Merge with /home/wd/git/u-boot/master

55 files changed, 3987 insertions, 668 deletions

diff --git a/CHANGELOG b/CHANGELOG
index bc33482..efdf30e 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -16,6 +16,89 @@ Changes since U-Boot 1.1.4:
     by default with the Adder87x U-Boot port.
   Patch by Bryan O'Donoghue <bodonoghue@codehermit.ie>, 29 May 2006
 
+* VoiceBlue update: use new MTD flash partitioning methods, use more
+  reasonable TEXT_BASE, update default environment and enable keyed
+  autoboot.
+  Patch by Ladislav Michl, 16. Aug 2005 
+
+* Add forgotten changes for the PLEB 2 Board.
+  Patch by David Snowdon, 13. Aug 2005
+
+* Add support for wrPPMC7xx/74xx boards
+  Patch by Richard Danter, 12 Aug 2005
+ 
+* Add support for gth2 board
+  Patch by Thomas Lange, Aug 11 2005
+
+* Add support for CONFIG_SERIAL_MULTI on MPC5xxx
+  Patch by Martin Krause, 8 Jun 2006
+
+  This patch supports two serial consoles on boards with
+  a MPC5xxx CPU. The console can be switched at runtime
+  by setting stdin, stdout and stderr to the desired serial
+  interface (serial0 or serial1). The PSCs to be used as
+  console port are definded by CONFIG_PSC_CONSOLE
+  and CONFIG_PSC_CONSOLE2.
+  See README.serial_multi for details.
+
+* Bugfix in I2C initialisation on S3C2400.
+  If the bus is blocked because of a previously interrupted
+  transfer, up to eleven clocks are generated on the I2CSCL
+  line to complete the transfer and to free the bus.
+  With this fix pin I2CSCL (PG6) is really configured as GPIO
+  so the clock pulses are really generated.
+  Patch by Martin Krause, 04 Apr 2006
+  
+* Fix DDR6 errata on TQM834x boards
+  Patch by Thomas Waehner, 07 Mar 2006
+
+* Remove obsolete flash driver board/tqm5200/flash.c
+  Patch by Martin Krause, 11 Jan 2006
+
+* Update configuration for CMC-PU2 board
+  Patch by Martin Krause, 17 Nov 2005
+
+* Add support for PS/2 keyboard on TQM85xx board
+  Patch by Martin Krause, 07 Nov 2005
+
+  Tested on a STK85XX baseboard. Make sure the PS/2 controller
+  has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3
+
+* Fix TRAB channel switching delay for trab_fkt.bin standalone applikation
+  In tsc2000_read_channel() the delay after setting the multiplexer 
+  to a temperature channel is increased from 1,5 ms to 10 ms. This
+  is to allow the multiplexer inputs to stabilize after huge steps
+  of the input signal level.
+  Patch by Martin Krause, 08 Nov 2005
+
+* Adjust TQM5200 make targets
+  Make the automatic CS configuration the default.
+  The dedicated configurations CONFIG_TQM5200_AA, CONFIG_TQM5200_AB
+  and CONFIG_TQM5200_AC are removed.
+  "TQM5200_config" is now the default for STK52XX.200 base boards.
+  On a STK52XX.100 base board "TQM5200_STK100_config" must be used.
+  Patch by Martin Krause, 07 Nov 2005
+
+* Fix setting of environment variable "ver" on trab board
+  The environment variable "ver" is now set before
+  do_auto_update() is called, so that "ver" can be used
+  in USB update scripts.
+  Patch by Martin Krause, 27 Oct 2005
+
+* Fix wrong usage of udelay() in led_blink() on trab board
+  Patch by Martin Krause, 27 Oct 2005
+
+* Fix udelay bug in vfd.c for trab board
+  Patch by Martin Krause, 27 Oct 2005
+
+* Disable JFFS2 support for trab board
+  Patch by Martin Krause, 27 Oct 2005
+
+* Change mtdparts definition on trab board to match current flash map
+  Patch by Martin Krause, 27 Oct 2005
+
+* Fix memory init problems on MCC200 board
+
 * Fix IxEthDB.h to compile again
   Patch by Stefan Roese, 14 Jun 2006
 
diff --git a/CREDITS b/CREDITS
index f91fa3e..94153a7 100644
--- a/CREDITS
+++ b/CREDITS
@@ -105,6 +105,10 @@ N: Magnus Damm
 E: damm@opensource.se
 D: 8xxrom
 
+N: Richard Danter
+E: richard.danter@windriver.com
+D: Support for Wind River PPMC 7xx/74xx boards
+
 N: George G. Davis
 E: gdavis@mvista.com
 D: Board ports for ADS GraphicsClient+ and Intel Assabet
@@ -253,7 +257,7 @@ D  Support for Intrinsyc CERF PXA250 board.
 
 N: Thomas Lange
 E: thomas@corelatus.se
-D: Support for GTH and dbau1x00 boards; lots of PCMCIA fixes
+D: Support for GTH, GTH2 and dbau1x00 boards; lots of PCMCIA fixes
 
 N: Marc Leeman
 E: marc.leeman@barco.com
diff --git a/MAINTAINERS b/MAINTAINERS
index 9a2f472..aaf91cd 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -489,6 +489,7 @@ Wolfgang Denk <wd@denx.de>
 
 Thomas Lange <thomas@corelatus.se>
 	dbau1x00		MIPS32 Au1000
+	gth2			MIPS32 Au1000
 
 #########################################################################
 # Nios-32 Systems:							#
diff --git a/MAKEALL b/MAKEALL
index 6778b3b..804ea12 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -28,7 +28,7 @@ LIST_5xxx="	\
 	BC3450		cpci5200	EVAL5200	icecube_5100	\
 	icecube_5200	lite5200b	mcc200		o2dnt		\
 	pf5200		PM520		Total5100	Total5200	\
-	Total5200_Rev2	TQM5200_auto					\
+	Total5200_Rev2	TQM5200						\
 "
 
 #########################################################################
@@ -142,7 +142,7 @@ LIST_74xx="	\
 "
 
 LIST_7xx="	\
-	BAB7xx		CPCI750		ELPPC				\
+	BAB7xx		CPCI750		ELPPC		ppmc7xx		\
 "
 
 LIST_ppc="${LIST_5xx}  ${LIST_5xxx}		\
@@ -204,9 +204,9 @@ LIST_ARM11="	\
 
 LIST_pxa="	\
 	adsvix		cerf250		cradle		csb226		\
-	delta		innokom		lubbock		pxa255_idp	\
-	wepep250	xaeniax		xm250		xsengine	\
-	zylonite							\
+	delta		innokom		lubbock		pleb2		\
+	pxa255_idp	wepep250	xaeniax		xm250		\
+	xsengine	zylonite					\
 "
 
 LIST_ixp="ixdp425	ixdpg425	pdnb3"
@@ -226,7 +226,7 @@ LIST_mips4kc="incaip"
 
 LIST_mips5kc="purple"
 
-LIST_au1xx0="dbau1000 dbau1100 dbau1500 dbau1550 dbau1550_el"
+LIST_au1xx0="dbau1000 dbau1100 dbau1500 dbau1550 dbau1550_el gth2"
 
 LIST_mips="${LIST_mips4kc} ${LIST_mips5kc} ${LIST_au1xx0}"
 
diff --git a/Makefile b/Makefile
index c8c333b..c2062b0 100644
--- a/Makefile
+++ b/Makefile
@@ -356,8 +356,8 @@ smmaco4_config: unconfig
 	@./mkconfig -a smmaco4 ppc mpc5xxx tqm5200
 
 spieval_config:	unconfig
-	echo "#define CONFIG_CS_AUTOCONF">>include/config.h
-	echo "... with automatic CS configuration"
+	@echo "#define CONFIG_CS_AUTOCONF">>include/config.h
+	@echo "... with automatic CS configuration"
 	@./mkconfig -a spieval ppc mpc5xxx tqm5200
 
 MINI5200_config	\
@@ -394,35 +394,20 @@ Total5200_Rev2_lowboot_config:	unconfig
 		}
 	@./mkconfig -a Total5200 ppc mpc5xxx total5200
 
-TQM5200_auto_config	\
-TQM5200_AA_config	\
-TQM5200_AB_config	\
-TQM5200_AC_config	\
+TQM5200_config	\
+TQM5200_STK100_config \
 MiniFAP_config:	unconfig
 	@ >include/config.h
 	@[ -z "$(findstring MiniFAP,$@)" ] || \
 		{ echo "#define CONFIG_MINIFAP"	>>include/config.h ; \
-		  echo "#define CONFIG_TQM5200_AC"	>>include/config.h ; \
 		  echo "... TQM5200_AC on MiniFAP" ; \
 		}
-	@[ -z "$(findstring AA,$@)" ] || \
-		{ echo "#define CONFIG_TQM5200_AA"	>>include/config.h ; \
-		  echo "... with 4 MB Flash, 16 MB SDRAM, 32 kB EEPROM" ; \
-		}
-	@[ -z "$(findstring AB,$@)" ] || \
-		{ echo "#define CONFIG_TQM5200_AB"	>>include/config.h ; \
-		  echo "... with 64 MB Flash, 64 MB SDRAM, 32 kB EEPROM, 512 kB SRAM" ; \
-		  echo "... with Graphics Controller"; \
-		}
-	@[ -z "$(findstring AC,$@)" ] || \
-		{ echo "#define CONFIG_TQM5200_AC"	>>include/config.h ; \
-		  echo "... with 4 MB Flash, 128 MB SDRAM" ; \
-		  echo "... with Graphics Controller"; \
-		}
-	@[ -z "$(findstring auto,$@)" ] || \
-		{ echo "#define CONFIG_CS_AUTOCONF"	>>include/config.h ; \
-		  echo "... with automatic CS configuration" ; \
+	@[ -z "$(findstring STK100,$@)" ] || \
+		{ echo "#define CONFIG_STK52XX_REV100"	>>include/config.h ; \
+		  echo "... on a STK52XX.100 base board" ; \
 		}
+	@echo "#define CONFIG_CS_AUTOCONF">>include/config.h ;
+	@echo "... with automatic CS configuration" ;
 	@./mkconfig -a TQM5200 ppc mpc5xxx tqm5200
 
 #########################################################################
@@ -1470,6 +1455,9 @@ PCIPPC6_config: unconfig
 ZUMA_config:	unconfig
 	@./mkconfig $(@:_config=) ppc 74xx_7xx evb64260
 
+ppmc7xx_config: unconfig
+	@./mkconfig $(@:_config=) ppc 74xx_7xx ppmc7xx
+	
 #========================================================================
 # ARM
 #========================================================================
@@ -1670,6 +1658,11 @@ cm4008_config	:	unconfig
 cm41xx_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm920t cm41xx NULL ks8695
 
+gth2_config		: 	unconfig
+	@ >include/config.h
+	@echo "#define CONFIG_GTH2 1" >>include/config.h
+	@./mkconfig -a gth2 mips mips gth2
+
 #########################################################################
 ## S3C44B0 Systems
 #########################################################################
@@ -1727,6 +1720,9 @@ ixdpg425_config	:	unconfig
 lubbock_config	:	unconfig
 	@./mkconfig $(@:_config=) arm pxa lubbock
 
+pleb2_config	:	unconfig
+	@./mkconfig $(@:_config=) arm pxa pleb2
+
 logodl_config	:	unconfig
 	@./mkconfig $(@:_config=) arm pxa logodl
 
diff --git a/README b/README
index 178e51e..ad07948 100644
--- a/README
+++ b/README
@@ -310,8 +310,9 @@ The following options need to be configured:
 		CONFIG_IMPA7,	    CONFIG_INNOVATOROMAP1510,	CONFIG_INNOVATOROMAP1610,
 		CONFIG_KB9202,		CONFIG_LART,		CONFIG_LPD7A400,
 		CONFIG_LUBBOCK,		CONFIG_OSK_OMAP5912,	CONFIG_OMAP2420H4,
-		CONFIG_SHANNON,		CONFIG_P2_OMAP730,	CONFIG_SMDK2400,
-		CONFIG_SMDK2410,	CONFIG_TRAB,		CONFIG_VCMA9
+		CONFIG_PLEB2,		CONFIG_SHANNON,		CONFIG_P2_OMAP730,
+		CONFIG_SMDK2400,	CONFIG_SMDK2410,	CONFIG_TRAB,
+		CONFIG_VCMA9
 
 		MicroBlaze based boards:
 		------------------------
diff --git a/board/gth2/Makefile b/board/gth2/Makefile
new file mode 100644
index 0000000..8ef3a51
--- /dev/null
+++ b/board/gth2/Makefile
@@ -0,0 +1,41 @@
+#
+# (C) Copyright 2005
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o ee_access.o
+SOBJS	= lowlevel_init.o
+
+$(LIB):	.depend $(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################
diff --git a/board/gth2/config.mk b/board/gth2/config.mk
new file mode 100644
index 0000000..6d21ba1
--- /dev/null
+++ b/board/gth2/config.mk
@@ -0,0 +1,42 @@
+#
+# (C) Copyright 2004-2005
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+#  AMD Alchemy AU1000, MIPS32 core
+#
+
+ifeq ($(TBASE),0)
+TEXT_BASE = 0
+else
+ifeq ($(TBASE),1)
+TEXT_BASE = 0xbfc10070
+else
+ifeq ($(TBASE),2)
+TEXT_BASE = 0xbfc30070
+else
+## Only to make ordinary make work
+TEXT_BASE = 0x90000000
+endif
+endif
+endif
+
diff --git a/board/gth2/ee_access.c b/board/gth2/ee_access.c
new file mode 100644
index 0000000..e293139
--- /dev/null
+++ b/board/gth2/ee_access.c
@@ -0,0 +1,347 @@
+/* Module for handling DALLAS DS2438, smart battery monitor
+   Chip can store up to 40 bytes of user data in EEPROM,
+   perform temp, voltage and current measurements.
+   Chip also contains a unique serial number.
+
+   Always read/write LSb first
+
+   For documentaion, see data sheet for DS2438, 2438.pdf
+
+   By Thomas.Lange@corelatus.com 001025
+   
+   Copyright (C) 2000-2005 Corelatus AB */
+
+/* This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/au1x00.h>
+#include <asm/io.h>
+#include "ee_dev.h"
+#include "ee_access.h"
+
+/* static int Debug = 1; */
+#undef E_DEBUG
+#define E_DEBUG(fmt,args...) /* */
+/* #define E_DEBUG(fmt,args...) printk("EEA:"fmt,##args); */
+
+/* We dont have kernel functions */
+#define printk printf
+#define KERN_DEBUG
+#define KERN_ERR
+#define EIO 1
+
+#ifndef TRUE
+#define TRUE 1
+#endif
+#ifndef FALSE
+#define FALSE 0
+#endif
+
+/* lookup table ripped from DS app note 17, understanding and using cyclic redundancy checks... */
+
+static u8 crc_lookup[256] = {
+	0,	94,	188,	226,	97,	63,	221,	131,
+	194,	156,	126,	32,	163,	253,	31,	65,
+	157,	195,	33,	127,	252,	162,	64,	30,
+	95,	1,	227,	189,	62,	96,	130,	220,
+	35,	125,	159,	193,	66,	28,	254,	160,
+	225,	191,	93,	3,	128,	222,	60,	98,
+	190,	224,	2,	92,	223,	129,	99,	61,
+	124,	34,	192,	158,	29,	67,	161,	255,
+	70,	24,	250,	164,	39,	121,	155,	197,
+	132,	218,	56,	102,	229,	187,	89,	7,
+	219,	133,	103,	57,	186,	228,	6,	88,
+	25,	71,	165,	251,	120,	38,	196,	154,
+	101,	59,	217,	135,	4,	90,	184,	230,
+	167,	249,	27,	69,	198,	152,	122,	36,
+	248,	166,	68,	26,	153,	199,	37,	123,
+	58,	100,	134,	216,	91,	5,	231,	185,
+	140,	210,	48,	110,	237,	179,	81,	15,
+	78,	16,	242,	172,	47,	113,	147,	205,
+	17,	79,	173,	243,	112,	46,	204,	146,
+	211,	141,	111,	49,	178,	236,	14,	80,
+	175,	241,	19,	77,	206,	144,	114,	44,
+	109,	51,	209,	143,	12,	82,	176,	238,
+	50,	108,	142,	208,	83,	13,	239,	177,
+	240,	174,	76,	18,	145,	207,	45,	115,
+	202,	148,	118,	40,	171,	245,	23,	73,
+	8,	86,	180,	234,	105,	55,	213,	139,
+	87,	9,	235,	181,	54,	104,	138,	212,
+	149,	203,	41,	119,	244,	170,	72,	22,
+	233,	183,	85,	11,	136,	214,	52,	106,
+	43,	117,	151,	201,	74,	20,	246,	168,
+	116,	42,	200,	150,	21,	75,	169,	247,
+	182,	232,	10,	84,	215,	137,	107,	53
+};
+
+static void
+write_gpio_data(int value ){
+	if(value){
+		/* Tristate */
+		gpio_tristate(GPIO_EEDQ);
+	}
+	else{
+		/* Drive 0 */
+		gpio_clear(GPIO_EEDQ);
+	}
+}
+
+static u8 make_new_crc( u8 Old_crc, u8 New_value ){
+	/* Compute a new checksum with new byte, using previous checksum as input
+	   See DS app note 17, understanding and using cyclic redundancy checks...
+	   Also see DS2438, page 11 */
+	return( crc_lookup[Old_crc ^ New_value ]); 
+}
+
+int ee_crc_ok( u8 *Buffer, int Len, u8 Crc ){
+	/* Check if the checksum for this buffer is correct */
+	u8 Curr_crc=0;
+	int i;
+	u8 *Curr_byte = Buffer;
+
+	for(i=0;i<Len;i++){
+		Curr_crc = make_new_crc( Curr_crc, *Curr_byte);
+		Curr_byte++;
+	}
+	E_DEBUG("Calculated CRC = 0x%x, read = 0x%x\n", Curr_crc, Crc);
+  
+	if(Curr_crc == Crc){
+		/* Good */ 
+		return(TRUE);
+	}
+	printk(KERN_ERR"EE checksum error, Calculated CRC = 0x%x, read = 0x%x\n", Curr_crc, Crc);
+	return(FALSE);
+}
+
+static void 
+set_idle(void){
+	/* Send idle and keep start time
+	   Continous 1 is idle */
+	WRITE_PORT(1);
+}
+
+
+static int 
+do_cpu_reset(void){
+	/* Release reset and verify that chip responds with presence pulse */
+	int Retries=0;
+	while(Retries<15){
+		udelay(RESET_LOW_TIME);
+
+		/* Send reset */
+		WRITE_PORT(0);
+		udelay(RESET_LOW_TIME);
+    
+		/* Release reset */
+		WRITE_PORT(1);
+    
+		/* Wait for EEPROM to drive output */
+		udelay(PRESENCE_TIMEOUT);
+		if(!READ_PORT){
+			/* Ok, EEPROM is driving a 0 */
+			E_DEBUG("Presence detected\n");
+			if(Retries){
+				E_DEBUG("Retries %d\n",Retries);
+			}
+			/* Make sure chip releases pin */
+			udelay(PRESENCE_LOW_TIME);
+			return 0;
+		}
+		Retries++;
+	}
+
+	printk(KERN_ERR"eeprom did not respond when releasing reset\n");
+    
+	/* Make sure chip releases pin */
+	udelay(PRESENCE_LOW_TIME);
+
+	/* Set to idle again */
+	set_idle();
+ 
+	return(-EIO);
+}
+
+static u8 
+read_cpu_byte(void){
+	/* Read a single byte from EEPROM
+	   Read LSb first */
+	int i;
+	int Value;
+	u8 Result=0;
+	u32 Flags;
+
+	E_DEBUG("Reading byte\n");
+  
+	for(i=0;i<8;i++){
+		/* Small delay between pulses */
+		udelay(1);
+
+#ifdef __KERNEL__  
+		/* Disable irq */ 
+		save_flags(Flags);
+		cli();
+#endif    
+
+		/* Pull down pin short time to start read
+		   See page 26 in data sheet */
+    
+		WRITE_PORT(0);
+		udelay(READ_LOW);
+		WRITE_PORT(1);
+        
+		/* Wait for chip to drive pin */
+		udelay(READ_TIMEOUT);
+    
+		Value = READ_PORT;
+		if(Value)
+			Value=1;
+
+#ifdef __KERNEL__
+		/* Enable irq */ 
+		restore_flags(Flags);
+#endif
+    
+		/* Wait for chip to release pin */
+		udelay(TOTAL_READ_LOW-READ_TIMEOUT);
+
+		/* LSb first */
+		Result|=Value<<i;
+		/* E_DEBUG("Read %d\n",Value); */
+
+	}
+
+	E_DEBUG("Read byte 0x%x\n",Result);
+
+	return(Result);
+}
+
+static void 
+write_cpu_byte(u8 Byte){
+	/* Write a single byte to EEPROM
+	   Write LSb first */
+	int i;
+	int Value;
+	u32 Flags;
+  
+	E_DEBUG("Writing byte 0x%x\n",Byte);
+  
+	for(i=0;i<8;i++){
+		/* Small delay between pulses */
+		udelay(1);
+		Value = Byte&1;
+    
+#ifdef __KERNEL__
+		/* Disable irq */ 
+		save_flags(Flags);
+		cli();
+#endif    
+
+		/* Pull down pin short time for a 1, long time for a 0
+		   See page 26 in data sheet */
+    
+		WRITE_PORT(0);
+		if(Value){
+			/* Write a 1 */
+			udelay(WRITE_1_LOW);
+		}
+		else{
+			/* Write a 0 */
+			udelay(WRITE_0_LOW);
+		}
+
+		WRITE_PORT(1);
+
+#ifdef __KERNEL__
+		/* Enable irq */ 
+		restore_flags(Flags);
+#endif
+
+		if(Value)
+			/* Wait for chip to read the 1 */
+			udelay(TOTAL_WRITE_LOW-WRITE_1_LOW);
+        
+		/* E_DEBUG("Wrote %d\n",Value); */
+		Byte>>=1;
+	}
+}
+
+int ee_do_cpu_command( u8 *Tx, int Tx_len, u8 *Rx, int Rx_len, int Send_skip ){
+	/* Execute this command string, including 
+	   giving reset and setting to idle after command
+	   if Rx_len is set, we read out data from EEPROM */ 
+	int i;
+
+	E_DEBUG("Command, Tx_len %d, Rx_len %d\n", Tx_len, Rx_len );
+  
+	if(do_cpu_reset()){
+		/* Failed! */
+		return(-EIO);
+	}
+
+	if(Send_skip)
+		/* Always send SKIP_ROM first to tell chip we are sending a command, 
+		   except when we read out rom data for chip */
+		write_cpu_byte(SKIP_ROM);
+  
+	/* Always have Tx data */
+	for(i=0;i<Tx_len;i++){
+		write_cpu_byte(Tx[i]);
+	}
+  
+	if(Rx_len){
+		for(i=0;i<Rx_len;i++){
+			Rx[i]=read_cpu_byte();
+		}
+	}
+  
+	set_idle();
+
+	E_DEBUG("Command done\n");
+
+	return(0);
+} 
+
+int ee_init_cpu_data(void){
+	int i;
+	u8 Tx[10];
+
+	/* Leave it floting since altera is driving the same pin */
+	set_idle();
+
+	/* Copy all User EEPROM data to scratchpad */ 
+	for(i=0;i<USER_PAGES;i++){
+		Tx[0]=RECALL_MEMORY;
+		Tx[1]=EE_USER_PAGE_0+i;
+		if(ee_do_cpu_command(Tx,2,NULL,0,TRUE)) return(-EIO);
+	}
+
+	/* Make sure chip doesnt store measurements in NVRAM */
+	Tx[0]=WRITE_SCRATCHPAD;
+	Tx[1]=0; /* Page */ 
+	Tx[2]=9;
+	if(ee_do_cpu_command(Tx,3,NULL,0,TRUE)) return(-EIO);
+
+	Tx[0]=COPY_SCRATCHPAD;
+	if(ee_do_cpu_command(Tx,2,NULL,0,TRUE)) return(-EIO);
+  
+	for(i=0;i<10;i++){
+		udelay(1000);
+	}
+  
+	return(0);
+}
diff --git a/board/gth2/ee_access.h b/board/gth2/ee_access.h
new file mode 100644
index 0000000..c21730e
--- /dev/null
+++ b/board/gth2/ee_access.h
@@ -0,0 +1,30 @@
+/* By Thomas.Lange@Corelatus.com 001025 */
+
+/* Definitions for EEPROM/VOLT METER  DS2438 */
+/* Copyright (C) 2000-2005 Corelatus AB */
+
+#ifndef INCeeaccessh
+#define INCeeaccessh
+
+#include <asm/types.h>
+#include "ee_dev.h"
+
+int ee_do_cpu_command( u8 *Tx, int Tx_len, u8 *Rx, int Rx_len, int Send_skip );
+int ee_init_cpu_data(void);
+
+int ee_crc_ok( u8 *Buffer, int Len, u8 Crc );
+
+/* Defs for altera reg */
+#define EE_WRITE_SHIFT 8 /* bits to shift left */
+#define EE_READ_SHIFT 16 /* bits to shift left */
+#define EE_DONE  0x80000000
+#define EE_BUSY  0x40000000
+#define EE_ERROR 0x20000000
+
+/* Commands */ 
+#define EE_CMD_NOP      0
+#define EE_CMD_INIT_RES 1
+#define EE_CMD_WR_BYTE  2
+#define EE_CMD_RD_BYTE  3
+
+#endif /* INCeeaccessh */
diff --git a/board/gth2/ee_dev.h b/board/gth2/ee_dev.h
new file mode 100644
index 0000000..acc3418
--- /dev/null
+++ b/board/gth2/ee_dev.h
@@ -0,0 +1,96 @@
+/* By Thomas.Lange@Corelatus.com 001025 */
+/* Definitions for EEPROM/VOLT METER  DS2438 */
+/* Copyright (C) 2000-2005 Corelatus AB */
+
+/* This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef INCeedevh
+#define INCeedevh
+
+#define E_DEBUG(fmt,args...) if( Debug ) printk(KERN_DEBUG"EE: " fmt, ##args) 
+
+/* MIPS */
+#define WRITE_PORT(Value) write_gpio_data(Value)
+
+#define READ_PORT (gpio_read()&GPIO_EEDQ)
+
+/* 64 bytes chip */
+#define EE_CHIP_SIZE 64
+
+/* Board with new current resistor */
+#define EE_GTH_0304 1
+
+/* new dsp and 64 MB SDRAM */
+#define EE_DSP_64 0x10
+
+/* microsecs */
+/* Pull line down at least this long for reset pulse */
+#define RESET_LOW_TIME    490
+
+/* Read presence pulse after we release reset pulse */
+#define PRESENCE_TIMEOUT  100
+#define PRESENCE_LOW_TIME 200
+
+#define WRITE_0_LOW 60
+#define WRITE_1_LOW 1
+#define TOTAL_WRITE_LOW 60
+
+#define READ_LOW        1
+#define READ_TIMEOUT   10
+#define TOTAL_READ_LOW 70
+
+/* Rom function commands */
+#define READ_ROM   0x33
+#define MATCH_ROM  0x55
+#define SKIP_ROM   0xCC
+#define SEARCH_ROM 0xF0
+
+
+/* Memory_command_function */
+#define WRITE_SCRATCHPAD 0x4E
+#define READ_SCRATCHPAD  0xBE
+#define COPY_SCRATCHPAD  0x48
+#define RECALL_MEMORY    0xB8
+#define CONVERT_TEMP     0x44
+#define CONVERT_VOLTAGE  0xB4
+
+/* Chip is divided in 8 pages, 8 bytes each */
+
+#define EE_PAGE_SIZE 8
+
+/* All chip data we want are in page 0 */
+
+/* Bytes in page 0 */
+#define EE_P0_STATUS   0
+#define EE_P0_TEMP_LSB 1
+#define EE_P0_TEMP_MSB 2
+#define EE_P0_VOLT_LSB 3
+#define EE_P0_VOLT_MSB 4
+#define EE_P0_CURRENT_LSB 5
+#define EE_P0_CURRENT_MSB 6
+
+
+/* 40 byte user data is located at page 3-7 */
+#define EE_USER_PAGE_0 3
+#define USER_PAGES 5
+
+/* Layout of gth user pages usage */
+/* Bytes 0-16   ethernet addr in ascii ( len 17 ) */
+
+#define EE_ETHERNET_OFFSET       0
+
+#endif /* INCeedevh */
diff --git a/board/gth2/flash.c b/board/gth2/flash.c
new file mode 100644
index 0000000..f96edff
--- /dev/null
+++ b/board/gth2/flash.c
@@ -0,0 +1,43 @@
+/*
+ * (C) Copyright 2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips */
+
+/*-----------------------------------------------------------------------
+ * flash_init()
+ *
+ * sets up flash_info and returns size of FLASH (bytes)
+ */
+unsigned long flash_init (void)
+{
+	printf ("Skipping flash_init\n");
+	return (0);
+}
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	printf ("write_buff not implemented\n");
+	return (-1);
+}
diff --git a/board/gth2/gth2.c b/board/gth2/gth2.c
new file mode 100644
index 0000000..77fc5b4
--- /dev/null
+++ b/board/gth2/gth2.c
@@ -0,0 +1,435 @@
+/*
+ * (C) Copyright 2005
+ * Thomas.Lange@corelatus.se
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/au1x00.h>
+#include <asm/addrspace.h>
+#include <asm/mipsregs.h>
+#include <watchdog.h>
+
+#include "ee_access.h"
+
+static int wdi_status = 0;
+
+unsigned long mips_io_port_base = 0;
+
+#define SDRAM_SIZE ((64*1024*1024)-(12*4096))
+
+
+#define SERIAL_LOG_BUFFER KSEG1ADDR(SDRAM_SIZE + (8*4096))
+
+void inline log_serial_char(char c){
+	char *serial_log_buffer = (char*)SERIAL_LOG_BUFFER;
+	int serial_log_offset;
+	u32 *serial_log_offsetp = (u32*)SERIAL_LOG_BUFFER;
+
+	serial_log_offset = *serial_log_offsetp;
+
+	*(serial_log_buffer + serial_log_offset) = c;
+
+	serial_log_offset++;
+
+	if(serial_log_offset >= 4096){
+		serial_log_offset = 4;
+	}
+	*serial_log_offsetp = serial_log_offset;
+}
+
+void init_log_serial(void){
+	char *serial_log_buffer = (char*)SERIAL_LOG_BUFFER;
+	u32 *serial_log_offsetp = (u32*)SERIAL_LOG_BUFFER;
+
+	/* Copy buffer from last run */
+	memcpy(serial_log_buffer + 4096, 
+	       serial_log_buffer, 
+	       4096);
+
+	memset(serial_log_buffer, 0, 4096);
+
+	*serial_log_offsetp = 4;	
+}
+
+
+void hw_watchdog_reset(void){
+	volatile u32 *sys_outputset = (volatile u32*)SYS_OUTPUTSET;
+	volatile u32 *sys_outputclear = (volatile u32*)SYS_OUTPUTCLR;
+	if(wdi_status){
+		*sys_outputset = GPIO_CPU_LED|GPIO_WDI;
+		wdi_status = 0;
+	}
+	else{
+		*sys_outputclear = GPIO_CPU_LED|GPIO_WDI;
+		wdi_status = 1;
+	}
+}
+
+long int initdram(int board_type)
+{
+	/* Sdram is setup by assembler code */
+	/* If memory could be changed, we should return the true value here */
+
+	WATCHDOG_RESET();
+
+	return (SDRAM_SIZE);
+}
+
+/* In cpu/mips/cpu.c */
+void write_one_tlb( int index, u32 pagemask, u32 hi, u32 low0, u32 low1 );
+
+void set_ledcard(u32 value){
+	/* Clock 24 bits to led card */
+	int i;
+	volatile u32 *sys_outputset = (volatile u32*)SYS_OUTPUTSET;
+	volatile u32 *sys_outputclr = (volatile u32*)SYS_OUTPUTCLR;
+
+	/* Start with known values */
+	*sys_outputclr = GPIO_LEDCLK|GPIO_LEDD;
+
+	for(i=0;i<24;i++){
+		if(value&0x00800000){
+			*sys_outputset = GPIO_LEDD;
+		}
+		else{
+			*sys_outputclr = GPIO_LEDD;
+		}
+		udelay(1);
+		*sys_outputset = GPIO_LEDCLK;
+		udelay(1);
+		*sys_outputclr = GPIO_LEDCLK;
+		udelay(1);
+		
+		value<<=1;
+	}
+	/* Data is enable output */
+	*sys_outputset = GPIO_LEDD;
+}
+
+int checkboard (void)
+{
+	volatile u32 *sys_counter = (volatile u32*)SYS_COUNTER_CNTRL;
+	volatile u32 *sys_outputset = (volatile u32*)SYS_OUTPUTSET;
+	volatile u32 *sys_outputclr = (volatile u32*)SYS_OUTPUTCLR;
+	u32 proc_id;
+
+	WATCHDOG_RESET();
+
+	*sys_counter = 0x100; /* Enable 32 kHz oscillator for RTC/TOY */
+
+	proc_id = read_32bit_cp0_register(CP0_PRID);
+
+	switch (proc_id >> 24) {
+	case 0:
+		puts ("Board: GTH2\n");
+		printf ("CPU: Au1000 500 MHz, id: 0x%02x, rev: 0x%02x\n",
+			(proc_id >> 8) & 0xFF, proc_id & 0xFF);
+		break;
+	default:
+		printf ("Unsupported cpu %d, proc_id=0x%x\n", proc_id >> 24, proc_id);
+	}
+#ifdef CONFIG_IDE_PCMCIA
+	/* PCMCIA is on a 36 bit physical address.
+	   We need to map it into a 32 bit addresses */
+	write_one_tlb(20,                 /* index */
+		      0x01ffe000,         /* Pagemask, 16 MB pages */
+		      CFG_PCMCIA_IO_BASE, /* Hi */
+		      0x3C000017,         /* Lo0 */
+		      0x3C200017);        /* Lo1 */
+
+	write_one_tlb(21,                   /* index */
+		      0x01ffe000,           /* Pagemask, 16 MB pages */
+		      CFG_PCMCIA_ATTR_BASE, /* Hi */
+		      0x3D000017,           /* Lo0 */
+		      0x3D200017);          /* Lo1 */
+
+	write_one_tlb(22,                   /* index */
+		      0x01ffe000,           /* Pagemask, 16 MB pages */
+		      CFG_PCMCIA_MEM_ADDR,  /* Hi */
+		      0x3E000017,           /* Lo0 */
+		      0x3E200017);          /* Lo1 */
+
+#endif	/* CONFIG_IDE_PCMCIA */
+
+	/* Wait for GPIO ports to become stable */
+	udelay(5000); /* FIXME */
+
+	/* Release reset of ethernet PHY chips */
+	/* Always do this, because linux does not know about it */
+	*sys_outputset = GPIO_ERESET;
+
+	/* Kill FPGA:s */
+	*sys_outputclr = GPIO_CACONFIG|GPIO_DPACONFIG;
+	udelay(2);
+	*sys_outputset = GPIO_CACONFIG|GPIO_DPACONFIG;
+
+	/* Turn front led yellow */
+	set_ledcard(0x00100000);
+
+	return 0;
+}
+
+#define POWER_OFFSET    0xF0000
+#define SW_WATCHDOG_REASON 13
+
+#define BOOTDATA_OFFSET 0xF8000
+#define MAX_ATTEMPTS 5
+
+#define FAILSAFE_BOOT 1
+#define SYSTEM_BOOT   2
+#define SYSTEM2_BOOT  3
+
+#define WRITE_FLASH16(a, d)      \
+do                              \
+{                               \
+  *((volatile u16 *) (a)) = (d);\
+ } while(0)
+
+static void write_bootdata (volatile u16 * addr, u8 System, u8 Count)
+{
+	u16 data;
+	volatile u16 *flash = (u16 *) (CFG_FLASH_BASE);
+
+	switch(System){
+	case FAILSAFE_BOOT:
+		printf ("Setting failsafe boot in flash\n");
+		break;
+	case SYSTEM_BOOT:
+		printf ("Setting system boot in flash\n");
+		break;
+	case SYSTEM2_BOOT:
+		printf ("Setting system2 boot in flash\n");
+		break;
+	default:
+		printf ("Invalid system data %u, setting failsafe\n", System);
+		System = FAILSAFE_BOOT;
+	}
+
+	if ((Count < 1) | (Count > MAX_ATTEMPTS)) {
+		printf ("Invalid boot count %u, setting 1\n", Count);
+		Count = 1;
+	}
+	
+	printf ("Boot attempt %d\n", Count);
+
+	data = (System << 8) | Count;
+	/* AMD 16 bit */
+	WRITE_FLASH16 (&flash[0x555], 0xAAAA);
+	WRITE_FLASH16 (&flash[0x2AA], 0x5555);
+	WRITE_FLASH16 (&flash[0x555], 0xA0A0);
+
+	WRITE_FLASH16 (addr, data);
+}
+
+static int random_system(void){
+	/* EEPROM read failed. Just try to choose one 
+	   system release and hope it works */
+	
+	/* FIXME */
+	return(SYSTEM_BOOT);
+}
+
+static int switch_system(int old_system){
+	u8 Rx[10];
+	u8 Tx[5];
+	int valid_release;
+
+	if(old_system==FAILSAFE_BOOT){
+		/* Find out which system release to use */
+
+		/* Copy from nvram to scratchpad */
+		Tx[0] = RECALL_MEMORY;
+		Tx[1] = 7; /* Page */
+		if (ee_do_cpu_command (Tx, 2, NULL, 0, 1)) {
+			printf ("EE user page 7 recall failed\n");
+			return (random_system());
+		}
+
+		Tx[0] = READ_SCRATCHPAD;
+		if (ee_do_cpu_command (Tx, 2, Rx, 9, 1)) {
+			printf ("EE user page 7 read failed\n");
+			return (random_system());
+		}
+		/* Crc in 9:th byte */
+		if (!ee_crc_ok (Rx, 8, *(Rx + 8))) {
+			printf ("EE read failed, page 7. CRC error\n");
+			return (random_system());
+		}
+
+		valid_release = Rx[7];
+		if((valid_release==0xFF)|
+		   ((valid_release&1) == 0)){
+			return(SYSTEM_BOOT);
+		}
+		else{
+			return(SYSTEM2_BOOT);
+		}
+	}
+	else{
+		return(FAILSAFE_BOOT);
+	}
+}
+
+static void check_boot_tries (void)
+{
+	/* Count the number of boot attemps
+	   switch system if too many */
+
+	int i;
+	volatile u16 *addr;
+	volatile u16 data;
+	u8 system = FAILSAFE_BOOT;
+	u8 count;
+
+	addr = (u16 *) (CFG_FLASH_BASE + BOOTDATA_OFFSET);
+
+	if (*addr == 0xFFFF) {
+		printf ("*** No bootdata exists. ***\n");
+		write_bootdata (addr, FAILSAFE_BOOT, 1);
+	} else {
+		/* Search for latest written bootdata */
+		i = 0;
+		while ((*(addr + 1) != 0xFFFF) & (i < 8000)) {
+			addr++;
+			i++;
+		}
+		if (i >= 8000) {
+			/* Whoa, dont write any more */
+			printf ("*** No bootdata found. Not updating flash***\n");
+		} else {
+			/* See how many times we have tried to boot real system */
+			data = *addr;
+			system = data >> 8;
+			count = data & 0xFF;
+			if ((system != SYSTEM_BOOT) & 
+			    (system != SYSTEM2_BOOT) & 
+			    (system != FAILSAFE_BOOT)) {
+				printf ("*** Wrong system %d\n", system);
+				system = FAILSAFE_BOOT;
+				count = 1;
+			} else {
+				switch (count) {
+				case 0:
+				case 1:
+				case 2:
+				case 3:
+				case 4:
+					/* Try same system again if needed */
+					count++;
+					break;
+
+				case 5:
+					/* Switch system and reset tries */
+					count = 1;
+					system = switch_system(system);
+					printf ("***Too many boot attempts, switching system***\n");
+					break;
+				default:
+					/* Switch system, start over and hope it works */
+					printf ("***Unexpected data on addr 0x%x, %u***\n",
+						(u32) addr, data);
+					count = 1;
+					system = switch_system(system);
+				}
+			}
+			write_bootdata (addr + 1, system, count);
+		}
+	}
+	switch(system){
+	case FAILSAFE_BOOT:
+		printf ("Booting failsafe system\n");
+		setenv ("bootargs", "panic=1 root=/dev/hda7");
+		setenv ("bootcmd", "ide reset;disk 0x81000000 0:5;run addmisc;bootm");
+		break;
+
+	case SYSTEM_BOOT:
+		printf ("Using normal system\n");
+		setenv ("bootargs", "panic=1 root=/dev/hda4");
+		setenv ("bootcmd", "ide reset;disk 0x81000000 0:2;run addmisc;bootm");
+		break;
+
+	case SYSTEM2_BOOT:
+		printf ("Using normal system2\n");
+		setenv ("bootargs", "panic=1 root=/dev/hda9");
+		setenv ("bootcmd", "ide reset;disk 0x81000000 0:8;run addmisc;bootm");
+		break;
+	default:
+		printf ("Invalid system %d\n", system);
+		printf ("Hanging\n");
+		while(1);
+	}
+}
+
+int misc_init_r(void){
+	u8 Rx[80];
+	u8 Tx[5];
+	int page;
+	int read = 0;
+
+	WATCHDOG_RESET();
+
+	if (ee_init_cpu_data ()) {
+		printf ("EEPROM init failed\n");
+		return (0);
+	}
+
+	/* Check which release to boot */
+	check_boot_tries ();
+
+	/* Read the pages where ethernet address is stored */
+
+	for (page = EE_USER_PAGE_0; page <= EE_USER_PAGE_0 + 2; page++) {
+		/* Copy from nvram to scratchpad */
+		Tx[0] = RECALL_MEMORY;
+		Tx[1] = page;
+		if (ee_do_cpu_command (Tx, 2, NULL, 0, 1)) {
+			printf ("EE user page %d recall failed\n", page);
+			return (0);
+		}
+
+		Tx[0] = READ_SCRATCHPAD;
+		if (ee_do_cpu_command (Tx, 2, Rx + read, 9, 1)) {
+			printf ("EE user page %d read failed\n", page);
+			return (0);
+		}
+		/* Crc in 9:th byte */
+		if (!ee_crc_ok (Rx + read, 8, *(Rx + read + 8))) {
+			printf ("EE read failed, page %d. CRC error\n", page);
+			return (0);
+		}
+		read += 8;
+	}
+
+	/* Add eos after eth addr */
+	Rx[17] = 0;
+
+	printf ("Ethernet addr read from eeprom: %s\n\n", Rx);
+
+	if ((Rx[2] != ':') |
+	    (Rx[5] != ':') |
+	    (Rx[8] != ':') | (Rx[11] != ':') | (Rx[14] != ':')) {
+		printf ("*** ethernet addr invalid, using default ***\n");
+	} else {
+		setenv ("ethaddr", Rx);
+	}
+	return (0);
+}
diff --git a/board/gth2/lowlevel_init.S b/board/gth2/lowlevel_init.S
new file mode 100644
index 0000000..62e3657
--- /dev/null
+++ b/board/gth2/lowlevel_init.S
@@ -0,0 +1,454 @@
+/* Memory sub-system initialization code */
+
+#include <config.h>
+#include <version.h>
+#include <asm/regdef.h>
+#include <asm/au1x00.h>
+#include <asm/mipsregs.h>
+
+#define CP0_Config0		$16
+#define MEM_1MS			((CFG_MHZ) * 1000)
+#define GPIO_RJ1LY     (1<<22)
+#define GPIO_CFRESET   (1<<10)
+
+	.text
+	.set noreorder
+	.set mips32
+
+	.globl	lowlevel_init
+lowlevel_init:
+	/*
+	 * Step 2) Establish Status Register
+	 * (set BEV, clear ERL, clear EXL, clear IE)
+	 */
+	li	t1, 0x00400000
+	mtc0	t1, CP0_STATUS
+
+	/*
+	 * Step 3) Establish CP0 Config0
+	 * (set OD, set K0=3)
+	 */
+	li	t1, 0x00080003
+	mtc0	t1, CP0_CONFIG
+
+	/*
+	 * Step 4) Disable Watchpoint facilities
+	 */
+	li t1, 0x00000000
+	mtc0	t1, CP0_WATCHLO
+	mtc0	t1, CP0_IWATCHLO
+	/*
+	 * Step 5) Disable the performance counters
+	 */
+	mtc0	zero, CP0_PERFORMANCE
+	nop
+
+	/*
+	 * Step 6) Establish EJTAG Debug register
+	 */
+	mtc0	zero, CP0_DEBUG
+	nop
+
+	/*
+	 * Step 7) Establish Cause
+	 * (set IV bit)
+	 */
+	li	t1, 0x00800000
+	mtc0	t1, CP0_CAUSE
+
+	/* Establish Wired (and Random) */
+	mtc0	zero, CP0_WIRED
+	nop
+
+	/* No workaround if running from ram */
+	lui	t0, 0xffc0
+	lui	t3, 0xbfc0
+	and	t1, ra, t0
+	bne	t1, t3, noCacheJump
+	nop
+
+	/*** From AMD YAMON ***/
+	/*
+	 * Step 8) Initialize the caches
+	 */
+	li		t0, (16*1024)
+	li		t1, 32
+	li		t2, 0x80000000
+	addu	t3, t0, t2
+cacheloop:
+	cache	0, 0(t2)
+	cache	1, 0(t2)
+	addu	t2, t1
+	bne		t2, t3, cacheloop
+	nop
+
+	/* Save return address */
+	move		t3, ra
+
+	/* Run from cacheable space now */
+	bal		cachehere
+	nop
+cachehere:
+	li		t1, ~0x20000000 /* convert to KSEG0 */
+	and		t0, ra, t1
+	addi	t0, 5*4			/* 5 insns beyond cachehere */
+	jr		t0
+	nop
+
+	/* Restore return address */
+	move		ra, t3
+
+	/*
+	 * Step 9) Initialize the TLB
+	 */
+	li		t0, 0			# index value
+	li		t1, 0x00000000		# entryhi value
+	li		t2, 32			# 32 entries
+
+tlbloop:
+	/* Probe TLB for matching EntryHi */
+	mtc0	t1, CP0_ENTRYHI
+	tlbp
+	nop
+
+	/* Examine Index[P], 1=no matching entry */
+	mfc0	t3, CP0_INDEX
+	li	t4, 0x80000000
+	and	t3, t4, t3
+	addiu	t1, t1, 1		# increment t1 (asid)
+	beq	zero, t3, tlbloop
+	nop
+
+	/* Initialize the TLB entry */
+	mtc0	t0, CP0_INDEX
+	mtc0	zero, CP0_ENTRYLO0
+	mtc0	zero, CP0_ENTRYLO1
+	mtc0	zero, CP0_PAGEMASK
+	tlbwi
+
+	/* Do it again */
+	addiu	t0, t0, 1
+	bne	t0, t2, tlbloop
+	nop
+
+	/* First setup pll:s to make serial work ok */
+	/* We have a 12.5 MHz crystal */
+	li	t0, SYS_CPUPLL
+	li	t1, 0x28  /* CPU clock, 500 MHz */
+	sw	t1, 0(t0)
+	sync
+	nop
+	nop
+
+	/* wait 1mS for clocks to settle */
+	li	t1, MEM_1MS
+1:	add	t1, -1
+	bne	t1, zero, 1b
+	nop
+	/* Setup AUX PLL */
+	li	t0, SYS_AUXPLL
+	li	t1, 0
+	sw	t1, 0(t0) /* aux pll */
+	sync
+
+	/*  Static memory controller */
+	/* RCE0 - can not change while fetching, do so from icache */
+	move		t2, ra /* Store return address */
+	bal		getAddr
+	nop
+
+getAddr:
+	move		t1, ra
+	move		ra, t2 /* Move return addess back */
+
+	cache	0x14,0(t1)
+	cache	0x14,32(t1)
+	/*** /From YAMON ***/
+
+noCacheJump:
+
+	/*  Static memory controller */
+
+	/* RCE0 AMD 29LV800 Flash */
+	li	t0, MEM_STCFG0
+	li	t1, 0x00000243
+	sw	t1, 0(t0)
+
+	li	t0, MEM_STTIME0
+	li	t1, 0x040181D7 /* FIXME */
+	sw	t1, 0(t0)
+
+	li	t0, MEM_STADDR0
+	li	t1, 0x11E03F80
+	sw	t1, 0(t0)
+
+	/* RCE1 PCMCIA 250ns */
+	li	t0, MEM_STCFG1
+	li	t1, 0x00000002
+	sw	t1, 0(t0)
+
+	li	t0, MEM_STTIME1
+	li	t1, 0x280E3E07
+	sw	t1, 0(t0)
+
+	li	t0, MEM_STADDR1
+	li	t1, 0x10000000
+	sw	t1, 0(t0)
+
+	/* RCE2 CP Altera */
+	li	t0, MEM_STCFG2
+	li	t1, 0x00000280 /* BE, EW */ 
+	sw	t1, 0(t0)
+
+	li	t0, MEM_STTIME2
+	li	t1, 0x0303000c 
+	sw	t1, 0(t0)
+
+	li	t0, MEM_STADDR2
+	li	t1, 0x10c03f80 /* 1 MB */
+	sw	t1, 0(t0)
+
+	/* RCE3 DP Altera */
+	li	t0, MEM_STCFG3
+	li	t1, 0x00000280 /* BE, EW */ 
+	sw	t1, 0(t0)
+
+	li	t0, MEM_STTIME3
+	li	t1, 0x0303000c 
+	sw	t1, 0(t0)
+
+	li	t0, MEM_STADDR3
+	li	t1, 0x10e03f80 /* 1 MB */
+	sw	t1, 0(t0)
+
+	sync
+
+	/* Set peripherals to a known state */
+	li	t0, IC0_CFG0CLR
+	li	t1, 0xFFFFFFFF
+	sw	t1, 0(t0)
+
+	li	t0, IC0_CFG0CLR
+	sw	t1, 0(t0)
+
+	li	t0, IC0_CFG1CLR
+	sw	t1, 0(t0)
+
+	li	t0, IC0_CFG2CLR
+	sw	t1, 0(t0)
+
+	li	t0, IC0_SRCSET
+	sw	t1, 0(t0)
+
+	li	t0, IC0_ASSIGNSET
+	sw	t1, 0(t0)
+
+	li	t0, IC0_WAKECLR
+	sw	t1, 0(t0)
+
+	li	t0, IC0_RISINGCLR
+	sw	t1, 0(t0)
+
+	li	t0, IC0_FALLINGCLR
+	sw	t1, 0(t0)
+
+	li	t0, IC0_TESTBIT
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+	sync
+
+	li	t0, IC1_CFG0CLR
+	li	t1, 0xFFFFFFFF
+	sw	t1, 0(t0)
+
+	li	t0, IC1_CFG0CLR
+	sw	t1, 0(t0)
+
+	li	t0, IC1_CFG1CLR
+	sw	t1, 0(t0)
+
+	li	t0, IC1_CFG2CLR
+	sw	t1, 0(t0)
+
+	li	t0, IC1_SRCSET
+	sw	t1, 0(t0)
+
+	li	t0, IC1_ASSIGNSET
+	sw	t1, 0(t0)
+
+	li	t0, IC1_WAKECLR
+	sw	t1, 0(t0)
+
+	li	t0, IC1_RISINGCLR
+	sw	t1, 0(t0)
+
+	li	t0, IC1_FALLINGCLR
+	sw	t1, 0(t0)
+
+	li	t0, IC1_TESTBIT
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+	sync
+
+	li	t0, SYS_FREQCTRL0
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+	li	t0, SYS_FREQCTRL1
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+	li	t0, SYS_CLKSRC
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+	li	t0, SYS_PININPUTEN
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+	sync
+
+	li	t0, 0xB1100100
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+	li	t0, 0xB1400100
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+
+	li	t0, SYS_WAKEMSK
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+	li	t0, SYS_WAKESRC
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+	/* wait 1mS before setup */
+	li	t1, MEM_1MS
+1:	add	t1, -1
+	bne	t1, zero, 1b
+	nop
+
+
+/* SDCS 0 SDRAM */
+	li	t0, MEM_SDMODE0
+	li	t1, 0x592CD1
+	sw	t1, 0(t0)
+
+	li	t0, MEM_SDMODE1
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+	li	t0, MEM_SDMODE2
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+/* 64 MB SDRAM at addr 0 */
+	li	t0, MEM_SDADDR0
+	li	t1, 0x001003F0
+	sw	t1, 0(t0)
+
+
+	li	t0, MEM_SDADDR1
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+	li	t0, MEM_SDADDR2
+	li	t1, 0x00000000
+	sw	t1, 0(t0)
+
+	sync
+
+	li	t0, MEM_SDREFCFG
+	li	t1, 0x880007A1 /* Disable */
+	sw	t1, 0(t0)
+	sync
+
+	li	t0, MEM_SDPRECMD
+	sw	zero, 0(t0)
+	sync
+
+	li	t0, MEM_SDAUTOREF
+	sw	zero, 0(t0)
+	sync
+	sw	zero, 0(t0)
+	sync
+
+	li	t0, MEM_SDREFCFG
+	li	t1, 0x8A0007A1 /* Enable */
+	sw	t1, 0(t0)
+	sync
+
+	li	t0, MEM_SDWRMD0
+	li	t1, 0x00000023
+	sw	t1, 0(t0)
+	sync
+
+	/* wait 1mS after setup */
+	li	t1, MEM_1MS
+1:	add	t1, -1
+	bne	t1, zero, 1b
+	nop
+
+	/* Setup GPIO pins */
+
+	li	t0, SYS_PINFUNC
+	li	t1, 0x00007025 /* 0x8080 */
+	sw	t1, 0(t0)
+
+	li	t0, SYS_TRIOUTCLR
+	li	t1, 0xFFFFFFFF /* 0x1FFF */
+	sw	t1, 0(t0)
+
+	/* Turn yellow front led on */
+	/* Release reset on CF */
+	li	t0, SYS_OUTPUTCLR
+	li	t1, GPIO_RJ1LG
+	sw	t1, 0(t0)
+	li	t0, SYS_OUTPUTSET
+	li	t1, GPIO_RJ1LY|GPIO_CFRESET
+	sw	t1, 0(t0)
+	sync
+	j clearmem
+	nop
+
+	.globl	memtest
+memtest:
+	/* Fill memory with address */
+	li	t0, 0x80000000
+	li	t1, 0xFFF000 /* 64 MB */
+mt0:	sw	t0, 0(t0)
+	add	t1, -1
+	add	t0, 4
+	bne	t1, zero, mt0
+	nop
+	nop
+	/* Verify addr */
+	li	t0, 0x80000000
+	li	t1, 0xFFF000 /* 64 MB */
+mt1:	lw	t2, 0(t0)
+	bne	t0, t2, memhang	
+	add	t1, -1
+	add	t0, 4
+	bne	t1, zero, mt1
+	nop
+	nop
+	.globl	clearmem
+clearmem:		
+		/* Clear memory */
+	li	t0, 0x80000000
+	li	t1, 0xFFF000 /* 64 MB */
+mtc:	sw	zero, 0(t0)
+	add	t1, -1
+	add	t0, 4
+	bne	t1, zero, mtc
+	nop
+	nop
+memtestend:		
+	j	ra
+	nop
+	
+memhang:	
+	b	memhang
+	nop
diff --git a/board/gth2/u-boot.lds b/board/gth2/u-boot.lds
new file mode 100644
index 0000000..8ba0b6d
--- /dev/null
+++ b/board/gth2/u-boot.lds
@@ -0,0 +1,68 @@
+/*
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk Engineering, <wd@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+OUTPUT_FORMAT("elf32-bigmips", "elf32-bigmips", "elf32-bigmips")
+*/
+OUTPUT_FORMAT("elf32-tradbigmips", "elf32-tradbigmips", "elf32-tradbigmips")
+OUTPUT_ARCH(mips)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text       :
+	{
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata  : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data  : { *(.data) }
+
+	. = ALIGN(4);
+	.sdata  : { *(.sdata) }
+
+	_gp = ALIGN(16);
+
+	__got_start = .;
+	.got  : { *(.got) }
+	__got_end = .;
+
+	.sdata  : { *(.sdata) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	uboot_end_data = .;
+	num_got_entries = (__got_end - __got_start) >> 2;
+
+	. = ALIGN(4);
+	.sbss  : { *(.sbss) }
+	.bss  : { *(.bss) }
+	uboot_end = .;
+}
diff --git a/board/mcc200/mcc200.c b/board/mcc200/mcc200.c
index 87427e4..b9b9a71 100644
--- a/board/mcc200/mcc200.c
+++ b/board/mcc200/mcc200.c
@@ -28,7 +28,11 @@
 #include <mpc5xxx.h>
 #include <pci.h>
 
-#include "mt48lc8m32b2-6-7.h"
+/* Two MT48LC8M32B2 for 32 MB */
+/* #include "mt48lc8m32b2-6-7.h" */
+
+/* One MT48LC16M32S2 for 64 MB */
+#include "mt48lc16m32s2-75.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -74,6 +78,8 @@ static void sdram_start (int hi_addr)
 	/* normal operation */
 	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
 	__asm__ volatile ("sync");
+
+	udelay(10);
 }
 #endif
 
diff --git a/board/mcc200/mt48lc16m32s2-75.h b/board/mcc200/mt48lc16m32s2-75.h
new file mode 100644
index 0000000..ffdf039
--- /dev/null
+++ b/board/mcc200/mt48lc16m32s2-75.h
@@ -0,0 +1,43 @@
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR	0		/* is SDR */
+
+#if defined(CONFIG_MPC5200)
+/* Settings for XLB = 132 MHz */
+#define SDRAM_MODE	0x00CD0000
+#define SDRAM_CONTROL	0x504F0000
+#define SDRAM_CONFIG1	0xD2322800
+#define SDRAM_CONFIG2	0x8AD70000
+
+#elif defined(CONFIG_MGT5100)
+/* Settings for XLB = 66 MHz */
+#define SDRAM_MODE	0x008D0000
+#define SDRAM_CONTROL	0x504F0000
+#define SDRAM_CONFIG1	0xC2222600
+#define SDRAM_CONFIG2	0x88B70004
+#define SDRAM_ADDRSEL	0x02000000
+
+#else
+#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined
+#endif
diff --git a/board/ppmc7xx/Makefile b/board/ppmc7xx/Makefile
new file mode 100644
index 0000000..c378677
--- /dev/null
+++ b/board/ppmc7xx/Makefile
@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= ppmc7xx.o pci.o flash.o
+SOBJS	:= init.o
+
+$(LIB):	.depend $(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
diff --git a/board/ppmc7xx/config.mk b/board/ppmc7xx/config.mk
new file mode 100644
index 0000000..bcb6c81
--- /dev/null
+++ b/board/ppmc7xx/config.mk
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2005
+# Richard Danter, Wind River Systems 
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# 
+#
+
+TEXT_BASE = 0xFFF00000
+TEXT_END  = 0xFFF40000
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE)
diff --git a/board/ppmc7xx/flash.c b/board/ppmc7xx/flash.c
new file mode 100644
index 0000000..1cbcadc
--- /dev/null
+++ b/board/ppmc7xx/flash.c
@@ -0,0 +1,494 @@
+/*
+ * flash.c
+ * -------
+ * 
+ * Flash programming routines for the Wind River PPMC 74xx/7xx
+ * based on flash.c from the TQM8260 board.
+ * 
+ * By Richard Danter (richard.danter@windriver.com)
+ * Copyright (C) 2005 Wind River Systems
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <74xx_7xx.h>
+
+#define DWORD unsigned long long
+
+/* Local function prototypes */
+static int	write_dword (flash_info_t* info, ulong dest, unsigned char *pdata);
+static void	write_via_fpu (volatile DWORD* addr, DWORD* data);
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+/*-----------------------------------------------------------------------
+ */
+void flash_reset (void)
+{
+	unsigned long msr;
+	DWORD cmd_reset = 0x00F000F000F000F0LL;
+	
+	if (flash_info[0].flash_id != FLASH_UNKNOWN) {
+		msr = get_msr ();
+		set_msr (msr | MSR_FP);
+
+		write_via_fpu ((DWORD*)flash_info[0].start[0], &cmd_reset );
+		
+		set_msr (msr);
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+ulong flash_get_size (ulong baseaddr, flash_info_t * info)
+{
+	int i;
+	unsigned long msr;
+	DWORD flashtest;
+	DWORD cmd_select[3] = { 0x00AA00AA00AA00AALL, 0x0055005500550055LL,
+							0x0090009000900090LL };
+
+	/* Enable FPU */
+	msr = get_msr ();
+	set_msr (msr | MSR_FP);	
+							
+	/* Write auto-select command sequence */
+	write_via_fpu ((DWORD*)(baseaddr + (0x0555 << 3)), &cmd_select[0] );
+	write_via_fpu ((DWORD*)(baseaddr + (0x02AA << 3)), &cmd_select[1] );
+	write_via_fpu ((DWORD*)(baseaddr + (0x0555 << 3)), &cmd_select[2] );
+	
+	/* Restore FPU */
+	set_msr (msr);
+	
+	/* Read manufacturer ID */
+	flashtest = *(volatile DWORD*)baseaddr;
+	switch ((int)flashtest) {
+	case AMD_MANUFACT:
+		info->flash_id = FLASH_MAN_AMD;
+		break;
+	case FUJ_MANUFACT:
+		info->flash_id = FLASH_MAN_FUJ;
+		break;
+	default:
+		/* No, faulty or unknown flash */ 
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		return (0);
+	}
+
+	/* Read device ID */
+	flashtest = *(volatile DWORD*)(baseaddr + 8);
+	switch ((long)flashtest) {
+	case AMD_ID_LV800T:
+		info->flash_id += FLASH_AM800T;
+		info->sector_count = 19;
+		info->size = 0x00400000;
+		break;
+	case AMD_ID_LV800B:
+		info->flash_id += FLASH_AM800B;
+		info->sector_count = 19;
+		info->size = 0x00400000;
+		break;
+	case AMD_ID_LV160T:
+		info->flash_id += FLASH_AM160T;
+		info->sector_count = 35;
+		info->size = 0x00800000;
+		break;
+	case AMD_ID_LV160B:
+		info->flash_id += FLASH_AM160B;
+		info->sector_count = 35;
+		info->size = 0x00800000;
+		break;
+	case AMD_ID_DL322T:
+		info->flash_id += FLASH_AMDL322T;
+		info->sector_count = 71;
+		info->size = 0x01000000;
+		break;
+	case AMD_ID_DL322B:
+		info->flash_id += FLASH_AMDL322B;
+		info->sector_count = 71;
+		info->size = 0x01000000;
+		break;
+	case AMD_ID_DL323T:
+		info->flash_id += FLASH_AMDL323T;
+		info->sector_count = 71;
+		info->size = 0x01000000;
+		break;
+	case AMD_ID_DL323B:
+		info->flash_id += FLASH_AMDL323B;
+		info->sector_count = 71;
+		info->size = 0x01000000;
+		break;
+	case AMD_ID_LV640U:
+		info->flash_id += FLASH_AM640U;
+		info->sector_count = 128;
+		info->size = 0x02000000;
+		break;
+	default:
+		/* Unknown flash type */
+		info->flash_id = FLASH_UNKNOWN;
+		return (0);
+	}
+
+	if ((long)flashtest == AMD_ID_LV640U) {
+		/* set up sector start adress table (uniform sector type) */
+		for (i = 0; i < info->sector_count; i++)
+			info->start[i] = baseaddr + (i * 0x00040000);
+	} else if (info->flash_id & FLASH_BTYPE) {
+		/* set up sector start adress table (bottom sector type) */
+		info->start[0] = baseaddr + 0x00000000;
+		info->start[1] = baseaddr + 0x00010000;
+		info->start[2] = baseaddr + 0x00018000;
+		info->start[3] = baseaddr + 0x00020000;
+		for (i = 4; i < info->sector_count; i++) {
+			info->start[i] = baseaddr + (i * 0x00040000) - 0x000C0000;
+		}
+	} else {
+		/* set up sector start adress table (top sector type) */
+		i = info->sector_count - 1;
+		info->start[i--] = baseaddr + info->size - 0x00010000;
+		info->start[i--] = baseaddr + info->size - 0x00018000;
+		info->start[i--] = baseaddr + info->size - 0x00020000;
+		for (; i >= 0; i--) {
+			info->start[i] = baseaddr + i * 0x00040000;
+		}
+	}
+
+	/* check for protected sectors */
+	for (i = 0; i < info->sector_count; i++) {
+		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
+		if (*(volatile DWORD*)(info->start[i] + 16) & 0x0001000100010001LL) {
+			info->protect[i] = 1;	/* D0 = 1 if protected */
+		} else {
+			info->protect[i] = 0;
+		}
+	}
+
+	flash_reset ();
+	return (info->size);
+}
+
+/*-----------------------------------------------------------------------
+ */
+unsigned long flash_init (void)
+{
+	unsigned long size_b0 = 0;
+	int i;
+
+	/* Init: no FLASHes known */
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	/* Static FLASH Bank configuration here (only one bank) */
+	size_b0 = flash_get_size (CFG_FLASH_BASE, &flash_info[0]);
+	if (flash_info[0].flash_id == FLASH_UNKNOWN || size_b0 == 0) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+				size_b0, size_b0 >> 20);
+	}
+
+	/*
+	 * protect monitor and environment sectors
+	 */
+#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_MONITOR_BASE,
+		       CFG_MONITOR_BASE + monitor_flash_len - 1, &flash_info[0]);
+#endif
+
+#if (CFG_ENV_IS_IN_FLASH == 1) && defined(CFG_ENV_ADDR)
+# ifndef  CFG_ENV_SIZE
+#  define CFG_ENV_SIZE	CFG_ENV_SECT_SIZE
+# endif
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_ENV_ADDR,
+		       CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+#endif
+
+	return (size_b0);
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_AMD:
+		printf ("AMD ");
+		break;
+	case FLASH_MAN_FUJ:
+		printf ("FUJITSU ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_AM800T:
+		printf ("29LV800T (8 M, top sector)\n");
+		break;
+	case FLASH_AM800B:
+		printf ("29LV800T (8 M, bottom sector)\n");
+		break;
+	case FLASH_AM160T:
+		printf ("29LV160T (16 M, top sector)\n");
+		break;
+	case FLASH_AM160B:
+		printf ("29LV160B (16 M, bottom sector)\n");
+		break;
+	case FLASH_AMDL322T:
+		printf ("29DL322T (32 M, top sector)\n");
+		break;
+	case FLASH_AMDL322B:
+		printf ("29DL322B (32 M, bottom sector)\n");
+		break;
+	case FLASH_AMDL323T:
+		printf ("29DL323T (32 M, top sector)\n");
+		break;
+	case FLASH_AMDL323B:
+		printf ("29DL323B (32 M, bottom sector)\n");
+		break;
+	case FLASH_AM640U:
+		printf ("29LV640D (64 M, uniform sector)\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+			info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i],
+			info->protect[i] ? " (RO)" : "     "
+		);
+	}
+	printf ("\n");
+	return;
+}
+
+/*-----------------------------------------------------------------------
+ */
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	int flag, prot, sect, l_sect;
+	ulong start, now, last;
+	unsigned long msr;
+	DWORD cmd_erase[6] = { 0x00AA00AA00AA00AALL, 0x0055005500550055LL,
+						   0x0080008000800080LL, 0x00AA00AA00AA00AALL,
+						   0x0055005500550055LL, 0x0030003000300030LL };
+	
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect])
+			prot++;
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+	l_sect = -1;
+
+	/* Enable FPU */
+	msr = get_msr();
+	set_msr ( msr | MSR_FP );
+						   
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	write_via_fpu ((DWORD*)(info->start[0] + (0x0555 << 3)), &cmd_erase[0] );
+	write_via_fpu ((DWORD*)(info->start[0] + (0x02AA << 3)), &cmd_erase[1] );
+	write_via_fpu ((DWORD*)(info->start[0] + (0x0555 << 3)), &cmd_erase[2] );
+	write_via_fpu ((DWORD*)(info->start[0] + (0x0555 << 3)), &cmd_erase[3] );
+	write_via_fpu ((DWORD*)(info->start[0] + (0x02AA << 3)), &cmd_erase[4] );
+	udelay (1000);
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			write_via_fpu ((DWORD*)info->start[sect], &cmd_erase[5] );
+			l_sect = sect;
+		}
+	}
+
+	/* re-enable interrupts if necessary */
+	if (flag)
+		enable_interrupts ();
+
+	/* Restore FPU */
+	set_msr (msr);
+	
+	/* wait at least 80us - let's wait 1 ms */
+	udelay (1000);
+
+	/*
+	 * We wait for the last triggered sector
+	 */
+	if (l_sect < 0)
+		goto DONE;
+
+	start = get_timer (0);
+	last = start;
+	while ((*(volatile DWORD*)info->start[l_sect] & 0x0080008000800080LL )
+				!= 0x0080008000800080LL )
+	{
+		if ((now = get_timer (start)) > CFG_FLASH_ERASE_TOUT) {
+			printf ("Timeout\n");
+			return 1;
+		}
+		/* show that we're waiting */
+		if ((now - last) > 1000) {	/* every second */
+			serial_putc ('.');
+			last = now;
+		}
+	}
+
+  DONE:
+	/* reset to read mode */
+	flash_reset ();
+	
+	printf (" done\n");
+	return 0;
+}
+
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong dp;
+	static unsigned char bb[8];
+	int i, l, rc, cc = cnt;
+
+	dp = (addr & ~7);		/* get lower dword aligned address */
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - dp) != 0) {
+		for (i = 0; i < 8; i++)
+			bb[i] = (i < l || (i - l) >= cc) ? *(char*)(dp + i) : *src++;
+		if ((rc = write_dword (info, dp, bb)) != 0) {
+			return (rc);
+		}
+		dp += 8;
+		cc -= 8 - l;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	while (cc >= 8) {
+		if ((rc = write_dword (info, dp, src)) != 0) {
+			return (rc);
+		}
+		dp += 8;
+		src += 8;
+		cc -= 8;
+	}
+
+	if (cc <= 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	for (i = 0; i < 8; i++) {
+		bb[i] = (i < cc) ? *src++ : *(char*)(dp + i);
+	}
+	return (write_dword (info, dp, bb));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a dword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_dword (flash_info_t * info, ulong dest, unsigned char *pdata)
+{
+	ulong start;
+	unsigned long msr;
+	int flag, i;
+	DWORD data;
+	DWORD cmd_write[3] = { 0x00AA00AA00AA00AALL, 0x0055005500550055LL,
+						   0x00A000A000A000A0LL };
+						   
+	for (data = 0, i = 0; i < 8; i++)
+		data = (data << 8) + *pdata++;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*(DWORD*)dest & data) != data) {
+		return (2);
+	}
+	
+	/* Enable FPU */
+	msr = get_msr();
+	set_msr( msr | MSR_FP );
+	
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	write_via_fpu ((DWORD*)(info->start[0] + (0x0555 << 3)), &cmd_write[0] );
+	write_via_fpu ((DWORD*)(info->start[0] + (0x02AA << 3)), &cmd_write[1] );
+	write_via_fpu ((DWORD*)(info->start[0] + (0x0555 << 3)), &cmd_write[2] );
+	write_via_fpu ((DWORD*)dest, &data );
+
+	/* re-enable interrupts if necessary */
+	if (flag)
+		enable_interrupts ();
+
+	/* Restore FPU */
+	set_msr(msr);
+	
+	/* data polling for D7 */
+	start = get_timer (0);
+	while (*(volatile DWORD*)dest != data ) {
+		if (get_timer (start) > CFG_FLASH_WRITE_TOUT) {
+			return (1);
+		}
+	}
+	return (0);
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void write_via_fpu (volatile DWORD* addr, DWORD* data)
+{
+	__asm__ __volatile__ ("lfd  1, 0(%0)"::"r" (data));
+	__asm__ __volatile__ ("stfd 1, 0(%0)"::"r" (addr));
+	__asm__ __volatile__ ("eieio");
+}
diff --git a/board/ppmc7xx/init.S b/board/ppmc7xx/init.S
new file mode 100644
index 0000000..e4ed7a6
--- /dev/null
+++ b/board/ppmc7xx/init.S
@@ -0,0 +1,336 @@
+/*
+ * init.S
+ * ------
+ *
+ * Wind River PPMC 7xx/74xx init code.
+ *
+ * By Richard Danter (richard.danter@windriver.com)
+ * Copyright (C) 2005 Wind River Systems
+ *
+ * NOTE: The following code was generated automatically by Workbench
+ *       from the ppmc7400_107.reg register file.
+ */
+
+#include <ppc_asm.tmpl>
+
+
+.globl board_asm_init
+board_asm_init:
+
+      lis    r4,0xFEC0
+      ori    r4,r4,0x0000
+      lis    r5,0xFEE0
+      ori    r5,r5,0x0000
+      lis    r3,0x8000          # ADDR_00                        
+      ori    r3,r3,0x0000
+      stwbrx    r3,0,r4
+      li     r3,0x1057          # VENDOR                         
+      li    r8, 0x0
+      sthbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_02                        
+      ori    r3,r3,0x0002
+      stwbrx    r3,0,r4
+      li     r3,0x0004          # ID                             
+      li    r8, 0x2
+      sthbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_04                        
+      ori    r3,r3,0x0004
+      stwbrx    r3,0,r4
+      li     r3,0x0006          # PCICMD                         
+      li    r8, 0x0
+      sthbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_06                        
+      ori    r3,r3,0x0006
+      stwbrx    r3,0,r4
+      li     r3,0x00A0          # PCISTAT                        
+      li    r8, 0x2
+      sthbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_08                        
+      ori    r3,r3,0x0008
+      stwbrx    r3,0,r4
+      li     r3,0x10            # REVID                          
+      stb    r3,0x0(r5)
+      lis    r3,0x8000          # ADDR_09                        
+      ori    r3,r3,0x0009
+      stwbrx    r3,0,r4
+      li     r3,0x00            # PROGIR                         
+      stb    r3,0x1(r5)
+      lis    r3,0x8000          # ADDR_0A                        
+      ori    r3,r3,0x000A
+      stwbrx    r3,0,r4
+      li     r3,0x00            # SUBCCODE                       
+      stb    r3,0x2(r5)
+      lis    r3,0x8000          # ADDR_0B                        
+      ori    r3,r3,0x000B
+      stwbrx    r3,0,r4
+      li     r3,0x06            # PBCCR                          
+      stb    r3,0x3(r5)
+      lis    r3,0x8000          # ADDR_0C                        
+      ori    r3,r3,0x000C
+      stwbrx    r3,0,r4
+      li     r3,0x08            # PCLSR                          
+      stb    r3,0x0(r5)
+      lis    r3,0x8000          # ADDR_0D                        
+      ori    r3,r3,0x000D
+      stwbrx    r3,0,r4
+      li     r3,0x00            # PLTR                           
+      stb    r3,0x1(r5)
+      lis    r3,0x8000          # ADDR_0E                        
+      ori    r3,r3,0x000E
+      stwbrx    r3,0,r4
+      li     r3,0x00            # HEADTYPE                       
+      stb    r3,0x2(r5)
+      lis    r3,0x8000          # ADDR_0F                        
+      ori    r3,r3,0x000F
+      stwbrx    r3,0,r4
+      li     r3,0x00            # BISTCTRL                       
+      stb    r3,0x3(r5)
+      lis    r3,0x8000          # ADDR_10                        
+      ori    r3,r3,0x0010
+      stwbrx    r3,0,r4
+      lis    r3,0x0000          # LMBAR                          
+      ori    r3,r3,0x0008
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_14                        
+      ori    r3,r3,0x0014
+      stwbrx    r3,0,r4
+      lis    r3,0xF000          # PCSRBAR                        
+      ori    r3,r3,0x0000
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_3C                        
+      ori    r3,r3,0x003C
+      stwbrx    r3,0,r4
+      li     r3,0x00            # ILR                            
+      stb    r3,0x0(r5)
+      lis    r3,0x8000          # ADDR_3D                        
+      ori    r3,r3,0x003D
+      stwbrx    r3,0,r4
+      li     r3,0x01            # INTPIN                         
+      stb    r3,0x1(r5)
+      lis    r3,0x8000          # ADDR_3E                        
+      ori    r3,r3,0x003E
+      stwbrx    r3,0,r4
+      li     r3,0x00            # MIN_GNT                        
+      stb    r3,0x2(r5)
+      lis    r3,0x8000          # ADDR_3F                        
+      ori    r3,r3,0x003F
+      stwbrx    r3,0,r4
+      li     r3,0x00            # MAX_LAT                        
+      stb    r3,0x3(r5)
+      lis    r3,0x8000          # ADDR_40                        
+      ori    r3,r3,0x0040
+      stwbrx    r3,0,r4
+      li     r3,0x00            # BUSNB                          
+      stb    r3,0x0(r5)
+      lis    r3,0x8000          # ADDR_41                        
+      ori    r3,r3,0x0041
+      stwbrx    r3,0,r4
+      li     r3,0x00            # SBUSNB                         
+      stb    r3,0x1(r5)
+      lis    r3,0x8000          # ADDR_46                        
+      ori    r3,r3,0x0046
+      stwbrx    r3,0,r4
+#      li     r3,0xE080          # PCIARB                         
+      li     r3,-0x1F80          # PCIARB                         
+      li    r8, 0x2
+      sthbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_70                        
+      ori    r3,r3,0x0070
+      stwbrx    r3,0,r4
+      li     r3,0x0000          # PMCR1                          
+      li    r8, 0x0
+      sthbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_72                        
+      ori    r3,r3,0x0072
+      stwbrx    r3,0,r4
+      li     r3,0xC0            # PMCR2                          
+      stb    r3,0x2(r5)
+      lis    r3,0x8000          # ADDR_73                        
+      ori    r3,r3,0x0073
+      stwbrx    r3,0,r4
+      li     r3,0xEF            # ODCR                           
+      stb    r3,0x3(r5)
+      lis    r3,0x8000          # ADDR_74                        
+      ori    r3,r3,0x0074
+      stwbrx    r3,0,r4
+      li     r3,0x7D00          # CLKDCR                         
+      li    r8, 0x0
+      sthbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_76                        
+      ori    r3,r3,0x0076
+      stwbrx    r3,0,r4
+      li     r3,0x00            # MDCR                           
+      stb    r3,0x2(r5)
+      lis    r6,0xFCE0
+      ori    r6,r6,0x0000       # r6 is the EUMBAR Base Address
+      lis    r3,0x8000          # ADDR_78                        
+      ori    r3,r3,0x0078
+      stwbrx    r3,0,r4
+      lis    r3,0xFCE0          # EUMBBAR                        
+      ori    r3,r3,0x0000
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_80                        
+      ori    r3,r3,0x0080
+      stwbrx    r3,0,r4
+      lis    r3,0xFFFF          # MSADDR1                        
+      ori    r3,r3,0x4000
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_84                        
+      ori    r3,r3,0x0084
+      stwbrx    r3,0,r4
+      lis    r3,0xFFFF          # MSADDR2                        
+      ori    r3,r3,0xFFFF
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_88                        
+      ori    r3,r3,0x0088
+      stwbrx    r3,0,r4
+      lis    r3,0x0303          # EMSADDR1                       
+      ori    r3,r3,0x0000
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_8C                        
+      ori    r3,r3,0x008C
+      stwbrx    r3,0,r4
+      lis    r3,0x0303          # EMSADDR2                       
+      ori    r3,r3,0x0303
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_90                        
+      ori    r3,r3,0x0090
+      stwbrx    r3,0,r4
+      lis    r3,0xFFFF          # EMEADDR1                       
+      ori    r3,r3,0x7F3F
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_94                        
+      ori    r3,r3,0x0094
+      stwbrx    r3,0,r4
+      lis    r3,0xFFFF          # EMEADDR2                       
+      ori    r3,r3,0xFFFF
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_98                        
+      ori    r3,r3,0x0098
+      stwbrx    r3,0,r4
+      lis    r3,0x0303          # EXTEMEM1                       
+      ori    r3,r3,0x0000
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_9C                        
+      ori    r3,r3,0x009C
+      stwbrx    r3,0,r4
+      lis    r3,0x0303          # EXTEMEM2                       
+      ori    r3,r3,0x0303
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_A0                        
+      ori    r3,r3,0x00A0
+      stwbrx    r3,0,r4
+      li     r3,0x03            # MEMBNKEN                       
+      stb    r3,0x0(r5)
+      lis    r3,0x8000          # ADDR_A3                        
+      ori    r3,r3,0x00A3
+      stwbrx    r3,0,r4
+      li     r3,0x00            # MEMPMODE                       
+      stb    r3,0x3(r5)
+      lis    r3,0x8000          # ADDR_B8                        
+      ori    r3,r3,0x00B8
+      stwbrx    r3,0,r4
+      li     r3,0x00            # ECCCNT                         
+      stb    r3,0x0(r5)
+      lis    r3,0x8000          # ADDR_B9                        
+      ori    r3,r3,0x00B9
+      stwbrx    r3,0,r4
+      li     r3,0x00            # ECCTRG                         
+      stb    r3,0x1(r5)
+      lis    r3,0x8000          # ADDR_C0                        
+      ori    r3,r3,0x00C0
+      stwbrx    r3,0,r4
+      li     r3,0xFF            # ERRENR1                        
+      stb    r3,0x0(r5)
+      lis    r3,0x8000          # ADDR_C1                        
+      ori    r3,r3,0x00C1
+      stwbrx    r3,0,r4
+      li     r3,0x00            # ERRDR1                         
+      stb    r3,0x1(r5)
+      lis    r3,0x8000          # ADDR_C3                        
+      ori    r3,r3,0x00C3
+      stwbrx    r3,0,r4
+      li     r3,0x50            # IPBESR                         
+      stb    r3,0x3(r5)
+      lis    r3,0x8000          # ADDR_C4                        
+      ori    r3,r3,0x00C4
+      stwbrx    r3,0,r4
+      li     r3,0xBF            # ERRENR2                        
+      stb    r3,0x0(r5)
+      lis    r3,0x8000          # ADDR_C5                        
+      ori    r3,r3,0x00C5
+      stwbrx    r3,0,r4
+      li     r3,0x00            # ERRDR2                         
+      stb    r3,0x1(r5)
+      lis    r3,0x8000          # ADDR_C7                        
+      ori    r3,r3,0x00C7
+      stwbrx    r3,0,r4
+      li     r3,0x00            # PCIBESR                        
+      stb    r3,0x3(r5)
+      lis    r3,0x8000          # ADDR_C8                        
+      ori    r3,r3,0x00C8
+      stwbrx    r3,0,r4
+      lis    r3,0x0000          # BERRADDR                       
+      ori    r3,r3,0xE0FE
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_E0                        
+      ori    r3,r3,0x00E0
+      stwbrx    r3,0,r4
+      li     r3,0xC0            # AMBOR                          
+      stb    r3,0x0(r5)
+      lis    r3,0x8000          # ADDR_F4                        
+      ori    r3,r3,0x00F4
+      stwbrx    r3,0,r4
+      lis    r3,0x0000          # MCCR2                          
+      ori    r3,r3,0x020C
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_F8                        
+      ori    r3,r3,0x00F8
+      stwbrx    r3,0,r4
+      lis    r3,0x0230          # MCCR3                          
+      ori    r3,r3,0x0000
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_FC                        
+      ori    r3,r3,0x00FC
+      stwbrx    r3,0,r4
+      lis    r3,0x2532          # MCCR4                          
+      ori    r3,r3,0x2220
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_F0                        
+      ori    r3,r3,0x00F0
+      stwbrx    r3,0,r4
+      lis    r3,0xFFC8          # MCCR1                          
+      ori    r3,r3,0x0000
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_A8                        
+      ori    r3,r3,0x00A8
+      stwbrx    r3,0,r4
+      lis    r3,0xFF14          # PICR1                          
+      ori    r3,r3,0x1CC8
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+      lis    r3,0x8000          # ADDR_AC                        
+      ori    r3,r3,0x00AC
+      stwbrx    r3,0,r4
+      lis    r3,0x0000          # PICR2                          
+      ori    r3,r3,0x0000
+      li    r8, 0x0
+      stwbrx    r3,r8,r5
+
+      blr
diff --git a/board/ppmc7xx/pci.c b/board/ppmc7xx/pci.c
new file mode 100644
index 0000000..5b115ea
--- /dev/null
+++ b/board/ppmc7xx/pci.c
@@ -0,0 +1,97 @@
+/*
+ * (C) Copyright 2002 ELTEC Elektronik AG
+ * Frank Gottschling <fgottschling@eltec.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * PCI initialisation for the MPC10x.
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <mpc106.h>
+
+#ifdef CONFIG_PCI
+
+struct pci_controller local_hose;
+
+void pci_init_board(void)
+{
+    struct pci_controller* hose = (struct pci_controller *)&local_hose;
+    u16 reg16;
+
+    hose->first_busno = 0;
+    hose->last_busno = 0xff;
+
+    pci_set_region(hose->regions + 0,
+	CFG_PCI_MEMORY_BUS,
+	CFG_PCI_MEMORY_PHYS,
+	CFG_PCI_MEMORY_SIZE,
+	PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+    /* PCI memory space */
+    pci_set_region(hose->regions + 1,
+	CFG_PCI_MEM_BUS,
+	CFG_PCI_MEM_PHYS,
+	CFG_PCI_MEM_SIZE,
+	PCI_REGION_MEM);
+
+    /* ISA/PCI memory space */
+    pci_set_region(hose->regions + 2,
+	CFG_ISA_MEM_BUS,
+	CFG_ISA_MEM_PHYS,
+	CFG_ISA_MEM_SIZE,
+	PCI_REGION_MEM);
+
+    /* PCI I/O space */
+    pci_set_region(hose->regions + 3,
+	CFG_PCI_IO_BUS,
+	CFG_PCI_IO_PHYS,
+	CFG_PCI_IO_SIZE,
+	PCI_REGION_IO);
+
+    /* ISA/PCI I/O space */
+    pci_set_region(hose->regions + 4,
+	CFG_ISA_IO_BUS,
+	CFG_ISA_IO_PHYS,
+	CFG_ISA_IO_SIZE,
+	PCI_REGION_IO);
+
+    hose->region_count = 5;
+
+    pci_setup_indirect(hose,
+	MPC106_REG_ADDR,
+	MPC106_REG_DATA);
+
+    pci_register_hose(hose);
+
+    hose->last_busno = pci_hose_scan(hose);
+
+    /* Initialises the MPC10x PCI Configuration regs. */
+    pci_read_config_word (PCI_BDF(0,0,0), PCI_COMMAND, &reg16);
+    reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+    pci_write_config_word(PCI_BDF(0,0,0), PCI_COMMAND, reg16);
+
+    /* Clear non-reserved bits in status register */
+    pci_write_config_word(PCI_BDF(0,0,0), PCI_STATUS, 0xffff);
+}
+
+#endif /* CONFIG_PCI */
diff --git a/board/ppmc7xx/ppmc7xx.c b/board/ppmc7xx/ppmc7xx.c
new file mode 100644
index 0000000..0597c72
--- /dev/null
+++ b/board/ppmc7xx/ppmc7xx.c
@@ -0,0 +1,104 @@
+/*
+ * ppmc7xx.c
+ * ---------
+ * 
+ * Main board-specific routines for Wind River PPMC 7xx/74xx board.
+ * 
+ * By Richard Danter (richard.danter@windriver.com)
+ * Copyright (C) 2005 Wind River Systems
+ */
+
+#include <common.h>
+#include <command.h>
+
+
+/* Define some MPC107 (memory controller) registers */
+#define MPC107_EUMB_GCR         0xfce41020
+#define MPC107_EUMB_IACKR       0xfce600a0
+
+
+/* Function prototypes */
+extern void unlock_ram_in_cache( void );
+extern void _start_warm(void);
+
+
+/*
+ * initdram()
+ * 
+ * This function normally initialises the (S)DRAM of the system. For this board
+ * the SDRAM was already initialised by board_asm_init (see init.S) so we just
+ * return the size of RAM.
+ */
+long initdram( int board_type )
+{
+    return CFG_SDRAM_SIZE;
+}
+
+
+/*
+ * after_reloc()
+ * 
+ * This is called after U-Boot has been copied from Flash/ROM to RAM. It gives
+ * us an opportunity to do some additional setup before the rest of the system
+ * is initialised. We don't need to do anything, so we just call board_init_r()
+ * which should never return.
+ */ 
+void after_reloc( ulong dest_addr, gd_t* gd )
+{
+	/* Jump to the main U-Boot board init code */
+	board_init_r( gd, dest_addr );
+}
+
+
+/*
+ * checkboard()
+ * 
+ * We could do some board level checks here, such as working out what version
+ * it is, but for this board we simply display it's name (on the console).
+ */
+int checkboard( void )
+{
+    puts( "Board: Wind River PPMC 7xx/74xx\n" );
+    return 0;
+}
+
+
+/*
+ * misc_init_r
+ * 
+ * Used for other setup which needs to be done late in the bring-up phase.
+ */
+int misc_init_r( void )
+{
+	/* Reset the EPIC and clear pending interrupts */
+	out32r(MPC107_EUMB_GCR, 0xa0000000);
+	while( in32r( MPC107_EUMB_GCR ) & 0x80000000 );
+	out32r( MPC107_EUMB_GCR, 0x20000000 );
+	while( in32r( MPC107_EUMB_IACKR ) != 0xff );
+
+	/* Enable the I-Cache */
+	icache_enable();
+	
+	return 0;
+}
+
+
+/*
+ * do_reset()
+ * 
+ * Shell command to reset the board.
+ */
+void do_reset( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[] )
+{
+	printf( "Resetting...\n" );
+	
+	/* Disabe and invalidate cache */
+	icache_disable();
+	dcache_disable();
+
+	/* Jump to warm start (in RAM) */
+	_start_warm();
+	
+	/* Should never get here */
+	while(1);
+}
diff --git a/board/ppmc7xx/u-boot.lds b/board/ppmc7xx/u-boot.lds
new file mode 100644
index 0000000..0dfa8c0
--- /dev/null
+++ b/board/ppmc7xx/u-boot.lds
@@ -0,0 +1,135 @@
+/*
+ * (C) Copyright 2001
+ * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * u-boot.lds - linker script for U-Boot on the Galileo Eval Board.
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/74xx_7xx/start.o	(.text)
+
+/* store the environment in a seperate sector in the boot flash */
+/*    . = env_offset; */
+/*    common/environment.o(.text) */
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/tqm5200/Makefile b/board/tqm5200/Makefile
index c234332..ab0ff1a 100644
--- a/board/tqm5200/Makefile
+++ b/board/tqm5200/Makefile
@@ -25,7 +25,6 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-#OBJS	:= $(BOARD).o flash.o
 OBJS	:= $(BOARD).o cmd_stk52xx.o
 
 $(LIB):	$(OBJS) $(SOBJS)
diff --git a/board/tqm5200/flash.c b/board/tqm5200/flash.c
deleted file mode 100644
index af4d78a..0000000
--- a/board/tqm5200/flash.c
+++ /dev/null
@@ -1,497 +0,0 @@
-/*
- * (C) Copyright 2003-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/*
- * CPU to flash interface is 32-bit, so make declaration accordingly
- */
-typedef unsigned long FLASH_PORT_WIDTH;
-typedef volatile unsigned long FLASH_PORT_WIDTHV;
-
-#define FPW	FLASH_PORT_WIDTH
-#define FPWV	FLASH_PORT_WIDTHV
-
-#define FLASH_CYCLE1	0x0555
-#define FLASH_CYCLE2	0x02aa
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size(FPWV *addr, flash_info_t *info);
-static void flash_reset(flash_info_t *info);
-static int write_word_amd(flash_info_t *info, FPWV *dest, FPW data);
-static flash_info_t *flash_get_info(ulong base);
-
-/*-----------------------------------------------------------------------
- * flash_init()
- *
- * sets up flash_info and returns size of FLASH (bytes)
- */
-unsigned long flash_init (void)
-{
-	unsigned long size = 0;
-	extern void flash_preinit(void);
-	ulong flashbase = CFG_FLASH_BASE;
-
-	flash_preinit();
-
-	/* Init: no FLASHes known */
-	memset(&flash_info[0], 0, sizeof(flash_info_t));
-
-	flash_info[0].size =
-		flash_get_size((FPW *)flashbase, &flash_info[0]);
-
-	size = flash_info[0].size;
-
-#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
-	/* monitor protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+monitor_flash_len-1,
-		      flash_get_info(CFG_MONITOR_BASE));
-#endif
-
-#ifdef	CFG_ENV_IS_IN_FLASH
-	/* ENV protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_ENV_ADDR,
-		      CFG_ENV_ADDR+CFG_ENV_SIZE-1,
-		      flash_get_info(CFG_ENV_ADDR));
-#endif
-
-	return size ? size : 1;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_reset(flash_info_t *info)
-{
-	FPWV *base = (FPWV *)(info->start[0]);
-
-	/* Put FLASH back in read mode */
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL)
-		*base = (FPW)0x00FF00FF;	/* Intel Read Mode */
-	else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD)
-		*base = (FPW)0x00F000F0;	/* AMD Read Mode */
-}
-
-/*-----------------------------------------------------------------------
- */
-
-static flash_info_t *flash_get_info(ulong base)
-{
-	int i;
-	flash_info_t * info;
-
-	for (i = 0; i < CFG_MAX_FLASH_BANKS; i ++) {
-		info = & flash_info[i];
-		if (info->size && info->start[0] <= base &&
-		    base <= info->start[0] + info->size - 1)
-			break;
-	}
-
-	return i == CFG_MAX_FLASH_BANKS ? 0 : info;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-void flash_print_info (flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_AMD:	printf ("AMD ");		break;
-	case FLASH_MAN_BM:	printf ("BRIGHT MICRO ");	break;
-	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
-	case FLASH_MAN_SST:	printf ("SST ");		break;
-	case FLASH_MAN_STM:	printf ("STM ");		break;
-	case FLASH_MAN_INTEL:	printf ("INTEL ");		break;
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_AMLV128U:
-		printf ("AM29LV128ML (128Mbit, uniform sector size)\n");
-		break;
-	case FLASH_AM160B:
-		printf ("AM29LV160B (16 Mbit, bottom boot sect)\n");
-		break;
-	default:
-		printf ("Unknown Chip Type\n");
-		break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20,
-		info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0) {
-			printf ("\n   ");
-		}
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     ");
-	}
-	printf ("\n");
-	return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-ulong flash_get_size (FPWV *addr, flash_info_t *info)
-{
-	int i;
-	ulong base = (ulong)addr;
-
-	/* Write auto select command: read Manufacturer ID */
-	/* Write auto select command sequence and test FLASH answer */
-	addr[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* for AMD, Intel ignores this */
-	addr[FLASH_CYCLE2] = (FPW)0x00550055;	/* for AMD, Intel ignores this */
-	addr[FLASH_CYCLE1] = (FPW)0x00900090;	/* selects Intel or AMD */
-
-	/* The manufacturer codes are only 1 byte, so just use 1 byte.
-	 * This works for any bus width and any FLASH device width.
-	 */
-	udelay(100);
-	switch (addr[0] & 0xff) {
-
-	case (uchar)AMD_MANUFACT:
-		debug ("Manufacturer: AMD (Spansion)\n");
-		info->flash_id = FLASH_MAN_AMD;
-		break;
-
-	case (uchar)INTEL_MANUFACT:
-		debug ("Manufacturer: Intel (not supported yet)\n");
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		break;
-	}
-
-	/* Check 16 bits or 32 bits of ID so work on 32 or 16 bit bus. */
-	if (info->flash_id != FLASH_UNKNOWN) switch ((FPW)addr[1]) {
-
-	case (FPW)AMD_ID_LV160B:
-		debug ("Chip: AM29LV160MB\n");
-		info->flash_id += FLASH_AM160B;
-		info->sector_count = 35;
-		info->size = 0x00400000;
-		/*
-		 * The first 4 sectors are 16 kB, 8 kB, 8 kB and 32 kB, all
-		 * the other ones are 64 kB
-		 */
-		info->start[0] = base + 0x00000000;
-		info->start[1] = base + 0x00008000;
-		info->start[2] = base + 0x0000C000;
-		info->start[3] = base + 0x00010000;
-		for( i = 4; i < info->sector_count; i++ )
-			info->start[i] =
-				base + (i * 2 * (64 << 10)) - 0x00060000;
-		break;		/* => 4 MB */
-
-	case AMD_ID_MIRROR:
-		debug ("Mirror Bit flash: addr[14] = %08lX  addr[15] = %08lX\n",
-			addr[14], addr[15]);
-
-		switch(addr[14]) {
-		case AMD_ID_LV128U_2:
-			if (addr[15] != AMD_ID_LV128U_3) {
-				debug ("Chip: AM29LVxxxM -> unknown\n");
-				info->flash_id = FLASH_UNKNOWN;
-				info->sector_count = 0;
-				info->size = 0;
-			} else {
-				debug ("Chip: AM29LV128M\n");
-				info->flash_id += FLASH_AMLV128U;
-				info->sector_count = 256;
-				info->size = 0x02000000;
-				for (i = 0; i < info->sector_count; i++) {
-					info->start[i] = base;
-					base += 0x20000;
-				}
-			}
-			break;	/* => 32 MB	*/
-		default:
-			debug ("Chip: *** unknown ***\n");
-			info->flash_id = FLASH_UNKNOWN;
-			info->sector_count = 0;
-			info->size = 0;
-			break;
-		}
-		break;
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-	}
-
-	/* Put FLASH back in read mode */
-	flash_reset(info);
-
-	return (info->size);
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	vu_long *addr = (vu_long*)(info->start[0]);
-	int flag, prot, sect, l_sect;
-	ulong start, now, last;
-
-	debug ("flash_erase: first: %d last: %d\n", s_first, s_last);
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if ((info->flash_id == FLASH_UNKNOWN) ||
-	    (info->flash_id > FLASH_AMD_COMP)) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-	l_sect = -1;
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-	addr[0x0555] = 0x00800080;
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect<=s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			addr = (vu_long*)(info->start[sect]);
-			addr[0] = 0x00300030;
-			l_sect = sect;
-		}
-	}
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* wait at least 80us - let's wait 1 ms */
-	udelay (1000);
-
-	/*
-	 * We wait for the last triggered sector
-	 */
-	if (l_sect < 0)
-		goto DONE;
-
-	start = get_timer (0);
-	last  = start;
-	addr = (vu_long*)(info->start[l_sect]);
-	while ((addr[0] & 0x00800080) != 0x00800080) {
-		if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-			printf ("Timeout\n");
-			return 1;
-		}
-		/* show that we're waiting */
-		if ((now - last) > 1000) {	/* every second */
-			putc ('.');
-			last = now;
-		}
-	}
-
-DONE:
-	/* reset to read mode */
-	addr = (volatile unsigned long *)info->start[0];
-	addr[0] = 0x00F000F0;	/* reset bank */
-
-	printf (" done\n");
-	return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	/*
-	 * Get lower word aligned address. Assumes 32 bit flash bus width.
-	 */
-	wp = (addr & ~3);
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i=0, cp=wp; i<l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-		for (; i<4 && cnt>0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt==0 && i<4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		if ((rc = write_word_amd(info, (FPW *)wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i=0; i<4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word_amd(info, (FPW *)wp, data)) != 0) {
-			return (rc);
-		}
-		wp  += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i<4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *)cp);
-	}
-
-	return (write_word_amd(info, (FPW *)wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash for AMD FLASH
- * A word is 16 or 32 bits, whichever the bus width of the flash bank
- * (not an individual chip) is.
- *
- * returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word_amd (flash_info_t *info, FPWV *dest, FPW data)
-{
-	ulong start;
-	int flag;
-	FPWV *base;		/* first address in flash bank	*/
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*dest & data) != data) {
-		return (2);
-	}
-
-	base = (FPWV *)(info->start[0]);
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
-	base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
-	base[FLASH_CYCLE1] = (FPW)0x00A000A0;	/* selects program mode */
-
-	*dest = data;		/* start programming the data	*/
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	start = get_timer (0);
-
-	/* data polling for D7 */
-	while ((*dest & (FPW)0x00800080) != (data & (FPW)0x00800080)) {
-		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
-			*dest = (FPW)0x00F000F0;	/* reset bank */
-			return (1);
-		}
-	}
-	return (0);
-}
diff --git a/board/tqm5200/tqm5200.c b/board/tqm5200/tqm5200.c
index 6aad920..310abd2 100644
--- a/board/tqm5200/tqm5200.c
+++ b/board/tqm5200/tqm5200.c
@@ -254,13 +254,7 @@ int checkboard (void)
 	puts ("Board: AEVFIFO\n");
 	return 0;
 #endif
-#if defined (CONFIG_TQM5200_AA)
-	puts ("Board: TQM5200-AA (TQ-Components GmbH)\n");
-#elif defined (CONFIG_TQM5200_AB)
-	puts ("Board: TQM5200-AB (TQ-Components GmbH)\n");
-#elif defined (CONFIG_TQM5200_AC)
-	puts ("Board: TQM5200-AC (TQ-Components GmbH)\n");
-#elif defined (CONFIG_TQM5200)
+#if defined (CONFIG_TQM5200)
 	puts ("Board: TQM5200 (TQ-Components GmbH)\n");
 #endif
 #if defined (CONFIG_STK52XX)
@@ -572,17 +566,7 @@ static const SMI_REGS init_regs [] =
 void video_get_info_str (int line_number, char *info)
 {
 	if (line_number == 1) {
-#if defined (CONFIG_TQM5200_AA)
-		strcpy (info, " Board: TQM5200-AA (TQ-Components GmbH)");
-#elif defined (CONFIG_TQM5200_AB)
-		strcpy (info, " Board: TQM5200-AB (TQ-Components GmbH)");
-#elif defined (CONFIG_TQM5200_AC)
-		strcpy (info, " Board: TQM5200-AC (TQ-Components GmbH)");
-#elif defined (CONFIG_TQM5200)
-		strcpy (info, " Board: TQM5200 (TQ-Components GmbH)");
-#else
-#error No supported board selected
-#endif
+	strcpy (info, " Board: TQM5200 (TQ-Components GmbH)");
 #if defined (CONFIG_STK52XX)
 	} else if (line_number == 2) {
 		strcpy (info, "        on a STK52XX baseboard");
diff --git a/board/tqm834x/tqm834x.c b/board/tqm834x/tqm834x.c
index b5c12e3..d992aec 100644
--- a/board/tqm834x/tqm834x.c
+++ b/board/tqm834x/tqm834x.c
@@ -406,4 +406,28 @@ static void set_ddr_config(void) {
 		(DDR_REFINT_166MHZ_7US << SDRAM_INTERVAL_REFINT_SHIFT) |
 		(DDR_BSTOPRE << SDRAM_INTERVAL_BSTOPRE_SHIFT);
 	SYNC;
+
+	/* Workaround for DDR6 Erratum
+	 * see MPC8349E Device Errata Rev.8, 2/2006
+	 * This workaround influences the MPC internal "input enables"
+	 * dependent on CAS latency and MPC revision. According to errata
+	 * sheet the internal reserved registers for this workaround are
+	 * not available from revision 2.0 and up.
+	 */
+
+	/* Get REVID from register SPRIDR. Skip workaround if rev >= 2.0
+	 * (0x200)
+	 */
+	if ((im->sysconf.spridr & SPRIDR_REVID) < 0x200) {
+
+		/* There is a internal reserved register at IMMRBAR+0x2F00
+		 * which has to be written with a certain value defined by
+		 * errata sheet.
+		 */
+#if defined(DDR_CASLAT_20)
+		*((u8 *)im + 0x2f00) = 0x201c0000;
+#else
+		*((u8 *)im + 0x2f00) = 0x202c0000;
+#endif
+	}
 }
diff --git a/board/tqm85xx/tqm85xx.c b/board/tqm85xx/tqm85xx.c
index 69b9101..befe8b7 100644
--- a/board/tqm85xx/tqm85xx.c
+++ b/board/tqm85xx/tqm85xx.c
@@ -27,6 +27,9 @@
  * MA 02111-1307 USA
  */
 
+#ifdef CONFIG_PS2MULT
+void ps2mult_early_init(void);
+#endif
 
 #include <common.h>
 #include <pci.h>
@@ -410,3 +413,14 @@ void pci_init_board (void)
 	pci_mpc85xx_init (&hose);
 #endif /* CONFIG_PCI */
 }
+
+#ifdef CONFIG_BOARD_EARLY_INIT_R
+int board_early_init_r (void)
+{
+#ifdef CONFIG_PS2MULT
+	ps2mult_early_init();
+#endif /* CONFIG_PS2MULT */
+	return (0);
+}
+#endif /* CONFIG_BOARD_EARLY_INIT_R */
+
diff --git a/board/trab/cmd_trab.c b/board/trab/cmd_trab.c
index 00eb385..edea8f0 100644
--- a/board/trab/cmd_trab.c
+++ b/board/trab/cmd_trab.c
@@ -729,6 +729,7 @@ static void led_blink (void)
 
 	/* blink LED. This function does not return! */
 	while (1) {
+		reset_timer_masked ();
 		led_set (1);
 		udelay (1000000 / LED_BLINK_FREQ / 2);
 		led_set (0);
diff --git a/board/trab/trab.c b/board/trab/trab.c
index 868a899..346406e 100644
--- a/board/trab/trab.c
+++ b/board/trab/trab.c
@@ -161,6 +161,19 @@ int misc_init_r (void)
 	uchar *str;
 	int i;
 
+#ifdef CONFIG_VERSION_VARIABLE
+	{
+		/* Set version variable. Please note, that this variable is
+		 * also set in main_loop() later in the boot process. The
+		 * version variable has to be set this early, because so it
+		 * could be used in script files on an usb stick, which
+		 * might be called during do_auto_update() */
+		extern char version_string[];
+
+		setenv ("ver", version_string);
+	}
+#endif /* CONFIG_VERSION_VARIABLE */
+
 #ifdef CONFIG_AUTO_UPDATE
 	extern int do_auto_update(void);
 	/* this has priority over all else */
diff --git a/board/trab/tsc2000.c b/board/trab/tsc2000.c
index ca68682..382a85b 100644
--- a/board/trab/tsc2000.c
+++ b/board/trab/tsc2000.c
@@ -223,7 +223,7 @@ u16 tsc2000_read_channel (unsigned int channel)
 	u16 res;
 
 	tsc2000_set_mux(channel);
-	udelay(3 * TSC2000_DELAY_BASE);
+	udelay(20 * TSC2000_DELAY_BASE);
 
 	tsc2000_write(TSC2000_REG_ADC, 0x2036);
 	adc_wait_conversion_done ();
diff --git a/board/trab/vfd.c b/board/trab/vfd.c
index cea8b0b..2f1e7d7 100644
--- a/board/trab/vfd.c
+++ b/board/trab/vfd.c
@@ -358,6 +358,8 @@ void transfer_pic(int display, unsigned char *adr, int height, int width)
  */
 int vfd_init_clocks (void)
 {
+	int i;
+
 	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
 	S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS();
 	S3C24X0_LCD * const lcd = S3C24X0_GetBase_LCD();
@@ -367,7 +369,9 @@ int vfd_init_clocks (void)
 	 */
 	gpio->PCUP = (gpio->PCUP & 0xFFF0);	/* activate  GPC0...GPC3 pullups */
 	gpio->PCCON = (gpio->PCCON & 0xFFFFFF00);	/* configure GPC0...GPC3 as inputs */
-	udelay (10);				/* allow signals to settle */
+	/* allow signals to settle */
+	for (i=0; i<10000; i++)	/* udelay isn't working yet at this point! */
+		__asm("NOP");
 	vfd_board_id = (~gpio->PCDAT) & 0x000F;	/* read GPC0...GPC3 port pins */
 
 	VFD_DISABLE;				/* activate blank for the vfd */
diff --git a/board/voiceblue/config.mk b/board/voiceblue/config.mk
index c73cd27..b77c91c 100644
--- a/board/voiceblue/config.mk
+++ b/board/voiceblue/config.mk
@@ -12,5 +12,5 @@ ifeq ($(VOICEBLUE_SMALL_FLASH),y)
 TEXT_BASE = 0x20012000
 else
 # Running in SDRAM...
-TEXT_BASE = 0x13000000
+TEXT_BASE = 0x13FD0000
 endif
diff --git a/common/cmd_ide.c b/common/cmd_ide.c
index 41621ba..a415502 100644
--- a/common/cmd_ide.c
+++ b/common/cmd_ide.c
@@ -855,7 +855,7 @@ output_data_short(int dev, ulong *sect_buf, int words)
 
 /* We only need to swap data if we are running on a big endian cpu. */
 /* But Au1x00 cpu:s already swaps data in big endian mode! */
-#if defined(__LITTLE_ENDIAN) || defined(CONFIG_AU1X00)
+#if defined(__LITTLE_ENDIAN) || ( defined(CONFIG_AU1X00) && !defined(CONFIG_GTH2) )
 #define input_swap_data(x,y,z) input_data(x,y,z)
 #else
 static void
@@ -881,8 +881,13 @@ input_swap_data(int dev, ulong *sect_buf, int words)
 	debug("in input swap data base for read is %lx\n", (unsigned long) pbuf);
 
 	while (words--) {
+#ifdef __MIPS__
+		*dbuf++ = swab16p((u16*)pbuf);
+		*dbuf++ = swab16p((u16*)pbuf);
+#else
 		*dbuf++ = ld_le16(pbuf);
 		*dbuf++ = ld_le16(pbuf);
+#endif /* !MIPS */
 	}
 #endif
 }
diff --git a/common/serial.c b/common/serial.c
index 2acbd08..7b29951 100644
--- a/common/serial.c
+++ b/common/serial.c
@@ -41,7 +41,7 @@ struct serial_device *default_serial_console (void)
    || defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4)
 	return &serial_scc_device;
 #elif defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
-   || defined(CONFIG_405EP)
+   || defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
 	return &serial0_device;
 #else
 #error No default console
@@ -75,7 +75,7 @@ void serial_initialize (void)
 #endif
 
 #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
- || defined(CONFIG_405EP)
+ || defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
 	serial_register(&serial0_device);
 	serial_register(&serial1_device);
 #endif
diff --git a/cpu/74xx_7xx/cpu.c b/cpu/74xx_7xx/cpu.c
index 706c880..ca45e17 100644
--- a/cpu/74xx_7xx/cpu.c
+++ b/cpu/74xx_7xx/cpu.c
@@ -215,7 +215,8 @@ soft_restart(unsigned long addr)
 
 #if !defined(CONFIG_PCIPPC2) && \
     !defined(CONFIG_BAB7xx)  && \
-    !defined(CONFIG_ELPPC)
+    !defined(CONFIG_ELPPC)   && \
+    !defined(CONFIG_PPMC7XX)
 /* no generic way to do board reset. simply call soft_reset. */
 void
 do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
diff --git a/cpu/74xx_7xx/start.S b/cpu/74xx_7xx/start.S
index ff1cce5..1fc0fe6 100644
--- a/cpu/74xx_7xx/start.S
+++ b/cpu/74xx_7xx/start.S
@@ -756,7 +756,8 @@ in_ram:
 #if defined(CONFIG_AMIGAONEG3SE) || \
     defined(CONFIG_DB64360)	 || \
     defined(CONFIG_DB64460)      || \
-    defined(CONFIG_CPCI750)
+    defined(CONFIG_CPCI750)	|| \
+    defined(CONFIG_PPMC7XX)
 	mr	r4, r9		/* Use RAM copy of the global data */
 #endif
 	bl	after_reloc
diff --git a/cpu/arm920t/s3c24x0/i2c.c b/cpu/arm920t/s3c24x0/i2c.c
index ef56cd1..374b683 100644
--- a/cpu/arm920t/s3c24x0/i2c.c
+++ b/cpu/arm920t/s3c24x0/i2c.c
@@ -153,7 +153,7 @@ void i2c_init (int speed, int slaveadd)
 #endif
 #ifdef CONFIG_S3C2400
 		/* set I2CSDA and I2CSCL (PG5, PG6) to GPIO */
-		gpio->PGCON = (gpio->PGCON & ~0x00003c00) | 0x00000c00;
+		gpio->PGCON = (gpio->PGCON & ~0x00003c00) | 0x00001000;
 #endif
 
 		/* toggle I2CSCL until bus idle */
diff --git a/cpu/mpc5xxx/serial.c b/cpu/mpc5xxx/serial.c
index cacb9f0..6cb523d 100644
--- a/cpu/mpc5xxx/serial.c
+++ b/cpu/mpc5xxx/serial.c
@@ -23,6 +23,9 @@
  * Hacked for MPC8260 by Murray.Jensen@cmst.csiro.au, 19-Oct-00, with
  * changes based on the file arch/ppc/mbxboot/m8260_tty.c from the
  * Linux/PPC sources (m8260_tty.c had no copyright info in it).
+ *
+ * Martin Krause, 8 Jun 2006
+ * Added CONFIG_SERIAL_MULTI support
  */
 
 /*
@@ -33,6 +36,10 @@
 #include <common.h>
 #include <mpc5xxx.h>
 
+#if defined (CONFIG_SERIAL_MULTI)
+#include <serial.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 #if defined(CONFIG_PSC_CONSOLE)
@@ -55,9 +62,41 @@ DECLARE_GLOBAL_DATA_PTR;
 #error CONFIG_PSC_CONSOLE must be in 1 ... 6
 #endif
 
+#if defined(CONFIG_SERIAL_MULTI) && !defined(CONFIG_PSC_CONSOLE2)
+#error you must define CONFIG_PSC_CONSOLE2 if CONFIG_SERIAL_MULTI is set
+#endif
+
+#if defined(CONFIG_SERIAL_MULTI)
+#if CONFIG_PSC_CONSOLE2 == 1
+#define PSC_BASE2 MPC5XXX_PSC1
+#elif CONFIG_PSC_CONSOLE2 == 2
+#define PSC_BASE2 MPC5XXX_PSC2
+#elif CONFIG_PSC_CONSOLE2 == 3
+#define PSC_BASE2 MPC5XXX_PSC3
+#elif defined(CONFIG_MGT5100)
+#error CONFIG_PSC_CONSOLE2 must be in 1, 2 or 3
+#elif CONFIG_PSC_CONSOLE2 == 4
+#define PSC_BASE2 MPC5XXX_PSC4
+#elif CONFIG_PSC_CONSOLE2 == 5
+#define PSC_BASE2 MPC5XXX_PSC5
+#elif CONFIG_PSC_CONSOLE2 == 6
+#define PSC_BASE2 MPC5XXX_PSC6
+#else
+#error CONFIG_PSC_CONSOLE2 must be in 1 ... 6
+#endif
+#endif /* CONFIG_SERIAL_MULTI */
+
+#if defined(CONFIG_SERIAL_MULTI)
+int serial_init_dev (unsigned long dev_base)
+#else
 int serial_init (void)
+#endif
 {
+#if defined(CONFIG_SERIAL_MULTI)
+	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)dev_base;
+#else
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
+#endif
 	unsigned long baseclk;
 	int div;
 
@@ -100,13 +139,24 @@ int serial_init (void)
 	return (0);
 }
 
-void
-serial_putc(const char c)
+#if defined(CONFIG_SERIAL_MULTI)
+void serial_putc_dev (unsigned long dev_base, const char c)
+#else
+void serial_putc(const char c)
+#endif
 {
+#if defined(CONFIG_SERIAL_MULTI)
+	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)dev_base;
+#else
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
+#endif
 
 	if (c == '\n')
+#if defined(CONFIG_SERIAL_MULTI)
+		serial_putc_dev (dev_base, '\r');
+#else
 		serial_putc('\r');
+#endif
 
 	/* Wait for last character to go. */
 	while (!(psc->psc_status & PSC_SR_TXEMP))
@@ -115,18 +165,32 @@ serial_putc(const char c)
 	psc->psc_buffer_8 = c;
 }
 
-void
-serial_puts (const char *s)
+#if defined(CONFIG_SERIAL_MULTI)
+void serial_puts_dev (unsigned long dev_base, const char *s)
+#else
+void serial_puts (const char *s)
+#endif
 {
 	while (*s) {
+#if defined(CONFIG_SERIAL_MULTI)
+		serial_putc_dev (dev_base, *s++);
+#else
 		serial_putc (*s++);
+#endif
 	}
 }
 
-int
-serial_getc(void)
+#if defined(CONFIG_SERIAL_MULTI)
+int serial_getc_dev (unsigned long dev_base)
+#else
+int serial_getc(void)
+#endif
 {
+#if defined(CONFIG_SERIAL_MULTI)
+	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)dev_base;
+#else
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
+#endif
 
 	/* Wait for a character to arrive. */
 	while (!(psc->psc_status & PSC_SR_RXRDY))
@@ -135,18 +199,32 @@ serial_getc(void)
 	return psc->psc_buffer_8;
 }
 
-int
-serial_tstc(void)
+#if defined(CONFIG_SERIAL_MULTI)
+int serial_tstc_dev (unsigned long dev_base)
+#else
+int serial_tstc(void)
+#endif
 {
+#if defined(CONFIG_SERIAL_MULTI)
+	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)dev_base;
+#else
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
+#endif
 
 	return (psc->psc_status & PSC_SR_RXRDY);
 }
 
-void
-serial_setbrg(void)
+#if defined(CONFIG_SERIAL_MULTI)
+void serial_setbrg_dev (unsigned long dev_base)
+#else
+void serial_setbrg(void)
+#endif
 {
+#if defined(CONFIG_SERIAL_MULTI)
+	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)dev_base;
+#else
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
+#endif
 	unsigned long baseclk, div;
 
 #if defined(CONFIG_MGT5100)
@@ -160,4 +238,87 @@ serial_setbrg(void)
 	psc->ctur = (div >> 8) & 0xFF;
 	psc->ctlr =  div & 0xff;
 }
+
+#if defined(CONFIG_SERIAL_MULTI)
+int serial0_init(void)
+{
+	return (serial_init_dev(PSC_BASE));
+}
+
+int serial1_init(void)
+{
+	return (serial_init_dev(PSC_BASE2));
+}
+void serial0_setbrg (void)
+{
+	serial_setbrg_dev(PSC_BASE);
+}
+void serial1_setbrg (void)
+{
+	serial_setbrg_dev(PSC_BASE2);
+}
+
+void serial0_putc(const char c)
+{
+	serial_putc_dev(PSC_BASE,c);
+}
+
+void serial1_putc(const char c)
+{
+	serial_putc_dev(PSC_BASE2, c);
+}
+void serial0_puts(const char *s)
+{
+	serial_puts_dev(PSC_BASE, s);
+}
+
+void serial1_puts(const char *s)
+{
+	serial_puts_dev(PSC_BASE2, s);
+}
+
+int serial0_getc(void)
+{
+	return(serial_getc_dev(PSC_BASE));
+}
+
+int serial1_getc(void)
+{
+	return(serial_getc_dev(PSC_BASE2));
+}
+int serial0_tstc(void)
+{
+	return (serial_tstc_dev(PSC_BASE));
+}
+
+int serial1_tstc(void)
+{
+	return (serial_tstc_dev(PSC_BASE2));
+}
+
+struct serial_device serial0_device =
+{
+	"serial0",
+	"UART0",
+	serial0_init,
+	serial0_setbrg,
+	serial0_getc,
+	serial0_tstc,
+	serial0_putc,
+	serial0_puts,
+};
+
+struct serial_device serial1_device =
+{
+	"serial1",
+	"UART1",
+	serial1_init,
+	serial1_setbrg,
+	serial1_getc,
+	serial1_tstc,
+	serial1_putc,
+	serial1_puts,
+};
+#endif /* CONFIG_SERIAL_MULTI */
+
 #endif /* CONFIG_PSC_CONSOLE */
diff --git a/doc/README.serial_multi b/doc/README.serial_multi
index a8d48fc..40f7815 100644
--- a/doc/README.serial_multi
+++ b/doc/README.serial_multi
@@ -52,3 +52,29 @@ PPC4XX Specific
 	setenv stdout serial0
 	setenv stderr serial0
 	setenv stdin serial0
+
+MPC5xxx Specific
+================
+
+Up to two PSCs can be used as console.
+
+Support for hardware handshake has not been implemented yet.
+
+*) The first (default) console port is defined by:
+	#define CONFIG_PSC_CONSOLE <PSC number>
+
+*) The second (alternative) console port is defined by:
+	#define CONFIG_PSC_CONSOLE2 <PSC number>
+
+*) Commands to switch to the second console:
+	setenv stdout serial1
+	setenv stderr serial1
+	setenv stdin serial1
+
+*) Commands to switch to the first console:
+	setenv stdout serial0
+	setenv stderr serial0
+	setenv stdin serial0
+
+*) If a file descriptor is set to "serial" then the
+   current serial device will be used.
diff --git a/drivers/keyboard.c b/drivers/keyboard.c
index 1579095..41eccf2 100644
--- a/drivers/keyboard.c
+++ b/drivers/keyboard.c
@@ -33,7 +33,7 @@
 
 #define	KBD_BUFFER_LEN		0x20  /* size of the keyboardbuffer */
 
-#ifdef CONFIG_MPC5xxx
+#if defined(CONFIG_MPC5xxx) || defined(CONFIG_MPC85xx)
 int ps2ser_check(void);
 #endif
 
@@ -75,7 +75,7 @@ static void kbd_put_queue(char data)
 /* test if a character is in the queue */
 static int kbd_testc(void)
 {
-#ifdef CONFIG_MPC5xxx
+#if defined(CONFIG_MPC5xxx) || defined(CONFIG_MPC85xx)
 	/* no ISR is used, so received chars must be polled */
 	ps2ser_check();
 #endif
@@ -90,7 +90,7 @@ static int kbd_getc(void)
 {
 	char c;
 	while(in_pointer==out_pointer) {
-#ifdef CONFIG_MPC5xxx
+#if defined(CONFIG_MPC5xxx) || defined(CONFIG_MPC85xx)
 	/* no ISR is used, so received chars must be polled */
 	ps2ser_check();
 #endif
diff --git a/drivers/pci.c b/drivers/pci.c
index 3c24b99..050582f 100644
--- a/drivers/pci.c
+++ b/drivers/pci.c
@@ -163,7 +163,7 @@ pci_dev_t pci_find_devices(struct pci_device_id *ids, int index)
 		for (bus = hose->first_busno; bus <= hose->last_busno; bus++)
 #endif
 			for (bdf = PCI_BDF(bus,0,0);
-#ifdef CONFIG_ELPPC
+#if defined(CONFIG_ELPPC) || defined(CONFIG_PPMC7XX)
 			     bdf < PCI_BDF(bus,PCI_MAX_PCI_DEVICES-1,PCI_MAX_PCI_FUNCTIONS-1);
 #else
 			     bdf < PCI_BDF(bus+1,0,0);
diff --git a/drivers/ps2ser.c b/drivers/ps2ser.c
index 724fa40..8aea8fd 100644
--- a/drivers/ps2ser.c
+++ b/drivers/ps2ser.c
@@ -20,6 +20,9 @@
 #include <asm/io.h>
 #include <asm/atomic.h>
 #include <ps2mult.h>
+#ifdef CFG_NS16550
+#include <ns16550.h>
+#endif
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -45,13 +48,24 @@ DECLARE_GLOBAL_DATA_PTR;
 #else
 #error CONFIG_PS2SERIAL must be in 1 ... 6
 #endif
-#endif /* CONFIG_MPC5xxx */
+
+#elif defined(CONFIG_MPC85xx)
+
+#if CONFIG_PS2SERIAL == 1
+#define COM_BASE (CFG_CCSRBAR+0x4500)
+#elif CONFIG_PS2SERIAL == 2
+#define COM_BASE (CFG_CCSRBAR+0x4600)
+#else
+#error CONFIG_PS2SERIAL must be in 1 ... 2
+#endif
+
+#endif /* CONFIG_MPC5xxx / CONFIG_MPC85xx */
 
 static int	ps2ser_getc_hw(void);
 static void	ps2ser_interrupt(void *dev_id);
 
 extern struct	serial_state rs_table[]; /* in serial.c */
-#ifndef CONFIG_MPC5xxx
+#if !defined(CONFIG_MPC5xxx) && !defined(CONFIG_MPC85xx)
 static struct	serial_state *state;
 #endif
 
@@ -106,7 +120,23 @@ int ps2ser_init(void)
 	return (0);
 }
 
-#else /* !CONFIG_MPC5xxx */
+#elif defined(CONFIG_MPC85xx)
+int ps2ser_init(void)
+{
+	NS16550_t com_port = (NS16550_t)COM_BASE;
+
+	com_port->ier = 0x00;
+	com_port->lcr = LCR_BKSE | LCR_8N1;
+	com_port->dll = (CFG_NS16550_CLK / 16 / PS2SER_BAUD) & 0xff;
+	com_port->dlm = ((CFG_NS16550_CLK / 16 / PS2SER_BAUD) >> 8) & 0xff;
+	com_port->lcr = LCR_8N1;
+	com_port->mcr = (MCR_DTR | MCR_RTS);
+	com_port->fcr = (FCR_FIFO_EN | FCR_RXSR | FCR_TXSR);
+
+	return (0);
+}
+
+#else /* !CONFIG_MPC5xxx && !CONFIG_MPC85xx */
 
 static inline unsigned int ps2ser_in(int offset)
 {
@@ -150,12 +180,14 @@ int ps2ser_init(void)
 
 	return 0;
 }
-#endif /* CONFIG_MPC5xxx */
+#endif /* CONFIG_MPC5xxx / CONFIG_MPC85xx / other */
 
 void ps2ser_putc(int chr)
 {
 #ifdef CONFIG_MPC5xxx
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
+#elif defined(CONFIG_MPC85xx)
+	NS16550_t com_port = (NS16550_t)COM_BASE;
 #endif
 #ifdef DEBUG
 	printf(">>>> 0x%02x\n", chr);
@@ -165,6 +197,9 @@ void ps2ser_putc(int chr)
 	while (!(psc->psc_status & PSC_SR_TXRDY));
 
 	psc->psc_buffer_8 = chr;
+#elif defined(CONFIG_MPC85xx)
+	while ((com_port->lsr & LSR_THRE) == 0);
+	com_port->thr = chr;
 #else
 	while (!(ps2ser_in(UART_LSR) & UART_LSR_THRE));
 
@@ -176,6 +211,8 @@ static int ps2ser_getc_hw(void)
 {
 #ifdef CONFIG_MPC5xxx
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
+#elif defined(CONFIG_MPC85xx)
+	NS16550_t com_port = (NS16550_t)COM_BASE;
 #endif
 	int res = -1;
 
@@ -183,6 +220,10 @@ static int ps2ser_getc_hw(void)
 	if (psc->psc_status & PSC_SR_RXRDY) {
 		res = (psc->psc_buffer_8);
 	}
+#elif defined(CONFIG_MPC85xx)
+	if (com_port->lsr & LSR_DR) {
+		res = com_port->rbr;
+	}
 #else
 	if (ps2ser_in(UART_LSR) & UART_LSR_DR) {
 		res = (ps2ser_in(UART_RX));
@@ -238,6 +279,8 @@ static void ps2ser_interrupt(void *dev_id)
 {
 #ifdef CONFIG_MPC5xxx
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
+#elif defined(CONFIG_MPC85xx)
+	NS16550_t com_port = (NS16550_t)COM_BASE;
 #endif
 	int chr;
 	int status;
@@ -246,6 +289,8 @@ static void ps2ser_interrupt(void *dev_id)
 		chr = ps2ser_getc_hw();
 #ifdef CONFIG_MPC5xxx
 		status = psc->psc_status;
+#elif defined(CONFIG_MPC85xx)
+		status = com_port->lsr;
 #else
 		status = ps2ser_in(UART_IIR);
 #endif
@@ -260,6 +305,8 @@ static void ps2ser_interrupt(void *dev_id)
 		}
 #ifdef CONFIG_MPC5xxx
 	} while (status & PSC_SR_RXRDY);
+#elif defined(CONFIG_MPC85xx)
+	} while (status & LSR_DR);
 #else
 	} while (status & UART_IIR_RDI);
 #endif
diff --git a/include/asm-mips/au1x00.h b/include/asm-mips/au1x00.h
index 4e19dc4..a4e9947 100644
--- a/include/asm-mips/au1x00.h
+++ b/include/asm-mips/au1x00.h
@@ -119,6 +119,11 @@ static __inline__ int au_ffs(int x)
 	return __ilog2(x & -x) + 1;
 }
 
+#define gpio_set(Value)      outl(Value, SYS_OUTPUTSET)
+#define gpio_clear(Value)    outl(Value, SYS_OUTPUTCLR)
+#define gpio_read()          inl(SYS_PINSTATERD)
+#define gpio_tristate(Value) outl(Value, SYS_TRIOUTCLR)
+
 #endif /* !ASSEMBLY */
 
 #ifdef CONFIG_PM
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 6020998..6b8759f 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -37,7 +37,6 @@
 #define CONFIG_TQM5200		1	/* ... on TQM5200 module */
 #undef CONFIG_TQM5200_REV100		/*  define for revision 100 modules */
 #define CONFIG_STK52XX		1	/* ... on a STK52XX base board */
-#define CONFIG_STK52XX_REV100	1	/*  define for revision 100 baseboards */
 
 #define CFG_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */
 
@@ -83,7 +82,7 @@
 #define CONFIG_PCI_IO_SIZE	0x01000000
 
 #define CONFIG_NET_MULTI	1
-#define CONFIG_EEPRO100
+#define CONFIG_EEPRO100		1
 #define CFG_RX_ETH_BUFFER	8  /* use 8 rx buffer on eepro100  */
 #define CONFIG_NS8382X		1
 #endif	/* CONFIG_STK52XX */
@@ -192,16 +191,6 @@
 
 #undef	CONFIG_BOOTARGS
 
-#if defined (CONFIG_TQM5200_AA)
-# define CONFIG_U_BOOT_SUFFIX	"-AA\0"
-#elif defined (CONFIG_TQM5200_AB)
-# define CONFIG_U_BOOT_SUFFIX	"-AB\0"
-#elif defined (CONFIG_TQM5200_AC)
-# define CONFIG_U_BOOT_SUFFIX	"-AC\0"
-#else
-# define CONFIG_U_BOOT_SUFFIX	"\0"
-#endif
-
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"rootpath=/opt/eldk/ppc_6xx\0"					\
@@ -218,7 +207,7 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"bootfile=/tftpboot/tqm5200/uImage\0"				\
 	"load=tftp 200000 ${u-boot}\0"					\
-	"u-boot=/tftpboot/tqm5200/u-boot.bin"	CONFIG_U_BOOT_SUFFIX	\
+	"u-boot=/tftpboot/tqm5200/u-boot.bin\0"				\
 	"update=protect off FC000000 FC05FFFF;"				\
 		"erase FC000000 FC05FFFF;"				\
 		"cp.b 200000 FC000000 ${filesize};"			\
@@ -284,13 +273,6 @@
 #endif
 
 /* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AB)
-#define I2C_ADDR_LIST	{	CFG_I2C_EEPROM_ADDR,	\
-				CFG_I2C_SLAVE }
-#elif defined (CONFIG_TQM5200_AC)
-#define I2C_ADDR_LIST	{	CFG_I2C_SLAVE }
-#endif
-
 #if defined (CONFIG_MINIFAP)
 #undef I2C_ADDR_LIST
 #define I2C_ADDR_LIST	{	CFG_I2C_EEPROM_ADDR,	\
@@ -493,13 +475,9 @@
  * SRAM - Do not map below 2 GB in address space, because this area is used
  * for SDRAM autosizing.
  */
-#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
 #define CFG_CS2_START		0xE5000000
-#ifdef CONFIG_TQM5200_AB
-#define CFG_CS2_SIZE		0x80000		/* 512 kByte */
-#else  /* CONFIG_CS_AUTOCONF */
 #define CFG_CS2_SIZE		0x100000	/* 1 MByte */
-#endif
 #define CFG_CS2_CFG		0x0004D930
 #endif
 
@@ -507,8 +485,7 @@
  * Grafic controller - Do not map below 2 GB in address space, because this
  * area is used for SDRAM autosizing.
  */
-#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \
-    defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
 #define SM501_FB_BASE		0xE0000000
 #define CFG_CS1_START		(SM501_FB_BASE)
 #define CFG_CS1_SIZE		0x4000000	/* 64 MByte */
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index 18197f2..da6946b 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -177,6 +177,13 @@
 #define CFG_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
+/* PS/2 Keyboard */
+#define CONFIG_PS2KBD			/* AT-PS/2 Keyboard		*/
+#define CONFIG_PS2MULT			/* .. on PS/2 Multiplexer	*/
+#define CONFIG_PS2SERIAL	2	/* .. on DUART2			*/
+#define CONFIG_PS2MULT_DELAY	(CFG_HZ/2)	/* Initial delay	*/
+#define CONFIG_BOARD_EARLY_INIT_R	1
+
 /* Use the HUSH parser */
 #define CFG_HUSH_PARSER
 #ifdef	CFG_HUSH_PARSER
diff --git a/include/configs/cmc_pu2.h b/include/configs/cmc_pu2.h
index 46280f7..572a70f 100644
--- a/include/configs/cmc_pu2.h
+++ b/include/configs/cmc_pu2.h
@@ -108,7 +108,7 @@
 /* still about 20 kB free with this defined */
 #define CFG_LONGHELP
 
-#define CONFIG_BOOTDELAY      3
+#define CONFIG_BOOTDELAY      1
 
 #ifdef CONFIG_HARD_I2C
 #define CONFIG_COMMANDS		\
@@ -206,15 +206,6 @@ struct bd_info_ext {
 #error CONFIG_USE_IRQ not supported
 #endif
 
-#define CFG_DEVICE_NULLDEV	 1	/* enble null device		*/
-#define CONFIG_SILENT_CONSOLE	 1	/* enable silent startup	*/
-
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n"
-#define CONFIG_AUTOBOOT_STOP_STR "R"	/* default password */
-
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
-
 #define	CONFIG_EXTRA_ENV_SETTINGS	\
 	"net_nfs=tftp ${loadaddr} ${bootfile};run nfsargs addip addcons " \
 		"addmtd;bootm\0" \
diff --git a/include/configs/gth2.h b/include/configs/gth2.h
new file mode 100644
index 0000000..77d2d56
--- /dev/null
+++ b/include/configs/gth2.h
@@ -0,0 +1,195 @@
+/*
+ * (C) Copyright 2005
+ * Thomas.Lange@corelatus.se
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * This file contains the configuration parameters for the gth2 board.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MIPS32		1  /* MIPS32 CPU core	*/
+#define CONFIG_GTH2		1
+#define CONFIG_AU1X00		1  /* alchemy series cpu */
+
+#define CONFIG_AU1000		1
+
+#define CONFIG_MISC_INIT_R      1
+
+#define CONFIG_ETHADDR		DE:AD:BE:EF:01:02    /* Ethernet address */
+
+#define CONFIG_BOOTDELAY	1	/* autoboot after 1 seconds	*/
+
+#define CONFIG_ENV_OVERWRITE 1 /* Allow change of ethernet address */
+
+#define CONFIG_BOOT_RETRY_TIME 5 /* Retry boot in 5 secs */
+
+#define CONFIG_RESET_TO_RETRY 1 /* If timeout waiting for command, perform a reset */
+
+#define CONFIG_BAUDRATE		115200
+
+/* valid baudrates */
+#define CFG_BAUDRATE_TABLE	{ 115200 }
+
+/* Only interrupt boot if space is pressed */
+/* If a long serial cable is connected but */
+/* other end is dead, garbage will be read */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Press space to abort autoboot in %d second\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "d"
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+#define	CONFIG_TIMESTAMP		/* Print image info with timestamp */
+#define	CONFIG_BOOTARGS "panic=1"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"addmisc=setenv bootargs $(bootargs) "				\
+	        "ethaddr=$(ethaddr) \0"					\
+        "netboot=bootp;run addmisc;bootm\0"                             \
+                ""
+
+/* Boot from Compact flash partition 2 as default */
+#define CONFIG_BOOTCOMMAND	"ide reset;disk 0x81000000 0:2;run addmisc;bootm"
+
+#define CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_IDE | CFG_CMD_DHCP ) & \
+ ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | \
+   CFG_CMD_MII | CFG_CMD_LOADS  | CFG_CMD_LOADB | CFG_CMD_ELF | \
+   CFG_CMD_BDI | CFG_CMD_BEDBUG | CFG_CMD_NFS | CFG_CMD_AUTOSCRIPT ))
+
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP				/* undef to save memory      */
+#define	CFG_PROMPT		"GTH2 # "	/* Monitor Command Prompt    */
+#define	CFG_CBSIZE		256		/* Console I/O Buffer Size   */
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)  /* Print Buffer Size */
+#define	CFG_MAXARGS		16		/* max number of command args*/
+
+#define CFG_MALLOC_LEN		128*1024
+
+#define CFG_BOOTPARAMS_LEN	128*1024
+
+#define CFG_MHZ			500
+
+#define CFG_HZ                  (CFG_MHZ * 1000000) /* FIXME causes overflow in net.c */
+
+#define CFG_SDRAM_BASE		0x80000000     /* Cached addr */
+
+#define	CFG_LOAD_ADDR		0x81000000     /* default load address	*/
+
+#define CFG_MEMTEST_START	0x80100000
+#define CFG_MEMTEST_END		0x83000000
+
+#define CONFIG_HW_WATCHDOG      1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	(128)	/* max number of sectors on one chip */
+
+#define PHYS_FLASH		0xbfc00000 /* Flash Bank #1 */
+
+/* The following #defines are needed to get flash environment right */
+#define	CFG_MONITOR_BASE	TEXT_BASE
+#define	CFG_MONITOR_LEN		(192 << 10)
+
+#define CFG_INIT_SP_OFFSET	0x400000
+
+/* We boot from this flash, selected with dip switch */
+#define CFG_FLASH_BASE		PHYS_FLASH
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT	(2 * CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT	(2 * CFG_HZ) /* Timeout for Flash Write */
+
+#define	CFG_ENV_IS_NOWHERE	1
+
+/* Address and size of Primary Environment Sector	*/
+#define CFG_ENV_ADDR		0xB0030000
+#define CFG_ENV_SIZE		0x10000
+
+#define CONFIG_FLASH_16BIT
+
+#define CONFIG_NR_DRAM_BANKS	2
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_MEMSIZE_IN_BYTES
+
+/*---ATA PCMCIA ------------------------------------*/
+#define CFG_PCMCIA_MEM_SIZE 0x4000000 /* Offset to slot 1 FIXME!!! */
+
+#define CFG_PCMCIA_MEM_ADDR  0x20000000
+#define CFG_PCMCIA_IO_BASE   0x28000000
+#define CFG_PCMCIA_ATTR_BASE 0x30000000
+
+#define CONFIG_PCMCIA_SLOT_A
+
+#define CONFIG_ATAPI 1
+#define CONFIG_MAC_PARTITION 1
+
+/* We run CF in "true ide" mode or a harddrive via pcmcia */
+#define CONFIG_IDE_PCMCIA 1
+
+/* We only support one slot for now */
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
+#define CFG_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
+
+#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
+#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
+
+#define CFG_ATA_IDE0_OFFSET	0
+
+#define CFG_ATA_BASE_ADDR       CFG_PCMCIA_IO_BASE
+
+/* Offset for data I/O			*/
+#define CFG_ATA_DATA_OFFSET     0
+
+/* Offset for normal register accesses  */
+#define CFG_ATA_REG_OFFSET      0
+
+/* Offset for alternate registers       */
+#define CFG_ATA_ALT_OFFSET      0x0200
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		16384
+#define CFG_ICACHE_SIZE		16384
+#define CFG_CACHELINE_SIZE	32
+
+#define GPIO_CACONFIG  (1<<0)
+#define GPIO_DPACONFIG (1<<6)
+#define GPIO_ERESET    (1<<11)
+#define GPIO_EEDQ      (1<<17)
+#define GPIO_WDI       (1<<18)
+#define GPIO_RJ1LY     (1<<22)
+#define GPIO_RJ1LG     (1<<23)
+#define GPIO_LEDCLK    (1<<29)
+#define GPIO_LEDD      (1<<30)
+#define GPIO_CPU_LED   (1<<31)
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/ppmc7xx.h b/include/configs/ppmc7xx.h
new file mode 100644
index 0000000..ea15524
--- /dev/null
+++ b/include/configs/ppmc7xx.h
@@ -0,0 +1,419 @@
+/*
+ * ppmc7xx.h
+ * ---------
+ * 
+ * Wind River PPMC 7xx/74xx board configuration file.
+ * 
+ * By Richard Danter (richard.danter@windriver.com)
+ * Copyright (C) 2005 Wind River Systems
+ */
+
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_PPMC7XX
+
+
+/*===================================================================
+ * 
+ * User configurable settings - Modify to your preference
+ * 
+ *===================================================================
+ */
+
+/*
+ * Debug
+ * 
+ * DEBUG			- Define this is you want extra debug info
+ * GTREGREAD			- Required to build with debug
+ * do_bdinfo			- Required to build with debug
+ */
+
+#undef	DEBUG
+#define	GTREGREAD(x)			0xFFFFFFFF
+#define	do_bdinfo(a,b,c,d)
+
+
+/*
+ * CPU type
+ * 
+ * CONFIG_7xx			- We have a 750 or 755 CPU
+ * CONFIG_74xx			- We have a 7400 CPU
+ * CONFIG_ALTIVEC		- We have altivec enabled CPU (only 7400)
+ * CONFIG_BUS_CLK		- System bus clock in Hz
+ */
+
+#define	CONFIG_7xx
+#undef	CONFIG_74xx
+#undef	CONFIG_ALTIVEC
+#define CONFIG_BUS_CLK			66000000
+
+
+/*
+ * Monitor configuration
+ * 
+ * CONFIG_COMMANDS		- List of command sets to include in shell
+ * 
+ * The following command sets have been tested and known to work:
+ * 
+ * CFG_CMD_CACHE		- Cache control commands
+ * CFG_CMD_MEMORY		- Memory display, change and test commands
+ * CFG_CMD_FLASH		- Erase and program flash
+ * CFG_CMD_ENV			- Environment commands
+ * CFG_CMD_RUN			- Run commands stored in env vars
+ * CFG_CMD_ELF			- Load ELF files
+ * CFG_CMD_NET			- Networking/file download commands
+ * CFG_CMD_PING			- ICMP Echo Request command
+ * CFG_CMD_PCI			- PCI Bus scanning command
+ */
+
+#define CONFIG_COMMANDS		( (CFG_CMD_DFL & ~(CFG_CMD_KGDB)) |	\
+						   CFG_CMD_FLASH |	\
+						   CFG_CMD_ENV |	\
+						   CFG_CMD_RUN |	\
+						   CFG_CMD_ELF |	\
+						   CFG_CMD_NET |	\
+						   CFG_CMD_PING |	\
+						   CFG_CMD_PCI)
+
+
+/*
+ * Serial configuration
+ *
+ * CONFIG_CONS_INDEX		- Serial console port number (COM1)
+ * CONFIG_BAUDRATE			- Serial speed
+ */
+
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			9600
+
+
+/*
+ * PCI config
+ * 
+ * CONFIG_PCI				- Enable PCI bus
+ * CONFIG_PCI_PNP			- Enable Plug & Play support
+ * CONFIG_PCI_SCAN_SHOW		- Enable display of devices at startup
+ */
+
+#define	CONFIG_PCI
+#define	CONFIG_PCI_PNP
+#undef	CONFIG_PCI_SCAN_SHOW
+
+
+/*
+ * Network config
+ * 
+ * CONFIG_NET_MULTI			- Support for multiple network interfaces
+ * CONFIG_EEPRO100			- Intel 8255x Ethernet Controller
+ * CONFIG_EEPRO100_SROM_WRITE - Enable writing to network card ROM
+ */
+
+#define	CONFIG_NET_MULTI
+#define	CONFIG_EEPRO100
+#define	CONFIG_EEPRO100_SROM_WRITE
+
+
+/*
+ * Enable extra init functions
+ * 
+ * CONFIG_MISC_INIT_F		- Call pre-relocation init functions
+ * CONFIG_MISC_INIT_R		- Call post relocation init functions
+ */
+
+#undef	CONFIG_MISC_INIT_F
+#define CONFIG_MISC_INIT_R 
+
+
+/*
+ * Boot config
+ * 
+ * CONFIG_BOOTCOMMAND		- Command(s) to execute to auto-boot
+ * CONFIG_BOOTDELAY			- How long to wait before auto-boot (in sec)
+ */
+
+#define CONFIG_BOOTCOMMAND		\
+	"bootp;" \
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
+	"bootm"
+#define CONFIG_BOOTDELAY		5
+
+
+/*===================================================================
+ * 
+ * Board configuration settings - You should not need to modify these
+ * 
+ *===================================================================
+ */
+
+
+#include <cmd_confdefs.h>
+
+
+/*
+ * Memory map
+ * 
+ * This board runs in a standard CHRP (Map-B) configuration.
+ * 
+ *	Type		Start		End			Size	Width	Chip Sel
+ *	----------- ----------- ----------- ------- ------- --------
+ *	SDRAM		0x00000000	0x04000000	64MB	64b		SDRAMCS0
+ *	User LED's	0x78000000						RCS3
+ *	UART		0x7C000000						RCS2
+ *	Mailbox		0xFF000000						RCS1
+ *	Flash		0xFFC00000	0xFFFFFFFF	4MB	64b		RCS0
+ * 
+ * Flash sectors are laid out as follows.
+ * 
+ *	Sector	Start		End			Size	Comments
+ *	------- ----------- ----------- ------- -----------
+ *	 0		0xFFC00000	0xFFC3FFFF	256KB
+ *   1		0xFFC40000	0xFFC7FFFF	256KB
+ *	 2		0xFFC80000	0xFFCBFFFF	256KB
+ *	 3		0xFFCC0000	0xFFCFFFFF	256KB
+ *	 4		0xFFD00000	0xFFD3FFFF	256KB
+ *	 5		0xFFD40000	0xFFD7FFFF	256KB
+ *	 6		0xFFD80000	0xFFDBFFFF	256KB
+ *	 7		0xFFDC0000	0xFFDFFFFF	256KB
+ *   8		0xFFE00000	0xFFE3FFFF	256KB
+ *	 9		0xFFE40000	0xFFE7FFFF	256KB
+ *  10		0xFFE80000	0xFFEBFFFF	256KB
+ *  11		0xFFEC0000	0xFFEFFFFF	256KB
+ *  12		0xFFF00000	0xFFF3FFFF	256KB	U-Boot code here
+ *  13		0xFFF40000	0xFFF7FFFF	256KB
+ *  14		0xFFF80000	0xFFFBFFFF	256KB
+ *  15		0xFFFC0000	0xFFFDFFFF	128KB
+ *  16		0xFFFE0000	0xFFFE7FFF	 32KB	U-Boot env vars here
+ *  17		0xFFFE8000	0xFFFEFFFF	 32KB	U-Boot backup copy of env vars here
+ *  18		0xFFFF0000	0xFFFFFFFF	 64KB
+ */
+
+
+/*
+ * SDRAM config - see memory map details above.
+ * 
+ * CFG_SDRAM_BASE			- Start address of SDRAM, this _must_ be zero!
+ * CFG_SDRAM_SIZE			- Total size of contiguous SDRAM bank(s)
+ */
+
+#define CFG_SDRAM_BASE			0x00000000
+#define CFG_SDRAM_SIZE			0x04000000
+
+
+/* 
+ * Flash config - see memory map details above.
+ * 
+ * CFG_FLASH_BASE			- Start address of flash memory
+ * CFG_FLASH_SIZE			- Total size of contiguous flash mem
+ * CFG_FLASH_ERASE_TOUT		- Erase timeout in ms
+ * CFG_FLASH_WRITE_TOUT		- Write timeout in ms
+ * CFG_MAX_FLASH_BANKS		- Number of banks of flash on board
+ * CFG_MAX_FLASH_SECT		- Number of sectors in a bank
+ */
+
+#define CFG_FLASH_BASE			0xFFC00000
+#define CFG_FLASH_SIZE			0x00400000
+#define CFG_FLASH_ERASE_TOUT	250000
+#define CFG_FLASH_WRITE_TOUT	5000
+#define CFG_MAX_FLASH_BANKS		1
+#define CFG_MAX_FLASH_SECT		19
+
+
+/*
+ * Monitor config - see memory map details above
+ * 
+ * CFG_MONITOR_BASE			- Base address of monitor code
+ * CFG_MALLOC_LEN			- Size of malloc pool (128KB)
+ */
+
+#define CFG_MONITOR_BASE		TEXT_BASE
+#define CFG_MALLOC_LEN			0x20000
+
+
+/*
+ * Command shell settings
+ * 
+ * CFG_BARGSIZE			- Boot Argument buffer size
+ * CFG_BOOTMAPSZ		- Size of app's mapped RAM at boot (Linux=8MB)
+ * CFG_CBSIZE			- Console Buffer (input) size
+ * CFG_LOAD_ADDR		- Default load address
+ * CFG_LONGHELP			- Provide more detailed help
+ * CFG_MAXARGS			- Number of args accepted by monitor commands
+ * CFG_MEMTEST_START		- Start address of test to run on RAM
+ * CFG_MEMTEST_END		- End address of RAM test
+ * CFG_PBSIZE			- Print Buffer (output) size
+ * CFG_PROMPT			- Prompt string
+ */
+
+#define CFG_BARGSIZE			1024
+#define CFG_BOOTMAPSZ			0x800000
+#define CFG_CBSIZE			1024
+#define CFG_LOAD_ADDR			0x100000
+#define CFG_LONGHELP
+#define CFG_MAXARGS			16
+#define CFG_MEMTEST_START		0x00040000
+#define CFG_MEMTEST_END			0x00040100
+#define CFG_PBSIZE			1024
+#define CFG_PROMPT			"=> "
+
+
+/*
+ * Environment config - see memory map details above
+ * 
+ * CFG_ENV_IS_IN_FLASH		- The env variables are stored in flash
+ * CFG_ENV_ADDR			- Address of the sector containing env vars
+ * CFG_ENV_SIZE			- Ammount of RAM for env vars (used to save RAM, 4KB) 
+ * CFG_ENV_SECT_SIZE		- Size of sector containing env vars (32KB)
+ */
+
+#define CFG_ENV_IS_IN_FLASH		1
+#define CFG_ENV_ADDR			0xFFFE0000
+#define CFG_ENV_SIZE			0x1000
+#define CFG_ENV_ADDR_REDUND		0xFFFE8000
+#define CFG_ENV_SIZE_REDUND		0x1000
+#define CFG_ENV_SECT_SIZE		0x8000
+
+
+/*
+ * Initial RAM config
+ *
+ * Since the main system RAM is initialised very early, we place the INIT_RAM
+ * in the main system RAM just above the exception vectors. The contents are
+ * copied to top of RAM by the init code.
+ * 
+ * CFG_INIT_RAM_ADDR		- Address of Init RAM, above exception vect
+ * CFG_INIT_RAM_END			- Size of Init RAM
+ * CFG_GBL_DATA_SIZE		- Ammount of RAM to reserve for global data
+ * CFG_GBL_DATA_OFFSET		- Start of global data, top of stack
+ */
+
+#define CFG_INIT_RAM_ADDR		(CFG_SDRAM_BASE + 0x4000)
+#define CFG_INIT_RAM_END		0x4000
+#define CFG_GBL_DATA_SIZE		128
+#define CFG_GBL_DATA_OFFSET		(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+
+/*
+ * Initial BAT config
+ * 
+ * BAT0	- System SDRAM
+ * BAT1 - LED's and Serial Port
+ * BAT2 - PCI Memory
+ * BAT3 - PCI I/O including Flash Memory
+ */
+
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+
+#define CFG_IBAT1L (0x70000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT1U (0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L (0x70000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT1U (0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT2L (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT2L (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT3L (0xF0000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT3L (0xF0000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+
+/*
+ * Cache config
+ * 
+ * CFG_CACHELINE_SIZE		- Size of a cache line (CPU specific)
+ * CFG_L2					- L2 cache enabled if defined
+ * L2_INIT					- L2 cache init flags
+ * L2_ENABLE				- L2 cache enable flags
+ */
+
+#define CFG_CACHELINE_SIZE		32
+#undef	CFG_L2
+#define L2_INIT					0
+#define L2_ENABLE				0
+
+
+/*
+ * Clocks config
+ * 
+ * CFG_BUS_HZ				- Bus clock frequency in Hz
+ * CFG_BUS_CLK				- As above (?)
+ * CFG_HZ					- Decrementer freq in Hz
+ */
+
+#define CFG_BUS_HZ				CONFIG_BUS_CLK
+#define CFG_BUS_CLK				CONFIG_BUS_CLK
+#define CFG_HZ					1000
+
+
+/*
+ * Serial port config
+ * 
+ * CFG_BAUDRATE_TABLE		- List of valid baud rates
+ * CFG_NS16550				- Include the NS16550 driver
+ * CFG_NS16550_SERIAL		- Include the serial (wrapper) driver
+ * CFG_NS16550_CLK			- Frequency of reference clock
+ * CFG_NS16550_REG_SIZE		- 64-bit accesses to 8-bit port
+ * CFG_NS16550_COM1			- Base address of 1st serial port
+ */
+
+#define CFG_BAUDRATE_TABLE		{ 9600, 19200, 38400, 57600, 115200 }
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_CLK			3686400
+#define CFG_NS16550_REG_SIZE	-8
+#define CFG_NS16550_COM1		0x7C000000
+
+
+/*
+ * PCI Config - Address Map B (CHRP)
+ */
+
+#define CFG_PCI_MEMORY_BUS      0x00000000
+#define CFG_PCI_MEMORY_PHYS     0x00000000
+#define CFG_PCI_MEMORY_SIZE     0x40000000
+#define CFG_PCI_MEM_BUS         0x80000000
+#define CFG_PCI_MEM_PHYS        0x80000000
+#define CFG_PCI_MEM_SIZE        0x7D000000
+#define CFG_ISA_MEM_BUS         0x00000000
+#define CFG_ISA_MEM_PHYS        0xFD000000
+#define CFG_ISA_MEM_SIZE        0x01000000
+#define CFG_PCI_IO_BUS          0x00800000
+#define CFG_PCI_IO_PHYS         0xFE800000
+#define CFG_PCI_IO_SIZE         0x00400000
+#define CFG_ISA_IO_BUS          0x00000000
+#define CFG_ISA_IO_PHYS         0xFE000000
+#define CFG_ISA_IO_SIZE         0x00800000
+#define CFG_ISA_IO_BASE_ADDRESS CFG_ISA_IO_PHYS
+#define CFG_ISA_IO              CFG_ISA_IO_PHYS
+#define CFG_60X_PCI_IO_OFFSET   CFG_ISA_IO_PHYS
+
+
+/*
+ * Extra init functions
+ * 
+ * CFG_BOARD_ASM_INIT		- Call assembly init code
+ */
+
+#define CFG_BOARD_ASM_INIT
+
+
+/*
+ * Boot flags
+ * 
+ * BOOTFLAG_COLD			- Indicates a power-on boot
+ * BOOTFLAG_WARM			- Indicates a software reset
+ */
+ 
+#define BOOTFLAG_COLD			0x01
+#define BOOTFLAG_WARM			0x02
+
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/spieval.h b/include/configs/spieval.h
index 96cb6e4..9ebb51e 100644
--- a/include/configs/spieval.h
+++ b/include/configs/spieval.h
@@ -191,16 +191,6 @@
 
 #undef	CONFIG_BOOTARGS
 
-#if defined (CONFIG_TQM5200_AA)
-# define CONFIG_U_BOOT_SUFFIX	"-AA\0"
-#elif defined (CONFIG_TQM5200_AB)
-# define CONFIG_U_BOOT_SUFFIX	"-AB\0"
-#elif defined (CONFIG_TQM5200_AC)
-# define CONFIG_U_BOOT_SUFFIX	"-AC\0"
-#else
-# define CONFIG_U_BOOT_SUFFIX	"\0"
-#endif
-
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"rootpath=/opt/eldk/ppc_6xx\0"					\
@@ -217,7 +207,7 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"bootfile=/tftpboot/tqm5200/uImage\0"				\
 	"load=tftp 200000 ${u-boot}\0"					\
-	"u-boot=/tftpboot/tqm5200/u-boot.bin"	CONFIG_U_BOOT_SUFFIX	\
+	"u-boot=/tftpboot/tqm5200/u-boot.bin\0"				\
 	"update=protect off FC000000 FC05FFFF;"				\
 		"erase FC000000 FC05FFFF;"				\
 		"cp.b 200000 FC000000 ${filesize};"			\
@@ -283,13 +273,6 @@
 #endif
 
 /* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AB)
-#define I2C_ADDR_LIST	{	CFG_I2C_EEPROM_ADDR,	\
-				CFG_I2C_SLAVE }
-#elif defined (CONFIG_TQM5200_AC)
-#define I2C_ADDR_LIST	{	CFG_I2C_SLAVE }
-#endif
-
 #if defined (CONFIG_MINIFAP)
 #undef I2C_ADDR_LIST
 #define I2C_ADDR_LIST	{	CFG_I2C_EEPROM_ADDR,	\
@@ -478,13 +461,9 @@
  * SRAM - Do not map below 2 GB in address space, because this area is used
  * for SDRAM autosizing.
  */
-#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
 #define CFG_CS2_START		0xE5000000
-#ifdef CONFIG_TQM5200_AB
-#define CFG_CS2_SIZE		0x80000		/* 512 kByte */
-#else  /* CONFIG_CS_AUTOCONF */
 #define CFG_CS2_SIZE		0x100000	/* 1 MByte */
-#endif
 #define CFG_CS2_CFG		0x0004D930
 #endif
 
@@ -492,8 +471,7 @@
  * Grafic controller - Do not map below 2 GB in address space, because this
  * area is used for SDRAM autosizing.
  */
-#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \
-    defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
 #define SM501_FB_BASE		0xE0000000
 #define CFG_CS1_START		(SM501_FB_BASE)
 #define CFG_CS1_SIZE		0x4000000	/* 64 MByte */
diff --git a/include/configs/trab.h b/include/configs/trab.h
index b6d4bcf..935aca2d 100644
--- a/include/configs/trab.h
+++ b/include/configs/trab.h
@@ -165,7 +165,6 @@
 				CFG_CMD_DATE			| \
 				CFG_CMD_DHCP			| \
 				CFG_CMD_FAT			| \
-				CFG_CMD_JFFS2			| \
 				CFG_CMD_NFS			| \
 				CFG_CMD_SNTP			| \
 				CFG_CMD_USB	)
@@ -179,7 +178,6 @@
 				CFG_CMD_DATE			| \
 				CFG_CMD_DHCP			| \
 				CFG_CMD_FAT			| \
-				CFG_CMD_JFFS2			| \
 				CFG_CMD_NFS			| \
 				CFG_CMD_SNTP			| \
 				CFG_CMD_USB	)
@@ -389,10 +387,10 @@
 #define MTDIDS_DEFAULT		"nor0=0"
 
 /* production flash layout */
-#define MTDPARTS_DEFAULT	"mtdparts=0:32k(Firmware1)ro,"		\
+#define MTDPARTS_DEFAULT	"mtdparts=0:16k(Firmware1)ro,"		\
 						"16k(Env1),"		\
 						"16k(Env2),"		\
-						"320k(Firmware2)ro,"	\
+						"336k(Firmware2)ro,"	\
 						"896k(Kernel),"		\
 						"5376k(Root-FS),"	\
 						"1408k(JFFS2),"		\
diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h
index c5ee78f..4e97b01 100644
--- a/include/configs/voiceblue.h
+++ b/include/configs/voiceblue.h
@@ -47,6 +47,8 @@
 #define CONFIG_SETUP_MEMORY_TAGS	1
 #define CONFIG_INITRD_TAG		1
 
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
 /*
  * Physical Memory Map
  */
@@ -94,7 +96,6 @@
 
 #define CONFIG_ENV_OVERWRITE
 
-#define CFG_JFFS_CUSTOM_PART	/* see board/voiceblue/jffs2parts.c */
 #endif
 
 /*
@@ -104,9 +105,11 @@
 #ifdef VOICEBLUE_SMALL_FLASH
 #define CFG_MALLOC_LEN		(SZ_64K - CFG_GBL_DATA_SIZE)
 #define CONFIG_STACKSIZE	SZ_8K
+#define PHYS_SDRAM_1_RESERVED	0
 #else
 #define CFG_MALLOC_LEN		SZ_4M
 #define CONFIG_STACKSIZE	SZ_1M
+#define PHYS_SDRAM_1_RESERVED	(CFG_MONITOR_LEN + CFG_MALLOC_LEN + CONFIG_STACKSIZE)
 #endif
 
 /*
@@ -174,6 +177,7 @@
 #define CONFIG_BOOTCOMMAND	"run nboot"
 #define CONFIG_PREBOOT		"run setup"
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"silent=1\0"						\
 	"ospart=0\0"						\
 	"swapos=no\0"						\
 	"setpart="						\
@@ -185,15 +189,37 @@
 	"fi\0"							\
 	"setup=setenv bootargs console=ttyS0,$baudrate "	\
 		"mtdparts=$mtdparts\0"				\
-	"nfsargs=run setpart; setenv bootargs $bootargs "	\
-		"root=/dev/nfs ip=dhcp\0"			\
+	"nfsargs=setenv bootargs $bootargs "			\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
+		"nfsroot=$rootpath root=/dev/nfs\0"		\
 	"flashargs=run setpart; setenv bootargs $bootargs "	\
 		"root=/dev/mtdblock$partition ro "		\
 		"rootfstype=jffs2\0"				\
-	"nboot=run nfsargs; bootp; tftp; bootm\0"		\
-	"fboot=run flashargs; fsload /boot/uImage; bootm\0"
+	"initrdargs=setenv bootargs $bootargs "			\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
+	"fboot=run flashargs; fsload /boot/uImage; bootm\0"	\
+	"iboot=bootp; run initrdargs; tftp; bootm\0"		\
+	"nboot=bootp; run nfsargs; tftp; bootm\0"
 #endif
 
+#ifndef VOICEBLUE_SMALL_FLASH
+#define CONFIG_SILENT_CONSOLE		1	/* enable silent startup */
+
+#if 1	/* feel free to disable for development */
+#define CONFIG_AUTOBOOT_KEYED		/* Enable password protection	*/
+#define CONFIG_AUTOBOOT_PROMPT	"\nVoiceBlue Enterprise - booting...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"."	/* 1st "password"	*/
+#endif
+
+/*
+ * JFFS2 partitions (mtdparts command line support)
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=omapflash.0"
+#define MTDPARTS_DEFAULT	"mtdparts=omapflash.0:128k(uboot),64k(env),64k(r_env),16256k(data1),-(data2)"
+
+#endif	/* VOICEBLUE_SMALL_FLASH */
+
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
@@ -213,7 +239,7 @@
 #define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
 #define CFG_MEMTEST_START	PHYS_SDRAM_1
-#define CFG_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE
+#define CFG_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
 
 #undef	CFG_CLKS_IN_HZ		/* everything, incl board info, in Hz */
 
@@ -247,22 +273,4 @@
 
 #define VOICEBLUE_LED_REG	0x04030000
 
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00040000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT		"nor0=voiceblue-0"
-#define MTDPARTS_DEFAULT	"mtdparts=voiceblue-0:128k(uboot),64k(env),64k(renv),-(jffs2)"
-*/
-
 #endif	/* __CONFIG_H */
diff --git a/include/ns16550.h b/include/ns16550.h
index d987a8b..996d915 100644
--- a/include/ns16550.h
+++ b/include/ns16550.h
@@ -7,6 +7,9 @@
  * added prototypes for ns16550.c
  * reduced no of com ports to 2
  * modifications (c) Rob Taylor, Flying Pig Systems. 2000.
+ * 
+ * added support for port on 64-bit bus
+ * by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems
  */
 
 #if (CFG_NS16550_REG_SIZE == 1)
@@ -82,6 +85,25 @@ struct NS16550 {
 	int pad10:24;
 #endif
 } __attribute__ ((packed));
+#elif (CFG_NS16550_REG_SIZE == -8)
+struct NS16550 {
+	unsigned char rbr;		/* 0 */
+	unsigned char pad0[7];
+	unsigned char ier;		/* 1 */
+	unsigned char pad1[7];
+	unsigned char fcr;		/* 2 */
+	unsigned char pad2[7];
+	unsigned char lcr;		/* 3 */
+	unsigned char pad3[7];
+	unsigned char mcr;		/* 4 */
+	unsigned char pad4[7];
+	unsigned char lsr;		/* 5 */
+	unsigned char pad5[7];
+	unsigned char msr;		/* 6 */
+	unsigned char pad6[7];
+	unsigned char scr;		/* 7 */
+	unsigned char pad7[7];
+} __attribute__ ((packed));
 #else
 #error "Please define NS16550 registers size."
 #endif
diff --git a/include/serial.h b/include/serial.h
index c8abb72..8c7b1c2 100644
--- a/include/serial.h
+++ b/include/serial.h
@@ -23,7 +23,7 @@ extern struct serial_device serial_scc_device;
 extern struct serial_device * default_serial_console (void);
 
 #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
-   || defined(CONFIG_405EP)
+   || defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
 extern struct serial_device serial0_device;
 extern struct serial_device serial1_device;
 #endif