Create PHY Lib for U-Boot

Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme.  The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support

The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).

The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.

We now have MDIO drivers and PHY drivers

An MDIO driver provides:
read
write
reset

A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed

The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()

Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)

We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.

We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,

we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.

Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>

10 files changed, 2218 insertions, 36 deletions

diff --git a/common/Makefile b/common/Makefile
index 4555716..02dbeed 100644
--- a/common/Makefile
+++ b/common/Makefile
@@ -115,6 +115,7 @@ COBJS-$(CONFIG_CMD_MFSL) += cmd_mfsl.o
 COBJS-$(CONFIG_CMD_MG_DISK) += cmd_mgdisk.o
 COBJS-$(CONFIG_MII) += miiphyutil.o
 COBJS-$(CONFIG_CMD_MII) += miiphyutil.o
+COBJS-$(CONFIG_PHYLIB) += miiphyutil.o
 COBJS-$(CONFIG_CMD_MII) += cmd_mii.o
 COBJS-$(CONFIG_CMD_MISC) += cmd_misc.o
 COBJS-$(CONFIG_CMD_MMC) += cmd_mmc.o
diff --git a/common/miiphyutil.c b/common/miiphyutil.c
index 6944ea7..243cae9 100644
--- a/common/miiphyutil.c
+++ b/common/miiphyutil.c
@@ -28,6 +28,7 @@
 
 #include <common.h>
 #include <miiphy.h>
+#include <phy.h>
 
 #include <asm/types.h>
 #include <linux/list.h>
@@ -44,22 +45,13 @@
 #define debug(fmt, args...)
 #endif /* MII_DEBUG */
 
-struct mii_dev {
-	struct list_head link;
-	const char *name;
-	int (*read)(const char *devname, unsigned char addr,
-		     unsigned char reg, unsigned short *value);
-	int (*write)(const char *devname, unsigned char addr,
-		      unsigned char reg, unsigned short value);
-};
-
 static struct list_head mii_devs;
 static struct mii_dev *current_mii;
 
 /*
  * Lookup the mii_dev struct by the registered device name.
  */
-static struct mii_dev *miiphy_get_dev_by_name(const char *devname, int quiet)
+struct mii_dev *miiphy_get_dev_by_name(const char *devname)
 {
 	struct list_head *entry;
 	struct mii_dev *dev;
@@ -75,8 +67,6 @@ static struct mii_dev *miiphy_get_dev_by_name(const char *devname, int quiet)
 			return dev;
 	}
 
-	if (!quiet)
-		printf("No such device: %s\n", devname);
 	return NULL;
 }
 
@@ -90,6 +80,25 @@ void miiphy_init(void)
 	current_mii = NULL;
 }
 
+static int legacy_miiphy_read(struct mii_dev *bus, int addr, int devad, int reg)
+{
+	unsigned short val;
+	int ret;
+	struct legacy_mii_dev *ldev = bus->priv;
+
+	ret = ldev->read(bus->name, addr, reg, &val);
+
+	return ret ? -1 : (int)val;
+}
+
+static int legacy_miiphy_write(struct mii_dev *bus, int addr, int devad,
+				int reg, u16 val)
+{
+	struct legacy_mii_dev *ldev = bus->priv;
+
+	return ldev->write(bus->name, addr, reg, val);
+}
+
 /*****************************************************************************
  *
  * Register read and write MII access routines for the device <name>.
@@ -101,11 +110,11 @@ void miiphy_register(const char *name,
 				    unsigned char reg, unsigned short value))
 {
 	struct mii_dev *new_dev;
+	struct legacy_mii_dev *ldev;
 	unsigned int name_len;
-	char *new_name;
 
 	/* check if we have unique name */
-	new_dev = miiphy_get_dev_by_name(name, 1);
+	new_dev = miiphy_get_dev_by_name(name);
 	if (new_dev) {
 		printf("miiphy_register: non unique device name '%s'\n", name);
 		return;
@@ -113,26 +122,32 @@ void miiphy_register(const char *name,
 
 	/* allocate memory */
 	name_len = strlen(name);
-	new_dev =
-		(struct mii_dev *)malloc(sizeof(struct mii_dev) + name_len + 1);
+	if (name_len > MDIO_NAME_LEN - 1) {
+		/* Hopefully this won't happen, but if it does, we'll know */
+		printf("miiphy_register: MDIO name was longer than %d\n",
+			MDIO_NAME_LEN);
+		return;
+	}
 
-	if (new_dev == NULL) {
+	new_dev = mdio_alloc();
+	ldev = malloc(sizeof(*ldev));
+
+	if (new_dev == NULL || ldev == NULL) {
 		printf("miiphy_register: cannot allocate memory for '%s'\n",
 			name);
 		return;
 	}
-	memset(new_dev, 0, sizeof(struct mii_dev) + name_len);
 
 	/* initalize mii_dev struct fields */
-	INIT_LIST_HEAD(&new_dev->link);
-	new_dev->read = read;
-	new_dev->write = write;
-	new_dev->name = new_name = (char *)(new_dev + 1);
-	strncpy(new_name, name, name_len);
-	new_name[name_len] = '\0';
+	new_dev->read = legacy_miiphy_read;
+	new_dev->write = legacy_miiphy_write;
+	sprintf(new_dev->name, name);
+	ldev->read = read;
+	ldev->write = write;
+	new_dev->priv = ldev;
 
 	debug("miiphy_register: added '%s', read=0x%08lx, write=0x%08lx\n",
-	       new_dev->name, new_dev->read, new_dev->write);
+	       new_dev->name, ldev->read, ldev->write);
 
 	/* add it to the list */
 	list_add_tail(&new_dev->link, &mii_devs);
@@ -141,19 +156,110 @@ void miiphy_register(const char *name,
 		current_mii = new_dev;
 }
 
+struct mii_dev *mdio_alloc(void)
+{
+	struct mii_dev *bus;
+
+	bus = malloc(sizeof(*bus));
+	if (!bus)
+		return bus;
+
+	memset(bus, 0, sizeof(*bus));
+
+	/* initalize mii_dev struct fields */
+	INIT_LIST_HEAD(&bus->link);
+
+	return bus;
+}
+
+int mdio_register(struct mii_dev *bus)
+{
+	if (!bus || !bus->name || !bus->read || !bus->write)
+		return -1;
+
+	/* check if we have unique name */
+	if (miiphy_get_dev_by_name(bus->name)) {
+		printf("mdio_register: non unique device name '%s'\n",
+			bus->name);
+		return -1;
+	}
+
+	/* add it to the list */
+	list_add_tail(&bus->link, &mii_devs);
+
+	if (!current_mii)
+		current_mii = bus;
+
+	return 0;
+}
+
+void mdio_list_devices(void)
+{
+	struct list_head *entry;
+
+	list_for_each(entry, &mii_devs) {
+		int i;
+		struct mii_dev *bus = list_entry(entry, struct mii_dev, link);
+
+		printf("%s:\n", bus->name);
+
+		for (i = 0; i < PHY_MAX_ADDR; i++) {
+			struct phy_device *phydev = bus->phymap[i];
+
+			if (phydev) {
+				printf("%d - %s", i, phydev->drv->name);
+
+				if (phydev->dev)
+					printf(" <--> %s\n", phydev->dev->name);
+				else
+					printf("\n");
+			}
+		}
+	}
+}
+
 int miiphy_set_current_dev(const char *devname)
 {
 	struct mii_dev *dev;
 
-	dev = miiphy_get_dev_by_name(devname, 0);
+	dev = miiphy_get_dev_by_name(devname);
 	if (dev) {
 		current_mii = dev;
 		return 0;
 	}
 
+	printf("No such device: %s\n", devname);
+
 	return 1;
 }
 
+struct mii_dev *mdio_get_current_dev(void)
+{
+	return current_mii;
+}
+
+struct phy_device *mdio_phydev_for_ethname(const char *ethname)
+{
+	struct list_head *entry;
+	struct mii_dev *bus;
+
+	list_for_each(entry, &mii_devs) {
+		int i;
+		bus = list_entry(entry, struct mii_dev, link);
+
+		for (i = 0; i < PHY_MAX_ADDR; i++) {
+			if (!bus->phymap[i] || !bus->phymap[i]->dev)
+				continue;
+
+			if (strcmp(bus->phymap[i]->dev->name, ethname) == 0)
+				return bus->phymap[i];
+		}
+	}
+
+	printf("%s is not a known ethernet\n", ethname);
+	return NULL;
+}
+
 const char *miiphy_get_current_dev(void)
 {
 	if (current_mii)
@@ -187,13 +293,15 @@ static struct mii_dev *miiphy_get_active_dev(const char *devname)
 int miiphy_read(const char *devname, unsigned char addr, unsigned char reg,
 		 unsigned short *value)
 {
-	struct mii_dev *dev;
+	struct mii_dev *bus;
 
-	dev = miiphy_get_active_dev(devname);
-	if (dev)
-		return dev->read(devname, addr, reg, value);
+	bus = miiphy_get_active_dev(devname);
+	if (bus)
+		*value = bus->read(bus, addr, MDIO_DEVAD_NONE, reg);
+	else
+		return 1;
 
-	return 1;
+	return (*value < 0) ? 1 : 0;
 }
 
 /*****************************************************************************
@@ -207,11 +315,11 @@ int miiphy_read(const char *devname, unsigned char addr, unsigned char reg,
 int miiphy_write(const char *devname, unsigned char addr, unsigned char reg,
 		  unsigned short value)
 {
-	struct mii_dev *dev;
+	struct mii_dev *bus;
 
-	dev = miiphy_get_active_dev(devname);
-	if (dev)
-		return dev->write(devname, addr, reg, value);
+	bus = miiphy_get_active_dev(devname);
+	if (bus)
+		return bus->write(bus, addr, MDIO_DEVAD_NONE, reg, value);
 
 	return 1;
 }
@@ -279,6 +387,7 @@ int miiphy_info(const char *devname, unsigned char addr, unsigned int *oui,
 	return 0;
 }
 
+#ifndef CONFIG_PHYLIB
 /*****************************************************************************
  *
  * Reset the PHY.
@@ -322,6 +431,7 @@ int miiphy_reset(const char *devname, unsigned char addr)
 	}
 	return 0;
 }
+#endif /* !PHYLIB */
 
 /*****************************************************************************
  *
@@ -352,7 +462,6 @@ int miiphy_speed(const char *devname, unsigned char addr)
 	if (btsr != 0xFFFF &&
 			(btsr & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)))
 		return _1000BASET;
-
 #endif /* CONFIG_PHY_GIGE */
 
 	/* Check Basic Management Control Register first. */
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index bba8901..609a22f 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -27,6 +27,8 @@ LIB	:= $(obj)libphy.o
 
 COBJS-$(CONFIG_BITBANGMII) += miiphybb.o
 COBJS-$(CONFIG_MV88E61XX_SWITCH) += mv88e61xx.o
+COBJS-$(CONFIG_PHYLIB) += phy.o
+COBJS-$(CONFIG_PHYLIB_10G) += generic_10g.o
 
 COBJS	:= $(COBJS-y)
 SRCS	:= $(COBJS:.o=.c)
diff --git a/drivers/net/phy/generic_10g.c b/drivers/net/phy/generic_10g.c
new file mode 100644
index 0000000..315c508
--- /dev/null
+++ b/drivers/net/phy/generic_10g.c
@@ -0,0 +1,105 @@
+/*
+ * Generic PHY Management code
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ *
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ * Based loosely off of Linux's PHY Lib
+ */
+
+#include <config.h>
+#include <common.h>
+#include <miiphy.h>
+#include <phy.h>
+
+int gen10g_shutdown(struct phy_device *phydev)
+{
+	return 0;
+}
+
+int gen10g_startup(struct phy_device *phydev)
+{
+	int devad, reg;
+	u32 mmd_mask = phydev->mmds;
+
+	phydev->link = 1;
+
+	/* For now just lie and say it's 10G all the time */
+	phydev->speed = SPEED_10000;
+	phydev->duplex = DUPLEX_FULL;
+
+	for (devad = 0; mmd_mask; devad++, mmd_mask = mmd_mask >> 1) {
+		if (!mmd_mask & 1)
+			continue;
+
+		/* Read twice because link state is latched and a
+		 * read moves the current state into the register */
+		phy_read(phydev, devad, MDIO_STAT1);
+		reg = phy_read(phydev, devad, MDIO_STAT1);
+		if (reg < 0 || !(reg & MDIO_STAT1_LSTATUS))
+			phydev->link = 0;
+	}
+
+	return 0;
+}
+
+int gen10g_discover_mmds(struct phy_device *phydev)
+{
+	int mmd, stat2, devs1, devs2;
+
+	/* Assume PHY must have at least one of PMA/PMD, WIS, PCS, PHY
+	 * XS or DTE XS; give up if none is present. */
+	for (mmd = 1; mmd <= 5; mmd++) {
+		/* Is this MMD present? */
+		stat2 = phy_read(phydev, mmd, MDIO_STAT2);
+		if (stat2 < 0 ||
+			(stat2 & MDIO_STAT2_DEVPRST) != MDIO_STAT2_DEVPRST_VAL)
+			continue;
+
+		/* It should tell us about all the other MMDs */
+		devs1 = phy_read(phydev, mmd, MDIO_DEVS1);
+		devs2 = phy_read(phydev, mmd, MDIO_DEVS2);
+		if (devs1 < 0 || devs2 < 0)
+			continue;
+
+		phydev->mmds = devs1 | (devs2 << 16);
+		return 0;
+	}
+
+	return 0;
+}
+
+int gen10g_config(struct phy_device *phydev)
+{
+	/* For now, assume 10000baseT. Fill in later */
+	phydev->supported = phydev->advertising = SUPPORTED_10000baseT_Full;
+
+	return gen10g_discover_mmds(phydev);
+}
+
+struct phy_driver gen10g_driver = {
+	.uid		= 0xffffffff,
+	.mask		= 0xffffffff,
+	.name		= "Generic 10G PHY",
+	.features	= 0,
+	.config		= gen10g_config,
+	.startup	= gen10g_startup,
+	.shutdown	= gen10g_shutdown,
+};
+
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
new file mode 100644
index 0000000..919011d
--- /dev/null
+++ b/drivers/net/phy/phy.c
@@ -0,0 +1,724 @@
+/*
+ * Generic PHY Management code
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ *
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ * Based loosely off of Linux's PHY Lib
+ */
+
+#include <config.h>
+#include <common.h>
+#include <malloc.h>
+#include <net.h>
+#include <command.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <errno.h>
+
+/* Generic PHY support and helper functions */
+
+/**
+ * genphy_config_advert - sanitize and advertise auto-negotation parameters
+ * @phydev: target phy_device struct
+ *
+ * Description: Writes MII_ADVERTISE with the appropriate values,
+ *   after sanitizing the values to make sure we only advertise
+ *   what is supported.  Returns < 0 on error, 0 if the PHY's advertisement
+ *   hasn't changed, and > 0 if it has changed.
+ */
+int genphy_config_advert(struct phy_device *phydev)
+{
+	u32 advertise;
+	int oldadv, adv;
+	int err, changed = 0;
+
+	/* Only allow advertising what
+	 * this PHY supports */
+	phydev->advertising &= phydev->supported;
+	advertise = phydev->advertising;
+
+	/* Setup standard advertisement */
+	oldadv = adv = phy_read(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE);
+
+	if (adv < 0)
+		return adv;
+
+	adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4 | ADVERTISE_PAUSE_CAP |
+		 ADVERTISE_PAUSE_ASYM);
+	if (advertise & ADVERTISED_10baseT_Half)
+		adv |= ADVERTISE_10HALF;
+	if (advertise & ADVERTISED_10baseT_Full)
+		adv |= ADVERTISE_10FULL;
+	if (advertise & ADVERTISED_100baseT_Half)
+		adv |= ADVERTISE_100HALF;
+	if (advertise & ADVERTISED_100baseT_Full)
+		adv |= ADVERTISE_100FULL;
+	if (advertise & ADVERTISED_Pause)
+		adv |= ADVERTISE_PAUSE_CAP;
+	if (advertise & ADVERTISED_Asym_Pause)
+		adv |= ADVERTISE_PAUSE_ASYM;
+
+	if (adv != oldadv) {
+		err = phy_write(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE, adv);
+
+		if (err < 0)
+			return err;
+		changed = 1;
+	}
+
+	/* Configure gigabit if it's supported */
+	if (phydev->supported & (SUPPORTED_1000baseT_Half |
+				SUPPORTED_1000baseT_Full)) {
+		oldadv = adv = phy_read(phydev, MDIO_DEVAD_NONE, MII_CTRL1000);
+
+		if (adv < 0)
+			return adv;
+
+		adv &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF);
+		if (advertise & SUPPORTED_1000baseT_Half)
+			adv |= ADVERTISE_1000HALF;
+		if (advertise & SUPPORTED_1000baseT_Full)
+			adv |= ADVERTISE_1000FULL;
+
+		if (adv != oldadv) {
+			err = phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000,
+					adv);
+
+			if (err < 0)
+				return err;
+			changed = 1;
+		}
+	}
+
+	return changed;
+}
+
+
+/**
+ * genphy_setup_forced - configures/forces speed/duplex from @phydev
+ * @phydev: target phy_device struct
+ *
+ * Description: Configures MII_BMCR to force speed/duplex
+ *   to the values in phydev. Assumes that the values are valid.
+ */
+int genphy_setup_forced(struct phy_device *phydev)
+{
+	int err;
+	int ctl = 0;
+
+	phydev->pause = phydev->asym_pause = 0;
+
+	if (SPEED_1000 == phydev->speed)
+		ctl |= BMCR_SPEED1000;
+	else if (SPEED_100 == phydev->speed)
+		ctl |= BMCR_SPEED100;
+
+	if (DUPLEX_FULL == phydev->duplex)
+		ctl |= BMCR_FULLDPLX;
+
+	err = phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl);
+
+	return err;
+}
+
+
+/**
+ * genphy_restart_aneg - Enable and Restart Autonegotiation
+ * @phydev: target phy_device struct
+ */
+int genphy_restart_aneg(struct phy_device *phydev)
+{
+	int ctl;
+
+	ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+	if (ctl < 0)
+		return ctl;
+
+	ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
+
+	/* Don't isolate the PHY if we're negotiating */
+	ctl &= ~(BMCR_ISOLATE);
+
+	ctl = phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl);
+
+	return ctl;
+}
+
+
+/**
+ * genphy_config_aneg - restart auto-negotiation or write BMCR
+ * @phydev: target phy_device struct
+ *
+ * Description: If auto-negotiation is enabled, we configure the
+ *   advertising, and then restart auto-negotiation.  If it is not
+ *   enabled, then we write the BMCR.
+ */
+int genphy_config_aneg(struct phy_device *phydev)
+{
+	int result;
+
+	if (AUTONEG_ENABLE != phydev->autoneg)
+		return genphy_setup_forced(phydev);
+
+	result = genphy_config_advert(phydev);
+
+	if (result < 0) /* error */
+		return result;
+
+	if (result == 0) {
+		/* Advertisment hasn't changed, but maybe aneg was never on to
+		 * begin with?  Or maybe phy was isolated? */
+		int ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+		if (ctl < 0)
+			return ctl;
+
+		if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE))
+			result = 1; /* do restart aneg */
+	}
+
+	/* Only restart aneg if we are advertising something different
+	 * than we were before.	 */
+	if (result > 0)
+		result = genphy_restart_aneg(phydev);
+
+	return result;
+}
+
+/**
+ * genphy_update_link - update link status in @phydev
+ * @phydev: target phy_device struct
+ *
+ * Description: Update the value in phydev->link to reflect the
+ *   current link value.  In order to do this, we need to read
+ *   the status register twice, keeping the second value.
+ */
+int genphy_update_link(struct phy_device *phydev)
+{
+	unsigned int mii_reg;
+
+	/*
+	 * Wait if the link is up, and autonegotiation is in progress
+	 * (ie - we're capable and it's not done)
+	 */
+	mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+	/*
+	 * If we already saw the link up, and it hasn't gone down, then
+	 * we don't need to wait for autoneg again
+	 */
+	if (phydev->link && mii_reg & BMSR_LSTATUS)
+		return 0;
+
+	if ((mii_reg & BMSR_ANEGCAPABLE) && !(mii_reg & BMSR_ANEGCOMPLETE)) {
+		int i = 0;
+
+		printf("%s Waiting for PHY auto negotiation to complete",
+			phydev->dev->name);
+		while (!(mii_reg & BMSR_ANEGCOMPLETE)) {
+			/*
+			 * Timeout reached ?
+			 */
+			if (i > PHY_ANEG_TIMEOUT) {
+				printf(" TIMEOUT !\n");
+				phydev->link = 0;
+				return 0;
+			}
+
+			if (ctrlc()) {
+				puts("user interrupt!\n");
+				phydev->link = 0;
+				return -EINTR;
+			}
+
+			if ((i++ % 500) == 0)
+				printf(".");
+
+			udelay(1000);	/* 1 ms */
+			mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+		}
+		printf(" done\n");
+		phydev->link = 1;
+	} else {
+		/* Read the link a second time to clear the latched state */
+		mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+		if (mii_reg & BMSR_LSTATUS)
+			phydev->link = 1;
+		else
+			phydev->link = 0;
+	}
+
+	return 0;
+}
+
+/*
+ * Generic function which updates the speed and duplex.  If
+ * autonegotiation is enabled, it uses the AND of the link
+ * partner's advertised capabilities and our advertised
+ * capabilities.  If autonegotiation is disabled, we use the
+ * appropriate bits in the control register.
+ *
+ * Stolen from Linux's mii.c and phy_device.c
+ */
+static int genphy_parse_link(struct phy_device *phydev)
+{
+	int mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+	/* We're using autonegotiation */
+	if (mii_reg & BMSR_ANEGCAPABLE) {
+		u32 lpa = 0;
+		u32 gblpa = 0;
+
+		/* Check for gigabit capability */
+		if (mii_reg & BMSR_ERCAP) {
+			/* We want a list of states supported by
+			 * both PHYs in the link
+			 */
+			gblpa = phy_read(phydev, MDIO_DEVAD_NONE, MII_STAT1000);
+			gblpa &= phy_read(phydev,
+					MDIO_DEVAD_NONE, MII_CTRL1000) << 2;
+		}
+
+		/* Set the baseline so we only have to set them
+		 * if they're different
+		 */
+		phydev->speed = SPEED_10;
+		phydev->duplex = DUPLEX_HALF;
+
+		/* Check the gigabit fields */
+		if (gblpa & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) {
+			phydev->speed = SPEED_1000;
+
+			if (gblpa & PHY_1000BTSR_1000FD)
+				phydev->duplex = DUPLEX_FULL;
+
+			/* We're done! */
+			return 0;
+		}
+
+		lpa = phy_read(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE);
+		lpa &= phy_read(phydev, MDIO_DEVAD_NONE, MII_LPA);
+
+		if (lpa & (LPA_100FULL | LPA_100HALF)) {
+			phydev->speed = SPEED_100;
+
+			if (lpa & LPA_100FULL)
+				phydev->duplex = DUPLEX_FULL;
+
+		} else if (lpa & LPA_10FULL)
+			phydev->duplex = DUPLEX_FULL;
+	} else {
+		u32 bmcr = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+		phydev->speed = SPEED_10;
+		phydev->duplex = DUPLEX_HALF;
+
+		if (bmcr & BMCR_FULLDPLX)
+			phydev->duplex = DUPLEX_FULL;
+
+		if (bmcr & BMCR_SPEED1000)
+			phydev->speed = SPEED_1000;
+		else if (bmcr & BMCR_SPEED100)
+			phydev->speed = SPEED_100;
+	}
+
+	return 0;
+}
+
+int genphy_config(struct phy_device *phydev)
+{
+	int val;
+	u32 features;
+
+	/* For now, I'll claim that the generic driver supports
+	 * all possible port types */
+	features = (SUPPORTED_TP | SUPPORTED_MII
+			| SUPPORTED_AUI | SUPPORTED_FIBRE |
+			SUPPORTED_BNC);
+
+	/* Do we support autonegotiation? */
+	val = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+	if (val < 0)
+		return val;
+
+	if (val & BMSR_ANEGCAPABLE)
+		features |= SUPPORTED_Autoneg;
+
+	if (val & BMSR_100FULL)
+		features |= SUPPORTED_100baseT_Full;
+	if (val & BMSR_100HALF)
+		features |= SUPPORTED_100baseT_Half;
+	if (val & BMSR_10FULL)
+		features |= SUPPORTED_10baseT_Full;
+	if (val & BMSR_10HALF)
+		features |= SUPPORTED_10baseT_Half;
+
+	if (val & BMSR_ESTATEN) {
+		val = phy_read(phydev, MDIO_DEVAD_NONE, MII_ESTATUS);
+
+		if (val < 0)
+			return val;
+
+		if (val & ESTATUS_1000_TFULL)
+			features |= SUPPORTED_1000baseT_Full;
+		if (val & ESTATUS_1000_THALF)
+			features |= SUPPORTED_1000baseT_Half;
+	}
+
+	phydev->supported = features;
+	phydev->advertising = features;
+
+	genphy_config_aneg(phydev);
+
+	return 0;
+}
+
+int genphy_startup(struct phy_device *phydev)
+{
+	genphy_update_link(phydev);
+	genphy_parse_link(phydev);
+
+	return 0;
+}
+
+int genphy_shutdown(struct phy_device *phydev)
+{
+	return 0;
+}
+
+static struct phy_driver genphy_driver = {
+	.uid		= 0xffffffff,
+	.mask		= 0xffffffff,
+	.name		= "Generic PHY",
+	.features	= 0,
+	.config		= genphy_config,
+	.startup	= genphy_startup,
+	.shutdown	= genphy_shutdown,
+};
+
+static LIST_HEAD(phy_drivers);
+
+int phy_init(void)
+{
+	return 0;
+}
+
+int phy_register(struct phy_driver *drv)
+{
+	INIT_LIST_HEAD(&drv->list);
+	list_add_tail(&drv->list, &phy_drivers);
+
+	return 0;
+}
+
+int phy_probe(struct phy_device *phydev)
+{
+	int err = 0;
+
+	phydev->advertising = phydev->supported = phydev->drv->features;
+	phydev->mmds = phydev->drv->mmds;
+
+	if (phydev->drv->probe)
+		err = phydev->drv->probe(phydev);
+
+	return err;
+}
+
+static struct phy_driver *generic_for_interface(phy_interface_t interface)
+{
+#ifdef CONFIG_PHYLIB_10G
+	if (is_10g_interface(interface))
+		return &gen10g_driver;
+#endif
+
+	return &genphy_driver;
+}
+
+struct phy_driver *get_phy_driver(struct phy_device *phydev,
+				phy_interface_t interface)
+{
+	struct list_head *entry;
+	int phy_id = phydev->phy_id;
+	struct phy_driver *drv = NULL;
+
+	list_for_each(entry, &phy_drivers) {
+		drv = list_entry(entry, struct phy_driver, list);
+		if ((drv->uid & drv->mask) == (phy_id & drv->mask))
+			return drv;
+	}
+
+	/* If we made it here, there's no driver for this PHY */
+	return generic_for_interface(interface);
+}
+
+struct phy_device *phy_device_create(struct mii_dev *bus, int addr, int phy_id,
+					phy_interface_t interface)
+{
+	struct phy_device *dev;
+
+	/* We allocate the device, and initialize the
+	 * default values */
+	dev = malloc(sizeof(*dev));
+	if (!dev) {
+		printf("Failed to allocate PHY device for %s:%d\n",
+			bus->name, addr);
+		return NULL;
+	}
+
+	memset(dev, 0, sizeof(*dev));
+
+	dev->duplex = -1;
+	dev->link = 1;
+	dev->interface = interface;
+
+	dev->autoneg = AUTONEG_ENABLE;
+
+	dev->addr = addr;
+	dev->phy_id = phy_id;
+	dev->bus = bus;
+
+	dev->drv = get_phy_driver(dev, interface);
+
+	phy_probe(dev);
+
+	bus->phymap[addr] = dev;
+
+	return dev;
+}
+
+/**
+ * get_phy_id - reads the specified addr for its ID.
+ * @bus: the target MII bus
+ * @addr: PHY address on the MII bus
+ * @phy_id: where to store the ID retrieved.
+ *
+ * Description: Reads the ID registers of the PHY at @addr on the
+ *   @bus, stores it in @phy_id and returns zero on success.
+ */
+int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
+{
+	int phy_reg;
+
+	/* Grab the bits from PHYIR1, and put them
+	 * in the upper half */
+	phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);
+
+	if (phy_reg < 0)
+		return -EIO;
+
+	*phy_id = (phy_reg & 0xffff) << 16;
+
+	/* Grab the bits from PHYIR2, and put them in the lower half */
+	phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);
+
+	if (phy_reg < 0)
+		return -EIO;
+
+	*phy_id |= (phy_reg & 0xffff);
+
+	return 0;
+}
+
+/**
+ * get_phy_device - reads the specified PHY device and returns its @phy_device struct
+ * @bus: the target MII bus
+ * @addr: PHY address on the MII bus
+ *
+ * Description: Reads the ID registers of the PHY at @addr on the
+ *   @bus, then allocates and returns the phy_device to represent it.
+ */
+struct phy_device *get_phy_device(struct mii_dev *bus, int addr,
+				phy_interface_t interface)
+{
+	u32 phy_id = 0x1fffffff;
+	int i;
+	int r;
+
+	/* If we have one, return the existing device, with new interface */
+	if (bus->phymap[addr]) {
+		bus->phymap[addr]->interface = interface;
+
+		return bus->phymap[addr];
+	}
+
+	/* Try Standard (ie Clause 22) access */
+	r = get_phy_id(bus, addr, MDIO_DEVAD_NONE, &phy_id);
+	if (r)
+		return NULL;
+
+	/* If the PHY ID is mostly f's, we didn't find anything */
+	if ((phy_id & 0x1fffffff) != 0x1fffffff)
+		return phy_device_create(bus, addr, phy_id, interface);
+
+	/* Otherwise we have to try Clause 45 */
+	for (i = 1; i < 5; i++) {
+		r = get_phy_id(bus, addr, i, &phy_id);
+		if (r)
+			return NULL;
+
+		/* If the phy_id is mostly Fs, there is no device there */
+		if ((phy_id & 0x1fffffff) != 0x1fffffff)
+			break;
+	}
+
+	return phy_device_create(bus, addr, phy_id, interface);
+}
+
+int phy_reset(struct phy_device *phydev)
+{
+	int reg;
+	int timeout = 500;
+	int devad = MDIO_DEVAD_NONE;
+
+#ifdef CONFIG_PHYLIB_10G
+	/* If it's 10G, we need to issue reset through one of the MMDs */
+	if (is_10g_interface(phydev->interface)) {
+		if (!phydev->mmds)
+			gen10g_discover_mmds(phydev);
+
+		devad = ffs(phydev->mmds) - 1;
+	}
+#endif
+
+	reg = phy_read(phydev, devad, MII_BMCR);
+	if (reg < 0) {
+		debug("PHY status read failed\n");
+		return -1;
+	}
+
+	reg |= BMCR_RESET;
+
+	if (phy_write(phydev, devad, MII_BMCR, reg) < 0) {
+		debug("PHY reset failed\n");
+		return -1;
+	}
+
+#ifdef CONFIG_PHY_RESET_DELAY
+	udelay(CONFIG_PHY_RESET_DELAY);	/* Intel LXT971A needs this */
+#endif
+	/*
+	 * Poll the control register for the reset bit to go to 0 (it is
+	 * auto-clearing).  This should happen within 0.5 seconds per the
+	 * IEEE spec.
+	 */
+	while ((reg & BMCR_RESET) && timeout--) {
+		reg = phy_read(phydev, devad, MII_BMCR);
+
+		if (reg < 0) {
+			debug("PHY status read failed\n");
+			return -1;
+		}
+		udelay(1000);
+	}
+
+	if (reg & BMCR_RESET) {
+		puts("PHY reset timed out\n");
+		return -1;
+	}
+
+	return 0;
+}
+
+int miiphy_reset(const char *devname, unsigned char addr)
+{
+	struct mii_dev *bus = miiphy_get_dev_by_name(devname);
+	struct phy_device *phydev;
+
+	/*
+	 * miiphy_reset was only used on standard PHYs, so we'll fake it here.
+	 * If later code tries to connect with the right interface, this will
+	 * be corrected by get_phy_device in phy_connect()
+	 */
+	phydev = get_phy_device(bus, addr, PHY_INTERFACE_MODE_MII);
+
+	return phy_reset(phydev);
+}
+
+struct phy_device *phy_connect(struct mii_dev *bus, int addr,
+				struct eth_device *dev,
+				phy_interface_t interface)
+{
+	struct phy_device *phydev;
+
+	/* Reset the bus */
+	bus->reset(bus);
+
+	/* Wait 15ms to make sure the PHY has come out of hard reset */
+	udelay(15000);
+
+	phydev = get_phy_device(bus, addr, interface);
+
+	if (!phydev) {
+		printf("Could not get PHY for %s:%d\n", bus->name, addr);
+
+		return NULL;
+	}
+
+	/* Soft Reset the PHY */
+	phy_reset(phydev);
+
+	if (phydev->dev)
+		printf("%s:%d is connected to %s.  Reconnecting to %s\n",
+			bus->name, addr, phydev->dev->name, dev->name);
+
+	phydev->dev = dev;
+
+	printf("%s connected to %s\n", dev->name, phydev->drv->name);
+
+	return phydev;
+}
+
+int phy_startup(struct phy_device *phydev)
+{
+	if (phydev->drv->startup)
+		phydev->drv->startup(phydev);
+
+	return 0;
+}
+
+static int __board_phy_config(struct phy_device *phydev)
+{
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+	__attribute__((weak, alias("__board_phy_config")));
+
+int phy_config(struct phy_device *phydev)
+{
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	/* Invoke an optional board-specific helper */
+	board_phy_config(phydev);
+
+	return 0;
+}
+
+int phy_shutdown(struct phy_device *phydev)
+{
+	if (phydev->drv->shutdown)
+		phydev->drv->shutdown(phydev);
+
+	return 0;
+}
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
new file mode 100644
index 0000000..fcb20fe
--- /dev/null
+++ b/include/linux/ethtool.h
@@ -0,0 +1,721 @@
+/*
+ * ethtool.h: Defines for Linux ethtool.
+ *
+ * Copyright (C) 1998 David S. Miller (davem@redhat.com)
+ * Copyright 2001 Jeff Garzik <jgarzik@pobox.com>
+ * Portions Copyright 2001 Sun Microsystems (thockin@sun.com)
+ * Portions Copyright 2002 Intel (eli.kupermann@intel.com,
+ *                                christopher.leech@intel.com,
+ *                                scott.feldman@intel.com)
+ * Portions Copyright (C) Sun Microsystems 2008
+ */
+
+#ifndef _LINUX_ETHTOOL_H
+#define _LINUX_ETHTOOL_H
+
+#include <linux/types.h>
+
+/* This should work for both 32 and 64 bit userland. */
+struct ethtool_cmd {
+	__u32	cmd;
+	__u32	supported;	/* Features this interface supports */
+	__u32	advertising;	/* Features this interface advertises */
+	__u16	speed;		/* The forced speed, 10Mb, 100Mb, gigabit */
+	__u8	duplex;		/* Duplex, half or full */
+	__u8	port;		/* Which connector port */
+	__u8	phy_address;
+	__u8	transceiver;	/* Which transceiver to use */
+	__u8	autoneg;	/* Enable or disable autonegotiation */
+	__u8	mdio_support;
+	__u32	maxtxpkt;	/* Tx pkts before generating tx int */
+	__u32	maxrxpkt;	/* Rx pkts before generating rx int */
+	__u16	speed_hi;
+	__u8	eth_tp_mdix;
+	__u8	reserved2;
+	__u32	lp_advertising;	/* Features the link partner advertises */
+	__u32	reserved[2];
+};
+
+static inline void ethtool_cmd_speed_set(struct ethtool_cmd *ep,
+						__u32 speed)
+{
+
+	ep->speed = (__u16)speed;
+	ep->speed_hi = (__u16)(speed >> 16);
+}
+
+static inline __u32 ethtool_cmd_speed(struct ethtool_cmd *ep)
+{
+	return (ep->speed_hi << 16) | ep->speed;
+}
+
+#define ETHTOOL_FWVERS_LEN	32
+#define ETHTOOL_BUSINFO_LEN	32
+/* these strings are set to whatever the driver author decides... */
+struct ethtool_drvinfo {
+	__u32	cmd;
+	char	driver[32];	/* driver short name, "tulip", "eepro100" */
+	char	version[32];	/* driver version string */
+	char	fw_version[ETHTOOL_FWVERS_LEN];	/* firmware version string */
+	char	bus_info[ETHTOOL_BUSINFO_LEN];	/* Bus info for this IF. */
+				/* For PCI devices, use pci_name(pci_dev). */
+	char	reserved1[32];
+	char	reserved2[12];
+				/*
+				 * Some struct members below are filled in
+				 * using ops->get_sset_count().  Obtaining
+				 * this info from ethtool_drvinfo is now
+				 * deprecated; Use ETHTOOL_GSSET_INFO
+				 * instead.
+				 */
+	__u32	n_priv_flags;	/* number of flags valid in ETHTOOL_GPFLAGS */
+	__u32	n_stats;	/* number of u64's from ETHTOOL_GSTATS */
+	__u32	testinfo_len;
+	__u32	eedump_len;	/* Size of data from ETHTOOL_GEEPROM (bytes) */
+	__u32	regdump_len;	/* Size of data from ETHTOOL_GREGS (bytes) */
+};
+
+#define SOPASS_MAX	6
+/* wake-on-lan settings */
+struct ethtool_wolinfo {
+	__u32	cmd;
+	__u32	supported;
+	__u32	wolopts;
+	__u8	sopass[SOPASS_MAX]; /* SecureOn(tm) password */
+};
+
+/* for passing single values */
+struct ethtool_value {
+	__u32	cmd;
+	__u32	data;
+};
+
+/* for passing big chunks of data */
+struct ethtool_regs {
+	__u32	cmd;
+	__u32	version; /* driver-specific, indicates different chips/revs */
+	__u32	len; /* bytes */
+	__u8	data[0];
+};
+
+/* for passing EEPROM chunks */
+struct ethtool_eeprom {
+	__u32	cmd;
+	__u32	magic;
+	__u32	offset; /* in bytes */
+	__u32	len; /* in bytes */
+	__u8	data[0];
+};
+
+/* for configuring coalescing parameters of chip */
+struct ethtool_coalesce {
+	__u32	cmd;	/* ETHTOOL_{G,S}COALESCE */
+
+	/* How many usecs to delay an RX interrupt after
+	 * a packet arrives.  If 0, only rx_max_coalesced_frames
+	 * is used.
+	 */
+	__u32	rx_coalesce_usecs;
+
+	/* How many packets to delay an RX interrupt after
+	 * a packet arrives.  If 0, only rx_coalesce_usecs is
+	 * used.  It is illegal to set both usecs and max frames
+	 * to zero as this would cause RX interrupts to never be
+	 * generated.
+	 */
+	__u32	rx_max_coalesced_frames;
+
+	/* Same as above two parameters, except that these values
+	 * apply while an IRQ is being serviced by the host.  Not
+	 * all cards support this feature and the values are ignored
+	 * in that case.
+	 */
+	__u32	rx_coalesce_usecs_irq;
+	__u32	rx_max_coalesced_frames_irq;
+
+	/* How many usecs to delay a TX interrupt after
+	 * a packet is sent.  If 0, only tx_max_coalesced_frames
+	 * is used.
+	 */
+	__u32	tx_coalesce_usecs;
+
+	/* How many packets to delay a TX interrupt after
+	 * a packet is sent.  If 0, only tx_coalesce_usecs is
+	 * used.  It is illegal to set both usecs and max frames
+	 * to zero as this would cause TX interrupts to never be
+	 * generated.
+	 */
+	__u32	tx_max_coalesced_frames;
+
+	/* Same as above two parameters, except that these values
+	 * apply while an IRQ is being serviced by the host.  Not
+	 * all cards support this feature and the values are ignored
+	 * in that case.
+	 */
+	__u32	tx_coalesce_usecs_irq;
+	__u32	tx_max_coalesced_frames_irq;
+
+	/* How many usecs to delay in-memory statistics
+	 * block updates.  Some drivers do not have an in-memory
+	 * statistic block, and in such cases this value is ignored.
+	 * This value must not be zero.
+	 */
+	__u32	stats_block_coalesce_usecs;
+
+	/* Adaptive RX/TX coalescing is an algorithm implemented by
+	 * some drivers to improve latency under low packet rates and
+	 * improve throughput under high packet rates.  Some drivers
+	 * only implement one of RX or TX adaptive coalescing.  Anything
+	 * not implemented by the driver causes these values to be
+	 * silently ignored.
+	 */
+	__u32	use_adaptive_rx_coalesce;
+	__u32	use_adaptive_tx_coalesce;
+
+	/* When the packet rate (measured in packets per second)
+	 * is below pkt_rate_low, the {rx,tx}_*_low parameters are
+	 * used.
+	 */
+	__u32	pkt_rate_low;
+	__u32	rx_coalesce_usecs_low;
+	__u32	rx_max_coalesced_frames_low;
+	__u32	tx_coalesce_usecs_low;
+	__u32	tx_max_coalesced_frames_low;
+
+	/* When the packet rate is below pkt_rate_high but above
+	 * pkt_rate_low (both measured in packets per second) the
+	 * normal {rx,tx}_* coalescing parameters are used.
+	 */
+
+	/* When the packet rate is (measured in packets per second)
+	 * is above pkt_rate_high, the {rx,tx}_*_high parameters are
+	 * used.
+	 */
+	__u32	pkt_rate_high;
+	__u32	rx_coalesce_usecs_high;
+	__u32	rx_max_coalesced_frames_high;
+	__u32	tx_coalesce_usecs_high;
+	__u32	tx_max_coalesced_frames_high;
+
+	/* How often to do adaptive coalescing packet rate sampling,
+	 * measured in seconds.  Must not be zero.
+	 */
+	__u32	rate_sample_interval;
+};
+
+/* for configuring RX/TX ring parameters */
+struct ethtool_ringparam {
+	__u32	cmd;	/* ETHTOOL_{G,S}RINGPARAM */
+
+	/* Read only attributes.  These indicate the maximum number
+	 * of pending RX/TX ring entries the driver will allow the
+	 * user to set.
+	 */
+	__u32	rx_max_pending;
+	__u32	rx_mini_max_pending;
+	__u32	rx_jumbo_max_pending;
+	__u32	tx_max_pending;
+
+	/* Values changeable by the user.  The valid values are
+	 * in the range 1 to the "*_max_pending" counterpart above.
+	 */
+	__u32	rx_pending;
+	__u32	rx_mini_pending;
+	__u32	rx_jumbo_pending;
+	__u32	tx_pending;
+};
+
+/* for configuring link flow control parameters */
+struct ethtool_pauseparam {
+	__u32	cmd;	/* ETHTOOL_{G,S}PAUSEPARAM */
+
+	/* If the link is being auto-negotiated (via ethtool_cmd.autoneg
+	 * being true) the user may set 'autonet' here non-zero to have the
+	 * pause parameters be auto-negotiated too.  In such a case, the
+	 * {rx,tx}_pause values below determine what capabilities are
+	 * advertised.
+	 *
+	 * If 'autoneg' is zero or the link is not being auto-negotiated,
+	 * then {rx,tx}_pause force the driver to use/not-use pause
+	 * flow control.
+	 */
+	__u32	autoneg;
+	__u32	rx_pause;
+	__u32	tx_pause;
+};
+
+#define ETH_GSTRING_LEN		32
+enum ethtool_stringset {
+	ETH_SS_TEST		= 0,
+	ETH_SS_STATS,
+	ETH_SS_PRIV_FLAGS,
+	ETH_SS_NTUPLE_FILTERS,
+	ETH_SS_FEATURES,
+};
+
+/* for passing string sets for data tagging */
+struct ethtool_gstrings {
+	__u32	cmd;		/* ETHTOOL_GSTRINGS */
+	__u32	string_set;	/* string set id e.c. ETH_SS_TEST, etc*/
+	__u32	len;		/* number of strings in the string set */
+	__u8	data[0];
+};
+
+struct ethtool_sset_info {
+	__u32	cmd;		/* ETHTOOL_GSSET_INFO */
+	__u32	reserved;
+	__u64	sset_mask;	/* input: each bit selects an sset to query */
+				/* output: each bit a returned sset */
+	__u32	data[0];	/* ETH_SS_xxx count, in order, based on bits
+				   in sset_mask.  One bit implies one
+				   __u32, two bits implies two
+				   __u32's, etc. */
+};
+
+enum ethtool_test_flags {
+	ETH_TEST_FL_OFFLINE	= (1 << 0),	/* online / offline */
+	ETH_TEST_FL_FAILED	= (1 << 1),	/* test passed / failed */
+};
+
+/* for requesting NIC test and getting results*/
+struct ethtool_test {
+	__u32	cmd;		/* ETHTOOL_TEST */
+	__u32	flags;		/* ETH_TEST_FL_xxx */
+	__u32	reserved;
+	__u32	len;		/* result length, in number of u64 elements */
+	__u64	data[0];
+};
+
+/* for dumping NIC-specific statistics */
+struct ethtool_stats {
+	__u32	cmd;		/* ETHTOOL_GSTATS */
+	__u32	n_stats;	/* number of u64's being returned */
+	__u64	data[0];
+};
+
+struct ethtool_perm_addr {
+	__u32	cmd;		/* ETHTOOL_GPERMADDR */
+	__u32	size;
+	__u8	data[0];
+};
+
+/* boolean flags controlling per-interface behavior characteristics.
+ * When reading, the flag indicates whether or not a certain behavior
+ * is enabled/present.  When writing, the flag indicates whether
+ * or not the driver should turn on (set) or off (clear) a behavior.
+ *
+ * Some behaviors may read-only (unconditionally absent or present).
+ * If such is the case, return EINVAL in the set-flags operation if the
+ * flag differs from the read-only value.
+ */
+enum ethtool_flags {
+	ETH_FLAG_TXVLAN		= (1 << 7),	/* TX VLAN offload enabled */
+	ETH_FLAG_RXVLAN		= (1 << 8),	/* RX VLAN offload enabled */
+	ETH_FLAG_LRO		= (1 << 15),	/* LRO is enabled */
+	ETH_FLAG_NTUPLE		= (1 << 27),	/* N-tuple filters enabled */
+	ETH_FLAG_RXHASH		= (1 << 28),
+};
+
+/* The following structures are for supporting RX network flow
+ * classification and RX n-tuple configuration. Note, all multibyte
+ * fields, e.g., ip4src, ip4dst, psrc, pdst, spi, etc. are expected to
+ * be in network byte order.
+ */
+
+/**
+ * struct ethtool_tcpip4_spec - flow specification for TCP/IPv4 etc.
+ * @ip4src: Source host
+ * @ip4dst: Destination host
+ * @psrc: Source port
+ * @pdst: Destination port
+ * @tos: Type-of-service
+ *
+ * This can be used to specify a TCP/IPv4, UDP/IPv4 or SCTP/IPv4 flow.
+ */
+struct ethtool_tcpip4_spec {
+	__be32	ip4src;
+	__be32	ip4dst;
+	__be16	psrc;
+	__be16	pdst;
+	__u8    tos;
+};
+
+/**
+ * struct ethtool_ah_espip4_spec - flow specification for IPsec/IPv4
+ * @ip4src: Source host
+ * @ip4dst: Destination host
+ * @spi: Security parameters index
+ * @tos: Type-of-service
+ *
+ * This can be used to specify an IPsec transport or tunnel over IPv4.
+ */
+struct ethtool_ah_espip4_spec {
+	__be32	ip4src;
+	__be32	ip4dst;
+	__be32	spi;
+	__u8    tos;
+};
+
+#define	ETH_RX_NFC_IP4	1
+
+/**
+ * struct ethtool_usrip4_spec - general flow specification for IPv4
+ * @ip4src: Source host
+ * @ip4dst: Destination host
+ * @l4_4_bytes: First 4 bytes of transport (layer 4) header
+ * @tos: Type-of-service
+ * @ip_ver: Value must be %ETH_RX_NFC_IP4; mask must be 0
+ * @proto: Transport protocol number; mask must be 0
+ */
+struct ethtool_usrip4_spec {
+	__be32	ip4src;
+	__be32	ip4dst;
+	__be32	l4_4_bytes;
+	__u8    tos;
+	__u8    ip_ver;
+	__u8    proto;
+};
+
+
+/**
+ * struct ethtool_rxfh_indir - command to get or set RX flow hash indirection
+ * @cmd: Specific command number - %ETHTOOL_GRXFHINDIR or %ETHTOOL_SRXFHINDIR
+ * @size: On entry, the array size of the user buffer.  On return from
+ *	%ETHTOOL_GRXFHINDIR, the array size of the hardware indirection table.
+ * @ring_index: RX ring/queue index for each hash value
+ */
+struct ethtool_rxfh_indir {
+	__u32	cmd;
+	__u32	size;
+	__u32	ring_index[0];
+};
+
+#define ETHTOOL_FLASH_MAX_FILENAME	128
+enum ethtool_flash_op_type {
+	ETHTOOL_FLASH_ALL_REGIONS	= 0,
+};
+
+/* for passing firmware flashing related parameters */
+struct ethtool_flash {
+	__u32	cmd;
+	__u32	region;
+	char	data[ETHTOOL_FLASH_MAX_FILENAME];
+};
+
+/* for returning and changing feature sets */
+
+/**
+ * struct ethtool_get_features_block - block with state of 32 features
+ * @available: mask of changeable features
+ * @requested: mask of features requested to be enabled if possible
+ * @active: mask of currently enabled features
+ * @never_changed: mask of features not changeable for any device
+ */
+struct ethtool_get_features_block {
+	__u32	available;
+	__u32	requested;
+	__u32	active;
+	__u32	never_changed;
+};
+
+/**
+ * struct ethtool_gfeatures - command to get state of device's features
+ * @cmd: command number = %ETHTOOL_GFEATURES
+ * @size: in: number of elements in the features[] array;
+ *       out: number of elements in features[] needed to hold all features
+ * @features: state of features
+ */
+struct ethtool_gfeatures {
+	__u32	cmd;
+	__u32	size;
+	struct ethtool_get_features_block features[0];
+};
+
+/**
+ * struct ethtool_set_features_block - block with request for 32 features
+ * @valid: mask of features to be changed
+ * @requested: values of features to be changed
+ */
+struct ethtool_set_features_block {
+	__u32	valid;
+	__u32	requested;
+};
+
+/**
+ * struct ethtool_sfeatures - command to request change in device's features
+ * @cmd: command number = %ETHTOOL_SFEATURES
+ * @size: array size of the features[] array
+ * @features: feature change masks
+ */
+struct ethtool_sfeatures {
+	__u32	cmd;
+	__u32	size;
+	struct ethtool_set_features_block features[0];
+};
+
+/*
+ * %ETHTOOL_SFEATURES changes features present in features[].valid to the
+ * values of corresponding bits in features[].requested. Bits in .requested
+ * not set in .valid or not changeable are ignored.
+ *
+ * Returns %EINVAL when .valid contains undefined or never-changable bits
+ * or size is not equal to required number of features words (32-bit blocks).
+ * Returns >= 0 if request was completed; bits set in the value mean:
+ *   %ETHTOOL_F_UNSUPPORTED - there were bits set in .valid that are not
+ *	changeable (not present in %ETHTOOL_GFEATURES' features[].available)
+ *	those bits were ignored.
+ *   %ETHTOOL_F_WISH - some or all changes requested were recorded but the
+ *      resulting state of bits masked by .valid is not equal to .requested.
+ *      Probably there are other device-specific constraints on some features
+ *      in the set. When %ETHTOOL_F_UNSUPPORTED is set, .valid is considered
+ *      here as though ignored bits were cleared.
+ *   %ETHTOOL_F_COMPAT - some or all changes requested were made by calling
+ *      compatibility functions. Requested offload state cannot be properly
+ *      managed by kernel.
+ *
+ * Meaning of bits in the masks are obtained by %ETHTOOL_GSSET_INFO (number of
+ * bits in the arrays - always multiple of 32) and %ETHTOOL_GSTRINGS commands
+ * for ETH_SS_FEATURES string set. First entry in the table corresponds to least
+ * significant bit in features[0] fields. Empty strings mark undefined features.
+ */
+enum ethtool_sfeatures_retval_bits {
+	ETHTOOL_F_UNSUPPORTED__BIT,
+	ETHTOOL_F_WISH__BIT,
+	ETHTOOL_F_COMPAT__BIT,
+};
+
+#define ETHTOOL_F_UNSUPPORTED   (1 << ETHTOOL_F_UNSUPPORTED__BIT)
+#define ETHTOOL_F_WISH          (1 << ETHTOOL_F_WISH__BIT)
+#define ETHTOOL_F_COMPAT        (1 << ETHTOOL_F_COMPAT__BIT)
+
+/* CMDs currently supported */
+#define ETHTOOL_GSET		0x00000001 /* Get settings. */
+#define ETHTOOL_SSET		0x00000002 /* Set settings. */
+#define ETHTOOL_GDRVINFO	0x00000003 /* Get driver info. */
+#define ETHTOOL_GREGS		0x00000004 /* Get NIC registers. */
+#define ETHTOOL_GWOL		0x00000005 /* Get wake-on-lan options. */
+#define ETHTOOL_SWOL		0x00000006 /* Set wake-on-lan options. */
+#define ETHTOOL_GMSGLVL		0x00000007 /* Get driver message level */
+#define ETHTOOL_SMSGLVL		0x00000008 /* Set driver msg level. */
+#define ETHTOOL_NWAY_RST	0x00000009 /* Restart autonegotiation. */
+/* Get link status for host, i.e. whether the interface *and* the
+ * physical port (if there is one) are up (ethtool_value). */
+#define ETHTOOL_GLINK		0x0000000a
+#define ETHTOOL_GEEPROM		0x0000000b /* Get EEPROM data */
+#define ETHTOOL_SEEPROM		0x0000000c /* Set EEPROM data. */
+#define ETHTOOL_GCOALESCE	0x0000000e /* Get coalesce config */
+#define ETHTOOL_SCOALESCE	0x0000000f /* Set coalesce config. */
+#define ETHTOOL_GRINGPARAM	0x00000010 /* Get ring parameters */
+#define ETHTOOL_SRINGPARAM	0x00000011 /* Set ring parameters. */
+#define ETHTOOL_GPAUSEPARAM	0x00000012 /* Get pause parameters */
+#define ETHTOOL_SPAUSEPARAM	0x00000013 /* Set pause parameters. */
+#define ETHTOOL_GRXCSUM		0x00000014 /* Get RX hw csum enable (ethtool_value) */
+#define ETHTOOL_SRXCSUM		0x00000015 /* Set RX hw csum enable (ethtool_value) */
+#define ETHTOOL_GTXCSUM		0x00000016 /* Get TX hw csum enable (ethtool_value) */
+#define ETHTOOL_STXCSUM		0x00000017 /* Set TX hw csum enable (ethtool_value) */
+#define ETHTOOL_GSG		0x00000018 /* Get scatter-gather enable
+					    * (ethtool_value) */
+#define ETHTOOL_SSG		0x00000019 /* Set scatter-gather enable
+					    * (ethtool_value). */
+#define ETHTOOL_TEST		0x0000001a /* execute NIC self-test. */
+#define ETHTOOL_GSTRINGS	0x0000001b /* get specified string set */
+#define ETHTOOL_PHYS_ID		0x0000001c /* identify the NIC */
+#define ETHTOOL_GSTATS		0x0000001d /* get NIC-specific statistics */
+#define ETHTOOL_GTSO		0x0000001e /* Get TSO enable (ethtool_value) */
+#define ETHTOOL_STSO		0x0000001f /* Set TSO enable (ethtool_value) */
+#define ETHTOOL_GPERMADDR	0x00000020 /* Get permanent hardware address */
+#define ETHTOOL_GUFO		0x00000021 /* Get UFO enable (ethtool_value) */
+#define ETHTOOL_SUFO		0x00000022 /* Set UFO enable (ethtool_value) */
+#define ETHTOOL_GGSO		0x00000023 /* Get GSO enable (ethtool_value) */
+#define ETHTOOL_SGSO		0x00000024 /* Set GSO enable (ethtool_value) */
+#define ETHTOOL_GFLAGS		0x00000025 /* Get flags bitmap(ethtool_value) */
+#define ETHTOOL_SFLAGS		0x00000026 /* Set flags bitmap(ethtool_value) */
+#define ETHTOOL_GPFLAGS		0x00000027 /* Get driver-private flags bitmap */
+#define ETHTOOL_SPFLAGS		0x00000028 /* Set driver-private flags bitmap */
+
+#define ETHTOOL_GRXFH		0x00000029 /* Get RX flow hash configuration */
+#define ETHTOOL_SRXFH		0x0000002a /* Set RX flow hash configuration */
+#define ETHTOOL_GGRO		0x0000002b /* Get GRO enable (ethtool_value) */
+#define ETHTOOL_SGRO		0x0000002c /* Set GRO enable (ethtool_value) */
+#define ETHTOOL_GRXRINGS	0x0000002d /* Get RX rings available for LB */
+#define ETHTOOL_GRXCLSRLCNT	0x0000002e /* Get RX class rule count */
+#define ETHTOOL_GRXCLSRULE	0x0000002f /* Get RX classification rule */
+#define ETHTOOL_GRXCLSRLALL	0x00000030 /* Get all RX classification rule */
+#define ETHTOOL_SRXCLSRLDEL	0x00000031 /* Delete RX classification rule */
+#define ETHTOOL_SRXCLSRLINS	0x00000032 /* Insert RX classification rule */
+#define ETHTOOL_FLASHDEV	0x00000033 /* Flash firmware to device */
+#define ETHTOOL_RESET		0x00000034 /* Reset hardware */
+#define ETHTOOL_SRXNTUPLE	0x00000035 /* Add an n-tuple filter to device */
+#define ETHTOOL_GRXNTUPLE	0x00000036 /* Get n-tuple filters from device */
+#define ETHTOOL_GSSET_INFO	0x00000037 /* Get string set info */
+#define ETHTOOL_GRXFHINDIR	0x00000038 /* Get RX flow hash indir'n table */
+#define ETHTOOL_SRXFHINDIR	0x00000039 /* Set RX flow hash indir'n table */
+
+#define ETHTOOL_GFEATURES	0x0000003a /* Get device offload settings */
+#define ETHTOOL_SFEATURES	0x0000003b /* Change device offload settings */
+
+/* compatibility with older code */
+#define SPARC_ETH_GSET		ETHTOOL_GSET
+#define SPARC_ETH_SSET		ETHTOOL_SSET
+
+/* Indicates what features are supported by the interface. */
+#define SUPPORTED_10baseT_Half		(1 << 0)
+#define SUPPORTED_10baseT_Full		(1 << 1)
+#define SUPPORTED_100baseT_Half		(1 << 2)
+#define SUPPORTED_100baseT_Full		(1 << 3)
+#define SUPPORTED_1000baseT_Half	(1 << 4)
+#define SUPPORTED_1000baseT_Full	(1 << 5)
+#define SUPPORTED_Autoneg		(1 << 6)
+#define SUPPORTED_TP			(1 << 7)
+#define SUPPORTED_AUI			(1 << 8)
+#define SUPPORTED_MII			(1 << 9)
+#define SUPPORTED_FIBRE			(1 << 10)
+#define SUPPORTED_BNC			(1 << 11)
+#define SUPPORTED_10000baseT_Full	(1 << 12)
+#define SUPPORTED_Pause			(1 << 13)
+#define SUPPORTED_Asym_Pause		(1 << 14)
+#define SUPPORTED_2500baseX_Full	(1 << 15)
+#define SUPPORTED_Backplane		(1 << 16)
+#define SUPPORTED_1000baseKX_Full	(1 << 17)
+#define SUPPORTED_10000baseKX4_Full	(1 << 18)
+#define SUPPORTED_10000baseKR_Full	(1 << 19)
+#define SUPPORTED_10000baseR_FEC	(1 << 20)
+
+/* Indicates what features are advertised by the interface. */
+#define ADVERTISED_10baseT_Half		(1 << 0)
+#define ADVERTISED_10baseT_Full		(1 << 1)
+#define ADVERTISED_100baseT_Half	(1 << 2)
+#define ADVERTISED_100baseT_Full	(1 << 3)
+#define ADVERTISED_1000baseT_Half	(1 << 4)
+#define ADVERTISED_1000baseT_Full	(1 << 5)
+#define ADVERTISED_Autoneg		(1 << 6)
+#define ADVERTISED_TP			(1 << 7)
+#define ADVERTISED_AUI			(1 << 8)
+#define ADVERTISED_MII			(1 << 9)
+#define ADVERTISED_FIBRE		(1 << 10)
+#define ADVERTISED_BNC			(1 << 11)
+#define ADVERTISED_10000baseT_Full	(1 << 12)
+#define ADVERTISED_Pause		(1 << 13)
+#define ADVERTISED_Asym_Pause		(1 << 14)
+#define ADVERTISED_2500baseX_Full	(1 << 15)
+#define ADVERTISED_Backplane		(1 << 16)
+#define ADVERTISED_1000baseKX_Full	(1 << 17)
+#define ADVERTISED_10000baseKX4_Full	(1 << 18)
+#define ADVERTISED_10000baseKR_Full	(1 << 19)
+#define ADVERTISED_10000baseR_FEC	(1 << 20)
+
+/* The following are all involved in forcing a particular link
+ * mode for the device for setting things.  When getting the
+ * devices settings, these indicate the current mode and whether
+ * it was foced up into this mode or autonegotiated.
+ */
+
+/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */
+#define SPEED_10		10
+#define SPEED_100		100
+#define SPEED_1000		1000
+#define SPEED_2500		2500
+#define SPEED_10000		10000
+
+/* Duplex, half or full. */
+#define DUPLEX_HALF		0x00
+#define DUPLEX_FULL		0x01
+
+/* Which connector port. */
+#define PORT_TP			0x00
+#define PORT_AUI		0x01
+#define PORT_MII		0x02
+#define PORT_FIBRE		0x03
+#define PORT_BNC		0x04
+#define PORT_DA			0x05
+#define PORT_NONE		0xef
+#define PORT_OTHER		0xff
+
+/* Which transceiver to use. */
+#define XCVR_INTERNAL		0x00
+#define XCVR_EXTERNAL		0x01
+#define XCVR_DUMMY1		0x02
+#define XCVR_DUMMY2		0x03
+#define XCVR_DUMMY3		0x04
+
+/* Enable or disable autonegotiation.  If this is set to enable,
+ * the forced link modes above are completely ignored.
+ */
+#define AUTONEG_DISABLE		0x00
+#define AUTONEG_ENABLE		0x01
+
+/* Mode MDI or MDI-X */
+#define ETH_TP_MDI_INVALID	0x00
+#define ETH_TP_MDI		0x01
+#define ETH_TP_MDI_X		0x02
+
+/* Wake-On-Lan options. */
+#define WAKE_PHY		(1 << 0)
+#define WAKE_UCAST		(1 << 1)
+#define WAKE_MCAST		(1 << 2)
+#define WAKE_BCAST		(1 << 3)
+#define WAKE_ARP		(1 << 4)
+#define WAKE_MAGIC		(1 << 5)
+#define WAKE_MAGICSECURE	(1 << 6) /* only meaningful if WAKE_MAGIC */
+
+/* L2-L4 network traffic flow types */
+#define	TCP_V4_FLOW	0x01	/* hash or spec (tcp_ip4_spec) */
+#define	UDP_V4_FLOW	0x02	/* hash or spec (udp_ip4_spec) */
+#define	SCTP_V4_FLOW	0x03	/* hash or spec (sctp_ip4_spec) */
+#define	AH_ESP_V4_FLOW	0x04	/* hash only */
+#define	TCP_V6_FLOW	0x05	/* hash only */
+#define	UDP_V6_FLOW	0x06	/* hash only */
+#define	SCTP_V6_FLOW	0x07	/* hash only */
+#define	AH_ESP_V6_FLOW	0x08	/* hash only */
+#define	AH_V4_FLOW	0x09	/* hash or spec (ah_ip4_spec) */
+#define	ESP_V4_FLOW	0x0a	/* hash or spec (esp_ip4_spec) */
+#define	AH_V6_FLOW	0x0b	/* hash only */
+#define	ESP_V6_FLOW	0x0c	/* hash only */
+#define	IP_USER_FLOW	0x0d	/* spec only (usr_ip4_spec) */
+#define	IPV4_FLOW	0x10	/* hash only */
+#define	IPV6_FLOW	0x11	/* hash only */
+#define	ETHER_FLOW	0x12	/* spec only (ether_spec) */
+
+/* L3-L4 network traffic flow hash options */
+#define	RXH_L2DA	(1 << 1)
+#define	RXH_VLAN	(1 << 2)
+#define	RXH_L3_PROTO	(1 << 3)
+#define	RXH_IP_SRC	(1 << 4)
+#define	RXH_IP_DST	(1 << 5)
+#define	RXH_L4_B_0_1	(1 << 6) /* src port in case of TCP/UDP/SCTP */
+#define	RXH_L4_B_2_3	(1 << 7) /* dst port in case of TCP/UDP/SCTP */
+#define	RXH_DISCARD	(1 << 31)
+
+#define	RX_CLS_FLOW_DISC	0xffffffffffffffffULL
+
+/* Reset flags */
+/* The reset() operation must clear the flags for the components which
+ * were actually reset.  On successful return, the flags indicate the
+ * components which were not reset, either because they do not exist
+ * in the hardware or because they cannot be reset independently.  The
+ * driver must never reset any components that were not requested.
+ */
+enum ethtool_reset_flags {
+	/* These flags represent components dedicated to the interface
+	 * the command is addressed to.  Shift any flag left by
+	 * ETH_RESET_SHARED_SHIFT to reset a shared component of the
+	 * same type.
+	 */
+	ETH_RESET_MGMT		= 1 << 0,	/* Management processor */
+	ETH_RESET_IRQ		= 1 << 1,	/* Interrupt requester */
+	ETH_RESET_DMA		= 1 << 2,	/* DMA engine */
+	ETH_RESET_FILTER	= 1 << 3,	/* Filtering/flow direction */
+	ETH_RESET_OFFLOAD	= 1 << 4,	/* Protocol offload */
+	ETH_RESET_MAC		= 1 << 5,	/* Media access controller */
+	ETH_RESET_PHY		= 1 << 6,	/* Transceiver/PHY */
+	ETH_RESET_RAM		= 1 << 7,	/* RAM shared between
+						 * multiple components */
+
+	ETH_RESET_DEDICATED	= 0x0000ffff,	/* All components dedicated to
+						 * this interface */
+	ETH_RESET_ALL		= 0xffffffff,	/* All components used by this
+						 * interface, even if shared */
+};
+#define ETH_RESET_SHARED_SHIFT	16
+
+#endif /* _LINUX_ETHTOOL_H */
diff --git a/include/linux/mdio.h b/include/linux/mdio.h
new file mode 100644
index 0000000..022d772
--- /dev/null
+++ b/include/linux/mdio.h
@@ -0,0 +1,278 @@
+/*
+ * linux/mdio.h: definitions for MDIO (clause 45) transceivers
+ * Copyright 2006-2009 Solarflare Communications Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation, incorporated herein by reference.
+ */
+
+#ifndef __LINUX_MDIO_H__
+#define __LINUX_MDIO_H__
+
+#include <linux/mii.h>
+
+/* MDIO Manageable Devices (MMDs). */
+#define MDIO_MMD_PMAPMD		1	/* Physical Medium Attachment/
+					 * Physical Medium Dependent */
+#define MDIO_MMD_WIS		2	/* WAN Interface Sublayer */
+#define MDIO_MMD_PCS		3	/* Physical Coding Sublayer */
+#define MDIO_MMD_PHYXS		4	/* PHY Extender Sublayer */
+#define MDIO_MMD_DTEXS		5	/* DTE Extender Sublayer */
+#define MDIO_MMD_TC		6	/* Transmission Convergence */
+#define MDIO_MMD_AN		7	/* Auto-Negotiation */
+#define MDIO_MMD_C22EXT		29	/* Clause 22 extension */
+#define MDIO_MMD_VEND1		30	/* Vendor specific 1 */
+#define MDIO_MMD_VEND2		31	/* Vendor specific 2 */
+
+/* Generic MDIO registers. */
+#define MDIO_CTRL1		MII_BMCR
+#define MDIO_STAT1		MII_BMSR
+#define MDIO_DEVID1		MII_PHYSID1
+#define MDIO_DEVID2		MII_PHYSID2
+#define MDIO_SPEED		4	/* Speed ability */
+#define MDIO_DEVS1		5	/* Devices in package */
+#define MDIO_DEVS2		6
+#define MDIO_CTRL2		7	/* 10G control 2 */
+#define MDIO_STAT2		8	/* 10G status 2 */
+#define MDIO_PMA_TXDIS		9	/* 10G PMA/PMD transmit disable */
+#define MDIO_PMA_RXDET		10	/* 10G PMA/PMD receive signal detect */
+#define MDIO_PMA_EXTABLE	11	/* 10G PMA/PMD extended ability */
+#define MDIO_PKGID1		14	/* Package identifier */
+#define MDIO_PKGID2		15
+#define MDIO_AN_ADVERTISE	16	/* AN advertising (base page) */
+#define MDIO_AN_LPA		19	/* AN LP abilities (base page) */
+#define MDIO_PHYXS_LNSTAT	24	/* PHY XGXS lane state */
+
+/* Media-dependent registers. */
+#define MDIO_PMA_10GBT_SWAPPOL	130	/* 10GBASE-T pair swap & polarity */
+#define MDIO_PMA_10GBT_TXPWR	131	/* 10GBASE-T TX power control */
+#define MDIO_PMA_10GBT_SNR	133	/* 10GBASE-T SNR margin, lane A.
+					 * Lanes B-D are numbered 134-136. */
+#define MDIO_PMA_10GBR_FECABLE	170	/* 10GBASE-R FEC ability */
+#define MDIO_PCS_10GBX_STAT1	24	/* 10GBASE-X PCS status 1 */
+#define MDIO_PCS_10GBRT_STAT1	32	/* 10GBASE-R/-T PCS status 1 */
+#define MDIO_PCS_10GBRT_STAT2	33	/* 10GBASE-R/-T PCS status 2 */
+#define MDIO_AN_10GBT_CTRL	32	/* 10GBASE-T auto-negotiation control */
+#define MDIO_AN_10GBT_STAT	33	/* 10GBASE-T auto-negotiation status */
+#define MDIO_AN_EEE_ADV		60	/* EEE advertisement */
+
+/* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */
+#define MDIO_PMA_LASI_RXCTRL	0x9000	/* RX_ALARM control */
+#define MDIO_PMA_LASI_TXCTRL	0x9001	/* TX_ALARM control */
+#define MDIO_PMA_LASI_CTRL	0x9002	/* LASI control */
+#define MDIO_PMA_LASI_RXSTAT	0x9003	/* RX_ALARM status */
+#define MDIO_PMA_LASI_TXSTAT	0x9004	/* TX_ALARM status */
+#define MDIO_PMA_LASI_STAT	0x9005	/* LASI status */
+
+/* Control register 1. */
+/* Enable extended speed selection */
+#define MDIO_CTRL1_SPEEDSELEXT		(BMCR_SPEED1000 | BMCR_SPEED100)
+/* All speed selection bits */
+#define MDIO_CTRL1_SPEEDSEL		(MDIO_CTRL1_SPEEDSELEXT | 0x003c)
+#define MDIO_CTRL1_FULLDPLX		BMCR_FULLDPLX
+#define MDIO_CTRL1_LPOWER		BMCR_PDOWN
+#define MDIO_CTRL1_RESET		BMCR_RESET
+#define MDIO_PMA_CTRL1_LOOPBACK		0x0001
+#define MDIO_PMA_CTRL1_SPEED1000	BMCR_SPEED1000
+#define MDIO_PMA_CTRL1_SPEED100		BMCR_SPEED100
+#define MDIO_PCS_CTRL1_LOOPBACK		BMCR_LOOPBACK
+#define MDIO_PHYXS_CTRL1_LOOPBACK	BMCR_LOOPBACK
+#define MDIO_AN_CTRL1_RESTART		BMCR_ANRESTART
+#define MDIO_AN_CTRL1_ENABLE		BMCR_ANENABLE
+#define MDIO_AN_CTRL1_XNP		0x2000	/* Enable extended next page */
+
+/* 10 Gb/s */
+#define MDIO_CTRL1_SPEED10G		(MDIO_CTRL1_SPEEDSELEXT | 0x00)
+/* 10PASS-TS/2BASE-TL */
+#define MDIO_CTRL1_SPEED10P2B		(MDIO_CTRL1_SPEEDSELEXT | 0x04)
+
+/* Status register 1. */
+#define MDIO_STAT1_LPOWERABLE		0x0002	/* Low-power ability */
+#define MDIO_STAT1_LSTATUS		BMSR_LSTATUS
+#define MDIO_STAT1_FAULT		0x0080	/* Fault */
+#define MDIO_AN_STAT1_LPABLE		0x0001	/* Link partner AN ability */
+#define MDIO_AN_STAT1_ABLE		BMSR_ANEGCAPABLE
+#define MDIO_AN_STAT1_RFAULT		BMSR_RFAULT
+#define MDIO_AN_STAT1_COMPLETE		BMSR_ANEGCOMPLETE
+#define MDIO_AN_STAT1_PAGE		0x0040	/* Page received */
+#define MDIO_AN_STAT1_XNP		0x0080	/* Extended next page status */
+
+/* Speed register. */
+#define MDIO_SPEED_10G			0x0001	/* 10G capable */
+#define MDIO_PMA_SPEED_2B		0x0002	/* 2BASE-TL capable */
+#define MDIO_PMA_SPEED_10P		0x0004	/* 10PASS-TS capable */
+#define MDIO_PMA_SPEED_1000		0x0010	/* 1000M capable */
+#define MDIO_PMA_SPEED_100		0x0020	/* 100M capable */
+#define MDIO_PMA_SPEED_10		0x0040	/* 10M capable */
+#define MDIO_PCS_SPEED_10P2B		0x0002	/* 10PASS-TS/2BASE-TL capable */
+
+/* Device present registers. */
+#define MDIO_DEVS_PRESENT(devad)	(1 << (devad))
+#define MDIO_DEVS_PMAPMD		MDIO_DEVS_PRESENT(MDIO_MMD_PMAPMD)
+#define MDIO_DEVS_WIS			MDIO_DEVS_PRESENT(MDIO_MMD_WIS)
+#define MDIO_DEVS_PCS			MDIO_DEVS_PRESENT(MDIO_MMD_PCS)
+#define MDIO_DEVS_PHYXS			MDIO_DEVS_PRESENT(MDIO_MMD_PHYXS)
+#define MDIO_DEVS_DTEXS			MDIO_DEVS_PRESENT(MDIO_MMD_DTEXS)
+#define MDIO_DEVS_TC			MDIO_DEVS_PRESENT(MDIO_MMD_TC)
+#define MDIO_DEVS_AN			MDIO_DEVS_PRESENT(MDIO_MMD_AN)
+#define MDIO_DEVS_C22EXT		MDIO_DEVS_PRESENT(MDIO_MMD_C22EXT)
+#define MDIO_DEVS_VEND1			MDIO_DEVS_PRESENT(MDIO_MMD_VEND1)
+#define MDIO_DEVS_VEND2			MDIO_DEVS_PRESENT(MDIO_MMD_VEND2)
+
+
+/* Control register 2. */
+#define MDIO_PMA_CTRL2_TYPE		0x000f	/* PMA/PMD type selection */
+#define MDIO_PMA_CTRL2_10GBCX4		0x0000	/* 10GBASE-CX4 type */
+#define MDIO_PMA_CTRL2_10GBEW		0x0001	/* 10GBASE-EW type */
+#define MDIO_PMA_CTRL2_10GBLW		0x0002	/* 10GBASE-LW type */
+#define MDIO_PMA_CTRL2_10GBSW		0x0003	/* 10GBASE-SW type */
+#define MDIO_PMA_CTRL2_10GBLX4		0x0004	/* 10GBASE-LX4 type */
+#define MDIO_PMA_CTRL2_10GBER		0x0005	/* 10GBASE-ER type */
+#define MDIO_PMA_CTRL2_10GBLR		0x0006	/* 10GBASE-LR type */
+#define MDIO_PMA_CTRL2_10GBSR		0x0007	/* 10GBASE-SR type */
+#define MDIO_PMA_CTRL2_10GBLRM		0x0008	/* 10GBASE-LRM type */
+#define MDIO_PMA_CTRL2_10GBT		0x0009	/* 10GBASE-T type */
+#define MDIO_PMA_CTRL2_10GBKX4		0x000a	/* 10GBASE-KX4 type */
+#define MDIO_PMA_CTRL2_10GBKR		0x000b	/* 10GBASE-KR type */
+#define MDIO_PMA_CTRL2_1000BT		0x000c	/* 1000BASE-T type */
+#define MDIO_PMA_CTRL2_1000BKX		0x000d	/* 1000BASE-KX type */
+#define MDIO_PMA_CTRL2_100BTX		0x000e	/* 100BASE-TX type */
+#define MDIO_PMA_CTRL2_10BT		0x000f	/* 10BASE-T type */
+#define MDIO_PCS_CTRL2_TYPE		0x0003	/* PCS type selection */
+#define MDIO_PCS_CTRL2_10GBR		0x0000	/* 10GBASE-R type */
+#define MDIO_PCS_CTRL2_10GBX		0x0001	/* 10GBASE-X type */
+#define MDIO_PCS_CTRL2_10GBW		0x0002	/* 10GBASE-W type */
+#define MDIO_PCS_CTRL2_10GBT		0x0003	/* 10GBASE-T type */
+
+/* Status register 2. */
+#define MDIO_STAT2_RXFAULT		0x0400	/* Receive fault */
+#define MDIO_STAT2_TXFAULT		0x0800	/* Transmit fault */
+#define MDIO_STAT2_DEVPRST		0xc000	/* Device present */
+#define MDIO_STAT2_DEVPRST_VAL		0x8000	/* Device present value */
+#define MDIO_PMA_STAT2_LBABLE		0x0001	/* PMA loopback ability */
+#define MDIO_PMA_STAT2_10GBEW		0x0002	/* 10GBASE-EW ability */
+#define MDIO_PMA_STAT2_10GBLW		0x0004	/* 10GBASE-LW ability */
+#define MDIO_PMA_STAT2_10GBSW		0x0008	/* 10GBASE-SW ability */
+#define MDIO_PMA_STAT2_10GBLX4		0x0010	/* 10GBASE-LX4 ability */
+#define MDIO_PMA_STAT2_10GBER		0x0020	/* 10GBASE-ER ability */
+#define MDIO_PMA_STAT2_10GBLR		0x0040	/* 10GBASE-LR ability */
+#define MDIO_PMA_STAT2_10GBSR		0x0080	/* 10GBASE-SR ability */
+#define MDIO_PMD_STAT2_TXDISAB		0x0100	/* PMD TX disable ability */
+#define MDIO_PMA_STAT2_EXTABLE		0x0200	/* Extended abilities */
+#define MDIO_PMA_STAT2_RXFLTABLE	0x1000	/* Receive fault ability */
+#define MDIO_PMA_STAT2_TXFLTABLE	0x2000	/* Transmit fault ability */
+#define MDIO_PCS_STAT2_10GBR		0x0001	/* 10GBASE-R capable */
+#define MDIO_PCS_STAT2_10GBX		0x0002	/* 10GBASE-X capable */
+#define MDIO_PCS_STAT2_10GBW		0x0004	/* 10GBASE-W capable */
+#define MDIO_PCS_STAT2_RXFLTABLE	0x1000	/* Receive fault ability */
+#define MDIO_PCS_STAT2_TXFLTABLE	0x2000	/* Transmit fault ability */
+
+/* Transmit disable register. */
+#define MDIO_PMD_TXDIS_GLOBAL		0x0001	/* Global PMD TX disable */
+#define MDIO_PMD_TXDIS_0		0x0002	/* PMD TX disable 0 */
+#define MDIO_PMD_TXDIS_1		0x0004	/* PMD TX disable 1 */
+#define MDIO_PMD_TXDIS_2		0x0008	/* PMD TX disable 2 */
+#define MDIO_PMD_TXDIS_3		0x0010	/* PMD TX disable 3 */
+
+/* Receive signal detect register. */
+#define MDIO_PMD_RXDET_GLOBAL		0x0001	/* Global PMD RX signal detect */
+#define MDIO_PMD_RXDET_0		0x0002	/* PMD RX signal detect 0 */
+#define MDIO_PMD_RXDET_1		0x0004	/* PMD RX signal detect 1 */
+#define MDIO_PMD_RXDET_2		0x0008	/* PMD RX signal detect 2 */
+#define MDIO_PMD_RXDET_3		0x0010	/* PMD RX signal detect 3 */
+
+/* Extended abilities register. */
+#define MDIO_PMA_EXTABLE_10GCX4		0x0001	/* 10GBASE-CX4 ability */
+#define MDIO_PMA_EXTABLE_10GBLRM	0x0002	/* 10GBASE-LRM ability */
+#define MDIO_PMA_EXTABLE_10GBT		0x0004	/* 10GBASE-T ability */
+#define MDIO_PMA_EXTABLE_10GBKX4	0x0008	/* 10GBASE-KX4 ability */
+#define MDIO_PMA_EXTABLE_10GBKR		0x0010	/* 10GBASE-KR ability */
+#define MDIO_PMA_EXTABLE_1000BT		0x0020	/* 1000BASE-T ability */
+#define MDIO_PMA_EXTABLE_1000BKX	0x0040	/* 1000BASE-KX ability */
+#define MDIO_PMA_EXTABLE_100BTX		0x0080	/* 100BASE-TX ability */
+#define MDIO_PMA_EXTABLE_10BT		0x0100	/* 10BASE-T ability */
+
+/* PHY XGXS lane state register. */
+#define MDIO_PHYXS_LNSTAT_SYNC0		0x0001
+#define MDIO_PHYXS_LNSTAT_SYNC1		0x0002
+#define MDIO_PHYXS_LNSTAT_SYNC2		0x0004
+#define MDIO_PHYXS_LNSTAT_SYNC3		0x0008
+#define MDIO_PHYXS_LNSTAT_ALIGN		0x1000
+
+/* PMA 10GBASE-T pair swap & polarity */
+#define MDIO_PMA_10GBT_SWAPPOL_ABNX	0x0001	/* Pair A/B uncrossed */
+#define MDIO_PMA_10GBT_SWAPPOL_CDNX	0x0002	/* Pair C/D uncrossed */
+#define MDIO_PMA_10GBT_SWAPPOL_AREV	0x0100	/* Pair A polarity reversed */
+#define MDIO_PMA_10GBT_SWAPPOL_BREV	0x0200	/* Pair B polarity reversed */
+#define MDIO_PMA_10GBT_SWAPPOL_CREV	0x0400	/* Pair C polarity reversed */
+#define MDIO_PMA_10GBT_SWAPPOL_DREV	0x0800	/* Pair D polarity reversed */
+
+/* PMA 10GBASE-T TX power register. */
+#define MDIO_PMA_10GBT_TXPWR_SHORT	0x0001	/* Short-reach mode */
+
+/* PMA 10GBASE-T SNR registers. */
+/* Value is SNR margin in dB, clamped to range [-127, 127], plus 0x8000. */
+#define MDIO_PMA_10GBT_SNR_BIAS		0x8000
+#define MDIO_PMA_10GBT_SNR_MAX		127
+
+/* PMA 10GBASE-R FEC ability register. */
+#define MDIO_PMA_10GBR_FECABLE_ABLE	0x0001	/* FEC ability */
+#define MDIO_PMA_10GBR_FECABLE_ERRABLE	0x0002	/* FEC error indic. ability */
+
+/* PCS 10GBASE-R/-T status register 1. */
+#define MDIO_PCS_10GBRT_STAT1_BLKLK	0x0001	/* Block lock attained */
+
+/* PCS 10GBASE-R/-T status register 2. */
+#define MDIO_PCS_10GBRT_STAT2_ERR	0x00ff
+#define MDIO_PCS_10GBRT_STAT2_BER	0x3f00
+
+/* AN 10GBASE-T control register. */
+#define MDIO_AN_10GBT_CTRL_ADV10G	0x1000	/* Advertise 10GBASE-T */
+
+/* AN 10GBASE-T status register. */
+#define MDIO_AN_10GBT_STAT_LPTRR	0x0200	/* LP training reset req. */
+#define MDIO_AN_10GBT_STAT_LPLTABLE	0x0400	/* LP loop timing ability */
+#define MDIO_AN_10GBT_STAT_LP10G	0x0800	/* LP is 10GBT capable */
+#define MDIO_AN_10GBT_STAT_REMOK	0x1000	/* Remote OK */
+#define MDIO_AN_10GBT_STAT_LOCOK	0x2000	/* Local OK */
+#define MDIO_AN_10GBT_STAT_MS		0x4000	/* Master/slave config */
+#define MDIO_AN_10GBT_STAT_MSFLT	0x8000	/* Master/slave config fault */
+
+/* AN EEE Advertisement register. */
+#define MDIO_AN_EEE_ADV_100TX		0x0002	/* Advertise 100TX EEE cap */
+#define MDIO_AN_EEE_ADV_1000T		0x0004	/* Advertise 1000T EEE cap */
+
+/* LASI RX_ALARM control/status registers. */
+#define MDIO_PMA_LASI_RX_PHYXSLFLT	0x0001	/* PHY XS RX local fault */
+#define MDIO_PMA_LASI_RX_PCSLFLT	0x0008	/* PCS RX local fault */
+#define MDIO_PMA_LASI_RX_PMALFLT	0x0010	/* PMA/PMD RX local fault */
+#define MDIO_PMA_LASI_RX_OPTICPOWERFLT	0x0020	/* RX optical power fault */
+#define MDIO_PMA_LASI_RX_WISLFLT	0x0200	/* WIS local fault */
+
+/* LASI TX_ALARM control/status registers. */
+#define MDIO_PMA_LASI_TX_PHYXSLFLT	0x0001	/* PHY XS TX local fault */
+#define MDIO_PMA_LASI_TX_PCSLFLT	0x0008	/* PCS TX local fault */
+#define MDIO_PMA_LASI_TX_PMALFLT	0x0010	/* PMA/PMD TX local fault */
+#define MDIO_PMA_LASI_TX_LASERPOWERFLT	0x0080	/* Laser output power fault */
+#define MDIO_PMA_LASI_TX_LASERTEMPFLT	0x0100	/* Laser temperature fault */
+#define MDIO_PMA_LASI_TX_LASERBICURRFLT	0x0200	/* Laser bias current fault */
+
+/* LASI control/status registers. */
+#define MDIO_PMA_LASI_LSALARM		0x0001	/* LS_ALARM enable/status */
+#define MDIO_PMA_LASI_TXALARM		0x0002	/* TX_ALARM enable/status */
+#define MDIO_PMA_LASI_RXALARM		0x0004	/* RX_ALARM enable/status */
+
+/* Mapping between MDIO PRTAD/DEVAD and mii_ioctl_data::phy_id */
+
+#define MDIO_PHY_ID_C45			0x8000
+#define MDIO_PHY_ID_PRTAD		0x03e0
+#define MDIO_PHY_ID_DEVAD		0x001f
+#define MDIO_PHY_ID_C45_MASK						\
+	(MDIO_PHY_ID_C45 | MDIO_PHY_ID_PRTAD | MDIO_PHY_ID_DEVAD)
+
+#define MDIO_PRTAD_NONE			(-1)
+#define MDIO_DEVAD_NONE			(-1)
+#define MDIO_EMULATE_C22		4
+
+#endif /* __LINUX_MDIO_H__ */
diff --git a/include/miiphy.h b/include/miiphy.h
index 34ebce6..7e70cf8 100644
--- a/include/miiphy.h
+++ b/include/miiphy.h
@@ -34,8 +34,18 @@
 #ifndef _miiphy_h_
 #define _miiphy_h_
 
+#include <common.h>
 #include <linux/mii.h>
+#include <linux/list.h>
 #include <net.h>
+#include <phy.h>
+
+struct legacy_mii_dev {
+	int (*read)(const char *devname, unsigned char addr,
+		     unsigned char reg, unsigned short *value);
+	int (*write)(const char *devname, unsigned char addr,
+		      unsigned char reg, unsigned short value);
+};
 
 int miiphy_read(const char *devname, unsigned char addr, unsigned char reg,
 		 unsigned short *value);
@@ -61,9 +71,16 @@ void miiphy_register(const char *devname,
 
 int miiphy_set_current_dev(const char *devname);
 const char *miiphy_get_current_dev(void);
+struct mii_dev *mdio_get_current_dev(void);
+struct mii_dev *miiphy_get_dev_by_name(const char *devname);
+struct phy_device *mdio_phydev_for_ethname(const char *devname);
 
 void miiphy_listdev(void);
 
+struct mii_dev *mdio_alloc(void);
+int mdio_register(struct mii_dev *bus);
+void mdio_list_devices(void);
+
 #ifdef CONFIG_BITBANGMII
 
 #define BB_MII_DEVNAME	"bb_miiphy"
diff --git a/include/phy.h b/include/phy.h
new file mode 100644
index 0000000..2abd23b
--- /dev/null
+++ b/include/phy.h
@@ -0,0 +1,219 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *	Andy Fleming <afleming@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * This file pretty much stolen from Linux's mii.h/ethtool.h/phy.h
+ */
+
+#ifndef _PHY_H
+#define _PHY_H
+
+#include <linux/list.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/mdio.h>
+
+#define PHY_MAX_ADDR 32
+
+#define PHY_BASIC_FEATURES	(SUPPORTED_10baseT_Half | \
+				 SUPPORTED_10baseT_Full | \
+				 SUPPORTED_100baseT_Half | \
+				 SUPPORTED_100baseT_Full | \
+				 SUPPORTED_Autoneg | \
+				 SUPPORTED_TP | \
+				 SUPPORTED_MII)
+
+#define PHY_GBIT_FEATURES	(PHY_BASIC_FEATURES | \
+				 SUPPORTED_1000baseT_Half | \
+				 SUPPORTED_1000baseT_Full)
+
+#define PHY_10G_FEATURES	(PHY_GBIT_FEATURES | \
+				SUPPORTED_10000baseT_Full)
+
+#define PHY_ANEG_TIMEOUT	4000
+
+
+typedef enum {
+	PHY_INTERFACE_MODE_MII,
+	PHY_INTERFACE_MODE_GMII,
+	PHY_INTERFACE_MODE_SGMII,
+	PHY_INTERFACE_MODE_TBI,
+	PHY_INTERFACE_MODE_RMII,
+	PHY_INTERFACE_MODE_RGMII,
+	PHY_INTERFACE_MODE_RGMII_ID,
+	PHY_INTERFACE_MODE_RGMII_RXID,
+	PHY_INTERFACE_MODE_RGMII_TXID,
+	PHY_INTERFACE_MODE_RTBI,
+	PHY_INTERFACE_MODE_XGMII,
+	PHY_INTERFACE_MODE_NONE	/* Must be last */
+} phy_interface_t;
+
+static const char *phy_interface_strings[] = {
+	[PHY_INTERFACE_MODE_MII]		= "mii",
+	[PHY_INTERFACE_MODE_GMII]		= "gmii",
+	[PHY_INTERFACE_MODE_SGMII]		= "sgmii",
+	[PHY_INTERFACE_MODE_TBI]		= "tbi",
+	[PHY_INTERFACE_MODE_RMII]		= "rmii",
+	[PHY_INTERFACE_MODE_RGMII]		= "rgmii",
+	[PHY_INTERFACE_MODE_RGMII_ID]		= "rgmii-id",
+	[PHY_INTERFACE_MODE_RGMII_RXID]		= "rgmii-rxid",
+	[PHY_INTERFACE_MODE_RGMII_TXID]		= "rgmii-txid",
+	[PHY_INTERFACE_MODE_RTBI]		= "rtbi",
+	[PHY_INTERFACE_MODE_XGMII]		= "xgmii",
+	[PHY_INTERFACE_MODE_NONE]		= "",
+};
+
+static inline const char *phy_string_for_interface(phy_interface_t i)
+{
+	/* Default to unknown */
+	if (i > PHY_INTERFACE_MODE_NONE)
+		i = PHY_INTERFACE_MODE_NONE;
+
+	return phy_interface_strings[i];
+}
+
+
+struct phy_device;
+
+#define MDIO_NAME_LEN 32
+
+struct mii_dev {
+	struct list_head link;
+	char name[MDIO_NAME_LEN];
+	void *priv;
+	int (*read)(struct mii_dev *bus, int addr, int devad, int reg);
+	int (*write)(struct mii_dev *bus, int addr, int devad, int reg,
+			u16 val);
+	int (*reset)(struct mii_dev *bus);
+	struct phy_device *phymap[PHY_MAX_ADDR];
+	u32 phy_mask;
+};
+
+/* struct phy_driver: a structure which defines PHY behavior
+ *
+ * uid will contain a number which represents the PHY.  During
+ * startup, the driver will poll the PHY to find out what its
+ * UID--as defined by registers 2 and 3--is.  The 32-bit result
+ * gotten from the PHY will be masked to
+ * discard any bits which may change based on revision numbers
+ * unimportant to functionality
+ *
+ */
+struct phy_driver {
+	char *name;
+	unsigned int uid;
+	unsigned int mask;
+	unsigned int mmds;
+
+	u32 features;
+
+	/* Called to do any driver startup necessities */
+	/* Will be called during phy_connect */
+	int (*probe)(struct phy_device *phydev);
+
+	/* Called to configure the PHY, and modify the controller
+	 * based on the results.  Should be called after phy_connect */
+	int (*config)(struct phy_device *phydev);
+
+	/* Called when starting up the controller */
+	int (*startup)(struct phy_device *phydev);
+
+	/* Called when bringing down the controller */
+	int (*shutdown)(struct phy_device *phydev);
+
+	struct list_head list;
+};
+
+struct phy_device {
+	/* Information about the PHY type */
+	/* And management functions */
+	struct mii_dev *bus;
+	struct phy_driver *drv;
+	void *priv;
+
+	struct eth_device *dev;
+
+	/* forced speed & duplex (no autoneg)
+	 * partner speed & duplex & pause (autoneg)
+	 */
+	int speed;
+	int duplex;
+
+	/* The most recently read link state */
+	int link;
+	int port;
+	phy_interface_t interface;
+
+	u32 advertising;
+	u32 supported;
+	u32 mmds;
+
+	int autoneg;
+	int addr;
+	int pause;
+	int asym_pause;
+	u32 phy_id;
+	u32 flags;
+};
+
+static inline int phy_read(struct phy_device *phydev, int devad, int regnum)
+{
+	struct mii_dev *bus = phydev->bus;
+
+	return bus->read(bus, phydev->addr, devad, regnum);
+}
+
+static inline int phy_write(struct phy_device *phydev, int devad, int regnum,
+			u16 val)
+{
+	struct mii_dev *bus = phydev->bus;
+
+	return bus->write(bus, phydev->addr, devad, regnum, val);
+}
+
+#ifdef CONFIG_PHYLIB_10G
+extern struct phy_driver gen10g_driver;
+
+/* For now, XGMII is the only 10G interface */
+static inline int is_10g_interface(phy_interface_t interface)
+{
+	return interface == PHY_INTERFACE_MODE_XGMII;
+}
+
+#endif
+
+int phy_init(void);
+int phy_reset(struct phy_device *phydev);
+struct phy_device *phy_connect(struct mii_dev *bus, int addr,
+				struct eth_device *dev,
+				phy_interface_t interface);
+int phy_startup(struct phy_device *phydev);
+int phy_config(struct phy_device *phydev);
+int phy_shutdown(struct phy_device *phydev);
+int phy_register(struct phy_driver *drv);
+int genphy_config_aneg(struct phy_device *phydev);
+int genphy_update_link(struct phy_device *phydev);
+int genphy_config(struct phy_device *phydev);
+int genphy_startup(struct phy_device *phydev);
+int genphy_shutdown(struct phy_device *phydev);
+int gen10g_config(struct phy_device *phydev);
+int gen10g_startup(struct phy_device *phydev);
+int gen10g_shutdown(struct phy_device *phydev);
+int gen10g_discover_mmds(struct phy_device *phydev);
+
+#endif
diff --git a/net/eth.c b/net/eth.c
index 3a7ff50..6523834 100644
--- a/net/eth.c
+++ b/net/eth.c
@@ -25,6 +25,7 @@
 #include <command.h>
 #include <net.h>
 #include <miiphy.h>
+#include <phy.h>
 
 void eth_parse_enetaddr(const char *addr, uchar *enetaddr)
 {
@@ -217,6 +218,11 @@ int eth_initialize(bd_t *bis)
 #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
 	miiphy_init();
 #endif
+
+#ifdef CONFIG_PHYLIB
+	phy_init();
+#endif
+
 	/*
 	 * If board-specific initialization exists, call it.
 	 * If not, call a CPU-specific one