mtd: nand: omap: add CONFIG_SYS_NAND_BUSWIDTH_16BIT to indicate NAND device bus-width

GPMC controller needs to be configured based on bus-width of the NAND device
connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI
parameters is not possible in following situations:
SPL:    SPL NAND drivers does not support ONFI parameter reading.
U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init()
        which is called before probing for devices, hence any ONFI parameter
        information is not available during GPMC initialization.

Thus, OMAP NAND driver expected board developers to explicitely write GPMC
configurations specific to NAND device attached on board in board files itself.
But this was troublesome for board manufacturers as they need to dive into
lengthy platform & SoC documents to find details of GPMC registers and
appropriate configurations to get NAND device working.

This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config
hich indicates that connected NAND device has x16 bus-width. And then based on
this config GPMC driver itself initializes itself based on NAND bus-width. This
keeps board developers free from knowing GPMC controller specific internals.

Signed-off-by: Pekon Gupta <pekon@ti.com>

13 files changed, 38 insertions, 5 deletions

diff --git a/doc/README.nand b/doc/README.nand
index b91f198..2bc5b39 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -190,6 +190,24 @@ Configuration Options:
 	This is used by SoC platforms which do not have built-in ELM
 	hardware engine required for BCH ECC correction.
 
+   CONFIG_SYS_NAND_BUSWIDTH_16BIT
+	Indicates that NAND device has 16-bit wide data-bus. In absence of this
+	config, bus-width of NAND device is assumed to be either 8-bit and later
+	determined by reading ONFI params.
+	Above config is useful when NAND device's bus-width information cannot
+	be determined from on-chip ONFI params, like in following scenarios:
+	- SPL boot does not support reading of ONFI parameters. This is done to
+	  keep SPL code foot-print small.
+	- In current U-Boot flow using nand_init(), driver initialization
+	  happens in board_nand_init() which is called before any device probe
+	  (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
+	  not available while configuring controller. So a static CONFIG_NAND_xx
+	  is needed to know the device's bus-width in advance.
+	Some drivers using above config are:
+	drivers/mtd/nand/mxc_nand.c
+	drivers/mtd/nand/ndfc.c
+	drivers/mtd/nand/omap_gpmc.c
+
 
 Platform specific options
 =========================
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c
index d2fedf9..cdfa6bc 100644
--- a/drivers/mtd/nand/omap_gpmc.c
+++ b/drivers/mtd/nand/omap_gpmc.c
@@ -782,13 +782,18 @@ int board_nand_init(struct nand_chip *nand)
 	nand->priv	= &omap_nand_info;
 	nand->cmd_ctrl	= omap_nand_hwcontrol;
 	nand->options	|= NAND_NO_PADDING | NAND_CACHEPRG;
-	/* If we are 16 bit dev, our gpmc config tells us that */
-	if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000)
-		nand->options |= NAND_BUSWIDTH_16;
-
 	nand->chip_delay = 100;
 	nand->ecc.layout = &omap_ecclayout;
 
+	/* configure driver and controller based on NAND device bus-width */
+	gpmc_config = readl(&gpmc_cfg->cs[cs].config1);
+#if defined(CONFIG_SYS_NAND_BUSWIDTH_16BIT)
+	nand->options |= NAND_BUSWIDTH_16;
+	writel(gpmc_config | (0x1 << 12), &gpmc_cfg->cs[cs].config1);
+#else
+	nand->options &= ~NAND_BUSWIDTH_16;
+	writel(gpmc_config & ~(0x1 << 12), &gpmc_cfg->cs[cs].config1);
+#endif
 	/* select ECC scheme */
 #if defined(CONFIG_NAND_OMAP_ECCSCHEME)
 	err = omap_select_ecc_scheme(nand, CONFIG_NAND_OMAP_ECCSCHEME,
diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h
index 4407b45..ad4cbd8 100644
--- a/include/configs/am3517_crane.h
+++ b/include/configs/am3517_crane.h
@@ -329,6 +329,7 @@
 #define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/omap-common/u-boot-spl.lds"
 
 /* NAND boot config */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index 16a00eb..5308790 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -314,6 +314,7 @@
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
 
 /* NAND boot config */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048
diff --git a/include/configs/dig297.h b/include/configs/dig297.h
index af6f56b..ce205e9 100644
--- a/include/configs/dig297.h
+++ b/include/configs/dig297.h
@@ -138,6 +138,7 @@
  * Board NAND Info.
  */
 #define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 #define CONFIG_SYS_NAND_ADDR		NAND_BASE	/* physical address */
 							/* to access nand */
 #define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 0a7df60..c023483 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -295,6 +295,7 @@
 #define CONFIG_SPL_OMAP3_ID_NAND
 
 /* NAND boot config */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048
diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h
index 7f3424b..ae4ce63 100644
--- a/include/configs/omap3_evm_common.h
+++ b/include/configs/omap3_evm_common.h
@@ -120,7 +120,7 @@
 
 /* Max number of NAND devices */
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
-
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 /* Timeout values (in ticks) */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
 #define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h
index d56d5b0..79daabd 100644
--- a/include/configs/omap3_igep00x0.h
+++ b/include/configs/omap3_igep00x0.h
@@ -187,6 +187,7 @@
 
 /* NAND boot config */
 #ifdef CONFIG_NAND
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048
diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index 0d03c75..8dcbba3 100644
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -141,6 +141,7 @@
 
 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of */
 							/* NAND devices */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 #define CONFIG_JFFS2_NAND
 /* nand device jffs2 lives on */
 #define CONFIG_JFFS2_DEV		"nand0"
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 7b97be9..1a13633 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -206,6 +206,7 @@
 #define CONFIG_SYS_CACHELINE_SIZE	64
 
 /* NAND boot config */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index 7c5540f..3efe4cf 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -98,6 +98,7 @@
 #define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
 							/* to access nand at */
 							/* CS0 */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 
 /* Environment information */
 
diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index 3522c1a..eda536b 100644
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -249,6 +249,7 @@
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
 
 /* NAND boot config */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048
 #define CONFIG_SYS_NAND_OOBSIZE		64
diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h
index 9c04c23..4471935 100644
--- a/include/configs/tao3530.h
+++ b/include/configs/tao3530.h
@@ -141,6 +141,7 @@
 
 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
 							/* devices */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT	16
 /* Environment information */
 #define CONFIG_BOOTDELAY		3