armv8: ls1046aqds: Add LS1046AQDS board support

LS1046AQDS Specification:
-------------------------
Memory subsystem:
 * 8GByte DDR4 SDRAM (64bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 64 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * Two XFI 10G ports
 * Two SGMII ports
 * Two RGMII ports

PCIe: supports Gen 1 and Gen 2

SATA 3.0: one SATA 3.0 port

USB 3.0: two micro AB connector and one type A connector

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

25 files changed, 1866 insertions, 5 deletions

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 215efdc..1560bcc 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -841,6 +841,18 @@ config TARGET_LS1043ARDB
 	help
 	  Support for Freescale LS1043ARDB platform.
 
+config TARGET_LS1046AQDS
+	bool "Support ls1046aqds"
+	select ARM64
+	select ARMV8_MULTIENTRY
+	select SUPPORT_SPL
+	select DM_SPI_FLASH if DM_SPI
+	help
+	  Support for Freescale LS1046AQDS platform.
+	  The LS1046A Development System (QDS) is a high-performance
+	  development platform that supports the QorIQ LS1046A
+	  Layerscape Architecture processor.
+
 config TARGET_LS1046ARDB
 	bool "Support ls1046ardb"
 	select ARM64
@@ -996,6 +1008,7 @@ source "board/freescale/ls2080ardb/Kconfig"
 source "board/freescale/ls1021aqds/Kconfig"
 source "board/freescale/ls1043aqds/Kconfig"
 source "board/freescale/ls1021atwr/Kconfig"
+source "board/freescale/ls1046aqds/Kconfig"
 source "board/freescale/ls1043ardb/Kconfig"
 source "board/freescale/ls1046ardb/Kconfig"
 source "board/freescale/ls1012aqds/Kconfig"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index a15ca53..715e9bd 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -143,6 +143,7 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
 dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
 	fsl-ls1043a-qds-lpuart.dtb \
 	fsl-ls1043a-rdb.dtb \
+	fsl-ls1046a-qds-duart.dtb \
 	fsl-ls1046a-rdb.dtb \
 	fsl-ls1012a-qds.dtb \
 	fsl-ls1012a-rdb.dtb \
diff --git a/arch/arm/dts/fsl-ls1046a-qds-duart.dts b/arch/arm/dts/fsl-ls1046a-qds-duart.dts
new file mode 100644
index 0000000..10a95ea
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1046a-qds-duart.dts
@@ -0,0 +1,16 @@
+/*
+ * Device Tree file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright (C) 2016, Freescale Semiconductor
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/dts-v1/;
+#include "fsl-ls1046a-qds.dtsi"
+
+/ {
+       chosen {
+               stdout-path = &duart0;
+       };
+};
diff --git a/arch/arm/dts/fsl-ls1046a-qds.dtsi b/arch/arm/dts/fsl-ls1046a-qds.dtsi
new file mode 100644
index 0000000..c512293
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1046a-qds.dtsi
@@ -0,0 +1,77 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright (C) 2016, Freescale Semiconductor
+ *
+ * Mingkai Hu <Mingkai.hu@nxp.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/include/ "fsl-ls1046a.dtsi"
+
+/ {
+	model = "LS1046A QDS Board";
+	aliases {
+		spi0 = &qspi;
+		spi1 = &dspi0;
+	};
+};
+
+&dspi0 {
+	bus-num = <0>;
+	status = "okay";
+
+	dflash0: n25q128a {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <1000000>; /* input clock */
+		spi-cpol;
+		spi-cpha;
+		reg = <0>;
+	};
+
+	dflash1: sst25wf040b {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <3500000>;
+		spi-cpol;
+		spi-cpha;
+		reg = <1>;
+	};
+
+	dflash2: en25s64 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <3500000>;
+		spi-cpol;
+		spi-cpha;
+		reg = <2>;
+	};
+};
+
+&qspi {
+	bus-num = <0>;
+	status = "okay";
+
+	qflash0: s25fl128s@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&duart1 {
+	status = "okay";
+};
diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c
index 2f29795..1a50304 100644
--- a/board/freescale/common/vid.c
+++ b/board/freescale/common/vid.c
@@ -8,7 +8,7 @@
 #include <command.h>
 #include <i2c.h>
 #include <asm/io.h>
-#ifdef CONFIG_LS1043A
+#ifdef CONFIG_FSL_LSCH2
 #include <asm/arch/immap_lsch2.h>
 #elif defined(CONFIG_FSL_LSCH3)
 #include <asm/arch/immap_lsch3.h>
@@ -247,7 +247,7 @@ static int set_voltage_to_IR(int i2caddress, int vdd)
 	 * SoC before converting into an IR VID value
 	 */
 	vdd += board_vdd_drop_compensation();
-#ifdef CONFIG_LS1043A
+#ifdef CONFIG_FSL_LSCH2
 	vid = DIV_ROUND_UP(vdd - 265, 5);
 #else
 	vid = DIV_ROUND_UP(vdd - 245, 5);
@@ -287,7 +287,7 @@ static int set_voltage(int i2caddress, int vdd)
 int adjust_vdd(ulong vdd_override)
 {
 	int re_enable = disable_interrupts();
-#if defined(CONFIG_LS1043A) || defined(CONFIG_FSL_LSCH3)
+#if defined(CONFIG_FSL_LSCH2) || defined(CONFIG_FSL_LSCH3)
 	struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
 #else
 	ccsr_gur_t __iomem *gur =
@@ -386,7 +386,7 @@ int adjust_vdd(ulong vdd_override)
 	 * | T |          |         |                 |         |
 	 * ------------------------------------------------------
 	 */
-#ifdef CONFIG_LS1043A
+#ifdef CONFIG_FSL_LSCH2
 	vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_ALTVID_SHIFT) &
 		FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK;
 	if ((vid == 0) || (vid == FSL_CHASSIS2_DCFG_FUSESR_ALTVID_MASK)) {
diff --git a/board/freescale/ls1046aqds/Kconfig b/board/freescale/ls1046aqds/Kconfig
new file mode 100644
index 0000000..723f4ba
--- /dev/null
+++ b/board/freescale/ls1046aqds/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_LS1046AQDS
+
+config SYS_BOARD
+	default "ls1046aqds"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_SOC
+	default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+	default "ls1046aqds"
+
+endif
diff --git a/board/freescale/ls1046aqds/MAINTAINERS b/board/freescale/ls1046aqds/MAINTAINERS
new file mode 100644
index 0000000..b4549ae
--- /dev/null
+++ b/board/freescale/ls1046aqds/MAINTAINERS
@@ -0,0 +1,10 @@
+LS1046AQDS BOARD
+M:	Mingkai Hu <Mingkai.Hu@nxp.com>
+S:	Maintained
+F:	board/freescale/ls1046aqds/
+F:	include/configs/ls1046aqds.h
+F:	configs/ls1046aqds_defconfig
+F:	configs/ls1046aqds_nand_defconfig
+F:	configs/ls1046aqds_sdcard_ifc_defconfig
+F:	configs/ls1046aqds_sdcard_qspi_defconfig
+F:	configs/ls1046aqds_qspi_defconfig
diff --git a/board/freescale/ls1046aqds/Makefile b/board/freescale/ls1046aqds/Makefile
new file mode 100644
index 0000000..df6e546
--- /dev/null
+++ b/board/freescale/ls1046aqds/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright 2016 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:      GPL-2.0+
+#
+
+obj-y += ddr.o
+obj-y += eth.o
+obj-y += ls1046aqds.o
diff --git a/board/freescale/ls1046aqds/README b/board/freescale/ls1046aqds/README
new file mode 100644
index 0000000..b8fa326
--- /dev/null
+++ b/board/freescale/ls1046aqds/README
@@ -0,0 +1,70 @@
+Overview
+--------
+The LS1046A Development System (QDS) is a high-performance computing,
+evaluation, and development platform that supports the QorIQ LS1046A
+LayerScape Architecture processor. The LS1046AQDS provides SW development
+platform for the Freescale LS1046A processor series, with a complete
+debugging environment.
+
+LS1046A SoC Overview
+--------------------
+Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS1046A
+SoC overview.
+
+ LS1046AQDS board Overview
+ -----------------------
+ - SERDES Connections, 8 lanes supporting:
+      - PCI Express - 3.0
+      - SGMII, SGMII 2.5
+      - QSGMII
+      - SATA 3.0
+      - XFI
+ - DDR Controller
+     - 8GB 64bits DDR4 SDRAM. Support rates of up to 2133MT/s
+ -IFC/Local Bus
+    - One in-socket 128 MB NOR flash 16-bit data bus
+    - One 512 MB NAND flash with ECC support
+    - PromJet Port
+    - FPGA connection
+ - USB 3.0
+    - Three high speed USB 3.0 ports
+    - First USB 3.0 port configured as Host with Type-A connector
+    - The other two USB 3.0 ports configured as OTG with micro-AB connector
+ - SDHC port connects directly to an adapter card slot, featuring:
+    - Optional clock feedback paths, and optional high-speed voltage translation assistance
+    - SD slots for SD, SDHC (1x, 4x, 8x), and/or MMC
+    - eMMC memory devices
+ - DSPI: Onboard support for three SPI flash memory devices
+ - 4 I2C controllers
+ - One SATA onboard connectors
+ - UART
+   - Two 4-pin serial ports at up to 115.2 Kbit/s
+   - Two DB9 D-Type connectors supporting one Serial port each
+ - ARM JTAG support
+
+Memory map from core's view
+----------------------------
+Start Address    End Address     Description		Size
+0x00_0000_0000 - 0x00_000F_FFFF  Secure Boot ROM	1MB
+0x00_0100_0000 - 0x00_0FFF_FFFF  CCSRBAR		240MB
+0x00_1000_0000 - 0x00_1000_FFFF  OCRAM0 		64KB
+0x00_1001_0000 - 0x00_1001_FFFF  OCRAM1 		64KB
+0x00_2000_0000 - 0x00_20FF_FFFF  DCSR			16MB
+0x00_6000_0000 - 0x00_67FF_FFFF  IFC - NOR Flash	128MB
+0x00_7E80_0000 - 0x00_7E80_FFFF  IFC - NAND Flash	64KB
+0x00_7FB0_0000 - 0x00_7FB0_0FFF  IFC - FPGA		4KB
+0x00_8000_0000 - 0x00_FFFF_FFFF  DRAM1			2GB
+0x05_0000_0000 - 0x05_07FF_FFFF  QMAN S/W Portal	128M
+0x05_0800_0000 - 0x05_0FFF_FFFF  BMAN S/W Portal	128M
+0x08_8000_0000 - 0x09_FFFF_FFFF  DRAM2			6GB
+0x40_0000_0000 - 0x47_FFFF_FFFF  PCI Express1		32G
+0x48_0000_0000 - 0x4F_FFFF_FFFF  PCI Express2		32G
+0x50_0000_0000 - 0x57_FFFF_FFFF  PCI Express3		32G
+
+Booting Options
+---------------
+a) Promjet Boot
+b) NOR boot
+c) NAND boot
+d) SD boot
+e) QSPI boot
diff --git a/board/freescale/ls1046aqds/ddr.c b/board/freescale/ls1046aqds/ddr.c
new file mode 100644
index 0000000..d813965
--- /dev/null
+++ b/board/freescale/ls1046aqds/ddr.c
@@ -0,0 +1,140 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#ifdef CONFIG_FSL_DEEP_SLEEP
+#include <fsl_sleep.h>
+#endif
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+			   dimm_params_t *pdimm,
+			   unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num > 3) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	pbsp = udimms[0];
+
+	/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found for %lu MT/s\n",
+		       ddr_freq);
+		printf("Trying to use the highest speed (%u) parameters\n",
+		       pbsp_highest->datarate_mhz_high);
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+found:
+	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+	      pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+
+	popts->data_bus_width = 0;      /* 64b data bus */
+	popts->otf_burst_chop_en = 0;
+	popts->burst_length = DDR_BL8;
+	popts->bstopre = 0;		/* enable auto precharge */
+
+	popts->half_strength_driver_enable = 0;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+			  DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
+	return fsl_ddr_sdram_size();
+#else
+	puts("Initializing DDR....using SPD\n");
+
+	dram_size = fsl_ddr_sdram();
+#endif
+
+#ifdef CONFIG_FSL_DEEP_SLEEP
+	fsl_dp_ddr_restore();
+#endif
+
+	erratum_a008850_post();
+
+	return dram_size;
+}
+
+void dram_init_banksize(void)
+{
+	/*
+	 * gd->arch.secure_ram tracks the location of secure memory.
+	 * It was set as if the memory starts from 0.
+	 * The address needs to add the offset of its bank.
+	 */
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
+		gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
+		gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
+		gd->bd->bi_dram[1].size = gd->ram_size -
+					  CONFIG_SYS_DDR_BLOCK1_SIZE;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->arch.secure_ram = gd->bd->bi_dram[1].start +
+				 gd->arch.secure_ram -
+				 CONFIG_SYS_DDR_BLOCK1_SIZE;
+		gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
+	} else {
+		gd->bd->bi_dram[0].size = gd->ram_size;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->arch.secure_ram = gd->bd->bi_dram[0].start +
+				 gd->arch.secure_ram;
+		gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
+	}
+}
diff --git a/board/freescale/ls1046aqds/ddr.h b/board/freescale/ls1046aqds/ddr.h
new file mode 100644
index 0000000..b594032
--- /dev/null
+++ b/board/freescale/ls1046aqds/ddr.h
@@ -0,0 +1,44 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+
+void erratum_a008850_post(void);
+
+struct board_specific_parameters {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 rank_gb;
+	u32 clk_adjust;
+	u32 wrlvl_start;
+	u32 wrlvl_ctl_2;
+	u32 wrlvl_ctl_3;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_parameters udimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl |
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |
+	 */
+	{2,  1350, 0, 8,     6, 0x0708090B, 0x0C0D0E09,},
+	{2,  1666, 0, 8,     7, 0x08090A0C, 0x0D0F100B,},
+	{2,  1900, 0, 8,     7, 0x09090B0D, 0x0E10120B,},
+	{2,  2300, 0, 8,     9, 0x0A0C0D11, 0x1214150E,},
+	{}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+	udimm0,
+};
+
+#endif
diff --git a/board/freescale/ls1046aqds/eth.c b/board/freescale/ls1046aqds/eth.c
new file mode 100644
index 0000000..046db11
--- /dev/null
+++ b/board/freescale/ls1046aqds/eth.c
@@ -0,0 +1,415 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <netdev.h>
+#include <fdt_support.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <fsl_dtsec.h>
+#include <malloc.h>
+#include <asm/arch/fsl_serdes.h>
+
+#include "../common/qixis.h"
+#include "../common/fman.h"
+#include "ls1046aqds_qixis.h"
+
+#define EMI_NONE	0xFF
+#define EMI1_RGMII1	0
+#define EMI1_RGMII2	1
+#define EMI1_SLOT1	2
+#define EMI1_SLOT2	3
+#define EMI1_SLOT4	4
+
+static int mdio_mux[NUM_FM_PORTS];
+
+static const char * const mdio_names[] = {
+	"LS1046AQDS_MDIO_RGMII1",
+	"LS1046AQDS_MDIO_RGMII2",
+	"LS1046AQDS_MDIO_SLOT1",
+	"LS1046AQDS_MDIO_SLOT2",
+	"LS1046AQDS_MDIO_SLOT4",
+	"NULL",
+};
+
+/* Map SerDes 1 & 2 lanes to default slot. */
+static u8 lane_to_slot[] = {1, 1, 1, 1, 0, 4, 0 , 0};
+
+static const char *ls1046aqds_mdio_name_for_muxval(u8 muxval)
+{
+	return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u8 muxval)
+{
+	struct mii_dev *bus;
+	const char *name;
+
+	if (muxval > EMI1_SLOT4)
+		return NULL;
+
+	name = ls1046aqds_mdio_name_for_muxval(muxval);
+
+	if (!name) {
+		printf("No bus for muxval %x\n", muxval);
+		return NULL;
+	}
+
+	bus = miiphy_get_dev_by_name(name);
+
+	if (!bus) {
+		printf("No bus by name %s\n", name);
+		return NULL;
+	}
+
+	return bus;
+}
+
+struct ls1046aqds_mdio {
+	u8 muxval;
+	struct mii_dev *realbus;
+};
+
+static void ls1046aqds_mux_mdio(u8 muxval)
+{
+	u8 brdcfg4;
+
+	if (muxval < 7) {
+		brdcfg4 = QIXIS_READ(brdcfg[4]);
+		brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+		brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
+		QIXIS_WRITE(brdcfg[4], brdcfg4);
+	}
+}
+
+static int ls1046aqds_mdio_read(struct mii_dev *bus, int addr, int devad,
+			      int regnum)
+{
+	struct ls1046aqds_mdio *priv = bus->priv;
+
+	ls1046aqds_mux_mdio(priv->muxval);
+
+	return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int ls1046aqds_mdio_write(struct mii_dev *bus, int addr, int devad,
+			       int regnum, u16 value)
+{
+	struct ls1046aqds_mdio *priv = bus->priv;
+
+	ls1046aqds_mux_mdio(priv->muxval);
+
+	return priv->realbus->write(priv->realbus, addr, devad,
+				    regnum, value);
+}
+
+static int ls1046aqds_mdio_reset(struct mii_dev *bus)
+{
+	struct ls1046aqds_mdio *priv = bus->priv;
+
+	return priv->realbus->reset(priv->realbus);
+}
+
+static int ls1046aqds_mdio_init(char *realbusname, u8 muxval)
+{
+	struct ls1046aqds_mdio *pmdio;
+	struct mii_dev *bus = mdio_alloc();
+
+	if (!bus) {
+		printf("Failed to allocate ls1046aqds MDIO bus\n");
+		return -1;
+	}
+
+	pmdio = malloc(sizeof(*pmdio));
+	if (!pmdio) {
+		printf("Failed to allocate ls1046aqds private data\n");
+		free(bus);
+		return -1;
+	}
+
+	bus->read = ls1046aqds_mdio_read;
+	bus->write = ls1046aqds_mdio_write;
+	bus->reset = ls1046aqds_mdio_reset;
+	sprintf(bus->name, ls1046aqds_mdio_name_for_muxval(muxval));
+
+	pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+	if (!pmdio->realbus) {
+		printf("No bus with name %s\n", realbusname);
+		free(bus);
+		free(pmdio);
+		return -1;
+	}
+
+	pmdio->muxval = muxval;
+	bus->priv = pmdio;
+	return mdio_register(bus);
+}
+
+void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
+			      enum fm_port port, int offset)
+{
+	struct fixed_link f_link;
+
+	if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
+		switch (port) {
+		case FM1_DTSEC9:
+			fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p1");
+			break;
+		case FM1_DTSEC10:
+			fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p2");
+			break;
+		case FM1_DTSEC5:
+			fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p3");
+			break;
+		case FM1_DTSEC6:
+			fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p4");
+			break;
+		case FM1_DTSEC2:
+			fdt_set_phy_handle(fdt, compat, addr, "sgmii_s4_p1");
+			break;
+		default:
+			break;
+		}
+	} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) {
+		/* 2.5G SGMII interface */
+		f_link.phy_id = cpu_to_fdt32(port);
+		f_link.duplex = cpu_to_fdt32(1);
+		f_link.link_speed = cpu_to_fdt32(1000);
+		f_link.pause = 0;
+		f_link.asym_pause = 0;
+		/* no PHY for 2.5G SGMII on QDS */
+		fdt_delprop(fdt, offset, "phy-handle");
+		fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link));
+		fdt_setprop_string(fdt, offset, "phy-connection-type",
+				   "sgmii-2500");
+	} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_QSGMII) {
+		switch (port) {
+		case FM1_DTSEC1:
+			fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p4");
+			break;
+		case FM1_DTSEC5:
+			fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p2");
+			break;
+		case FM1_DTSEC6:
+			fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p1");
+			break;
+		case FM1_DTSEC10:
+			fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p3");
+			break;
+		default:
+			break;
+		}
+		fdt_delprop(fdt, offset, "phy-connection-type");
+		fdt_setprop_string(fdt, offset, "phy-connection-type",
+				   "qsgmii");
+	} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII &&
+		   (port == FM1_10GEC1 || port == FM1_10GEC2)) {
+		/* XFI interface */
+		f_link.phy_id = cpu_to_fdt32(port);
+		f_link.duplex = cpu_to_fdt32(1);
+		f_link.link_speed = cpu_to_fdt32(10000);
+		f_link.pause = 0;
+		f_link.asym_pause = 0;
+		/* no PHY for XFI */
+		fdt_delprop(fdt, offset, "phy-handle");
+		fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link));
+		fdt_setprop_string(fdt, offset, "phy-connection-type", "xgmii");
+	}
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+	int i;
+
+	for (i = FM1_DTSEC1; i < NUM_FM_PORTS; i++) {
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_SGMII:
+		case PHY_INTERFACE_MODE_QSGMII:
+			switch (mdio_mux[i]) {
+			case EMI1_SLOT1:
+				fdt_status_okay_by_alias(fdt, "emi1_slot1");
+				break;
+			case EMI1_SLOT2:
+				fdt_status_okay_by_alias(fdt, "emi1_slot2");
+				break;
+			case EMI1_SLOT4:
+				fdt_status_okay_by_alias(fdt, "emi1_slot4");
+				break;
+			default:
+				break;
+			}
+			break;
+		default:
+			break;
+		}
+	}
+}
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_FMAN_ENET
+	int i, idx, lane, slot, interface;
+	struct memac_mdio_info dtsec_mdio_info;
+	struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+	u32 srds_s1, srds_s2;
+	u8 brdcfg12;
+
+	srds_s1 = in_be32(&gur->rcwsr[4]) &
+			FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
+	srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+	srds_s2 = in_be32(&gur->rcwsr[4]) &
+			FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK;
+	srds_s2 >>= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT;
+
+	/* Initialize the mdio_mux array so we can recognize empty elements */
+	for (i = 0; i < NUM_FM_PORTS; i++)
+		mdio_mux[i] = EMI_NONE;
+
+	dtsec_mdio_info.regs =
+		(struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+	dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+	/* Register the 1G MDIO bus */
+	fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+	/* Register the muxing front-ends to the MDIO buses */
+	ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
+	ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
+	ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
+	ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
+	ls1046aqds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
+
+	/* Set the two on-board RGMII PHY address */
+	fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
+	fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR);
+
+	switch (srds_s1) {
+	case 0x3333:
+		/* SGMII on slot 1, MAC 9 */
+		fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR);
+	case 0x1333:
+	case 0x2333:
+		/* SGMII on slot 1, MAC 10 */
+		fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+	case 0x1133:
+	case 0x2233:
+		/* SGMII on slot 1, MAC 5/6 */
+		fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR);
+		break;
+	case 0x1040:
+	case 0x2040:
+		/* QSGMII on lane B, MAC 6/5/10/1 */
+		fm_info_set_phy_address(FM1_DTSEC6,
+					QSGMII_CARD_PORT1_PHY_ADDR_S2);
+		fm_info_set_phy_address(FM1_DTSEC5,
+					QSGMII_CARD_PORT2_PHY_ADDR_S2);
+		fm_info_set_phy_address(FM1_DTSEC10,
+					QSGMII_CARD_PORT3_PHY_ADDR_S2);
+		fm_info_set_phy_address(FM1_DTSEC1,
+					QSGMII_CARD_PORT4_PHY_ADDR_S2);
+		break;
+	case 0x3363:
+		/* SGMII on slot 1, MAC 9/10 */
+		fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+	case 0x1163:
+	case 0x2263:
+	case 0x2223:
+		/* SGMII on slot 1, MAC 6 */
+		fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR);
+		break;
+	default:
+		printf("Invalid SerDes protocol 0x%x for LS1046AQDS\n",
+		       srds_s1);
+		break;
+	}
+
+	if (srds_s2 == 0x5a59 || srds_s2 == 0x5a06)
+		/* SGMII on slot 4, MAC 2 */
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+
+	for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+		idx = i - FM1_DTSEC1;
+		interface = fm_info_get_enet_if(i);
+		switch (interface) {
+		case PHY_INTERFACE_MODE_SGMII:
+		case PHY_INTERFACE_MODE_QSGMII:
+			if (interface == PHY_INTERFACE_MODE_SGMII) {
+				if (i == FM1_DTSEC5) {
+					/* route lane 2 to slot1 so to have
+					 * one sgmii riser card supports
+					 * MAC5 and MAC6.
+					 */
+					brdcfg12 = QIXIS_READ(brdcfg[12]);
+					QIXIS_WRITE(brdcfg[12],
+						    brdcfg12 | 0x80);
+				}
+				lane = serdes_get_first_lane(FSL_SRDS_1,
+						SGMII_FM1_DTSEC1 + idx);
+			} else {
+				/* clear the bit 7 to route lane B on slot2. */
+				brdcfg12 = QIXIS_READ(brdcfg[12]);
+				QIXIS_WRITE(brdcfg[12], brdcfg12 & 0x7f);
+
+				lane = serdes_get_first_lane(FSL_SRDS_1,
+						QSGMII_FM1_A);
+				lane_to_slot[lane] = 2;
+			}
+
+			if (i == FM1_DTSEC2)
+				lane = 5;
+
+			if (lane < 0)
+				break;
+
+			slot = lane_to_slot[lane];
+			debug("FM1@DTSEC%u expects SGMII in slot %u\n",
+			      idx + 1, slot);
+			if (QIXIS_READ(present2) & (1 << (slot - 1)))
+				fm_disable_port(i);
+
+			switch (slot) {
+			case 1:
+				mdio_mux[i] = EMI1_SLOT1;
+				fm_info_set_mdio(i, mii_dev_for_muxval(
+						 mdio_mux[i]));
+				break;
+			case 2:
+				mdio_mux[i] = EMI1_SLOT2;
+				fm_info_set_mdio(i, mii_dev_for_muxval(
+						 mdio_mux[i]));
+				break;
+			case 4:
+				mdio_mux[i] = EMI1_SLOT4;
+				fm_info_set_mdio(i, mii_dev_for_muxval(
+						 mdio_mux[i]));
+				break;
+			default:
+				break;
+			}
+			break;
+		case PHY_INTERFACE_MODE_RGMII:
+			if (i == FM1_DTSEC3)
+				mdio_mux[i] = EMI1_RGMII1;
+			else if (i == FM1_DTSEC4)
+				mdio_mux[i] = EMI1_RGMII2;
+			fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+			break;
+		default:
+			break;
+		}
+	}
+
+	cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+	return pci_eth_init(bis);
+}
diff --git a/board/freescale/ls1046aqds/ls1046aqds.c b/board/freescale/ls1046aqds/ls1046aqds.c
new file mode 100644
index 0000000..8c18538
--- /dev/null
+++ b/board/freescale/ls1046aqds/ls1046aqds.c
@@ -0,0 +1,298 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <fdt_support.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/fdt.h>
+#include <asm/arch/soc.h>
+#include <ahci.h>
+#include <hwconfig.h>
+#include <mmc.h>
+#include <scsi.h>
+#include <fm_eth.h>
+#include <fsl_csu.h>
+#include <fsl_esdhc.h>
+#include <fsl_ifc.h>
+#include <spl.h>
+
+#include "../common/vid.h"
+#include "../common/qixis.h"
+#include "ls1046aqds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+enum {
+	MUX_TYPE_GPIO,
+};
+
+int checkboard(void)
+{
+	char buf[64];
+#ifndef CONFIG_SD_BOOT
+	u8 sw;
+#endif
+
+	puts("Board: LS1046AQDS, boot from ");
+
+#ifdef CONFIG_SD_BOOT
+	puts("SD\n");
+#else
+	sw = QIXIS_READ(brdcfg[0]);
+	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+	if (sw < 0x8)
+		printf("vBank: %d\n", sw);
+	else if (sw == 0x8)
+		puts("PromJet\n");
+	else if (sw == 0x9)
+		puts("NAND\n");
+	else if (sw == 0xF)
+		printf("QSPI\n");
+	else
+		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+#endif
+
+	printf("Sys ID: 0x%02x, Sys Ver: 0x%02x\n",
+	       QIXIS_READ(id), QIXIS_READ(arch));
+
+	printf("FPGA:  v%d (%s), build %d\n",
+	       (int)QIXIS_READ(scver), qixis_read_tag(buf),
+	       (int)qixis_read_minor());
+
+	return 0;
+}
+
+bool if_board_diff_clk(void)
+{
+	u8 diff_conf = QIXIS_READ(brdcfg[11]);
+
+	return diff_conf & 0x40;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+	switch (sysclk_conf & 0x0f) {
+	case QIXIS_SYSCLK_64:
+		return 64000000;
+	case QIXIS_SYSCLK_83:
+		return 83333333;
+	case QIXIS_SYSCLK_100:
+		return 100000000;
+	case QIXIS_SYSCLK_125:
+		return 125000000;
+	case QIXIS_SYSCLK_133:
+		return 133333333;
+	case QIXIS_SYSCLK_150:
+		return 150000000;
+	case QIXIS_SYSCLK_160:
+		return 160000000;
+	case QIXIS_SYSCLK_166:
+		return 166666666;
+	}
+
+	return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+	if (if_board_diff_clk())
+		return get_board_sys_clk();
+	switch ((ddrclk_conf & 0x30) >> 4) {
+	case QIXIS_DDRCLK_100:
+		return 100000000;
+	case QIXIS_DDRCLK_125:
+		return 125000000;
+	case QIXIS_DDRCLK_133:
+		return 133333333;
+	}
+
+	return 66666666;
+}
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+	int ret;
+
+	ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+	if (ret) {
+		puts("PCA: failed to select proper channel\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	/*
+	 * When resuming from deep sleep, the I2C channel may not be
+	 * in the default channel. So, switch to the default channel
+	 * before accessing DDR SPD.
+	 */
+	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+	gd->ram_size = initdram(0);
+
+	return 0;
+}
+
+int i2c_multiplexer_select_vid_channel(u8 channel)
+{
+	return select_i2c_ch_pca9547(channel);
+}
+
+int board_early_init_f(void)
+{
+#ifdef CONFIG_HAS_FSL_XHCI_USB
+	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+	u32 usb_pwrfault;
+#endif
+
+#ifdef CONFIG_SYS_I2C_EARLY_INIT
+	i2c_early_init_f();
+#endif
+	fsl_lsch2_early_init_f();
+
+#ifdef CONFIG_HAS_FSL_XHCI_USB
+	out_be32(&scfg->rcwpmuxcr0, 0x3333);
+	out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1);
+	usb_pwrfault = (SCFG_USBPWRFAULT_DEDICATED <<
+			SCFG_USBPWRFAULT_USB3_SHIFT) |
+			(SCFG_USBPWRFAULT_DEDICATED <<
+			SCFG_USBPWRFAULT_USB2_SHIFT) |
+			(SCFG_USBPWRFAULT_SHARED <<
+			SCFG_USBPWRFAULT_USB1_SHIFT);
+	out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_FSL_DEEP_SLEEP
+/* determine if it is a warm boot */
+bool is_warm_boot(void)
+{
+#define DCFG_CCSR_CRSTSR_WDRFR	(1 << 3)
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+
+	if (in_be32(&gur->crstsr) & DCFG_CCSR_CRSTSR_WDRFR)
+		return 1;
+
+	return 0;
+}
+#endif
+
+int config_board_mux(int ctrl_type)
+{
+	u8 reg14;
+
+	reg14 = QIXIS_READ(brdcfg[14]);
+
+	switch (ctrl_type) {
+	case MUX_TYPE_GPIO:
+		reg14 = (reg14 & (~0x6)) | 0x2;
+		break;
+	default:
+		puts("Unsupported mux interface type\n");
+		return -1;
+	}
+
+	QIXIS_WRITE(brdcfg[14], reg14);
+
+	return 0;
+}
+
+int config_serdes_mux(void)
+{
+	return 0;
+}
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+	if (hwconfig("gpio"))
+		config_board_mux(MUX_TYPE_GPIO);
+
+	return 0;
+}
+#endif
+
+int board_init(void)
+{
+	select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+
+#ifdef CONFIG_SYS_FSL_SERDES
+	config_serdes_mux();
+#endif
+
+#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
+	enable_layerscape_ns_access();
+#endif
+
+	if (adjust_vdd(0))
+		printf("Warning: Adjusting core voltage failed.\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	u64 base[CONFIG_NR_DRAM_BANKS];
+	u64 size[CONFIG_NR_DRAM_BANKS];
+	u8 reg;
+
+	/* fixup DT for the two DDR banks */
+	base[0] = gd->bd->bi_dram[0].start;
+	size[0] = gd->bd->bi_dram[0].size;
+	base[1] = gd->bd->bi_dram[1].start;
+	size[1] = gd->bd->bi_dram[1].size;
+
+	fdt_fixup_memory_banks(blob, base, size, 2);
+	ft_cpu_setup(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+	fdt_fixup_fman_ethernet(blob);
+	fdt_fixup_board_enet(blob);
+#endif
+
+	reg = QIXIS_READ(brdcfg[0]);
+	reg = (reg & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+	/* Disable IFC if QSPI is enabled */
+	if (reg == 0xF)
+		do_fixup_by_compat(blob, "fsl,ifc",
+				   "status", "disabled", 8 + 1, 1);
+
+	return 0;
+}
+#endif
+
+u8 flash_read8(void *addr)
+{
+	return __raw_readb(addr + 1);
+}
+
+void flash_write16(u16 val, void *addr)
+{
+	u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00));
+
+	__raw_writew(shftval, addr);
+}
+
+u16 flash_read16(void *addr)
+{
+	u16 val = __raw_readw(addr);
+
+	return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
+}
diff --git a/board/freescale/ls1046aqds/ls1046aqds_pbi.cfg b/board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
new file mode 100644
index 0000000..5a6b7b8
--- /dev/null
+++ b/board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
@@ -0,0 +1,17 @@
+#Configure Scratch register
+09570600 00000000
+09570604 10000000
+#Alt base register
+09570158 00001000
+#Disable CCI barrier tranaction
+09570178 0000e010
+09180000 00000008
+#USB PHY frequency sel
+09570418 0000009e
+0957041c 0000009e
+09570420 0000009e
+#Serdes SATA
+09eb1300 80104e20
+09eb08dc 00502880
+#flush PBI data
+096100c0 000fffff
diff --git a/board/freescale/ls1046aqds/ls1046aqds_qixis.h b/board/freescale/ls1046aqds/ls1046aqds_qixis.h
new file mode 100644
index 0000000..58ab132
--- /dev/null
+++ b/board/freescale/ls1046aqds/ls1046aqds_qixis.h
@@ -0,0 +1,39 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __LS1046AQDS_QIXIS_H__
+#define __LS1046AQDS_QIXIS_H__
+
+/* Definitions of QIXIS Registers for LS1046AQDS */
+
+/* BRDCFG4[4:7] select EC1 and EC2 as a pair */
+#define BRDCFG4_EMISEL_MASK		0xe0
+#define BRDCFG4_EMISEL_SHIFT		5
+
+/* SYSCLK */
+#define QIXIS_SYSCLK_66			0x0
+#define QIXIS_SYSCLK_83			0x1
+#define QIXIS_SYSCLK_100		0x2
+#define QIXIS_SYSCLK_125		0x3
+#define QIXIS_SYSCLK_133		0x4
+#define QIXIS_SYSCLK_150		0x5
+#define QIXIS_SYSCLK_160		0x6
+#define QIXIS_SYSCLK_166		0x7
+#define QIXIS_SYSCLK_64			0x8
+
+/* DDRCLK */
+#define QIXIS_DDRCLK_66			0x0
+#define QIXIS_DDRCLK_100		0x1
+#define QIXIS_DDRCLK_125		0x2
+#define QIXIS_DDRCLK_133		0x3
+
+/* BRDCFG2 - SD clock*/
+#define QIXIS_SDCLK1_100		0x0
+#define QIXIS_SDCLK1_125		0x1
+#define QIXIS_SDCLK1_165		0x2
+#define QIXIS_SDCLK1_100_SP		0x3
+
+#endif
diff --git a/board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg b/board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
new file mode 100644
index 0000000..b5fc08c
--- /dev/null
+++ b/board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+# serdes protocol
+0c150010 0e000000 00000000 00000000
+11335559 40005012 e0116000 c1000000
+00000000 00000000 00000000 00038800
+00000000 01001101 00000096 00000001
diff --git a/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg b/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
new file mode 100644
index 0000000..59d24d6
--- /dev/null
+++ b/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
@@ -0,0 +1,8 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+# RCW
+# Enable IFC; disable QSPI
+0c150010 0e000000 00000000 00000000
+11335559 40005012 60040000 c1000000
+00000000 00000000 00000000 00038800
+00000000 01001101 00000096 00000001
diff --git a/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg b/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
new file mode 100644
index 0000000..9401a6f
--- /dev/null
+++ b/board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
@@ -0,0 +1,8 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+# RCW
+# Enable QSPI; disable IFC
+0c150010 0e000000 00000000 00000000
+11335559 40005012 60040000 c1000000
+00000000 00000000 00000000 00038800
+20124000 01001101 00000096 00000001
diff --git a/configs/ls1046aqds_defconfig b/configs/ls1046aqds_defconfig
new file mode 100644
index 0000000..71c3b95
--- /dev/null
+++ b/configs/ls1046aqds_defconfig
@@ -0,0 +1,28 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1046AQDS=y
+CONFIG_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_BOOTDELAY=10
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_SYS_NS16550=y
+CONFIG_FSL_DSPI=y
diff --git a/configs/ls1046aqds_nand_defconfig b/configs/ls1046aqds_nand_defconfig
new file mode 100644
index 0000000..b29796d
--- /dev/null
+++ b/configs/ls1046aqds_nand_defconfig
@@ -0,0 +1,30 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1046AQDS=y
+CONFIG_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,RAMBOOT_PBL,SPL_FSL_PBL"
+CONFIG_NAND_BOOT=y
+CONFIG_BOOTDELAY=10
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_SYS_NS16550=y
+CONFIG_FSL_DSPI=y
diff --git a/configs/ls1046aqds_qspi_defconfig b/configs/ls1046aqds_qspi_defconfig
new file mode 100644
index 0000000..bdcb2d1
--- /dev/null
+++ b/configs/ls1046aqds_qspi_defconfig
@@ -0,0 +1,31 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1046AQDS=y
+CONFIG_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_QSPI_BOOT=y
+CONFIG_BOOTDELAY=10
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_SYS_NS16550=y
+CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
diff --git a/configs/ls1046aqds_sdcard_ifc_defconfig b/configs/ls1046aqds_sdcard_ifc_defconfig
new file mode 100644
index 0000000..044bd6e
--- /dev/null
+++ b/configs/ls1046aqds_sdcard_ifc_defconfig
@@ -0,0 +1,30 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1046AQDS=y
+CONFIG_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,RAMBOOT_PBL,SPL_FSL_PBL"
+CONFIG_SD_BOOT=y
+CONFIG_BOOTDELAY=10
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_SYS_NS16550=y
+CONFIG_FSL_DSPI=y
diff --git a/configs/ls1046aqds_sdcard_qspi_defconfig b/configs/ls1046aqds_sdcard_qspi_defconfig
new file mode 100644
index 0000000..cb8e635
--- /dev/null
+++ b/configs/ls1046aqds_sdcard_qspi_defconfig
@@ -0,0 +1,32 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1046AQDS=y
+CONFIG_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT_QSPI"
+CONFIG_SD_BOOT=y
+CONFIG_BOOTDELAY=10
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_SYS_NS16550=y
+CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
diff --git a/include/configs/ls1046a_common.h b/include/configs/ls1046a_common.h
index 9ee29b4..5856de8 100644
--- a/include/configs/ls1046a_common.h
+++ b/include/configs/ls1046a_common.h
@@ -80,6 +80,36 @@
 #define CONFIG_SYS_MONITOR_LEN		0xa0000
 #endif
 
+/* NAND SPL */
+#ifdef CONFIG_NAND_BOOT
+#define CONFIG_SPL_PBL_PAD
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_WATCHDOG_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_SPL_TEXT_BASE		0x10000000
+#define CONFIG_SPL_MAX_SIZE		0x1d000		/* 116 KiB */
+#define CONFIG_SPL_STACK		0x1001f000
+#define CONFIG_SYS_NAND_U_BOOT_DST	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_SPL_BSS_START_ADDR	0x8f000000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x80000
+#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
+					CONFIG_SPL_BSS_MAX_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
+#define CONFIG_SYS_MONITOR_LEN		0xa0000
+#endif
+
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
@@ -117,13 +147,19 @@
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 #define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x820)
-#else
+#elif defined(CONFIG_QSPI_BOOT)
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 #define CONFIG_SYS_FMAN_FW_ADDR		0x40300000
 #define CONFIG_ENV_SPI_BUS		0
 #define CONFIG_ENV_SPI_CS		0
 #define CONFIG_ENV_SPI_MAX_HZ		1000000
 #define CONFIG_ENV_SPI_MODE		0x03
+#elif defined(CONFIG_NAND_BOOT)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_FMAN_FW_ADDR		(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_FMAN_FW_ADDR		0x60300000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
diff --git a/include/configs/ls1046aqds.h b/include/configs/ls1046aqds.h
new file mode 100644
index 0000000..2e5c2f1
--- /dev/null
+++ b/include/configs/ls1046aqds.h
@@ -0,0 +1,487 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __LS1046AQDS_H__
+#define __LS1046AQDS_H__
+
+#include "ls1046a_common.h"
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
+#define CONFIG_SYS_TEXT_BASE		0x82000000
+#elif defined(CONFIG_QSPI_BOOT)
+#define CONFIG_SYS_TEXT_BASE		0x40010000
+#else
+#define CONFIG_SYS_TEXT_BASE		0x60100000
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+#define CONFIG_LAYERSCAPE_NS_ACCESS
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+/* Physical Memory Map */
+#define CONFIG_CHIP_SELECTS_PER_CTRL	4
+#define CONFIG_NR_DRAM_BANKS		2
+
+#define CONFIG_DDR_SPD
+#define SPD_EEPROM_ADDRESS		0x51
+#define CONFIG_SYS_SPD_BUS_NUM		0
+
+#define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
+
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE           0xdeadbeef
+#endif
+
+#define CONFIG_SYS_HAS_SERDES
+
+/* DSPI */
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
+#define CONFIG_SPI_FLASH_SST		/* cs1 */
+#define CONFIG_SPI_FLASH_EON		/* cs2 */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SF_DEFAULT_BUS		1
+#define CONFIG_SF_DEFAULT_CS		0
+#endif
+#endif
+
+/* QSPI */
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE		(1 << 24)
+#define FSL_QSPI_FLASH_NUM		2
+#endif
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHYLIB_10G
+#define RGMII_PHY1_ADDR		0x1
+#define RGMII_PHY2_ADDR		0x2
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+/* PHY address on QSGMII riser card on slot 2 */
+#define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
+#define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
+#define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
+#define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
+#endif
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_SYS_FSL_PBL_PBI \
+	board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
+#endif
+
+#ifdef CONFIG_NAND_BOOT
+#define CONFIG_SYS_FSL_PBL_RCW \
+	board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
+#endif
+
+#ifdef CONFIG_SD_BOOT
+#ifdef CONFIG_SD_BOOT_QSPI
+#define CONFIG_SYS_FSL_PBL_RCW \
+	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
+#else
+#define CONFIG_SYS_FSL_PBL_RCW \
+	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
+#endif
+#endif
+
+/* IFC */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define	CONFIG_FSL_IFC
+/*
+ * CONFIG_SYS_FLASH_BASE has the final address (core view)
+ * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
+ * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
+ * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
+ */
+#define CONFIG_SYS_FLASH_BASE			0x60000000
+#define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
+
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
+#endif
+#endif
+
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SCSI
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM		0
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+
+#define CONFIG_SYS_SATA				AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
+#define CONFIG_SYS_SCSI_MAX_LUN			1
+#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+						CONFIG_SYS_SCSI_MAX_LUN)
+
+/*
+ * IFC Definitions
+ */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
+#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
+#define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+				+ 0x8000000) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
+
+#define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
+					CSOR_NOR_TRHZ_80)
+#define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
+					FTIM0_NOR_TEADC(0x5) | \
+					FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
+					FTIM1_NOR_TRAD_NOR(0x1a) | \
+					FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x4) | \
+					FTIM2_NOR_TCH(0x4) | \
+					FTIM2_NOR_TWPH(0xe) | \
+					FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3		0
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
+					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
+
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#define CONFIG_SYS_WRITE_SWAPPED_DATA
+
+/*
+ * NAND Flash Definitions
+ */
+#define CONFIG_NAND_FSL_IFC
+
+#define CONFIG_SYS_NAND_BASE		0x7e800000
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
+
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8	\
+				| CSPR_MSEL_NAND	\
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
+				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
+				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
+				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x7) | \
+					FTIM0_NAND_TWH(0xa))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0xe)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
+					FTIM2_NAND_TREH(0xa) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3           0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * 1024)
+#endif
+
+#ifdef CONFIG_NAND_BOOT
+#define CONFIG_SPL_PAD_TO		0x40000		/* block aligned */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
+#endif
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_QIXIS_I2C_ACCESS
+#define CONFIG_SYS_I2C_EARLY_INIT
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+/*
+ * QIXIS Definitions
+ */
+#define CONFIG_FSL_QIXIS
+
+#ifdef CONFIG_FSL_QIXIS
+#define QIXIS_BASE			0x7fb00000
+#define QIXIS_BASE_PHYS			QIXIS_BASE
+#define CONFIG_SYS_I2C_FPGA_ADDR	0x66
+#define QIXIS_LBMAP_SWITCH		6
+#define QIXIS_LBMAP_MASK		0x0f
+#define QIXIS_LBMAP_SHIFT		0
+#define QIXIS_LBMAP_DFLTBANK		0x00
+#define QIXIS_LBMAP_ALTBANK		0x04
+#define QIXIS_LBMAP_NAND		0x09
+#define QIXIS_LBMAP_SD			0x00
+#define QIXIS_LBMAP_SD_QSPI		0xff
+#define QIXIS_LBMAP_QSPI		0xff
+#define QIXIS_RCW_SRC_NAND		0x110
+#define QIXIS_RCW_SRC_SD		0x040
+#define QIXIS_RCW_SRC_QSPI		0x045
+#define QIXIS_RST_CTL_RESET		0x41
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
+
+#define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
+#define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
+					CSPR_PORT_SIZE_8 | \
+					CSPR_MSEL_GPCM | \
+					CSPR_V)
+#define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
+					CSOR_NOR_NOR_MODE_AVD_NOR | \
+					CSOR_NOR_TRHZ_80)
+
+/*
+ * QIXIS Timing parameters for IFC GPCM
+ */
+#define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
+					FTIM0_GPCM_TEADC(0x20) | \
+					FTIM0_GPCM_TEAHC(0x10))
+#define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
+					FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
+					FTIM2_GPCM_TCH(0x8) | \
+					FTIM2_GPCM_TWP(0xf0))
+#define CONFIG_SYS_FPGA_FTIM3		0x0
+#endif
+
+#ifdef CONFIG_NAND_BOOT
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
+#define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
+#define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
+#define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
+#define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
+#define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
+#define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
+#define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
+#define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
+#define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
+#define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
+#endif
+
+/*
+ * I2C bus multiplexer
+ */
+#define I2C_MUX_PCA_ADDR_PRI		0x77
+#define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR		0x18
+#define I2C_MUX_CH_DEFAULT		0x8
+#define I2C_MUX_CH_CH7301		0xC
+#define I2C_MUX_CH5			0xD
+#define I2C_MUX_CH6			0xE
+#define I2C_MUX_CH7			0xF
+
+#define I2C_MUX_CH_VOL_MONITOR 0xa
+
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR           0x40
+#define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF      0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT    3
+
+#define CONFIG_VID_FLS_ENV		"ls1046aqds_vdd_mv"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_VID
+#endif
+#define CONFIG_VOL_MONITOR_IR36021_SET
+#define CONFIG_VOL_MONITOR_INA220
+/* The lowest and highest voltage allowed for LS1046AQDS */
+#define VDD_MV_MIN			819
+#define VDD_MV_MAX			1212
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_PBSIZE		\
+		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		0x9fffffff
+
+#define CONFIG_SYS_HZ			1000
+
+/*
+ * Stack sizes
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE		(30 * 1024)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_NAND_BOOT
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_ENV_OFFSET		(1024 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_SIZE			0x2000
+#elif defined(CONFIG_QSPI_BOOT)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE			0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET		0x100000        /* 1MB */
+#define CONFIG_ENV_SECT_SIZE		0x10000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_SECT_SIZE		0x20000
+#define CONFIG_ENV_SIZE			0x20000
+#endif
+
+#define CONFIG_CMDLINE_TAG
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_BOOTCOMMAND		"sf probe && sf read $kernel_load "    \
+					"e0000 f00000 && bootm $kernel_load"
+#else
+#define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
+					"$kernel_size && bootm $kernel_load"
+#endif
+
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
+#define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:2m(uboot)," \
+			"14m(free)"
+#else
+#define MTDPARTS_DEFAULT "mtdparts=60000000.nor:1m(nor_bank0_rcw)," \
+			"1m(nor_bank0_uboot),1m(nor_bank0_uboot_env)," \
+			"1m(nor_bank0_fman_uconde),40m(nor_bank0_fit)," \
+			"1m(nor_bank4_rcw),1m(nor_bank4_uboot)," \
+			"1m(nor_bank4_uboot_env),1m(nor_bank4_fman_ucode)," \
+			"40m(nor_bank4_fit);7e800000.flash:" \
+			"4m(nand_uboot),36m(nand_kernel)," \
+			"472m(nand_free);spi0.0:2m(uboot)," \
+			"14m(free)"
+#endif
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LS1046AQDS_H__ */