+		u = rgb_to_yuv(1, red, green, blue);
+		v = rgb_to_yuv(2, red, green, blue);
+		color_key = (y << 16) | (u << 8) | v;
+
+		color_key_4rgb = 0;
+
+		debug("color key change to yuv fmt 0x%x\n", color_key);
+	}
+
+	if (enable) {
+		reg = __raw_readl(DP_GRAPH_WIND_CTRL(flow)) & 0xFF000000L;
+		__raw_writel(reg | color_key, DP_GRAPH_WIND_CTRL(flow));
+
+		reg = __raw_readl(DP_COM_CONF(flow));
+		__raw_writel(reg | DP_COM_CONF_GWCKE, DP_COM_CONF(flow));
+	} else {
+		reg = __raw_readl(DP_COM_CONF(flow));
+		__raw_writel(reg & ~DP_COM_CONF_GWCKE, DP_COM_CONF(flow));
+	}
+
+	reg = __raw_readl(IPU_SRM_PRI2) | 0x8;
+	__raw_writel(reg, IPU_SRM_PRI2);
+
+	if (!g_ipu_clk_enabled)
+		clk_disable(g_ipu_clk);
+
+	return 0;
+}
diff --git a/drivers/video/ipu_regs.h b/drivers/video/ipu_regs.h
new file mode 100644
index 0000000..36f07bb
--- /dev/null
+++ b/drivers/video/ipu_regs.h
@@ -0,0 +1,418 @@
+/*
+ * Porting to u-boot:
+ *
+ * (C) Copyright 2010
+ * Stefano Babic, DENX Software Engineering, sbabic@denx.de
+ *
+ * Linux IPU driver for MX51:
+ *
+ * (C) Copyright 2005-2009 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __IPU_REGS_INCLUDED__
+#define __IPU_REGS_INCLUDED__
+
+#define IPU_DISP0_BASE		0x00000000
+#define IPU_MCU_T_DEFAULT	8
+#define IPU_DISP1_BASE		(IPU_MCU_T_DEFAULT << 25)
+#define IPU_CM_REG_BASE		0x1E000000
+#define IPU_STAT_REG_BASE	0x1E000200
+#define IPU_IDMAC_REG_BASE	0x1E008000
+#define IPU_ISP_REG_BASE	0x1E010000
+#define IPU_DP_REG_BASE		0x1E018000
+#define IPU_IC_REG_BASE		0x1E020000
+#define IPU_IRT_REG_BASE	0x1E028000
+#define IPU_CSI0_REG_BASE	0x1E030000
+#define IPU_CSI1_REG_BASE	0x1E038000
+#define IPU_DI0_REG_BASE	0x1E040000
+#define IPU_DI1_REG_BASE	0x1E048000
+#define IPU_SMFC_REG_BASE	0x1E050000
+#define IPU_DC_REG_BASE		0x1E058000
+#define IPU_DMFC_REG_BASE	0x1E060000
+#define IPU_CPMEM_REG_BASE	0x1F000000
+#define IPU_LUT_REG_BASE	0x1F020000
+#define IPU_SRM_REG_BASE	0x1F040000
+#define IPU_TPM_REG_BASE	0x1F060000
+#define IPU_DC_TMPL_REG_BASE	0x1F080000
+#define IPU_ISP_TBPR_REG_BASE	0x1F0C0000
+#define IPU_VDI_REG_BASE	0x1E068000
+
+
+extern u32 *ipu_dc_tmpl_reg;
+
+#define DC_EVT_NF		0
+#define DC_EVT_NL		1
+#define DC_EVT_EOF		2
+#define DC_EVT_NFIELD		3
+#define DC_EVT_EOL		4
+#define DC_EVT_EOFIELD		5
+#define DC_EVT_NEW_ADDR		6
+#define DC_EVT_NEW_CHAN		7
+#define DC_EVT_NEW_DATA		8
+
+#define DC_EVT_NEW_ADDR_W_0	0
+#define DC_EVT_NEW_ADDR_W_1	1
+#define DC_EVT_NEW_CHAN_W_0	2
+#define DC_EVT_NEW_CHAN_W_1	3
+#define DC_EVT_NEW_DATA_W_0	4
+#define DC_EVT_NEW_DATA_W_1	5
+#define DC_EVT_NEW_ADDR_R_0	6
+#define DC_EVT_NEW_ADDR_R_1	7
+#define DC_EVT_NEW_CHAN_R_0	8
+#define DC_EVT_NEW_CHAN_R_1	9
+#define DC_EVT_NEW_DATA_R_0	10
+#define DC_EVT_NEW_DATA_R_1	11
+
+/* Software reset for ipu */
+#define SW_IPU_RST	8
+
+enum {
+	IPU_CONF_DP_EN = 0x00000020,
+	IPU_CONF_DI0_EN = 0x00000040,
+	IPU_CONF_DI1_EN = 0x00000080,
+	IPU_CONF_DMFC_EN = 0x00000400,
+	IPU_CONF_DC_EN = 0x00000200,
+
+	DI0_COUNTER_RELEASE = 0x01000000,
+	DI1_COUNTER_RELEASE = 0x02000000,
+
+	DI_DW_GEN_ACCESS_SIZE_OFFSET = 24,
+	DI_DW_GEN_COMPONENT_SIZE_OFFSET = 16,
+
+	DI_GEN_DI_CLK_EXT = 0x100000,
+	DI_GEN_POLARITY_1 = 0x00000001,
+	DI_GEN_POLARITY_2 = 0x00000002,
+	DI_GEN_POLARITY_3 = 0x00000004,
+	DI_GEN_POLARITY_4 = 0x00000008,
+	DI_GEN_POLARITY_5 = 0x00000010,
+	DI_GEN_POLARITY_6 = 0x00000020,
+	DI_GEN_POLARITY_7 = 0x00000040,
+	DI_GEN_POLARITY_8 = 0x00000080,
+	DI_GEN_POL_CLK = 0x20000,
+
+	DI_POL_DRDY_DATA_POLARITY = 0x00000080,
+	DI_POL_DRDY_POLARITY_15 = 0x00000010,
+	DI_VSYNC_SEL_OFFSET = 13,
+
+	DC_WR_CH_CONF_FIELD_MODE = 0x00000200,
+	DC_WR_CH_CONF_PROG_TYPE_OFFSET = 5,
+	DC_WR_CH_CONF_PROG_TYPE_MASK = 0x000000E0,
+	DC_WR_CH_CONF_PROG_DI_ID = 0x00000004,
+	DC_WR_CH_CONF_PROG_DISP_ID_OFFSET = 3,
+	DC_WR_CH_CONF_PROG_DISP_ID_MASK = 0x00000018,
+
+	DP_COM_CONF_FG_EN = 0x00000001,
+	DP_COM_CONF_GWSEL = 0x00000002,
+	DP_COM_CONF_GWAM = 0x00000004,
+	DP_COM_CONF_GWCKE = 0x00000008,
+	DP_COM_CONF_CSC_DEF_MASK = 0x00000300,
+	DP_COM_CONF_CSC_DEF_OFFSET = 8,
+	DP_COM_CONF_CSC_DEF_FG = 0x00000300,
+	DP_COM_CONF_CSC_DEF_BG = 0x00000200,
+	DP_COM_CONF_CSC_DEF_BOTH = 0x00000100,
+	DP_COM_CONF_GAMMA_EN = 0x00001000,
+	DP_COM_CONF_GAMMA_YUV_EN = 0x00002000,
+};
+
+enum di_pins {
+	DI_PIN11 = 0,
+	DI_PIN12 = 1,
+	DI_PIN13 = 2,
+	DI_PIN14 = 3,
+	DI_PIN15 = 4,
+	DI_PIN16 = 5,
+	DI_PIN17 = 6,
+	DI_PIN_CS = 7,
+
+	DI_PIN_SER_CLK = 0,
+	DI_PIN_SER_RS = 1,
+};
+
+enum di_sync_wave {
+	DI_SYNC_NONE = -1,
+	DI_SYNC_CLK = 0,
+	DI_SYNC_INT_HSYNC = 1,
+	DI_SYNC_HSYNC = 2,
+	DI_SYNC_VSYNC = 3,
+	DI_SYNC_DE = 5,
+};
+
+struct ipu_cm {
+	u32 conf;
+	u32 sisg_ctrl0;
+	u32 sisg_ctrl1;
+	u32 sisg_set[6];
+	u32 sisg_clear[6];
+	u32 int_ctrl[15];
+	u32 sdma_event[10];
+	u32 srm_pri1;
+	u32 srm_pri2;
+	u32 fs_proc_flow[3];
+	u32 fs_disp_flow[2];
+	u32 skip;
+	u32 disp_alt_conf;
+	u32 disp_gen;
+	u32 disp_alt[4];
+	u32 snoop;
+	u32 mem_rst;
+	u32 pm;
+	u32 gpr;
+	u32 reserved0[26];
+	u32 ch_db_mode_sel[2];
+	u32 reserved1[16];
+	u32 alt_ch_db_mode_sel[2];
+	u32 reserved2[2];
+	u32 ch_trb_mode_sel[2];
+};
+
+struct ipu_idmac {
+	u32 conf;
+	u32 ch_en[2];
+	u32 sep_alpha;
+	u32 alt_sep_alpha;
+	u32 ch_pri[2];
+	u32 wm_en[2];
+	u32 lock_en[2];
+	u32 sub_addr[5];
+	u32 bndm_en[2];
+	u32 sc_cord[2];
+	u32 reserved[45];
+	u32 ch_busy[2];
+};
+
+struct ipu_com_async {
+	u32 com_conf_async;
+	u32 graph_wind_ctrl_async;
+	u32 fg_pos_async;
+	u32 cur_pos_async;
+	u32 cur_map_async;
+	u32 gamma_c_async[8];
+	u32 gamma_s_async[4];
+	u32 dp_csca_async[4];
+	u32 dp_csc_async[2];
+};
+
+struct ipu_dp {
+	u32 com_conf_sync;
+	u32 graph_wind_ctrl_sync;
+	u32 fg_pos_sync;
+	u32 cur_pos_sync;
+	u32 cur_map_sync;
+	u32 gamma_c_sync[8];
+	u32 gamma_s_sync[4];
+	u32 csca_sync[4];
+	u32 csc_sync[2];
+	u32 cur_pos_alt;
+	struct ipu_com_async async[2];
+};
+
+struct ipu_di {
+	u32 general;
+	u32 bs_clkgen0;
+	u32 bs_clkgen1;
+	u32 sw_gen0[9];
+	u32 sw_gen1[9];
+	u32 sync_as;
+	u32 dw_gen[12];
+	u32 dw_set[48];
+	u32 stp_rep[4];
+	u32 stp_rep9;
+	u32 ser_conf;
+	u32 ssc;
+	u32 pol;
+	u32 aw0;
+	u32 aw1;
+	u32 scr_conf;
+	u32 stat;
+};
+
+struct ipu_stat {
+	u32 int_stat[15];
+	u32 cur_buf[2];
+	u32 alt_cur_buf_0;
+	u32 alt_cur_buf_1;
+	u32 srm_stat;
+	u32 proc_task_stat;
+	u32 disp_task_stat;
+	u32 triple_cur_buf[4];
+	u32 ch_buf0_rdy[2];
+	u32 ch_buf1_rdy[2];
+	u32 alt_ch_buf0_rdy[2];
+	u32 alt_ch_buf1_rdy[2];
+	u32 ch_buf2_rdy[2];
+};
+
+struct ipu_dc_ch {
+	u32 wr_ch_conf;
+	u32 wr_ch_addr;
+	u32 rl[5];
+};
+
+struct ipu_dc {
+	struct ipu_dc_ch dc_ch0_1_2[3];
+	u32 cmd_ch_conf_3;
+	u32 cmd_ch_conf_4;
+	struct ipu_dc_ch dc_ch5_6[2];
+	struct ipu_dc_ch dc_ch8;
+	u32 rl6_ch_8;
+	struct ipu_dc_ch dc_ch9;
+	u32 rl6_ch_9;
+	u32 gen;
+	u32 disp_conf1[4];
+	u32 disp_conf2[4];
+	u32 di0_conf[2];
+	u32 di1_conf[2];
+	u32 dc_map_ptr[15];
+	u32 dc_map_val[12];
+	u32 udge[16];
+	u32 lla[2];
+	u32 r_lla[2];
+	u32 wr_ch_addr_5_alt;
+	u32 stat;
+};
+
+struct ipu_dmfc {
+	u32 rd_chan;
+	u32 wr_chan;
+	u32 wr_chan_def;
+	u32 dp_chan;
+	u32 dp_chan_def;
+	u32 general[2];
+	u32 ic_ctrl;
+	u32 wr_chan_alt;
+	u32 wr_chan_def_alt;
+	u32 general1_alt;
+	u32 stat;
+};
+
+#define IPU_CM_REG		((struct ipu_cm *)(IPU_CTRL_BASE_ADDR + \
+				IPU_CM_REG_BASE))
+#define IPU_CONF		(&IPU_CM_REG->conf)
+#define IPU_SRM_PRI1		(&IPU_CM_REG->srm_pri1)
+#define IPU_SRM_PRI2		(&IPU_CM_REG->srm_pri2)
+#define IPU_FS_PROC_FLOW1	(&IPU_CM_REG->fs_proc_flow[0])
+#define IPU_FS_PROC_FLOW2	(&IPU_CM_REG->fs_proc_flow[1])
+#define IPU_FS_PROC_FLOW3	(&IPU_CM_REG->fs_proc_flow[2])
+#define IPU_FS_DISP_FLOW1	(&IPU_CM_REG->fs_disp_flow[0])
+#define IPU_DISP_GEN		(&IPU_CM_REG->disp_gen)
+#define IPU_MEM_RST		(&IPU_CM_REG->mem_rst)
+#define IPU_GPR			(&IPU_CM_REG->gpr)
+#define IPU_CHA_DB_MODE_SEL(ch)	(&IPU_CM_REG->ch_db_mode_sel[ch / 32])
+
+#define IPU_STAT		((struct ipu_stat *)(IPU_CTRL_BASE_ADDR + \
+				IPU_STAT_REG_BASE))
+#define IPU_CHA_CUR_BUF(ch)	(&IPU_STAT->cur_buf[ch / 32])
+#define IPU_CHA_BUF0_RDY(ch)	(&IPU_STAT->ch_buf0_rdy[ch / 32])
+#define IPU_CHA_BUF1_RDY(ch)	(&IPU_STAT->ch_buf1_rdy[ch / 32])
+
+#define IPU_INT_CTRL(n)		(&IPU_CM_REG->int_ctrl[(n) - 1])
+
+#define IDMAC_REG		((struct ipu_idmac *)(IPU_CTRL_BASE_ADDR + \
+				IPU_IDMAC_REG_BASE))
+#define IDMAC_CONF		(&IDMAC_REG->conf)
+#define IDMAC_CHA_EN(ch)	(&IDMAC_REG->ch_en[ch / 32])
+#define IDMAC_CHA_PRI(ch)	(&IDMAC_REG->ch_pri[ch / 32])
+
+#define DI_REG(di)		((struct ipu_di *)(IPU_CTRL_BASE_ADDR + \
+				((di == 1) ? IPU_DI1_REG_BASE : \
+				IPU_DI0_REG_BASE)))
+#define DI_GENERAL(di)		(&DI_REG(di)->general)
+#define DI_BS_CLKGEN0(di)	(&DI_REG(di)->bs_clkgen0)
+#define DI_BS_CLKGEN1(di)	(&DI_REG(di)->bs_clkgen1)
+
+#define DI_SW_GEN0(di, gen)	(&DI_REG(di)->sw_gen0[gen - 1])
+#define DI_SW_GEN1(di, gen)	(&DI_REG(di)->sw_gen1[gen - 1])
+#define DI_STP_REP(di, gen)	(&DI_REG(di)->stp_rep[(gen - 1) / 2])
+#define DI_SYNC_AS_GEN(di)	(&DI_REG(di)->sync_as)
+#define DI_DW_GEN(di, gen)	(&DI_REG(di)->dw_gen[gen])
+#define DI_DW_SET(di, gen, set)	(&DI_REG(di)->dw_set[gen + 12 * set])
+#define DI_POL(di)		(&DI_REG(di)->pol)
+#define DI_SCR_CONF(di)		(&DI_REG(di)->scr_conf)
+
+#define DMFC_REG		((struct ipu_dmfc *)(IPU_CTRL_BASE_ADDR + \
+				IPU_DMFC_REG_BASE))
+#define DMFC_WR_CHAN		(&DMFC_REG->wr_chan)
+#define DMFC_WR_CHAN_DEF	(&DMFC_REG->wr_chan_def)
+#define DMFC_DP_CHAN		(&DMFC_REG->dp_chan)
+#define DMFC_DP_CHAN_DEF	(&DMFC_REG->dp_chan_def)
+#define DMFC_GENERAL1		(&DMFC_REG->general[0])
+#define DMFC_IC_CTRL		(&DMFC_REG->ic_ctrl)
+
+
+#define DC_REG			((struct ipu_dc *)(IPU_CTRL_BASE_ADDR + \
+				IPU_DC_REG_BASE))
+#define DC_MAP_CONF_PTR(n)	(&DC_REG->dc_map_ptr[n / 2])
+#define DC_MAP_CONF_VAL(n)	(&DC_REG->dc_map_val[n / 2])
+
+
+static inline struct ipu_dc_ch *dc_ch_offset(int ch)
+{
+	switch (ch) {
+	case 0:
+	case 1:
+	case 2:
+		return &DC_REG->dc_ch0_1_2[ch];
+	case 5:
+	case 6:
+		return &DC_REG->dc_ch5_6[ch - 5];
+	case 8:
+		return &DC_REG->dc_ch8;
+	case 9:
+		return &DC_REG->dc_ch9;
+	default:
+		printf("%s: invalid channel %d\n", __func__, ch);
+		return NULL;
+	}
+
+}
+
+#define DC_RL_CH(ch, evt)	(&dc_ch_offset(ch)->rl[evt / 2])
+
+#define DC_WR_CH_CONF(ch)	(&dc_ch_offset(ch)->wr_ch_conf)
+#define DC_WR_CH_ADDR(ch)	(&dc_ch_offset(ch)->wr_ch_addr)
+
+#define DC_WR_CH_CONF_1		DC_WR_CH_CONF(1)
+#define DC_WR_CH_CONF_5		DC_WR_CH_CONF(5)
+
+#define DC_GEN			(&DC_REG->gen)
+#define DC_DISP_CONF2(disp)	(&DC_REG->disp_conf2[disp])
+#define DC_STAT			(&DC_REG->stat)
+
+#define DP_SYNC 0
+#define DP_ASYNC0 0x60
+#define DP_ASYNC1 0xBC
+
+#define DP_REG			((struct ipu_dp *)(IPU_CTRL_BASE_ADDR + \
+				IPU_DP_REG_BASE))
+#define DP_COM_CONF(flow)	(&DP_REG->com_conf_sync)
+#define DP_GRAPH_WIND_CTRL(flow) (&DP_REG->graph_wind_ctrl_sync)
+#define DP_CSC_A_0(flow)	(&DP_REG->csca_sync[0])
+#define DP_CSC_A_1(flow)	(&DP_REG->csca_sync[1])
+#define DP_CSC_A_2(flow)	(&DP_REG->csca_sync[2])
+#define DP_CSC_A_3(flow)	(&DP_REG->csca_sync[3])
+
+#define DP_CSC_0(flow)		(&DP_REG->csc_sync[0])
+#define DP_CSC_1(flow)		(&DP_REG->csc_sync[1])
+
+/* DC template opcodes */
+#define WROD(lf)		(0x18 | (lf << 1))
+
+#endif
diff --git a/drivers/video/mxc_ipuv3_fb.c b/drivers/video/mxc_ipuv3_fb.c
new file mode 100644
index 0000000..a66981c
--- /dev/null
+++ b/drivers/video/mxc_ipuv3_fb.c
@@ -0,0 +1,642 @@
+/*
+ * Porting to u-boot:
+ *
+ * (C) Copyright 2010
+ * Stefano Babic, DENX Software Engineering, sbabic@denx.de
+ *
+ * MX51 Linux framebuffer:
+ *
+ * (C) Copyright 2004-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* #define DEBUG */
+#include <common.h>
+#include <asm/errno.h>
+#include <linux/string.h>
+#include <linux/list.h>
+#include <linux/fb.h>
+#include <asm/io.h>
+#include <malloc.h>
+#include <lcd.h>
+#include "videomodes.h"
+#include "ipu.h"
+#include "mxcfb.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void *lcd_base;			/* Start of framebuffer memory	*/
+void *lcd_console_address;	/* Start of console buffer	*/
+
+int lcd_line_length;
+int lcd_color_fg;
+int lcd_color_bg;
+
+short console_col;
+short console_row;
+
+vidinfo_t panel_info;
+
+static int mxcfb_map_video_memory(struct fb_info *fbi);
+static int mxcfb_unmap_video_memory(struct fb_info *fbi);
+
+void lcd_initcolregs(void)
+{
+}
+
+void lcd_setcolreg(ushort regno, ushort red, ushort green, ushort blue)
+{
+}
+
+void lcd_disable(void)
+{
+}
+
+void lcd_panel_disable(void)
+{
+}
+
+void fb_videomode_to_var(struct fb_var_screeninfo *var,
+			 const struct fb_videomode *mode)
+{
+	var->xres = mode->xres;
+	var->yres = mode->yres;
+	var->xres_virtual = mode->xres;
+	var->yres_virtual = mode->yres;
+	var->xoffset = 0;
+	var->yoffset = 0;
+	var->pixclock = mode->pixclock;
+	var->left_margin = mode->left_margin;
+	var->right_margin = mode->right_margin;
+	var->upper_margin = mode->upper_margin;
+	var->lower_margin = mode->lower_margin;
+	var->hsync_len = mode->hsync_len;
+	var->vsync_len = mode->vsync_len;
+	var->sync = mode->sync;
+	var->vmode = mode->vmode & FB_VMODE_MASK;
+}
+
+/*
+ * Structure containing the MXC specific framebuffer information.
+ */
+struct mxcfb_info {
+	int blank;
+	ipu_channel_t ipu_ch;
+	int ipu_di;
+	u32 ipu_di_pix_fmt;
+	unsigned char overlay;
+	unsigned char alpha_chan_en;
+	dma_addr_t alpha_phy_addr0;
+	dma_addr_t alpha_phy_addr1;
+	void *alpha_virt_addr0;
+	void *alpha_virt_addr1;
+	uint32_t alpha_mem_len;
+	uint32_t cur_ipu_buf;
+	uint32_t cur_ipu_alpha_buf;
+
+	u32 pseudo_palette[16];
+};
+
+enum {
+	BOTH_ON,
+	SRC_ON,
+	TGT_ON,
+	BOTH_OFF
+};
+
+static unsigned long default_bpp = 16;
+static unsigned char g_dp_in_use;
+static struct fb_info *mxcfb_info[3];
+static int ext_clk_used;
+
+static uint32_t bpp_to_pixfmt(struct fb_info *fbi)
+{
+	uint32_t pixfmt = 0;
+
+	debug("bpp_to_pixfmt: %d\n", fbi->var.bits_per_pixel);
+
+	if (fbi->var.nonstd)
+		return fbi->var.nonstd;
+
+	switch (fbi->var.bits_per_pixel) {
+	case 24:
+		pixfmt = IPU_PIX_FMT_BGR24;
+		break;
+	case 32:
+		pixfmt = IPU_PIX_FMT_BGR32;
+		break;
+	case 16:
+		pixfmt = IPU_PIX_FMT_RGB565;
+		break;
+	}
+	return pixfmt;
+}
+
+/*
+ * Set fixed framebuffer parameters based on variable settings.
+ *
+ * @param       info     framebuffer information pointer
+ */
+static int mxcfb_set_fix(struct fb_info *info)
+{
+	struct fb_fix_screeninfo *fix = &info->fix;
+	struct fb_var_screeninfo *var = &info->var;
+
+	fix->line_length = var->xres_virtual * var->bits_per_pixel / 8;
+
+	fix->type = FB_TYPE_PACKED_PIXELS;
+	fix->accel = FB_ACCEL_NONE;
+	fix->visual = FB_VISUAL_TRUECOLOR;
+	fix->xpanstep = 1;
+	fix->ypanstep = 1;
+
+	return 0;
+}
+
+static int setup_disp_channel1(struct fb_info *fbi)
+{
+	ipu_channel_params_t params;
+	struct mxcfb_info *mxc_fbi = (struct mxcfb_info *)fbi->par;
+
+	memset(&params, 0, sizeof(params));
+	params.mem_dp_bg_sync.di = mxc_fbi->ipu_di;
+
+	debug("%s called\n", __func__);
+	/*
+	 * Assuming interlaced means yuv output, below setting also
+	 * valid for mem_dc_sync. FG should have the same vmode as BG.
+	 */
+	if (fbi->var.vmode & FB_VMODE_INTERLACED) {
+		params.mem_dp_bg_sync.interlaced = 1;
+		params.mem_dp_bg_sync.out_pixel_fmt =
+			IPU_PIX_FMT_YUV444;
+	} else {
+		if (mxc_fbi->ipu_di_pix_fmt) {
+			params.mem_dp_bg_sync.out_pixel_fmt =
+				mxc_fbi->ipu_di_pix_fmt;
+		} else {
+			params.mem_dp_bg_sync.out_pixel_fmt =
+				IPU_PIX_FMT_RGB666;
+		}
+	}
+	params.mem_dp_bg_sync.in_pixel_fmt = bpp_to_pixfmt(fbi);
+	if (mxc_fbi->alpha_chan_en)
+		params.mem_dp_bg_sync.alpha_chan_en = 1;
+
+	ipu_init_channel(mxc_fbi->ipu_ch, &params);
+
+	return 0;
+}
+
+static int setup_disp_channel2(struct fb_info *fbi)
+{
+	int retval = 0;
+	struct mxcfb_info *mxc_fbi = (struct mxcfb_info *)fbi->par;
+
+	mxc_fbi->cur_ipu_buf = 1;
+	if (mxc_fbi->alpha_chan_en)
+		mxc_fbi->cur_ipu_alpha_buf = 1;
+
+	fbi->var.xoffset = fbi->var.yoffset = 0;
+
+	debug("%s: %x %d %d %d %lx %lx\n",
+		__func__,
+		mxc_fbi->ipu_ch,
+		fbi->var.xres,
+		fbi->var.yres,
+		fbi->fix.line_length,
+		fbi->fix.smem_start,
+		fbi->fix.smem_start +
+		(fbi->fix.line_length * fbi->var.yres));
+
+	retval = ipu_init_channel_buffer(mxc_fbi->ipu_ch, IPU_INPUT_BUFFER,
+					 bpp_to_pixfmt(fbi),
+					 fbi->var.xres, fbi->var.yres,
+					 fbi->fix.line_length,
+					 fbi->fix.smem_start +
+					 (fbi->fix.line_length * fbi->var.yres),
+					 fbi->fix.smem_start,
+					 0, 0);
+	if (retval)
+		printf("ipu_init_channel_buffer error %d\n", retval);
+
+	return retval;
+}
+
+/*
+ * Set framebuffer parameters and change the operating mode.
+ *
+ * @param       info     framebuffer information pointer
+ */
+static int mxcfb_set_par(struct fb_info *fbi)
+{
+	int retval = 0;
+	u32 mem_len;
+	ipu_di_signal_cfg_t sig_cfg;
+	struct mxcfb_info *mxc_fbi = (struct mxcfb_info *)fbi->par;
+	uint32_t out_pixel_fmt;
+
+	ipu_disable_channel(mxc_fbi->ipu_ch);
+	ipu_uninit_channel(mxc_fbi->ipu_ch);
+	mxcfb_set_fix(fbi);
+
+	mem_len = fbi->var.yres_virtual * fbi->fix.line_length;
+	if (!fbi->fix.smem_start || (mem_len > fbi->fix.smem_len)) {
+		if (fbi->fix.smem_start)
+			mxcfb_unmap_video_memory(fbi);
+
+		if (mxcfb_map_video_memory(fbi) < 0)
+			return -ENOMEM;
+	}
+
+	setup_disp_channel1(fbi);
+
+	memset(&sig_cfg, 0, sizeof(sig_cfg));
+	if (fbi->var.vmode & FB_VMODE_INTERLACED) {
+		sig_cfg.interlaced = 1;
+		out_pixel_fmt = IPU_PIX_FMT_YUV444;
+	} else {
+		if (mxc_fbi->ipu_di_pix_fmt)
+			out_pixel_fmt = mxc_fbi->ipu_di_pix_fmt;
+		else
+			out_pixel_fmt = IPU_PIX_FMT_RGB666;
+	}
+	if (fbi->var.vmode & FB_VMODE_ODD_FLD_FIRST) /* PAL */
+		sig_cfg.odd_field_first = 1;
+	if ((fbi->var.sync & FB_SYNC_EXT) || ext_clk_used)
+		sig_cfg.ext_clk = 1;
+	if (fbi->var.sync & FB_SYNC_HOR_HIGH_ACT)
+		sig_cfg.Hsync_pol = 1;
+	if (fbi->var.sync & FB_SYNC_VERT_HIGH_ACT)
+		sig_cfg.Vsync_pol = 1;
+	if (!(fbi->var.sync & FB_SYNC_CLK_LAT_FALL))
+		sig_cfg.clk_pol = 1;
+	if (fbi->var.sync & FB_SYNC_DATA_INVERT)
+		sig_cfg.data_pol = 1;
+	if (!(fbi->var.sync & FB_SYNC_OE_LOW_ACT))
+		sig_cfg.enable_pol = 1;
+	if (fbi->var.sync & FB_SYNC_CLK_IDLE_EN)
+		sig_cfg.clkidle_en = 1;
+
+	debug("pixclock = %ul Hz\n",
+		(u32) (PICOS2KHZ(fbi->var.pixclock) * 1000UL));
+
+	if (ipu_init_sync_panel(mxc_fbi->ipu_di,
+				(PICOS2KHZ(fbi->var.pixclock)) * 1000UL,
+				fbi->var.xres, fbi->var.yres,
+				out_pixel_fmt,
+				fbi->var.left_margin,
+				fbi->var.hsync_len,
+				fbi->var.right_margin,
+				fbi->var.upper_margin,
+				fbi->var.vsync_len,
+				fbi->var.lower_margin,
+				0, sig_cfg) != 0) {
+		puts("mxcfb: Error initializing panel.\n");
+		return -EINVAL;
+	}
+
+	retval = setup_disp_channel2(fbi);
+	if (retval)
+		return retval;
+
+	if (mxc_fbi->blank == FB_BLANK_UNBLANK)
+		ipu_enable_channel(mxc_fbi->ipu_ch);
+
+	return retval;
+}
+
+/*
+ * Check framebuffer variable parameters and adjust to valid values.
+ *
+ * @param       var      framebuffer variable parameters
+ *
+ * @param       info     framebuffer information pointer
+ */
+static int mxcfb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
+{
+	u32 vtotal;
+	u32 htotal;
+
+	if (var->xres_virtual < var->xres)
+		var->xres_virtual = var->xres;
+	if (var->yres_virtual < var->yres)
+		var->yres_virtual = var->yres;
+
+	if ((var->bits_per_pixel != 32) && (var->bits_per_pixel != 24) &&
+	    (var->bits_per_pixel != 16) && (var->bits_per_pixel != 8))
+		var->bits_per_pixel = default_bpp;
+
+	switch (var->bits_per_pixel) {
+	case 8:
+		var->red.length = 3;
+		var->red.offset = 5;
+		var->red.msb_right = 0;
+
+		var->green.length = 3;
+		var->green.offset = 2;
+		var->green.msb_right = 0;
+
+		var->blue.length = 2;
+		var->blue.offset = 0;
+		var->blue.msb_right = 0;
+
+		var->transp.length = 0;
+		var->transp.offset = 0;
+		var->transp.msb_right = 0;
+		break;
+	case 16:
+		var->red.length = 5;
+		var->red.offset = 11;
+		var->red.msb_right = 0;
+
+		var->green.length = 6;
+		var->green.offset = 5;
+		var->green.msb_right = 0;
+
+		var->blue.length = 5;
+		var->blue.offset = 0;
+		var->blue.msb_right = 0;
+
+		var->transp.length = 0;
+		var->transp.offset = 0;
+		var->transp.msb_right = 0;
+		break;
+	case 24:
+		var->red.length = 8;
+		var->red.offset = 16;
+		var->red.msb_right = 0;
+
+		var->green.length = 8;
+		var->green.offset = 8;
+		var->green.msb_right = 0;
+
+		var->blue.length = 8;
+		var->blue.offset = 0;
+		var->blue.msb_right = 0;
+
+		var->transp.length = 0;
+		var->transp.offset = 0;
+		var->transp.msb_right = 0;
+		break;
+	case 32:
+		var->red.length = 8;
+		var->red.offset = 16;
+		var->red.msb_right = 0;
+
+		var->green.length = 8;
+		var->green.offset = 8;
+		var->green.msb_right = 0;
+
+		var->blue.length = 8;
+		var->blue.offset = 0;
+		var->blue.msb_right = 0;
+
+		var->transp.length = 8;
+		var->transp.offset = 24;
+		var->transp.msb_right = 0;
+		break;
+	}
+
+	if (var->pixclock < 1000) {
+		htotal = var->xres + var->right_margin + var->hsync_len +
+		    var->left_margin;
+		vtotal = var->yres + var->lower_margin + var->vsync_len +
+		    var->upper_margin;
+		var->pixclock = (vtotal * htotal * 6UL) / 100UL;
+		var->pixclock = KHZ2PICOS(var->pixclock);
+		printf("pixclock set for 60Hz refresh = %u ps\n",
+			var->pixclock);
+	}
+
+	var->height = -1;
+	var->width = -1;
+	var->grayscale = 0;
+
+	return 0;
+}
+
+static int mxcfb_map_video_memory(struct fb_info *fbi)
+{
+	if (fbi->fix.smem_len < fbi->var.yres_virtual * fbi->fix.line_length) {
+		fbi->fix.smem_len = fbi->var.yres_virtual *
+				    fbi->fix.line_length;
+	}
+
+	fbi->screen_base = (char *)lcd_base;
+	fbi->fix.smem_start = (unsigned long)lcd_base;
+	if (fbi->screen_base == 0) {
+		puts("Unable to allocate framebuffer memory\n");
+		fbi->fix.smem_len = 0;
+		fbi->fix.smem_start = 0;
+		return -EBUSY;
+	}
+
+	debug("allocated fb @ paddr=0x%08X, size=%d.\n",
+		(uint32_t) fbi->fix.smem_start, fbi->fix.smem_len);
+
+	fbi->screen_size = fbi->fix.smem_len;
+
+	/* Clear the screen */
+	memset((char *)fbi->screen_base, 0, fbi->fix.smem_len);
+
+	return 0;
+}
+
+static int mxcfb_unmap_video_memory(struct fb_info *fbi)
+{
+	fbi->screen_base = 0;
+	fbi->fix.smem_start = 0;
+	fbi->fix.smem_len = 0;
+	return 0;
+}
+
+/*
+ * Initializes the framebuffer information pointer. After allocating
+ * sufficient memory for the framebuffer structure, the fields are
+ * filled with custom information passed in from the configurable
+ * structures.  This includes information such as bits per pixel,
+ * color maps, screen width/height and RGBA offsets.
+ *
+ * @return      Framebuffer structure initialized with our information
+ */
+static struct fb_info *mxcfb_init_fbinfo(void)
+{
+#define BYTES_PER_LONG 4
+#define PADDING (BYTES_PER_LONG - (sizeof(struct fb_info) % BYTES_PER_LONG))
+	struct fb_info *fbi;
+	struct mxcfb_info *mxcfbi;
+	char *p;
+	int size = sizeof(struct mxcfb_info) + PADDING +
+		sizeof(struct fb_info);
+
+	debug("%s: %d %d %d %d\n",
+		__func__,
+		PADDING,
+		size,
+		sizeof(struct mxcfb_info),
+		sizeof(struct fb_info));
+	/*
+	 * Allocate sufficient memory for the fb structure
+	 */
+
+	p = malloc(size);
+	if (!p)
+		return NULL;
+
+	memset(p, 0, size);
+
+	fbi = (struct fb_info *)p;
+	fbi->par = p + sizeof(struct fb_info) + PADDING;
+
+	mxcfbi = (struct mxcfb_info *)fbi->par;
+	debug("Framebuffer structures at: fbi=0x%x mxcfbi=0x%x\n",
+		(unsigned int)fbi, (unsigned int)mxcfbi);
+
+	fbi->var.activate = FB_ACTIVATE_NOW;
+
+	fbi->flags = FBINFO_FLAG_DEFAULT;
+	fbi->pseudo_palette = mxcfbi->pseudo_palette;
+
+	return fbi;
+}
+
+/*
+ * Probe routine for the framebuffer driver. It is called during the
+ * driver binding process.      The following functions are performed in
+ * this routine: Framebuffer initialization, Memory allocation and
+ * mapping, Framebuffer registration, IPU initialization.
+ *
+ * @return      Appropriate error code to the kernel common code
+ */
+static int mxcfb_probe(u32 interface_pix_fmt, struct fb_videomode *mode)
+{
+	struct fb_info *fbi;
+	struct mxcfb_info *mxcfbi;
+	int ret = 0;
+
+	/*
+	 * Initialize FB structures
+	 */
+	fbi = mxcfb_init_fbinfo();
+	if (!fbi) {
+		ret = -ENOMEM;
+		goto err0;
+	}
+	mxcfbi = (struct mxcfb_info *)fbi->par;
+
+	if (!g_dp_in_use) {
+		mxcfbi->ipu_ch = MEM_BG_SYNC;
+		mxcfbi->blank = FB_BLANK_UNBLANK;
+	} else {
+		mxcfbi->ipu_ch = MEM_DC_SYNC;
+		mxcfbi->blank = FB_BLANK_POWERDOWN;
+	}
+
+	mxcfbi->ipu_di = 0;
+
+	ipu_disp_set_global_alpha(mxcfbi->ipu_ch, 1, 0x80);
+	ipu_disp_set_color_key(mxcfbi->ipu_ch, 0, 0);
+	strcpy(fbi->fix.id, "DISP3 BG");
+
+	g_dp_in_use = 1;
+
+	mxcfb_info[mxcfbi->ipu_di] = fbi;
+
+	/* Need dummy values until real panel is configured */
+	fbi->var.xres = 640;
+	fbi->var.yres = 480;
+	fbi->var.bits_per_pixel = 16;
+
+	mxcfbi->ipu_di_pix_fmt = interface_pix_fmt;
+	fb_videomode_to_var(&fbi->var, mode);
+
+	mxcfb_check_var(&fbi->var, fbi);
+
+	/* Default Y virtual size is 2x panel size */
+	fbi->var.yres_virtual = fbi->var.yres * 2;
+
+	mxcfb_set_fix(fbi);
+
+	/* alocate fb first */
+	if (mxcfb_map_video_memory(fbi) < 0)
+		return -ENOMEM;
+
+	mxcfb_set_par(fbi);
+
+	/* Setting panel_info for lcd */
+	panel_info.cmap = NULL;
+	panel_info.vl_col = fbi->var.xres;
+	panel_info.vl_row = fbi->var.yres;
+	panel_info.vl_bpix = LCD_BPP;
+
+	lcd_line_length = (panel_info.vl_col * NBITS(panel_info.vl_bpix)) / 8;
+
+	debug("MXC IPUV3 configured\n"
+		"XRES = %d YRES = %d BitsXpixel = %d\n",
+		panel_info.vl_col,
+		panel_info.vl_row,
+		panel_info.vl_bpix);
+
+	ipu_dump_registers();
+
+	return 0;
+
+err0:
+	return ret;
+}
+
+int overwrite_console(void)
+{
+	/* Keep stdout / stderr on serial, our LCD is for splashscreen only */
+	return 1;
+}
+
+void lcd_ctrl_init(void *lcdbase)
+{
+	u32 mem_len = panel_info.vl_col *
+		panel_info.vl_row *
+		NBITS(panel_info.vl_bpix) / 8;
+
+	/*
+	 * We rely on lcdbase being a physical address, i.e., either MMU off,
+	 * or 1-to-1 mapping. Might want to add some virt2phys here.
+	 */
+	if (!lcdbase)
+		return;
+
+	memset(lcdbase, 0, mem_len);
+}
+
+int mx51_fb_init(struct fb_videomode *mode)
+{
+	int ret;
+
+	ret = ipu_probe();
+	if (ret)
+		puts("Error initializing IPU\n");
+
+	lcd_base += 56;
+
+	debug("Framebuffer at 0x%x\n", (unsigned int)lcd_base);
+	ret = mxcfb_probe(IPU_PIX_FMT_RGB666, mode);
+
+	return ret;
+}
diff --git a/drivers/video/mxcfb.h b/drivers/video/mxcfb.h
new file mode 100644
index 0000000..d508196
--- /dev/null
+++ b/drivers/video/mxcfb.h
@@ -0,0 +1,68 @@
+/*
+ * Porting to u-boot:
+ *
+ * (C) Copyright 2010
+ * Stefano Babic, DENX Software Engineering, sbabic@denx.de
+ *
+ * Linux IPU driver for MX51:
+ *
+ * (C) Copyright 2004-2009 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ASM_ARCH_MXCFB_H__
+#define __ASM_ARCH_MXCFB_H__
+
+#define FB_SYNC_OE_LOW_ACT	0x80000000
+#define FB_SYNC_CLK_LAT_FALL	0x40000000
+#define FB_SYNC_DATA_INVERT	0x20000000
+#define FB_SYNC_CLK_IDLE_EN	0x10000000
+#define FB_SYNC_SHARP_MODE	0x08000000
+#define FB_SYNC_SWAP_RGB	0x04000000
+
+struct mxcfb_gbl_alpha {
+	int enable;
+	int alpha;
+};
+
+struct mxcfb_loc_alpha {
+	int enable;
+	int alpha_in_pixel;
+	unsigned long alpha_phy_addr0;
+	unsigned long alpha_phy_addr1;
+};
+
+struct mxcfb_color_key {
+	int enable;
+	__u32 color_key;
+};
+
+struct mxcfb_pos {
+	__u16 x;
+	__u16 y;
+};
+
+struct mxcfb_gamma {
+	int enable;
+	int constk[16];
+	int slopek[16];
+};
+
+#endif
diff --git a/include/configs/KUP4K.h b/include/configs/KUP4K.h
index 9702d63..c8e0ff2 100644
--- a/include/configs/KUP4K.h
+++ b/include/configs/KUP4K.h
@@ -139,9 +139,9 @@
 
 /* List of I2C addresses to be verified by POST */
 
-#define I2C_ADDR_LIST	{CONFIG_SYS_I2C_PICIO_ADDR,	\
-			CONFIG_SYS_I2C_RTC_ADDR,	\
-			}
+#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_PICIO_ADDR,	\
+					 CONFIG_SYS_I2C_RTC_ADDR,	\
+					}
 
 #define CONFIG_RTC_PCF8563		/* use Philips PCF8563 RTC	*/
 
diff --git a/include/configs/KUP4X.h b/include/configs/KUP4X.h
index 9613ed9..ce731e3 100644
--- a/include/configs/KUP4X.h
+++ b/include/configs/KUP4X.h
@@ -149,9 +149,9 @@
 
 /* List of I2C addresses to be verified by POST */
 
-#define I2C_ADDR_LIST	{CONFIG_SYS_I2C_PICIO_ADDR,	\
-			CONFIG_SYS_I2C_RTC_ADDR,	\
-			}
+#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_PICIO_ADDR,	\
+					 CONFIG_SYS_I2C_RTC_ADDR,	\
+					}
 
 
 #define CONFIG_RTC_PCF8563		/* use Philips PCF8563 RTC	*/
diff --git a/include/configs/MVBLM7.h b/include/configs/MVBLM7.h
index 04d97cd..44d45e3 100644
--- a/include/configs/MVBLM7.h
+++ b/include/configs/MVBLM7.h
@@ -324,7 +324,7 @@
 #define CONFIG_SYS_SCCR_TSEC1CM	1
 #define CONFIG_SYS_SCCR_TSEC2CM	1
 
-#define CONFIG_SYS_SICRH	0x1fff8003
+#define CONFIG_SYS_SICRH	0x1fef0003
 #define CONFIG_SYS_SICRL	(SICRL_LDP_A | SICRL_USB1 | SICRL_USB0)
 
 #define CONFIG_SYS_HID0_INIT	0x000000000
diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h
index ad86e2e..f336e8d 100644
--- a/include/configs/TB5200.h
+++ b/include/configs/TB5200.h
@@ -251,10 +251,10 @@
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
 
 /* List of I2C addresses to be verified by POST */
-#undef I2C_ADDR_LIST
-#define I2C_ADDR_LIST	{	CONFIG_SYS_I2C_EEPROM_ADDR,	\
-				CONFIG_SYS_I2C_RTC_ADDR,	\
-				CONFIG_SYS_I2C_SLAVE }
+#undef CONFIG_SYS_POST_I2C_ADDRS
+#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_EEPROM_ADDR,	\
+					 CONFIG_SYS_I2C_RTC_ADDR,	\
+					 CONFIG_SYS_I2C_SLAVE}
 
 /*
  * Flash configuration
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 2612c7a..794e11b 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -370,10 +370,10 @@
 
 /* List of I2C addresses to be verified by POST */
 #if defined (CONFIG_MINIFAP)
-#undef I2C_ADDR_LIST
-#define I2C_ADDR_LIST	{	CONFIG_SYS_I2C_EEPROM_ADDR,	\
-				CONFIG_SYS_I2C_HWMON_ADDR,	\
-				CONFIG_SYS_I2C_SLAVE }
+#undef CONFIG_SYS_POST_I2C_ADDRS
+#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_EEPROM_ADDR,	\
+					 CONFIG_SYS_I2C_HWMON_ADDR,	\
+					 CONFIG_SYS_I2C_SLAVE}
 #endif
 
 /*
diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h
index 24a04eb..f18bc45 100644
--- a/include/configs/a4m072.h
+++ b/include/configs/a4m072.h
@@ -147,27 +147,43 @@
 #define CONFIG_PREBOOT				"run try_update"
 
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"bk=run add_mtd ; run add_consolespec ; bootm 200000\0"	\
-	"cf1=diskboot 200000 0:1\0"	\
-	"bootcmd_cf1=run bcf1\0"	\
-	"bcf=setenv bootargs root=/dev/hda3\0"	\
-	"bootcmd_nfs=run bnfs\0"	\
-	"norargs=setenv bootargs root=/dev/mtdblock3 rootfstype=cramfs\0"	\
-	"bootcmd_nor=cp.b ${kernel_addr} 200000 100000; run norargs addip; run bk\0"	\
-	"bnfs=nfs 200000 ${rootpath}/boot/uImage ; run nfsargs addip ; run bk\0"	\
-	"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0"	\
-	"try_update=usb start;sleep 2;usb start;sleep 1;fatload usb 0 2F0000 PCPUUPDT 2FF;usb stop;source 2F0000\0"	\
-	"env_addr=FE060000\0"	\
-	"kernel_addr=FE100000\0"	\
-	"rootfs_addr=FE200000\0"	\
-	"add_mtd=setenv bootargs ${bootargs} mtdparts=phys_mapped_flash:384k(u),640k(e),1m(k),30m(r)\0"	\
-	"bcf1=run cf1; run bcf; run addip; run bk\0"	\
-	"add_consolespec=setenv bootargs ${bootargs} console=/dev/null quiet\0"	\
-	"addip=if test \"${ethaddr}\" != \"00:00:00:00:00:00\" ; then if test -n ${ipaddr}; then setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off panic=1; fi ; fi\0"	\
-	"hostname=CPUP0\0"	\
-	"ethaddr=00:00:00:00:00:00\0"	\
-	"netdev=eth0\0"	\
-	"bootcmd=run bootcmd_nor\0" \
+	"bk=run add_mtd ; run add_consolespec ; bootm 200000\0"		\
+	"cf1=diskboot 200000 0:1\0"					\
+	"bootcmd_cf1=run bcf1\0"					\
+	"bcf=setenv bootargs root=/dev/hda3\0"				\
+	"bootcmd_nfs=run bnfs\0"					\
+	"norargs=setenv bootargs root=/dev/mtdblock3 rootfstype=cramfs "\
+		"panic=1\0"						\
+	"bootcmd_nor=cp.b ${kernel_addr} 200000 100000;"		\
+			"run norargs addip; run bk\0"			\
+	"bnfs=nfs 200000 ${rootpath}/boot/uImage;"			\
+			"run nfsargs addip ; run bk\0"			\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+				"nfsroot=${serverip}:${rootpath}\0"	\
+	"try_update=usb start;sleep 2;usb start;sleep 1;"		\
+			"fatload usb 0 2F0000 PCPUUPDT 2FF;usb stop;"	\
+			"source 2F0000\0"				\
+	"env_addr=FE060000\0"						\
+	"kernel_addr=FE100000\0"					\
+	"rootfs_addr=FE200000\0"					\
+	"add_mtd=setenv bootargs ${bootargs} mtdparts="			\
+		"phys_mapped_flash:384k(u),640k(e),1m(k),30m(r)\0"	\
+	"bcf1=run cf1; run bcf; run addip; run bk\0"			\
+	"add_consolespec=setenv bootargs ${bootargs} "			\
+				"console=/dev/null quiet\0"		\
+	"addip=if test -n ${ethaddr};"					\
+		"then if test -n ${ipaddr};"				\
+			"then setenv bootargs ${bootargs} "		\
+				"ip=${ipaddr}:${serverip}:${gatewayip}:"\
+				"${netmask}:${hostname}:${netdev}:off;"	\
+			"fi;"						\
+		"else;"							\
+			"setenv bootargs ${bootargs} no_ethaddr;"	\
+		"fi\0"							\
+	"hostname=CPUP0\0"						\
+	"ethaddr=00:00:00:00:00:00\0"					\
+	"netdev=eth0\0"							\
+	"bootcmd=run bootcmd_nor\0" 					\
 	""
 /*
  * IPB Bus clocking configuration.
@@ -212,6 +228,7 @@
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_CS0_START}
+#define CONFIG_SYS_FLASH_BANKS_SIZES	{CONFIG_SYS_CS0_SIZE}
 
 /*
  * Environment settings
diff --git a/include/configs/cerf250.h b/include/configs/cerf250.h
index 98b69e3..a0726a9 100644
--- a/include/configs/cerf250.h
+++ b/include/configs/cerf250.h
@@ -38,6 +38,7 @@
 #define CONFIG_CERF250		1	/* on Cerf PXA Board	    */
 #define BOARD_LATE_INIT		1
 #define CONFIG_BAUDRATE		38400
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 #undef	CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */
 
@@ -140,15 +141,9 @@
 /*
  * Physical Memory Map
  */
-#define CONFIG_NR_DRAM_BANKS	4			/* we have 2 banks of DRAM */
+#define CONFIG_NR_DRAM_BANKS		1		/* we have 1 bank of DRAM */
 #define PHYS_SDRAM_1			0xa0000000	/* SDRAM Bank #1 */
 #define PHYS_SDRAM_1_SIZE		0x04000000	/* 64 MB */
-#define PHYS_SDRAM_2			0xa4000000	/* SDRAM Bank #2 */
-#define PHYS_SDRAM_2_SIZE		0x00000000	/* 0 MB */
-#define PHYS_SDRAM_3			0xa8000000	/* SDRAM Bank #3 */
-#define PHYS_SDRAM_3_SIZE		0x00000000	/* 0 MB */
-#define PHYS_SDRAM_4			0xac000000	/* SDRAM Bank #4 */
-#define PHYS_SDRAM_4_SIZE		0x00000000	/* 0 MB */
 
 #define PHYS_FLASH_1			0x00000000	/* Flash Bank #1 */
 #define PHYS_FLASH_2			0x04000000	/* Flash Bank #2 */
@@ -187,6 +182,9 @@
 
 #define CONFIG_SYS_PSSR_VAL		0x20
 
+#define	CONFIG_SYS_CCCR			CCCR_L27|CCCR_M2|CCCR_N10
+#define	CONFIG_SYS_CKEN			0x0
+
 /*
  * Memory settings
  */
@@ -196,6 +194,8 @@
 #define CONFIG_SYS_MDCNFG_VAL		0x00001AC9
 #define CONFIG_SYS_MDREFR_VAL		0x03CDC017
 #define CONFIG_SYS_MDMRS_VAL		0x00000000
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
 
 /*
  * PCMCIA and CF Interfaces
diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h
index 1b129a2..af6769b 100644
--- a/include/configs/cm5200.h
+++ b/include/configs/cm5200.h
@@ -80,7 +80,9 @@
 #define CONFIG_POST		(CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
 #define MPC5XXX_SRAM_POST_SIZE	(MPC5XXX_SRAM_SIZE - 4)
 /* List of I2C addresses to be verified by POST */
-#define I2C_ADDR_LIST		{ CONFIG_SYS_I2C_SLAVE, CONFIG_SYS_I2C_IO, CONFIG_SYS_I2C_EEPROM }
+#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_SLAVE,	\
+					 CONFIG_SYS_I2C_IO,	\
+					 CONFIG_SYS_I2C_EEPROM}
 
 /* display image timestamps */
 #define CONFIG_TIMESTAMP	1
diff --git a/include/configs/colibri_pxa270.h b/include/configs/colibri_pxa270.h
index 5f457f8..afc1537 100644
--- a/include/configs/colibri_pxa270.h
+++ b/include/configs/colibri_pxa270.h
@@ -39,7 +39,7 @@
 #define	CONFIG_ENV_SIZE			0x4000
 #define	CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
 #define	CONFIG_SYS_GBL_DATA_SIZE	128
-
+#define	CONFIG_SYS_TEXT_BASE		0x0
 #define	CONFIG_ENV_OVERWRITE		/* override default environment */
 
 #define	CONFIG_BOOTCOMMAND						\
diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h
index 85147d0..2733fb2 100644
--- a/include/configs/corenet_ds.h
+++ b/include/configs/corenet_ds.h
@@ -213,7 +213,7 @@
 #endif
 #define CONFIG_SYS_INIT_RAM_END		0x00004000	/* End of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE	256	/* num bytes initial data */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
diff --git a/include/configs/cradle.h b/include/configs/cradle.h
index d1c1a48..3da3562 100644
--- a/include/configs/cradle.h
+++ b/include/configs/cradle.h
@@ -39,7 +39,7 @@
 
 /* we will never enable dcache, because we have to setup MMU first */
 #define CONFIG_SYS_NO_DCACHE
-
+#define	CONFIG_SYS_TEXT_BASE		0x0
 /*
  * Size of malloc() pool
  */
@@ -126,15 +126,9 @@
 /*
  * Physical Memory Map
  */
-#define CONFIG_NR_DRAM_BANKS    4          /* we have 2 banks of DRAM */
+#define CONFIG_NR_DRAM_BANKS    1          /* we have 1 bank of DRAM */
 #define PHYS_SDRAM_1            0xa0000000 /* SDRAM Bank #1 */
 #define PHYS_SDRAM_1_SIZE       0x01000000 /* 64 MB */
-#define PHYS_SDRAM_2            0xa4000000 /* SDRAM Bank #2 */
-#define PHYS_SDRAM_2_SIZE       0x00000000 /* 0 MB */
-#define PHYS_SDRAM_3            0xa8000000 /* SDRAM Bank #3 */
-#define PHYS_SDRAM_3_SIZE       0x00000000 /* 0 MB */
-#define PHYS_SDRAM_4            0xac000000 /* SDRAM Bank #4 */
-#define PHYS_SDRAM_4_SIZE       0x00000000 /* 0 MB */
 
 #define PHYS_FLASH_1            0x00000000 /* Flash Bank #1 */
 #define PHYS_FLASH_2            0x04000000 /* Flash Bank #1 */
@@ -289,9 +283,9 @@
  * Clocks, power control and interrupts
  */
 #define CONFIG_SYS_PSSR_VAL        0x00000020
-#define CONFIG_SYS_CCCR_VAL        0x00000141  /* 100 MHz memory, 200 MHz CPU  */
-#define CONFIG_SYS_CKEN_VAL        0x00000060  /* FFUART and STUART enabled    */
-#define CONFIG_SYS_ICMR_VAL        0x00000000  /* No interrupts enabled        */
+#define CONFIG_SYS_CCCR        0x00000141  /* 100 MHz memory, 200 MHz CPU  */
+#define CONFIG_SYS_CKEN        0x00000060  /* FFUART and STUART enabled    */
+#define CONFIG_SYS_ICMR        0x00000000  /* No interrupts enabled        */
 
 /* FIXME
  *
@@ -319,6 +313,8 @@
 #define CONFIG_SYS_MDMRS_VAL       0x00000000
 #define CONFIG_SYS_MDREFR_VAL      0x00403018  /* Initial setting, individual bits set in lowlevel_init.S */
 #endif
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
 
 /*
  * PCMCIA and CF Interfaces (NOT USED, these values from lubbock init)
diff --git a/include/configs/csb226.h b/include/configs/csb226.h
index ae05734..72e47ce 100644
--- a/include/configs/csb226.h
+++ b/include/configs/csb226.h
@@ -45,7 +45,7 @@
 
 /* we will never enable dcache, because we have to setup MMU first */
 #define CONFIG_SYS_NO_DCACHE
-
+#define	CONFIG_SYS_TEXT_BASE	0x0
 /*
  * Hardware drivers
  */
@@ -458,6 +458,9 @@
 
 #define CONFIG_SYS_PSSR_VAL        0x20
 
+#define	CONFIG_SYS_CCCR			CCCR_L27|CCCR_M2|CCCR_N10
+#define	CONFIG_SYS_CKEN			0x0
+
 /*
  * Memory settings
  */
@@ -468,6 +471,8 @@
 #define CONFIG_SYS_MDCNFG_VAL          0x09a909a9
 #define CONFIG_SYS_MDREFR_VAL          0x038ff030
 #define CONFIG_SYS_MDMRS_VAL           0x00220022
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
 
 /*
  * PCMCIA and CF Interfaces
diff --git a/include/configs/delta.h b/include/configs/delta.h
deleted file mode 100644
index d53acbf..0000000
--- a/include/configs/delta.h
+++ /dev/null
@@ -1,267 +0,0 @@
-/*
- * Configuation settings for the Delta board.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_CPU_MONAHANS	1	/* Intel Monahan CPU    */
-#define	CONFIG_CPU_PXA320
-#define CONFIG_DELTA		1	/* Delta board       */
-
-/* #define CONFIG_LCD		1 */
-#ifdef CONFIG_LCD
-#define CONFIG_SHARP_LM8V31
-#endif
-#define BOARD_LATE_INIT		1
-
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-#undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */
-
-/* we will never enable dcache, because we have to setup MMU first */
-#define CONFIG_SYS_NO_DCACHE
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN	    (CONFIG_ENV_SIZE + 256*1024)
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-
-/*
- * Hardware drivers
- */
-#undef TURN_ON_ETHERNET
-#ifdef TURN_ON_ETHERNET
-# define CONFIG_DRIVER_SMC91111 1
-# define CONFIG_SMC91111_BASE   0x14000300
-# define CONFIG_SMC91111_EXT_PHY
-# define CONFIG_SMC_USE_32_BIT
-# undef CONFIG_SMC_USE_IOFUNCS          /* just for use with the kernel */
-#endif
-
-#define CONFIG_HARD_I2C		1	/* required for DA9030 access */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE		1	/* I2C controllers address */
-#define DA9030_I2C_ADDR		0x49	/* I2C address of DA9030 */
-#define CONFIG_SYS_DA9030_EXTON_DELAY	100000	/* wait x us after DA9030 reset via EXTON */
-#define CONFIG_SYS_I2C_INIT_BOARD	1
-/* #define CONFIG_HW_WATCHDOG	1	/\* Required for hitting the DA9030 WD *\/ */
-
-#define DELTA_CHECK_KEYBD	1	/* check for keys pressed during boot */
-#define CONFIG_PREBOOT		"\0"
-
-#ifdef DELTA_CHECK_KEYBD
-# define KEYBD_DATALEN		4	/* we have four keys */
-# define KEYBD_KP_DKIN0		0x1	/* vol+ */
-# define KEYBD_KP_DKIN1		0x2	/* vol- */
-# define KEYBD_KP_DKIN2		0x3	/* multi */
-# define KEYBD_KP_DKIN5		0x4	/* SWKEY_GN */
-#endif /* DELTA_CHECK_KEYBD */
-
-/*
- * select serial console configuration
- */
-#define CONFIG_PXA_SERIAL
-#define CONFIG_FFUART		1
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_BAUDRATE		115200
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#ifdef TURN_ON_ETHERNET
-
-#define CONFIG_CMD_PING
-
-#else
-
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_I2C
-
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_FLASH
-#undef CONFIG_CMD_IMLS
-
-#endif
-
-/* USB */
-#define CONFIG_USB_OHCI_NEW	1
-#define CONFIG_USB_STORAGE      1
-#define CONFIG_DOS_PARTITION    1
-
-#include <asm/arch/pxa-regs.h> /* for OHCI_REGS_BASE */
-
-#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
-#define CONFIG_SYS_USB_OHCI_CPU_INIT	1
-#define CONFIG_SYS_USB_OHCI_REGS_BASE	OHCI_REGS_BASE
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"delta"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	3
-
-#define CONFIG_BOOTDELAY	-1
-#define CONFIG_ETHADDR		08:00:3e:26:0a:5b
-#define CONFIG_NETMASK		255.255.0.0
-#define CONFIG_IPADDR		192.168.0.21
-#define CONFIG_SERVERIP		192.168.0.250
-#define CONFIG_BOOTCOMMAND	"bootm 80000"
-#define CONFIG_BOOTARGS		"root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200"
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_TIMESTAMP
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_HUSH_PARSER		1
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-
-#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT		"$ "		/* Monitor Command Prompt */
-#else
-#define CONFIG_SYS_PROMPT		"=> "		/* Monitor Command Prompt */
-#endif
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_DEVICE_NULLDEV	1
-
-#define CONFIG_SYS_MEMTEST_START	0x80400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x80800000	/* 4 ... 8 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */
-
-#define CONFIG_SYS_HZ			1000
-
-/* Monahans Core Frequency */
-#define CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO		16 /* valid values: 8, 16, 24, 31 */
-#define CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO	1  /* valid values: 1, 2 */
-
-
-						/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
-#ifdef CONFIG_MMC
-#define CONFIG_PXA_MMC
-#define CONFIG_CMD_MMC
-#define CONFIG_SYS_MMC_BASE		0xF0000000
-#endif
-
-/*
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
-#endif
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS	4	   /* we have 2 banks of DRAM */
-#define PHYS_SDRAM_1		0x80000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE	0x1000000  /* 64 MB */
-#define PHYS_SDRAM_2		0x81000000 /* SDRAM Bank #2 */
-#define PHYS_SDRAM_2_SIZE	0x1000000  /* 64 MB */
-#define PHYS_SDRAM_3		0x82000000 /* SDRAM Bank #3 */
-#define PHYS_SDRAM_3_SIZE	0x1000000  /* 64 MB */
-#define PHYS_SDRAM_4		0x83000000 /* SDRAM Bank #4 */
-#define PHYS_SDRAM_4_SIZE	0x1000000  /* 64 MB */
-
-#define CONFIG_SYS_DRAM_BASE		0x80000000 /* at CS0 */
-#define CONFIG_SYS_DRAM_SIZE		0x04000000 /* 64 MB Ram */
-
-#undef CONFIG_SYS_SKIP_DRAM_SCRUB
-
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define	CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_GBL_DATA_SIZE + PHYS_SDRAM_1)
-
-/*
- * NAND Flash
- */
-#define CONFIG_SYS_NAND0_BASE		0x0 /* 0x43100040 */ /* 0x10000000 */
-#undef CONFIG_SYS_NAND1_BASE
-
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND0_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices */
-
-/* nand timeout values */
-#define CONFIG_SYS_NAND_PROG_ERASE_TO	3000
-#define CONFIG_SYS_NAND_OTHER_TO	100
-#define CONFIG_SYS_NAND_SENDCMD_RETRY	3
-#undef NAND_ALLOW_ERASE_ALL	/* Allow erasing bad blocks - don't use */
-
-/* NAND Timing Parameters (in ns) */
-#define NAND_TIMING_tCH		10
-#define NAND_TIMING_tCS		0
-#define NAND_TIMING_tWH		20
-#define NAND_TIMING_tWP		40
-
-#define NAND_TIMING_tRH		20
-#define NAND_TIMING_tRP		40
-
-#define NAND_TIMING_tR		11123
-#define NAND_TIMING_tWHR	100
-#define NAND_TIMING_tAR		10
-
-/* NAND debugging */
-#define CONFIG_SYS_DFC_DEBUG1 /* usefull */
-#undef CONFIG_SYS_DFC_DEBUG2  /* noisy */
-#undef CONFIG_SYS_DFC_DEBUG3  /* extremly noisy  */
-
-#define CONFIG_MTD_DEBUG
-#define CONFIG_MTD_DEBUG_VERBOSE 1
-
-#define CONFIG_SYS_NO_FLASH		1
-
-#define CONFIG_ENV_IS_IN_NAND	1
-#define CONFIG_ENV_OFFSET		0x40000
-#define CONFIG_ENV_OFFSET_REDUND	0x44000
-#define CONFIG_ENV_SIZE		0x4000
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/innokom.h b/include/configs/innokom.h
index 007cceb..01522cd 100644
--- a/include/configs/innokom.h
+++ b/include/configs/innokom.h
@@ -40,6 +40,8 @@
 #undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff      */
 					/* for timer/console/ethernet       */
 
+#define	CONFIG_SYS_TEXT_BASE	0x0
+
 /* we will never enable dcache, because we have to setup MMU first */
 #define CONFIG_SYS_NO_DCACHE
 
@@ -347,6 +349,9 @@
  */
 #define CONFIG_SYS_PSSR_VAL		0x37
 
+#define	CONFIG_SYS_CCCR			CCCR_L27|CCCR_M2|CCCR_N10
+#define	CONFIG_SYS_CKEN			0x0
+
 /*
  * Memory settings
  *
@@ -480,6 +485,9 @@
 #define CONFIG_SYS_MCIO0_VAL		0x00000000
 #define CONFIG_SYS_MCIO1_VAL		0x00000000
 
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
+
 /*
 #define CSB226_USER_LED0	0x00000008
 #define CSB226_USER_LED1	0x00000010
diff --git a/include/configs/lubbock.h b/include/configs/lubbock.h
index 3a99ec2..62f9691 100644
--- a/include/configs/lubbock.h
+++ b/include/configs/lubbock.h
@@ -43,7 +43,7 @@
 #define CONFIG_MMC
 #define BOARD_LATE_INIT		1
 #define CONFIG_DOS_PARTITION
-
+#define	CONFIG_SYS_TEXT_BASE	0x0
 #undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */
 
 /* we will never enable dcache, because we have to setup MMU first */
@@ -202,6 +202,9 @@
 
 #define CONFIG_SYS_PSSR_VAL		0x20
 
+#define	CONFIG_SYS_CCCR			CCCR_L27|CCCR_M2|CCCR_N10
+#define	CONFIG_SYS_CKEN			0x0
+
 /*
  * Memory settings
  */
@@ -212,6 +215,9 @@
 #define CONFIG_SYS_MDREFR_VAL		0x00018018
 #define CONFIG_SYS_MDMRS_VAL		0x00000000
 
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
+
 /*
  * PCMCIA and CF Interfaces
  */
diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h
index 1062765..9e48857 100644
--- a/include/configs/lwmon.h
+++ b/include/configs/lwmon.h
@@ -349,32 +349,32 @@
 
 /* List of I2C addresses to be verified by POST */
 #ifdef CONFIG_USE_FRAM
-#define I2C_ADDR_LIST	{  /*	CONFIG_SYS_I2C_AUDIO_ADDR, */	\
-				CONFIG_SYS_I2C_SYSMON_ADDR,	\
-				CONFIG_SYS_I2C_RTC_ADDR,	\
-				CONFIG_SYS_I2C_POWER_A_ADDR,	\
-				CONFIG_SYS_I2C_POWER_B_ADDR,	\
-				CONFIG_SYS_I2C_KEYBD_ADDR,	\
-				CONFIG_SYS_I2C_PICIO_ADDR,	\
-				CONFIG_SYS_I2C_EEPROM_ADDR,	\
-			}
+#define CONFIG_SYS_POST_I2C_ADDRS	{/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
+					 CONFIG_SYS_I2C_SYSMON_ADDR,	\
+					 CONFIG_SYS_I2C_RTC_ADDR,	\
+					 CONFIG_SYS_I2C_POWER_A_ADDR,	\
+					 CONFIG_SYS_I2C_POWER_B_ADDR,	\
+					 CONFIG_SYS_I2C_KEYBD_ADDR,	\
+					 CONFIG_SYS_I2C_PICIO_ADDR,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR,	\
+					}
 #else	/* Use EEPROM - which show up on 8 consequtive addresses */
-#define I2C_ADDR_LIST	{  /*	CONFIG_SYS_I2C_AUDIO_ADDR, */	\
-				CONFIG_SYS_I2C_SYSMON_ADDR,	\
-				CONFIG_SYS_I2C_RTC_ADDR,	\
-				CONFIG_SYS_I2C_POWER_A_ADDR,	\
-				CONFIG_SYS_I2C_POWER_B_ADDR,	\
-				CONFIG_SYS_I2C_KEYBD_ADDR,	\
-				CONFIG_SYS_I2C_PICIO_ADDR,	\
-				CONFIG_SYS_I2C_EEPROM_ADDR+0,	\
-				CONFIG_SYS_I2C_EEPROM_ADDR+1,	\
-				CONFIG_SYS_I2C_EEPROM_ADDR+2,	\
-				CONFIG_SYS_I2C_EEPROM_ADDR+3,	\
-				CONFIG_SYS_I2C_EEPROM_ADDR+4,	\
-				CONFIG_SYS_I2C_EEPROM_ADDR+5,	\
-				CONFIG_SYS_I2C_EEPROM_ADDR+6,	\
-				CONFIG_SYS_I2C_EEPROM_ADDR+7,	\
-			}
+#define CONFIG_SYS_POST_I2C_ADDRS	{/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
+					 CONFIG_SYS_I2C_SYSMON_ADDR,	\
+					 CONFIG_SYS_I2C_RTC_ADDR,	\
+					 CONFIG_SYS_I2C_POWER_A_ADDR,	\
+					 CONFIG_SYS_I2C_POWER_B_ADDR,	\
+					 CONFIG_SYS_I2C_KEYBD_ADDR,	\
+					 CONFIG_SYS_I2C_PICIO_ADDR,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR+0,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR+1,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR+2,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR+3,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR+4,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR+5,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR+6,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR+7,	\
+					}
 #endif	/* CONFIG_USE_FRAM */
 
 /*-----------------------------------------------------------------------
diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index a4e92cc..63e22d4 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -306,14 +306,13 @@
 #define CONFIG_SYS_I2C_KEYBD_ADDR	0x56	/* PIC LWE keyboard		*/
 #define CONFIG_SYS_I2C_DSPIC_IO_ADDR	0x57	/* PIC I/O addr               */
 
-#define I2C_ADDR_LIST	{						\
-			CONFIG_SYS_I2C_RTC_ADDR,			\
-			CONFIG_SYS_I2C_EEPROM_CPU_ADDR,			\
-			CONFIG_SYS_I2C_EEPROM_MB_ADDR,			\
-			CONFIG_SYS_I2C_DSPIC_ADDR,			\
-			CONFIG_SYS_I2C_DSPIC_2_ADDR,			\
-			CONFIG_SYS_I2C_DSPIC_KEYB_ADDR,			\
-			CONFIG_SYS_I2C_DSPIC_IO_ADDR }
+#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_RTC_ADDR,	\
+					 CONFIG_SYS_I2C_EEPROM_CPU_ADDR,\
+					 CONFIG_SYS_I2C_EEPROM_MB_ADDR,	\
+					 CONFIG_SYS_I2C_DSPIC_ADDR,	\
+					 CONFIG_SYS_I2C_DSPIC_2_ADDR,	\
+					 CONFIG_SYS_I2C_DSPIC_KEYB_ADDR,\
+					 CONFIG_SYS_I2C_DSPIC_IO_ADDR }
 
 /*
  * Pass open firmware flat tree
diff --git a/include/configs/palmld.h b/include/configs/palmld.h
index 926728b..a2310a9 100644
--- a/include/configs/palmld.h
+++ b/include/configs/palmld.h
@@ -34,6 +34,7 @@
 #define	CONFIG_ENV_OVERWRITE
 #define	CONFIG_SYS_MALLOC_LEN		(128*1024)
 #define	CONFIG_SYS_GBL_DATA_SIZE	128
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 #define	CONFIG_BOOTCOMMAND						\
 	"if mmcinfo && fatload mmc 0 0xa0000000 uboot.script ; then "	\
diff --git a/include/configs/palmtc.h b/include/configs/palmtc.h
index fe87648..40ab0bf 100644
--- a/include/configs/palmtc.h
+++ b/include/configs/palmtc.h
@@ -36,6 +36,7 @@
 #define	CONFIG_ENV_OVERWRITE
 #define	CONFIG_SYS_MALLOC_LEN		(128*1024)
 #define	CONFIG_SYS_GBL_DATA_SIZE	128
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 #define	CONFIG_BOOTCOMMAND						\
 	"if mmc init && fatload mmc 0 0xa0000000 uboot.script ; then "	\
diff --git a/include/configs/pleb2.h b/include/configs/pleb2.h
index 3b6e60a..b366f38 100644
--- a/include/configs/pleb2.h
+++ b/include/configs/pleb2.h
@@ -39,6 +39,7 @@
 #undef CONFIG_LCD
 #undef CONFIG_MMC
 #define BOARD_LATE_INIT		1
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 #undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */
 
@@ -155,15 +156,9 @@
 /*
  * Physical Memory Map
  */
-#define CONFIG_NR_DRAM_BANKS	4	   /* we have 2 banks of DRAM */
+#define CONFIG_NR_DRAM_BANKS	1	   /* we have 1 bank of DRAM */
 #define PHYS_SDRAM_1		0xa0000000 /* SDRAM Bank #1 */
 #define PHYS_SDRAM_1_SIZE	0x02000000 /* 32 MB */
-#define PHYS_SDRAM_2		0xa4000000 /* SDRAM Bank #2 */
-#define PHYS_SDRAM_2_SIZE	0x00000000 /* 0 MB */
-#define PHYS_SDRAM_3		0xa8000000 /* SDRAM Bank #3 */
-#define PHYS_SDRAM_3_SIZE	0x00000000 /* 0 MB */
-#define PHYS_SDRAM_4		0xac000000 /* SDRAM Bank #4 */
-#define PHYS_SDRAM_4_SIZE	0x00000000 /* 0 MB */
 
 #define PHYS_FLASH_1		0x00000000 /* Flash Bank #1 */
 #define PHYS_FLASH_2		0x04000000 /* Flash Bank #2 */
@@ -213,9 +208,9 @@
 #define CONFIG_SYS_GAFR2_U_VAL		0x00000000
 
 #define CONFIG_SYS_PSSR_VAL		0x20
-#define CONFIG_SYS_CCCR_VAL	    0x00000141	/* 100 MHz memory, 200 MHz CPU	*/
-#define CONFIG_SYS_CKEN_VAL	    0x00000060	/* FFUART and STUART enabled	*/
-#define CONFIG_SYS_ICMR_VAL	    0x00000000	/* No interrupts enabled	*/
+#define CONFIG_SYS_CCCR		    0x00000141	/* 100 MHz memory, 200 MHz CPU	*/
+#define CONFIG_SYS_CKEN		    0x00000060	/* FFUART and STUART enabled	*/
+#define CONFIG_SYS_ICMR		    0x00000000	/* No interrupts enabled	*/
 
 /*
  * Memory settings
@@ -231,6 +226,9 @@
 					   /* bits set in lowlevel_init.S	*/
 #define CONFIG_SYS_MDMRS_VAL		0x00000000
 
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
+
 /*
  * PCMCIA and CF Interfaces
  */
diff --git a/include/configs/pxa255_idp.h b/include/configs/pxa255_idp.h
index 4581674..b4327c6 100644
--- a/include/configs/pxa255_idp.h
+++ b/include/configs/pxa255_idp.h
@@ -43,6 +43,7 @@
  */
 #undef CONFIG_SKIP_LOWLEVEL_INIT			/* define for developing */
 #undef CONFIG_SKIP_RELOCATE_UBOOT			/* define for developing */
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 /*
  * define the following to enable debug blinks.  A debug blink function
@@ -271,7 +272,7 @@
 /*
  * Physical Memory Map
  */
-#define CONFIG_NR_DRAM_BANKS	4	   /* we have 1 banks of DRAM */
+#define CONFIG_NR_DRAM_BANKS	1	   /* we have 1 bank of DRAM */
 #define PHYS_SDRAM_1		0xa0000000 /* SDRAM Bank #1 */
 #define PHYS_SDRAM_1_SIZE	0x04000000 /* 64 MB */
 #define PHYS_SDRAM_2		0xa4000000 /* SDRAM Bank #2 */
@@ -317,6 +318,9 @@
 
 #define CONFIG_SYS_PSSR_VAL		0x20
 
+#define	CONFIG_SYS_CCCR			CCCR_L27|CCCR_M2|CCCR_N10
+#define	CONFIG_SYS_CKEN			0x0
+
 /*
  * Memory settings
  */
@@ -326,6 +330,8 @@
 #define CONFIG_SYS_MDCNFG_VAL		0x090009C9
 #define CONFIG_SYS_MDREFR_VAL		0x0085C017
 #define CONFIG_SYS_MDMRS_VAL		0x00220022
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
 
 /*
  * PCMCIA and CF Interfaces
diff --git a/include/configs/sh7785lcr.h b/include/configs/sh7785lcr.h
index 2c18e2f..6627f99 100644
--- a/include/configs/sh7785lcr.h
+++ b/include/configs/sh7785lcr.h
@@ -62,8 +62,10 @@
 
 /* MEMORY */
 #if defined(CONFIG_SH_32BIT)
-#define SH7785LCR_SDRAM_PHYS_BASE	(0x48000000)
-#define SH7785LCR_SDRAM_BASE		(0x88000000)
+/* 0x40000000 - 0x47FFFFFF does not use */
+#define CONFIG_SH_SDRAM_OFFSET		(0x8000000)
+#define SH7785LCR_SDRAM_PHYS_BASE	(0x40000000 + CONFIG_SH_SDRAM_OFFSET)
+#define SH7785LCR_SDRAM_BASE		(0x80000000 + CONFIG_SH_SDRAM_OFFSET)
 #define SH7785LCR_SDRAM_SIZE		(384 * 1024 * 1024)
 #define SH7785LCR_FLASH_BASE_1		(0xa0000000)
 #define SH7785LCR_FLASH_BANK_SIZE	(64 * 1024 * 1024)
diff --git a/include/configs/spieval.h b/include/configs/spieval.h
index b5ac168..880c8a3 100644
--- a/include/configs/spieval.h
+++ b/include/configs/spieval.h
@@ -271,10 +271,10 @@
 
 /* List of I2C addresses to be verified by POST */
 #if defined (CONFIG_MINIFAP)
-#undef I2C_ADDR_LIST
-#define I2C_ADDR_LIST	{	CONFIG_SYS_I2C_EEPROM_ADDR,	\
-				CONFIG_SYS_I2C_HWMON_ADDR,	\
-				CONFIG_SYS_I2C_SLAVE }
+#undef CONFIG_SYS_POST_I2C_ADDRS
+#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_EEPROM_ADDR,	\
+					 CONFIG_SYS_I2C_HWMON_ADDR,	\
+					 CONFIG_SYS_I2C_SLAVE}
 #endif
 
 /*
diff --git a/include/configs/trizepsiv.h b/include/configs/trizepsiv.h
index 4743495..ac3566c 100644
--- a/include/configs/trizepsiv.h
+++ b/include/configs/trizepsiv.h
@@ -44,6 +44,7 @@
 
 #define CONFIG_MMC		1
 #define BOARD_LATE_INIT		1
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 #undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */
 
diff --git a/include/configs/vision2.h b/include/configs/vision2.h
index a2ecbe5..d2d9565 100644
--- a/include/configs/vision2.h
+++ b/include/configs/vision2.h
@@ -211,4 +211,18 @@
 
 #define CONFIG_SYS_NO_FLASH
 
+/*
+ * Framebuffer and LCD
+ */
+#define CONFIG_PREBOOT
+#define CONFIG_LCD
+#define CONFIG_VIDEO_MX5
+#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define LCD_BPP		LCD_COLOR16
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+
 #endif				/* __CONFIG_H */
diff --git a/include/configs/vpac270.h b/include/configs/vpac270.h
index c9d9c69..3107014 100644
--- a/include/configs/vpac270.h
+++ b/include/configs/vpac270.h
@@ -27,6 +27,7 @@
  */
 #define	CONFIG_PXA27X		1	/* Marvell PXA270 CPU */
 #define	CONFIG_VPAC270		1	/* Voipac PXA270 board */
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 /*
  * Environment settings
diff --git a/include/configs/wepep250.h b/include/configs/wepep250.h
deleted file mode 100644
index a961a27..0000000
--- a/include/configs/wepep250.h
+++ /dev/null
@@ -1,199 +0,0 @@
-/*
- * Copyright (C) 2003 ETC s.r.o.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * Written by Peter Figuli <peposh@etc.sk>, 2003.
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_PXA250          1        /* this is an PXA250 CPU     */
-#define CONFIG_WEPEP250        1        /* config for wepep250 board */
-#undef  CONFIG_USE_IRQ                  /* don't need use IRQ/FIQ    */
-
-/* we will never enable dcache, because we have to setup MMU first */
-#define CONFIG_SYS_NO_DCACHE
-
-/*
- * Select serial console configuration
- */
-#define CONFIG_PXA_SERIAL
-#define CONFIG_BTUART          1       /* BTUART is default on WEP dev board */
-#define CONFIG_BAUDRATE   115200
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_SOURCE
-
-
-/*
- * Boot options. Setting delay to -1 stops autostart count down.
- * NOTE: Sending parameters to kernel depends on kernel version and
- * 2.4.19-rmk6-pxa1 patch used while my u-boot coding didn't accept
- * parameters at all! Do not get confused by them so.
- */
-#define CONFIG_BOOTDELAY   -1
-#define CONFIG_BOOTARGS    "root=/dev/mtdblock2 mem=32m console=ttyS01,115200n8"
-#define CONFIG_BOOTCOMMAND "bootm 40000"
-
-
-/*
- * General options for u-boot. Modify to save memory foot print
- */
-#define CONFIG_SYS_LONGHELP                                  /* undef saves memory  */
-#define CONFIG_SYS_PROMPT              "WEP> "               /* prompt string       */
-#define CONFIG_SYS_CBSIZE              256                   /* console I/O buffer  */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* print buffer size   */
-#define CONFIG_SYS_MAXARGS             16                    /* max command args    */
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE            /* boot args buf size  */
-
-#define CONFIG_SYS_MEMTEST_START       0xa0400000            /* memtest test area   */
-#define CONFIG_SYS_MEMTEST_END         0xa0800000
-
-#define CONFIG_SYS_HZ			1000
-#define CONFIG_SYS_CPUSPEED            0x141        /* core clock - register value  */
-
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Definitions related to passing arguments to kernel.
- */
-#define CONFIG_CMDLINE_TAG           1   /* send commandline to Kernel       */
-#define CONFIG_SETUP_MEMORY_TAGS     1   /* send memory definition to kernel */
-#undef  CONFIG_INITRD_TAG                /* do not send initrd params        */
-#undef  CONFIG_VFD                       /* do not send framebuffer setup    */
-
-
-/*
- * Malloc pool need to host env + 128 Kb reserve for other allocations.
- */
-#define CONFIG_SYS_MALLOC_LEN	  (CONFIG_ENV_SIZE + (128<<10) )
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-
-#define CONFIG_STACKSIZE        (120<<10)      /* stack size */
-
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ    (4<<10)        /* IRQ stack  */
-#define CONFIG_STACKSIZE_FIQ    (4<<10)        /* FIQ stack  */
-#endif
-
-/*
- * SDRAM Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS    1                /* we have 1 bank of SDRAM */
-#define WEP_SDRAM_1            0xa0000000        /* SDRAM bank #1           */
-#define WEP_SDRAM_1_SIZE       0x02000000        /* 32 MB ( 2 chip )        */
-#define WEP_SDRAM_2            0xa2000000        /* SDRAM bank #2           */
-#define WEP_SDRAM_2_SIZE       0x00000000        /* 0 MB                    */
-#define WEP_SDRAM_3            0xa8000000        /* SDRAM bank #3           */
-#define WEP_SDRAM_3_SIZE       0x00000000        /* 0 MB                    */
-#define WEP_SDRAM_4            0xac000000        /* SDRAM bank #4           */
-#define WEP_SDRAM_4_SIZE       0x00000000        /* 0 MB                    */
-
-#define CONFIG_SYS_DRAM_BASE           0xa0000000
-#define CONFIG_SYS_DRAM_SIZE           0x02000000
-
-/* Uncomment used SDRAM chip */
-#define WEP_SDRAM_K4S281633
-/*#define WEP_SDRAM_K4S561633*/
-
-
-/*
- * Configuration for FLASH memory
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* FLASH banks count (not chip count)*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* number of sector in FLASH bank    */
-#define WEP_FLASH_BUS_WIDTH	4	/* we use 32 bit FLASH memory...     */
-#define WEP_FLASH_INTERLEAVE	2	/* ... made of 2 chips */
-#define WEP_FLASH_BANK_SIZE  0x2000000  /* size of one flash bank*/
-#define WEP_FLASH_SECT_SIZE  0x0040000  /* size of erase sector */
-#define WEP_FLASH_BASE       0x0000000  /* location of flash memory */
-#define WEP_FLASH_UNLOCK        1       /* perform hw unlock first */
-
-
-/* This should be defined if CFI FLASH device is present. Actually benefit
-   is not so clear to me. In other words we can provide more informations
-   to user, but this expects more complex flash handling we do not provide
-   now.*/
-#undef  CONFIG_SYS_FLASH_CFI
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT    (2*CONFIG_SYS_HZ)    /* timeout for Erase operation */
-#define CONFIG_SYS_FLASH_WRITE_TOUT    (2*CONFIG_SYS_HZ)    /* timeout for Write operation */
-
-#define CONFIG_SYS_FLASH_BASE          WEP_FLASH_BASE
-
-/*
- * This is setting for JFFS2 support in u-boot.
- * Right now there is no gain for user, but later on booting kernel might be
- * possible. Consider using XIP kernel running from flash to save RAM
- * footprint.
- * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
- */
-#define CONFIG_SYS_JFFS2_FIRST_BANK		0
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR		5
-#define CONFIG_SYS_JFFS2_NUM_BANKS		1
-
-/*
- * Environment setup. Definitions of monitor location and size with
- * definition of environment setup ends up in 2 possibilities.
- * 1. Embeded environment - in u-boot code is space for environment
- * 2. Environment is read from predefined sector of flash
- * Right now we support 2. possiblity, but expecting no env placed
- * on mentioned address right now. This also needs to provide whole
- * sector for it - for us 256Kb is really waste of memory. U-boot uses
- * default env. and until kernel parameters could be sent to kernel
- * env. has no sense to us.
- */
-
-#define CONFIG_SYS_MONITOR_BASE	PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_LEN		0x20000		/* 128kb ( 1 flash sector )  */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		0x20000	        /* absolute address for now  */
-#define CONFIG_ENV_SIZE		0x2000
-
-#define	PHYS_SDRAM_1			WEP_SDRAM_1
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define	CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_GBL_DATA_SIZE + PHYS_SDRAM_1)
-
-#undef  CONFIG_ENV_OVERWRITE                    /* env is not writable now   */
-
-/*
- * Well this has to be defined, but on the other hand it is used differently
- * one may expect. For instance loadb command do not cares :-)
- * So advice is - do not relay on this...
- */
-#define CONFIG_SYS_LOAD_ADDR        0x40000
-
-#endif  /* __CONFIG_H */
diff --git a/include/configs/xaeniax.h b/include/configs/xaeniax.h
index 67d4106..18b68fa 100644
--- a/include/configs/xaeniax.h
+++ b/include/configs/xaeniax.h
@@ -42,6 +42,7 @@
  */
 #define CONFIG_PXA250		1	/* This is an PXA255 CPU    */
 #define CONFIG_XAENIAX		1	/* on a xaeniax board	    */
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 
 #define BOARD_LATE_INIT		1
@@ -437,8 +438,9 @@
  */
 #define CONFIG_SYS_PSSR_VAL		0x00000030
 
-#define CONFIG_SYS_CKEN_VAL            0x00000080  /*  */
-#define CONFIG_SYS_ICMR_VAL            0x00000000  /* No interrupts enabled        */
+#define CONFIG_SYS_CKEN			0x00000080  /*  */
+#define CONFIG_SYS_ICMR			0x00000000  /* No interrupts enabled        */
+#define	CONFIG_SYS_CCCR			CCCR_L27|CCCR_M2|CCCR_N10
 
 
 /*
@@ -562,6 +564,9 @@
  */
 #define CONFIG_SYS_MDMRS_VAL		0x00320032
 
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
+
 /*
  * PCMCIA and CF Interfaces
  */
diff --git a/include/configs/xm250.h b/include/configs/xm250.h
index 2ff9a28..ea52454 100644
--- a/include/configs/xm250.h
+++ b/include/configs/xm250.h
@@ -35,6 +35,7 @@
 #define CONFIG_PXA250	       1	/* This is an PXA250 CPU	*/
 #define CONFIG_XM250	       1	/* on a MicroSys XM250 Board	*/
 #undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff	*/
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 /* we will never enable dcache, because we have to setup MMU first */
 #define CONFIG_SYS_NO_DCACHE
@@ -322,9 +323,9 @@
  * Clocks, power control and interrupts
  */
 #define CONFIG_SYS_PSSR_VAL	    0x00000030
-#define CONFIG_SYS_CCCR_VAL	    0x00000161	/* 100 MHz memory, 400 MHz CPU, 400 Turbo  */
-#define CONFIG_SYS_CKEN_VAL	    0x000141ec	/* FFUART and STUART enabled	*/
-#define CONFIG_SYS_ICMR_VAL	    0x00000000	/* No interrupts enabled	*/
+#define CONFIG_SYS_CCCR		    0x00000161	/* 100 MHz memory, 400 MHz CPU, 400 Turbo  */
+#define CONFIG_SYS_CKEN		    0x000141ec	/* FFUART and STUART enabled	*/
+#define CONFIG_SYS_ICMR		    0x00000000	/* No interrupts enabled	*/
 
 /* FIXME
  *
@@ -343,6 +344,8 @@
 #define CONFIG_SYS_MDCNFG_VAL	    0x000009c9
 #define CONFIG_SYS_MDMRS_VAL	    0x00220022
 #define CONFIG_SYS_MDREFR_VAL	    0x000da018	/* Initial setting, individual bits set in lowlevel_init.S */
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
 
 /*
  * PCMCIA and CF Interfaces (NOT USED, these values from lubbock init)
diff --git a/include/configs/XPEDITE1000.h b/include/configs/xpedite1000.h
index 5605849..d0f9363 100644
--- a/include/configs/XPEDITE1000.h
+++ b/include/configs/xpedite1000.h
@@ -33,6 +33,7 @@
 /* High Level Configuration Options */
 #define CONFIG_XPEDITE1000	1
 #define CONFIG_SYS_BOARD_NAME	"XPedite1000"
+#define CONFIG_SYS_FORM_PMC	1
 #define CONFIG_4xx		1		/* ... PPC4xx family */
 #define CONFIG_440		1
 #define CONFIG_440GX		1		/* 440 GX */
@@ -341,8 +342,8 @@ extern void out32(unsigned int, unsigned long);
 	"misc_args=ip=on\0"						\
 	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 	"bootfile=/home/user/file\0"					\
-	"osfile=/home/user/uImage-XPedite1000\0"			\
-	"fdtfile=/home/user/xpedite1000.dtb\0"				\
+	"osfile=/home/user/board.uImage\0"				\
+	"fdtfile=/home/user/board.dtb\0"				\
 	"ubootfile=/home/user/u-boot.bin\0"				\
 	"fdtaddr=c00000\0"						\
 	"osaddr=0x1000000\0"						\
diff --git a/include/configs/XPEDITE5170.h b/include/configs/xpedite517x.h
index 1851997..8df9edd 100644
--- a/include/configs/XPEDITE5170.h
+++ b/include/configs/xpedite517x.h
@@ -22,7 +22,7 @@
  */
 
 /*
- * xpedite5170 board configuration file
+ * xpedite517x board configuration file
  */
 #ifndef __CONFIG_H
 #define __CONFIG_H
@@ -34,6 +34,7 @@
 #define CONFIG_MPC8641		1	/* MPC8641 specific */
 #define CONFIG_XPEDITE5140	1	/* MPC8641HPCN board specific */
 #define CONFIG_SYS_BOARD_NAME	"XPedite5170"
+#define CONFIG_SYS_FORM_3U_VPX	1
 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
 #define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
 #define CONFIG_BAT_RW		1	/* Use common BAT rw code */
@@ -107,6 +108,21 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_ALT_MEMTEST
 #define CONFIG_SYS_MEMTEST_START	0x10000000
 #define CONFIG_SYS_MEMTEST_END		0x20000000
+#define CONFIG_POST			(CONFIG_SYS_POST_MEMORY |\
+					 CONFIG_SYS_POST_I2C)
+#define I2C_ADDR_LIST			{CONFIG_SYS_I2C_DS1621_ADDR,	\
+					 CONFIG_SYS_I2C_DS4510_ADDR,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR,	\
+					 CONFIG_SYS_I2C_LM90_ADDR,	\
+					 CONFIG_SYS_I2C_PCA9553_ADDR,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR0,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR1,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR2,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR3,	\
+					 CONFIG_SYS_I2C_PEX8518_ADDR,	\
+					 CONFIG_SYS_I2C_RTC_ADDR}
+/* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */
+#define I2C_ADDR_IGNORE_LIST		{0x50}
 
 /*
  * Memory map
@@ -258,6 +274,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_I2C_DS1621_ADDR	0x48
 #define CONFIG_DTT_DS1621
 #define CONFIG_DTT_SENSORS		{ 0 }
+#define CONFIG_SYS_I2C_LM90_ADDR	0x4c
 
 /* I2C EEPROM - AT24C128B */
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
@@ -281,6 +298,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_I2C_PCA953X_ADDR2	0x1e
 #define CONFIG_SYS_I2C_PCA953X_ADDR3	0x1f
 #define CONFIG_SYS_I2C_PCA953X_ADDR	CONFIG_SYS_I2C_PCA953X_ADDR0
+#define CONFIG_SYS_I2C_PCA9553_ADDR	0x62
 
 /*
  * PU = pulled high, PD = pulled low
@@ -324,18 +342,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 /* PCIE1 - PEX8518 */
-#define CONFIG_SYS_PCIE1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
-#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
 
 /* PCIE2 - VPX P1 */
-#define CONFIG_SYS_PCIE2_MEM_BASE	0xc0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xe8800000
 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000	/* 8M */
 
@@ -545,6 +563,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_CMD_PCA953X
 #define CONFIG_CMD_PCA953X_INFO
 #define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SNTP
@@ -725,8 +744,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 	"misc_args=ip=on\0"						\
 	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 	"bootfile=/home/user/file\0"					\
-	"osfile=/home/user/uImage-XPedite5170\0"			\
-	"fdtfile=/home/user/xpedite5170.dtb\0"				\
+	"osfile=/home/user/board.uImage\0"				\
+	"fdtfile=/home/user/board.dtb\0"				\
 	"ubootfile=/home/user/u-boot.bin\0"				\
 	"fdtaddr=c00000\0"						\
 	"osaddr=0x1000000\0"						\
diff --git a/include/configs/XPEDITE5200.h b/include/configs/xpedite520x.h
index d0e9492..2f31337 100644
--- a/include/configs/XPEDITE5200.h
+++ b/include/configs/xpedite520x.h
@@ -22,7 +22,7 @@
  */
 
 /*
- * xpedite5200 board configuration file
+ * xpedite520x board configuration file
  */
 #ifndef __CONFIG_H
 #define __CONFIG_H
@@ -36,6 +36,7 @@
 #define CONFIG_MPC8548		1
 #define CONFIG_XPEDITE5200	1
 #define CONFIG_SYS_BOARD_NAME	"XPedite5200"
+#define CONFIG_SYS_FORM_PMC_XMC	1
 #define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
 
 #ifndef CONFIG_SYS_TEXT_BASE
@@ -92,6 +93,13 @@
 #define CONFIG_SYS_ALT_MEMTEST
 #define CONFIG_SYS_MEMTEST_START	0x10000000
 #define CONFIG_SYS_MEMTEST_END		0x20000000
+#define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
+					 CONFIG_SYS_POST_I2C)
+#define I2C_ADDR_LIST			{CONFIG_SYS_I2C_MAX1237_ADDR,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR0,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR1,	\
+					 CONFIG_SYS_I2C_RTC_ADDR}
 
 /*
  * Memory map
@@ -250,7 +258,7 @@
 #define CONFIG_SYS_PCA953X_BRD_CFG2		0x04
 #define CONFIG_SYS_PCA953X_XMC_ROOT0		0x08
 #define CONFIG_SYS_PCA953X_FLASH_PASS_CS	0x10
-#define CONFIG_SYS_PCA953X_FLASH_WP		0x20
+#define CONFIG_SYS_PCA953X_NVM_WP		0x20
 #define CONFIG_SYS_PCA953X_MONARCH		0x40
 #define CONFIG_SYS_PCA953X_EREADY		0x80
 
@@ -264,14 +272,17 @@
 #define CONFIG_SYS_PCA953X_P14_IO6		0x40
 #define CONFIG_SYS_PCA953X_P14_IO7		0x80
 
+/* 12-bit ADC used to measure CPU diode */
+#define CONFIG_SYS_I2C_MAX1237_ADDR		0x34
+
 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_BUS		0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BUS
 #define CONFIG_SYS_PCI1_MEM_SIZE	0x40000000	/* 1G */
-#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
+#define CONFIG_SYS_PCI1_IO_BUS		0x00000000
 #define CONFIG_SYS_PCI1_IO_PHYS		0xe8000000
 #define CONFIG_SYS_PCI1_IO_SIZE		0x00800000	/* 1M */
 
@@ -339,6 +350,7 @@
 #define CONFIG_CMD_PCA953X
 #define CONFIG_CMD_PCA953X_INFO
 #define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_SNTP
 #define CONFIG_CMD_REGINFO
@@ -521,8 +533,8 @@
 	"misc_args=ip=on\0"						\
 	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 	"bootfile=/home/user/file\0"					\
-	"osfile=/home/user/uImage-XPedite5200\0"			\
-	"fdtfile=/home/user/xpedite5200.dtb\0"				\
+	"osfile=/home/user/board.uImage\0"				\
+	"fdtfile=/home/user/board.dtb\0"				\
 	"ubootfile=/home/user/u-boot.bin\0"				\
 	"fdtaddr=c00000\0"						\
 	"osaddr=0x1000000\0"						\
diff --git a/include/configs/XPEDITE5370.h b/include/configs/xpedite537x.h
index 629dc0d..e7de13a 100644
--- a/include/configs/XPEDITE5370.h
+++ b/include/configs/xpedite537x.h
@@ -22,7 +22,7 @@
  */
 
 /*
- * xpedite5370 board configuration file
+ * xpedite537x board configuration file
  */
 #ifndef __CONFIG_H
 #define __CONFIG_H
@@ -36,6 +36,7 @@
 #define CONFIG_MPC8572		1
 #define CONFIG_XPEDITE5370	1
 #define CONFIG_SYS_BOARD_NAME	"XPedite5370"
+#define CONFIG_SYS_FORM_3U_VPX	1
 #define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
 
 #ifndef CONFIG_SYS_TEXT_BASE
@@ -110,6 +111,20 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_ALT_MEMTEST
 #define CONFIG_SYS_MEMTEST_START	0x10000000
 #define CONFIG_SYS_MEMTEST_END		0x20000000
+#define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
+					 CONFIG_SYS_POST_I2C)
+#define I2C_ADDR_LIST			{CONFIG_SYS_I2C_DS1621_ADDR,	\
+					 CONFIG_SYS_I2C_DS4510_ADDR,	\
+					 CONFIG_SYS_I2C_EEPROM_ADDR,	\
+					 CONFIG_SYS_I2C_LM90_ADDR,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR0,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR1,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR2,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR3,	\
+					 CONFIG_SYS_I2C_PEX8518_ADDR,	\
+					 CONFIG_SYS_I2C_RTC_ADDR}
+/* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
+#define I2C_ADDR_IGNORE_LIST		{0x50}
 
 /*
  * Memory map
@@ -265,6 +280,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_I2C_DS1621_ADDR	0x48
 #define CONFIG_DTT_DS1621
 #define CONFIG_DTT_SENSORS		{ 0 }
+#define CONFIG_SYS_I2C_LM90_ADDR	0x4c
 
 /* I2C EEPROM - AT24C128B */
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
@@ -334,18 +350,18 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 /* PCIE1 - VPX P1 */
-#define CONFIG_SYS_PCIE1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
-#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
 
 /* PCIE2 - PEX8518 */
-#define CONFIG_SYS_PCIE2_MEM_BASE	0xc0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xe8800000
 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000	/* 8M */
 
@@ -396,6 +412,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_CMD_PCA953X
 #define CONFIG_CMD_PCA953X_INFO
 #define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_SAVEENV
 #define CONFIG_CMD_SNTP
@@ -578,8 +595,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 	"misc_args=ip=on\0"						\
 	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 	"bootfile=/home/user/file\0"					\
-	"osfile=/home/user/uImage-XPedite5370\0"			\
-	"fdtfile=/home/user/xpedite5370.dtb\0"				\
+	"osfile=/home/user/board.uImage\0"				\
+	"fdtfile=/home/user/board.dtb\0"				\
 	"ubootfile=/home/user/u-boot.bin\0"				\
 	"fdtaddr=c00000\0"						\
 	"osaddr=0x1000000\0"						\
diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h
new file mode 100644
index 0000000..a849cf9
--- /dev/null
+++ b/include/configs/xpedite550x.h
@@ -0,0 +1,607 @@
+/*
+ * Copyright 2010 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * xpedite550x board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
+#define CONFIG_P2020		1
+#define CONFIG_XPEDITE550X	1
+#define CONFIG_SYS_BOARD_NAME	"XPedite5500"
+#define CONFIG_SYS_FORM_PMC_XMC	1
+#define CONFIG_PRPMC_PCI_ALIAS	"pci0"	/* Processor PMC interface on pci0 */
+#define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xfff80000
+#endif
+
+#define CONFIG_PCI		1	/* Enable PCI/PCIE */
+#define CONFIG_PCI_PNP		1	/* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
+#define CONFIG_PCIE1		1	/* PCIE controler 1 (PEX8112 or XMC) */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
+#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+#define CONFIG_FSL_ELBC		1
+
+/*
+ * Multicore config
+ */
+#define CONFIG_MP
+#define CONFIG_BPTR_VIRT_ADDR	0xee000000	/* virt boot page address */
+#define CONFIG_MPC8xxx_DISABLE_BPTR		/* Don't leave BPTR enabled */
+
+/*
+ * DDR config
+ */
+#define CONFIG_FSL_DDR3
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#define SPD_EEPROM_ADDRESS1			0x54
+#define SPD_EEPROM_OFFSET		0x200	/* OFFSET of SPD in EEPROM */
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+extern unsigned long get_board_ddr_clk(unsigned long dummy);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
+#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk(0) /* ddrclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR		0xef000000	/* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+
+/*
+ * Diagnostics
+ */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x10000000
+#define CONFIG_SYS_MEMTEST_END		0x20000000
+#define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
+					 CONFIG_SYS_POST_I2C)
+#define I2C_ADDR_LIST			{CONFIG_SYS_I2C_EEPROM_ADDR,	\
+					 CONFIG_SYS_I2C_LM75_ADDR,	\
+					 CONFIG_SYS_I2C_LM90_ADDR,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR0,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR2,	\
+					 CONFIG_SYS_I2C_PCA953X_ADDR3,	\
+					 CONFIG_SYS_I2C_RTC_ADDR}
+
+/*
+ * Memory map
+ * 0x0000_0000 0x7fff_ffff	DDR			2G Cacheable
+ * 0x8000_0000 0xbfff_ffff	PCIe1 Mem		1G non-cacheable
+ * 0xe000_0000 0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
+ * 0xe800_0000 0xe87f_ffff	PCIe1 IO		8M non-cacheable
+ * 0xee00_0000 0xee00_ffff	Boot page translation	4K non-cacheable
+ * 0xef00_0000 0xef0f_ffff	CCSR/IMMR		1M non-cacheable
+ * 0xef80_0000 0xef8f_ffff	NAND Flash		1M non-cacheable
+ * 0xf000_0000 0xf7ff_ffff	NOR Flash 2		128M non-cacheable
+ * 0xf800_0000 0xffff_ffff	NOR Flash 1		128M non-cacheable
+ */
+
+#define CONFIG_SYS_LBC_LCRR	(LCRR_CLKDIV_8 | LCRR_EADC_3)
+
+/*
+ * NAND flash configuration
+ */
+#define CONFIG_SYS_NAND_BASE		0xef800000
+#define CONFIG_SYS_NAND_BASE2		0xef840000 /* Unused at this time */
+#define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE, \
+					 CONFIG_SYS_NAND_BASE2}
+#define CONFIG_SYS_MAX_NAND_DEVICE	2
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_SYS_NAND_QUIET_TEST	/* 2nd NAND flash not always populated */
+#define CONFIG_NAND_FSL_ELBC
+
+/*
+ * NOR flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE		0xf8000000
+#define CONFIG_SYS_FLASH_BASE2		0xf0000000
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
+#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff40000, 0xc0000}, \
+						  {0xf7f40000, 0xc0000} }
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+
+/*
+ * Chip select configuration
+ */
+/* NOR Flash 0 on CS0 */
+#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	| \
+				 BR_PS_16		| \
+				 BR_V)
+#define CONFIG_SYS_OR0_PRELIM	(OR_AM_128MB		| \
+				 OR_GPCM_CSNT		| \
+				 OR_GPCM_XACS		| \
+				 OR_GPCM_ACS_DIV2	| \
+				 OR_GPCM_SCY_8		| \
+				 OR_GPCM_TRLX		| \
+				 OR_GPCM_EHTR		| \
+				 OR_GPCM_EAD)
+
+/* NOR Flash 1 on CS1 */
+#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	| \
+				 BR_PS_16		| \
+				 BR_V)
+#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	| \
+				 (2<<BR_DECC_SHIFT)	| \
+				 BR_PS_8		| \
+				 BR_MS_FCM		| \
+				 BR_V)
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB	| \
+				 OR_FCM_PGS	| \
+				 OR_FCM_CSCT	| \
+				 OR_FCM_CST	| \
+				 OR_FCM_CHT	| \
+				 OR_FCM_SCY_1	| \
+				 OR_FCM_TRLX	| \
+				 OR_FCM_EHTR)
+
+/* NAND flash on CS3 */
+#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	| \
+				 (2<<BR_DECC_SHIFT)	| \
+				 BR_PS_8		| \
+				 BR_MS_FCM		| \
+				 BR_V)
+#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
+
+/*
+ * Use L1 as initial stack
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
+#define CONFIG_SYS_INIT_RAM_END		0x00004000
+
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+#define CONFIG_FDT_FIXUP_PCI_IRQ	1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C				/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C				/* I2C with hardware support */
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
+#define CONFIG_I2C_MULTI_BUS
+
+/* I2C DS7505 temperature sensor */
+#define CONFIG_DTT_LM75
+#define CONFIG_DTT_SENSORS		{ 0 }
+#define CONFIG_SYS_I2C_LM75_ADDR	0x48
+
+/* I2C ADT7461 temperature sensor */
+#define CONFIG_SYS_I2C_LM90_ADDR	0x4C
+
+/* I2C EEPROM - AT24C128B */
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T11		1
+#define CONFIG_SYS_I2C_RTC_ADDR		0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR	2000
+
+/* GPIO */
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_ADDR0	0x18
+#define CONFIG_SYS_I2C_PCA953X_ADDR1	0x1c
+#define CONFIG_SYS_I2C_PCA953X_ADDR2	0x1e
+#define CONFIG_SYS_I2C_PCA953X_ADDR3	0x1f
+#define CONFIG_SYS_I2C_PCA953X_ADDR	CONFIG_SYS_I2C_PCA953X_ADDR0
+
+/*
+ * GPIO pin definitions, PU = pulled high, PD = pulled low
+ */
+/* PCA9557 @ 0x18*/
+#define CONFIG_SYS_PCA953X_C0_SER0_EN		0x01 /* PU; UART0 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER0_MODE		0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
+#define CONFIG_SYS_PCA953X_C0_SER1_EN		0x04 /* PU; UART1 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER1_MODE		0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
+#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS	0x10 /* PU; Boot flash CS select */
+#define CONFIG_SYS_PCA953X_NVM_WP		0x20 /* PU; Write protection (0: disabled, 1: enabled) */
+
+/* PCA9557 @ 0x1e*/
+#define CONFIG_SYS_PCA953X_XMC_GA0		0x01 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_GA1		0x02 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_GA2		0x04 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_WAKE		0x10 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_BIST		0x20 /* Enable XMC BIST */
+#define CONFIG_SYS_PCA953X_PMC_EREADY		0x40 /* PU; PMC PCI eready */
+#define CONFIG_SYS_PCA953X_PMC_MONARCH		0x80 /* PMC monarch mode enable */
+
+/* PCA9557 @ 0x1f */
+#define CONFIG_SYS_PCA953X_MC_GPIO0		0x01 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO1		0x02 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO2		0x04 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO3		0x08 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO4		0x10 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO5		0x20 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO6		0x40 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO7		0x80 /* PU; */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1 - PEX8112 or XMC, depending on build option */
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
+
+
+/*
+ * Networking options
+ */
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#define CONFIG_NET_MULTI	1
+#define CONFIG_TSEC_TBI
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
+#define CONFIG_ETHPRIME		"eTSEC2"
+
+#define CONFIG_TSEC1		1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC1_PHY_ADDR		1
+#define TSEC1_PHYIDX		0
+#define CONFIG_HAS_ETH0
+
+#define CONFIG_TSEC2		1
+#define CONFIG_TSEC2_NAME	"eTSEC2"
+#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_PHY_ADDR		2
+#define TSEC2_PHYIDX		0
+#define CONFIG_HAS_ETH1
+
+#define CONFIG_TSEC3		1
+#define CONFIG_TSEC3_NAME	"eTSEC3"
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_PHY_ADDR		3
+#define TSEC3_PHYIDX		0
+#define CONFIG_HAS_ETH2
+
+/*
+ * USB
+ */
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_DOS_PARTITION
+
+/*
+ * Command configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
+#define CONFIG_CMDLINE_EDITING	1		/* add command line history	*/
+#define CONFIG_AUTO_COMPLETE	1		/* add autocompletion support */
+#define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY	3		/* -1 disables auto-boot */
+#define CONFIG_PANIC_HANG			/* do not reset board on panic */
+#define CONFIG_PREBOOT				/* enable preboot variable */
+#define CONFIG_FIT		1
+#define CONFIG_FIT_VERBOSE	1
+#define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */
+
+/*
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM		0x02		/* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
+#define CONFIG_ENV_SIZE		0x8000
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))
+
+/*
+ * Flash memory map:
+ * fff80000 - ffffffff     Pri U-Boot (512 KB)
+ * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
+ * fff00000 - fff3ffff     Pri FDT (256KB)
+ * fef00000 - ffefffff     Pri OS image (16MB)
+ * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
+ *
+ * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
+ * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
+ * f7f00000 - f7f3ffff     Sec FDT (256KB)
+ * f6f00000 - f7efffff     Sec OS image (16MB)
+ * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
+ */
+#define CONFIG_UBOOT1_ENV_ADDR	MK_STR(0xfff80000)
+#define CONFIG_UBOOT2_ENV_ADDR	MK_STR(0xf7f80000)
+#define CONFIG_FDT1_ENV_ADDR	MK_STR(0xfff00000)
+#define CONFIG_FDT2_ENV_ADDR	MK_STR(0xf7f00000)
+#define CONFIG_OS1_ENV_ADDR	MK_STR(0xfef00000)
+#define CONFIG_OS2_ENV_ADDR	MK_STR(0xf6f00000)
+
+#define CONFIG_PROG_UBOOT1						\
+	"$download_cmd $loadaddr $ubootfile; "				\
+	"if test $? -eq 0; then "					\
+		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
+		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
+		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
+		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
+		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
+		"if test $? -ne 0; then "				\
+			"echo PROGRAM FAILED; "				\
+		"else; "						\
+			"echo PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_UBOOT2						\
+	"$download_cmd $loadaddr $ubootfile; "				\
+	"if test $? -eq 0; then "					\
+		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
+		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
+		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
+		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
+		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
+		"if test $? -ne 0; then "				\
+			"echo PROGRAM FAILED; "				\
+		"else; "						\
+			"echo PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_BOOT_OS_NET						\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"if test -n $fdtaddr; then "				\
+			"$download_cmd $fdtaddr $fdtfile; "		\
+			"if test $? -eq 0; then "			\
+				"bootm $osaddr - $fdtaddr; "		\
+			"else; "					\
+				"echo FDT DOWNLOAD FAILED; "		\
+			"fi; "						\
+		"else; "						\
+			"bootm $osaddr; "				\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_OS1							\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
+		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
+		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo OS PROGRAM FAILED; "			\
+		"else; "						\
+			"echo OS PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_OS2							\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
+		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
+		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo OS PROGRAM FAILED; "			\
+		"else; "						\
+			"echo OS PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_FDT1						\
+	"$download_cmd $fdtaddr $fdtfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
+		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
+		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo FDT PROGRAM FAILED; "			\
+		"else; "						\
+			"echo FDT PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo FDT DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_FDT2						\
+	"$download_cmd $fdtaddr $fdtfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
+		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
+		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo FDT PROGRAM FAILED; "			\
+		"else; "						\
+			"echo FDT PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo FDT DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"autoload=yes\0"						\
+	"download_cmd=tftp\0"						\
+	"console_args=console=ttyS0,115200\0"				\
+	"root_args=root=/dev/nfs rw\0"					\
+	"misc_args=ip=on\0"						\
+	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
+	"bootfile=/home/user/file\0"					\
+	"osfile=/home/user/board.uImage\0"				\
+	"fdtfile=/home/user/board.dtb\0"				\
+	"ubootfile=/home/user/u-boot.bin\0"				\
+	"fdtaddr=c00000\0"						\
+	"osaddr=0x1000000\0"						\
+	"loadaddr=0x1000000\0"						\
+	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
+	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
+	"prog_os1="CONFIG_PROG_OS1"\0"					\
+	"prog_os2="CONFIG_PROG_OS2"\0"					\
+	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
+	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
+	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
+	"bootcmd_flash1=run set_bootargs; "				\
+		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
+	"bootcmd_flash2=run set_bootargs; "				\
+		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
+	"bootcmd=run bootcmd_flash1\0"
+#endif	/* __CONFIG_H */
diff --git a/include/configs/xsengine.h b/include/configs/xsengine.h
deleted file mode 100644
index 9606b53..0000000
--- a/include/configs/xsengine.h
+++ /dev/null
@@ -1,216 +0,0 @@
-/*
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_PXA250			1		/* This is an PXA250 CPU    */
-#define CONFIG_XSENGINE			1
-#define CONFIG_MMC			1
-#define CONFIG_DOS_PARTITION		1
-#define BOARD_LATE_INIT			1
-#undef  CONFIG_USE_IRQ					/* we don't need IRQ/FIQ stuff */
-/* we will never enable dcache, because we have to setup MMU first */
-#define CONFIG_SYS_NO_DCACHE
-
-#define CONFIG_SYS_HZ			1000
-#define CONFIG_SYS_CPUSPEED			0x161           /* set core clock to 400/200/100 MHz */
-
-#define CONFIG_NR_DRAM_BANKS		1		/* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1			0xa0000000	/* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE		0x04000000	/* 64 MB */
-#define PHYS_SDRAM_2			0xa4000000	/* SDRAM Bank #2 */
-#define PHYS_SDRAM_2_SIZE		0x00000000	/* 0 MB */
-#define PHYS_SDRAM_3			0xa8000000	/* SDRAM Bank #3 */
-#define PHYS_SDRAM_3_SIZE		0x00000000	/* 0 MB */
-#define PHYS_SDRAM_4			0xac000000	/* SDRAM Bank #4 */
-#define PHYS_SDRAM_4_SIZE		0x00000000	/* 0 MB */
-#define CONFIG_SYS_DRAM_BASE			0xa0000000
-#define CONFIG_SYS_DRAM_SIZE			0x04000000
-
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define	CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_GBL_DATA_SIZE + PHYS_SDRAM_1)
-
-/* FLASH organization */
-#define CONFIG_SYS_MAX_FLASH_BANKS		1		/* max number of memory banks           */
-#define CONFIG_SYS_MAX_FLASH_SECT		128		/* max number of sectors on one chip    */
-#define PHYS_FLASH_1			0x00000000	/* Flash Bank #1 */
-#define PHYS_FLASH_2			0x00000000	/* Flash Bank #2 */
-#define PHYS_FLASH_SECT_SIZE		0x00020000	/* 127 KB sectors */
-#define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
-
-/*
- * JFFS2 partitions
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00000000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT		"nor0=xsengine-0"
-#define MTDPARTS_DEFAULT	"mtdparts=xsengine-0:256k(uboot),1m(kernel1),8m(kernel2)"
-*/
-
-/* Environment settings */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_ENV_IS_IN_FLASH             1
-#define CONFIG_ENV_ADDR                    (PHYS_FLASH_1 + 0x40000)	/* Addr of Environment Sector (after monitor)*/
-#define CONFIG_ENV_SECT_SIZE               PHYS_FLASH_SECT_SIZE		/* Size of the Environment Sector */
-#define CONFIG_ENV_SIZE                    0x4000				/* 16kB Total Size of Environment Sector */
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT		(75*CONFIG_SYS_HZ)	/* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT		(50*CONFIG_SYS_HZ)	/* Timeout for Flash Write */
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 256*1024)
-#define CONFIG_SYS_GBL_DATA_SIZE		128		/* size in bytes reserved for initial data */
-
-/* Hardware drivers */
-#define CONFIG_NET_MULTI
-#define CONFIG_SMC91111
-#define CONFIG_SMC91111_BASE		0x04000300
-#define CONFIG_SMC_USE_32_BIT		1
-
-/* select serial console configuration */
-#define CONFIG_PXA_SERIAL
-#define CONFIG_FFUART			1
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_BAUDRATE			115200
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_JFFS2
-
-
-#define CONFIG_BOOTDELAY		3
-#define CONFIG_ETHADDR			FF:FF:FF:FF:FF:FF
-#define CONFIG_NETMASK			255.255.255.0
-#define CONFIG_IPADDR			192.168.1.50
-#define CONFIG_SERVERIP			192.168.1.2
-#define CONFIG_BOOTARGS			"root=/dev/mtdblock2 rootfstype=jffs2 console=ttyS1,115200"
-#define CONFIG_CMDLINE_TAG
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_HUSH_PARSER			1
-#define CONFIG_SYS_PROMPT_HUSH_PS2		"> "
-#define CONFIG_SYS_LONGHELP								/* undef to save memory	*/
-#define CONFIG_SYS_PROMPT			"XS-Engine u-boot> "			/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE			256					/* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS			16					/* max number of command args */
-#define CONFIG_SYS_BARGSIZE			CONFIG_SYS_CBSIZE				/* Boot Argument Buffer Size */
-#define CONFIG_SYS_MEMTEST_START		0xA0400000				/* memtest works on     */
-#define CONFIG_SYS_MEMTEST_END			0xA0800000				/* 4 ... 8 MB in DRAM   */
-#define CONFIG_SYS_BAUDRATE_TABLE		{ 9600, 19200, 38400, 57600, 115200 }	/* valid baudrates */
-#define CONFIG_SYS_LOAD_ADDR			0xA0000000				/* load kernel to this address   */
-
-#ifdef CONFIG_MMC
-#define CONFIG_PXA_MMC
-#define CONFIG_CMD_MMC
-#define CONFIG_SYS_MMC_BASE			0xF0000000
-#endif
-
-/* Stack sizes - The stack sizes are set up in start.S using the settings below */
-#define CONFIG_STACKSIZE		(128*1024)	/* regular stack */
-#ifdef  CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
-#endif
-
-/* GP set register */
-#define CONFIG_SYS_GPSR0_VAL			0x0000A000	/* CS1, PROG(FPGA) */
-#define CONFIG_SYS_GPSR1_VAL			0x00020000	/* nPWE */
-#define CONFIG_SYS_GPSR2_VAL			0x0000C000	/* CS2, CS3 */
-
-/* GP clear register */
-#define CONFIG_SYS_GPCR0_VAL			0x00000000
-#define CONFIG_SYS_GPCR1_VAL			0x00000000
-#define CONFIG_SYS_GPCR2_VAL			0x00000000
-
-/* GP direction register */
-#define CONFIG_SYS_GPDR0_VAL			0x0000A000	/* CS1, PROG(FPGA) */
-#define CONFIG_SYS_GPDR1_VAL			0x00022A80	/* nPWE, FFUART + BTUART pins */
-#define CONFIG_SYS_GPDR2_VAL			0x0000C000	/* CS2, CS3 */
-
-/* GP rising edge detect register */
-#define CONFIG_SYS_GRER0_VAL			0x00000000
-#define CONFIG_SYS_GRER1_VAL			0x00000000
-#define CONFIG_SYS_GRER2_VAL			0x00000000
-
-/* GP falling edge detect register */
-#define CONFIG_SYS_GFER0_VAL			0x00000000
-#define CONFIG_SYS_GFER1_VAL			0x00000000
-#define CONFIG_SYS_GFER2_VAL			0x00000000
-
-/* GP alternate function register */
-#define CONFIG_SYS_GAFR0_L_VAL			0x80000000	/* CS1 */
-#define CONFIG_SYS_GAFR0_U_VAL			0x00000010	/* RDY */
-#define CONFIG_SYS_GAFR1_L_VAL			0x09988050	/* FFUART + BTUART pins */
-#define CONFIG_SYS_GAFR1_U_VAL			0x00000008	/* nPWE */
-#define CONFIG_SYS_GAFR2_L_VAL			0xA0000000	/* CS2, CS3 */
-#define CONFIG_SYS_GAFR2_U_VAL			0x00000000
-
-#define CONFIG_SYS_PSSR_VAL			0x00000020	/* Power manager sleep status */
-#define CONFIG_SYS_CCCR_VAL			0x00000161	/* 100 MHz memory, 400 MHz CPU  */
-#define CONFIG_SYS_CKEN_VAL			0x000000C0	/* BTUART and FFUART enabled    */
-#define CONFIG_SYS_ICMR_VAL			0x00000000	/* No interrupts enabled        */
-
-/* Memory settings */
-#define CONFIG_SYS_MSC0_VAL			0x25F425F0
-
-/* MDCNFG: SDRAM Configuration Register */
-#define CONFIG_SYS_MDCNFG_VAL			0x000009C9
-
-/* MDREFR: SDRAM Refresh Control Register */
-#define CONFIG_SYS_MDREFR_VAL			0x00018018
-
-/* MDMRS: Mode Register Set Configuration Register */
-#define CONFIG_SYS_MDMRS_VAL			0x00220022
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/zipitz2.h b/include/configs/zipitz2.h
index ce65d1f..48537e3 100644
--- a/include/configs/zipitz2.h
+++ b/include/configs/zipitz2.h
@@ -27,6 +27,7 @@
  */
 #define	CONFIG_PXA27X		1	/* Marvell PXA270 CPU */
 #define	CONFIG_ZIPITZ2		1	/* Zipit Z2 board */
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 #undef	BOARD_LATE_INIT
 #undef	CONFIG_SKIP_RELOCATE_UBOOT
diff --git a/include/led-display.h b/include/led-display.h
index 41c3744..eaa0f40 100644
--- a/include/led-display.h
+++ b/include/led-display.h
@@ -29,7 +29,6 @@
 /* Display Commands */
 #define DISPLAY_CLEAR	0x1 /* Clear the display */
 #define DISPLAY_HOME	0x2 /* Set cursor at home position */
-#define DISPLAY_MARK	0x4 /* Enable the decimal point led, if implemented */
 
 void display_set(int cmd);
 int display_putc(char c);
diff --git a/include/linux/fb.h b/include/linux/fb.h
new file mode 100644
index 0000000..f4ac4bf
--- /dev/null
+++ b/include/linux/fb.h
@@ -0,0 +1,616 @@
+#ifndef _LINUX_FB_H
+#define _LINUX_FB_H
+
+#include <linux/types.h>
+
+/* Definitions of frame buffers						*/
+
+#define FB_MAX			32	/* sufficient for now */
+
+#define FB_TYPE_PACKED_PIXELS		0	/* Packed Pixels	*/
+
+#define FB_VISUAL_MONO01		0	/* Monochr. 1=Black 0=White */
+#define FB_VISUAL_MONO10		1	/* Monochr. 1=White 0=Black */
+#define FB_VISUAL_TRUECOLOR		2	/* True color	*/
+#define FB_VISUAL_PSEUDOCOLOR		3	/* Pseudo color (like atari) */
+#define FB_VISUAL_DIRECTCOLOR		4	/* Direct color */
+#define FB_VISUAL_STATIC_PSEUDOCOLOR	5	/* Pseudo color readonly */
+
+#define FB_ACCEL_NONE		0	/* no hardware accelerator	*/
+
+struct fb_fix_screeninfo {
+	char id[16];			/* identification string eg "TT Builtin" */
+	unsigned long smem_start;	/* Start of frame buffer mem */
+					/* (physical address) */
+	__u32 smem_len;			/* Length of frame buffer mem */
+	__u32 type;			/* see FB_TYPE_*		*/
+	__u32 type_aux;			/* Interleave for interleaved Planes */
+	__u32 visual;			/* see FB_VISUAL_*		*/
+	__u16 xpanstep;			/* zero if no hardware panning  */
+	__u16 ypanstep;			/* zero if no hardware panning  */
+	__u16 ywrapstep;		/* zero if no hardware ywrap    */
+	__u32 line_length;		/* length of a line in bytes    */
+	unsigned long mmio_start;	/* Start of Memory Mapped I/O   */
+					/* (physical address) */
+	__u32 mmio_len;			/* Length of Memory Mapped I/O  */
+	__u32 accel;			/* Indicate to driver which	*/
+					/*  specific chip/card we have	*/
+	__u16 reserved[3];		/* Reserved for future compatibility */
+};
+
+/*
+ * Interpretation of offset for color fields: All offsets are from the right,
+ * inside a "pixel" value, which is exactly 'bits_per_pixel' wide (means: you
+ * can use the offset as right argument to <<). A pixel afterwards is a bit
+ * stream and is written to video memory as that unmodified.
+ *
+ * For pseudocolor: offset and length should be the same for all color
+ * components. Offset specifies the position of the least significant bit
+ * of the pallette index in a pixel value. Length indicates the number
+ * of available palette entries (i.e. # of entries = 1 << length).
+ */
+struct fb_bitfield {
+	__u32 offset;			/* beginning of bitfield	*/
+	__u32 length;			/* length of bitfield		*/
+	__u32 msb_right;
+
+};
+
+#define FB_NONSTD_HAM		1	/* Hold-And-Modify (HAM)        */
+#define FB_NONSTD_REV_PIX_IN_B	2	/* order of pixels in each byte is reversed */
+
+#define FB_ACTIVATE_NOW		0	/* set values immediately (or vbl)*/
+#define FB_ACTIVATE_NXTOPEN	1	/* activate on next open	*/
+#define FB_ACTIVATE_TEST	2	/* don't set, round up impossible */
+#define FB_ACTIVATE_MASK       15
+					/* values			*/
+#define FB_ACTIVATE_VBL	       16	/* activate values on next vbl  */
+#define FB_CHANGE_CMAP_VBL     32	/* change colormap on vbl	*/
+#define FB_ACTIVATE_ALL	       64	/* change all VCs on this fb	*/
+#define FB_ACTIVATE_FORCE     128	/* force apply even when no change*/
+#define FB_ACTIVATE_INV_MODE  256       /* invalidate videomode */
+
+#define FB_SYNC_HOR_HIGH_ACT	1	/* horizontal sync high active	*/
+#define FB_SYNC_VERT_HIGH_ACT	2	/* vertical sync high active	*/
+#define FB_SYNC_EXT		4	/* external sync		*/
+#define FB_SYNC_COMP_HIGH_ACT	8	/* composite sync high active   */
+#define FB_SYNC_BROADCAST	16	/* broadcast video timings      */
+					/* vtotal = 144d/288n/576i => PAL  */
+					/* vtotal = 121d/242n/484i => NTSC */
+#define FB_SYNC_ON_GREEN	32	/* sync on green */
+
+#define FB_VMODE_NONINTERLACED  0	/* non interlaced */
+#define FB_VMODE_INTERLACED	1	/* interlaced	*/
+#define FB_VMODE_DOUBLE		2	/* double scan */
+#define FB_VMODE_ODD_FLD_FIRST	4	/* interlaced: top line first */
+#define FB_VMODE_MASK		255
+
+#define FB_VMODE_YWRAP		256	/* ywrap instead of panning     */
+#define FB_VMODE_SMOOTH_XPAN	512	/* smooth xpan possible (internally used) */
+#define FB_VMODE_CONUPDATE	512	/* don't update x/yoffset	*/
+
+/*
+ * Display rotation support
+ */
+#define FB_ROTATE_UR      0
+#define FB_ROTATE_CW      1
+#define FB_ROTATE_UD      2
+#define FB_ROTATE_CCW     3
+
+#define PICOS2KHZ(a) (1000000000UL/(a))
+#define KHZ2PICOS(a) (1000000000UL/(a))
+
+struct fb_var_screeninfo {
+	__u32 xres;			/* visible resolution		*/
+	__u32 yres;
+	__u32 xres_virtual;		/* virtual resolution		*/
+	__u32 yres_virtual;
+	__u32 xoffset;			/* offset from virtual to visible */
+	__u32 yoffset;			/* resolution			*/
+
+	__u32 bits_per_pixel;		/* guess what			*/
+	__u32 grayscale;		/* != 0 Graylevels instead of colors */
+
+	struct fb_bitfield red;		/* bitfield in fb mem if true color, */
+	struct fb_bitfield green;	/* else only length is significant */
+	struct fb_bitfield blue;
+	struct fb_bitfield transp;	/* transparency			*/
+
+	__u32 nonstd;			/* != 0 Non standard pixel format */
+
+	__u32 activate;			/* see FB_ACTIVATE_*		*/
+
+	__u32 height;			/* height of picture in mm    */
+	__u32 width;			/* width of picture in mm     */
+
+	__u32 accel_flags;		/* (OBSOLETE) see fb_info.flags */
+
+	/* Timing: All values in pixclocks, except pixclock (of course) */
+	__u32 pixclock;			/* pixel clock in ps (pico seconds) */
+	__u32 left_margin;		/* time from sync to picture	*/
+	__u32 right_margin;		/* time from picture to sync	*/
+	__u32 upper_margin;		/* time from sync to picture	*/
+	__u32 lower_margin;
+	__u32 hsync_len;		/* length of horizontal sync	*/
+	__u32 vsync_len;		/* length of vertical sync	*/
+	__u32 sync;			/* see FB_SYNC_*		*/
+	__u32 vmode;			/* see FB_VMODE_*		*/
+	__u32 rotate;			/* angle we rotate counter clockwise */
+	__u32 reserved[5];		/* Reserved for future compatibility */
+};
+
+struct fb_cmap {
+	__u32 start;			/* First entry	*/
+	__u32 len;			/* Number of entries */
+	__u16 *red;			/* Red values	*/
+	__u16 *green;
+	__u16 *blue;
+	__u16 *transp;			/* transparency, can be NULL */
+};
+
+struct fb_con2fbmap {
+	__u32 console;
+	__u32 framebuffer;
+};
+
+/* VESA Blanking Levels */
+#define VESA_NO_BLANKING        0
+#define VESA_VSYNC_SUSPEND      1
+#define VESA_HSYNC_SUSPEND      2
+#define VESA_POWERDOWN          3
+
+
+enum {
+	/* screen: unblanked, hsync: on,  vsync: on */
+	FB_BLANK_UNBLANK       = VESA_NO_BLANKING,
+
+	/* screen: blanked,   hsync: on,  vsync: on */
+	FB_BLANK_NORMAL        = VESA_NO_BLANKING + 1,
+
+	/* screen: blanked,   hsync: on,  vsync: off */
+	FB_BLANK_VSYNC_SUSPEND = VESA_VSYNC_SUSPEND + 1,
+
+	/* screen: blanked,   hsync: off, vsync: on */
+	FB_BLANK_HSYNC_SUSPEND = VESA_HSYNC_SUSPEND + 1,
+
+	/* screen: blanked,   hsync: off, vsync: off */
+	FB_BLANK_POWERDOWN     = VESA_POWERDOWN + 1
+};
+
+#define FB_VBLANK_VBLANKING	0x001	/* currently in a vertical blank */
+#define FB_VBLANK_HBLANKING	0x002	/* currently in a horizontal blank */
+#define FB_VBLANK_HAVE_VBLANK	0x004	/* vertical blanks can be detected */
+#define FB_VBLANK_HAVE_HBLANK	0x008	/* horizontal blanks can be detected */
+#define FB_VBLANK_HAVE_COUNT	0x010	/* global retrace counter is available */
+#define FB_VBLANK_HAVE_VCOUNT	0x020	/* the vcount field is valid */
+#define FB_VBLANK_HAVE_HCOUNT	0x040	/* the hcount field is valid */
+#define FB_VBLANK_VSYNCING	0x080	/* currently in a vsync */
+#define FB_VBLANK_HAVE_VSYNC	0x100	/* verical syncs can be detected */
+
+struct fb_vblank {
+	__u32 flags;			/* FB_VBLANK flags */
+	__u32 count;			/* counter of retraces since boot */
+	__u32 vcount;			/* current scanline position */
+	__u32 hcount;			/* current scandot position */
+	__u32 reserved[4];		/* reserved for future compatibility */
+};
+
+/* Internal HW accel */
+#define ROP_COPY 0
+#define ROP_XOR  1
+
+struct fb_copyarea {
+	__u32 dx;
+	__u32 dy;
+	__u32 width;
+	__u32 height;
+	__u32 sx;
+	__u32 sy;
+};
+
+struct fb_fillrect {
+	__u32 dx;	/* screen-relative */
+	__u32 dy;
+	__u32 width;
+	__u32 height;
+	__u32 color;
+	__u32 rop;
+};
+
+struct fb_image {
+	__u32 dx;		/* Where to place image */
+	__u32 dy;
+	__u32 width;		/* Size of image */
+	__u32 height;
+	__u32 fg_color;		/* Only used when a mono bitmap */
+	__u32 bg_color;
+	__u8  depth;		/* Depth of the image */
+	const char *data;	/* Pointer to image data */
+	struct fb_cmap cmap;	/* color map info */
+};
+
+/*
+ * hardware cursor control
+ */
+
+#define FB_CUR_SETIMAGE 0x01
+#define FB_CUR_SETPOS   0x02
+#define FB_CUR_SETHOT   0x04
+#define FB_CUR_SETCMAP  0x08
+#define FB_CUR_SETSHAPE 0x10
+#define FB_CUR_SETSIZE	0x20
+#define FB_CUR_SETALL   0xFF
+
+struct fbcurpos {
+	__u16 x, y;
+};
+
+struct fb_cursor {
+	__u16 set;		/* what to set */
+	__u16 enable;		/* cursor on/off */
+	__u16 rop;		/* bitop operation */
+	const char *mask;	/* cursor mask bits */
+	struct fbcurpos hot;	/* cursor hot spot */
+	struct fb_image	image;	/* Cursor image */
+};
+
+#ifdef CONFIG_FB_BACKLIGHT
+/* Settings for the generic backlight code */
+#define FB_BACKLIGHT_LEVELS	128
+#define FB_BACKLIGHT_MAX	0xFF
+#endif
+
+#ifdef __KERNEL__
+
+struct vm_area_struct;
+struct fb_info;
+struct device;
+struct file;
+
+/* Definitions below are used in the parsed monitor specs */
+#define FB_DPMS_ACTIVE_OFF	1
+#define FB_DPMS_SUSPEND		2
+#define FB_DPMS_STANDBY		4
+
+#define FB_DISP_DDI		1
+#define FB_DISP_ANA_700_300	2
+#define FB_DISP_ANA_714_286	4
+#define FB_DISP_ANA_1000_400	8
+#define FB_DISP_ANA_700_000	16
+
+#define FB_DISP_MONO		32
+#define FB_DISP_RGB		64
+#define FB_DISP_MULTI		128
+#define FB_DISP_UNKNOWN		256
+
+#define FB_SIGNAL_NONE		0
+#define FB_SIGNAL_BLANK_BLANK	1
+#define FB_SIGNAL_SEPARATE	2
+#define FB_SIGNAL_COMPOSITE	4
+#define FB_SIGNAL_SYNC_ON_GREEN	8
+#define FB_SIGNAL_SERRATION_ON	16
+
+#define FB_MISC_PRIM_COLOR	1
+#define FB_MISC_1ST_DETAIL	2	/* First Detailed Timing is preferred */
+struct fb_chroma {
+	__u32 redx;	/* in fraction of 1024 */
+	__u32 greenx;
+	__u32 bluex;
+	__u32 whitex;
+	__u32 redy;
+	__u32 greeny;
+	__u32 bluey;
+	__u32 whitey;
+};
+
+struct fb_monspecs {
+	struct fb_chroma chroma;
+	struct fb_videomode *modedb;	/* mode database */
+	__u8  manufacturer[4];		/* Manufacturer */
+	__u8  monitor[14];		/* Monitor String */
+	__u8  serial_no[14];		/* Serial Number */
+	__u8  ascii[14];		/* ? */
+	__u32 modedb_len;		/* mode database length */
+	__u32 model;			/* Monitor Model */
+	__u32 serial;			/* Serial Number - Integer */
+	__u32 year;			/* Year manufactured */
+	__u32 week;			/* Week Manufactured */
+	__u32 hfmin;			/* hfreq lower limit (Hz) */
+	__u32 hfmax;			/* hfreq upper limit (Hz) */
+	__u32 dclkmin;			/* pixelclock lower limit (Hz) */
+	__u32 dclkmax;			/* pixelclock upper limit (Hz) */
+	__u16 input;			/* display type - see FB_DISP_* */
+	__u16 dpms;			/* DPMS support - see FB_DPMS_ */
+	__u16 signal;			/* Signal Type - see FB_SIGNAL_* */
+	__u16 vfmin;			/* vfreq lower limit (Hz) */
+	__u16 vfmax;			/* vfreq upper limit (Hz) */
+	__u16 gamma;			/* Gamma - in fractions of 100 */
+	__u16 gtf	: 1;		/* supports GTF */
+	__u16 misc;			/* Misc flags - see FB_MISC_* */
+	__u8  version;			/* EDID version... */
+	__u8  revision;			/* ...and revision */
+	__u8  max_x;			/* Maximum horizontal size (cm) */
+	__u8  max_y;			/* Maximum vertical size (cm) */
+};
+
+struct fb_cmap_user {
+	__u32 start;			/* First entry	*/
+	__u32 len;			/* Number of entries */
+	__u16 *red;		/* Red values	*/
+	__u16 *green;
+	__u16 *blue;
+	__u16 *transp;		/* transparency, can be NULL */
+};
+
+struct fb_image_user {
+	__u32 dx;			/* Where to place image */
+	__u32 dy;
+	__u32 width;			/* Size of image */
+	__u32 height;
+	__u32 fg_color;			/* Only used when a mono bitmap */
+	__u32 bg_color;
+	__u8  depth;			/* Depth of the image */
+	const char *data;	/* Pointer to image data */
+	struct fb_cmap_user cmap;	/* color map info */
+};
+
+struct fb_cursor_user {
+	__u16 set;			/* what to set */
+	__u16 enable;			/* cursor on/off */
+	__u16 rop;			/* bitop operation */
+	const char *mask;	/* cursor mask bits */
+	struct fbcurpos hot;		/* cursor hot spot */
+	struct fb_image_user image;	/* Cursor image */
+};
+
+/*
+ * Register/unregister for framebuffer events
+ */
+
+/*	The resolution of the passed in fb_info about to change */
+#define FB_EVENT_MODE_CHANGE		0x01
+/*	The display on this fb_info is beeing suspended, no access to the
+ *	framebuffer is allowed any more after that call returns
+ */
+#define FB_EVENT_SUSPEND		0x02
+/*	The display on this fb_info was resumed, you can restore the display
+ *	if you own it
+ */
+#define FB_EVENT_RESUME			0x03
+/*      An entry from the modelist was removed */
+#define FB_EVENT_MODE_DELETE            0x04
+/*      A driver registered itself */
+#define FB_EVENT_FB_REGISTERED          0x05
+/*      A driver unregistered itself */
+#define FB_EVENT_FB_UNREGISTERED        0x06
+/*      CONSOLE-SPECIFIC: get console to framebuffer mapping */
+#define FB_EVENT_GET_CONSOLE_MAP        0x07
+/*      CONSOLE-SPECIFIC: set console to framebuffer mapping */
+#define FB_EVENT_SET_CONSOLE_MAP        0x08
+/*      A hardware display blank change occured */
+#define FB_EVENT_BLANK                  0x09
+/*      Private modelist is to be replaced */
+#define FB_EVENT_NEW_MODELIST           0x0A
+/*	The resolution of the passed in fb_info about to change and
+        all vc's should be changed         */
+#define FB_EVENT_MODE_CHANGE_ALL	0x0B
+/*	A software display blank change occured */
+#define FB_EVENT_CONBLANK               0x0C
+/*      Get drawing requirements        */
+#define FB_EVENT_GET_REQ                0x0D
+/*      Unbind from the console if possible */
+#define FB_EVENT_FB_UNBIND              0x0E
+
+struct fb_event {
+	struct fb_info *info;
+	void *data;
+};
+
+struct fb_blit_caps {
+	u32 x;
+	u32 y;
+	u32 len;
+	u32 flags;
+};
+
+/*
+ * Pixmap structure definition
+ *
+ * The purpose of this structure is to translate data
+ * from the hardware independent format of fbdev to what
+ * format the hardware needs.
+ */
+
+#define FB_PIXMAP_DEFAULT 1     /* used internally by fbcon */
+#define FB_PIXMAP_SYSTEM  2     /* memory is in system RAM  */
+#define FB_PIXMAP_IO      4     /* memory is iomapped       */
+#define FB_PIXMAP_SYNC    256   /* set if GPU can DMA       */
+
+struct fb_pixmap {
+	u8  *addr;		/* pointer to memory			*/
+	u32 size;		/* size of buffer in bytes		*/
+	u32 offset;		/* current offset to buffer		*/
+	u32 buf_align;		/* byte alignment of each bitmap	*/
+	u32 scan_align;		/* alignment per scanline		*/
+	u32 access_align;	/* alignment per read/write (bits)	*/
+	u32 flags;		/* see FB_PIXMAP_*			*/
+	u32 blit_x;             /* supported bit block dimensions (1-32)*/
+	u32 blit_y;             /* Format: blit_x = 1 << (width - 1)    */
+	                        /*         blit_y = 1 << (height - 1)   */
+	                        /* if 0, will be set to 0xffffffff (all)*/
+	/* access methods */
+	void (*writeio)(struct fb_info *info, void *dst, void *src, unsigned int size);
+	void (*readio) (struct fb_info *info, void *dst, void *src, unsigned int size);
+};
+
+#ifdef CONFIG_FB_DEFERRED_IO
+struct fb_deferred_io {
+	/* delay between mkwrite and deferred handler */
+	unsigned long delay;
+	struct mutex lock; /* mutex that protects the page list */
+	struct list_head pagelist; /* list of touched pages */
+	/* callback */
+	void (*deferred_io)(struct fb_info *info, struct list_head *pagelist);
+};
+#endif
+
+/* FBINFO_* = fb_info.flags bit flags */
+#define FBINFO_MODULE		0x0001	/* Low-level driver is a module */
+#define FBINFO_HWACCEL_DISABLED	0x0002
+	/* When FBINFO_HWACCEL_DISABLED is set:
+	 *  Hardware acceleration is turned off.  Software implementations
+	 *  of required functions (copyarea(), fillrect(), and imageblit())
+	 *  takes over; acceleration engine should be in a quiescent state */
+
+/* hints */
+#define FBINFO_PARTIAL_PAN_OK	0x0040 /* otw use pan only for double-buffering */
+#define FBINFO_READS_FAST	0x0080 /* soft-copy faster than rendering */
+
+/*
+ * A driver may set this flag to indicate that it does want a set_par to be
+ * called every time when fbcon_switch is executed. The advantage is that with
+ * this flag set you can really be sure that set_par is always called before
+ * any of the functions dependant on the correct hardware state or altering
+ * that state, even if you are using some broken X releases. The disadvantage
+ * is that it introduces unwanted delays to every console switch if set_par
+ * is slow. It is a good idea to try this flag in the drivers initialization
+ * code whenever there is a bug report related to switching between X and the
+ * framebuffer console.
+ */
+#define FBINFO_MISC_ALWAYS_SETPAR   0x40000
+
+/*
+ * Host and GPU endianness differ.
+ */
+#define FBINFO_FOREIGN_ENDIAN	0x100000
+/*
+ * Big endian math. This is the same flags as above, but with different
+ * meaning, it is set by the fb subsystem depending FOREIGN_ENDIAN flag
+ * and host endianness. Drivers should not use this flag.
+ */
+#define FBINFO_BE_MATH  0x100000
+
+struct fb_info {
+	int node;
+	int flags;
+	struct fb_var_screeninfo var;	/* Current var */
+	struct fb_fix_screeninfo fix;	/* Current fix */
+	struct fb_monspecs monspecs;	/* Current Monitor specs */
+	struct fb_pixmap pixmap;	/* Image hardware mapper */
+	struct fb_pixmap sprite;	/* Cursor hardware mapper */
+	struct fb_cmap cmap;		/* Current cmap */
+	struct list_head modelist;      /* mode list */
+	struct fb_videomode *mode;	/* current mode */
+
+	char *screen_base;	/* Virtual address */
+	unsigned long screen_size;	/* Amount of ioremapped VRAM or 0 */
+	void *pseudo_palette;		/* Fake palette of 16 colors */
+#define FBINFO_STATE_RUNNING	0
+#define FBINFO_STATE_SUSPENDED	1
+	u32 state;			/* Hardware state i.e suspend */
+	void *fbcon_par;                /* fbcon use-only private area */
+	/* From here on everything is device dependent */
+	void *par;
+};
+
+#define FBINFO_DEFAULT	0
+
+#define FBINFO_FLAG_MODULE	FBINFO_MODULE
+#define FBINFO_FLAG_DEFAULT	FBINFO_DEFAULT
+
+// This will go away
+#if defined(__sparc__)
+
+/* We map all of our framebuffers such that big-endian accesses
+ * are what we want, so the following is sufficient.
+ */
+
+// This will go away
+#define fb_readb sbus_readb
+#define fb_readw sbus_readw
+#define fb_readl sbus_readl
+#define fb_readq sbus_readq
+#define fb_writeb sbus_writeb
+#define fb_writew sbus_writew
+#define fb_writel sbus_writel
+#define fb_writeq sbus_writeq
+#define fb_memset sbus_memset_io
+
+#elif defined(__i386__) || defined(__alpha__) || defined(__x86_64__) || defined(__hppa__) || defined(__sh__) || defined(__powerpc__) || defined(__avr32__) || defined(__bfin__)
+
+#define fb_readb __raw_readb
+#define fb_readw __raw_readw
+#define fb_readl __raw_readl
+#define fb_readq __raw_readq
+#define fb_writeb __raw_writeb
+#define fb_writew __raw_writew
+#define fb_writel __raw_writel
+#define fb_writeq __raw_writeq
+#define fb_memset memset_io
+
+#else
+
+#define fb_readb(addr) (*(volatile u8 *) (addr))
+#define fb_readw(addr) (*(volatile u16 *) (addr))
+#define fb_readl(addr) (*(volatile u32 *) (addr))
+#define fb_readq(addr) (*(volatile u64 *) (addr))
+#define fb_writeb(b,addr) (*(volatile u8 *) (addr) = (b))
+#define fb_writew(b,addr) (*(volatile u16 *) (addr) = (b))
+#define fb_writel(b,addr) (*(volatile u32 *) (addr) = (b))
+#define fb_writeq(b,addr) (*(volatile u64 *) (addr) = (b))
+#define fb_memset memset
+
+#endif
+
+#define FB_LEFT_POS(p, bpp)          (fb_be_math(p) ? (32 - (bpp)) : 0)
+#define FB_SHIFT_HIGH(p, val, bits)  (fb_be_math(p) ? (val) >> (bits) : \
+						      (val) << (bits))
+#define FB_SHIFT_LOW(p, val, bits)   (fb_be_math(p) ? (val) << (bits) : \
+						      (val) >> (bits))
+/* drivers/video/fbmon.c */
+#define FB_MAXTIMINGS		0
+#define FB_VSYNCTIMINGS		1
+#define FB_HSYNCTIMINGS		2
+#define FB_DCLKTIMINGS		3
+#define FB_IGNOREMON		0x100
+
+#define FB_MODE_IS_UNKNOWN	0
+#define FB_MODE_IS_DETAILED	1
+#define FB_MODE_IS_STANDARD	2
+#define FB_MODE_IS_VESA		4
+#define FB_MODE_IS_CALCULATED	8
+#define FB_MODE_IS_FIRST	16
+#define FB_MODE_IS_FROM_VAR     32
+
+
+/* drivers/video/fbcmap.c */
+
+extern int fb_alloc_cmap(struct fb_cmap *cmap, int len, int transp);
+extern void fb_dealloc_cmap(struct fb_cmap *cmap);
+extern int fb_copy_cmap(const struct fb_cmap *from, struct fb_cmap *to);
+extern int fb_cmap_to_user(const struct fb_cmap *from, struct fb_cmap_user *to);
+extern int fb_set_cmap(struct fb_cmap *cmap, struct fb_info *fb_info);
+extern int fb_set_user_cmap(struct fb_cmap_user *cmap, struct fb_info *fb_info);
+extern const struct fb_cmap *fb_default_cmap(int len);
+extern void fb_invert_cmaps(void);
+
+struct fb_videomode {
+	const char *name;	/* optional */
+	u32 refresh;		/* optional */
+	u32 xres;
+	u32 yres;
+	u32 pixclock;
+	u32 left_margin;
+	u32 right_margin;
+	u32 upper_margin;
+	u32 lower_margin;
+	u32 hsync_len;
+	u32 vsync_len;
+	u32 sync;
+	u32 vmode;
+	u32 flag;
+};
+
+#endif /* __KERNEL__ */
+
+#endif /* _LINUX_FB_H */
diff --git a/include/post.h b/include/post.h
index daa9047..abe47da 100644
--- a/include/post.h
+++ b/include/post.h
@@ -60,6 +60,10 @@
 #include <asm/immap_85xx.h>
 #define _POST_WORD_ADDR	(CONFIG_SYS_IMMR + offsetof(ccsr_pic_t, tfrr))
 
+#elif defined (CONFIG_MPC86xx)
+#include <asm/immap_86xx.h>
+#define _POST_WORD_ADDR	(CONFIG_SYS_IMMR + offsetof(ccsr_pic_t, tfrr))
+
 #elif defined (CONFIG_4xx)
 #define _POST_WORD_ADDR \
 	(CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
diff --git a/post/drivers/i2c.c b/post/drivers/i2c.c
index b152dea..3080e81 100644
--- a/post/drivers/i2c.c
+++ b/post/drivers/i2c.c
@@ -21,70 +21,89 @@
  * MA 02111-1307 USA
  */
 
-#include <common.h>
-
 /*
  * I2C test
  *
  * For verifying the I2C bus, a full I2C bus scanning is performed.
  *
- * #ifdef I2C_ADDR_LIST
- *   The test is considered as passed if all the devices and
- *   only the devices in the list are found.
- * #else [ ! I2C_ADDR_LIST ]
+ * #ifdef CONFIG_SYS_POST_I2C_ADDRS
+ *   The test is considered as passed if all the devices and only the devices
+ *   in the list are found.
+ *   #ifdef CONFIG_SYS_POST_I2C_IGNORES
+ *     Ignore devices listed in CONFIG_SYS_POST_I2C_IGNORES.  These devices
+ *     are optional or not vital to board functionality.
+ *   #endif
+ * #else [ ! CONFIG_SYS_POST_I2C_ADDRS ]
  *   The test is considered as passed if any I2C device is found.
  * #endif
  */
 
+#include <common.h>
 #include <post.h>
 #include <i2c.h>
 
 #if CONFIG_POST & CONFIG_SYS_POST_I2C
 
+static int i2c_ignore_device(unsigned int chip)
+{
+#ifdef CONFIG_SYS_POST_I2C_IGNORES
+	const unsigned char i2c_ignore_list[] = CONFIG_SYS_POST_I2C_IGNORES;
+	int i;
+
+	for (i = 0; i < sizeof(i2c_ignore_list); i++)
+		if (i2c_ignore_list[i] == chip)
+			return 1;
+#endif
+
+	return 0;
+}
+
 int i2c_post_test (int flags)
 {
 	unsigned int i;
-	unsigned int good = 0;
-#ifdef I2C_ADDR_LIST
-	unsigned int bad  = 0;
+#ifndef CONFIG_SYS_POST_I2C_ADDRS
+	/* Start at address 1, address 0 is the general call address */
+	for (i = 1; i < 128; i++)
+		if (i2c_ignore_device(i))
+			continue;
+		if (i2c_probe (i) == 0)
+			return 0;
+
+	/* No devices found */
+	return -1;
+#else
+	unsigned int ret  = 0;
 	int j;
-	unsigned char i2c_addr_list[] = I2C_ADDR_LIST;
-	unsigned char i2c_miss_list[] = I2C_ADDR_LIST;
-#endif
+	const unsigned char i2c_addr_list[] = CONFIG_SYS_POST_I2C_ADDRS;
 
-	for (i = 0; i < 128; i++) {
-		if (i2c_probe (i) == 0) {
-#ifndef	I2C_ADDR_LIST
-			good++;
-#else	/* I2C_ADDR_LIST */
-			for (j=0; j<sizeof(i2c_addr_list); ++j) {
-				if (i == i2c_addr_list[j]) {
-					good++;
-					i2c_miss_list[j] = 0xFF;
-					break;
-				}
-			}
-			if (j == sizeof(i2c_addr_list)) {
-				bad++;
-				post_log ("I2C: addr %02X not expected\n",
-						i);
+	/* Start at address 1, address 0 is the general call address */
+	for (i = 1; i < 128; i++) {
+		if (i2c_ignore_device(i))
+			continue;
+		if (i2c_probe(i) != 0)
+			continue;
+
+		for (j = 0; j < sizeof(i2c_addr_list); ++j) {
+			if (i == i2c_addr_list[j]) {
+				i2c_addr_list[j] = 0xff;
+				break;
 			}
-#endif	/* I2C_ADDR_LIST */
 		}
-	}
 
-#ifndef	I2C_ADDR_LIST
-	return good > 0 ? 0 : -1;
-#else	/* I2C_ADDR_LIST */
-	if (good != sizeof(i2c_addr_list)) {
-		for (j=0; j<sizeof(i2c_miss_list); ++j) {
-			if (i2c_miss_list[j] != 0xFF) {
-				post_log ("I2C: addr %02X did not respond\n",
-						i2c_miss_list[j]);
-			}
+		if (j == sizeof(i2c_addr_list)) {
+			ret = -1;
+			post_log("I2C: addr %02x not expected\n", i);
 		}
 	}
-	return ((good == sizeof(i2c_addr_list)) && (bad == 0)) ? 0 : -1;
+
+	for (i = 0; i < sizeof(i2c_addr_list); ++i) {
+		if (i2c_addr_list[i] == 0xff)
+			continue;
+		post_log("I2C: addr %02x did not respond\n", i2c_addr_list[i]);
+		ret = -1;
+	}
+
+	return ret;
 #endif
 }