ARM: remove jadecpu board support

This is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Weisser <weisserm@arcor.de>
Acked-by: Marek Vasut <marex@denx.de>

20 files changed, 19 insertions, 1745 deletions

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3408319..089bef2 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -144,10 +144,6 @@ config TARGET_DEVKIT3250
 	bool "Support devkit3250"
 	select CPU_ARM926EJS
 
-config TARGET_JADECPU
-	bool "Support jadecpu"
-	select CPU_ARM926EJS
-
 config TARGET_MX25PDK
 	bool "Support mx25pdk"
 	select CPU_ARM926EJS
@@ -852,7 +848,6 @@ source "board/st-ericsson/snowball/Kconfig"
 source "board/st-ericsson/u8500/Kconfig"
 source "board/st/stv0991/Kconfig"
 source "board/sunxi/Kconfig"
-source "board/syteco/jadecpu/Kconfig"
 source "board/syteco/zmx25/Kconfig"
 source "board/tbs/tbs2910/Kconfig"
 source "board/ti/am335x/Kconfig"
diff --git a/arch/arm/cpu/arm926ejs/Makefile b/arch/arm/cpu/arm926ejs/Makefile
index f5944cc..ac23116 100644
--- a/arch/arm/cpu/arm926ejs/Makefile
+++ b/arch/arm/cpu/arm926ejs/Makefile
@@ -16,7 +16,6 @@ endif
 
 obj-$(CONFIG_ARMADA100) += armada100/
 obj-$(if $(filter lpc32xx,$(SOC)),y) += lpc32xx/
-obj-$(CONFIG_MB86R0x) += mb86r0x/
 obj-$(CONFIG_MX25) += mx25/
 obj-$(CONFIG_MX27) += mx27/
 obj-$(if $(filter mxs,$(SOC)),y) += mxs/
diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/Makefile b/arch/arm/cpu/arm926ejs/mb86r0x/Makefile
deleted file mode 100644
index 365892c..0000000
--- a/arch/arm/cpu/arm926ejs/mb86r0x/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= clock.o reset.o timer.o
diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/clock.c b/arch/arm/cpu/arm926ejs/mb86r0x/clock.c
deleted file mode 100644
index 1f6f66e..0000000
--- a/arch/arm/cpu/arm926ejs/mb86r0x/clock.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-
-/*
- * Get the peripheral bus frequency depending on pll pin settings
- */
-ulong get_bus_freq(ulong dummy)
-{
-	struct mb86r0x_crg * crg = (struct mb86r0x_crg *)
-					MB86R0x_CRG_BASE;
-	uint32_t pllmode;
-
-	pllmode = readl(&crg->crpr) & MB86R0x_CRG_CRPR_PLLMODE;
-
-	if (pllmode == MB86R0x_CRG_CRPR_PLLMODE_X20)
-		return 40000000;
-
-	return 41164767;
-}
diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/reset.c b/arch/arm/cpu/arm926ejs/mb86r0x/reset.c
deleted file mode 100644
index 7bd77ff..0000000
--- a/arch/arm/cpu/arm926ejs/mb86r0x/reset.c
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-
-/*
- * Reset the cpu by setting software reset request bit
- */
-void reset_cpu(ulong ignored)
-{
-	struct mb86r0x_crg * crg = (struct mb86r0x_crg *)
-					MB86R0x_CRG_BASE;
-
-	writel(MB86R0x_CRSR_SWRSTREQ, &crg->crsr);
-	while (1)
-		/* NOP */;
-	/* Never reached */
-}
diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/timer.c b/arch/arm/cpu/arm926ejs/mb86r0x/timer.c
deleted file mode 100644
index bb07819..0000000
--- a/arch/arm/cpu/arm926ejs/mb86r0x/timer.c
+++ /dev/null
@@ -1,115 +0,0 @@
-/*
- * (C) Copyright 2007-2008
- * Stelian Pop <stelian@popies.net>
- * Lead Tech Design <www.leadtechdesign.com>
- *
- * (C) Copyright 2010
- * Matthias Weisser, Graf-Syteco <weisserm@arcor.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <div64.h>
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-
-#define TIMER_LOAD_VAL	0xffffffff
-#define TIMER_FREQ	(CONFIG_MB86R0x_IOCLK  / 256)
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define timestamp gd->arch.tbl
-#define lastdec gd->arch.lastinc
-
-static inline unsigned long long tick_to_time(unsigned long long tick)
-{
-	tick *= CONFIG_SYS_HZ;
-	do_div(tick, TIMER_FREQ);
-
-	return tick;
-}
-
-static inline unsigned long long usec_to_tick(unsigned long long usec)
-{
-	usec *= TIMER_FREQ;
-	do_div(usec, 1000000);
-
-	return usec;
-}
-
-/* nothing really to do with interrupts, just starts up a counter. */
-int timer_init(void)
-{
-	struct mb86r0x_timer * timer = (struct mb86r0x_timer *)
-					MB86R0x_TIMER_BASE;
-	ulong ctrl = readl(&timer->control);
-
-	writel(TIMER_LOAD_VAL, &timer->load);
-
-	ctrl |= MB86R0x_TIMER_ENABLE | MB86R0x_TIMER_PRS_8S |
-		MB86R0x_TIMER_SIZE_32;
-
-	writel(ctrl, &timer->control);
-
-	/* capture current value time */
-	lastdec = readl(&timer->value);
-	timestamp = 0; /* start "advancing" time stamp from 0 */
-
-	return 0;
-}
-
-/*
- * timer without interrupts
- */
-unsigned long long get_ticks(void)
-{
-	struct mb86r0x_timer * timer = (struct mb86r0x_timer *)
-					MB86R0x_TIMER_BASE;
-	ulong now = readl(&timer->value);
-
-	if (now <= lastdec) {
-		/* normal mode (non roll) */
-		/* move stamp forward with absolut diff ticks */
-		timestamp += lastdec - now;
-	} else {
-		/* we have rollover of incrementer */
-		timestamp += lastdec + TIMER_LOAD_VAL - now;
-	}
-	lastdec = now;
-	return timestamp;
-}
-
-ulong get_timer_masked(void)
-{
-	return tick_to_time(get_ticks());
-}
-
-void __udelay(unsigned long usec)
-{
-	unsigned long long tmp;
-	ulong tmo;
-
-	tmo = usec_to_tick(usec);
-	tmp = get_ticks();			/* get current timestamp */
-
-	while ((get_ticks() - tmp) < tmo)	/* loop till event */
-		 /*NOP*/;
-}
-
-ulong get_timer(ulong base)
-{
-	return get_timer_masked() - base;
-}
-
-/*
- * This function is derived from PowerPC code (timebase clock frequency).
- * On ARM it returns the number of timer ticks per second.
- */
-ulong get_tbclk(void)
-{
-	ulong tbclk;
-
-	tbclk = TIMER_FREQ;
-	return tbclk;
-}
diff --git a/arch/arm/include/asm/arch-mb86r0x/hardware.h b/arch/arm/include/asm/arch-mb86r0x/hardware.h
deleted file mode 100644
index 42a52bc..0000000
--- a/arch/arm/include/asm/arch-mb86r0x/hardware.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/*
- * (C) Copyright 2007
- *
- * Author : Carsten Schneider, mycable GmbH
- *          <cs@mycable.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#include <linux/sizes.h>
-#include <asm/arch/mb86r0x.h>
-
-#endif
diff --git a/arch/arm/include/asm/arch-mb86r0x/mb86r0x.h b/arch/arm/include/asm/arch-mb86r0x/mb86r0x.h
deleted file mode 100644
index 7fec971..0000000
--- a/arch/arm/include/asm/arch-mb86r0x/mb86r0x.h
+++ /dev/null
@@ -1,599 +0,0 @@
-/*
- * (C) Copyright 2007
- *
- * mb86r0x definitions
- *
- * Author : Carsten Schneider, mycable GmbH
- *          <cs@mycable.de>
- *
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef MB86R0X_H
-#define MB86R0X_H
-
-#ifndef __ASSEMBLY__
-
-/* GPIO registers */
-struct mb86r0x_gpio {
-	uint32_t gpdr0;
-	uint32_t gpdr1;
-	uint32_t gpdr2;
-	uint32_t res;
-	uint32_t gpddr0;
-	uint32_t gpddr1;
-	uint32_t gpddr2;
-};
-
-/* PWM registers */
-struct mb86r0x_pwm {
-	uint32_t bcr;
-	uint32_t tpr;
-	uint32_t pr;
-	uint32_t dr;
-	uint32_t cr;
-	uint32_t sr;
-	uint32_t ccr;
-	uint32_t ir;
-};
-
-/* The mb86r0x chip control (CCNT) register set. */
-struct mb86r0x_ccnt {
-	uint32_t ccid;
-	uint32_t csrst;
-	uint32_t pad0[2];
-	uint32_t cist;
-	uint32_t cistm;
-	uint32_t cgpio_ist;
-	uint32_t cgpio_istm;
-	uint32_t cgpio_ip;
-	uint32_t cgpio_im;
-	uint32_t caxi_bw;
-	uint32_t caxi_ps;
-	uint32_t cmux_md;
-	uint32_t cex_pin_st;
-	uint32_t cmlb;
-	uint32_t pad1[1];
-	uint32_t cusb;
-	uint32_t pad2[41];
-	uint32_t cbsc;
-	uint32_t cdcrc;
-	uint32_t cmsr0;
-	uint32_t cmsr1;
-	uint32_t pad3[2];
-};
-
-/* The mb86r0x clock reset generator */
-struct mb86r0x_crg {
-	uint32_t crpr;
-	uint32_t pad0;
-	uint32_t crwr;
-	uint32_t crsr;
-	uint32_t crda;
-	uint32_t crdb;
-	uint32_t crha;
-	uint32_t crpa;
-	uint32_t crpb;
-	uint32_t crhb;
-	uint32_t cram;
-};
-
-/* The mb86r0x timer */
-struct mb86r0x_timer {
-	uint32_t load;
-	uint32_t value;
-	uint32_t control;
-	uint32_t intclr;
-	uint32_t ris;
-	uint32_t mis;
-	uint32_t bgload;
-};
-
-/* mb86r0x gdc display controller */
-struct mb86r0x_gdc_dsp {
-	/* Display settings */
-	uint32_t dcm0;
-	uint16_t pad00;
-	uint16_t htp;
-	uint16_t hdp;
-	uint16_t hdb;
-	uint16_t hsp;
-	uint8_t  hsw;
-	uint8_t  vsw;
-	uint16_t pad01;
-	uint16_t vtr;
-	uint16_t vsp;
-	uint16_t vdp;
-	uint16_t wx;
-	uint16_t wy;
-	uint16_t ww;
-	uint16_t wh;
-
-	/* Layer 0 */
-	uint32_t l0m;
-	uint32_t l0oa;
-	uint32_t l0da;
-	uint16_t l0dx;
-	uint16_t l0dy;
-
-	/* Layer 1 */
-	uint32_t l1m;
-	uint32_t cbda0;
-	uint32_t cbda1;
-	uint32_t pad02;
-
-	/* Layer 2 */
-	uint32_t l2m;
-	uint32_t l2oa0;
-	uint32_t l2da0;
-	uint32_t l2oa1;
-	uint32_t l2da1;
-	uint16_t l2dx;
-	uint16_t l2dy;
-
-	/* Layer 3 */
-	uint32_t l3m;
-	uint32_t l3oa0;
-	uint32_t l3da0;
-	uint32_t l3oa1;
-	uint32_t l3da1;
-	uint16_t l3dx;
-	uint16_t l3dy;
-
-	/* Layer 4 */
-	uint32_t l4m;
-	uint32_t l4oa0;
-	uint32_t l4da0;
-	uint32_t l4oa1;
-	uint32_t l4da1;
-	uint16_t l4dx;
-	uint16_t l4dy;
-
-	/* Layer 5 */
-	uint32_t l5m;
-	uint32_t l5oa0;
-	uint32_t l5da0;
-	uint32_t l5oa1;
-	uint32_t l5da1;
-	uint16_t l5dx;
-	uint16_t l5dy;
-
-	/* Cursor */
-	uint16_t cutc;
-	uint8_t  cpm;
-	uint8_t  csize;
-	uint32_t cuoa0;
-	uint16_t cux0;
-	uint16_t cuy0;
-	uint32_t cuoa1;
-	uint16_t cux1;
-	uint16_t cuy1;
-
-	/* Layer blending */
-	uint32_t l0bld;
-	uint32_t pad03;
-	uint32_t l0tc;
-	uint16_t l3tc;
-	uint16_t l2tc;
-	uint32_t pad04[15];
-
-	/* Display settings */
-	uint32_t dcm1;
-	uint32_t dcm2;
-	uint32_t dcm3;
-	uint32_t pad05;
-
-	/* Layer 0 extended */
-	uint32_t l0em;
-	uint16_t l0wx;
-	uint16_t l0wy;
-	uint16_t l0ww;
-	uint16_t l0wh;
-	uint32_t pad06;
-
-	/* Layer 1 extended */
-	uint32_t l1em;
-	uint16_t l1wx;
-	uint16_t l1wy;
-	uint16_t l1ww;
-	uint16_t l1wh;
-	uint32_t pad07;
-
-	/* Layer 2 extended */
-	uint32_t l2em;
-	uint16_t l2wx;
-	uint16_t l2wy;
-	uint16_t l2ww;
-	uint16_t l2wh;
-	uint32_t pad08;
-
-	/* Layer 3 extended */
-	uint32_t l3em;
-	uint16_t l3wx;
-	uint16_t l3wy;
-	uint16_t l3ww;
-	uint16_t l3wh;
-	uint32_t pad09;
-
-	/* Layer 4 extended */
-	uint32_t l4em;
-	uint16_t l4wx;
-	uint16_t l4wy;
-	uint16_t l4ww;
-	uint16_t l4wh;
-	uint32_t pad10;
-
-	/* Layer 5 extended */
-	uint32_t l5em;
-	uint16_t l5wx;
-	uint16_t l5wy;
-	uint16_t l5ww;
-	uint16_t l5wh;
-	uint32_t pad11;
-
-	/* Multi screen control */
-	uint32_t msc;
-	uint32_t pad12[3];
-	uint32_t dls;
-	uint32_t dbgc;
-
-	/* Layer blending */
-	uint32_t l1bld;
-	uint32_t l2bld;
-	uint32_t l3bld;
-	uint32_t l4bld;
-	uint32_t l5bld;
-	uint32_t pad13;
-
-	/* Extended transparency control */
-	uint32_t l0etc;
-	uint32_t l1etc;
-	uint32_t l2etc;
-	uint32_t l3etc;
-	uint32_t l4etc;
-	uint32_t l5etc;
-	uint32_t pad14[10];
-
-	/* YUV coefficients */
-	uint32_t l1ycr0;
-	uint32_t l1ycr1;
-	uint32_t l1ycg0;
-	uint32_t l1ycg1;
-	uint32_t l1ycb0;
-	uint32_t l1ycb1;
-	uint32_t pad15[130];
-
-	/* Layer palletes */
-	uint32_t l0pal[256];
-	uint32_t l1pal[256];
-	uint32_t pad16[256];
-	uint32_t l2pal[256];
-	uint32_t l3pal[256];
-	uint32_t pad17[256];
-
-	/* PWM settings */
-	uint32_t vpwmm;
-	uint16_t vpwms;
-	uint16_t vpwme;
-	uint32_t vpwmc;
-	uint32_t pad18[253];
-};
-
-/* mb86r0x gdc capture controller */
-struct mb86r0x_gdc_cap {
-	uint32_t vcm;
-	uint32_t csc;
-	uint32_t vcs;
-	uint32_t pad01;
-
-	uint32_t cbm;
-	uint32_t cboa;
-	uint32_t cbla;
-	uint16_t cihstr;
-	uint16_t civstr;
-	uint16_t cihend;
-	uint16_t civend;
-	uint32_t pad02;
-
-	uint32_t chp;
-	uint32_t cvp;
-	uint32_t pad03[4];
-
-	uint32_t clpf;
-	uint32_t pad04;
-	uint32_t cmss;
-	uint32_t cmds;
-	uint32_t pad05[12];
-
-	uint32_t rgbhc;
-	uint32_t rgbhen;
-	uint32_t rgbven;
-	uint32_t pad06;
-	uint32_t rgbs;
-	uint32_t pad07[11];
-
-	uint32_t rgbcmy;
-	uint32_t rgbcmcb;
-	uint32_t rgbcmcr;
-	uint32_t rgbcmb;
-	uint32_t pad08[12 + 1984];
-};
-
-/* mb86r0x gdc draw */
-struct mb86r0x_gdc_draw {
-	uint32_t ys;
-	uint32_t xs;
-	uint32_t dxdy;
-	uint32_t xus;
-	uint32_t dxudy;
-	uint32_t xls;
-	uint32_t dxldy;
-	uint32_t usn;
-	uint32_t lsn;
-	uint32_t pad01[7];
-	uint32_t rs;
-	uint32_t drdx;
-	uint32_t drdy;
-	uint32_t gs;
-	uint32_t dgdx;
-	uint32_t dgdy;
-	uint32_t bs;
-	uint32_t dbdx;
-	uint32_t dbdy;
-	uint32_t pad02[7];
-	uint32_t zs;
-	uint32_t dzdx;
-	uint32_t dzdy;
-	uint32_t pad03[13];
-	uint32_t ss;
-	uint32_t dsdx;
-	uint32_t dsdy;
-	uint32_t ts;
-	uint32_t dtdx;
-	uint32_t dtdy;
-	uint32_t qs;
-	uint32_t dqdx;
-	uint32_t dqdy;
-	uint32_t pad04[23];
-	uint32_t lpn;
-	uint32_t lxs;
-	uint32_t lxde;
-	uint32_t lys;
-	uint32_t lyde;
-	uint32_t lzs;
-	uint32_t lzde;
-	uint32_t pad05[13];
-	uint32_t pxdc;
-	uint32_t pydc;
-	uint32_t pzdc;
-	uint32_t pad06[25];
-	uint32_t rxs;
-	uint32_t rys;
-	uint32_t rsizex;
-	uint32_t rsizey;
-	uint32_t pad07[12];
-	uint32_t saddr;
-	uint32_t sstride;
-	uint32_t srx;
-	uint32_t sry;
-	uint32_t daddr;
-	uint32_t dstride;
-	uint32_t drx;
-	uint32_t dry;
-	uint32_t brsizex;
-	uint32_t brsizey;
-	uint32_t tcolor;
-	uint32_t pad08[93];
-	uint32_t blpo;
-	uint32_t pad09[7];
-	uint32_t ctr;
-	uint32_t ifsr;
-	uint32_t ifcnt;
-	uint32_t sst;
-	uint32_t ds;
-	uint32_t pst;
-	uint32_t est;
-	uint32_t pad10;
-	uint32_t mdr0;
-	uint32_t mdr1;
-	uint32_t mdr2;
-	uint32_t mdr3;
-	uint32_t mdr4;
-	uint32_t pad14[2];
-	uint32_t mdr7;
-	uint32_t fbr;
-	uint32_t xres;
-	uint32_t zbr;
-	uint32_t tbr;
-	uint32_t pfbr;
-	uint32_t cxmin;
-	uint32_t cxmax;
-	uint32_t cymin;
-	uint32_t cymax;
-	uint32_t txs;
-	uint32_t tis;
-	uint32_t toa;
-	uint32_t sho;
-	uint32_t abr;
-	uint32_t pad15[2];
-	uint32_t fc;
-	uint32_t bc;
-	uint32_t alf;
-	uint32_t blp;
-	uint32_t pad16;
-	uint32_t tbc;
-	uint32_t pad11[42];
-	uint32_t lx0dc;
-	uint32_t ly0dc;
-	uint32_t lx1dc;
-	uint32_t ly1dc;
-	uint32_t pad12[12];
-	uint32_t x0dc;
-	uint32_t y0dc;
-	uint32_t x1dc;
-	uint32_t y1dc;
-	uint32_t x2dc;
-	uint32_t y2dc;
-	uint32_t pad13[666];
-};
-
-/* mb86r0x gdc geometry engine */
-struct mb86r0x_gdc_geom {
-	uint32_t gctr;
-	uint32_t pad00[15];
-	uint32_t gmdr0;
-	uint32_t gmdr1;
-	uint32_t gmdr2;
-	uint32_t pad01[237];
-	uint32_t dfifog;
-	uint32_t pad02[767];
-};
-
-/* mb86r0x gdc */
-struct mb86r0x_gdc {
-	uint32_t pad00[2];
-	uint32_t lts;
-	uint32_t pad01;
-	uint32_t lsta;
-	uint32_t pad02[3];
-	uint32_t ist;
-	uint32_t imask;
-	uint32_t pad03[6];
-	uint32_t lsa;
-	uint32_t lco;
-	uint32_t lreq;
-
-	uint32_t pad04[16*1024 - 19];
-	struct mb86r0x_gdc_dsp dsp0;
-	struct mb86r0x_gdc_dsp dsp1;
-	uint32_t pad05[4*1024 - 2];
-	uint32_t vccc;
-	uint32_t vcsr;
-	struct mb86r0x_gdc_cap cap0;
-	struct mb86r0x_gdc_cap cap1;
-	uint32_t pad06[4*1024];
-	uint32_t texture_base[16*1024];
-	struct mb86r0x_gdc_draw draw;
-	uint32_t pad07[7*1024];
-	struct mb86r0x_gdc_geom geom;
-	uint32_t pad08[7*1024];
-};
-
-/* mb86r0x ddr2c */
-struct mb86r0x_ddr2c {
-	uint16_t dric;
-	uint16_t dric1;
-	uint16_t dric2;
-	uint16_t drca;
-	uint16_t drcm;
-	uint16_t drcst1;
-	uint16_t drcst2;
-	uint16_t drcr;
-	uint16_t pad00[8];
-	uint16_t drcf;
-	uint16_t pad01[7];
-	uint16_t drasr;
-	uint16_t pad02[15];
-	uint16_t drims;
-	uint16_t pad03[7];
-	uint16_t dros;
-	uint16_t pad04;
-	uint16_t dribsodt1;
-	uint16_t dribsocd;
-	uint16_t dribsocd2;
-	uint16_t pad05[3];
-	uint16_t droaba;
-	uint16_t pad06[9];
-	uint16_t drobs;
-	uint16_t pad07[5];
-	uint16_t drimr1;
-	uint16_t drimr2;
-	uint16_t drimr3;
-	uint16_t drimr4;
-	uint16_t droisr1;
-	uint16_t droisr2;
-};
-
-/* mb86r0x memc */
-struct mb86r0x_memc {
-	uint32_t mcfmode[8];
-	uint32_t mcftim[8];
-	uint32_t mcfarea[8];
-};
-
-#endif /* __ASSEMBLY__ */
-
-/*
- * Physical Address Defines
- */
-#define MB86R0x_DDR2_BASE		0xf3000000
-#define MB86R0x_GDC_BASE		0xf1fc0000
-#define MB86R0x_CCNT_BASE		0xfff42000
-#define MB86R0x_CAN0_BASE		0xfff54000
-#define MB86R0x_CAN1_BASE		0xfff55000
-#define MB86R0x_I2C0_BASE		0xfff56000
-#define MB86R0x_I2C1_BASE		0xfff57000
-#define MB86R0x_EHCI_BASE		0xfff80000
-#define MB86R0x_OHCI_BASE		0xfff81000
-#define MB86R0x_IRC1_BASE		0xfffb0000
-#define MB86R0x_MEMC_BASE		0xfffc0000
-#define MB86R0x_TIMER_BASE		0xfffe0000
-#define MB86R0x_UART0_BASE		0xfffe1000
-#define MB86R0x_UART1_BASE		0xfffe2000
-#define MB86R0x_IRCE_BASE		0xfffe4000
-#define MB86R0x_CRG_BASE		0xfffe7000
-#define MB86R0x_IRC0_BASE		0xfffe8000
-#define MB86R0x_GPIO_BASE		0xfffe9000
-#define MB86R0x_PWM0_BASE		0xfff41000
-#define MB86R0x_PWM1_BASE		0xfff41100
-
-#define MB86R0x_CRSR_SWRSTREQ 		(1 << 1)
-
-/*
- * Timer register bits
- */
-#define MB86R0x_TIMER_ENABLE		(1 << 7)
-#define MB86R0x_TIMER_MODE_MSK		(1 << 6)
-#define MB86R0x_TIMER_MODE_FR		(0 << 6)
-#define MB86R0x_TIMER_MODE_PD		(1 << 6)
-
-#define MB86R0x_TIMER_INT_EN		(1 << 5)
-#define MB86R0x_TIMER_PRS_MSK		(3 << 2)
-#define MB86R0x_TIMER_PRS_4S		(1 << 2)
-#define MB86R0x_TIMER_PRS_8S		(1 << 3)
-#define MB86R0x_TIMER_SIZE_32		(1 << 1)
-#define MB86R0x_TIMER_ONE_SHT		(1 << 0)
-
-/*
- * Clock reset generator bits
- */
-#define MB86R0x_CRG_CRPR_PLLRDY		(1 << 8)
-#define MB86R0x_CRG_CRPR_PLLMODE	(0x1f << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X49	(0 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X46	(1 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X37	(2 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X20	(3 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X47	(4 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X44	(5 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X36	(6 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X19	(7 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X39	(8 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X38	(9 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X30	(10 << 0)
-#define MB86R0x_CRG_CRPR_PLLMODE_X15	(11 << 0)
-/*
- * DDR2 controller bits
- */
-#define MB86R0x_DDR2_DRCI_DRINI		(1 << 15)
-#define MB86R0x_DDR2_DRCI_CKEN		(1 << 14)
-#define MB86R0x_DDR2_DRCI_DRCMD		(1 << 0)
-#define MB86R0x_DDR2_DRCI_CMD		(MB86R0x_DDR2_DRCI_DRINI | \
-					MB86R0x_DDR2_DRCI_CKEN | \
-					MB86R0x_DDR2_DRCI_DRCMD)
-#define MB86R0x_DDR2_DRCI_INIT		(MB86R0x_DDR2_DRCI_DRINI | \
-					MB86R0x_DDR2_DRCI_CKEN)
-#define MB86R0x_DDR2_DRCI_NORMAL	MB86R0x_DDR2_DRCI_CKEN
-#endif /* MB86R0X_H */
diff --git a/arch/arm/lib/asm-offsets.c b/arch/arm/lib/asm-offsets.c
index b0c26e5..e5bcaea 100644
--- a/arch/arm/lib/asm-offsets.c
+++ b/arch/arm/lib/asm-offsets.c
@@ -15,9 +15,6 @@
 #include <common.h>
 #include <linux/kbuild.h>
 
-#if defined(CONFIG_MB86R0x)
-#include <asm/arch/mb86r0x.h>
-#endif
 #if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX35) \
 	|| defined(CONFIG_MX51) || defined(CONFIG_MX53)
 #include <asm/arch/imx-regs.h>
@@ -27,8 +24,6 @@ int main(void)
 {
 	/*
 	 * TODO : Check if each entry in this file is really necessary.
-	 *   - struct mb86r0x_ddr2
-	 *   - struct mb86r0x_memc
 	 *   - struct esdramc_regs
 	 *   - struct max_regs
 	 *   - struct aips_regs
@@ -40,47 +35,6 @@ int main(void)
 	 * code. Is it better to define the macros directly in headers?
 	 */
 
-#if defined(CONFIG_MB86R0x)
-	/* ddr2 controller */
-	DEFINE(DDR2_DRIC, offsetof(struct mb86r0x_ddr2c, dric));
-	DEFINE(DDR2_DRIC1, offsetof(struct mb86r0x_ddr2c, dric1));
-	DEFINE(DDR2_DRIC2, offsetof(struct mb86r0x_ddr2c, dric2));
-	DEFINE(DDR2_DRCA, offsetof(struct mb86r0x_ddr2c, drca));
-	DEFINE(DDR2_DRCM, offsetof(struct mb86r0x_ddr2c, drcm));
-	DEFINE(DDR2_DRCST1, offsetof(struct mb86r0x_ddr2c, drcst1));
-	DEFINE(DDR2_DRCST2, offsetof(struct mb86r0x_ddr2c, drcst2));
-	DEFINE(DDR2_DRCR, offsetof(struct mb86r0x_ddr2c, drcr));
-	DEFINE(DDR2_DRCF, offsetof(struct mb86r0x_ddr2c, drcf));
-	DEFINE(DDR2_DRASR, offsetof(struct mb86r0x_ddr2c, drasr));
-	DEFINE(DDR2_DRIMS, offsetof(struct mb86r0x_ddr2c, drims));
-	DEFINE(DDR2_DROS, offsetof(struct mb86r0x_ddr2c, dros));
-	DEFINE(DDR2_DRIBSODT1, offsetof(struct mb86r0x_ddr2c, dribsodt1));
-	DEFINE(DDR2_DROABA, offsetof(struct mb86r0x_ddr2c, droaba));
-	DEFINE(DDR2_DROBS, offsetof(struct mb86r0x_ddr2c, drobs));
-
-	/* clock reset generator */
-	DEFINE(CRG_CRPR, offsetof(struct mb86r0x_crg, crpr));
-	DEFINE(CRG_CRHA, offsetof(struct mb86r0x_crg, crha));
-	DEFINE(CRG_CRPA, offsetof(struct mb86r0x_crg, crpa));
-	DEFINE(CRG_CRPB, offsetof(struct mb86r0x_crg, crpb));
-	DEFINE(CRG_CRHB, offsetof(struct mb86r0x_crg, crhb));
-	DEFINE(CRG_CRAM, offsetof(struct mb86r0x_crg, cram));
-
-	/* chip control module */
-	DEFINE(CCNT_CDCRC, offsetof(struct mb86r0x_ccnt, cdcrc));
-
-	/* external bus interface */
-	DEFINE(MEMC_MCFMODE0, offsetof(struct mb86r0x_memc, mcfmode[0]));
-	DEFINE(MEMC_MCFMODE2, offsetof(struct mb86r0x_memc, mcfmode[2]));
-	DEFINE(MEMC_MCFMODE4, offsetof(struct mb86r0x_memc, mcfmode[4]));
-	DEFINE(MEMC_MCFTIM0, offsetof(struct mb86r0x_memc, mcftim[0]));
-	DEFINE(MEMC_MCFTIM2, offsetof(struct mb86r0x_memc, mcftim[2]));
-	DEFINE(MEMC_MCFTIM4, offsetof(struct mb86r0x_memc, mcftim[4]));
-	DEFINE(MEMC_MCFAREA0, offsetof(struct mb86r0x_memc, mcfarea[0]));
-	DEFINE(MEMC_MCFAREA2, offsetof(struct mb86r0x_memc, mcfarea[2]));
-	DEFINE(MEMC_MCFAREA4, offsetof(struct mb86r0x_memc, mcfarea[4]));
-#endif
-
 #if defined(CONFIG_MX25)
 	/* Clock Control Module */
 	DEFINE(CCM_CCTL, offsetof(struct ccm_regs, cctl));
diff --git a/board/syteco/jadecpu/Kconfig b/board/syteco/jadecpu/Kconfig
deleted file mode 100644
index 6e9392e..0000000
--- a/board/syteco/jadecpu/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_JADECPU
-
-config SYS_BOARD
-	default "jadecpu"
-
-config SYS_VENDOR
-	default "syteco"
-
-config SYS_SOC
-	default "mb86r0x"
-
-config SYS_CONFIG_NAME
-	default "jadecpu"
-
-endif
diff --git a/board/syteco/jadecpu/MAINTAINERS b/board/syteco/jadecpu/MAINTAINERS
deleted file mode 100644
index b53e7ca..0000000
--- a/board/syteco/jadecpu/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-JADECPU BOARD
-M:	Matthias Weisser <weisserm@arcor.de>
-S:	Maintained
-F:	board/syteco/jadecpu/
-F:	include/configs/jadecpu.h
-F:	configs/jadecpu_defconfig
diff --git a/board/syteco/jadecpu/Makefile b/board/syteco/jadecpu/Makefile
deleted file mode 100644
index 7426436..0000000
--- a/board/syteco/jadecpu/Makefile
+++ /dev/null
@@ -1,13 +0,0 @@
-#
-# (C) Copyright 2003-2008
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# (C) Copyright 2008
-# Stelian Pop <stelian@popies.net>
-# Lead Tech Design <www.leadtechdesign.com>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	+= jadecpu.o
-obj-y	+= lowlevel_init.o
diff --git a/board/syteco/jadecpu/jadecpu.c b/board/syteco/jadecpu/jadecpu.c
deleted file mode 100644
index 6c60a41..0000000
--- a/board/syteco/jadecpu/jadecpu.c
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * (c) 2010 Graf-Syteco, Matthias Weisser
- * <weisserm@arcor.de>
- *
- * (C) Copyright 2007, mycable GmbH
- * Carsten Schneider <cs@mycable.de>, Alexander Bigga <ab@mycable.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <asm/arch/mb86r0x.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-int board_init(void)
-{
-	struct mb86r0x_ccnt * ccnt = (struct mb86r0x_ccnt *)
-					MB86R0x_CCNT_BASE;
-
-	/* We select mode 0 for group 2 and mode 1 for group 4 */
-	writel(0x00000010, &ccnt->cmux_md);
-
-	gd->flags = 0;
-	gd->bd->bi_boot_params = PHYS_SDRAM + PHYS_SDRAM_SIZE - 0x10000;
-
-	icache_enable();
-	dcache_enable();
-
-	return 0;
-}
-
-static void setup_display_power(uint32_t pwr_bit, char *pwm_opts,
-				unsigned long pwm_base)
-{
-	struct mb86r0x_gpio *gpio = (struct mb86r0x_gpio *)
-					MB86R0x_GPIO_BASE;
-	struct mb86r0x_pwm *pwm = (struct mb86r0x_pwm *) pwm_base;
-	const char *e;
-
-	writel(readl(&gpio->gpdr2) | pwr_bit, &gpio->gpdr2);
-
-	e = getenv(pwm_opts);
-	if (e != NULL) {
-		const char *s;
-		uint32_t freq, init;
-
-		freq = 0;
-		init = 0;
-
-		s = strchr(e, 'f');
-		if (s != NULL)
-			freq = simple_strtol(s + 2, NULL, 0);
-
-		s = strchr(e, 'i');
-		if (s != NULL)
-			init = simple_strtol(s + 2, NULL, 0);
-
-		if (freq > 0) {
-			writel(CONFIG_MB86R0x_IOCLK / 1000 / freq,
-				&pwm->bcr);
-			writel(1002, &pwm->tpr);
-			writel(1, &pwm->pr);
-			writel(init * 10 + 1, &pwm->dr);
-			writel(1, &pwm->cr);
-			writel(1, &pwm->sr);
-		}
-	}
-}
-
-int board_late_init(void)
-{
-	struct mb86r0x_gpio *gpio = (struct mb86r0x_gpio *)
-					MB86R0x_GPIO_BASE;
-	uint32_t in_word;
-
-#ifdef CONFIG_VIDEO_MB86R0xGDC
-	/* Check if we have valid display settings and turn on power if so */
-	/* Display 0 */
-	if (getenv("gs_dsp_0_param") || getenv("videomode"))
-		setup_display_power((1 << 3), "gs_dsp_0_pwm",
-					MB86R0x_PWM0_BASE);
-
-	/* The corresponding GPIO is always an output */
-	writel(readl(&gpio->gpddr2) | (1 << 3), &gpio->gpddr2);
-
-	/* Display 1 */
-	if (getenv("gs_dsp_1_param") || getenv("videomode1"))
-		setup_display_power((1 << 4), "gs_dsp_1_pwm",
-					MB86R0x_PWM1_BASE);
-
-	/* The corresponding GPIO is always an output */
-	writel(readl(&gpio->gpddr2) | (1 << 4), &gpio->gpddr2);
-#endif /* CONFIG_VIDEO_MB86R0xGDC */
-
-	/* 5V enable */
-	writel(readl(&gpio->gpdr1) & ~(1 << 5), &gpio->gpdr1);
-	writel(readl(&gpio->gpddr1) | (1 << 5), &gpio->gpddr1);
-
-	/* We have special boot options if told by GPIOs */
-	in_word = readl(&gpio->gpdr1);
-
-	if ((in_word & 0xC0) == 0xC0) {
-		setenv("stdin", "serial");
-		setenv("stdout", "serial");
-		setenv("stderr", "serial");
-		setenv("preboot", "run gs_slow_boot");
-	} else if ((in_word & 0xC0) != 0) {
-		setenv("stdout", "vga");
-		setenv("preboot", "run gs_slow_boot");
-	} else {
-		setenv("stdin", "serial");
-		setenv("stdout", "serial");
-		setenv("stderr", "serial");
-		if (getenv("gs_devel")) {
-			setenv("preboot", "run gs_slow_boot");
-		} else {
-			setenv("preboot", "run gs_fast_boot");
-		}
-	}
-
-	return 0;
-}
-
-int misc_init_r(void)
-{
-	return 0;
-}
-
-/*
- * DRAM configuration
- */
-int dram_init(void)
-{
-	/* dram_init must store complete ramsize in gd->ram_size */
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
-					PHYS_SDRAM_SIZE);
-
-	return 0;
-}
-
-void dram_init_banksize(void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = gd->ram_size;
-}
-
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_SMC911X
-	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
-#endif
-	return rc;
-}
diff --git a/board/syteco/jadecpu/lowlevel_init.S b/board/syteco/jadecpu/lowlevel_init.S
deleted file mode 100644
index 9568cec..0000000
--- a/board/syteco/jadecpu/lowlevel_init.S
+++ /dev/null
@@ -1,249 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2007, mycable GmbH
- * Carsten Schneider <cs@mycable.de>, Alexander Bigga <ab@mycable.de>
- *
- * (C) Copyright 2003, ARM Ltd.
- * Philippe Robin, <philippe.robin@arm.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/macro.h>
-#include <asm/arch/mb86r0x.h>
-#include <generated/asm-offsets.h>
-
-/* Set up the platform, once the cpu has been initialized */
-.globl lowlevel_init
-lowlevel_init:
-/*
- * Initialize Clock Reset Generator (CRG)
- */
-
-	ldr		r0, =MB86R0x_CRG_BASE
-
-	/* Not change the initial value that is set by external pin.*/
-WAIT_PLL:
-	ldr		r2, [r0, #CRG_CRPR]	/* Wait for PLLREADY */
-	tst		r2, #MB86R0x_CRG_CRPR_PLLRDY
-	beq		WAIT_PLL
-
-	/* Set clock gate control */
-	ldr		r1, =CONFIG_SYS_CRG_CRHA_INIT
-	str		r1, [r0, #CRG_CRHA]
-	ldr		r1, =CONFIG_SYS_CRG_CRPA_INIT
-	str		r1, [r0, #CRG_CRPA]
-	ldr		r1, =CONFIG_SYS_CRG_CRPB_INIT
-	str		r1, [r0, #CRG_CRPB]
-	ldr		r1, =CONFIG_SYS_CRG_CRHB_INIT
-	str		r1, [r0, #CRG_CRHB]
-	ldr		r1, =CONFIG_SYS_CRG_CRAM_INIT
-	str		r1, [r0, #CRG_CRAM]
-
-/*
- * Initialize External Bus Interface
- */
-	ldr		r0, =MB86R0x_MEMC_BASE
-
-	ldr		r1, =CONFIG_SYS_MEMC_MCFMODE0_INIT
-	str		r1, [r0, #MEMC_MCFMODE0]
-	ldr		r1, =CONFIG_SYS_MEMC_MCFMODE2_INIT
-	str		r1, [r0, #MEMC_MCFMODE2]
-	ldr		r1, =CONFIG_SYS_MEMC_MCFMODE4_INIT
-	str		r1, [r0, #MEMC_MCFMODE4]
-
-	ldr		r1, =CONFIG_SYS_MEMC_MCFTIM0_INIT
-	str		r1, [r0, #MEMC_MCFTIM0]
-	ldr		r1, =CONFIG_SYS_MEMC_MCFTIM2_INIT
-	str		r1, [r0, #MEMC_MCFTIM2]
-	ldr		r1, =CONFIG_SYS_MEMC_MCFTIM4_INIT
-	str		r1, [r0, #MEMC_MCFTIM4]
-
-	ldr		r1, =CONFIG_SYS_MEMC_MCFAREA0_INIT
-	str		r1, [r0, #MEMC_MCFAREA0]
-	ldr		r1, =CONFIG_SYS_MEMC_MCFAREA2_INIT
-	str		r1, [r0, #MEMC_MCFAREA2]
-	ldr		r1, =CONFIG_SYS_MEMC_MCFAREA4_INIT
-	str		r1, [r0, #MEMC_MCFAREA4]
-
-/*
- * Initialize DDR2 Controller
- */
-
-	/* Wait for PLL LOCK up time or more */
-	wait_timer	20
-
-	/*
-	 * (2) Initialize DDRIF
-	 */
-	ldr	r0, =MB86R0x_DDR2_BASE
-	ldr	r1, =CONFIG_SYS_DDR2_DRIMS_INIT
-	strh	r1, [r0, #DDR2_DRIMS]
-
-	/*
-	 * (3) Wait for 20MCKPs(120nsec) or more
-	 */
-	wait_timer	20
-
-	/*
-	 * (4) IRESET/IUSRRST release
-	 */
-	ldr	r0, =MB86R0x_CCNT_BASE
-	ldr	r1, =CONFIG_SYS_CCNT_CDCRC_INIT_1
-	str	r1, [r0, #CCNT_CDCRC]
-
-	/*
-	 * (5) Wait for 20MCKPs(120nsec) or more
-	 */
-	wait_timer	20
-
-	/*
-	 * (6) IDLLRST release
-	 */
-	ldr	r0, =MB86R0x_CCNT_BASE
-	ldr	r1, =CONFIG_SYS_CCNT_CDCRC_INIT_2
-	str	r1, [r0, #CCNT_CDCRC]
-
-	/*
-	 * (7+8) Wait for 200us(=200000ns) or more (DDR2 Spec)
-	 */
-	wait_timer	33536
-
-	/*
-	 * (9) MCKE ON
-	 */
-	ldr	r0, =MB86R0x_DDR2_BASE
-	ldr	r1, =CONFIG_SYS_DDR2_DRIC1_INIT
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_DRIC2_INIT
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =CONFIG_SYS_DDR2_DRCA_INIT
-	strh	r1, [r0, #DDR2_DRCA]
-	ldr	r1, =MB86R0x_DDR2_DRCI_INIT
-	strh	r1, [r0, #DDR2_DRIC]
-
-	/*
-	 * (10) Initialize SDRAM
-	 */
-
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	wait_timer	67			/* 400ns wait */
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_1
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_1
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_2
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_2
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_3
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_3
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_4
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_4
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_5
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_5
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	wait_timer 200
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_6
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_6
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_7
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_7
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	wait_timer	18			/* 105ns wait */
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_8
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_8
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	wait_timer	200			/* MRS to OCD: 200clock */
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_9
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_9
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC1_10
-	strh	r1, [r0, #DDR2_DRIC1]
-	ldr	r1, =CONFIG_SYS_DDR2_INIT_DRIC2_10
-	strh	r1, [r0, #DDR2_DRIC2]
-	ldr	r1, =MB86R0x_DDR2_DRCI_CMD
-	strh	r1, [r0, #DDR2_DRIC]
-
-	ldr	r1, =CONFIG_SYS_DDR2_DRCM_INIT
-	strh	r1, [r0, #DDR2_DRCM]
-
-	ldr	r1, =CONFIG_SYS_DDR2_DRCST1_INIT
-	strh	r1, [r0, #DDR2_DRCST1]
-
-	ldr	r1, =CONFIG_SYS_DDR2_DRCST2_INIT
-	strh	r1, [r0, #DDR2_DRCST2]
-
-	ldr	r1, =CONFIG_SYS_DDR2_DRCR_INIT
-	strh	r1, [r0, #DDR2_DRCR]
-
-	ldr	r1, =CONFIG_SYS_DDR2_DRCF_INIT
-	strh	r1, [r0, #DDR2_DRCF]
-
-	ldr	r1, =CONFIG_SYS_DDR2_DRASR_INIT
-	strh	r1, [r0, #DDR2_DRASR]
-
-	/*
-	 * (11) ODT setting
-	 */
-	ldr	r1, =CONFIG_SYS_DDR2_DROBS_INIT
-	strh	r1, [r0, #DDR2_DROBS]
-	ldr	r1, =CONFIG_SYS_DDR2_DROABA_INIT
-	strh	r1, [r0, #DDR2_DROABA]
-	ldr	r1, =CONFIG_SYS_DDR2_DRIBSODT1_INIT
-	strh	r1, [r0, #DDR2_DRIBSODT1]
-
-	/*
-	 * (12) Shift to ODTCONT ON (SDRAM side) and DDR2 usual operation mode
-	 */
-	ldr	r1, =CONFIG_SYS_DDR2_DROS_INIT
-	strh	r1, [r0, #DDR2_DROS]
-	ldr	r1, =MB86R0x_DDR2_DRCI_NORMAL
-	strh	r1, [r0, #DDR2_DRIC]
-
-	mov pc, lr
diff --git a/configs/jadecpu_defconfig b/configs/jadecpu_defconfig
deleted file mode 100644
index 4348e0e..0000000
--- a/configs/jadecpu_defconfig
+++ /dev/null
@@ -1,2 +0,0 @@
-CONFIG_ARM=y
-CONFIG_TARGET_JADECPU=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 952ab87..0fc6ac7 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,23 +12,24 @@ The list should be sorted in reverse chronological order.
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
-icecube_5200     powerpc     mpc5xxx        -           -           Wolfgang Denk <wd@denx.de>
-Lite5200         powerpc     mpc5xxx        -           -
-cpci5200         powerpc     mpc5xxx        -           -           Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-mecp5200         powerpc     mpc5xxx        -           -           Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-pf5200           powerpc     mpc5xxx        -           -           Reinhard Arlt <reinhard.arlt@esd-electronics.com>
-PM520            powerpc     mpc5xxx        -           -           Josef Wagner <Wagner@Microsys.de>
-Total5200        powerpc     mpc5xxx        -           -
-CATcenter        powerpc     ppc4xx         -           -
-PPChameleonEVB   powerpc     ppc4xx         -           -           Andrea "llandre" Marson <andrea.marson@dave-tech.it>
-P2020DS          powerpc     mpc85xx        -           -
-P2020COME        powerpc     mpc85xx        -           -           Ira W. Snyder <iws@ovro.caltech.edu>
-P2020RDB         powerpc     mpc85xx        -           -           Poonam Aggrwal <poonam.aggrwal@freescale.com>
-P2010RDB         powerpc     mpc85xx        -           -
-P1020RDB         powerpc     mpc85xx        -           -
-P1011RDB         powerpc     mpc85xx        -           -
-MPC8360EMDS      powerpc     mpc83xx        -           -           Dave Liu <daveliu@freescale.com>
-MPC8360ERDK      powerpc     mpc83xx        -           -           Anton Vorontsov <avorontsov@ru.mvista.com>
+jadecpu          arm         arm926ejs      -           -           Matthias Weisser <weisserm@arcor.de>
+icecube_5200     powerpc     mpc5xxx        37b608a5    2015-01-23  Wolfgang Denk <wd@denx.de>
+Lite5200         powerpc     mpc5xxx        37b608a5    2015-01-23
+cpci5200         powerpc     mpc5xxx        37b608a5    2015-01-23  Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+mecp5200         powerpc     mpc5xxx        37b608a5    2015-01-23  Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+pf5200           powerpc     mpc5xxx        37b608a5    2015-01-23  Reinhard Arlt <reinhard.arlt@esd-electronics.com>
+PM520            powerpc     mpc5xxx        a258e732    2015-01-23  Josef Wagner <Wagner@Microsys.de>
+Total5200        powerpc     mpc5xxx        ad734f7d    2015-01-23
+CATcenter        powerpc     ppc4xx         5344cc1a    2015-01-23
+PPChameleonEVB   powerpc     ppc4xx         5344cc1a    2015-01-23  Andrea "llandre" Marson <andrea.marson@dave-tech.it>
+P2020DS          powerpc     mpc85xx        168dcc6c    2015-01-23
+P2020COME        powerpc     mpc85xx        89123536    2015-01-23  Ira W. Snyder <iws@ovro.caltech.edu>
+P2020RDB         powerpc     mpc85xx        743d4815    2015-01-23  Poonam Aggrwal <poonam.aggrwal@freescale.com>
+P2010RDB         powerpc     mpc85xx        743d4815    2015-01-23
+P1020RDB         powerpc     mpc85xx        743d4815    2015-01-23
+P1011RDB         powerpc     mpc85xx        743d4815    2015-01-23
+MPC8360EMDS      powerpc     mpc83xx        8d1e3cb1    2015-01-23  Dave Liu <daveliu@freescale.com>
+MPC8360ERDK      powerpc     mpc83xx        8d1e3cb1    2015-01-23  Anton Vorontsov <avorontsov@ru.mvista.com>
 P3G4             powerpc     74xx_7xx       d928664f    2015-01-16  Wolfgang Denk <wd@denx.de>
 ZUMA             powerpc     74xx_7xx       d928664f    2015-01-16  Nye Liu <nyet@zumanetworks.com>
 ppmc7xx          powerpc     74xx_7xx       d928664f    2015-01-16
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index af2d47b..22a316b 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -32,7 +32,6 @@ obj-$(CONFIG_VIDEO_IMX25LCDC) += imx25lcdc.o videomodes.o
 obj-$(CONFIG_VIDEO_LCD_HITACHI_TX18D42VM) += hitachi_tx18d42vm_lcd.o
 obj-$(CONFIG_VIDEO_LCD_SSD2828) += ssd2828.o
 obj-$(CONFIG_VIDEO_MB862xx) += mb862xx.o videomodes.o
-obj-$(CONFIG_VIDEO_MB86R0xGDC) += mb86r0xgdc.o videomodes.o
 obj-$(CONFIG_VIDEO_MX3) += mx3fb.o videomodes.o
 obj-$(CONFIG_VIDEO_IPUV3) += mxc_ipuv3_fb.o ipu_common.o ipu_disp.o
 obj-$(CONFIG_VIDEO_MXS) += mxsfb.o videomodes.o
diff --git a/drivers/video/mb86r0xgdc.c b/drivers/video/mb86r0xgdc.c
deleted file mode 100644
index bb7a749..0000000
--- a/drivers/video/mb86r0xgdc.c
+++ /dev/null
@@ -1,168 +0,0 @@
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * mb86r0xgdc.c - Graphic interface for Fujitsu MB86R0x integrated graphic
- * controller.
- */
-
-#include <common.h>
-
-#include <malloc.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <video_fb.h>
-#include "videomodes.h"
-
-/*
- * 4MB (at the end of system RAM)
- */
-#define VIDEO_MEM_SIZE		0x400000
-
-#define FB_SYNC_CLK_INV		(1<<16)	/* pixel clock inverted */
-
-/*
- * Graphic Device
- */
-static GraphicDevice mb86r0x;
-
-static void dsp_init(struct mb86r0x_gdc_dsp *dsp, char *modestr,
-			u32 *videomem)
-{
-	struct ctfb_res_modes var_mode;
-	u32 dcm1, dcm2, dcm3;
-	u16 htp, hdp, hdb, hsp, vtr, vsp, vdp;
-	u8 hsw, vsw;
-	u32 l2m, l2em, l2oa0, l2da0, l2oa1, l2da1;
-	u16 l2dx, l2dy, l2wx, l2wy, l2ww, l2wh;
-	unsigned long div;
-	int bpp;
-
-	bpp = video_get_params(&var_mode, modestr);
-
-	if (bpp == 0) {
-		var_mode.xres = 640;
-		var_mode.yres = 480;
-		var_mode.pixclock = 39721;	/* 25MHz */
-		var_mode.left_margin = 48;
-		var_mode.right_margin = 16;
-		var_mode.upper_margin = 33;
-		var_mode.lower_margin = 10;
-		var_mode.hsync_len = 96;
-		var_mode.vsync_len = 2;
-		var_mode.sync = 0;
-		var_mode.vmode = 0;
-		bpp = 15;
-	}
-
-	/* Fill memory with white */
-	memset(videomem, 0xFF, var_mode.xres * var_mode.yres * 2);
-
-	mb86r0x.winSizeX = var_mode.xres;
-	mb86r0x.winSizeY = var_mode.yres;
-
-	/* LCD base clock is ~ 660MHZ. We do calculations in kHz */
-	div = 660000 / (1000000000L / var_mode.pixclock);
-	if (div > 64)
-		div = 64;
-	if (0 == div)
-		div = 1;
-
-	dcm1 = (div - 1) << 8;
-	dcm2 = 0x00000000;
-	if (var_mode.sync & FB_SYNC_CLK_INV)
-		dcm3 = 0x00000100;
-	else
-		dcm3 = 0x00000000;
-
-	htp = var_mode.left_margin + var_mode.xres +
-		var_mode.hsync_len + var_mode.right_margin;
-	hdp = var_mode.xres;
-	hdb = var_mode.xres;
-	hsp = var_mode.xres + var_mode.right_margin;
-	hsw = var_mode.hsync_len;
-
-	vsw = var_mode.vsync_len;
-	vtr = var_mode.upper_margin + var_mode.yres +
-		var_mode.vsync_len + var_mode.lower_margin;
-	vsp = var_mode.yres + var_mode.lower_margin;
-	vdp = var_mode.yres;
-
-	l2m =	((var_mode.yres - 1) << (0)) |
-		(((var_mode.xres * 2) / 64) << (16)) |
-		((1) << (31));
-
-	l2em = (1 << 0) | (1 << 1);
-
-	l2oa0 = mb86r0x.frameAdrs;
-	l2da0 = mb86r0x.frameAdrs;
-	l2oa1 = mb86r0x.frameAdrs;
-	l2da1 = mb86r0x.frameAdrs;
-	l2dx = 0;
-	l2dy = 0;
-	l2wx = 0;
-	l2wy = 0;
-	l2ww = var_mode.xres;
-	l2wh = var_mode.yres - 1;
-
-	writel(dcm1, &dsp->dcm1);
-	writel(dcm2, &dsp->dcm2);
-	writel(dcm3, &dsp->dcm3);
-
-	writew(htp, &dsp->htp);
-	writew(hdp, &dsp->hdp);
-	writew(hdb, &dsp->hdb);
-	writew(hsp, &dsp->hsp);
-	writeb(hsw, &dsp->hsw);
-
-	writeb(vsw, &dsp->vsw);
-	writew(vtr, &dsp->vtr);
-	writew(vsp, &dsp->vsp);
-	writew(vdp, &dsp->vdp);
-
-	writel(l2m, &dsp->l2m);
-	writel(l2em, &dsp->l2em);
-	writel(l2oa0, &dsp->l2oa0);
-	writel(l2da0, &dsp->l2da0);
-	writel(l2oa1, &dsp->l2oa1);
-	writel(l2da1, &dsp->l2da1);
-	writew(l2dx, &dsp->l2dx);
-	writew(l2dy, &dsp->l2dy);
-	writew(l2wx, &dsp->l2wx);
-	writew(l2wy, &dsp->l2wy);
-	writew(l2ww, &dsp->l2ww);
-	writew(l2wh, &dsp->l2wh);
-
-	writel(dcm1 | (1 << 18) | (1 << 31), &dsp->dcm1);
-}
-
-void *video_hw_init(void)
-{
-	struct mb86r0x_gdc *gdc = (struct mb86r0x_gdc *) MB86R0x_GDC_BASE;
-	GraphicDevice *pGD = &mb86r0x;
-	char *s;
-	u32 *vid;
-
-	memset(pGD, 0, sizeof(GraphicDevice));
-
-	pGD->gdfIndex = GDF_15BIT_555RGB;
-	pGD->gdfBytesPP = 2;
-	pGD->memSize = VIDEO_MEM_SIZE;
-	pGD->frameAdrs = PHYS_SDRAM + PHYS_SDRAM_SIZE - VIDEO_MEM_SIZE;
-
-	vid = (u32 *)pGD->frameAdrs;
-
-	s = getenv("videomode");
-	if (s != NULL)
-		dsp_init(&gdc->dsp0, s, vid);
-
-	s = getenv("videomode1");
-	if (s != NULL)
-		dsp_init(&gdc->dsp1, s, vid);
-
-	return pGD;
-}
diff --git a/include/configs/jadecpu.h b/include/configs/jadecpu.h
deleted file mode 100644
index 8175621..0000000
--- a/include/configs/jadecpu.h
+++ /dev/null
@@ -1,273 +0,0 @@
-/*
- * (C) Copyright 2010
- * Matthias Weisser <weisserm@arcor.de>
- *
- * Configuation settings for the jadecpu board
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_MB86R0x
-#define CONFIG_MB86R0x_IOCLK	get_bus_freq(0)
-#define CONFIG_SYS_TEXT_BASE	0x10000000
-
-
-#define CONFIG_USE_ARCH_MEMCPY
-#define CONFIG_USE_ARCH_MEMSET
-
-#define MACH_TYPE_JADECPU	2636
-
-#define CONFIG_MACH_TYPE MACH_TYPE_JADECPU
-
-/*
- * Environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"gs_fast_boot=setenv bootdelay 5\0" \
-	"gs_slow_boot=setenv bootdelay 10\0" \
-	"bootcmd=dcache off; mw.l 0x40000000 0 1024; usb start;" \
-		"fatls usb 0; fatload usb 0 0x40000000 jadecpu-init.bin;" \
-		"bootelf 0x40000000\0" \
-	""
-
-#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs	*/
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG	1
-#define CONFIG_BOARD_LATE_INIT
-
-/*
- * Compressions
- */
-#define CONFIG_LZO
-
-/*
- * Hardware drivers
- */
-
-/*
- * Serial
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE		(-4)
-#define CONFIG_SYS_NS16550_CLK			get_bus_freq(0)
-#define CONFIG_SYS_NS16550_COM1			0xfffe1000	/* UART 0 */
-#define CONFIG_SYS_NS16550_COM2			0xfff50000	/* UART 2 */
-#define CONFIG_SYS_NS16550_COM3			0xfff51000	/* UART 3 */
-#define CONFIG_SYS_NS16550_COM4			0xfff43000	/* UART 4 */
-
-#define CONFIG_CONS_INDEX	4
-
-/*
- * Ethernet
- */
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE	0x02000000
-#define CONFIG_SMC911X_16_BIT
-
-/*
- * Video
- */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_MB86R0xGDC
-#define CONFIG_SYS_WHITE_ON_BLACK
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_VIDEO_BMP_GZIP
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE  (800*480 + 256*4 + 10*1024)
-#define VIDEO_FB_16BPP_WORD_SWAP
-#define VIDEO_KBD_INIT_FCT		0
-#define VIDEO_TSTC_FCT		serial_stub_tstc
-#define VIDEO_GETC_FCT		serial_stub_getc
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE	1
-#define CONFIG_BOOTP_BOOTPATH		1
-#define CONFIG_BOOTP_GATEWAY		1
-#define CONFIG_BOOTP_HOSTNAME		1
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_SOURCE
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_XIMG
-
-#define CONFIG_CMD_BMP
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_CACHE
-
-#define CONFIG_SYS_HUSH_PARSER
-
-/* USB */
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_SYS_USB_OHCI_REGS_BASE       0xFFF81000
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME       "mb86r0x"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS  1
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-
-/* SDRAM */
-#define CONFIG_NR_DRAM_BANKS	1
-#define PHYS_SDRAM		0x40000000	/* Start address of DDRRAM */
-#define PHYS_SDRAM_SIZE	0x08000000	/* 128 megs */
-
-#define CONFIG_SYS_SDRAM_BASE	PHYS_SDRAM
-#define CONFIG_SYS_INIT_SP_ADDR	0x01008000
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE		0x10000000
-#define CONFIG_SYS_MAX_FLASH_BANKS	1
-#define CONFIG_SYS_MAX_FLASH_SECT	256
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00040000)
-#define CONFIG_ENV_IS_IN_FLASH		1
-#define CONFIG_ENV_SECT_SIZE		(128 * 1024)
-#define CONFIG_ENV_SIZE		(128 * 1024)
-
-/*
- * CFI FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI		1
-#define CONFIG_FLASH_CFI_DRIVER	1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1	/* ~10x faster */
-
-#define CONFIG_SYS_LOAD_ADDR		0x40000000	/* load address */
-
-#define CONFIG_SYS_MEMTEST_START	(PHYS_SDRAM + (512*1024))
-#define CONFIG_SYS_MEMTEST_END		(PHYS_SDRAM + PHYS_SDRAM_SIZE)
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_SYS_PROMPT	"jade> "
-#define CONFIG_SYS_CBSIZE	256
-#define CONFIG_SYS_MAXARGS	16
-#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + \
-				sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP	1
-#define CONFIG_CMDLINE_EDITING	1
-
-#define CONFIG_PREBOOT  ""
-
-#define CONFIG_BOOTDELAY	5
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "boot in %d s\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR	"delaygs"
-#define CONFIG_AUTOBOOT_STOP_STR	"stopgs"
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN	(10 << 20)
-#define CONFIG_SYS_MEM_TOP_HIDE	(4 << 20)
-
-/*
- * Clock reset generator init
- */
-#define CONFIG_SYS_CRG_CRHA_INIT		0xffff
-#define CONFIG_SYS_CRG_CRPA_INIT		0xffff
-#define CONFIG_SYS_CRG_CRPB_INIT		0xfffe
-#define CONFIG_SYS_CRG_CRHB_INIT		0xffff
-#define CONFIG_SYS_CRG_CRAM_INIT		0xffef
-
-/*
- * Memory controller settings
- */
-#define CONFIG_SYS_MEMC_MCFMODE0_INIT	0x00000001	/* 16bit */
-#define CONFIG_SYS_MEMC_MCFMODE2_INIT	0x00000001	/* 16bit */
-#define CONFIG_SYS_MEMC_MCFMODE4_INIT	0x00000021	/* 16bit, Page*/
-#define CONFIG_SYS_MEMC_MCFTIM0_INIT	0x16191008
-#define CONFIG_SYS_MEMC_MCFTIM2_INIT	0x03061008
-#define CONFIG_SYS_MEMC_MCFTIM4_INIT	0x03061804
-#define CONFIG_SYS_MEMC_MCFAREA0_INIT	0x000000c0	/* 0x0c000000 1MB */
-#define CONFIG_SYS_MEMC_MCFAREA2_INIT	0x00000020	/* 0x02000000 1MB */
-#define CONFIG_SYS_MEMC_MCFAREA4_INIT	0x001f0000	/* 0x10000000 32 MB */
-
-/*
- * DDR2 controller init settings
- */
-#define CONFIG_SYS_DDR2_DRIMS_INIT	0x5555
-#define CONFIG_SYS_CCNT_CDCRC_INIT_1	0x00000002
-#define CONFIG_SYS_CCNT_CDCRC_INIT_2	0x00000003
-#define CONFIG_SYS_DDR2_DRIC1_INIT	0x003f
-#define CONFIG_SYS_DDR2_DRIC2_INIT	0x0000
-#define CONFIG_SYS_DDR2_DRCA_INIT	0xc124	/* 512Mbit DDR2SDRAM x 2 */
-#define CONFIG_SYS_DDR2_DRCM_INIT	0x0032
-#define CONFIG_SYS_DDR2_DRCST1_INIT	0x3418
-#define CONFIG_SYS_DDR2_DRCST2_INIT	0x6e32
-#define CONFIG_SYS_DDR2_DRCR_INIT	0x0141
-#define CONFIG_SYS_DDR2_DRCF_INIT	0x0002
-#define CONFIG_SYS_DDR2_DRASR_INIT	0x0001
-#define CONFIG_SYS_DDR2_DROBS_INIT	0x0001
-#define CONFIG_SYS_DDR2_DROABA_INIT	0x0103
-#define CONFIG_SYS_DDR2_DRIBSODT1_INIT	0x003F
-#define CONFIG_SYS_DDR2_DROS_INIT	0x0001
-
-/*
- * DRAM init sequence
- */
-
-/* PALL Command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_1	0x0017
-#define CONFIG_SYS_DDR2_INIT_DRIC2_1	0x0400
-
-/* EMR(2) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_2	0x0006
-#define CONFIG_SYS_DDR2_INIT_DRIC2_2	0x0000
-
-/* EMR(3) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_3	0x0007
-#define CONFIG_SYS_DDR2_INIT_DRIC2_3	0x0000
-
-/* EMR(1) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_4	0x0005
-#define CONFIG_SYS_DDR2_INIT_DRIC2_4	0x0000
-
-/* MRS command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_5	0x0004
-#define CONFIG_SYS_DDR2_INIT_DRIC2_5	0x0532
-
-/* PALL command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_6	0x0017
-#define CONFIG_SYS_DDR2_INIT_DRIC2_6	0x0400
-
-/* REF command 1 */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_7	0x000f
-#define CONFIG_SYS_DDR2_INIT_DRIC2_7	0x0000
-
-/* MRS command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_8	0x0004
-#define CONFIG_SYS_DDR2_INIT_DRIC2_8	0x0432
-
-/* EMR(1) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_9	0x0005
-#define CONFIG_SYS_DDR2_INIT_DRIC2_9	0x0380
-
-/* EMR(1) command */
-#define CONFIG_SYS_DDR2_INIT_DRIC1_10	0x0005
-#define CONFIG_SYS_DDR2_INIT_DRIC2_10	0x0002
-
-#endif	/* __CONFIG_H */
diff --git a/include/serial.h b/include/serial.h
index 66ed12c..3d2e569 100644
--- a/include/serial.h
+++ b/include/serial.h
@@ -29,7 +29,7 @@ extern struct serial_device *default_serial_console(void);
 #if	defined(CONFIG_405GP) || \
 	defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
 	defined(CONFIG_405EX) || defined(CONFIG_440) || \
-	defined(CONFIG_MB86R0x) || defined(CONFIG_MPC5xxx) || \
+	defined(CONFIG_MPC5xxx) || \
 	defined(CONFIG_MPC83xx) || defined(CONFIG_MPC85xx) || \
 	defined(CONFIG_MPC86xx) || defined(CONFIG_SYS_SC520) || \
 	defined(CONFIG_TEGRA) || defined(CONFIG_SYS_COREBOOT) || \